INNOVATIVE MOBILITY. ATC Service Desk. Switch Refit
|
|
- Magdalen Shelton
- 5 years ago
- Views:
Transcription
1 ATC INNOVATIVE MOBILITY Switch Refit Contents Tilt Switch Installation... 3 Pan In Limit Switch Installation... 4 Pan Out Limit Switch Installation... 5 Pan Up Limit Switch Installation... 6 Door In Limit Switch Installation... 7 VER: 10/9/2017
2 Tilt Switch Installation Mount new mechanical switch to H hinge as shown. Insure bracket angle will align with target dome head bolt on door hinge plate when installed. Cut and terminate the incoming switch wire, terminate black lead and use white wire to connect to new switch. Add a length of purple with white wire if needed. The switch works by grounding to the dome head bolt when the door closes. The lift out button on the remote will not operate while the switch is grounded and the door is closed. H-Hinge use this lead terminate this lead Old Magnetic Switch Existing Mag Switch Wires 2 Technical Service: (877) service@atconversions.com
3 Pan In Limit Switch Installation Mount to swing arm support as shown. Manually move the pan in and mark on the swing arm the location of where the switch contacts the swing arm. This will be the location of the target bolt. Drill and tap hole( 1/4-20) for bolt, add extra ground wire to the target bolt and connect to the out limit switch target bolt. Cut and terminate the incoming switch wire, terminate black lead and use white wire to connect to new switch. Add a length of blue with black wire if needed. The switch works by grounding to the target bolt when the pan closes. This switch can be adjusted in or out to insure pan is all the way in. Use caution not to adjust the pan in too far and cause damage. swing arm support Extra Ground (going to pan out limit switch target bolt) Technical Service: (877) service@atconversions.com 3
4 Pan Out Limit Switch Installation Mount to pan support as shown. Mount the target bolt bracket and bolt to the swing arm support as shown. Connect target bolt to extra ground wire coming from the Pan In Limit target bolt. Cut and terminate the incoming switch wire, terminate black lead and use white wire to connect to new switch. Add a length of green with black wire if needed. The switch works by grounding to the target bolt when the pan goes out. This switch can be adjusted in or out to insure pan is all the way out and clear of the floor pan, it also allows the pan to come down when actuated. Use caution not to adjust the pan out too far and cause damage. We recommend manually moving the lift in or out while installing the switch. 4 Technical Service: (877) service@atconversions.com
5 Pan Up Limit Switch Installation Mount to existing switch bracket on the lift post as shown. Manually raise the lift pan up until it stops and the hydraulics dead head. Mark the location of where the switch bolt touches the lift pan.. This will be the location of the target bolt. Drill and tap hole (1/4-20) for bolt, add extra ground wire to the target bolt, and connect to the pan in an unused area. Cut and terminate the incoming switch wire, terminate black lead, and use white wire to connect to new switch. Add a length of pink with black wire if needed. The switch works by grounding to the target bolt when the lift pan is up. This switch can be adjusted up or down to insure pan is all the way up. Insure pan is up enough not to contact the floor pan and just touches the dry slide. existing bracket Technical Service: (877) service@atconversions.com 5
6 Door In Limit Switch Installation Mount to swing arm support as shown. Manually close the door and mark the location of where the switch contacts the door. This will be the location of the target bolt. Drill and tap hole (3/8 16) for switch target bolt. Cut and terminate the incoming switch wire, terminate black lead and use white wire to connect to new switch. Add a length of purple with black wire if needed. The switch works by grounding to the target bolt when the door closes. This switch can be adjusted in or out to insure door is closed all the way in. Use caution not to adjust the door in too far and cause damage. swing arm support ground target bolt on door 6 Technical Service: (877) service@atconversions.com
