TURN-TiLT WiNDOWs A11.16 CHRONO ACCessORies
|
|
- Britney Pearson
- 5 years ago
- Views:
Transcription
1 A11 TURN-TILT WINDOWS A11.16 CHRONO Accessories Waregemstraat Zulte - Belgium - T F commercial@sobinco.com -
2 Contents 1. Window stay n , -902 and A Additional arm n and A Narrow and small windows... A Sets for small windows A Rod for narrow windows A Jigs... A Jig set for wedges A Installation jigs CHRONO INVISI hinges A Night vent device n A Night vent device n A Magnet contact n A Door catch n A Adjustable wedge n A CHRONO INVISION installation set n A Assembly tables and cabinets... A Assembly table for set packaging n A Assembly table for bulk packaging n A Small cabinet n A Large cabinet n A A
3 1. Window stay n , -902 and -903 The window stay restricts the opening angle of the window in turn position. The window stay is required in public buildings. A11.16 The window stay should be used for safety purposes or where the opening arc may be obstructed. The position of the stay will dictate the opening angle of the window. The window stay is detachable by turning rivet R with a 4 mm hexagon key. The window stay has an incorporated adjustable friction by tightening the screw S, which can hold the vent in any turn position. CHRONO CHRONO INVISION CHRONO INVISI A
4 2. Additional arm n and An additional arm may be used on vents over 1400 mm wide. The additional arm provides greater stability, especially for wide and heavy windows in tilt position. The additional arm is non-handed and can only be used for CHRONO and CHRONO INVISION. N CHRONO standard and CHRONO PLUS rod vent part frame part jig N CHRONO SAFE rod vent part frame part jig Attention: For CHRONO SAFE and CHRONO INVISION SAFE with a vent width from 1401 to 1450 mm the link arm 2 must be used instead of the normally used link arm 3. CHRONO SAFE CHRONO INVISION SAFE R(L) (groove 14/18) R(L) (groove 10/14) R(L) (groove 14/18) R(L) (groove 10/14) A
5 3. Narrow and small windows 3.1. Sets for small windows Set n With connection piece This set can be used for turn-tilt windows, tilt-turn windows, side hung windows as well as tilt windows with vertically mounted handle. The set is only available for CHRONO standard and CHRONO PLUS. Set n contains a connection piece n for standard handle. Size range: vent height Fh = mm. Procedure: Determine rod lengths and cut off rods n Drill hole ø6 mm in the rod. With lockcase These sets n and can be used for turn-tilt windows, tilt-turn windows, side hung windows as well as tilt windows with vertically mounted handle. The sets below are only available for CHRONO standard and CHRONO PLUS. Set n Set n Sets: N : with lockcase for operation with clip-on handle n N : with lockcase for operation with handle with square spindle 7 mm. Size range: vent height Fh = mm. Procedure: Determine rod lengths and cut off rods n Drill hole ø6 mm in the rod. A
6 3.2. Rod for narrow windows Cut-off rod n in zinc alloy which is mounted between the corner transmission and the link arm. This rod is also used for CHRONO PLUS and SAFE. Size range: CHRONO standard and PLUS: vent width mm. CHRONO SAFE: vent width mm. CHRONO INVISION standard and PLUS: vent width mm. CHRONO INVISION SAFE: vent width mm. CHRONO INVISI standard and PLUS: vent width mm. CHRONO INVISI SAFE: vent width mm. Must be ordered separately. Installation: 1. Corner transmission Disconnect (and break) the snap-off pin and pull out the toothed part out all the way. Cut the toothed part at the indication groove. Position this piece again in accordance with the position of the broken snap-off pin. 2. Rod n Cut the rod in accordance with the vent width at the appropriate indication groove. 3. Link arm Remove (by using a tool) the connection piece of the link arm. The rod is to be connected to the link arm hole. 4. Connection Connect the 3 pieces to each other. A
7 4. Jigs 4.1. Jig set for wedges n (BE) Beige n n (B) Blue (O) Orange (C) Cyan (P) Purple (R) Red (Rz) Pink (Br) Brown (G) Green 4.2. Installation jigs CHRONO INVISI hinges The jig n is a drilling jig to drill the fixing holes for the bottom hinge as well as for the top hinge. The jig n is used to position the top hinge. n n A
8 5. Night vent device n General The 12 mm night vent position device allows you to ventilate without significant heat and energy loss. Economical and discrete. The night vent position device is especially developed for turn-tilt windows and sets the window in a ventilation position of 12 mm by means of a special wedge on the frame. The frame part is mounted at a fixed distance from the top and the vent part is mounted below the corner transmission. This night vent position device can be turned off and ensures a perfect operation of your window. Very simple operation: if the device is disengaged: standard tilt opening of ±170 mm = summer position if the device is operational: tilt opening is restricted to 12 mm = winter position The night vent position device n is suitable for frame groove of 14/18 mm and frame groove of 10/14 mm. Operation NIGHT VENT DEVICE IS OPERATIONAL DISENGAGE NIGHT VENT DEVICE Closed position Turn position Tilt position Turn position Lift and turn 180 Closed position = roller is completely above the lever Turn position = roller turns above the lever Tilt position = roller operates the lever Put the handle in turn position (90 ) Lift the lever and turn 180 A
