*24213* 4040-SE Sentronic. 1 Voltage. 6 Adjusting Hold-Open Door Position. 7 Regulation. 2 Tracking. 8 Door Closer Cover.
|
|
- Alaina Lindsey
- 6 years ago
- Views:
Transcription
1 *223* SE Sentronic Installation Instructions This closer features two mounting options. Before beginning, determine which type of mounting best applies to your application, or had been specified for the job; then be sure to use the proper template. Voltage The voltage shown on the track cover plate must match voltage supplied to door frame (2V or 20V). If concealed wiring is wanted, prepare the frame to specifications shown on the corresponding template (pull side or push side). If surface wiring is desired, be sure to mount track on frame before running any EMT/ conduit. 2 Tracking Depending on mounting used, insert proper track plugs into the side or top of the track. Using fasteners provided, mount track on frame to the dimensions of the template being used. Remove solenoid cover plate and make electrical connections (see pg. 2). LL NOTE: Switch hole in the cover plate MUST be aligned with the test/release switch when reattaching the plate to the track. Adjusting Hold-Open Position Remove the screw in the adjustable arm, and open the door to the desired position. Reinsert the screw and tighten securely. 7 Regulation Do not allow the door to slam into the frame. A normal closing time from a 90 position is 5 to 7 seconds, evenly divided between MAIN and LATCH SPEED. If adjustments are needed, use a 3/32 hex wrench. To adjust the MAIN SPEED, turn regulating screw (see illustration below) clockwise to slow the speed or c.c.w. to increase the speed. LATCH SPEED is adjusted in the same way. When adjusting BACKCHECK, turn the regulating screw clockwise to increase the amount of force or c.c.w. to reduce the amount of force. LL NOTE: Do not use an abrupt backcheck setting or expect the door closer to act as a stop! 3 Spring Power Before mounting closer, the spring power may need adjusting. Refer to the label on the closer spring tube. The 00 SE comes preset at size 3. This will control a door up to 38 wide. If your door is wider than 38, adjust closer as shown (see illustration to the right), up to 7 full turns. Starting the cover screws at this point is recommended. Using fasteners provided, mount the closer onto the door to the template dimensions being used. Arm Installation Place the arm spacer over the top shaft of the closer. Install the arm as follows: a Push Side Mounting Place the arm hub over the top closer shaft, parallel with your door. Place a wrench on the bottom shaft of the closer, and rotate away from the door. When flats in the arm hub line up with the first available flats of the shaft, slide the arm hub onto the shaft. Insert the shaft screw and tighten securely. b Pull Side Mounting Place the arm hub over the top closer shaft, parallel with the door. Rotate the arm away from the door until flats in the arm hub line up with first available flats of the shaft. Slide the arm hub onto the closer shaft. Insert the shaft screw and tighten securely. 5 Set Screw in Arm Loosen the set screw in the arm. Connect the art to the track roller, and tighten the set screw firmly. 8 Closer Cover With regulation done, place snap-on clip insert into the proper cutout, then snap the cover assembly onto the spring tube. Caution IMPROPER INSTALLATION OR REGULATION MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. FOLLOW ALL INSTRUCTION CAREFULLY. For questions, call LCN at Maximum Opening Force = 35 ft-lbs 8 N-m 2 N Backcheck Latch Backcheck Main Latch Main NO MAINTENANCE REQUIRED To Increase Power ⁵ ₃₂ Hex Wrench
2 warning (TOP) (TOP) PLATE PLATE END END ADJUST. ADJUST. SPACER SLIDE SLIDE ROLLER SE SE ROLLER SET (SIDE) (SIDE) SET SHAFT SHAFT SE SE SNAP ON PULL PULL SIDE SIDE CLIP INSERT CLIP INSERT MOUNTING MOUNTING (R.H. (R.H. or L.H.) or L.H.) 00 SENTRONIC 00 SENTRONIC CLOSER CLOSER PUSH PUSHSIDE SIDE MOUNTING MOUNTING SOLENOID TERMINAL LEADS GROUND TERMINAL WIRING DIAGRAM - POLARITY NOT IMPORTANT TO EITHER TERMINAL OPTIONAL SWITCH TO EITHER TERMINAL HOLD-OPEN FORCE ADJUSTMENT RELEASE TEST SWITCH CONDUIT HOLE INPUT VOLTAGE: 2V AC/DC OR 20V AC/DC (usually from alarm panel or detector) Hold Open Force Adjustment: Locate the hold-open adjustment screw in the diagram above. For greater hold-open force, insert a socket screw key wrencyh (included in the screwpack), and turn clockwise. To decrease the amount of hold-open force, turn the screw counter-clockwise. Turn a maximum of turns. Electrical checkout. With power on, open the door complete. The door should remain in the open position. If the door does not stay open, Check the electrical input. 2. Push the release test switch. The door should close immediately. Open the door to the hold-open position, and let it remain there. 3. The system should be checked at frequent intervals.
