7100SZ Series SafeZone Installation and Instruction Manual
|
|
- Eileen Fowler
- 6 years ago
- Views:
Transcription
1 7100SZ Series SafeZone Installation and Instruction Manual Patent Pending (10-10) Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 5 for template) 3 1 Push Side Applications with Double Lever Arms (710SZ, 7130SZ) (see page 3 for template) Item No. Description 1 Track Cover 3 Arm (Pull Side) Double Lever Arm (Push Side) Requirements: Units are handed.hand of unit and hand of door must be the same. Door must be hung on ball bearing butt hinges or ¾ (19) offset pivots. Door thickness must be 1¾ () minimum ¼ (6) maximum. Door must swing freely through the entire opening and closing cycle before beginning the installation procedure. Frame face must be a minimum of (51). Ceiling clearance must be a minimum of (10). Power input to unit must be of the same voltage as that stated on the unit. Unit to be mounted on interior of building in dry environment, maximum humidity of 95%. See NFPA70 for wiring requirements and NFPA7 for alarm system requirements.
2 Component Layout Closer/Holder Unit Assembly Backplate Mtg Screw (5) Backplate Sensor Hook-up Board Access Tube Standard Fasteners 1/ - 0 machine screw Sleeve nuts and bolts Optional Through-bolts and grommet-nuts Preparation for Fasteners Door or Frame Drill-Sizes Drill: #7 (0.01 dia.) Metal Tap: 1/ - 0 Hollow Metal Aluminum or Wood All 9/3 (7 mm) through; 3/8 (9.5 mm) door face opposite to closer 3/8 (9.5 mm) through 9/3 (7 mm); 3/8 (9.5 mm) dia. x 3/8 (9.5 mm) deep on door opposite to closer Cover Cover Mtg Screw (3) Included with 7110SZ and 7150SZ Included with 710SZ and 7130SZ 7110 Main Arm (710-1A) 7150 Main Arm, Handed (750-1L, 750-1R) Slide Track (700-1T) 7130 Arm Assembly (7701-1B) Screw & Washer Slide Assembly (7700SLD) Arm Screw (7701-MAS) 710 Arm Assembly (7701-1A) Track Mtg Screw (3) NOTE: Optional remote for Advanced Settings (sensitivity, door control mode) if required. (7100REM) Certifications UL8 UL10B Page (10-10)
3 710SZ, 7130SZ Double Lever Arm (Push Side) Ceiling Line 3-1/ Min (89) Min (51) Use of an auxiliary door stop, by others, is suggested, but is required for doors opening beyond 110. Hinge Edge RH - Right Hand Door LHR - Left Hand Reverse 1 Drill #7; Tap 1/ /16 (10) A -1/8 (105) 11-3/8 (89) (87) For Concealed 8-11/16 WiringOnly (1) 7/8 () 5/16 (8) 11/16 (17) DIA THRU Left Hand Door - LH Right Hand Reverse - RHR 3 C Hinge or Pivot 7-1/ (191) 1-3/ () 1-5/8 (1) Left hand door shown, right hand opposite. All dimensions shown in inches (mm). DOOR OPENING ANGLE To to 180 For Concealed Wired Only (If surface wired, go to Step 3.) Dimension A Inches (mm) 5-7/8 3-1/ Arm Mark L Y S R Z Pinion Flat Main Arm Arm Screw (7/16 Drive) Page (10-10)
4 7 8 Closing Force 90 11/16 Drive + 11/16" Drive Product shipped with closing force set at the middle of the power range. 9 Latch Sweep 1/8 wrench provided Positioning (75-95 ) Strength! Caution: Do not completely close backcheck valve. 10 MAKE ELECTRICAL CONNECTIONS: Power input to unit must be of the same voltage as that listed on the label. All wiring connections use standard wiring practice conforming to local wiring codes. Maximum wire size is 18AWG. Make input power connections to the hook-up board terminal strip using illustrations.! Caution: Determine proper control board; V or 10V. V AC/DC INPUT CIRCUIT BOARD 10V AC INPUT CIRCUIT BOARD Fuse PTO15V (15V / 1/A) V AC/DC Power Input Solenoid Safe Zone Sensor Fuse PTO15V (15V / 1/A) 10V AC Power Input Solenoid Safe Zone Sensor 11 1 Adjust settings Page (10-10)
5 7110SZ, 7150SZ Track Mount (Pull Side) Ceiling Line Min (10) Use of an auxiliary door stop, by others, is suggested, but is required for doors opening beyond 110. (51) Min 1 Drill #7; Tap 1/-0 (10) 3-1/ (83) RH - Right Hand Door LHR - Left Hand Reverse -1/8 (105) 11-3/8 (89) 19-3/16 (87) For Concealed 8-11/16 Wiring Only (1) 7/8 () 1-1/16 (7) 1-3/8 (35) Left Hand Door - LH Right Hand Reverse - RHR DIA THRU (10) C Hinge or Pivot Track Mount Unit 11 (79) (559) 1-3/16 (30) 3 For Concealed Wired Only (If surface wired, go to Step 3.) Right hand door shown, left hand opposite. All dimensions shown in inches (mm). 5 6 Arm Indexing Fully close Latch and Sweep Valves with 1/8" wrench provided. RIGHT HAND RE-INSTALL HERE LEFT HAND Use main arm to rotate pinion until flat is visible. PINION FLAT Page (10-10)