9 Air flow Air flow chart in accordance with standard EN and NBN EN 13141/1. Fb+Fh (m) Q(m³/h) Fb+Fh (m) Q(m³/h) Installation for a CHRONO standard and PLUS turn-tilt window 234 jig or A
10 Installation for a CHRONO SAFE turn-tilt window 234 Only if Fh < 1800 mm A
11 6. Night vent device n General The 4 mm night vent position device allows you to ventilate without significant heat and energy loss. Economical and discreet. The night vent position device, which is placed on the top side, is especially developed for turn-tilt windows and sets a ventilation position of 4 mm by means of a special wedge on the frame. The frame part is mounted at a fixed distance from the hinge side and the vent part is mounted close to the corner transmission. The ventilation position is reached between the tilt position and the turn position, when the handle is turned over an angle of 45. Tilt position Night vent position Night vent position bolt Turn position Closed position The night vent position device n is valid for frame groove of 14/18 mm and frame groove of 10/14 mm. A
12 Installation for a CHRONO standard and CHRONO PLUS turn-tilt window Turn-tilt Installation for a CHRONO INVISION standard and CHRONO INVISION PLUS turn-tilt window Turn-tilt A
13 Installation for a CHRONO SAFE turn-tilt window Turn-tilt The rods n and P are already included in the base set. Installation for a CHRONO INVISION SAFE turn-tilt window Turn-tilt The rods n and P are already included in the base set. A
14 7. Magnet contact n General Magnet contact n rod with roller fixing magnet contact magnet contact cap 2 St 2.9x15Din7981 screw Magnetic contact to check whether the window is open or closed. Anti-burglary: when the window is not closed, an alarm system can be activated. The set can be used for CHRONO standard and PLUS as well as CHRONO SAFE. Same installation for turn-tilt windows and tilt-turn windows. Suitable for frame groove 14/18 mm and 10/14 mm. Technical data: Cable: 6 m - LIYY 4x 0.14 mm² Maximum contact load: 10 W Maximum switching voltage: 100 VDC Maximum switching DC power: 0,5 A Cable temperature range: -25 to +70 C Protection class: IP68 Circuit diagram: control signal open contact A
15 Installation for a CHRONO standard and CHRONO PLUS turn-tilt window Turn-tilt Installation for a CHRONO INVISION standard and CHRONO INVISION PLUS turn-tilt window Turn-tilt A
16 Installation for a CHRONO SAFE turn-tilt window Turn-tilt Installation for a CHRONO INVISION SAFE turn-tilt window Turn-tilt A
17 8. Door catch n General Frame groove X 10/ mm 14/18 12 mm Adjustment range 5 mm or Door catch n (frame groove 14/18 mm) slotted rod locking roller wedge packer 3 St 4.2x25 Din7504P drilling screw Door catch n (frame groove 10/14 mm) slotted rod locking roller wedge packer 3 St 4.2x25 Din7504P drilling screw The door catch is designed to hold your windows and balcony doors closed without locking them. Function: the locking roller clips into the keep so that the window is temporarily kept closed without having to lock it. Installation: The door catch is mounted adjacent to the handle. The locking roller is screwed in the vent groove. The connection rod is slotted so it can slide past the fixed locking roller. Note: the door catch can also be mounted at the top or at the bottom (horizontal installation). Installation example: A
18 Installation for CHRONO standard and PLUS Locking roller position A
19 Installation for CHRONO SAFE Locking roller position A
20 9. Adjustable wedge n Wedge n is adjustable to increase or decrease the compression of the vent gasket. This can be important to ensure wind and water tightness of the window. The wedge is black passivated and can be applied for a frame groove of 14/18 mm and a frame groove of 10/14 mm. The adjustment range of the wedge is from -1 mm to +2 mm: position -1: more compression position 0: normal position position +2: less compression There are 3 marks on the wedge which indicate the 3 positions: A
21 10. CHRONO INVISION installation set n Drive short spinner A11.16 The drive short spinner has an ergonomic high-strength bi-material handle. The spinner is resistant to common chemicals. Chrome finish. Performance: according to ISO 3315, DIN 3122 and NF ISO Universal joint with hexagon The universal joint with embossed hexagon is slowed by a spring. The joint will remain in the adjusted position, in order to reach difficult accessible places. The use of the universal joint can save a lot of time. A
22 11. Assembly tables and cabinets Assembly table for set packaging n Width = 1070 mm Depth = 1230 mm Height = 1050 mm A
23 11.2. Assembly table for bulk packaging n Width = 1070 mm Depth = 1230 mm Height = 1050 mm Small boxes: 175 x 100 x 70 mm Large boxes: 255 x 150 x 120 mm A
24 11.3. Small cabinet n Width = 1220 mm Depth = 610 mm Height = 1660 mm A
25 11.4. Large cabinet n Width = 1470 mm Depth = 610 mm Height = 1960 mm A
26
C.3 CHRONO MISCELLANEOUS. Contents. turn-tilt- and tilt-turn window
C.3 Turn-tilt and tilt-turn windows CHRONO MISCELLANEOUS Contents 1. Night vent device n 30140-861 C.3.02 1.1. General C.3.02 1.2. Profile dimensions C.3.02 1.3. Operation C.3.03 1.4. Air flow C.3.03 1.5.