3 00Se Hinge Face Mounted warning DOOR HOLDER SOLENOID DATA 00SE } 2 VAC - DC Nominal =0% - Amp.Max. 20VAC DOOR - DC Nominal HOLDER =0% SOLENOID - DATA.030 Amp. Max. 00SE Auxiliary } Recommended 2 VAC - DC Nominal =0% - Amp.Max. 20VAC - DC Nominal =0% - Amp. Max. Auxiliary Recommended ¹ ₄ Hole for Electrical Connector if ¹ ₄ Hole for Electrical Connector if 2¹ ₄ 2³ ₄ See 2¹ ₄ Note ¹ ₈ ⁷ ₈ 2³ ₄ See Note ¹ ₈ ⁷ ₈ 85 to 0 Hold Open 85 to 0 Hold Open Templating for Left Hand Templating for Left Hand ¹ ₄ Hole for Electrical Connector if 2¹ ₄ ⁷ ₈ ¹ ₈ 2³ ₄ See Note 3 Templating for Right Hand Notes: Inch ¹ ₈ ¹ ₄. Voltage supplied to the ⁷ ₈ unit ¹⁵ ₁₆ MUST match ¹ ₁₆ ¹ ₈ the ¹ ₂ voltage ¹⁵ ₁₆shown 2⁷ ₈ on the 3Sentronic label. 2³ ₄ 2¹ ₄ 2. If the M.M. door 3 is hung 0on pivots: 22 2Locate the closer 29 38and 9track 57from 73the 7 pivot 02 point 52 of the 552 center 7pivotj. For offset pivots: Locate from the pivot point and and add C\,. 3. The floor or wall stops should be used.. If this dimension is greater than ZB\zn, consult the factory. 5. Reinforcing per ANSI/SDI-00 is recommended for hollow metal doors and frames.. If the swing clear hinges are being used, consult the factory. Inch Z\v >\zn B\, Z\, Z\v ZZ\cx Z\x 2 Z\, 2 Z\v 2 M\, >\zn 2 C\, M.M
4 DOOR HOLDER SOLENOID 00SE DATA -Side Mounted 00SE } 85 to 0 Hold Open 2 VAC - DC Nominal =0% - Amp.Max. Auxiliary Recommended 20VAC - DC Nominal =0% - Amp. Max. Warning mounted on ¹ ₄ wide stop 2⁵ ₈ DOOR HOLDER SOLENOID DATA 2 VAC - DC Nominal =0% - Amp.Max. 20VAC - DC Nominal =0% - Amp. Max. ¹ ₄ ³ ₄* ¹ ₄ ³ ₄* Face of on Side Face of on Side 2⁵ ₈ ¹ ₈ Hole for Electrical Connector mounted on ¹ ₄ wide stophinge Edge of 2¹ ₈ C L of Track ¹¹ ₃₂ Header 8⁹ ₁₆ 3 5 3⁷ ₈ Templating for Right Hand ¹ ₈ Hole for Electrical Connector 00SE } 85 2¹ ₈to 0 Hold Open Auxiliary Recommended 3 5 Hinge Edge of Jamb Line of Track C L ¹¹ ₃₂ Header 8⁹ ₁₆ Templating for Right Hand 2⁵ ₈ 3⁷ ₈ Jamb Line 2¹ ₈ Hinge Edge of 5 3 2¹ ₈ 2⁵ ₈ ¹ ₈ Hole for Electrical Connector Face of on Side Hinge C ¹¹ ₃₂ L of Track Edge ³ ₄* ¹ ₄ of 3⁷ ₈ 8⁹ ₁₆ 5 3 Jamb Line ¹ ₈ Hole Templating for Electrical Connector for Left Hand Face of mounted on ¹ ₄ wide stop Notes: on Side. Voltage supplied the unit MUST match the voltage shown on the Sentronic label. 2. The Electrical connector is provided by LCN. 3. Locate the closer and track from the C ¹¹ ₃₂ center line of the pivot or swing - clear the L of hing Track pin, if used.. Floor or wall stops should be used. ³ ₄* ¹ ₄ 5. Reinforcing per ANSI/SDI-00 3⁷ ₈ is recommended 8⁹ ₁₆ for hollow metal doors and frames. Jamb Line Inch Z\v >\zn B\, Z\, Templating Z\v ZZ\cx Z\x for Left 2 Z\, Hand 2 Z\v 2 M\, 3 mounted 5 on ¹ ₄ wide stop 8 >\zn 2 C\, M.M Customer Service Allegion 20 Printed in U.S.A. 223 Rev. 03/-l