6 7 8 9 Arm Stud Slide Assembly Arm Washer Arm Screw Main Arm Open Latch & Sweep Valves with 1/8 wrench provided Closing Force 11 1/8 wrench provided! Caution: Do not completely close backcheck valve Latch Sweep Strength /16 Drive Product shipped with closing force set at the middle of the power range. MAKE ELECTRICAL CONNECTIONS: V AC/DC INPUT CIRCUIT BOARD Positioning (75-95 ) Power input to unit must be of the same voltage as that listed on the label. All wiring connections use standard wiring practice conforming to local wiring codes. Maximum wire size is 18AWG. Make input power connections to the hook-up board terminal strip using illustrations.! Caution: Determine proper control board; V or 10V. 10V AC INPUT CIRCUIT BOARD Fuse PTO15V (15V / 1/A) V AC/DC Power Input Solenoid Safe Zone Sensor 13 1 Fuse PTO15V (15V / 1/A) 10V AC Power Input Solenoid Safe Zone Sensor Adjust settings Page (10-10)
7 SafeZone Set-Up Sensor Technical Specifications DESCRIPTION SPECIFICATION Frequency:.15 GHz Supply voltage: 1 to V AC: 10%: 1 to V DC: -10% / +30%: Mounting height: Normal: 7 ; Maximum: 10-0 Tilt angle: 0 to 90 vertical -15 to +15 lateral Detection area: Wide Narrow 13ft (W) x 6.5ft (D) 6.5ft (W) x 8.ft (D) (supplied as optional) Minimum detection speed: in/sec. (measured in axis) Power consumption: Standard output relay: Max contact voltage Max contact current Max switching power < W 60 VDC / 15 VAC 1 A (resistive) 30W (DC) / 60VA (AC) 0.5 sec. to 9 sec. (adjustable) Hold time: Temperature range: - F to 131 F Dimensions:.75in (W) x 3.15in (H) x.0in (D) Weight: 0.5lbs Material: ABS Safety Precautions Shut off all power going to the header before attempting any wiring procedures. Maintain a clean & safe environment when working in public areas. Constantly be aware of pedestrian traffic around the door area. Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door. Always check placement of all wiring and components before powering up to insure that moving door parts will not catch any wires and cause damage to equipment. Ensure compliance with all applicable safety standards upon completion of installation. ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS Circuit board components are vulnerable to damage by electrostatic discharge (ESD). ESD can cause immediate or subtle damage to sensitive electronic parts. An electrostatic charge can build up on the human body and then discharge when you touch a board. A discharge can be produced when walking across a carpet and touching a board, for example. Before handling any board, make sure you dissipate your body s charge. CAUTION: In the event a unit needs to be opened, observe the following precautions. Ground yourself by touching a conductive surface of the door or other element connected to common earth ground to discharge the static electricity present in your body. Avoid walking around while replacing items inside the case, especially if you are on carpet or during conditions of low temperature and low humidity. Handle the board by the edges only to avoid touching electronic components. Store a loose board in an anti-static bag. Page (10-10)