OFFICE PARTITIONS. Data Port Openings. Use cable tie bracket to dress data cables under panels. STEP 1
N Power Box Opening Data Port Openings Rear View Front View Remove opening blanks on raceway cover for power and data. If panel contains no electric or data and is used as a pass-thru, leave opening blanks
More informationTS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH)
Surface applied door closer Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) TABLE OF CONTENTS Technical specifications Size selection chart 2 Closer setup
More informationBrake and Tail Light Kit Workman 1100/2100 and Twister Utility Vehicles
Form No. 5-90 Brake and Tail Light Kit Workman 00/00 and Twister Utility Vehicles Part No. 0 6697 Installation Instructions Important Before installing this kit, you must have Wiring kit number 99 79 installed
More informationCASRE Disconnect Arm Retro Instructions 2/23/2016
CASRE Disconnect Arm Retro Instructions 2/23/2016 Existing Part Removal W Instructions 1. Turn off incoming power to fan disconnect. 2. Turn off fan disconnect switch and flip up disconnect arm. 3. Remove
More information2003 Chevrolet Impala LS
MULTIFUNCTION, TURN SIGNAL SWITCH REPLACEMENT Removal Procedure Fig. 28: View Of Steering Column Wire Harness Assembly & Wire Harness Strap CAUTION: Refer to SIR Caution in Cautions and Notices. Tuesday,
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION 0 F LOW AMBIENT ACCESSORY MODELS 2LA04703425, 3546 & 3658 (208, 230, 460 & 575 VOLT APPLICATIONS) Supersedes: 530.18-N5.6V (1091) 530.18-N5.6V (1193) FOR 15, 20 & 25 TON COOLING
More informationIntelligent Lift Interlock ILISCT511-A (Manual Lift Door) Ford Transit Connect
An ISO 9001:2000 Registered Company Intelligent Lift Interlock ILISCT511-A (Manual Lift Door) 2010-2013 Ford Transit Connect Introduction The ILISCT511 is a microprocessor driven system for controlling
More informationHunter Automatics HA-8. Installation Manual
Hunter Automatics HA-8 Installation Manual WARNING TO REDUCE RISK OF INJURY 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY. FAILURE TO DO SO MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE
More informationINNOVATIVE MOBILITY ATC CUV TROUBLESHOOTING GUIDE. Shipping/Mfg. Location 4654 East Markle Road Markle, IN
ATC INNOVATIVE MOBILITY ATC CUV TROUBLESHOOTING GUIDE Shipping/Mfg. Location 4654 East Markle Road Markle, IN 46770 service@atconversions.com ATC provides a life-changing experience through mobility with
More informationElectronic Entry Device Installation Instructions
Electronic Entry Device Installation Instructions for basic and gard series Table of Contents General Information... 1 Entry Device Mounting Templates... 3 3000 and 3715 Entry Device... 4 3035 & 3125 Round
More informationSide Channel Mag Drive (SCM) Assembly
Side Channel Mag Drive (SCM) Assembly Side Channel pumps are available with a magnetic drive option. The pump or fluid end remains the same as the mechanical seal pump for repairs. SCM Pumps Pumps all
More informationKT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump
KT101 Series Governor System Installation Kit Cummins 4B(T) / 6B(T) With CAV/DPA Pump 30 Years Strong! Introduction The KT101 Series Governor System Installation Kit provides the necessary brackets and
More informationMag-Hytec. Installation Recommendations FORD 4R100 / E4OD TRANSMISSION PAN
Mag-Hytec Installation Recommendations FORD 4R100 / E4OD TRANSMISSION PAN 07/08/17 Please read these instructions and parts list completely before installing this new transmission pan. Consult your owner
More informationINSTALLATION INSTRUCTIONS
Series 2001 Belt Drive Slide Door & RapidSlide INSTALLATION INSTRUCTIONS To be used with H202 C2150 Ver.2 Control Setup Instructions G2001, FEB 2004 CONTENTS 1. Instructions to installer... G2001.1 2.