5 7.00 Front Back Page Page 2 Page 3 Page.000 BEGINNING SHEET Front folded SHEET Additional Notes: Revision History Revision Description: l > Revised artwork. None J K L M N P N/A Material Notes. printed two sides 2. printed black 3. tolerance ±.3. printed in country may vary 5. drawings not to scale White Paper Edited By Approved By EC Number Release Date D. Myers B. Eickhoff Title Creation Date Created By N/A Software: InDesign CS 00SE Series Instruction Sheet Number 223 Revision l Activity 3899 Hancock Expwy Security, CO 809 Allegion 20
*24771* 4040SE DE Sentronic. 1 Voltage. 7 Regulation. 2 Track. 8 Door Closer Cover. 3 Spring Power. 4 Arm Installation. 5 Arm Screw.
*2477* 2477 SE Egress 4040SE DE Sentronic Installation Instructions This closer features mounting options for both standard and step-down double egress frames. Before beginning, determine which type of
More information*24191* 4040SEL Sentronic. 35 ft-lbs 48 N-m 62 N. Installation CAUTION. Customer Service. Installation Instructions
*24191* 24191 4040SEL Sentronic Installation Instructions Backcheck = Maximum Opening Force 35 ft-lbs 48 N-m 62 N Latch Backcheck Main To Increase Power 5/32 Hex Wrench Main Latch 1a 1b 1c 1d This closer
More informationHOW TO TELL HAND OF DOOR:
*15022* 4410ME Series 15022 Door closer with electronic release & Multi-point hold open Installation Instructions 1 Closer Installation 1a Closer Information Closer is handed at the factory. The hand of
More informationConnected To Control Box Series. Closer. Set Screw. Arm Screw. Right Hand Shown. 1/8" I.D. Air Inlet Tubing Connected To Control Box
*19963* 19963 Auto-Equalizer Low Energy Door Operator 1/8" I.D. Air Inlet Tubing Connected To Control Box Closer 2610 Series Set Screw Arm Screw Track Roller Track Installation Instructions Top Of Door
More information*24828* 1 Installation. Left Hand Shown, Right Hand Opposite. Customer Service
*24828* 4820 24828 Non-Handed/Non-Sized Auto-Equalizer Low Energy Door Operator, Installation and Adjustment of Door Operator Installation Instructions Long Cover Cover Insert Cover Left Hand Door Right
More information*28101* 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT. Table of Contents.