8 Mechanical Adjustments THE POSITION OF THE SENSING FIELD IS DETERMINED BY THE VERTICAL AND LATERAL ANGLE OF THE ANTENNA A B C -30º +30 0º 30º 5º Sensing field as close to the door as possible: -antenna set at the position of 0 Sensing field close to the door: -antenna set at the position of 30 Sensing field far from the door: -antenna set at the position of 5 Set Up Hold open time refers to the time the door will remain open AFTER movement is no longer detected. Hold open time can be adjusted manually by means of the push buttons + (more) and - (less). + Press to increase hold open setting (see table below). - Press to decrease hold open setting. Pressing the two push buttons, located on the circuit board, simultaneously for three seconds, will restore all default settings. Setting Time (Seconds) (Default) Recommended Settings: Setting 1-3 Setting -6 Setting 7-9 Troubleshooting SYMPTOMS PROBABLE CAUSE CORRECTIVE ACTION Red LED does not light up. The sensor power is off. Check the wiring and power supply. Cable is not connected. Connect cable. ASSA ABLOY Norton is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Safe Zone is a trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright 010 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. Page Highway7East Monroe,NC811 Tel: (877) Fax: (800) (10-10)
Power drill Center punch Wire stripper
Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 7 for template) 7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 3 1 Push Side Applications with Double Lever
More informationASSA ABLOY. 7100SZ Series SafeZone External Sensor. Installation and Instruction Manual ASSA ABLOY. Patent Pending
700SZ Series SafeZone External Sensor Installation and Instruction Manual Patent Pending.76 (0). (79.8) Tools required:.0 (0.8) Allen wrench set (inch) Flat blade screwdriver (potentiometer & terminal
More information7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor
7100SZ Series SafeZone Multi-Point Closer/Holder with Motion Sensor INTRODUCTION Designed with safety in mind, SafeZone takes door closers to a higher level. SafeZone uses a multi-point, electromechanical
More information7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor
7100SZ Series SafeZone Multi-Point Closer/Holder with Motion Sensor Page Revised Electronically 8/11 7100SZ Series SafeZone INTRODUCTION Designed with safety in mind, SafeZone takes door closers to a higher
More informationASSA ABLOY Series Multi-Point Hold Open Installation and Instruction Manual
Pull Side Applications with Slide Track (7210, 7250) (see page 7 for template) 7200 Series Multi-Point Hold Open Installation and Instruction Manual 3 1 Push Side Applications with Double Lever Arms (7220,
More informationMulti-point closer/holder with motion sensor 7100SZ DOOR CLOSER CATALOG
Multi-point closer/holder with motion sensor 7100SZ S E R I E S DOOR CLOSER CATALOG INTRODUCTION The 7100 Series SafeZone door closer safeguards occupants throughout a variety of facilities with the detection
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions
More information7100SZ SERIES. Multi-Point Closer/Holder with Motion Sensor
safezone Multi-Point Closer/Holder with Motion Sensor introduction Designed with safety in mind, SafeZone takes door closers to a higher level. SafeZone uses a multi-point, electromechanical closer and
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO
More informationASSA ABLOY MPI (Infinite Hold Open Range) Support Unit Models. Multi-Point Electromechanical Overhead Concealed Closer Holder Releasing Device
Overhead Concealed Closer Holder Releasing Device with Rigid Slide Arm For wood or metal doors 1-3/4 to 2-1/4" (45-57mm) thick Hung in a hollow metal frame Standard butt hinges Typical Installation One
More information5600 Series Power Operator Installation and Instruction Manual
5600 Series Power Operator Installation and Instruction Manual 80-956-000-00 (08-) 5 ASSA ABLOY 6 Item No. Description Motor (5600M) Cover (5600COV) Control Inverter (5600IN) Power Supply VDC (5600PS)
More informationConcealed overhead closer for high-end applications DOOR CLOSERS CATALOG
Concealed overhead closer for high-end applications 7900 S E R I E S DOOR CLOSERS CATALOG INTRODUCTION The 7900 Series Overhead Concealed Closers offer extremely durable operation with the vandal resistance
More information9000 Series Trinity The world's most intelligent door closer
