SENIOR SWING UNIQUE FEATURES

Size: px
Start display at page:

Download "SENIOR SWING UNIQUE FEATURES"

Transcription

1 SENIOR UNIQUE FEATURES Digital Control Suite Provides exceptionally precise control of a large range of built-in functions combined with superior durability and performance. Visual indications and digital readouts of all control function settings and activity make adjustments easy, fast and accurate. Dual Independent Program Memories Each unit is pre-programmed to factory default settings. The installer can adjust the unit to meet the job site requirements. These field settings are locked into the computer s memory. Any subsequent field adjustments replace the original field adjustments. The factory settings are always retained in memory and can be recalled to replace the field settings in just seconds, restoring the unit to its original programming. Programming Mode Allows tailoring the following functions to meet specific site conditions n Opening Speed n Backcheck Speed n Backcheck Position n Hold Open Delay n Latch Position n Auto Reverse - Closing n Electric Lock Delay n Power Boost n Push N Go n Alternate Action n Safety Slow/Stop n Slow Down Disable On-Board Diagnostics Sophisticated built-in diagnostics program monitors the system microprocessor, power supplies, drive systems, actuators and safety circuits. Reduces the time required to make sure the installation is complete and correct. On-Board Power Supply Provides 24V AC output or 24V DC output with rectifier to power card readers, manual actuators and other peripherals. Plug and Play Sensors Motion sensors and safety sensors feature a plug and play concept allowing fast and accurate wiring connections in only seconds. Electronic Circuit Protection High voltage (primary AC input) is protected by replaceable fuse. Low voltage (secondary AC output) is protected by self-resetting fuses. Visual Function Indicators LED Display allows direct observation of these inputs while in visual function indicator mode: n Key switch- set to Auto, OFF or HOLD n Activate n DMSS approach n DMSS safety n Bodyguard n Power Boost Disable Push N Go Allows pedestrians to walk up to the door and push it open as if it were a manual door. After the door is manually opened approximately 5 degrees, the Push N Go feature takes over and continues to open the door slowly and automatically to the full open position. With Push N Go, the door will stay fully open from one to 30 seconds, depending on the time delay chosen. Auto Reverse A safety feature that reverses the direction of the door when it comes into contact with an object during either opening or closing. Safety Slow/Stops Function Once the door starts opening, any person or object entering the swing area will cause the door to go into a safety slow speed. This function can be set to allow for a short stop once a person or object is sensed. Power Boost Adds an additional latching force to ensure secure latching in severe wind or stack conditions. Power Boost is also ideal for overcoming slowing obstacles such as electric strikes. Provides approximately 25 lbs. of total closing force. Microprocessor Control unit allows for quiet efficiency in operation. Combined with the all electromechanical unit, it eliminates unnecessary wear and prolongs the life of the unit. Electric Lock Delay Causes a 1 second delay between activate signal and door opening to allow time for most electric locks to disengage before operator opens door. 79

2 Notes 80

3 MOUNTS SINGLE, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE 2810 SERIES The 2810 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES n 2810 Series operator is shipped with motor gearbox, control box, arm, bottom pivot, header, and mounting hardware. Actuators available separately, see pages n Single door, overhead concealed. n Meets ADA, requirements (power mode only). n Handed product. *CENTER PIVOT arm shown n 36 header length is standard, specify length 33 to 49 max. n Double door header available up to 98, specify length 49 to 98 max. Consult factory regarding this option. n Fixed (Positive) or breakaway stop available with center pivot arm. n Adjustable hold open time of 1 to 32 seconds. n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Meets International Building Code requirements and ANSI A n UL approved for fire doors Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 2810 Series is UL listed for fire-rated applications. The 2810 Series also meets the provisions of the Americans with Disabilities Act. SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR MOUNTING HANDED NON-HANDED SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE CONCEALED SIMULTANEOUS PAIR CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE LEVER) REGULAR (DOUBLE LEVER) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE 81

4 2810 SERIES MOUNTING DETAILS CONCEALED SINGLE (CENTER PIVOT, EMERGENCY BREAKAWAY, PULL) MOUNTING Minimum header length 33 with applied stop by others and 36 with LCN fixed or breakaway stop. 1" 25 MM EMERGENCY BREAKOUT 3 3/4 " 95 MM INCOMING 3/16" 5 MM 48" OPENING (MAX.) 5 3/4 " 146 MM DIRECTION 4 1/2 " 114 MM 1/8" 3 MM BREAKAWAY STOP BREAKOUT DIRECTION EXTERIOR Shown w/ 3-3/4 pivot CONCEALED SINGLE (CENTER PIVOT, FIXED STOP, PUSH) MOUNTING Minimum header length 33 with applied stop by others and 36 with LCN fixed or breakaway stop. 3 3/4 " 95 MM OUTGOING 5 3/4 " 146 MM FIXED STOP 4 1/2 " 114 MM 1/8" 3 MM 1" 25 MM 48" OPENING (MAX.) 3/16" 5 MM DIRECTION EXTERIOR Shown w/ 3-3/4 pivot MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. n Head Frame minimum 36 (L) x 5-3/4 (H) x 4-1/2 (W) (914 mm x 146 mm x 114 mm). n Top Rail minimum 2 (51 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n Door Stop required for each door panel. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 82

5 2810 SERIES OFFSET PIVOTS or BUTT HINGES 3 3/4" 95 MM OUTGOING SLIDE ARM ASS'Y WITH SLIDE BLOCK 11" SLIDE CHANNEL 10 1/2" 257 MM CONCEALING CHANNEL EXTERIOR 5 3/4" 146 MM 1/8" 3 MM DIRECTION 4 1/2" 114 MM SLIDE ARM ASS'Y CONCEALING CHANNEL FRAME Shown w/ 3-3/4 pivot CONCEALED SINGLE (OFFSET PIVOT OR BUTT HINGE, SLIDE ARM, PUSH) MOUNTING Minimum header length 33. Installations require bottom pivot and two intermediate pivots. MOUNTING DETAILS n Head Frame minimum 33 (L) x 5-3/4 (H) x 4-1/2 (W) (838 mm x 146 mm x 114 mm). n Top Rail minimum 2 (51 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n Door Stop required for each door panel. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Contact LCN Product Support for installation assistance. 83

6 ACCESSORIES 2810 SERIES MOTOR GEARBOX MOTOR GEARBOX SENIOR, Driving mechanism for operator. Provides maximum 15 lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET 3-3/4, Motor gearbox mounting bracket for 3-3/4 offset pivot, butt hinge or center pivot with finger guard installations. Front bracket. MOUNTING BRACKET 2-3/4, Motor gearbox mounting bracket for 2-3/4 center pivot installations. Front bracket. REAR MOUNT BRACKET, Motor gearbox mounting bracket. Rear bracket. CONTROL BOXES CONTROL BOX - SENIOR, Electronic controlling device for Senior Swing. HEADERS HEADER, HL Standard, mounting header. Single door, single operator. Specify length 33 to 49 maximum. HEADER, DD Standard, mounting header. Double door, single operator. Specify length 49 to 98 maximum HL 3572DD END CAPS HEADER END CAPS, End cap with openings for wiring. 334 ARMS CENTER PIVOT ARM, CP (CENTER PIVOT INSTALLATIONS ONLY) Used with overhead concealed operators and center pivoted doors. OFFSET PIVOT ARM, OP (OFFSET PIVOT OR BUTT HUNG INSTALLATIONS ONLY) Used with overhead concealed operators. 3077CP 3077OP OFFSET PIVOT ARM ASSEMBLY COMPLETE OPCM Offset arm with track and concealing channel. (Includes 3072 concealing channel, 168 slide channel and 3077OP offset pivot arm). 3077OPCM OP 84