*28101* 28101 4630, 4640 Electric Auto Equalizer Series 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT Table of Contents General Information...2
More information*29268* 4600CS Electronic Low Energy Operator 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT. Table of Contents. Customer Service
*29268* 29268 4630CS, 4640CS Electric Auto Equalizer Series 4600CS Electronic Low Energy Operator Installation Instructions 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT The 4600CS Series electric Auto-Equalizer
More informationTS93 EMF T/PT/TDE. Surface applied door closer
TS9 EMF T/PT/TDE Surface applied door closer Installation instructions: Pull side track mount door closer (no smoke detector) (EMF T) Push side track mount closer (no smoke detector) (EMF PT) Double egress
More informationASSA ABLOY MPI (Infinite Hold Open Range) Support Unit Models. Multi-Point Electromechanical Overhead Concealed Closer Holder Releasing Device
Overhead Concealed Closer Holder Releasing Device with Rigid Slide Arm For wood or metal doors 1-3/4 to 2-1/4" (45-57mm) thick Hung in a hollow metal frame Standard butt hinges Typical Installation One
More informationFIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES
FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke
More informationFIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE
FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke barrier doors.
More informationLCN 4310ME SERIES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled. closer/holder designed to provide
HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide FEATURES infinitely adjustable hold-open for fire and smoke barrier doors. Door
More information4040XPT Series Door controls
4040XPT Series Door controls Fire Rated: Tested on fire door assemblies in accordance with Australian Standards, refer fire door manufacturer for specific approval details The LCN 4040XPT Series is a non-handed,
More informationLCN 4310ME SERIES FEATURES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled
HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for FEATURES fire and smoke barrier doors. Door
More informationASSA ABLOY Universal Door Closers
Installation Instructions For Non-Hold Open or A Hold Open Arm Options DC6200 Series DC6400 Series Multi-Sized thru 6 Half-Size thru 6 Regular Arm Parallel Arm Universal Door Closers Jamb Mount See pages
More informationElectro-Mechanical Swing Operator. Table of Contents
*640072* 640072 Electro-Mechanical Swing Operator Models 8230 & 8240 Installation Instructions Table of Contents General...1 Replacement Parts & System Components...1 1 Pre-Installation Site & Product
More informationNON-SIZED SIZED HANDED
HINGE (PULL) SIDE MOUNTING 4310ME SERIES The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.
More informationCONCEALED CLOSER SERIES
CLOSER SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of
More informationDOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM
SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of the closer.
More informationCONCEALED CLOSER SERIES
CONCEALED CLOSER SERIES APPLICATIONS n For aluminum, hollow metal, or wood doors and frames. n Can be used with hinge or pivot mounted door. n Closers for 4 or minimum 1-3/4 head frame or 4 top rail. n
More informationNON-SIZED SIZED HANDED
4040SE SERIES n Standard 4040SE Series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks are optional,
More informationNON-SIZED SIZED HANDED
4410ME SERIES TOP JAMB (PUSH SIDE) MOUNTING The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.