9000 Series Trinity The world's most intelligent door closer INTRODUCTION Designed for doors that are subject to changing conditions, the Norton 9000 Series Trinity offers customers an intelligent door
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
More informationFIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke
More informationFull-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG
Full-featured operator with slim profile for moderate to high traffic applications 6300 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The Norton 6300 Series Low Energy Operator offers a broad set
More information5700 Series Power Operator Stop (Push) Side Mount Installation and Instruction
5700 Series Power Operator Stop (Push) Side Mount ASSAManual ABLOY Installation and Instruction 80-957-0005-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 5 6 0 8 7 9 -/8 () Item No. Description Back plate Door
More informationFIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE
FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke barrier doors.
More information51 Series Door Closers. An ASSA ABLOY Group brand
51 Series Door Closers An ASSA ABLOY Group brand Introduction CONTENTS Features & Benefits...3 Overview...4 Fasteners...4 Features...5 Finishes...6 How to Order...7 Applications...8 Technical Details...9-11
More informationSeries 9540 J9540. Installation Instructions Multi-Sized 1 to 6 Non-Hold Open. Regular Arm Applications. Parallel Arm Applications
Series 940 J940 ASSA JL940 ABLOY Installation Instructions Multi-Sized to 6 Non-Hold Open Regular Arm Applications Left Hand Regular Arm Application Contents Page Template Template with 984-8 Drop Plate
More informationQUADSCAN User s Guide Door Mounted Presence sensor
QUADSCAN User s Guide Door Mounted Presence sensor DESCRIPTION 6 7 8 9 0. housing. clip. main connector. DIP-switch. range adjustment screw 6. receiver 7. end cap 8. clip with angle adjustment screw 9.
More information9540 SERIES. Cast Iron Door Closer
Cast Iron Door Closer Introduction The Norton 9540 s provide an ideal retrofit solution for retail, office, government and other commercial facilities. Certified to ANSI/BHMA Grade 1 requirements for long
More information51 Series Door Closers. An ASSA ABLOY Group brand
51 Series Door Closers An ASSA ABLOY Group brand Introduction contents Features & Benefits...3 Overview...4 Fasteners...4 Features...5 Finishes...6 How to Order...7 Applications...8 Technical Details...9-11
More information5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY
5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY 80-957-000-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 6 5 0 8 7 9 Item No. Description Back plate Door Closer
More informationCloser with traditional styling for low to moderate traffic openings 78-B/F DOOR CLOSER CATALOG
Closer with traditional styling for low to moderate traffic openings 78-B/F S E R I E S DOOR CLOSER CATALOG Introduction The 78-B/F Series is a surface closer with traditional styling that offers multiple
More informationTS93 EMF T/PT/TDE. Surface applied door closer
TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress
More informationASSA ABLOY Universal Door Closers
Installation Instructions For Non-Hold Open or A Hold Open Arm Options DC6200 Series DC6400 Series Multi-Sized thru 6 Half-Size thru 6 Regular Arm Parallel Arm Universal Door Closers Jamb Mount See pages
More informationLCN 4310ME SERIES FEATURES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled
HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for FEATURES fire and smoke barrier doors. Door
More informationDoor Closer Arms DC F95 (Non-Hold Open) Regular Arm Used with regular arm mounting (pull side) and top jamb mounting (push side)
Door Closer Arms Used with regular arm mounting (pull side) and top jamb mounting (push side) Non-Hold Open arm standard on the DC3200 (Hold-Open) 597F52 Heavy-Duty Mounted on pull side Optional on DC3200
More informationNON-SIZED SIZED HANDED
HINGE (PULL) SIDE MOUNTING 4310ME SERIES The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.