7 CHANNELS CONCEALING CHANNEL, Used to conceal arm in overhead concealed applications. For offset pivot installations only. If ordering separately specify length and hand. SLIDE CHANNEL, (OFFSET PIVOT or BUTT HINGE INSTALLATIONS ONLY) Mounts in top rail of door. Allows arm to slide. INSTALLATION ACCESSORIES STOP BREAKAWAY, B Allows in-swinging door to swing out in case of emergency. Disables operator in breakaway mode. For center pivoted installations only. STOP FIXED, F Prevents out-swinging door from swinging in. For center pivoted installations only. FILLER PLATE BLANK, Completes length of header box. SPINDLE PLATE 2-3/4, A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2-3/4 center pivot installations. SPINDLE PLATE 3-3/4, B Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 3-3/4 offset pivot, butt hinge or center pivot with finger guard installations. PIVOTS BOTTOM PIVOT ASSEMBLY, Includes pivot body, pivot post and bottom pivot plate. For overhead concealed, center pivoted installations. Includes; , and PIVOT BODY, Bottom pivot body for center pivoted installations. PIVOT POST, Connects pivot body to bottom pivot plate for center pivoted installations. BOTTOM PIVOT PLATE, Applied to floor for center pivoted installations SERIES B 384F 12 11A 11B 3107 ACCESSORIES

8 ORDERING INFORMATION 2810 SERIES TABLE OF SIZES WIDTH 36" 914mm 2811 Minimum Door Width 48" 1219mm Indicates recommended range of door width for operator. NOTE: For all Senior Swing Series. Single Door - Width per leaf 36 minimum, 48 maximum. HOW-TO-ORDER 2810 SERIES S 1. SELECT INSTALLATION TYPE SPECIFY ARM 3-3/4 (Offset pivoted) Arm (3077OP) 2-3/4 (Center pivoted) Arm (3077CP) 3-3/4 (Center pivoted) Arm (3077CP) 3. SPECIFY HAND RH LH 4. SPECIFY HEADER/LENGTH HL (Specify length 33 to 49 offset pivot) HL (Specify length 36 to 49 center pivot) DD (Specify length 49 to 98 ) 5. SPECIFY FINISH Standard Anodized Finish Aluminum or Dark Bronze. Operator will be shipped with: - MOTOR GEARBOX, - CONTROL BOX, - HEADER (at specified Length, 36 standard), - WOOD and MACHINE SCREW PACK Unless options listed below are selected. OPTIONS STOPS* Positive Mechanical Stop (POS) Panic Breakaway Stop (BKY) *Available with Center Pivoted installations only. 86

9 MOUNTS SIMULTANEOUS PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE 2850 SERIES The 2850 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Digital keypad for easy setup. n Meets International Building Code requirements and ANSI A n UL approved for fire doors. *CENTER PIVOT arm shown n 2850 Series operator is shipped with motor gearboxes, control box, arms, bottom pivot, header, and mounting hardware. Actuators available separately, see pages n Simultaneous pair, overhead concealed. n Meets ADA, requirements (power mode only). n Handed for double egress applications only. n 72 header length is standard. Specify other length 52 to 98 max. Consult factory regarding this option. n Optional fixed (POS) or breakaway stop (BKY) available (center pivot arm). Header lengths 70 to 98 max with either (POS) or (BKY) option. n Adjustable hold time period of 1 to 32 seconds Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 2850 Series is UL listed for fire-rated applications. The 2850 Series also meets the provisions of the Americans with Disabilities Act. SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR MOUNTING HANDED* NON-HANDED SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE CONCEALED SIMULTANEOUS PAIR CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE LEVER) REGULAR (DOUBLE LEVER) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE * For double egress only. 87

10 2850 SERIES MOUNTING DETAILS CONCEALED SIMULTANEOUS PAIR (CENTER PIVOT, EMERGENCY BREAKAWAY, PULL) MOUNTING Minimum header length 52 with applied stop by others and 70 with LCN fixed or breakaway stop. 1" 25 MM EXTERIOR EMERGENCY EMERGENCY BREAKAWAY BREAKAWAY 3 3/4 " 3 3/4 " 95 MM 95 MM INCOMING INCOMING 8'-0" OPENING (MAX.) 1" 25 MM 5 3/4 " 146 MM DIRECTION 4 1/2 " 114 MM 1/8" 3 MM BREAKAWAY STOP BREAKAWAY DIRECTION EXTERIOR Shown w/ 3-3/4 pivot CONCEALED SIMULTANEOUS PAIR (CENTER PIVOT, FIXED STOP, PUSH) MOUNTING Minimum header length 52 with applied stop by others and 70 with LCN fixed or breakaway stop. OUTGOING EXTERIOR OUTGOING 5 3/4 " 146 MM 4 1/2 " 114 MM 1/8" 3 MM 3 3/4 " 95 MM 3 3/4 " 95 MM FIXED STOP DIRECTION MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. 1" 25 MM 8'-0" OPENING (MAX.) n Head Frame minimum 52 (L) x 5-3/4 (H) x 4-1/2 (W) (1524 mm x 146 mm x 114 mm). n Top Rail minimum 2 (51 mm). 1" 25 MM EXTERIOR Shown w/ 3-3/4 pivot n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n Door Stop required for each door panel. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 88

11 2850 SERIES OFFSET PIVOTS or BUTT HINGES OUTGOING 11" SLIDE CHANNEL 10 1/2" 267 MM EXTERIOR OUTGOING SLIDE ARM ASS'Y WITH SLIDE BLOCK CONCEALING CHANNEL 3 3/4" 95 MM 5 3/4" 146 MM 1/8" 3 MM DIRECTION 4 1/2" 114 MM SLIDE ARM ASS'Y CONCEALING CHANNEL FRAME CONCEALED SIMULTANEOUS PAIR (OFFSET PIVOT/BUTT HINGE, PUSH) MOUNTING Offset pivot installations require a bottom pivot and two intermediate pivots. MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. MOUNTING DETAILS n Head Frame minimum 52 (L) x 5-3/4 (H) x 4-1/2 (W) (1524 mm x 146 mm x 114 mm). n Top Rail minimum 2 (51 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n Door Stop required for each door panel. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 89

12 ACCESSORIES 2850 SERIES MOTOR GEARBOX MOTOR GEARBOX SENIOR, Driving mechanism for operator. Provides maximum of 15 lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET 3-3/4, Motor gearbox mounting bracket for 3-3/4 offset pivot, butt hinge or center pivot with finger guard installations. Front bracket. MOUNTING BRACKET 2-3/4, Motor gearbox mounting bracket for 2-3/4 center pivot installations. Front bracket. REAR MOUNT BRACKET, Motor gearbox mounting bracket. Rear bracket. CONTROL BOXES CONTROL BOX SENIOR, Electronic controlling device for Senior Swing. COMPANION CABLE, Cable that allows one control box to run two motor gearboxes. For use with Senior Swing. HEADERS HEADER, HL Standard, mounting header. Pair door, two operators. Specify length 52 to 98 maximum. END CAPS HEADER END CAPS, End cap with openings for wiring. ARMS CENTER PIVOT ARM, CP (CENTER PIVOT INSTALLATIONS ONLY) Used with overhead concealed operators and center pivoted doors HL 334 OFFSET PIVOT ARM, OP (OFFSET PIVOT OR BUTT HUNG INSTALLATIONS ONLY) Handed arm. Used with overhead concealed operators. OFFSET PIVOT ARM ASSEMBLY COMPLETE, OPCM Offset arm with track and concealing channel. Includes 3072 Concealing Channel, 168 Slide Channel and 30770P offset pivot arm. 3077CP 3077OP 30770PCM P 90

13 CHANNELS CONCEALING CHANNEL, Used to conceal arm in overhead concealed applications. For offset pivot and butt hinges installations only. If ordering separately specify length and hand. SLIDE CHANNEL, (OFFSET PIVOT or BUTT HINGE INSTALLATIONS ONLY) Mounts in top rail of door. Allows arm to slide. INSTALLATION ACCESSORIES STOP BREAKAWAY, B Allows in-swinging door to swing out in case of emergency. For center pivoted installations only. STOP FIXED, F Prevents out-swinging door from swinging in. For center pivoted installations only. FILLER PLATE BLANK, Completes length of header box. SPINDLE PLATE 2-3/4, A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2-3/4 center pivot hinge installations. SPINDLE PLATE 3-3/4, B Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 3-3/4 offset pivot, butt hinge or center pivot with finger guard installations. PIVOTS BOTTOM PIVOT ASSEMBLY, Includes pivot body, pivot post and bottom pivot plate. For overhead concealed, center pivoted installations. Includes; , and PIVOT BODY, Bottom pivot body for center pivoted installations. PIVOT POST, Connects pivot body to bottom pivot plate for center pivoted installations. BOTTOM PIVOT PLATE, Applied to floor for center pivoted installations SERIES B 384F 12 11A 11B ACCESSORIES 91

