SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92
|
|
- Janice Ray
- 5 years ago
- Views:
Transcription
1 Page 1 of 5 SLP PIPE INSTALLATION INSTRUCTIONS #09-9 & # & NEWER POLARIS INDY 650 & RXL PIPE SET EFFECTIVE 6-92 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET #09-9 (For stock engine, RXL* or carbureted) "S" marked on headpipe. #09-10 (for trail ported engines with carbs only) "P" marked on headpipe. NOTE: *RXL MODEL must be used with the #70-G90 Clicker Chip to reprogram the EFI for the pipe set. Failure to do so could cause engine failure and/or poor performance. A. Reverse kit cannot be used with the triple pipe set. B. It is best to check ignition timing and adjust if needed before removing stock exhaust system. If adjustment is needed, the best time to remove the recoil for adjustment is when the stock exhaust system is removed. INSTALLATION INSTRUCTIONS 1. Remove standard muffler, silencer, and "Y" pipe from the sled. Retain exhaust gaskets, nuts, and springs. Remove rear muffler support bracket. Remove stock belly pan outlet by drilling out pop rivets and retain this part to be installed in a new location. NOTE: Before installing pipes, it is recommended to cut with a hole saw the four 1½" holes in the plastic behind the nose cone to improve air flow for improved performance. 2. Install three exhaust flanges on cylinders with the original gaskets and nuts. Cover original outlet hole with flat aluminum plate provided with kit. Install the MAG and PTO heat shields. NOTE: For best pipe fit, the MAG heat shield must fit the contour of the shock tower. This shield can be shaped easily by pushing it into the shape of the top of the shock tower. 3. Install the MAG pipe first, silencer assembly second, PTO pipe third, and the CENTER pipe last. Mark for the new exit hole, remove pipes, install original outlet plate in the new location using the 3/16" steel pop ribets provided. Reinstall pipes. IGNITION TIMING IGNITION TIMING - For best performance and dependability, the ignition timing must be correct on any snowmobile. Occasionally the timing is not correct from the factory or it can change slighty with time and miles. Use the following timing specification for the models listed. NOTE: the high RPM timing, this specification is the most important since the engine is run in that area most. If the low RPM timing si off slightly it will still perform well. Timing marks on the flywheel should be checked with a dial indicator to insure accuracy. Occasionally the marks are not correct. By using a high RPM strobe type timing light (see SLP catalog tool section)
2 Page 2 of 5 the timing can be checked on the flywheel or clutch stationary sheeve by using dial to make marks. CAUTION! WHEN USING MARKS ON STATIONARY SHEEVE OF THE ENGINE CLUTCH, ENGINE CLUTCH COVER MUST BE LOCKED IN PLACE WHEN THE ENGINE IS RUNNING! It is best to rune engine with belt removed, clutch cover locked in place, then gently throttle up to test RPM INDY 650 (01 ENGINE) 27 degrees at 3000 RPM ±2 degrees, 20 degrees at 7500 RPM ±½ degree & NEWER RXL &CARBURETED INDY 650 (02 ENGINE) 24 degrees at 3000 RPM ±2 degrees, 18 degrees at 7500 RPM ±½ degree INDY 650 (03 ENGINE) 25 degrees at 3000 RPM ±2 degrees, 19 degrees at 7500 RPM ±½ degree. CARBURETOR TUNING IMPORTANT NOTES: (For RXL information, refer to instructions included with the SLP/Chopper City Clicker Chip #70-G90.) 1. The following carburetor specifications are a beginning point only, due to your particular use and atmosphere, jetting may need to be slightly richer or leaner. Always start rich and lean it down step by step to get exact jetting. 2. The following specifications are for use with the air box in place with either of the options listed. Removing the air box requires richer main jets and needle jets to prevent lean mixture burn down. 3. SLP recommends the use of exhaust gas temperature gauges (EGT) for precise carb tuning. See the SLP catalog for optional gauges. 4. Some 650 models come equipped without the 6DH4 needle. Inspect the needle number your sled is equipped with and change to the 6DH4 if needed. NEEDLE CLIP POSITION - The last digit in the tuning spec is the clip position. Such as 6DH4-3, the "3" would be the third clip form the top (top position being #1). OPTION #1: Stock air box with foam removed with plastic plate retained and in place. The plastic plate will keep intake noise at a lower level. A. Stock 38 m/m round slide carbs. TEMPERATURE ALT. -40 to to 0 0 to to to ' ' '