More informationC14.12 WINDOW STAYS C14 SIDE HUNG WINDOWS
C14 SIDE HUNG WINDOWS 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Window stays series 681-.. and n 684-12....03
More informationA12.11 SALTO 4008 A12 TURN-TILT WINDOWS
A12 TURN-TILT WINDOWS A12.11 01.05.2014 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General characteristics...
More informationB12.13 SALTO 4138 FOR SLOPING HEAD WINDOWS
B12 TILT-TURN WINDOWS B12.13 SALTO 4138 FOR SLOPING HEAD WINDOWS 01.11.2015 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS
More informationC12.11 SALTO 4208 C12 SIDE HUNG WINDOWS
C12 SIDE HUNG WINDOWS C12.11 01.07.2015 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General characteristics...
More informationC13.10 CHRONO LOCKCASE AND PERIMETER LOCKING SET C13 SIDE HUNG WINDOWS
C13 SIDE HUNG WINDOWS CHRONO LOCKCASE AND PERIMETER LOCKING SET 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS
More informationFrENcH casement windows D11.15 HINGES
D11 French casement windows HINGES 01.02.2014 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com Hinges Contents 1. General....03
More informationG11.11 INVISITOP FOR BOTTOM HUNG WINDOWS
G11 FAN LIGHT WINDOWS G11.11 50141 FOR BOTTOM HUNG WINDOWS 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS
More informationRC2 B11.09 CHRONO SAFE (RC2) B11 TILT-TURN WINDOWS
B11 TILT-TURN WINDOWS RC2 B11.09 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General characteristics...
More informationC.4.CHRONO TILT AND TURN
C.4. Contents General characteristics................... Base set n 31111, 31112 and 31113...... Centre locking set n 30140-30........... Selection of rods n 30000-................ page C.4.2 C.4.5 C.4.6
More informationB.1.CHRONO SIDE HUNG OPEN IN WINDOWS
B.1. SIDE HUNG OPEN IN Contents General characteristics................... page B.1.2 Base set n 20110...................... B.1.4 Centre locking sets n 30140-800 and 20140-35..........................
More informationC.9.CHRONO INVISI TILT AND TURN
C.9. Contents General characteristics... Base set (standard) n 31117, 31118 and 31119... Selection of rods n 30000-...... Installation instructions... Base set PLUS n 31517, 31518 and 31519 Installation
More informationRC2 E11.09 CHRONO SAFE (RC2) E11 BOTTOM HUNG OPEN IN WINDOWS
E11 BOTTOM HUNG OPEN IN WINDOWS RC2 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General characteristics...03
More informationK17.13 DOOR STAYS K17 DOORS
K17 DOORS K17.13 01.12.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Door stays n 684(C)-500...K17.13.03 1.1.
More informationF11.13 FRICTION HINGES F11 PROJECT-OUT WINDOWS AND TOP HUNG WINDOWS
F11 AND TOP HUNG WINDOWS F11.13 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General information...f11.13.03
More informationSingle locks series k
k12 Doors K12.13 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com Contents 1. Door locks series 8000... K12.13.03 1.1.
More informationA.10 CHRONO FOR PIVOTING WINDOWS. Contents. Horizontal and vertical pivoting windows
A.10 Hizontal and vertical pivoting windows CHRONO 10040 FOR PIVOTING WINDOWS Contents 1. General characteristics A.10.02 2. Base set n 10040 A.10.03 3. Centre locking set n 30140-800 A.10.04 4. Selection
More informationFurniture Fittings Hinges and Flap Fittings
Glass door hinge Area of application: For inset glass doors Glass door height: Max 1,200 mm Glass door width: Max 400 mm For door weight: Max 10 kg Material: Zinc alloy, steel, PVC Glass thickness: 6-10
More informationHinges and Flap Fittings Furniture Hinges
Butt hinge Material: Steel Length: 50 mm Flange thickness: 1.5 mm Barrel Ø: 8 mm Crank A, straight Ø Gap1 mm Mounting Nickel plated matt Left 1.08.717 Right 1.08.708 Brass plated Left 1.08.511 Right 1.08.502
More informationH13.11 HANDLES H13 HORIZONTAL AND VERTICAL PIVOT WINDOWS
H13 HORIZONTL N VERTIL PIVOT WINOWS 01.11.2015 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - coercial@sobinco.com - www.sobinco.com ONTENTS 1. General information....03
More informationFENSTERTECHNIK BESTELLKATALOG WINDOW TECHNOLOGY ORDER CATALOG SECTION Tilt&Turn Hardware UNI-JET SCF PVC
FENSTERTECHNIK BESTELLKATALOG WINDOW TECHNOLOGY ORDER CATALOG SECTION 06.2 Tilt&Turn Hardware UNI-JET SCF PVC Table of Contents 06.2 UNI-JET SCF PVC 06 2 DIRIGENT T&T Handle... 06.2.9 Tilt&Turn Sash...