14 ORDERING INFORMATION 2850 SERIES TABLE OF SIZES COMBINED WIDTH 52" 1524mm 2853 Minimum Combined Door Width 96" 2438mm Indicates recommended range of door width for operator. NOTE: For all Senior Swing Series. Simultaneous Pair Width per leaf 26" minimum to 48 maximum. HOW-TO-ORDER 2850 SERIES S 1. SELECT INSTALLATION TYPE SPECIFY ARMS 3-3/4 (Offset pivoted) Arm (3077OP) 2-3/4 (Center pivoted) Arm (3077CP) 3-3/4 (Center pivoted) Arm (3077CP) 3. SPECIFY HAND (if double egress) RH LH 4. SPECIFY HEADER/LENGTHS HL (Specify length 52 to 98 ) 5. SPECIFY FINISH Standard Anodized Finish Aluminum or Dark Bronze. Operator will be shipped with: - STANDARD MOTOR GEARBOX (1 LH & 1 RH), - STANDARD CONTROL BOX, - COMPANION CABLE, - HEADER (at specified length - 72 standard), - 2-3/4 PIVOT POINT, - WOOD and MACHINE SCREW PACK Unless options listed below are selected. OPTIONS STOPS* Pair Positive Mechanical Stop (POS) Pair Panic Breakaway Stop (BKY) *Available with Center Pivoted installations only. 92

15 MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE 2860 SERIES The 2860 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Digital keypad for easy setup. n Meets International Building Code requirements and ANSI A n UL approved for fire doors. *CENTER PIVOT arm shown n 2860 Series operator is shipped with motor gearboxes, control boxes, bottom pivots, arms, header, and mounting hardware. Actuators available separately, see pages n Independent pair of doors, overhead concealed. n Meets ADA, requirements (power mode only). n Handed for double egress applications only. n 72 header length is standard. Specify other length 65 to 98 max. Consult factory regarding this option. n Optional fixed (POS) or breakaway stop (BKY) available (center pivot arm) - Header lengths 70 to 98 max with either (POS) or (BKY). n Adjustable hold open time of 1 to 32 seconds Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 2860 Series is UL listed for fire-rated applications. The 2860 Series also meets the provisions of the Americans with Disabilities Act. SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR MOUNTING HANDED* NON-HANDED SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE CONCEALED SIMULTANEOUS PAIR CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE LEVER) REGULAR (DOUBLE LEVER) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE * For double egress only. 93

16 2860 SERIES CONCEALED INDEPENDENT PAIR (CENTER PIVOT, EMERGENCY BREAKAWAY, PULL) MOUNTING Minimum header length 65 with applied stop by other and 70 with LCN Positive or Breakaway Stop. 1" 25 MM EMERGENCY BREAKAWAY 3 3/4 " 95 MM INCOMING EXTERIOR EMERGENCY BREAKAWAY 3 3/4 " 95 MM INCOMING 4 1/2 " 114 MM 5 3/4 " 146 MM 1" 25 MM DIRECTION 1/8" 3 MM BREAKAWAY STOP BREAKAWAY DIRECTION 8'-0" OPENING (MAX.) EXTERIOR CONCEALED INDEPENDENT PAIR (CENTER PIVOT, FIXED STOP, PUSH) MOUNTING Minimum header length 65 with applied stop by others and 70 with LCN Positive or Breakaway Stop. EXTERIOR 5 3/4 " 146 MM Shown w/ 3-3/4 pivot 4 1/2 " 114 MM 1/8" 3 MM OUTGOING OUTGOING 3 3/4 " 95 MM 3 3/4 " 95 MM FIXED STOP DIRECTION MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. 1" 25 MM 8'-0" OPENING (MAX.) 1" 25 MM EXTERIOR Shown w/ 3-3/4 pivot n Head Frame minimum 65 (L) x 5 3/4" (H) x 4 1/2" (W) (1651 mm x 146 mm x 114 mm). n Top Rail minimum 2 (51 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n Door Stop required for each door panel. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 94

17 2860 SERIES EXTERIOR 5 3/4" 146 MM 4 1/2" 114 MM CONCEALED INDEPENDENT PAIR (OFFSET PIVOT/BUTT HINGE, PUSH) MOUNTING Offset pivot installations require a bottom pivot and two intermediate pivots. OUTGOING OUTGOING SLIDE ARM ASS'Y OFFSET PIVOTS or BUTT HINGES 11" SLIDE CHANNEL SLIDE ARM ASS'Y WITH SLIDE BLOCK 1/8" 3 MM DIRECTION CONCEALING CHANNEL 10 1/2" 267 MM CONCEALING CHANNEL 3 3/4" 95 MM FRAME MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. n Head Frame minimum 65 (L) x 5-3/4 (H) x 4-1/2 (W) (1651 mm x 146 mm x 114 mm). n Top Rail minimum 2 (51 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n Door Stop required for each door panel. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 95

18 ACCESSORIES 2860 SERIES MOTOR GEARBOX MOTOR GEARBOX SENIOR, Driving mechanism for operator. Provides maximum of 15 lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET 3-3/4, Motor gearbox mounting bracket for 3-3/4 offset pivot, butt hinge or center pivot with finger guard installations. Front bracket. MOUNTING BRACKET 2-3/4, Motor gearbox mounting bracket for 2-3/4 center pivot installations. Front bracket. REAR MOUNT BRACKET, Motor gearbox mounting bracket. Rear bracket. CONTROL BOXES CONTROL BOX SENIOR, Electronic controlling device for Senior Swing. HEADERS HEADER, HL Standard, mounting header. Pair door, two operators. Specify length 65 to 98 maximum HL END CAPS HEADER END CAPS, End cap with openings for wiring. 334 ARMS CENTER PIVOT ARM, CP (CENTER PIVOT INSTALLATIONS ONLY) Used with overhead concealed operators and center pivoted doors. OFFSET PIVOT ARM, OP (OFFSET PIVOT OR BUTT HUNG INSTALLATIONS ONLY) Used with overhead concealed operators. OFFSET PIVOT ARM ASSEMBLY COMPLETE, OPCM Offset arm with track and concealing channel. Includes 3072 Concealing Channel, 168 Slide Channel and 30770P offset pivot arm. 3077CP 30770PCM 3077OP P 96

19 CHANNELS CONCEALING CHANNEL, Used to conceal arm in overhead concealed applications. For offset pivot and butt hinge installations only. If ordering separately specify length and hand. SLIDE CHANNEL, (OFFSET PIVOT or BUTT HINGE INSTALLATIONS ONLY) Mounts in top rail of door. Allows arm to slide. INSTALLATION ACCESSORIES STOP BREAKAWAY, B Allows in-swinging door to swing out in case of emergency. For center pivoted installations only. STOP FIXED, F Prevents out-swinging door from swinging in. For center pivoted installations only. FILLER PLATE BLANK, Completes length of header box. SPINDLE PLATE 2-3/4, A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2-3/4 center pivot hinge installations. SPINDLE PLATE 3-3/4, B Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 3-3/4 offset pivot/butt hinge or center pivot with finger guard installations. PIVOTS BOTTOM PIVOT ASSEMBLY, Includes pivot body, pivot post and bottom pivot plate. For overhead concealed, center pivoted installations. Includes; , and PIVOT BODY, Bottom pivot body for center pivoted installations. PIVOT POST, Connects pivot body to bottom pivot plate for center pivoted installations. BOTTOM PIVOT PLATE, Applied to floor for center pivoted installations SERIES B 384F 12 11A 11B 3107 ACCESSORIES