3 Page 3 of 5 B. Bored stock carb to 39.2 m/m. One step richer main jet than above chart and one needle clip position richer. OPTION #2: Stock air box with foam and plastic plate removed. A. Stock 38 m/m round slide carbs ' ' Sea Level to 5000' 5000' and higher Pilot Jet - 45 Pilot Jet - 45 Slide or 2.5 Slide or 2.5 Needle - 6DH4-3 Needle - 6DH4-3 Needle Jet - Q2 Needle Jet - P8 TEMPERATURE ALT. -40 to to 0 0 to to to ' ' ' ' ' Sea Level to 5000' 5000' and higher Pilot Jet - 45 Pilot Jet - 45 Slide or 2.5 Slide or 2.5 Needle - 6DH4-3 Needle - 6DH4-3 Needle Jet - Q2 Needle Jet - P8 B. Bored stock carb to 39.2 m/m. One step richer main jet than above chart and one needle clip position richer. EXHAUST TEMPERATURE READINGS Specifications are for use with SLP gauges and probes. Follow instructions with gauge kit mounting. The temperature readings are for use with SLP triple pipe set with probe mounted within 6-8" from exhaust flange gasket. 1/4 throttle, degrees 1/2 throttle, degrees 3/4 throttle, degrees Full throttle, degrees
4 Page 4 of 5 With the engine water at running temperature, begin with low throttle settings first. It is best to run about 1/8th mile or more to stabilize EGT for your reading. Adjust low and midrange with the needle clip position to achieve proper temperature and throttle response. When the midrange is tuned continue with full throttle jetting in the same manner. Never test full throttle position first, if midrange is lean it could cause a deceleration siezure. CLUTCH TUNING NOTE: Due to different riding conditions and riders weight, it may be necessary to use lighter or heavier weights or springs to tune RPM to the proper peak running area. The following tuning specifications are the average for each altitude listed. Tuning parts are available from SLP. LOW ALTITUDE: ' Weight Arm - 10M Blue (47.5 gram) # Driven spring average setting - #2 hole, increase if needed HIGH ALTITUDE: 5000' & ABOVE Weight Arm - 10M Red (44 gram) # Driven spring average setting - #3 hole, increase if needed OPTIONAL LOW ALTITUDE CLUTCHING Weight Arm - 10M White (46 gram) # Helix - 40/36 multi-angle, SLP #40-40/36 Driven spring - Dark Purple, SLP #40-1, begin in hole #3 GEARING Suggested gearing with the SLP trail pipes for general purpose is 20 tooth top sprocket and 35 tooth bottom sprocket. Or a 22 tooth top sprocket and a 39 tooth bottom sprocket to achieve a similar ratio. For speed run or fast lake racing a larger top sprocket can be used. for deep snow or hillclimbing.
5 Page 5 of 5 ILLUSTRATIONS Starting Line Products, Inc. (208) slp@slp.cc
XLT SPECIAL TRIPLE PIPE SET P.N Installation Instructions
1995-97 XLT SPECIAL TRIPLE PIPE SET P.N. 09-598 Installation Instructions Revised 8/20/02 Read instructions carefully before installation 1 - Remove stock exhaust, Y-Pipe, front and rear muffler support.
More informationXCR 600/ XLT TRIPLE PIPE SET P.N Installation Instructions
1994-97 XCR 600/1993-97 XLT TRIPLE PIPE SET P.N. 09-5970 Installation Instructions Read instructions carefully before installation 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three
More informationPOLARIS XLT 580/600 INSTALLATION INSTRUCTIONS PART # READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET
Page 1 of 6 POLARIS 1993-97 XLT 580/600 INSTALLATION INSTRUCTIONS PART #09-595 READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL PIPE SET 1. Remove stock exhaust, y-pipe, front and rear muffler
More informationSLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.
SLP PIPE INSTALLATION INSTRUCTIONS POLARIS 1996-97 ULTRA 680 SP SKS & RMK P.N. 09-6802 (Read instructions carefully before installation.) NOTE: The Ultra has proven to exhibit distinct personalities from
More informationPOLARIS XLT-SPECIAL TRIPLE PIPE SET P.N
1998-99 POLARIS XLT-SPECIAL TRIPLE PIPE SET P.N. 09-596 Important: Read instructions carefully before installation. 1-Remove stock exhaust, Y-pipe, and rear muffler support. 2-Install three exhaust flanges,
More informationSLP PIPE INSTALLATION INSTRUCTIONS POLARIS ULTRA 680 SP SKS & RMK P.N (Read instructions carefully before installation.
SLP PIPE INSTALLATION INSTRUCTIONS POLARIS 1996-97 ULTRA 680 SP SKS & RMK P.N. 09-6801 (Read instructions carefully before installation.) NOTE: The Ultra has proven to exhibit distinct personalities from
More information3- Remove stock silencer bracket from the bulkhead located above brake assembly (this bracket will not be used in installation).