More informationA.15 HANDLES FOR PERIMETER LOCKING SETS. Contents. Horizontal and vertical pivoting windows
.15 Horizontal and vertical pivoting windows HNLES FOR PERIMETER LOKING SETS ontents 1. General information.15.02 1.1. Handles series 501, 502 and 503.15.02 1.2. Handles series 5010, 5020 and 5030.15.02
More informationFor further assistance, call
RESTRICTORS - VARIOUS Inside: - Casement/Tilt & Turn Restrictor Catch - Door Restrictor - VS Rola Travel Restrictor - VS Sharks Fin Travel Restrictor - Door Safe T Bar Restrictors - January 2018 CASEMENT
More informationRestrictors & Security Devices. Hardware By Professionals For Professionals
Restrictors & Security Devices Hardware By Professionals For Professionals 102 103 Restrictors & Security Devices Contents RRestrictors & Security Devices Selection Mila stock a comprehensive range of
More informationK16.14 STAINLESS STEEL DOOR PULLS
K16 DOORS K16.14 01.06.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General... K16.14.03 1.1. General information
More informationHardware Solution for Windows
Hardware Solution for Windows Turn-Tilt Fittings Style 180 Turn-Tilt Fittings Standard Turn-Tilt Fittings Heavy Duty Dual Turn-Tilt Fitting Opening Restrictor Handle controlled opening arrester Wilh. Schlechtendahl
More informationTHE NEW HARDWARE SYSTEM ALU 540. Roto ALU 540. FB 44-0 GB July 2005 Alu B.U./J.S. (Translation: Prunty 9/05)
THE NEW HARDWARE SYSTEM ALU 540 1 APPLICATION RANGE Hinge-side compatible with all conventional Euro-chamber profiles Clampable hinge-side with preassembled clamp-strips Available for all standard opening
More informationHanging Cabinets & Accessories
.0 Hanging Cabinets & Accessories.1 Blum AVENTOS HK-Stay lift for wooden fronts or wide alu frames Material: Steel mechanism, plastic cover caps Finish: Mechanism galvanized, cover cap grey Adjustment:
More information29 Fit the air duct to the dashboard vent on the driver's side. 30 Fit the fuse board. 31 Fit the air duct to the floor vent.
854 2383 9 29 Fit the air duct to the dashboard vent on the driver's side. 30 Fit the fuse board. 31 Fit the air duct to the floor vent. 32 Fit the knee shield. 33 Fit the lower dashboard section. 34 Fit
More informationSmart Visofold 1000 Series Bi Fold Door System
Smart Visofold 1000 Series Bi Fold Door System 1 P a g e Smart Visofold 1000 Series - Recommended Design Limitations Minimum Sash Width Maximum Sash Width Maximum Sash Height Maximum Sash Weight 700mm
More informationCONTENT. Section. Introduction. Introduction. Hinges. Gears. Corner transmissions/ Middle locks/ Extensions. Stay arms. Additional elements
塑钢窗配件 Section Introduction CONTENT Introduction 1 Hinges 2 Gears 3 Corner transmissions/ Middle locks/ Extensions 4 Stay arms 5 Additional elements 6 Hardware set combinations 7 Tools / Instalation/ Adjustments
More informationHardware Solution for Windows
Hardware Solution for Windows Turn-Tilt Fittings Style 180 Turn-Tilt Fittings Standard Turn-Tilt Fittings Heavy Duty Dual Turn-Tilt Fitting Opening Restrictor Wilh. Schlechtendahl & Söhne GmbH & Co. KG
More informationTECHNOLOGY IN MOTION MACO MULTI-TREND TU.-ON. AND T&T FITTINGS. Installation instructions TIMBER WINDOWS
TECHNOLOGY IN MOTION TU.-ON. AND T&T FITTINGS Installation instructions TIMBER WINDOWS System designation: TO > Single routing DT > Double routing AS > Face fix fittings Note about surfaces fittings are
More informationGlass & Wooden Door Fittings
Glass & Wooden Door Fittings Product range: Door Sliders Door Track Plastic Glass Clamps Glass Door Channel Aluminium Glass Door Channel Plastic Glass Door Hinges Glass Door Locks Glass Sliding Door Systems
More informationUS FUTABA ESTABLISHED 1983 NEW IN THIS SECTION OFFICE LINE. Short Type 4 5-1/8" ( mm) 23.5 Ø /4" 45 mm. 1-3/16" 30 mm 5/8" 15.