20 ORDERING INFORMATION 2860 SERIES TABLE OF SIZES WIDTH 65" 1651mm 2863 Minimum Door Width 96" 2438mm Indicates recommended range of door width for operator. NOTE: For all Senior Swing Series. Independent Pair Width per leaf 32-1/2 minimum to 48 maximum. HOW-TO-ORDER 2860 SERIES S 1. SELECT INSTALLATION TYPE SPECIFY ARMS Standard 3-3/4 (Offset pivoted) Arm (3077OP) Standard 2-3/4 (Center pivoted) Arm (3077CP) Standard 3-3/4 (Center pivoted) Arm (3077CP) 3. SPECIFY HAND (only for double egress) RH LH 4. SPECIFY HEADER/LENGTHS HL (Specify length 65 to 98 ) 5. SPECIFY FINISH Standard Anodized Finish Aluminum or Dark Bronze. Operator will be shipped with: - STANDARD MOTOR GEARBOX (1 LH & 1 RH), - STANDARD CONTROL BOX (2 ea), - HEADER (at specified length, 72 standard), - 2-3/4 PIVOT POINT, - WOOD and MACHINE SCREW PACK Unless options listed below are selected. OPTIONS STOPS* Pair Positive Mechanical Stop (POS) Pair Panic Breakaway Stop (BKY) *Available with Center Pivoted installations only. 98

21 SINGLE, SURFACE MOUNT (PULL) OFFSET PIVOT/BUTT HINGE 9530 SERIES The 9530 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Digital keypad for easy setup. n Meets International Building Code requirements and ANSI A n UL approved for fire doors. n 9530 Series operator is shipped with motor gearbox, control box, standard arm, header, and mounting hardware. Actuators available separately, see pages n Single door, surface mounted. n Meets ADA requirements (power mode only). n Handed product. n 36 header length is standard. Specify length 33 to 48 max. n Double door header available up to 98, specify other length 49 to 98 max. Consult factory regarding this option. n Adjustable hold open period of 2 to 32 seconds in automatic or manual mode Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 9530 Series is UL listed for fire-rated applications. The 9530 Series also meets the provisions of the Americans with Disabilities Act. SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE MOUNTING CONCEALED SIMULTANEOUS PAIR HANDED NON-HANDED CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE) REGULAR (DOUBLE) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE 99

22 9530 SERIES MOUNTING DETAILS TOP JAMB SINGLE (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PULL) MOUNTING NOTE: Cannot be used with swing clear hinges, pocket pivots or balanced doors. 48" OPENING (MAX.) 17 3/8 " 11 1/2 " PULL CHANEL 292 MM PULL ARM ASS'Y LEFT HAND INCOMING 2 3/4 " 70 MM OFFSET PIVOT or BUTT HINGES 1 3/4 " 44 MM 6 3/4 " 171 MM 1 15/16 " 49 MM 4 1/2 " 114 MM 5 3/4 " 146 MM 1 " 25 MM INTERIOR PULL ARM ASS'Y PULL CHANEL DIRECTION HOLLOW METAL FRAME Suggested Installation. MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. n Butt Hinges should not exceed 5 (127 mm) in width. n Reveal should not exceed 4 (102 mm). n Head Frame minimum 1-3/4 (44 mm). Face frame 6-3/4 (171 mm) total operator clearance. n Top Rail minimum 2-3/4 (70 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 100

23 MOTOR GEARBOX MOTOR GEARBOX SENIOR, Driving mechanism for operator. Provides maximum of 15 lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET 2-3/4, Motor gearbox mounting bracket for 2-3/4 offset pivot or butt hinge installations. Front bracket. REAR MOUNT BRACKET, Motor gearbox mounting bracket. Rear bracket. ANGLED BRACKET, Mounting bracket for surface applications. (Includes 2 mounting brackets) SERIES (2) 3462 ACCESSORIES CONTROL BOXES CONTROL BOX SENIOR, Electronic controlling device for Senior Swing. HEADERS HEADER, HL Standard, mounting header. Single door, single operator. Specify length 33 to 48 maximum. HEADER, DD Standard, mounting header. Double door, single operator. Specify length 49 to 98 maximum. 3572HL 3572DD END CAPS HEADER END CAPS, End cap with openings for wiring. END DRESS PLATE, Metal finish end cap

24 9530 SERIES ACCESSORIES ARMS STANDARD ARM ASSEMBLY, PLCM Handed arm. Track roller included. (Includes 3038, 3077T, 3034 & 73). STANDARD ARM, T Handed arm. Track roller not included. 3077PLCM 3077T T TRACKS TRACK Standard non-handed track. (Includes 3034 & 73). TRACK END CAP Black plastic end caps. ROLLER, Quiet low friction roller assembly. INSTALLATION ACCESSORIES SPINDLE PLATE 2-3/4, A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2-3/4 offset pivot or butt hinge installations A 73 FILLER PLATE BLANK, Completes length of header box. (Specify Length). 12 MOUNTING PLATE, Optional mounting plate for standard hollow metal door frames. Specify length 36-1/2 to 101-1/2 maximum, when angle brackets. Specify length 33 to 98 maximum when using end dress plates. NOTE: The length of a universal 18 plate will need to be ordered 3-1/2 longer than the supplied header when using angle brackets

25 9530 SERIES TABLE OF SIZES WIDTH 33" 838mm 9531 Minimum Door Width 48" 1219mm Indicates recommended range of door width for operator. NOTE: For all Senior Swing Series. Single Door - Width per leaf 33 minimum, 48 maximum. HOW-TO-ORDER 9530 SERIES S 1. SPECIFY HAND RH LH 2. SPECIFY HEADER/LENGTH HL (Specify length 33 to 48 ) DD (Specify length 49 to 98 ) 3. SPECIFY FINISH Standard Anodized Finish Aluminum or Dark Bronze. Operator will be shipped with: - STANDARD MOTOR GEARBOX, - STANDARD CONTROL BOX, - HEADER (at specified Length, 36 standard), - STANDARD ARM (3077T), - 2-3/4 PIVOT POINT, - STANDARD TRACK w/track ROLLER, - MACHINE SCREW PACK Unless options listed below are selected. ORDERING INFORMATION OPTIONS MOUNTING PLATE Plate, (Specify Length 33 to 101-1/2 ) 103

26 Notes 104

27 SINGLE, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9540 SERIES The 9540 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Digital keypad for easy setup. n Meets International Building Code requirements and ANSI A n UL approved for fire doors. n 9540 Series operator is shipped with motor gearbox, control box, regular arm, header, and mounting hardware. Actuators available separately, see pages n Single door, surface mounted. n Meets ADA requirements (power mode only). n Handed product. n 36 header length is standard. Specify length 33 to 48 max. n Double door header available up to 98, specify other length 49 to 98 max. Consult factory regarding this option. n Adjustable hold open period of 2 to 32 seconds in automatic or manual mode Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 9540 Series is UL listed for fire-rated applications. The 9540 Series also meets the provisions of the Americans with Disabilities Act. MOUNTING HANDED NON-HANDED SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE CONCEALED SIMULTANEOUS PAIR CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE LEVER) REGULAR (DOUBLE LEVER) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE 105

28 9540 SERIES MOUNTING DETAILS TOP JAMB SINGLE (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTING Consult factory for all balance door installations. HOLLOW METAL FRAME Suggested Installation. OFFSET PIVOT or BUTT HINGES OUTGOING PUSH ARM ASS'Y 17" From edge of door 2 3/4 " 70 MM 48" OPENING (MAX.) REVEAL 6 3/4 " 171 MM 1 " 25 MM 4 1/2 " 114 MM 5 3/4 " 146 MM SECONDARY LINK FRAME 1 7/16 " From top of door DIRECTION EXTERIOR MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. n Butt Hinges should not exceed 5 (127 mm) in width. n Reveal for push installations should not exceed 10 (254 mm) for REGULAR ARM and 20 (508 mm) for LONG ARM. n Head Frame minimum 1-3/4 (44 mm). Face frame 6-3/4 (171 mm) total operator clearance. n Top Rail minimum 2-3/4 (70 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 106