More informationJK8 Body Kit KIT CONTENTS 1 K
JK8 Body Kit KIT CONTENTS A B C 1 K6861352 D E G F H 2 K6861352 I M N J K L O P Q R S 3 K6861352 T U V W X Y CALL OUT PART NUMBER DESCRIPTION QUANTITY A P5156021 HARDTOP 1 B P5155997 BULKHEAD 1 C 1PH98/9TZZAE
More information!!!! ! Lock housing dimensions: 230mm L x 44mm W x 44mm D! Receptacle housing dimensions: 120m L x 44mm W x 44mm D. ! Surface mount housing for LK120
ELECTROMAGNETIC LK120 Bolt Action Lock SP (Fail Safe) Fail-Safe: Strike Plate: Bolt Stainless Steel: 200(L) x 32(W) x 40(D) mm 90(L) x 26(W) x 2(D) mm 15.5mm Diameter, 17mm Throw 12V Operation Operation
More informationStrip Fixture URS Light Bar Retrofit Installation Instructions Revised:
Strip Fixture URS Light Bar Retrofit Installation Instructions Revised: 20180126 These instructions do not purport to cover all details or variations in components nor to provide for every possible contingency
More informationInstallation Guide. Electronic Entry Device. LA GARD Basic & Gard Series
Installation Guide Electronic Entry Device Document Number 762.128 Rev. F 03 / 2017 LA GARD Basic & Gard Series Table of Contents 1 General Information 2 Entry Device Mounting Templates 3 3000 and 5715
More informationKT145 Series John Deere 6076 with Nippondenso Inj. Pump
KT145 Series John Deere 6076 with Nippondenso Inj. Pump 30 Years Strong! Introduction The KT145 Series Governor System Installation Kit provides the necessary brackets and hardware to install a GAC precise
More informationCHEVORLET IMPALA
1962-64 CHEVORLET IMPALA Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 deck lid harness 4 grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN
More informationOpening Quality Doors Around The World. Installation Instructions Bi-Parting Freight Doors - Q Style (Power and Manual)
Opening Quality Doors Around The World www.couriondoors.com Installation Instructions Bi-Parting Freight Doors - Q Style (Power and Manual) Table of Contents For Immediate Help Call 1-800-533-5760 Q Style
More informationELECTRONIC ENTRY DEVICE INSTALLATION INSTRUCTIONS FOR BASIC AND GARD SERIES
ELECTRONIC ENTRY DEVICE INSTALLATION INSTRUCTIONS FOR BASIC AND GARD SERIES TABLE OF CONTENTS GENERAL INFORMATION... 1 ENTRY DEVICE MOUNTING TEMPLATES... 3 3000 AND 3715 ENTRY DEVICE... 4 3035 & 3125 ROUND
More informationCTN U-TYPE DIE COLOR INDEX QTY 7/374 8/346 11/375 12/ /298 18/324 19/470 20/299 22/472 24/473 CTN U-TYPE DIE COLOR INDEX QTY
PAGE 2 PEEP HOLE STANDARD BARREL COPPER LUGS Allows inspection of the termination to assure complete cable insertion GL SERIES One-Hole 32000 GL 80 32002 GL 84 3999 GL 0 32004 GL 4 3200 GL 5 32003 GL 38
More informationKT230 Series Caterpillar 3406 Governor System Installation Kit
KT230 Series Caterpillar 3406 Governor System Installation Kit 30 Years Strong! Introduction The KT230 Series Governor System Installation Kit provides the necessary brackets and hardware to install a
More informationB CW POWER RELAY
41-241.31B CW POWER RELAY nected in such a way that current, (I A ), leads voltage, (V BA ), by 150 degrees when the motor is operating at unity power factor. Loss of excitation to the motor causes a large
More informationTS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall)
TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall) TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer
More informationSolenoid valve. Solenoid Coil
Solenoid valve Solenoid valve Solenoid Coil Plunger Valve body A simple solenoid valve consists ofi: Valve body with a plunger the plunger is made of metal Coil an electrical coil if the coil is given
More informationInstallation Instructions For Motor Control Center (MCC) Units
s Page 1 of 8 Installation Instructions December, 2013 Installation Instructions For Motor Control Center (MCC) Units Hazardous voltage. Will cause death or serious injury. Always de-energize and ground
More informationUSER MANUAL. Item: #13246 Stand-Aid Lift. Drive Medical Design and Manufacturing Push Handle. Base Width Adjustment Handle.