SLP Single Pipe Set for 2004 ZR 900 P.N. 09-904CP Kit Contents: 2 1/4 Flat Washer 2 Large Head Rivets 2 1/4 Nylock Nuts 2 Rivet Washers 1 Stem Vibro Support 1 Medium Sping 1 pc 30 Reflective Heat Tape
More informationSingle Pipe Set with OEM Silencer for /800 RMK/XC, /800 SKS, /800 Switchback and Switchback
Single Pipe Set with OEM Silencer for 2002-05 700/800 RMK/XC, 2003 700/800 SKS, 2004 700/800 Switchback and 2005 800 Switchback P.N. 09-836 Important: Read instructions carefully before installation. Note:
More informationPOLARIS Twin 600/700 SINGLE PIPE SET P.N
1997-1998 POLARIS Twin 600/700 SINGLE PIPE SET P.N. 09-718 Important: Read instruction carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been placed
More informationSLP Single Pipe Set for Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N CP/09-914CP
Setting the Wld s Perfmance Standards SLP Single Pipe Set f 2004-05 Arctic Cat 900 Mountain Cat Carb and EFI with Transfer Outlet Tube P.N. 09-908CP/09-914CP Read instructions carefully and completely
More informationPOLARIS 700/800 PRO X SINGLE PIPE P.N
2003-04 POLARIS 700/800 PRO X SINGLE PIPE P.N. 09-839 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been placed there
More informationSLP Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N (CP)
Setting the World s Performance Standards Twin Pipes for 2004 Arctic Cat 900 Mountain Cat Twin P.N. 09-907(CP) Contents of Pipe Set 1 - Plastic Zip tie 3 - Large Head Rivets 4 - Short s 1 - Red Silicone
More informationSingle Pipe Set for Big Block: /700 XC/SKS/RMK and /700 RMK/SKS For use with Stock Silencer P.N
Single Pipe Set for Big Block: 2000 600/700 XC/SKS/RMK and 2001 600/700 RMK/SKS For use with Stock Silencer P.N. 09-732 Important: Read instruction carefully before installation. Note: Removal of pipe
More informationSinlge Pipe for /800 Pro-X/Pro-X2/Pro-XR P.N
Sinlge Pipe for 2003-04 700/800 Pro-X/Pro-X2/Pro-XR P.N. 09-9 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid section of the pipe. It has been
More informationSLP Twin Pipes for 2003 Arctic Cat 900 Twin
Setting the World s Performance Standards SLP Twin Pipes for 2003 Arctic Cat 900 Twin P.N. 09-902(CP) and 09-903(CP) IMPORTANT: Read instructions carefully before installation. 1. Remove stock exhaust,
More informationPOLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N
POLARIS 700 XC/SKS/RMK SLP TWIN PIPE SET P.N. 09-710 IMPORTANT: Read instruction carefully before installation. For engines with stock porting use either 09-700 glass pack pipe set or 09-710 canister pipe
More information1-Remove stock exhaust, Y-Pipe, and silencer (Retain OEM springs and exhaust gaskets for pipe installation).
Single Pipe Set for use with Performance Edition Kit for 2003-04 POLARIS 800 Pro X P.N. 09-848 Important: Read instructions carefully before installation. Note: Do not remove banding placed on the mid
More informationPart # SLP Single Pipe Set for G4 Ski Doo 850
Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Part # 09-867 SLP Single Pipe Set for 2017-18 G4 Ski Doo 850 Parts List: 7-7 Insulated
More informationSLP PART # ATTENTION DEALER
SLP PART #09-872 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following:
More informationSingle Pipe for Ski-Doo REV H.O. (For use with ported engines only) #09-870
the World s Performance Standards Single Pipe for 200-2006 Ski-Doo REV H.O. (For use with ported engines only) #09-870 Important: Read instructions carefully before installation. 1. Remove stock pipe and
More informationSLP Single Pipe for Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models)
SLP Single Pipe for 2006-09 Polaris 600 H.O. Fusion/RMK/Switchback/Shift (Carb Models) Part # 09-634 Kit Contents: 2-7 Insulated Heat Tape 1-1/8 Pipe Adjustment Washer 4-30 Reflective Heat Tape 1 - Wire
More informationSLP PART # ATTENTION DEALER
PART #09-8000 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following: The
More informationSLP PART # ATTENTION DEALER
SLP PART #09-883 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT. Before you begin, please read the following:
More informationPerformance Edition Kit (SLP Stage 4)
