Installation Instructions. Non Hold Open Models. Sized (Sizes 2,3,4,5) Weaker BC 9303BC 9304BC 9305BC. Stronger +

Transcription

1 O Right Hand RH eft Hand Reverse HR eft Hand H Right Hand Reverse RHR eft Hand H Right Hand Reverse RHR Regular rm ee Page Top Jamb ee Page Parallel rm ee Pages 3 & UTION Instructions Non Hold Open Models tronger ized (izes,3,,) n Incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should be followed to avoid the possibility of misapplication or misadjustment. UTION NOTE: For special applications a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only. s should be hung on ball bearing or antifriction hinges. separate door stop is recommended. and frame must be properly reinforced. djust closing time speed between 3 and seconds from 90 to 0. These door closers should NOT be installed on the exposed side (weather side) of exterior doors eries Non Handed loser O Regular rm Top Jamb Parallel rm Regular rm ee Page Top Jamb ee Page Parallel rm ee Pages 3 & eft Hand H Right Hand Reverse RHR Right Hand RH eft Hand Reverse HR Right Hand RH eft Hand Reverse HR elf Drilling crews Wood and Metal (Optional) leeve Nut and olt # 3/" Metal /0 tandard omponents Wood For Wood drill 3/ hole Machine crews # Drill, /0 Tap Drill 9/3 thru from loser ide 3/8 Drill other side Thru olt and Grommet Nut Drill 9/3 thru from loser ide 3/8 Drill other ide Optional omponents loser ody Regular rm/top Jamb hoe Main rm 9388 Plate loser ize tamp ""Valve ""Valve onnecting Rod Forearm crew rm ssembly rm lide offit Plate 938 offit Plate Used with Parallel rm losers Only opyright 00, 0 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0)

2 9300 eries Non Hold Open losers Regular rm O Parts () 3/ () 3 / (3) 3/ (9) 9/ (30) Right Hand hown /8 () D R 3 Inches (mm) Opening To 00 0 to 0 to 80 Dimension "" (8) () 3/ (89) /Wall/Hardware/Jamb conditions permitting weep atch 90 E F ackcheck tronger Don't completely close valve crew pinion cap onto pinion shaft by hand or with a Phillips screw driver DO NOT OVER TIGHTEN. opyright 00, 0 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0)

3 9300 eries Non Hold Open losers Parallel rm O Parts Right Hand hown 3/ (0) 3/8 (0) (0) / () / (3) Opening To 00 0 to 30 3 to 80 9/ (3) 3/ (9) 3/ () 9388 Plate Optional /8 (9) /8 () /8 (0) /Wall/Hardware/Jamb conditions permitting 8/8 (9) /8 (8) /8 (30) Holes for 9388 Plate only Inches (mm) Top of (8) (0) / (38) /8 Frame () 3/ (83) / (3) 3/ 9/ (9) (30) lose Valves 3 atch weep Place rm on pindle Rotate Remove rm from pindle opyright 00, 0 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited. 3 ee tep on Page (0)

4 9300 eries Non Hold Open losers Parallel rm O Open Valves ssemble rm 8 Right Hand eft Hand Flat or R R Flat Do Not ack Valves Out ompletely rm crew 9 weep 0 / (38) atch ackcheck 3 tronger opyright 00, 0 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited. Don't completely close valve crew pinion cap onto pinion shaft by hand or with a Phillips screw driver DO NOT OVER TIGHTEN (0)

5 R 9300 eries Non Hold Open losers Top Jamb rm Parts 9/ (30) 3/ (9) O Top of / (38) 3/ () () / (3) E 90 3 Inches (mm) Opening weep To 00 0 to 0 to 80 Right Hand hown /Wall/Hardware/Jamb conditions permitting Dimension "" / (9) () 3/ (89) longer connecting rod is required for reveals greater than 3" () atch Reveal D F ackcheck crew pinion cap onto pinion shaft by hand or with a Phillips screw driver DO NOT OVER TIGHTEN. tronger Don't completely close valve opyright 00, 0 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0)

6 9300 eries djustments weep atch O (Use /8" Hex Wrench for these djustments) ackcheck tronger 0 0 OED To identify your model: rm Placement in hoe ize ode Date ode / % tronger G or =930 3=9303 =930 =930 or / % opyright 00, 0 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited. O 3000 Highway East Monroe, N 8 Tel: (8) 9 Fax: (800) (0)