0 5 1-3/4" 1-3/16" 30 5/8" 15.8 15 ESTABLISHED 1983 31/64" 1 Ø 100 Ø + 1/" 1" 1/8" NEW IN THIS SECTION " Short Type 4 5-1/8" (100 130 ) Ø =, & 80 11 13 0 Ø 6 Extra Heavy Duty Adjustable Floor Leveler (Page
More informationDICTATOR RTS Tube Door Closer
DICTATOR RTS Tube Door Closer The "Invisible" Door Closer The DICTATOR RTS tube door closer is virtually invisible because being built into the door. The joint can only be seen when the door is open. The
More informationK B J K A C H D E I F. Single and Bi-Parting Electric Sliding Doors with Automatic Operator (ICC-5) Parts List. R-PLUS Cold Storage Doors
Single and Bi-Parting Electric Sliding Doors with Automatic Operator (ICC-) Parts List K B J K A C H G Release Date: -0 D E R-PLUS Cold Storage Doors NE 9th Portland, Oregon 90 Toll Free () 0-99 Fax (0)
More informationLimit switches Osiswitch Classic For hoisting and materials handling applications, type XCR Complete switches with 1 cable entry
References, characteristics For hoisting and materials handling applications, type XCR Complete switches with cable entry Type of head Rotary with spring return to off position Stay put Maximum displacement
More informationABOUT KJN ALUMINIUM PROFILES
P R O D U C T C ATA L O G U E ABOUT KJN ALUMINIUM PROFILES Our range of Aluminum Profile is available in a large range of sizes starting with 20 x 20 through to 100 x 200 making it suitable to use in all
More informationKINVARO KINVARO LIFTER SYSTEMS. Modern design, innovative technology and ease of operation for wall cabinetry.
KINVARO KINVARO LIFTER SYSTEMS Modern design, innovative technology and ease of operation for wall cabinetry. www.grassusa.com Exclusive lifter systems Kinvaro provides the perfect solution for every application.
More informationMaterial: Hinge Parts: zinc die, matt chrome plated, or zinc die, matt black. Pin: stainless steel Nut plate: steel, zinc plated
4-249 Hinge Pr01 180 Small elegant hinge. 180 Opening. Adjustments are possible with respective bores provided. The nut plate can be mounted in different ways, according to the application. zinc die, matt
More informationTechnical Manual DICTAMAT 304 AZ. Door Drive Unit. for hinged lift landing doors. Technical Data
Door Drive Unit The is an electrical door drive unit which automatically opens hinged lift doors up to 200 kg. As the operating arm is not directly fixed to the door, all landing doors in the lift can
More informationWindow Locking 10YEAR. whitco.com.au
Window Locking 10YEAR whitco.com.au Contents CYL4 Push Lock CYL4 Mini Push Lock CYL4 Multi Bolt CYL4 Patio Bolt page 4 page 6 page 7 page 8 CYL4 Window Bolt CYL4 Mini Window Bolt Keyed Sash Lock Safety
More informationCut out PRODUCT CODE HANDLE BODY FINISH MATERIAL MODUL. 5 mm Double bit 8 mm Square 9 mm Triangular Button. Stainless steel dust cap (Keyed alike) 03
ROD-LATCH SYSTEM LINEAR HANDLE LOCK 204 V : 1 With mechanism Cut out Ergonomic and modern design Locking and unlocking by linear movement Suitable for inside & outside gasketing applications Swing handle
More informationDICTATOR Door Checks
DICTATOR Door Checks Ensure Doors to Close Quietly. Doors can be incredibly noisy. Not only when people slam them, but also due to air pressure, gusts of wind and inadequate door closers. The more violent
More informationIndexing Plunger 417. Triangular Knobs, Made from Plastic. Triangular Knobs, Made from Stainless Steel
Standard Parts for Operating - Overview Cam-Action Indexing Plungers / Indexing Plungers Cam-Action Indexing Plunger 612, Made from Steel and Stainless Steel Page 532 Page 533 Indexing Plunger 417 Indexing
More informationTHE ENCLOSURE HARDWARE SUPPLIER
FABTECH SUPPLY THE ENCLOSURE HARDWARE SUPPLIER Our Products JIC Style Enclosures JIC Style Cover Clamp Bracket... 5 JIC Style Cover Clamp... 6 JIC Style Cover Clamp Assembly... 6 JIC Cover Clamp Screws...