Performance Edition Kit ( Stage 4) for 2011-15 Polaris 800 RMK, Pro-RMK, Switchback Assault, RMK Assault & Indy 2011-14 800 Rush & Switchback Congratulations! You have just purchased one of the best modifications
More informationPart # SLP Silencer for G4 Ski Doo 850
Part # 09-867 SLP Silencer for 2017-18 G4 Ski Doo 850 Parts List: 7-7 Insulated Heat Tape (Part #090-29) 5-30 Reflective Heat Tape (Part #090-31) 1 - Inner Aluminum Heat Shield (Part #091-6057) 3-3/16
More informationKid Sprint Engine Rules Briggs World Formula
Kid Sprint Engine Rules Briggs World Formula 2017 Jr Sprint Engine Rules Briggs World Formula effective 2/1/2017. All parts must bebriggs & Stratton factory production parts unless otherwise noted in these
More information2018 Junior Sprint Rules
2018 KidSprint Engine Rules Briggs World Formula 2018B All parts must be Briggs & Stratton factory production parts unless otherwise noted in these rules. No machining, polishing or alteration of any parts
More informationHW Prowler Carburetor Installation Instructions
HW Prowler Carburetor Installation Instructions Page 1 of 6 Carb Kit Contains: HW modified Mikuni 36mm pumper style carb Custom choke cable Fuel Line Clamp Instructions (2) Leaner and (2) richer main jets
More informationMotorcycle Carburetor Theory 101
Motorcycle Carburetor Theory 101 Motorcycle carburetors look very complex, but with a little theory, you can tune your bike for maximum performance. All carburetors work under the basic principle of atmospheric
More informationSherco Carb Jetting Instructions
Sherco Carb Jetting Instructions This manual provides instructions on how to remove and reinstall the stock carburetor, it also shows you how to change the pilot jet and the main jet. It is intended to
More informationBA /02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07)
BA-2020-00/02/03/04/06/07/08/13/13B/15 BIG AIR KIT (BAK) - Yamaha Road Star (99-07) Page: 1 Revision: 6.2-02/23/2011 Install Time: 1.5 Hours We recommend a qualified Yamaha technician install this kit
More informationSLP PART# ATTENTION DEALER
*015-09866* Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 PART# 09-866 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION
More informationRacing Performance Catalog & Reference Guide Model/Type:
Version 4/08 Racing Performance Catalog & Reference Guide Model/Type: 124435 8105-01 Table of Contents SAFETY... 1 WORLD FORMULA General Specs...3 Special Tools...3 Torque Specs...3 Racing Specifics...3
More informationReproduction. Not for. Briggsracing.com. CORPORATION Briggs & Stratton Corporation MS /08
Briggsracing.com MS-5702-4/08 BRIGGS&STRATTON CORPORATION Post office box 702 Milwaukee, WI 53201 USA 414 259 5333 2008 Briggs & Stratton Corporation Version 4/08 Racing Performance Catalog & Reference
More informationSLP Single Pipe Set for 2007 Arctic Cat M1000
Single Pipe Set for 2007 Arctic Cat M1000 P.N. 09-876 Kit Contents: 1 - Silencer 1 - Spring Tab 1 - Large Head Rivet 1 - Short Spring 1 - Zip Tie 1-30 Reflective Heat Tape 1 - Y-Pipe 1 - Single Pipe Read
More information10. Oil injection pump must remain functional and in place lines may be removed and plugged. Premix gasoline may be used.
STOCK SNOWMOBILE GENERAL REQUIREMENTS 1. The snowmobile must use OEM clutch, suspension, gas tank, cowl, hood and engine for the snowmobiles year and model. Factory options are not 2. Snowmobile and driver
More informationMC Xpress AB Norra Altervägen ALTERSBRUK Sweden Tel:
Installation manual power upgrade kit Yamaha Sidewinder / Arctic Cat ZR 9000 Stage 1 / 225 hp and stage 2 / 250 hp MC Xpress AB Norra Altervägen 821 945 92 ALTERSBRUK Sweden Tel: +46 911 202005 www.mcx.se
More informationSLP Stage 2 Performance Kit for Polaris 800 Axys
Setting the World s Performance Standards 743 E. Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Stage 2 Performance Kit for 2015-17 Polaris 800 Axys The following tuning specification
More informationElectronic Jet Kit Instructions
Rev 1.0.3 8027ST-TFI Patent Numbers: 7,000,599, 7,124,742 Electronic Jet Kit Instructions Thank you for choosing the Dobeck Performance Electronic Jet Kit for you re Arctic Cat F/M1000 Snowmobile. Dobeck
More informationLocal Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # engine will be allowed in this class.