More informationLCN 4040SE SERIES FEATURES HINGE (PULL) SIDE MOUNTING
HINGE (PULL) SIDE MOUNTING Standard 4040SE series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks
More informationSeries 9540 J9540. Installation Instructions Multi-Sized 1 to 6 Non-Hold Open. Regular Arm Applications. Parallel Arm Applications
Series 940 J940 ASSA JL940 ABLOY Installation Instructions Multi-Sized to 6 Non-Hold Open Regular Arm Applications Left Hand Regular Arm Application Contents Page Template Template with 984-8 Drop Plate
More informationTS9356 PKT 90/119. Surface applied door closer. Installation instructions: Pocket door track mount in 90 /119 pocket (Closer on wall)
TS96 PKT 90/9 Surface applied door closer Installation instructions: Pocket door track mount in 90 /9 pocket (Closer on wall) TABLE OF CONTENTS Closer overall Technical specifications Door templates Closer
More informationInstallation Instructions Series 78-B/FHA Hold Open
Installation Instructions Series 78-B/FHA Hold Open Traditional Style Door Closers Read these instructions before proceeding with the installation. Make sure that the door opens the full angle desired
More informationDC3210 Series. Multi-Sized 1 thru 6 DEEP REVEAL APPLICATION WITH M103 OPTION(615F59 CLAMP KIT) Recommended Closer Size
DC310 Series Multi-Sized 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH DEEP REVEAL APPLICATION WITH M103
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More informationLCN 4010T SERIES HINGE (PULL) SIDE
HINGE (PULL) SIDE MOUNT The 4010T SMOOTHEE is LCN s best performing heavy duty track closer designed specifically for interior doors in institutional and other rugged high traffic applications. FEATURES
More informationASSA ABLOY Universal Door Closers with Heavy Duty Spring Stop Parallel Arms
DC610 Series Multi-Sized 1 thru 6 DC610 Series Half-Size 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH
More information9530 Series Senior Swing. Features. Special Templates. Fasteners Mounting. Certifications
Features The 9530 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows
More information4031 Series Door controls
4031 Series Door controls Fire Rated: Tested on fire door assemblies in accordance with Australian Standards, refer fire door manufacturer for specific approval details The 4031 Series is a non-handed,
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions
More informationOverhead door holders/ stops
Overhead door holders/ stops Quality hardware for superior door control Known throughout the industry as the overhead door holder specialist, Glynn-Johnson has made its name with state-of-the-art manufacturing
More information7100SZ Series SafeZone Installation and Instruction Manual
7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 80-9371-0081-00 (10-10) Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 5 for template) 3 1 Push Side Applications
More information9550 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting
Senior Features The 9550 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet
More informationADA EZ Rev. H, 8/23/11
Installation and Operating Instructions ADA EZ Installation and Operating Instructions EZ040 Note Changes or modifications not expressly approved by the party responsible for compliance could void the
More informationHIGH SECURITY CLOSERS SERIES
HIGH SECURITY CLOSERS SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide
More information4310ME Series. Features E25. Special Templates. Grade 1 - ANSI A156.15, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act, NFPA 101
Features The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until current
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO
More informationHIGH SECURITY SERIES
HIGH SECURITY SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide is based
More information4310ME Series. Features E25. Special Templates. Certifications. Cover Fasteners Mounting Arms
4310ME Features The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until
More information4040XP Series Door controls
4040XP Series Door controls Fire Rated: Tested on fire door assemblies in accordance with Australian Standards, refer fire door manufacturer for specific approval details The LCN 4040XP Series is a non-handed
More informationHeadline. Overhead Door Holders/Stops
Headline Overhead Door Holders/Stops Quality hardware for superior door control 2 Glynn-Johnson has been providing the highest quality door control hardware for 75 years. Known in the industry as the overhead
More information1461 Series Door controls
1461 Series Door controls Fire Rated: Tested on fire door assemblies in accordance with ustralian Standards, refer fire door manufacturer for specific approval details The LCN 1461 Series is a non-handed
More information9550 SERIES FEATURES OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS
MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS 9550 SERIES The 9550 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated,
More informationHigh Security Closers Series
High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can
More informationAllegion LCN Benchmark AU9100 Series
Allegion LCN Benchmark AU9100 Series Low Energy Operators Installation Manual LCN Low Energy Operators should be installed in accordance with the current Allegion LCN installation instructions. Commissioning
More information9540 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9540 SERIES The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated,
More information*HINGE (pull) side mount shown
CLOSER MOUNTS *HINGE (PULL) SIDE TOP JAMB (PULL SIDE) STOP FACE (PUSH SIDE) The 4040T SMOOTHEE is LCN s most flexible heavy duty track closer designed specifically for interior doors in institutional and
More information* * M400 Series Double Locks. Double Electromagnetic Locks: M422, M452, M492. Installation Instructions. Mounting Bracket (2)
*44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Mounting Bracket (2) Inside Mounting Bracket Screws** (4) Mounting Bracket Screws**
More information9560 Series Senior Swing. Features. Special Templates. Cover Fasteners Mounting. Certifications
Senior Features The 9560 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet
More informationSENIOR SWING UNIQUE FEATURES
SENIOR UNIQUE FEATURES Digital Control Suite Provides exceptionally precise control of a large range of built-in functions combined with superior durability and performance. Visual indications and digital
More information*PULL SIDE mount shown
MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS The 9550 SENIOR by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR operators when activated, opens
More informationSERIES 1370 DOOR CLOSERS
SERIES 1370 DOOR CLOSERS LCN 1370 Series The LCN Quest 1370 Series is the Fastest Closer Ever Installed. The LCN Quest features a contemporary design with the unique Rapidor mounting bracket, stick-on
More informationBALANCER DOOR WITH GEARBOX TENSIONER
INSTALLATION INSTRUCTIONS BALANCER DOOR WITH GEARBOX TENSIONER Phone: (800) 421-6144 Fax: (800) 587-7501 crlaurence.com usalum.com crl-arch.com 11M0219_REV_A ORDER OF ASSEMBLY AND INSTALLATION INTRODUCTION...