USER MANUAL Item: #13246 Stand-Aid Lift Push Handle Base Width Adjustment Handle Mast Sling Attachment Hook Adjustable Knee Pad Front Caster W/Brake Foot Plate Front Caster W/O Brake Rev1.06.11.14 IMPORTANT
More informationSelf-Deploying Rail Kit OEM INSTALLATION MANUAL
Self-Deploying Rail Kit OEM INSTLLTION MNUL TLE OF ONTENTS Introduction 2 Safety Information 2 Resources Required 3 Prior to Installation 3 Installation 3 Doorjamb 3 Setting the Doorjamb 3 inch Latch 4
More informationPower In - Pathways Technology Wall
Power In - Pathways Technology Wall NOTE: With an off module application involving the transition of cabling or electrical harnesses, you will have to drill a maximum of a 2-1/2" hole in the beltway trim
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS LB20 SERIES RAMPS Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4868 Fax (712) 722-4779 QUESTIONS? CALL CUSTOMER SERVICE 1-800-248-3057 www.linkmfg.com
More informationMSD Blaster Ignition PN 5900
MSD Blaster Ignition PN 5900 Note: Read these instructions completely before attempting any installation. Parts Included: 1 - Blaster Ignition, PN 5900 1 - Harness, PN 8860 1 - Harness, PN 8861 1-18" Ground
More informationLOW MOUNT SPA COVERLIFT Installation Instructions
LOW MOUNT SPA COVERLIFT Installation Instructions IMPORTANT!! READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION ITEM NUMBER: NP5022 Mfg#3200103 (Spa and Spa Cover Not Included)!! CAUTION!!
More informationR-SE JK 4 DOOR Step Slider Install Instructions. *If any parts listed are missing or damages please call prior to install.
R-SE JK 4 DOOR Step Slider Install Instructions Parts List: 1 Divers side slider assembly 1 Passenger side slider assembly 1 wiring harness 1 control box 2 spacers 2 LED lights (optional) 10 SS Button
More informationTURN-TiLT WiNDOWs A11.16 CHRONO ACCessORies
A11 TURN-TILT WINDOWS A11.16 CHRONO Accessories 01.02.2014 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com Contents 1. Window stay
More informationFeeder Circuit Breaker Units Secure Support Pan and Change Door Latch
Installation Instructions Feeder Circuit Breaker Units Secure Support Pan and Change Door Latch Catalog Numbers 2193FZ Topic Page About This Publication 1 Required Tools 1 Important User Information 2
More informationSAFETY REASONABLE EFFORT. ANY BINDING, SAGGING, LOOSE HINGES, OR DAMAGED HINGES MUST BE REPAIRED BEFORE CONTINUING WITH THIS INSTALLATION!
Commercial Gentleman Door Operator Installation Instructions SAFETY THE COMMERCIAL GENTLEMAN IS A LOW ENERGY DOOR OPENER. PROPERLY ADJUSTED, THIS OPENER SHOULD BE EASY TO STOP WITH YOUR LITTLE FINGER.
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More informationMIC210 Electric Farm Conversion Instructions
MIC210 Electric Farm Conversion Instructions Note: Apply the supplied Dielectric Lubricant to all wire connections when each wire is hooked up. The Dielectric Lubricant will help to prevent corrosion.
More informationCAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT
Page 1 of 45 CAMSHAFT TIMING CHAIN, SPROCKET, AND TENSIONER REPLACEMENT Special Tools J 45027 Tensioner Tool J 45059 Angle Meter Page 2 of 45 Removal Procedure Page 3 of 45 Page 4 of 45 Page 5 of 45 Fig.
More informationDEMA 652 DUO-FEED INSTALLATION INSTRUCTIONS
I. PARTS: A. Dispenser assembly B. 1 pc. ½ in I.D. X 6 ft. vinyl outlet tubing C. 1 pc. 9/16 in. I.D. X 6 ft. vinyl outlet tubing. D. 2 pc. 3/8 in. O.D. X 8 ft. vinyl supply tubing, foot valve & ceramic
More information2001 Dodge Dakota ENGINES 4.7L V8
FRONT COVER Removal & Installation 1. Disconnect negative battery cable. Remove drive belt. Remove A/C compressor mounting bolts, and position compressor aside. Drain cooling system. Remove radiator hoses.