29 MOTOR GEARBOX MOTOR GEARBOX SENIOR, Driving mechanism for operator. Provides 15 lbs opening force. Handed. MOUNTING BRACKET MOUNTING BRACKET 2-3/4, Motor gearbox mounting bracket for 2-3/4 offset pivot or butt hinge installations. Front bracket. REAR MOUNT BRACKET, Motor gearbox mounting bracket. Rear bracket. ANGLED BRACKET, Mounting bracket for surface applications. (Includes 2 mounting brackets). CONTROL BOXES CONTROL BOX SENIOR, Electronic controlling device for Senior Swing SERIES (2) 3462 ACCESSORIES HEADERS Header, HL Standard, mounting header. Single door, single operator. Specify length 33 to 48 maximum. Header, DD Standard, mounting header. Double door, single operator. Specify length 49 to 98 maximum. 3572HL 3572DD END CAPS HEADER END CAPS, End cap with openings for wiring. END DRESS PLATE, Metal finish end cap

30 ACCESSORIES 9540 SERIES ARMS REGULAR ARM ASSEMBLY, Handed arm. REGULAR LONG ARM ASSEMBLY, L Handed arm L MAIN ARM, Handed arm attaches to motor gearbox. 77 LINKAGE ASSEMBLY 15, Threaded rod attaches to door. Extends from main arm. LINKAGE ASSEMBLY 32, LR Threaded long rod attaches to door. Extends from main arm. Used for reveal 10 to 20. INSTALLATION ACCESSORIES SPINDLE PLATE 2-3/4, A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2-3/4 offset pivot or butt hinge installations LR 11A FILLER PLATE BLANK, Completes length of header box. (Specify length). 12 MOUNTING PLATE, Optional mounting plate for standard hollow metal door frames. Specify length 36-1/2 to 101-1/2 maximum, when angle brackets. Specify length 33 to 98 maximum when using end dress plates. 18 NOTE: The length of a universal 18 plate will need to be ordered 3-1/2 longer than the supplied header when using angle brackets. 108

31 9540 SERIES TABLE OF SIZES WIDTH 33" 838mm 9542 Minimum Door Width 48" 1219mm Indicates recommended range of door width for operator. NOTE: For all Senior Swing Series. Single Door - Width per leaf 33 minimum, 48 maximum. HOW-TO-ORDER 9540 SERIES S 1. SPECIFY HAND RH LH 2. SPECIFY HEADER/LENGTH HL (Specify length 33 to 48 ) DD (Specify length 49 to 98 ) 3. SPECIFY FINISH Standard Anodized Finish Aluminum or Dark Bronze. Operator will be shipped with: - STANDARD MOTOR GEARBOX, - STANDARD CONTROL BOX, - HEADER (at specified length, 36 standard), - REGULAR ARM (3077), - 2-3/4 PIVOT POINT, - WOOD and MACHINE SCREW PACK Unless options listed below are selected. ORDERING INFORMATION OPTIONS MOUNTING PLATE Plate, (Specify Length 33 to 101-1/2 ) ARM Long Arm (3077L) 109

32 Notes 110

33 MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS 9550 SERIES The 9550 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES n 9550 Series operator is shipped with motor gearboxes, control box, arms, header, and mounting hardware. Actuators available separately, see pages n Simultaneous pair, surface mounted. n Meets ADA requirements (power mode only). n Handed product. *PULL SIDE mount shown n Pull, Push or Double Egress applications available. n 72 header length is standard. Specify other length 52 to 98. Consult factory regarding this option. n Adjustable hold open period of 2 to 32 seconds in automatic or manual mode. n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Digital keypad for easy setup. n Meets International Building Code requirements and ANSI A n UL approved for fire doors Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 9550 Series is UL listed for fire-rated applications. The 9550 Series also meets the provisions of the Americans with Disabilities Act. SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR MOUNTING HANDED NON-HANDED SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE CONCEALED SIMULTANEOUS PAIR CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE LEVER) REGULAR (DOUBLE LEVER) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE 111

34 LCN 9550 SERIES MOUNTING DETAILS TOP JAMB SIMULTANEOUS PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTING Consult factory for all balanced door installations. OUTGOING PUSH ARM ASS'Y 17" From edge of door REVEAL 8'-0" OPENING (MAX.) OUTGOING 4 1/2 " 114 MM 6 3/4 " 5 3/4 " 171 MM 146 MM OFFSET 1 " PIVOT 25 MM or BUTT HINGES SECONDARY LINK 2 3/4 " 70 MM FRAME 1 7/16 " From top of door DIRECTION EXTERIOR TOP JAMB SIMULTANEOUS PAIR (OFFSET PIVOT/ BUTT HINGE, CENTER PIVOT, PULL) MOUNTING NOTE: Cannot be used with swing clear hinges, pocket pivots or balanced doors. 4 1/2 " 114 MM 8'-0" OPENING (MAX.) 17 3/8 " 11 1/2 " 5 3/4 " 441 MM 291 MM 6 3/4 " 146 MM 2 3/4 " 171 MM 70 MM PULL CHANNEL OFFSET PIVOT 1 " PULL ARM or ASS'Y BUTT 1 15/16 " 25 MM HINGES 49 MM PULL ARM ASS'Y PULL CHANNEL INCOMING INTERIOR INCOMING DIRECTION 1 3/4 " 44 MM INTERIOR MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. Contact LCN Product Support for installation assistance. n Butt Hinges should not exceed 5 (127 mm) in width. n Reveal for push installations should not exceed 10 (254 mm) for REGULAR ARM and 20 (508 mm) for LONG ARM. n Reveal for pull installations should not exceed 4 (102 mm). n Reveal for double egress installations should not exceed 4 (102 mm). n Head Frame minimum 1-3/4 (44 mm). Face frame 6-3/4 (171 mm) total operator clearance. n Top Rail minimum 2-3/4 (70 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. 112

35 9550 SERIES 2 3/4 " 70 MM BUTT HINGES 48" OPENING (MAX.) 17" From edge of door PUSH ARM ASS'Y PULL ARM ASS'Y 17 3/8 " 11 1/2 " PULL CHANNEL 292 MM 48" OPENING (MAX.) 1 3/4 " 44 MM BUTT HINGES 2 3/4 " 70 MM 5 3/4 " 146 MM 1 " 25 MM 4 1/2 " 114 MM PUSH ARM ASS'Y SECONDARY LINK FRAME 2 3/18" FROM BOTTOM OF STOP 6 3/4 " 171 MM 5 3/4 " 146 MM 4 1/2 " 114 MM 1 " 25 MM PULL ARM ASS'Y PULL CHANNEL DIRECTION FRAME DIRECTION INTERIOR 1 15/16" FROM TOP OF TOP JAMB SIMULTANEOUS PAIR (RH DOUBLE EGRESS) MOUNTING Double egress applications with safety sensors require LCN 9560 series. NOTE: Cannot be used with swing clear hinges, pocket pivots or balanced door. HOLLOW METAL FRAME Suggested Installation. MOUNTING DETAILS MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. n Butt Hinges should not exceed 5 (127 mm) in width. n Reveal for push installations should not exceed 10 (254 mm) for REGULAR ARM and 20 (508 mm) for LONG ARM. n Reveal for pull installations should not exceed 4 (102 mm). n Reveal for double egress installations should not exceed 4 (102 mm). n Head Frame minimum 1-3/4 (44 mm). Face frame 6-3/4 (171 mm) total operator clearance. n Top Rail minimum 2-3/4 (70 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for installation assistance. 113

36 ACCESSORIES 9550 SERIES MOTOR GEARBOX MOTOR GEARBOX SENIOR, Driving mechanism for operator. Provides 15 lbs opening force. Handed. MOUNTING BRACKETS MOUNTING BRACKET 2-3/4, Motor gearbox mounting bracket for 2-3/4 offset pivot or butt hinge installations. Front bracket. REAR MOUNT BRACKET, Motor gearbox mounting bracket. Rear bracket. ANGLED BRACKET, Mounting bracket for surface applications. (Includes 2 mounting brackets) (2) 3462 CONTROL BOXES CONTROL BOX SENIOR, Electronic controlling device for Senior Swing. COMPANION CABLE, Cable that allows one control box to run two motor gear boxes. Companion cable. For use with Senior Swing. HEADERS HEADER, HL Standard, mounting header. Pair door, two operators. Specify length 52 to 98 maximum HL END CAPS HEADER ENDCAPS, End cap with openings for wiring. END DRESS PLATE, Metal finish end cap