More informationLCN 4310ME SERIES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled. closer/holder designed to provide
HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide FEATURES infinitely adjustable hold-open for fire and smoke barrier doors. Door
More informationNON-SIZED SIZED HANDED
4410ME SERIES TOP JAMB (PUSH SIDE) MOUNTING The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.
More informationKEANE MONROE a member of the record group
SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully
More information78-B/F Series. Traditional Door Closers
78-B/F Series Traditional Door Closers introduction The Norton Series 78-B/F Traditional Surface Closers represent a combination of traditional styling and modern closer features. All closer sizes are
More informationHinge (Pull) Side Door Application DC6230 Series Multi-Sized 1 thru 6 DC6430 Series Half-Size 1 thru 6. Door Mounted DC6230 & DC6430
Installation Instructions Universal Door Closers Slide Track Application (0 Maximum Door Swing) (standard)- N.H.O. Bumper Stop A - H.O. Bumper Stop Track - Pull Side See pages 2 & Hinge (Pull) Side Door
More informationInstallation Instructions (07-08) CAUTION
Hinge Edge of Hinge Edge of 7500 eries Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should
More informationTS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall)
TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall) TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer
More informationCopyright , 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express
over he ad conce aled closer s o v e r h e a d c o n c e a l e d c l o s e r s i n t r o d u c t i o n i n t r o d u c t i o n Rixson Overhead Concealed closers offer an aesthetically appealing way to
More informationCONCEALED CLOSER SERIES
CLOSER SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of
More informationInstallation Instructions Series 78-B/FHA Hold Open
Installation Instructions Series 78-B/FHA Hold Open Traditional Style Door Closers Read these instructions before proceeding with the installation. Make sure that the door opens the full angle desired
More informationDC5000 Series. Cam Action Door Closer
Series Cam Action Door Closer Introduction Table of Contents Introduction...2 Features... 3 Mountings... 4 Accessories... 5 How to Order... 6 Quick Codes... 6 Helpful Terms... 7 Specifications... 8 Applications
More information626F Exit Device Trim Installation Instructions
626F Exit Device Trim Installation Instructions For use with all Yale 7000, 2100, 1800 and 1500 Series Exit Devices (Wood and Metal Doors) Attention Installer Any retrofit or other field modification to
More informationDOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM
SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of the closer.
More information*24771* 4040SE DE Sentronic. 1 Voltage. 7 Regulation. 2 Track. 8 Door Closer Cover. 3 Spring Power. 4 Arm Installation. 5 Arm Screw.