More informationSHIELDS COMPANY PERMANENT MAGNETIC TOW SWEEPER MODEL MKS4000
SHIELDS COMPANY PERMANENT MAGNETIC TOW SWEEPER MODEL MKS4000 The MKS4000 MAGNETIC TOW SWEEPER is the most effective and most durable permanent magnetic sweeper available. Its super powered magnets insure
More informationInstallation Instructions QUARTER STICK Fits: 2 Speed (Powerglide) or 3 Speed (Turbo-Hydramatic)
Installation Instructions QUARTER STICK Fits: 2 Speed (Powerglide) or 3 Speed (Turbo-Hydramatic) Catalog# 3160020 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and
More informationTS93 EMF T/PT/TDE. Surface applied door closer
TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress
More informationCar Gate - Ratio Installation Instructions.
The Next Generation of Freight Elevator Doors www.couriondoors.com Car Gate - Ratio Installation Instructions For Immediate Help Call 1-800-533-5760 CAR GATE - Ratio TABLE OF CONTENTS Check Car Enclosure
More informationOPERATING INSTRUCTIONS
2 7 5 OPERATING INSTRUCTIONS PORTABLE PART NO. 28357 By functioning as a triggering device, Mallory's Portable Ignition Tester allows you to check the operation of a car s ignition system without starting
More informationTwo Function Remote Control System (Model RC192)
Golden Rodtronics P.O. Box 146 Golden Colorado 80402-0146 Phone 303-423-8597 Fax 303-420-4575 Two Function Remote Control System (Model RC192) Congratulations! You have just purchased one of the finest
More informationINSTALLATION INSTRUCTIONS FOR PART TRIGGER TRIGGER
6 2.5 1.5 ISO M4 M5 M3 WIRE CUTTER INSTALLATION INSTRUCTIONS FOR PART TRIGGER TRIGGER The Trigger is a universal module that provides 15 different preset functions that are activated from a positive or
More informationMustang. Installation Manual. Revision 11/16/10
1967-1968 Mustang Installation Manual Revision 11/16/10 I Table of Contents TABLE OF CONTENTS...II WELCOME TO THE TEAM OF CLASSIC INSTRUMENTS!... III REMOVE ORIGINAL INSTRUMENT PANEL...1 DETERMINE SPEEDOMETER
More informationPD10-M-RIM INSTALLATION INSTRUCTIONS. The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction.
PD10-M-RIM INSTALLATION INSTRUCTIONS The PD10-M-RIM is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrofits Doromatic 1790 & First Choice 3790. B. G. A. C. D. E. F. PD10-M-RIM
More informationTable of Contents. 1.0 INFORMATION 1.1 Introduction. 1.2 Product Information. 2.0 INSTALLATION 2.1 Pre-Installation. 2.2 Component Installation
Contents Table of Contents 1.0 INFORMATION 1.1 Introduction 1.1.1 About This Manual 1.1.2 Helpful Hints and Warnings 1.1.3 Service and Product Support 1.2 Product Information 1.2.1 System Components 2.0
More information= Experienced
I N S T A L L A T I O N G U I D E APPLICATION LENGTH MODEL YR PART # Ford F-250 / F-350 / F-450 Regular Cab * (48 ) 2002-2003, 2008-2016 75134-01A Ford F-250 / F-350 / F-450 Super Cab * (60 ) 2002-2003,
More informationElectric Lock Part List
When the length of your gate is more than 1.5 meters, we recommend installing an Electric Lock. An electric lock provides extra security and stability to your gate system. The lock provides extra protection
More informationFord F150 SuperCab Ford F150 SuperCrew
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Ford F150 SuperCab 7 00-007 10-0996-11 Ford F150 SuperCrew 79 00-007 10-0996-1 INSTALLATION TIME 3:00 hrs SKILL LEVEL 1 3 = Experienced TOOLS REQUIRED
More informationInstallation Instructions for the Plug & Play Remote Start Package (EVOCHR5)
T6018 v1.1 02/2013 Installation Instructions for the Plug & Play Remote Start Package (EVOCHR5) For DODGE Nitro 2007-2011 Review the remote start installation manual for safety instructions! Overview Your