More informationLCN 9540 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors
More informationKEANE MONROE a member of the record group
SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully
More informationHigh Security Closers Series
High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can
More informationElectrohydraulic Powered Systems
Electrohydraulic Powered Systems ELECTRIC AUTO EQUALIZERS These Auto Equalizer products are an addition to the original pneumatic drive system. People moving through a door can use it as a normal rack
More informationLCN 9740 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE
SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9740 series operator is shipped with motor gearbox, control box, regular arm, header, and mounting hardware. Actuators available separately, see
More informationMetal, Standard Wood and machine screw pack Top jamb (Push Side) Body Construction. Finishes/Colors/ Powder Coat. Wiring NON-SIZED SIZED
Features The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until current
More information5600 Series Power Operator Installation and Instruction Manual
5600 Series Power Operator Installation and Instruction Manual 80-956-000-00 (08-) 5 ASSA ABLOY 6 Item No. Description Motor (5600M) Cover (5600COV) Control Inverter (5600IN) Power Supply VDC (5600PS)
More informationTS93 PT/PTH. Surface applied door closer. Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH)
Surface applied door closer Installation instructions: Push side track mount with dead stop (PT) Optional hold open (PTH) TABLE OF CONTENTS Technical specifications Size selection chart 2 Closer setup
More informationHinge (Pull) Side Door Application DC6230 Series Multi-Sized 1 thru 6 DC6430 Series Half-Size 1 thru 6. Door Mounted DC6230 & DC6430
Installation Instructions Universal Door Closers Slide Track Application (0 Maximum Door Swing) (standard)- N.H.O. Bumper Stop A - H.O. Bumper Stop Track - Pull Side See pages 2 & Hinge (Pull) Side Door
More informationLCN AUTOMATIC OPERATORS
LCN AUTOMATIC OPERATORS SENIOR 9530 SENIOR 9540 SENIOR 9550 SENIOR 9560 8310 ACCESSORIES LCN ELECTROMECHANICAL POWERED SYSTEMS ELECTROMECHANICAL AUTOMATIC OPERATORS LCN s electromechanical products are
More informationMOUNTING FINISH COVER CYLINDER **ARM FUNCTION REGULAR (DOUBLE) DESIGNER METAL NON-HANDED NON-SIZED
HINGE (PULL) SIDE MOUNT LCN 4010 SERIES The 4010 SMOOTHEE is LCN s best performing heavy duty closer designed specifically for institutional and other rugged high traffic applications. FEATURES Ten Million
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
More information*4110 HCUSH mount shown
*PARALLEL ARM (PUSH SIDE) MOUNT The 4110 SMOOTHEE is LCN s best performing heavy duty closer designed specifically for institutional and other rugged high traffic applications. FEATURES Standard 4110 series
More information2850 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting
Features The 2850 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operator when activated, opens doors automatically for wheelchair access, yet allows
More informationStandard closer offers 3 installation options. - Regular (Pull side) - Top Jamb (Push side) - Parallel Arm (Push side)
The LCN is a non-handed surface mounted closer designed for maximum versatility. wide choice of options, mounting accessories and ease of installation make this a fully universal closer. The LCN has been
More informationConcealed overhead closer for high-end applications DOOR CLOSERS CATALOG
Concealed overhead closer for high-end applications 7900 S E R I E S DOOR CLOSERS CATALOG INTRODUCTION The 7900 Series Overhead Concealed Closers offer extremely durable operation with the vandal resistance
More informationDoor Closer Cycle. How to Select the Proper Closer. Things to Consider
Door Control Closer Spring Adjustment Not Shown in Door Closer Cycle Diagram Effects the entire cycle of the door closer movement Used to size closer for application requirements Determines the amount