More informationPatio doors max. Sash width (mm) 600 to Sash height (mm) 550 to Sash weight (kg) max. 150 max. 150
ALU 5200-D (150 kg) Turn only hardware for hinge clearance (BD) 5 mm BD 5 Size range (depends on hardware) Windows min. max. Patio doors max. Sash width (mm) 600 to 1600 1300 Sash height (mm) 550 to 2000
More informationTruth Hardware (Awning Window)
Truth Hardware (Awning Window) 20-1/2" Single Pull Lever Operator Contents: 1 operator; 1 hook and 1 set of installation screws. "Y" Dimension "Y" Finish Part No. Under 2" TH-23070 Over 2" TH-23069 Under
More information09/2011 HAUTAU PRIMAT. for timber, PVC, and aluminium elements
Catalogue 09/2011 HAUTAU PRIMAT for timber, PVC, and aluminium elements HAUTAU Catalogue Fanlight openers HAUTAU PRIMAT 09/2011 HAUTAU GmbH P.O. Box 1151 D 31689 Helpsen Phone +49 05724/393-0 Fax +49
More informationNew HAZET Range of Pullers / Extractors
17 17 New HAZET Range of 2-Arm Pullers 3-Arm Pullers Hydraulic Pullers Ball Bearing Extractors Separators Internal Extractors Forged Quality Practical and Proven Tools New Innovative Range of Pullers For
More informationSection 3 LIFT SYSTEMS
Section 3 LIFT SYSTEMS LIFT FITTINGS Contents Blum AVENTOS HF 3.0 Blum AVENTOS HL 3.0 Blum AVENTOS HS 3.06 Blum AVENTOS HK 3.08 Kesseböhmer Ewiva Lift 3.1 Kesseböhmer Stay Lift 3.1 3.00 Faber cooker LIFT
More informationTelescopic Cover Support
6-170.01 Telescopic Cover Support long, steel zinc plated Telescopic Cover Support for covers and desk-leafs with automatic locking and release device. Extending the telescopic cover support completely,
More informationTOP AND CONSOLE PARTS For Models: YWED9400SW1, YWED9400SZ1, YWED9400SU1 (White/Chrome) (White/Blue) (Ultimate Silver)
TOP AND CONSOLE PARTS ELECTRIC DRYER 3 08 Litho in U.S.A. (L.T.) 1 Part No. Rev. A TOP AND CONSOLE PARTS 1 Literature Parts W10151591 Use & Care Guide W10177461 Tech Sheet W10111226 Guide, Quick Start
More informationK12 system & K12 system ADJ OPENING SYSTEMS FOR FLAP AND DROP DOWN DOORS
K system & K system ADJ OPENING SYSTEMS FOR SYMBOLS AND FINISHES LEGEND SYMBOLS = SHELF SAFELY LOCKED DURING TRANSPORTATION AND AT HOME. LOCK = ANTI-TURNOVER LOCKING SYSTEM = NORMS / PATENTS = PHILLIPS
More informationGEZE WINDOW TECHNOLOGY, NATURAL VENTILATION AND SHEV GEZE OL LINE MANUAL WINDOW CONTROLS FLEXIBLE MODULAR SYSTEMS BEWEGUNG MIT SYSTEM
GEZE WINDOW TECHNOLOGY, NATURAL VENTILATION AND SHEV FLEXIBLE MODULAR SYSTEMS BEWEGUNG MIT SYSTEM Cover photo and photo on page 2: GEZE GmbH TABLE OF CONTENTS GEZE OL Line Manual Window Control Systems
More informationSmall Tool Instruments and Data Management
Small Tool Instruments and Data Management Digital Micrometers Pages 28 34 Analogue Micrometers Pages 35 42 Special Version Micrometers Pages 43 63 External screw type micrometers accessories Pages 65
More informationLocks. Product range:
Locks Product range: Coin Locks Combination Locks Espagnolette Locks Keys Lay on Locks Locks for Metal Furniture Lock Strikers Mortise Locks Padlock Handle Pedestal Locks Removable Cylinder Locks Rim Locks
More informationAluminium Productive Fence System 40 PRODUCT CATALOGUE
11 2017 (e) Aluminium Productive Fence System 40 PRODUCT CATALOGUE solutions by F.EE Elektrotech Engineering Automation Robotik Informatik + Systeme Energietechnik F.EE GmbH In der Seugn 10 and 20 D-92431
More informationSliding Door Fittings, Roller Shutters Folding Sliding Door Fittings
Silent Fold 20/A, door weight up to 20 kg Area of application: For folding doors mounted to the carcase on one side, without running and guide track, for opening and closing the folding doors without blocking
More informationYale Revolution Window Hinge Product Overview
Page 001 Product Overview PRODUCT FEATURES Can be fitted to all standard fully reversible profiles (32mm x 12mm). Quick and easy to install in: PVC Aluminium Timber 27 module sizes covering sash heights
More informationTable of contents. Small cases:
R Firmengruppe Table of contents Small cases: Small case x-dream 418......................... III 3 Small case Tarex 419............................ III 5 Small case Profi-case 415/416....................