More informationStorage Basket and Clamp Vertical Oxy Holder and Clamp Pogo IV Pole / Stand - Heavy Base Provita Smart IV Stand IV Handle and Clamp
This range of equipment is engineered for strength and durability to withstand continuous use year after year. A blend of different materials and finishes are used throughout the range. All products are
More informationSWING DOOR SOFT ENCLOSURE (part# 16733)
800-643-7332 americanlandmaster.com This kit is for use with all fullsize, 2 passenger ALM utility vehicles. SWING DOOR SOFT ENCLOSURE (part# 16733) NOTE TOOLS REQUIRED Drill 1/4 Drill Bit 7/16 Wrench
More informationInstallation Instructions Lockey TB 250/450/650 Plus Hydraulic Pedestrian Gate Closer (with hydraulically adjustable closing speed)
Installation Instructions Lockey TB 250/450/650 Plus Hydraulic Pedestrian Gate Closer (with hydraulically adjustable closing speed) The Lockey TB 250/450/650 Plus Pedestrian Gate Closer is a fully featured
More informationUSER MANUAL. Item: #13246 Stand-Aid Lift. Drive Medical Design and Manufacturing
USER MANUAL Item: #13246 Stand-Aid Lift IMPORTANT SAFEGUARDS Your lift is for transferring patients only. Do not use the lift for any other purpose. Stand-Aid Lift is intended to be used for persons within
More information655 South Lincoln Avenue / San Bernardino CA Phone / Fax / Web address: globalwest.net
655 South Lincoln Avenue / San Bernardino CA. 92408 Phone 877-470-2975 / Fax 909-890-0703 / Web address: globalwest.net Part # TBC-9 or TBC-10 --- 1963-82 Corvette Rear swing arm installation instructions:
More informationINSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Ford F150 SuperCab * 72 200-2008 75105-01A Ford F150 SuperCrew 79 200-2008 75105-01A *Modifi cation required to running board assembly. See Item 1
More informationHandy Lift LT Owners Manual
Installation and Operating Instructions - Service and Parts Information BURR 300 lb. Capacity Handy Lift LT PN 33170 (40 ) PN 33171 (45 ) PN 33172 (50 ) Avoid serious injury, or death, to yourself and
More informationSPACESAVER EC-300 A ELECTRICS
INSTALLATION INSTRUCTIONS SPACESAVER EC-300 A ELECTRICS SECTION I TOP MOUNTED ELECTRICS SECTION II FACE PANEL MOUNTED ELECTRICS SECTION III ZFS INSTALLATION INSTRUCTIONS This symbol indicates a connection
More informationHomebrew Travel Antenna
Homebrew Travel Antenna This is a low cost homebrew two band travel antenna for 20 and 40 meters. It is based on the B&W Travel Antenna concept with a telescoping whip and a loading coil. A piece of 1/8
More informationBUICK SKYLARK & GS CHEVROLET CHEVELLE & MONTE CARLO PONTIAC GTO & LEMANS OLDSMOBILE CUTLASS & 442
28433 HWY 65 NE ISANTI, MN 55040 763-444-5880 800-828-2212 www.autocityclassic.com 1970-1972 GM A-BODY 2DR COUPE, INSTALLATION HARDTOP & CONVERTIBLE INSTRUCTIONS POWER WINDOW INSTALL KIT BUICK SKYLARK
More information7100SZ Series SafeZone Installation and Instruction Manual
7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 80-9371-0081-00 (10-10) Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 5 for template) 3 1 Push Side Applications
More informationUNIVERSAL PRODUCTION EDGE BELT SANDERS
UNIVERSAL PRODUCTION EDGE BELT SANDERS Designed for use with edge finishing devices common to the furniture and custom woodworking industry. The ability to use the machine for a variety of edge finishing
More informationConversion Kit for HP1200 Cartridge
OEM HP1200 (C7115A) Cartridge Conversion Using T.P.E. CC1197 Canon EP26/EP27/X25/U Type Conversion Kit for HP1200 Cartridge OEM HP1200 (C7115A) T.P.E. CC1197 Canon EP26/EP27/X25/U Type Conversion Kit for
More informationSLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92
Page 1 of 5 SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & #09-10 1988 & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET #09-9 (For stock
More informationDfuser T/C Lock Override with LED
Dfuser T/C Lock Override with LED the bug that has no cure For more information visit our website at: http://www.dfuser.com Page 1 of 7 User Guide This harness overrides and monitors Torque Converter (T/C)
More informationMSD 7AL-3, Ignition Control PN 7230
MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,
More informationNECO Pumping Systems
INSTALLATION OPERATION & MAINTENANCE INSTRUCTIONS For Your NECO Pumping Systems PACKAGED CIRCULATING SYSTEM THIS COMPLETELY ASSEMBLED, TESTED, PACKAGED CIRCULATING SYSTEM IS OF THE HIGHEST QUALITY AND
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationHandy Lift HD Owners Manual WARNING. BURR 500 lb. Capacity Handy Lift HD PN (40 ) PN (45 ) PN (50 )
Installation and Operating Instructions - Service and Parts Information BURR 500 lb. Capacity Handy Lift HD PN 32689 (40 ) PN 33145 (45 ) PN 33056 (50 ) Avoid serious injury, or death, to yourself and
More information3-5 Hours Professional installation recommended
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Nissan Titan / Titan XD - Crew Cab 72 2016-2018 76120-01A Nissan Titan / Titan XD - King Cab 62 2017-2018 76120-01A Nissan Titan / Titan XD - Single
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationGateCrafters Automatic Gate Lock Instruction Manual GCLOCK
GateCrafters Automatic Gate Lock Instruction Manual GCLOCK Introduction The GateCrafters Automatic Gate Lock is designed to provide extra security and stability to your gate opener system. There are numerous
More informationREAD AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Installation Instructions RT8RT/RT5RT Relight Assembly READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION. IMPORTANT SAFETY INSTRUCTIONS WARNING: FAILURE
More informationThree Function Remote Control System with Alarm (Model RCA-3)
Golden RODtronics P.O. Box 146 Golden Colorado 80402-0146 Phone 303-423-8597 Fax 303-420-4575 Three Function Remote Control System with Alarm (Model RCA-3) Congratulations! You have just purchased one
More informationCastle Model TSM-21 Standard Screw Pocket Machine
Castle Model TSM-21 Standard Screw Pocket Machine "For Models with Serial Number 62481 and Above" Items Included with Machine Part No. Description Qty B00964 Castle 9/64 Cobalt Drill Bit w 1/4" Shank 1
More informationWIRE SYSTEM PRO15 ULTRA SMALL 15 FUSE 24 CIRCUIT 118 TERMINAL PANEL WIRE SYSTEM
TECH UPPORT: 503.693.1918 WIRE YTEM WWW.KEEPITCLEANWIRING.COM PRO15 ULTRA MALL 15 FUE 24 CIRCUIT 118 TERMINAL PANEL WIRE YTEM IMPORTANT: The below instructions are referring to a general installation.
More informationACCEL/DFI 6A Sportsman Electronic Ignition Control Module for Distributor Equipped Engines
INSTALLATION INSTRUCTIONS FORM 1522D 3/08 REV. 13 ACCEL/DFI 6A Sportsman Electronic Ignition Control Module for Distributor Equipped Engines PARTS INCLUDED: PART NO. 75606 1 Ignition Control Module 5 1/4"
More informationC3000 SIGNAL TRANSMITTER. Introduction
C131-05, Page 1 952-361-3026, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 C3000 SIGNAL TRANSMITTER Introduction The MAXIGARD C3000 series is designed to convert shaft
More informationKOMBI 3 OPERATION. Fleet Line Markers Ltd PREPARING THE KOMBI 3 FOR USE
KOMBI 3 OPERATION PREPARING THE KOMBI 3 FOR USE 1. Carefully remove the Kombi 3 and accessories from packaging. 2. Charge the battery using the supplied charger. CAUTION. Only use the supplied charger.