37 ARMS STANDARD ARM ASSEMBLY, PLCM Handed arm. (Includes 3077 regular arm assembly, 3038 track, and 3034 track roller). REGULAR ARM ASSEMBLY, Handed arm. (Includes 77 main arm assembly and 79 linkage assembly). REGULAR LONG ARM ASSEMBLY, L Handed arm. (Includes 77 main arm assembly and 79LR linkage assembly). STANDARD ARM, T Handed arm. Track roller not included. MAIN ARM, Handed arm attaches to motor gearbox. LINKAGE ASSEMBLY 15, Threaded rod attaches to door. Extends from main arm. LINKAGE ASSEMBLY 32, LR Threaded long rod attaches to door. Extends from main arm. Used for reveal 10 to 20. TRACKS TRACK Standard non-handed track. TRACK END CAP Black plastic end caps. ROLLER, Quiet low friction roller assembly. INSTALLATION ACCESSORIES SPINDLE PLATE 2-3/4, A Hides bottom of motor gearbox. Completes header box. Cutout allows for motor gearbox shaft. For 2-3/4 offset pivot or butt hinge installations. FILLER PLATE BLANK, Completes length of header box. (Specify length). MOUNTING PLATE, Optional mounting plate for standard hollow metal door frames. Specify length 55-1/2 to 101-1/2 maximum when using angle brackets. Specify length 52 to 98 maximum when using dress plates. NOTE: The length of a universal 18 plate will need to be ordered 3-1/2 longer than the supplied header when using angle brackets. 3077PLCM L T LR A SERIES 73 79/ 79LR 3034 ACCESSORIES 115

38 ORDERING INFORMATION 9550 SERIES TABLE OF SIZES COMBINED WIDTH 52" 1321mm 9553 Minimum Combined Door Width 96" 2438mm Indicates recommended range of door width for operator. NOTE: For all Senior Swing Series. Simultaneous Pair Width per leaf 30 minimum to 48 maximum. HOW-TO-ORDER 9550 SERIES S 1. SPECIFY HAND RH LH 2. SPECIFY HEADER / LENGTH HL (Specify length 52 to 98 ) regular or long arm HL (Specify length 60 to 98 ) for standard or DE arm 3. SPECIFY FINISH Standard Anodized Finish Aluminum or Dark Bronze. Operator will be shipped with: - STANDARD MOTOR GEARBOX (SF) (2 ea), - STANDARD CONTROL BOX (SC), - METAL COVER (at specified length 72 standard), - REGULAR ARM (2 ea), - 2-3/4 PIVOT POINT, - MACHINE SCREW PACK OPTIONS MOUNTING PLATE Plate, (Specify Length 52 to 101-1/2 ) ARM Standard Arm (2 ea) w/standard Track (2 ea) Double Egress Includes Standard Arm w/track (1 ea) & Regular Arm (1 ea) Long Arm (3077L) 116

39 MOUNTS INDEPENDENT PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS 9560 SERIES The 9560 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated, opens doors automatically for wheelchair access, yet allows for manual operation for regular pedestrian traffic. FEATURES *PULL SIDE mount shown n 9560 Series operator is shipped with motor gearboxes, control boxes, arms, header, and mounting hardware. Actuators available separately, see pages n Independent pair, surface mounted. n Meets ADA requirements (power mode only). n Handed product. n Pull, Push or Double Egress applications available. n 72 header length is standard. Specify other length 65 to 98. Consult factory regarding this option. n Adjustable hold open period of 2 to 32 seconds in automatic or manual mode. n Push N Go permits non-switch activation. n Power Boost provides additional latching force. n Electromechanical unit with microprocessor control. n Digital keypad for easy setup. n Meets International Building Code requirements and ANSI A n UL approved for fire doors Series is fully compliant with UL 325 & UL 1998 and meets the provisions of ANSI A The 9560 Series is UL listed for fire-rated applications. The 9560 Series also meets the provisions of the Americans with Disabilities Act. SURFACE MOUNT SINGLE SURFACE MOUNT SIMULTANEOUS PAIR MOUNTING HANDED NON-HANDED SURFACE MOUNT INDEPENDENT PAIR CONCEALED SINGLE CONCEALED SIMULTANEOUS PAIR CONCEALED INDEPENDENT PAIR HANDING STANDARD ANODIZED METAL FINISH COVER STANDARD (SINGLE LEVER) REGULAR (DOUBLE LEVER) DOUBLE EGRESS (PUSH/PULL) ARM FUNCTION OFFSET PIVOT BUTT HINGE ARM CENTER PIVOT ARM AVAILABLE NOT AVAILABLE 117

40 9560 SERIES MOUNTING DETAILS TOP JAMB INDEPENDENT PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PUSH) MOUNTING Consult factory for all balanced door installations. OUTGOING PUSH ARM ASS'Y 17" From edge of door REVEAL 8'-0" OPENING (MAX.) OUTGOING 4 1/2 " 114 MM 6 3/4 " 5 3/4 " 171 MM 146 MM OFFSET 1 " PIVOT 25 MM or BUTT HINGES SECONDARY LINK 2 3/4 " 70 MM FRAME 1 7/16 " From top of door DIRECTION EXTERIOR TOP JAMB INDEPENDENT PAIR (OFFSET PIVOT/BUTT HINGE, CENTER PIVOT, PULL) MOUNTING NOTE: Cannot be used with swing clear hinges, pocket pivots or balanced doors. 4 1/2 " 114 MM 8'-0" OPENING (MAX.) 17 3/8 " 11 1/2 " 5 3/4 " 441 MM 291 MM 6 3/4 " 146 MM 2 3/4 " 171 MM 70 MM PULL CHANNEL OFFSET PIVOT 1 " PULL ARM or ASS'Y BUTT 1 15/16 " 25 MM HINGES 49 MM PULL ARM ASS'Y PULL CHANNEL INCOMING INTERIOR INCOMING DIRECTION 1 3/4 " 44 MM INTERIOR MAXIMUM OPENING Template allows 90 degree power opening and 90 degree manual opening. n Butt Hinges should not exceed 5 (127 mm) in width. n Reveal for push installations should not exceed 10 (254 mm) for REGULAR ARM and 20 (508 mm) for LONG ARM. n Reveal for pull installations should not exceed 4 (102 mm). n Reveal for double egress installations should not exceed 4 (102 mm). n Head Frame minimum 1-3/4 (44 mm). Face frame 6-3/4 (171 mm) total operator clearance. n Top Rail minimum 2-3/4 (70 mm). n Opening & Closing Time are variable by adjustments to the electronic control box. Maximum hold open time adjustable up to approximately 32 seconds. n System Diagram see AUTOMATIC S section pages 53 for typical system wiring and page 56 for electrical data. Contact LCN Product Support for assistance. 118

9550 SERIES FEATURES OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS

9550 SERIES FEATURES OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS 9550 SERIES The 9550 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operators when activated,

More information

2860 SERIES FEATURES OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE

2860 SERIES FEATURES OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE The 2860 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when

More information

9540 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE

9540 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9540 SERIES The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated,

More information

*PULL SIDE mount shown

*PULL SIDE mount shown MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS The 9550 SENIOR by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR operators when activated, opens

More information

LCN 2810 SERIES OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED CENTER PIVOT ARM OFFSET PIVOT/BUTT HINGE

LCN 2810 SERIES OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED CENTER PIVOT ARM OFFSET PIVOT/BUTT HINGE OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE The 2810 SENIOR by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR operator when activated,

More information

*CENTER PIVOT arm shown

*CENTER PIVOT arm shown OPERATOR MOUNTS INDEPENDENT PAIR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE *CENTER PIVOT arm shown 2860 series operator is shipped with motor gearbox, control boxes, bottom pivots, arms,

More information

9550 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting

9550 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting Senior Features The 9550 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet

More information

9560 Series Senior Swing. Features. Special Templates. Cover Fasteners Mounting. Certifications

9560 Series Senior Swing. Features. Special Templates. Cover Fasteners Mounting. Certifications Senior Features The 9560 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet

More information

LCN 9540 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE

LCN 9540 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE The 9540 SENIOR SWING by LCN is an ADA door operator that is a two-inone swing door operator. SENIOR SWING operators when activated, opens doors

More information

*CENTER PIVOT arm shown

*CENTER PIVOT arm shown OPERATOR MOUNTS SINGLE DOOR, OVERHEAD CONCEALED *CENTER PIVOT OFFSET PIVOT/BUTT HINGE *CENTER PIVOT arm shown 2910 series operator is shipped with motor gearbox, control box, arm, bottom pivot, header,

More information

LCN 9740 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE

LCN 9740 SERIES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9740 series operator is shipped with motor gearbox, control box, regular arm, header, and mounting hardware. Actuators available separately, see

More information

2850 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting

2850 Series Senior Swing. Features. Special Templates. Certifications. Fasteners Mounting Features The 2850 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operator when activated, opens doors automatically for wheelchair access, yet allows

More information

9530 Series Senior Swing. Features. Special Templates. Fasteners Mounting. Certifications

9530 Series Senior Swing. Features. Special Templates. Fasteners Mounting. Certifications Features The 9530 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators when activated, opens doors automatically for wheelchair access, yet allows

More information

LCN AUTOMATIC OPERATORS

LCN AUTOMATIC OPERATORS LCN AUTOMATIC OPERATORS SENIOR 9530 SENIOR 9540 SENIOR 9550 SENIOR 9560 8310 ACCESSORIES LCN ELECTROMECHANICAL POWERED SYSTEMS ELECTROMECHANICAL AUTOMATIC OPERATORS LCN s electromechanical products are

More information

9550 SERIES FEATURES OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS

9550 SERIES FEATURES OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS OPERATOR MOUNTS SIMULTANEOUS PAIR, SURFACE MOUNT *PULL SIDE PUSH SIDE DOUBLE EGRESS The 9550 SENIOR SWING by LCN is an ADA door operator that is a two-in-one swing door operator. SENIOR SWING operators

More information

9140 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE

9140 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE SINGLE, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE 9140 SERIES The 9140 BENCHMARK by LCN is an electrically powered low-energy operator. It provides easy access for people with disabilities, or the elderly.

More information

LCN 9140 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE

LCN 9140 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE SINGLE, SURFACE MOUNT (PUSH) OFFSET PIVOT/BUTT HINGE The 9140 BENCHMARK by LCN is an electrically powered low-energy operator. It provides easy access for people with disabilities, the elderly or the frail.

More information

LCN 9130 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PULL) OFFSET PIVOT/BUTT HINGE

LCN 9130 SERIES FEATURES SINGLE DOOR, SURFACE MOUNT (PULL) OFFSET PIVOT/BUTT HINGE SINGLE, SURFACE MOUNT (PULL) OFFSET PIVOT/BUTT HINGE The 9130 BENCHMARK by LCN is an electrically powered low-energy operator. It provides easy access for people with disabilities, the elderly or the frail.

More information

Electrohydraulic Powered Systems

Electrohydraulic Powered Systems Electrohydraulic Powered Systems ELECTRIC AUTO EQUALIZERS These Auto Equalizer products are an addition to the original pneumatic drive system. People moving through a door can use it as a normal rack

More information

4640 shown POWER OPERATOR HOLD-OPEN ACCESSIBILITY* NON-HANDED NON-SIZED

4640 shown POWER OPERATOR HOLD-OPEN ACCESSIBILITY* NON-HANDED NON-SIZED TOP JAMB (PUSH SIDE) MOUNTING The 4640 AUTO EQUALIZER is LCN s SMART & RELIABLE electrically powered low-energy power operator. It provides easy access for people with disabilities, or the elderly. Designed

More information

CONCEALED CLOSER SERIES

CONCEALED CLOSER SERIES CLOSER SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of

More information

DOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM

DOUBLE LEVER ARM DOUBLE LEVER ARM SINGLE LEVER ARM 5010 SINGLE LEVER ARM SERIES PRODUCT SELECTION GUIDE The concealed LCN closers feature a modern design for concealment in either the head frame or top rail of the door. This guide is based on the desired mounting of the closer.

More information

LCN 4310ME SERIES FEATURES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled

LCN 4310ME SERIES FEATURES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for FEATURES fire and smoke barrier doors. Door

More information

CONCEALED CLOSER SERIES

CONCEALED CLOSER SERIES CONCEALED CLOSER SERIES APPLICATIONS n For aluminum, hollow metal, or wood doors and frames. n Can be used with hinge or pivot mounted door. n Closers for 4 or minimum 1-3/4 head frame or 4 top rail. n

More information

NON-SIZED SIZED HANDED

NON-SIZED SIZED HANDED HINGE (PULL) SIDE MOUNTING 4310ME SERIES The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.

More information

LCN 4310ME SERIES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled. closer/holder designed to provide

LCN 4310ME SERIES HINGE (PULL) SIDE MOUNTING. The 4310ME SENTRONIC is a. heavy duty, electrically controlled. closer/holder designed to provide HINGE (PULL) SIDE MOUNTING The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide FEATURES infinitely adjustable hold-open for fire and smoke barrier doors. Door

More information

SURFACE MOUNTED PULL SIDE

SURFACE MOUNTED PULL SIDE AUTOMATIC OPERATORS PRODUCT SELECTION GUIDE LCN automatic operators are the proven standard in schools and health care facilities for over 20 years. They are easily retrofitted into existing doors and

More information

4310ME Series. Features E25. Special Templates. Grade 1 - ANSI A156.15, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act, NFPA 101

4310ME Series. Features E25. Special Templates. Grade 1 - ANSI A156.15, UL 10C, ADA, 100 Hour Salt Spray, Meets BAA - Buy American Act, NFPA 101 Features The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until current

More information

Senior Swing Control Box. Table of Contents

Senior Swing Control Box. Table of Contents *740100* 740100 2800 Overhead Consealed Series 9500 Surface Applied Series Senior Swing Control Box Installation Instructions important These instructions are presented in step-by-step sequence. It is

More information

LCN 4010T SERIES HINGE (PULL) SIDE

LCN 4010T SERIES HINGE (PULL) SIDE HINGE (PULL) SIDE MOUNT The 4010T SMOOTHEE is LCN s best performing heavy duty track closer designed specifically for interior doors in institutional and other rugged high traffic applications. FEATURES

More information

FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES

FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES FIRE/LIFE SAFETY CLOSERS/HOLDERS SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke

More information

4840 with EDA arm and 459 Door Loop

4840 with EDA arm and 459 Door Loop PARALLEL ARM (PUSH SIDE) MOUNTING The 4840 AUTO EQUALIZER is LCN s pneumatically powered MULTI- DOOR solution. This low-energy automatic operator provides easy access for people with disabilities, or the

More information

4310ME Series. Features E25. Special Templates. Certifications. Cover Fasteners Mounting Arms

4310ME Series. Features E25. Special Templates. Certifications. Cover Fasteners Mounting Arms 4310ME Features The 4310ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until

More information

High Security Closers Series

High Security Closers Series High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can

More information

FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE

FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE FIRE/LIFE SAFETY SERIES PRODUCT SELECTION GUIDE SENTRONIC Series LCN closer/holders combine heavy duty closers with electrically controlled hold-open functions to control fire and smoke barrier doors.