More informationSPARE PARTS LIST TRACTORS/RIDE MOWERS M125-94FH, , 2018
SPARE PARTS LIST TRACTORS/RIDE MOWERS M125-94FH, 967028402, 2018 ATTACHMENTS M125-94FH, 967028402, 2018 ATTACHMENTS M125-94FH, 967028402, 2018 Ref Part No Description Remark QTY KIT 1 578 17 74-02 EQUIPMENT
More informationTECHNOLOGY IN MOTION MACO. TU.-ON. and T&T FITTINGS. Comfort fittings
TECHNOLOGY IN MOTION MACO multi TU.-ON. and T&T FITTINGS Comfort fittings Installation INSTRUCTIONS 80 kg MACO Key Sash rebate height Sash rebate width Handle position Backset Maximum sash weight Comfort
More informationDESCRIPTION & OPERATION
SEATS - POWER 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Power Seats DESCRIPTION & OPERATION Power seats operate using toggle switches located on seat side. Seat adjusters are powered by a 12-volt,
More informationSeries 2000 Entrance Door Price List
Series 2000 Entrance Door Price List 02.04.2018 Hörmann United Kingdom Hörmann (UK) Limited Gee Road Coalville Leicestershire LE67 4JW Phone: 01530 513000 Fax: 01530 513001 info@hormann.co.uk Leicestershire
More informationTOP AND CONSOLE PARTS
TOP AND CONSOLE PARTS ELECTRIC DRYER 1 08 Litho in U.S.A.(LT) 1 Part No. Rev. B TOP AND CONSOLE PARTS 1 Literature Parts W10110850 Use & Care Guide W10110638 Tech Sheet W10111226 Guide, Quick Start 2 3980634
More informationINNOVATIVE MOBILITY. ATC Service Desk. Switch Refit
ATC INNOVATIVE MOBILITY Switch Refit Contents Tilt Switch Installation... 3 Pan In Limit Switch Installation... 4 Pan Out Limit Switch Installation... 5 Pan Up Limit Switch Installation... 6 Door In Limit
More informationGlass & Wooden Door Fittings
Glass & Wooden Door Fittings Product range: Door Sliders Door Track Plastic Glass Clamps Glass Door Channel Aluminium Glass Door Channel Plastic Glass Door Hinges Glass Door Locks Glass Sliding Door Systems
More informationLOCKS. Lock Cylinder and Keys. Installation. Removal. Key to Differ. Keyed Alike
PAGE 264 Lock Cylinder & Keys 265 Keys 266 Door and Drawer 270 Multi Drawer 272 Flat Multi Drawer 273 Anti Tilt 275 Double Door 276 Large Door 278 Sliding Door 278 Roller Shutter 279 Glass Door 281 Glass
More informationSTX stainless steel boxes
STX stainless steel boxes Enclosure and door manufactured from AISI 304 stainless steel (AISI 316 on request). Mounting plate manufactured from 2.5mm sendzimir sheet steel. Hinge in stainless steel. Box
More information19" chassis F. Downloads and further important information can be found on the Internet under Overview Cabinets...
Overview... 0 Cabinets... 1 19" chassis Wall mounted cases... 2 Accessories for cabinets and wall mounted cases... 3 Climate control... 4 Desk-top cases... 5 02192001 Subracks/ 19" chassis... 6 ront panels,
More informationSmart Visofold 1000 Series Bi Folding Door System
Smart Visofold 1000 Series Bi Folding Door System Smarts Visofold 1000 Series - Weather Performance BS EN 1026: 2000 Air Permeability: BS EN 1027: 2000 Water tightness: BS EN 12211: 2000 Resistance to
More informationOur passion for quality and service means we are the only brand in our market sector which offers:
Our passion for quality and service means we are the only brand in our market sector which offers: The Complete Package to the door parts, instructions, templates everything except the tools. The Codelocks
More informationLateral parallel hand Double acting. Operational stroke length: 20, 30, 40mm. 980m/s2
FH0 G G B H2 LB2 N/ S/F Specifications Size Cylinder bore size mm Actuation Working fluid Max. working pressure MPa Min. working pressure MPa Ambient temperature C Port size Operational stroke length mm
More informationDoor Hinges Concealed Hinges
Concealed mortise hinge For installation in wall recesses For flush wooden or metal doors Suitable for DIN left hand and DIN right hand Certified for fire resistant and smoke control doors in compliance
More informationEnglish 1/2015. The Profi le System
English 1/2015 The Profi le System MayTec System Technology The key to success! Solutions with Innovative Profi le The Profi le System Curved Profi les The Clean-Room System The Telescopic System The Linear
More informationDICTATOR Solutions for Sliding Doors
DICTATOR Solutions for Sliding Doors Even moving small sliding doors may implicate quite a lot of requirements: - The sliding door should close automatically, but an expensive door operator is not required
More informationConveyors 12. slide strips roller Conveyors roller elements Conveyor rollers Chain Transfer
Conveyors slide strips roller Conveyors roller elements Conveyor rollers Chain Transfer Application example conveyors Transport solutions and goods provision 1 2 3 4 5 6 7 8 362 9 1 slide strips Low-wear
More informationEA patch fittings for offset hung doors in toughened glass assemblies 56. Top centres for wood and steel frames 58. Glass preparation details 60
EA General information 50 EA patch fittings for offset hung doors, 24 mm frame stop depth EA patch fittings for offset hung doors, various frame stop depths 54 EA patch fittings for offset hung doors in
More informationPistol Grease Guns. AC475 comes complete with 4" steel extension and 4-jaw coupler with ball check AC476 comes complete with 18" flexible
Lubricating Mini Pistol Grease Guns Deluxe Single-hand-operated pistol grip Die cast grease gun head with dual discharge ports for use with steel extension as well as flexible hose Develops 3500 PSI Capacity:
More informationSUPER SUPER SUPER AUTUNNO AUTUMN 2008
SUPER AUTUNNO AUTUMN 2008 INDUSTRY SUPER valid from 01/09/2008 to 31/12/2008 available at our distributors 2 AUTOMOTIVE SUPER the new USAG offer novelties and successful products 3 WRENCHES 285 N/DS9 Code
More informationanchor winches mini genius
Horizontal Anchor Winch Mini Genius 250 anchor winches mini genius Quicks appropriately named Genius series of horizontal windlass are the epitome of Italian elegance and ingenuity working in perfect synergy.
More informationHinges. Various hinges. Stainless steel hinge with removable pin. Removable pin hinges with nylon washers. Removable pin.