*2477* 2477 SE Egress 4040SE DE Sentronic Installation Instructions This closer features mounting options for both standard and step-down double egress frames. Before beginning, determine which type of
More informationHigh Security Closers Series
High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can
More informationNON-SIZED SIZED HANDED
4040SE SERIES n Standard 4040SE Series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks are optional,
More informationLCN 4040SE SERIES FEATURES HINGE (PULL) SIDE MOUNTING
HINGE (PULL) SIDE MOUNTING Standard 4040SE series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks
More informationCONCEALED CLOSER SERIES
CONCEALED CLOSER SERIES APPLICATIONS n For aluminum, hollow metal, or wood doors and frames. n Can be used with hinge or pivot mounted door. n Closers for 4 or minimum 1-3/4 head frame or 4 top rail. n
More information268, 269 & 278. Concealed Door Closers
268, 269 & 278 Concealed Door Closers Copyright 2004-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents General Information....3 268 Features and Benefits...4
More information4310ME Series. Features E25. Special Templates. Certifications. Cover Fasteners Mounting Arms
4310ME Features The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until
More informationASSA ABLOY Universal Door Closers with Heavy Duty Spring Stop Parallel Arms
DC610 Series Multi-Sized 1 thru 6 DC610 Series Half-Size 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH
More informationSuperior door control for rigorous, high-use applications 6000 LOW ENERGY OPERATOR CATALOG
Superior door control for rigorous, high-use applications 6000 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The 6000 Series low energy operator is a heavy-duty unit designed for rigorous, high-use
More information9540 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9540 SERIES The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated,
More informationMetal, Standard Wood and machine screw pack Top jamb (Push Side) Body Construction. Finishes/Colors/ Powder Coat. Wiring NON-SIZED SIZED
Features The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until current
More information9530 Series Senior Swing. Features. Special Templates. Fasteners Mounting. Certifications
Features The 9530 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows
More information7570 SERIES Security Door Closer
7570 SERIES Security Door Closer INTRODUCTION Norton High Security Closers are designed for use in prisons, government buildings, schools, financial institutions, or any installation where vandalism, abuse,
More information4310ME Series. Features E25. Special Templates. Grade 1 - ANSI A156.15, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act, NFPA 101
Features The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until current
More information9550 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting
Senior Features The 9550 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet
More informationMulti-sized cast iron closer for high use applications DOOR CLOSER CATALOG
Multi-sized cast iron closer for high use applications 9500 S E R I E S DOOR CLOSER CATALOG INTRODUCTION Ideal for high use openings, the Norton 9500 Series Cast Iron door closer offers the durability,
More informationWARNING: Make sure that (120V, 60Hz) input power is turned off at facility s main circuit breaker before proceeding with installation.
6000 Series Operator Installation and Instruction Manual ASSA ABLOY 6020 1 7 (up to 110 opening) 3 4 5 6 6030 2 (110 to 180 opening) 5 8 Item No. Description 1 2 Motor (6000M) Cover (6000COV) 3 4 Control
More informationLCN 9740 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9740 series operator is shipped with motor gearbox, control box, regular arm, header, and mounting hardware. Actuators available separately, see
More informationSENIOR SWING UNIQUE FEATURES
SENIOR UNIQUE FEATURES Digital Control Suite Provides exceptionally precise control of a large range of built-in functions combined with superior durability and performance. Visual indications and digital
More informationT57 SERIES LOW ENERGY OPERATOR INTRODUCTION FEATURES BENEFITS PATENTS TABLE OF CONTENTS
INTRODUCTION A reliable ADA solution for moderate traffic applications, the T57 Low Energy Operator comprises Norton s heavy-duty 1601 door closer. The use of a hydraulic closer ensures quiet and consistently
More informationMulti-feature closers with compact design, ideal for application on interior doors DOOR CLOSER CATALOG
Multi-feature closers with compact design, ideal for application on interior doors 1700BC E R I E DOOR CLOER CATALOG 1700BC ERIE LIGHT COMMERCIAL DOOR CLOER INTRODUCTION Norton 1700BC eries Door Closers
More informationHIGH SECURITY SERIES
HIGH SECURITY SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide is based