Local Option 206 Rules Manual Section 1 General Rules 1. Only stock Briggs & Stratton LO206 # 124332-8201engine will be allowed in this class. o All parts will be stock unaltered Briggs & Stratton Animal
More informationINSTRUCTIONS. High Boost Upgrade Polaris PRO-RMK Polaris SKS 850 (155) 2019 Polaris ASSAULT 850. Page Number: 1 INSTRUCTIONS MODEL:
INSTRUCTIONS MODEL: FITS: High Boost Upgrade 2019 Polaris PRO-RMK 850 2019 Polaris SKS 850 (155) 2019 Polaris ASSAULT 850 Page Number: 1 INSTRUCTIONS Table of Contents Contents INSTRUCTIONS...1 Contents
More information*** FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials SeaDoo 951XP Twin
*** FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials SeaDoo 951XP Twin Item Qty Part Number Part Description 1 1 COMASM0851 951XP MAG Chamber assembly 2 1 COMASM0850
More informationClasses INC. Northeast Snowmobile Racing INC SNOW DRAG RACING. Classes. Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open
INC Northeast Snowmobile Racing INC Classes SNOW DRAG RACING Classes Amateur: ( $15 Entry Fee + $5 Insurance Fee) Stock: 500, 600, 700, 800, Open Improved Trail: 500, 600, 700, 800, Open Pro: ( $25 Entry
More informationFactory Pipe Bill of Materials 650 Super Jet
Factory Pipe Bill of Materials 650 Super Jet Item# Qty. Part Description 1 1 Factory Pipe tunable cast aluminum headpipe 2 1 Factory Pipe aluminum chamber 3 1 Factory Pipe tuned exhaust manifold 4 2 100-120mm
More information*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Sea-Doo 785XP Spec I 1997
*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Sea-Doo 785XP Spec I 1997 Item# Qty Part # Part Description - 1 COMASM0200 785 Spec I hardware kit, 97 (includes items
More information600/700 to 1000cc (Dragon Cat) Big Bore Kit RACING PERFORMANCE HANDBOOK
600/700 to 1000cc (Dragon Cat) Big Bore Kit RACING PERFORMANCE HANDBOOK This Big Bore kit fits 2003-2006 F6, F7, Fire Cat and M-Series snowmobiles using the lay down engine design. CPC Racing Engines are
More information2007 HOP-UP INFORMATION. Foreword
2007 HOP-UP INFORMTION Foreword This manual contains the hop-up information for RM series of European specification and is intended to allow the standard model to achieve its maximum performance potential.
More informationCounter-clockwise, view to output shaft Mixture 1:50, 2-stroke-oil, fuel min. 95 octane (RON)
HIRTH 2703 Carburated - 55 hp The 2703 V is an air cooled, piston controlled 2-cylinder-inline-2-stroke engine with one or two carburetors and Nikasil coated cylinders. It has one of the highest power
More informationCarburetors 16. Download the current price list from: BPSite/pricelist.pdf. Carburetors and Gaskets
Carburetors 16 Carburetors and Gaskets Solex - Fitted Series II, IIA through 1967 We no longer stock Solex repair parts. When your Solex is no longer serviceable we suggest replacing it with a new Zenith
More informationSno Pro 120. Model Number S2012ACAAAUSG SHARE OUR PASSION.
2012Snowmobile Illustrated Parts Manual Sno Pro 120 Model Number S2012ACAAAUSG TM SHARE OUR PASSION. TABLE OF CONTENTS 2012 Sno Pro 120 (Model No. S2012ACAAAUSG) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY...
More informationCAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION
V-Twin MFG. VT No. 32-9500 V-TECH 1 IGNITION KIT, SINGLE FIRE FITS EV SHOVEL, XL THRU 1997 VT No. 32-9503 V-TECH 1 IGNITION KIT, SINGLE FIRE FITS EV, SHOVEL, XL, WITH COIL AND WIRES This is a custom application
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List XL Gas Concrete Saw Effective July, 0 0 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject to change without
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List GC & F Gas Concrete Saw Effective January, 0 0 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject to change
More informationWorld Formula TECH MANUAL
World Formula TECH MANUAL Section 1 General Rules 1. Only stock Briggs & Stratton World Formula Model # 124435-8101 will be used in this class except as provided in this Tech manual. All parts will be
More information"F" SERIES (Cont.) AIR FILTER ASSEMBLY NOTE NOTE. To remove grasp the cover, loosen snap and. If engine is flooded, fuel can drain back into
CARB.-AIR-FILTER ASSEMBLY GASKET RETAINER PASSAGE AIR FILTER ASSEMBLY AIR FILTER If engine is flooded, fuel can drain back into filter. As filter becomes saturated, incoming air picks up more fuel, causing
More informationCounter-clockwise, view to output shaft Mixture 1:50, 2-stroke-oil, fuel min. 95 octane (RON)
HIRTH 2703 Carburated - 55 hp The 2703 V is an air cooled, piston controlled 2-cylinder-inline-2-stroke engine with one or two carburetors and Nikasil coated cylinders. It has one of the highest power
More information... TX-L MODEL NUMBER CONTENTS 2-3 BODY. 4-6 HOOD ASSEMBLY IGNITION ASSEMBLY. 8-9 SEAT ASSEMBLY STEERING ASSEMBLY.