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationLumenition Optronic Ignition System PMA 50 Power Module. Fitting Instructions
Not for use on low-resistance electronic coils. Fitting Instructions Read carefully all sections before proceeding with any fitting. How It Works Lumenition Optronic Ignition is an electronic ignition
More informationB2000 SERIES TACHOMETERS DIGITAL OR ANALOG DISPLAYS
B133-05, Page 1 952-361-3026 PROCESS CONTROL SYSTEMS, INC. (Fax) 952-368-4129 327 LAKE HAZELTINE DRIVE, CHASKA, MN 55318 800-328-0738 B2000 SERIES TACHOMETERS DIGITAL OR ANALOG DISPLAYS Introduction The
More informationSTYLE 9300 FLOW/PRESSURE METER INSTALLATION & OPERATING INSTRUCTIONS
STYLE 9300 FLOW/PRESSURE METER INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION The Style 9300 Flow/Pressure Meter from Akron is designed to offer reliable and accurate service with an easy to install,
More informationGAS CONVERSION KIT INSTALLATION INSTRUCTIONS
GAS CONVERSION KIT INSTALLATION INSTRUCTIONS These instructions apply to the following gas conversion kits: 8261139 8261140 8261141 8261142 8261143 8261144 8261158 8261747 8261748 8261964 8261965 8263059
More informationCOYOTE 9.5" x 19" (292 mm x 509 mm) Cross-Connect Dome Closure
AUGUST 2013 COYOTE 9.5" x 19" (292 mm x 509 mm) Cross-Connect Dome Closure Be sure to read and completely understand this procedure before applying product. Be sure to select the proper PREFORMED TM product
More informationHinge technology for face frame cabinetry: Optimat
Hinge technology for face frame cabinetry: Optimat Face-frame hinge Optimat 3E Hinge technology for face frame cabinetry Made in USA Meets and exceeds the minimum requirements of ANSI/BHMA A156.9 Nine
More informationDC3210 Series. Multi-Sized 1 thru 6 DEEP REVEAL APPLICATION WITH M103 OPTION(615F59 CLAMP KIT) Recommended Closer Size
DC310 Series Multi-Sized 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH DEEP REVEAL APPLICATION WITH M103
More informationWARNING! THIS SHIFTER IS FOR RACING USE ONLY. NOT FOR STREET USE!
Installation Instructions Quarter Stick Shifter Fits: GM Powerglide w/forward or reverse valve body. Also fits: TH250, TH350, TH375 and TH400 Auto transmissions w/reverse valve body. Catalog# 3162020 WORK
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. Tel 775.355.5625 550 Vista Boulevard Fax 775.355.5633 Sparks, NV 89434 info@securitron.com www.securitron.com ASSA ABLOY, the global leader in door opening solutions INSTALLATION
More informationHYFIRE 6AL2 ELECTRONIC IGNITION CONTROL
INSTALLATION INSTRUCTIONS FORM 1643 HYFIRE 6AL2 ELECTRONIC IGNITION CONTROL PART NO 6861M PARTS INCLUDED: 1 HYFIRE 6AL2 Ignition Control 4 #10 Sheet Metal Screws 2 Wire Ties 2 Ring Terminals, Insulated
More informationMagnetic Door Jamb Switches (Ground Style) Installation Instructions
2501 Ludelle Street Fort Worth, Texas 76105 817-244-6212 Phone 817-244-4024 Fax 888-350-6588 Sales 800-423-9696 Tech E-mail: painless@painlessperformance.com Web: www.painlessperformance.com 80180 Magnetic
More information