Stainless steel hinge with removable pin Removable pin. Part number Material Finish Weight (g) 52-1-3877 304 stainless steel gloss 60 94.5 1.5 4 50 ø 6 ø 5 20 42 10 45 () 74.5 5.5 Removable pin hinges
More informationACCESS SOLUTIONS NEW PRODUCTS BROCHURE.
ACCESS SOLUTIONS NEW PRODUCTS BROCHURE www.essentraaccesssolutions.com ESSENTIAL SOLUTIONS DELIVERED NEW PRODUCTS Locks Hinges Gaskets Handles Stainless Steel Products Electronic p3-6 p13 14 p17-18 p7-8
More informationHS-PORTAL 300 LM Lift and slide hardware for aluminium doors Hardware information for profile manufacturers
HS-PORTAL 300 LM Lift and slide hardware for aluminium doors Hardware information for profile manufacturers... with the following benefits: with integrated night vent profile cylinder accessories secure
More informationRoller runner systems FR
Roller runner systems FR Technik für Möbel 191 Roller runner system FR 30 with one-sided captive guide rail for screw-on assembly 5 runner lengths 300-500 mm Finish: white Load capacity 55 lbs K.C.M.A.
More informationAC-20 Multi Point Actuator
29.6 (1.17) 51.1 (2.01) 29.6 (1.17) 51.1 (2.01) Cable B 52 27.3 (2.05) (.68) 27.3 (.68) 4X Ø 5.2 ± 0.1 (.210 ±.005) Cable A 29.6 (1.17) 17.3 (.68) 80.9 (3.19) 119 (4.7) (1.17) AC-20 Multi Point Actuator
More informationACCESSORIES FOR SZE2 CABINETS
ZPAS 143 DOORS Doors Intended for use instead of front solid door or rear panel. Maximum door opening angle: 120 Sheet steel textured powder paint, light grey (RAL 7035), stiffened profiles, brown smoked
More informationContents TRANSOM CLOSER 690 SERIES 23 LOCK OF GLASS DOOR 800 SERIES 24 AUTO HINGE 820 SERIES 25 PANIC EXIT DEVICE 910 SERIES 26
www.usaf.com.tw Contents ELECTRIC STRIKE 100 SERIES 1 E-SAVE SLIDER 171 SERIES 2 SHOWER HINGE 230 SERIES 3 SHOWER HINGE 240 SERIES 4 FREE HINGE 20 SERIES GLASS CONNECTOR 280 SERIES 6 PVC GASKET 290 SERIES
More informationHS-PORTAL 200 LM Lift and sliding hardware for aluminium doors Hardware information for profile manufacturer
HS-PORTAL 200 LM Lift and sliding hardware for aluminium doors Hardware information for profile manufacturer... with the following benefits: with integrated night vent profile cylinder accessories secure
More informationSPARE PARTS LIST RIDERS R214 TC, , 2015
SPARE PARTS LIST RIDERS R214 TC, 967325901, 2015 94CM CUTTING DECK R214 TC, 967325901, 2015 94CM CUTTING DECK R214 TC, 967325901, 2015 Ref Part No Description Remark QTY KIT 40 544 22 07-01 CROSS BAR 1
More informationS2005 Cabinets DESIGNERS AND MANUFACTURERS OF 19 RACK SYSTEMS
This series of Cabinets forms the basis of Australia s top selling range. They are both aesthetically pleasing and versatile. All versions of similar height and depth may be readily bayed together, further
More informationArte. Possibilities. Architecture for the future. Endless. Standard Profiles Nunc Et Orci Morbi Posuere. Arte Profiles Options. Arte Window Options
Possibilities Arte Endless Architecture for the future Standard Profiles Nunc Et Orci Morbi Posuere Arte Profiles Options Page 4 Arte Window Options Arte Door Options Page 13 Page 25 Table of Contents...
More informationLIPPERTCOMPONENTS, INC.
LIPPERTCOMPONENTS, INC. SCHWINTEK INWALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL Contents I. Controls 1-1 System components 1 1-1A versions C1 & C2 2 1-2 Motor wiring harness connections 3 1-3 Extend
More informationFlame-retardant PVC offers the protection you need.
Solid wall wiring duct Flame-retardant PVC offers the protection you need. Solid wall duct PVC Engineered to restrict wire access Constructed of flame-retardant PVC Improved flush sidewall and cover style
More informationDICTATOR Final Dampers
DICTATOR For Fire Protection Sliding Doors DICTATOR final dampers provide reliable final damping for fire protection sliding doors. The DICTATOR dampers have officially been tested for the use on fire
More informationLocks and Catches Information
Information SYMO 3000 is the worldwide unique furniture locking system from Häfele. Without tools and time-consuming installation, it provides maximum flexibility at minimum expenditure and effort. The
More informationGalley Salon Entry Felt Strip Weather Sealed Economical Versatile Precision Crafted Panels Painted Noise-isolating Rollers Quality Latches and Hardware Custom Sized Windows Flat and Knuckle Panels Single
More informationoctawall mobil A mobile wall with magnetic attraction
mobil A mobile wall with magnetic attraction exhibition systems interior design systems presentation systems cleanroom systems software and service if walls could speak - they would recommend mobil! The
More information