.. ~ : l~ :;~, ~ 0 J-I-'olaris I I '. ... TX-L MODEL NUMBER 080639 CONTENTS BODY. HOOD ASSEMBLY IGNITION ASSEMBLY. SEAT ASSEMBLY... STEERING ASSEMBLY. CHAINCASE ASSEMBLY. DRIVE CLUTCH. DRIVEN CLUTCH. DRIVE
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List GC & F Gas Concrete Saw Effective July, 0 0 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject to change without
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List GC & F Gas Concrete Saw Effective January, 0 0 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject to change
More informationAC 120 MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP
2008 AC 120 Illustrated Parts Manual MODEL NUMBER S2008ACAAAUSG MODEL NUMBER S2008ACAAAUSP TABLE OF CONTENTS (Model No. S2008ACAAAUSG) (Model No. S2008ACAAAUSP) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY...
More informationNEW V FORCE REED CAGES FOR POLARIS ENGINES
NEW V FORCE REED CAGES FOR POLARIS ENGINES Steve Tassinari of Moto Tassinari sent DTR new Vforce3 reed cages that fit the Polaris CFI twins, and asked us to do a back-to-back comparison of stock vs. new
More informationItem No. Description Chevrolet X 4 crew cab long box 1 ton pickup Chevrolet 2500HD Crew Cab 4X4 Pickup Western Pro
Item No. Description 101 2004 Chevrolet 3500 4 X 4 crew cab long box 1 ton pickup 102 2002 Chevrolet 2500HD Crew Cab 4X4 Pickup 103 2006 Western Pro Plow 8 ft snow plow w/ Ultra Mount (like new) 104 1999
More informationSkidoo XM Etec Installation Instructions
Thank you for purchasing your Silber Turbo kit. This product was designed to give you endless amounts of power and satisfaction. During the installation feel free to call us with any question or concerns
More informationBig Block Installation
Factory Five Racing, Inc. Big Block Installation 427 Shown here with fuel injection. 1 These instructions are designed to supplement the assembly manual where the assembly process is different from the
More information*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill Of Materials Yamaha GP1200R
*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill Of Materials Yamaha GP1200R Item Qty Part Number Part Description 1 3 COMASM0690 GP1200R Flange assembly 2 1 COMASM0840 GP1200R
More information120 XC SP Model #S01WB1AS Rev. 01. E 2000 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /00
0 XC SP Model #S0WBAS Rev. 0 E 000 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN 0/00 C CARBURETOR... B CLUTCH... A CRANKCASE... B D DECALS... A DRIVE TRAIN... A E ELECTRIC DEVICE... B ELECTRICAL
More informationSilverPro Series. Lawnmower. Parts Catalog. Form Number Model No and up.
Form Number 3350-622 SilverPro Series Lawnmower Model No. 10323-240000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number, the quantity, and the
More informationRemove Air Cleaner Cover and. Filter
Remove Air Cleaner Cover and Inspect paper filter for tears Foam pre-cleaner is washable if equipped Replace if necessary Filter Remove Trim Panel Pull throttle lever knob off Remove 3, 8mm screws Remove
More informationBackwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit
Backwater Performance Systems Large Vanguard Mikuni Twin Carburetor Kit 1. Throttle Cable Twin (CKC-41) 2. Carburetor VM30mm (CKC-40) 3. Loctite 242.5mL (A-210) 4. Air Cleaner Filter 6000 (EC-86) 5. Rev
More informationINSTALLATION INSTRUCTIONS for HI-4 DUAL FIRE MOTORCYCLE IGNITION. Part Number INTRODUCTION REMOVAL OF POINTS IGNITION TO 1977 MODELS
INSTALLATION INSTRUCTIONS for HI- DUAL FIRE MOTORCYCLE IGNITION Part Number -00 CAUTION: READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION INTRODUCTION The HI- ignition system is intended for use
More informationPOLARIS MARINE 1200 Model #W000099D Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /00
POLARIS MARINE 00 Model #W000099D 000 Polaris Sales Inc. PARTS MANUAL PN 9968 and MICROFICHE PN 9969 /00 TABLE OF CONTENTS POLARIS MARINE 00 W000099D Parts Manual A AIR VENT...........................
More informationChecking Solenoid Plunger Travel
1985 Chevy Truck EL Camino V8-305 5.0L Page 1 Carburetor: Adjustments Carburetor Calibration E2M & E4M Series Mixture Control Solenoid Plunger Travel Checking Solenoid Plunger Travel OTE: Mixture control
More informationGeneral Rules for ALL classes: (Please read these rules and understand them before you sign up.)