More informationTS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH)
Surface applied door closer Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) TABLE OF CONTENTS Technical specifications Size selection chart 2 Closer setup
More informationHigh Security Closers Series
High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can
More information2850 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting
Features The 2850 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operator when activated, opens doors automatically for wheelchair access, yet allows
More informationDC3000 Series. Door Closers
Door Closers Table of Contents Applications 2 Features 3 & 4 Mountings 5 & 6 Door Closer Arms 7 & 8 Mounting Brackets 9 Brackets and Covers 10 Size and Handing 11 How to Order 12 Quick Codes 13 Helpful
More informationHIGH SECURITY CLOSERS SERIES
HIGH SECURITY CLOSERS SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide
More information9560 Series Senior Swing. Features. Special Templates. Cover Fasteners Mounting. Certifications
Senior Features The 9560 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet
More information1600 SERIES ALUMINUM STOREFRONT DOOR CLOSERS
INTRODUCTION The 1600 Series door closers offer proven quality, performance and reliability unmatched by the competition. A staple in the industry, these ANSI/BHMA Grade 1 closers are designed for exterior
More information9550 SERIES FEATURES OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS
MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS 9550 SERIES The 9550 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated,
More informationD O O R C L O S E R S
DOOR CLOSERS DOOR CLOSER Philadelphia Hardware Group, Inc. is presenting the finest ADVANTAGE surface mounting door closers certified by BHMA including: Multi-size door closer: 9000, 8000, 6000, 6000S
More informationPFT-61 LH & RH Sidelite Transom Patch Fitting w/stop & Fin Installation Instructions
PFT-61 LH & RH Sidelite Transom Patch Fitting w/stop & Fin Installation Instructions For Installation Assistance, Call 855.594.6989 www.assaabloyglass.us Tools Needed: Torque Wrench and Bit Screwdriver
More information5300 Series 5300 SERIES
5300 Series Hager 5300 Series Grade 1 door closer is ideal for schools, hospitals, and other high abuse and high traffic environments. It is constructed of an aluminum alloy and provides smooth door control.
More informationLCN 9540 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors
More informationAn ASSA ABLOY Group brand Series. Architectural Door Closer
An ASSA ABLOY Group brand 3000 Series Architectural Door the perfect choice The Yale 3000 Series Architectural Door s offer the perfect combination of reliability, appearance and durability in today s
More informationHolder/Release Devices with Integral Door Closers DORMA EMF/ EMR
Holder/Release Devices with Integral Door Closers DORMA EMF/ EMR DORMA EMR Holder/Release Device with Integral Detector The DORMA EMR Series holder/release device incorporates a photoelectric detector
More informationROFU TJ 152-A. Y ALE SECURITY GROUP 50BC Series Door Closer. 50BC Series Door Closers. Sizing Chart for Installations. Ordering Information
ROFU 50BC Series Door Closers Specifications U.L. Listing All Yale 50 Series Door Closers with non-hold-open arms are listed by Underwriters Laboratories, Inc. for use on labeled fire doors. Tri-Pack Closer
More informationD-1610/D-1611 SERIES: DOOR CLOSERS. D-1610/D-1611 Series. Door Closers. Trusted experts. Proven reliability. Simply STANLEY.
D-1610/D-1611 SERIES: DOOR CLOSERS D-1610/D-1611 Series Door Closers Trusted experts. Proven reliability. Simply STANLEY. TABLE OF CONTENTS General Information...2, 3 Standard Application...4 Parallel
More informationD o o r C l o s e r s
Door Closers DOOR CLOSER Philadelphia Hardware Group, Inc. is presenting the fi nest ADVANTAGE surface mounting door closers for your various application demands. There are Multi-size door closer: 9000,
More informationInstallation Instructions. Non Hold Open Models. Sized (Sizes 2,3,4,5) Weaker BC 9303BC 9304BC 9305BC. Stronger +
O Right Hand RH eft Hand Reverse HR eft Hand H Right Hand Reverse RHR eft Hand H Right Hand Reverse RHR Regular rm ee Page Top Jamb ee Page Parallel rm ee Pages 3 & UTION Instructions Non Hold Open Models
More informationPULL SIDE MOUNTED PUSH SIDE MOUNTED DOUBLE LEVER ARM LEVER ARM P DOUBLE LEVER ARM SINGLE LEVER ARM 4110T 4210T*
4000 SERIES PRODUCT SELECTION GUIDE Surface mounted 4000 Series LCN closers feature a modern design engineered for each application, easy installation, and superior performance. This guide is based on
More information7500/7700 SERIES. Institutional Door Closer
Institutional Door Closer Page Revised Electronically 5/13, 10/13 7500/7700 SERIES overview The 7500 Series Door Closer offers customers the ideal combination of superior performance, strength and quality.