More information*70954* 240V Senior Swing Control Box Installation Instructions CAUTION WARNINGS. Table of Contents
*70954* 70954 2800 Overhead Concealed eries 9500 urface Applied eries 240V enior wing Control Box Installation Instructions CAUTION These instructions are presented in step-by-step sequence. It is very
More informationM400 Series Double Locks. Features
*44487304* 44487304 M400 Series Double Locks Double Electromagnetic Locks: M422, M452, M492 Installation Instructions Automatic Voltage Selection (AVS) Magnet immediately detects 12VD or 24VD when power
More informationPFadvantage JD 3300/4400/6600/7700; 4420
Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6
More informationLCN 2810 SERIES OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED CENTER PIVOT ARM OFFSET PIVOT/BUTT HINGE
OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE The 2810 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when activated,
More information*ININST.1039* 2390 Touchbar
*ININST.1039* ININST.1039 Concealed Vertical Rod Panic Device 2390 Touchbar Installation Instructions Index Parts List... 2 Before Installation... 5 Installation... 5 RX Device Wiring... 12 EL Device Wiring...
More information*CENTER PIVOT arm shown
OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE *CENTER PIVOT arm shown 2860 series operator is shipped with motor gearbox, control boxes, bottom pivots, arms,
More informationPatriot. Aluminum and Steel 5spring. Step #1 Tarp Spool with Gear Motor (Includes Instructions for Optional Wind Deflector)
Aluminum and Steel 5spring Qty. Component Parts Description: LONG BOX: (1) 103 Aluminum Tarp Axle (2) 98 Upper Arms with 90 Degree Elbow (2) Lower Aluminum ( 84 ) (1) Aluminum Cross Tube SMALL HARDWARE
More informationASSA ABLOY Series Multi-Point Hold Open Installation and Instruction Manual
Pull Side Applications with Slide Track (7210, 7250) (see page 7 for template) 7200 Series Multi-Point Hold Open Installation and Instruction Manual 3 1 Push Side Applications with Double Lever Arms (7220,
More information2860 SERIES FEATURES OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE
OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE The 2860 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when
More informationPULL SIDE MOUNTED PUSH SIDE MOUNTED DOUBLE LEVER ARM LEVER ARM P DOUBLE LEVER ARM SINGLE LEVER ARM 4110T 4210T*
4000 SERIES PRODUCT SELECTION GUIDE Surface mounted 4000 Series LCN closers feature a modern design engineered for each application, easy installation, and superior performance. This guide is based on
More informationRTS88. Overhead Concealed Door Closer
RTS88 Overhead Concealed Door Closer RTS88 OVERHEAD CONCEALED CLOSER DORMA RTS88 OVERHEAD CONCEALED DOOR CLOSER Invisible door control Dependable and easy to install Architects are often challenged to
More informationCopyright , 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express
over he ad conce aled closer s o v e r h e a d c o n c e a l e d c l o s e r s i n t r o d u c t i o n i n t r o d u c t i o n Rixson Overhead Concealed closers offer an aesthetically appealing way to
More informationLCN Super Smoothie Adjustable Closer Super Smoothie Adjustable Closer
4041 Super Smoothie Adjustable Closer Parallel Arm Mount Shown 4041 Super Smoothie Adjustable Closer The 4041 SUPER SMOOTHIE is a heavy duty, double lever arm closer for institutional and other high traffic
More information268, 269 & 278. Concealed Door Closers
268, 269 & 278 Concealed Door Closers Copyright 2004-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents General Information....3 268 Features and Benefits...4
More information* * M400 Series. Features. Models. Trims. UL Requirements. Single Electromagnetic Locks: M420, M450, M490. Installation Instructions
*44487296* M400 Series 44487296 Single Electromagnetic Locks: M420, M450, M490 Installation Instructions M420/M450 Armature plate assembly M490 Armature plate assembly Features Automatic Voltage Selection
More informationD-1610/D-1611 SERIES: DOOR CLOSERS. D-1610/D-1611 Series. Door Closers. Trusted experts. Proven reliability. Simply STANLEY.