2019 Long Lake Vintage Snowmobile Racing Association General Rules for ALL classes: (Please read these rules and understand them before you sign up.) NO CHANGES, Modification allowed UNLESS specified in
More informationIllustrated Parts Manual
2010 Illustrated Parts Manual 120 Sno Pro Model Number S2010ACAAAUSG SHARE OUR PASSION ṬM TABLE OF CONTENTS 2010 120 Sno Pro (Model No. S2010ACAAAUSG) SKI AND SPINDLE ASSEMBLY... 1 A-ARM ASSEMBLY... 2
More informationBriggs & Stratton Animal TECH MANUAL Version 1.6 Section 1 General Rules cannot Section 2 Required Modifications Section 3 Allowable Modifications
Briggs & Stratton Animal TECH MANUAL Version 1.6 updated 2/ 7 / 2011 Section 1 General Rules 1. Only stock Briggs & Stratton Animal # 124332-8201and 124332-8203 - 01engine will be allowed in this class.
More informationClutching for 2019 Polaris 850 RMK
Clutching for 2019 Polaris 850 RMK Important: The following clutching information has been thoroughly tested and is highly recommended for proper performance and reliability. Primary weights, drive spring
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 633GC / 633F4 Gas Concrete Saws Effective January 1, 20167 TABLE OF CONTENTS 633GC / 633F4 Gas Saws ITEM DESCRIPTION KEY PAGE 633GC / 633F4 Gas Saw Service Items
More informationrev 2_ EA5000P53G (Makita Teal) EA5000PR (Makita Red) PS-5105 (Dolmar Red) PS-5105H (Dolmar Red)
(Makita Teal) (Makita Red) (Dolmar Red) H (Dolmar Red) 1 Tank, Handle 5 25 17 3 12 1 15 6 114 113 16 13 9 10 14 8 11 4 2 18 21 23 20 22 24 2 1 Tank, Handle H 1 1 181-114-720 TANK CPL. BLUE 1 1 1 181-114-280
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 695XL Gas Concrete Saw Effective January 1, 2018 I TABLE OF CONTENTS 695XL Gas Saw ITEM DESCRIPTION KEY PAGE 695XL Gas Saw Service Items n/a 2 Starter Assembly
More informationIllustrated Parts Manual
ARCTIC CAT SHARE OUR PASSION. TM Illustrated Parts Manual AC 120 Model Number S2007ACAAAUSG Model Number S2007ACAAAUSO 2007 TABLE OF CONTENTS 2007 AC 120 (Model No. S2007ACAAAUSG) (Model No. S2007ACAAAUSO)
More informationTSS Fit Kit Installation Instructions Timbersled Snow Bike System
TSS Fit Kit Installation Instructions Timbersled Snow Bike System Information needed before you start: Read the entire installation instructions before starting. The instruction sheet is universal for
More informationTRIMMER/BRUSH CUTTER PARTS CATALOG MODELS SRM-3800 TYPE 1
TRIMMER/BRUSH CUTTER PARTS CATALOG MODELS SRM-3800 TYPE 1 SERIAL NUMBER 0001 & UP MODELS SRM-3800 TYPE 1E SERIAL NUMBER 0001 & UP ECHO, INCORPORATED 400 OAKWOOD ROAD LAKE ZURICH, IL 004 2224 0/ ENGINE,
More informationBASIC INSTRUCTIONS SHIFTER KZ1 / KZ2 e X30 SHIFTER-TaG
BASIC INSTRUCTIONS SHIFTER KZ1 / KZ2 e X30 SHIFTER-TaG FEEDING: by fuel mixture 98NO (min. 95NO) and 4% oil (CIK homologated). ATTENTION: the engine is supplied without oil in the gearbox. GEARBOX OIL
More informationCHAINSAW PARTS CATALOG CS-346: ECHO, INCORPORATED 400 Oakwood Road Lake Zurich, Illinois MODEL: SERIAL NUMBERS. 33.