More informationMODEL 600LB 600 POUND SINGLE MAGNETIC LOCK WITH LED, BOND SENSOR & DOOR STATUS SENSOR SPECIFICATIONS
MODEL 600LB 600 POUND SINGLE MAGNETIC LOCK WITH LED, BOND SENSOR & STATUS SENSOR SPECIFICATIONS U.L. LISTED, LISTING NUMBER R16759 600 POUND MINIMUM HOLDING FORCE MAGNET SIZE 9-7/8 L x 1-11/16 H x1 W SIZE
More information422 Series. Cam Action Door Closer
Cam Action Door Closer Copyright SARGENT Manufacturing Company 2005-2018. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is
More informationACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS
II 1400-10 ACSI MODEL 1406BB-04-AO POWER SUPPLY INSTALLATION INSTRUCTIONS Features: Up to 1.95 Amps Load Capacity Class 2 Rated Outputs Overload, Over Voltage, and Short Circuit Protection Standby Battery
More information*24213* 4040-SE Sentronic. 1 Voltage. 6 Adjusting Hold-Open Door Position. 7 Regulation. 2 Tracking. 8 Door Closer Cover.
*223* 223 00-SE Sentronic Installation Instructions This closer features two mounting options. Before beginning, determine which type of mounting best applies to your application, or had been specified
More informationSeries 2003T. Belt Drive Telescoping Slide Door INSTALLATION INSTRUCTIONS. To be used with H210 C2150 Ver.10 Control Setup Instructions
Series 2003T Belt Drive Telescoping Slide Door INSTALLATION INSTRUCTIONS To be used with H210 C2150 Ver.10 Control Setup Instructions DIRECTION OF DOOR OPENING G230T, JUNE 2009 A U T O M A T I C S G230T.1
More informationUSERS GUIDE LO-21U LOCKOUT RELAY
USERS GUIDE LO-21U LOCKOUT RELAY PRODUCT DESCRIPTION The LO-21U (PN: 10LO21U) is a micro-processed lock out module designed to operate on swing door applications with BEA s Bodyguard or DK-12 overhead
More information2860 SERIES FEATURES OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE
OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE The 2860 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when
More informationPUSH SIDE M O U N T E D PULL SIDE M O U N T E D D O U B L E LEVER ARM LEVER ARM P D O U B L E LEVER ARM S I N G L E LEVER ARM
4000 SERIES PRODUCT SELECTION GUIDE Surface mounted 4000 Series LCN closers feature a modern design engineered for each application, easy installation, and superior performance. This guide is based on
More informationDesign Guidelines and Standards Manual University of Cincinnati
SECTION 08710D - A. SPECIFICATIONS FORMAT 1. It is preferred that this section include all items of door hardware. Window hardware and operators should be specified in the window section. This approach
More informationLCN 4010T SERIES HINGE (PULL) SIDE
HINGE (PULL) SIDE MOUNT The 4010T SMOOTHEE is LCN s best performing heavy duty track closer designed specifically for interior doors in institutional and other rugged high traffic applications. FEATURES
More information*PULL SIDE mount shown
MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS The 9550 SENIOR by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR operators when activated, opens
More informationInstallation Instructions CAUTION
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationDoor Closers. DC8000 Series
Door Closers DC8000 Series Introduction Applications High-quality product and innovative design are the foundations of Corbin Russwin s long history and reputation. That tradition continues with the new
More informationMOUNTING FINISH COVER CYLINDER **ARM FUNCTION REGULAR (DOUBLE) DESIGNER METAL NON-HANDED NON-SIZED
HINGE (PULL) SIDE MOUNT LCN 4010 SERIES The 4010 SMOOTHEE is LCN s best performing heavy duty closer designed specifically for institutional and other rugged high traffic applications. FEATURES Ten Million
More information