D-1610/D-1611 SERIES: DOOR CLOSERS D-1610/D-1611 Series Door Closers Trusted experts. Proven reliability. Simply STANLEY. TABLE OF CONTENTS General Information...2, 3 Standard Application...4 Parallel
More information920 Remote Control Switches
920 Remote Control Switches REMOTE CONTROL SWITCHES Service Bulletin This service bulletin for ASCO 920 Remote Control Switches explains how to replace the main s, operator coil, control s, and how to
More informationDoor Closers. DC8000 Series
Door Closers DC8000 Series Introduction Applications High-quality product and innovative design are the foundations of Corbin Russwin s long history and reputation. That tradition continues with the new
More informationSAFETY REASONABLE EFFORT. ANY BINDING, SAGGING, LOOSE HINGES, OR DAMAGED HINGES MUST BE REPAIRED BEFORE CONTINUING WITH THIS INSTALLATION!
Commercial Gentleman Door Operator Installation Instructions SAFETY THE COMMERCIAL GENTLEMAN IS A LOW ENERGY DOOR OPENER. PROPERLY ADJUSTED, THIS OPENER SHOULD BE EASY TO STOP WITH YOUR LITTLE FINGER.
More information*CENTER PIVOT arm shown
OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE *CENTER PIVOT arm shown 2910 series operator is shipped with motor gearbox, control box, arm, bottom pivot, header,
More informationDor-O-Matic. Senior-Swing Universal Control Box. Instruction Manual Universal Control Box DOR-O-MATIC
Dor-O-Matic Senior-Swing Universal Control Box Instruction Manual 85445-900 Universal Control Box Factory Authorized Door Leaf Size & Weight: Type Width per Leaf Max. Weight per Leaf Single Door 36" to
More information5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY
5700 Series Power Operator Hinge (Pull) Side Mount Installation and Instruction ASSA Manual ABLOY 80-957-000-00 (06-5) Patents 5,88,97; 7,6,096; 7,8, 6 5 0 8 7 9 Item No. Description Back plate Door Closer
More information401B/1KDB CoolRite/FreezeRite Installation Manual I003
401B/1KDB CoolRite/FreezeRite Installation Manual 99-16105-I003 Copyright 2011 by ALL rights reserved. Information in this document is subject to change without notice. Companies, names and data used in
More informationDC8000 Series. Door Closers
Door Closers Introduction Applications High-quality products and innovative designs are the foundation for the long history and reputation of Corbin Russwin Architectural Hardware. That tradition continues
More information5300 Series 5300 SERIES
5300 Series Hager 5300 Series Grade 1 door closer is ideal for schools, hospitals, and other high abuse and high traffic environments. It is constructed of an aluminum alloy and provides smooth door control.
More informationGLANCE. Refer to Installation Guide Booklet before attempting to install. Phone:
INSTALLA ALLATION AT T A GLANCE Refer to Installation Guide Booklet before attempting to install. NOTICE: Improper installation voids Warranty. Phone: 800-392-5209 www.precisionhardware.com 630-605 REV.
More informationDC3000 Series. Door Closers
Door Closers Table of Contents Applications 2 Features 3 & 4 Mountings 5 & 6 Door Closer Arms 7 & 8 Mounting Brackets 9 Brackets and Covers 10 Size and Handing 11 How to Order 12 Quick Codes 13 Helpful
More information