AVAILABLE ATTACHMENTS & ACCESSORIES 0 CHAIN - " 0 CHAIN - " 0 CHAIN - " 00 GUIDE BAR - " 00 GUIDE BAR - " 00 GUIDE BAR - " 0 GUIDE BAR - " INTENZ 0 GUIDE BAR - " INTENZ 0 GUIDE BAR - " INTENZ 000 REMOVABLE
More informationDAYTONA 700 (97DTA-1997) Page 1 of 60 BILGE PUMP ASSEMBLY
1997 DAYTONA 700 (97DTA-1997) Page 1 of 60 BILGE PUMP ASSEMBLY 1997 DAYTONA 700 (97DTA-1997) Page 2 of 60 BILGE PUMP ASSEMBLY Ref # Part Number Qty S/P/F Description 1 0673-377 1 Fitting, Outlet - Bilge
More informationCHAIN SAW PARTS CATALOG MODEL CS-6700 TYPE 1E SERIAL NUMBER & UP
CHAIN SAW PARTS CATALOG MODEL CS-00 TYPE 1E SERIAL NUMBER 0001 & UP ECHO, INCORPORATED 400 OAKWOOD ROAD LAKE ZURICH, IL 004 999203008 0/03 CS-00 TYPE 1E ENGINE, CRANKCASE, CYLINDER, PISTON 20 1 2 38 39
More informationContents. Contents Page 3 FOREWORD...2 CONTENTS...3
Contents Page 3 Contents FOREWORD...2 CONTENTS...3 INTRODUCTION...4 OBJECTIVES OF WORK...4 TOOLS AND OTHER USEFUL STUFF...4 MODS...7 GENERAL...7 DYNO TESTING...8 MAINTAIN OPTIMUM STOCK PERFORMANCE...11
More informationHIRTH 2703 Carburated - 55 hp
HIRTH 2703 Carburated - 55 hp The 2703 V is an air cooled, piston controlled 2-cylinder-inline-2-stroke engine with one or two carburetors and Nikasil coated cylinders. It has one of the highest power
More information***FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki Ultra 150 Triple Pipe
***FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki Ultra 150 Triple Pipe Item Qty Part Number Part Description 1 1 COMASM0947 Ultra 150 PTO Chamber assembly
More informationTRAIL BLAZER 250 Model #A03BA25CA. E 2002 Polaris Sales Inc. PARTS MANUAL PN and MICROFICHE PN /02
TRAIL BLAZER 0 Model #A0BACA E 00 Polaris Sales Inc. PARTS MANUAL PN 0 and MICROFICHE PN 0 /0 This page left blank intentionally. TABLE OF CONTENTS Trail Blazer A0BACA Parts Manual A- ARM... B AIR BOX...
More informationCARBURETOR. Preliminary Check. Removal of DuraForce Carburetor
Fuel Leaks From Carburetor (Leaking starts after running, stops after shutdown) Note: This condition which does NOT drain the fuel tank is called spit-back. Possible Causes Engine RPM out of proper range
More information* * * FOR COMPETITION USE ONLY per US EPA regulations* * * Factory Pipe Bill of Materials 1996-Up 701 SuperJet Limited
* * * FOR COMPETITION USE ONLY per US EPA regulations* * * Factory Pipe Bill of Materials 1996-Up 701 SuperJet Limited Item# Qty. Part Number Part Description 1 1 COMCST0040 B Headpipe - 701 Yamaha all/xir
More informationAccident Prevention Program
Accident Prevention Program Part I ENGINE OPERATION FOR PILOTS by Teledyne Continental Motors SAFE ENGINE OPERATION INCLUDES: Proper Pre-Flight Use the correct amount and grade of aviation gasoline. Never
More informationSetting the World s Performance Standards
Setting the World s Performance Standards 743 East Iona Road, Idaho Falls, ID 83401, (208) 529-0244 Fax (208) 529-9000 Lightweight Silencer for Polaris: 2016-17 800 Axys Models & 2017 600 Pro-RMK P/N 09-322
More informationPARTS MANUAL PN and MICROFICHE PN /03. OCTANE Model #W045402DA. E 2003 Polaris Sales Inc.
PARTS MANUAL PN 0 and MICROFICHE PN 00 /0 OCTANE Model #W00DA E 00 Polaris Sales Inc. This page left blank intentionally. TABLE OF CONTENTS OCTANE W00DA Parts Manual BATTERY BOX... BILGE PUMP... CARBURETOR...
More informationARCTIC CAT 04 F7 EFI FIRECAT UPDATE:
ARCTIC CAT 04 F7 EFI FIRECAT UPDATE: Bill DiFranco (AKA looneytune on the internet who previously provided his 03 F7 for evaluation for DynoTechResearch) swapped his sled for an 04. Then he came to the
More informationA Simple View of Fuel Injection
A Simple View of Fuel Injection Your engine is an air pump, the more air you pump through it, the more power you make. Figure 1 Any internal combustion engine will flow air at a rate determined by many
More informationPLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT IS SUPPLIED IN THIS PACKET FOR THIS PRODUCT.
the World s Performance Standards 743 E. Iona Road, Idaho Falls, ID 831, (208) 529-0244 Fax (208) 529-9000 ATTENTION DEALER PLEASE PROVIDE YOUR CUSTOMER WITH THE INSTALLATION AND INSTRUCTION DATA THAT
More informationIllustrated Parts Manual. ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR
Illustrated Parts Manual ZR 120 Model Number S2005ZRAAAUSG Model Number S2005ZRAAAUSR 2 00 5 TABLE OF CONTENTS 2005 ZR 120 (Model No. S2005ZRAAAUSG) (Model No. S2005ZRAAAUSR) SKI AND SPINDLE ASSEMBLY.................................................
More informationIllustrated Parts List
01/08/2010 FILE IN SECT. 2 OF SERVICE MANUAL PRO DRIVE 613777-0113 -E1 Illustrated Parts List Model Series AIR COOLED 613777 TYPE NUMBERS 0113. TABLE OF CONTENTS Air Cleaner... Alternator... Blower Housing/Shrouds...
More information