More information

KEANE MONROE a member of the record group

KEANE MONROE a member of the record group SERIES 3000 / 3100 MICROPROCESSOR CONTROL REGULAR ARM SLIDE ARM / SLIDE ARM W/PANIC BREAKAWAY SERIES 3000 / 3100 Page 1. INDEX and OPERATOR HANDING The KM Series 3000/3100 operators have been carefully

More information

4000 Series mounted closers

4000 Series mounted closers 4000 mounted closers APPLICATIONS n For aluminum, hollow metal, or wood swinging doors and frames. n Can be used with hinge or pivot mounted door. n Adapter plates and other installation accessories available

More information

4040XPT Series Door controls

4040XPT Series Door controls 4040XPT Series Door controls Fire Rated: Tested on fire door assemblies in accordance with Australian Standards, refer fire door manufacturer for specific approval details The LCN 4040XPT Series is a non-handed,

More information

Concealed overhead closer for high-end applications DOOR CLOSERS CATALOG

Concealed overhead closer for high-end applications DOOR CLOSERS CATALOG Concealed overhead closer for high-end applications 7900 S E R I E S DOOR CLOSERS CATALOG INTRODUCTION The 7900 Series Overhead Concealed Closers offer extremely durable operation with the vandal resistance

More information

Dor-O-Matic. Senior-Swing Universal Control Box. Instruction Manual Universal Control Box DOR-O-MATIC

Dor-O-Matic. Senior-Swing Universal Control Box. Instruction Manual Universal Control Box DOR-O-MATIC Dor-O-Matic Senior-Swing Universal Control Box Instruction Manual 85445-900 Universal Control Box Factory Authorized Door Leaf Size & Weight: Type Width per Leaf Max. Weight per Leaf Single Door 36" to

More information

*HINGE (pull) side mount shown

*HINGE (pull) side mount shown CLOSER MOUNTS *HINGE (PULL) SIDE TOP JAMB (PULL SIDE) STOP FACE (PUSH SIDE) The 4040T SMOOTHEE is LCN s most flexible heavy duty track closer designed specifically for interior doors in institutional and

More information

NON-SIZED SIZED HANDED

NON-SIZED SIZED HANDED 4040SE SERIES n Standard 4040SE Series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks are optional,

More information

Electro-Mechanical Swing Operator. Table of Contents

Electro-Mechanical Swing Operator. Table of Contents *640072* 640072 Electro-Mechanical Swing Operator Models 8230 & 8240 Installation Instructions Table of Contents General...1 Replacement Parts & System Components...1 1 Pre-Installation Site & Product

More information

HIGH SECURITY SERIES

HIGH SECURITY SERIES HIGH SECURITY SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide is based

More information

PUSH SIDE M O U N T E D PULL SIDE M O U N T E D D O U B L E LEVER ARM LEVER ARM P D O U B L E LEVER ARM S I N G L E LEVER ARM

PUSH SIDE M O U N T E D PULL SIDE M O U N T E D D O U B L E LEVER ARM LEVER ARM P D O U B L E LEVER ARM S I N G L E LEVER ARM 4000 SERIES PRODUCT SELECTION GUIDE Surface mounted 4000 Series LCN closers feature a modern design engineered for each application, easy installation, and superior performance. This guide is based on

More information

LCN 4040SE SERIES FEATURES HINGE (PULL) SIDE MOUNTING

LCN 4040SE SERIES FEATURES HINGE (PULL) SIDE MOUNTING HINGE (PULL) SIDE MOUNTING Standard 4040SE series closer shipped with a standard arm, 24V or 120V (please specify) SE track, standard plastic clip-on cover, and wood and machine screw pack. SEL tracks

More information

HIGH SECURITY CLOSERS SERIES

HIGH SECURITY CLOSERS SERIES HIGH SECURITY CLOSERS SERIES PRODUCT SELECTION GUIDE High Security LCN closers feature a vandal resistant design engineered for each application, easy installation, and superior performance. This guide

More information

7100SZ SERIES. Multi-Point Closer/Holder with Motion Sensor

7100SZ SERIES. Multi-Point Closer/Holder with Motion Sensor safezone Multi-Point Closer/Holder with Motion Sensor introduction Designed with safety in mind, SafeZone takes door closers to a higher level. SafeZone uses a multi-point, electromechanical closer and

More information

Power Operators. Requirement. Approved Manufacturers. -All Operators To Be Electrically Powered -Operators To Be Aluminum (BHMA 689) Finish

Power Operators. Requirement. Approved Manufacturers. -All Operators To Be Electrically Powered -Operators To Be Aluminum (BHMA 689) Finish Power Operators Requirement -All Operators To Be Electrically Powered -Operators To Be Aluminum (BHMA 689) Finish Approved Manufacturers -Besam No Substitution 9 SW200i Technical Data Sheet ASSA ABLOY,

More information

AUTOMATIC OPERATORS SURFACE MOUNTED PULL SIDE

AUTOMATIC OPERATORS SURFACE MOUNTED PULL SIDE AUTOMATIC OPERATORS PRODUCT SELECTION GUIDE LCN automatic operators are the proven standard in schools and health care facilities for over 20 years. They are easily retrofitted into existing doors and

More information

AL(689) DKBRZ(695) DKBRZ(695) LTZPC(691) AL(689) DKBRZ(695) AL(689) DKBRZ(695)

AL(689) DKBRZ(695) DKBRZ(695) LTZPC(691) AL(689) DKBRZ(695) AL(689) DKBRZ(695) Cast Aluminum Closers 1250 SERIES packed w/tbms (Thru Bolts, Wood & Machine Screws) 1250 Regular w/pa 185.00 1250H Hold Open w/pa 215.00 Commercial Closers 1260 SERIES BRASS(696) packed w/tbwms (Thru Bolts,

More information

High Security Closers Series

High Security Closers Series High Security Closers APPLICATIONS n For any concealed or surface mounted installation subject to potential abuse or vandalism. n For correctional, aluminum, hollow metal, or wood doors and frames. n Can

More information

Door Closer Cycle. How to Select the Proper Closer. Things to Consider

Door Closer Cycle. How to Select the Proper Closer. Things to Consider Door Control Closer Spring Adjustment Not Shown in Door Closer Cycle Diagram Effects the entire cycle of the door closer movement Used to size closer for application requirements Determines the amount

More information

PULL SIDE MOUNTED PUSH SIDE MOUNTED DOUBLE LEVER ARM LEVER ARM P DOUBLE LEVER ARM SINGLE LEVER ARM 4110T 4210T*

PULL SIDE MOUNTED PUSH SIDE MOUNTED DOUBLE LEVER ARM LEVER ARM P DOUBLE LEVER ARM SINGLE LEVER ARM 4110T 4210T* 4000 SERIES PRODUCT SELECTION GUIDE Surface mounted 4000 Series LCN closers feature a modern design engineered for each application, easy installation, and superior performance. This guide is based on

More information

MOUNTING FINISH COVER CYLINDER **ARM FUNCTION REGULAR (DOUBLE) DESIGNER METAL NON-HANDED NON-SIZED

MOUNTING FINISH COVER CYLINDER **ARM FUNCTION REGULAR (DOUBLE) DESIGNER METAL NON-HANDED NON-SIZED HINGE (PULL) SIDE MOUNT LCN 4010 SERIES The 4010 SMOOTHEE is LCN s best performing heavy duty closer designed specifically for institutional and other rugged high traffic applications. FEATURES Ten Million

More information

Headline. Overhead Door Holders/Stops

Headline. Overhead Door Holders/Stops Headline Overhead Door Holders/Stops Quality hardware for superior door control 2 Glynn-Johnson has been providing the highest quality door control hardware for 75 years. Known in the industry as the overhead

More information

LCN Super Smoothie Adjustable Closer Super Smoothie Adjustable Closer

LCN Super Smoothie Adjustable Closer Super Smoothie Adjustable Closer 4041 Super Smoothie Adjustable Closer Parallel Arm Mount Shown 4041 Super Smoothie Adjustable Closer The 4041 SUPER SMOOTHIE is a heavy duty, double lever arm closer for institutional and other high traffic

More information

Copyright , 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express

Copyright , 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express over he ad conce aled closer s o v e r h e a d c o n c e a l e d c l o s e r s i n t r o d u c t i o n i n t r o d u c t i o n Rixson Overhead Concealed closers offer an aesthetically appealing way to

More information

Metal, Standard Wood and machine screw pack Top jamb (Push Side) Body Construction. Finishes/Colors/ Powder Coat. Wiring NON-SIZED SIZED

Metal, Standard Wood and machine screw pack Top jamb (Push Side) Body Construction. Finishes/Colors/ Powder Coat. Wiring NON-SIZED SIZED Features The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors. Door is held open until current

More information

5200 Series

5200 Series 5200 Series 5200 Series Closers are engineered and designed to offer the ideal combination of appearance and reliability. The 5200 Series Closers are constructed of aluminum alloy to be installed on exterior

More information

Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG

Full-featured operator with slim profile for moderate to high traffic applications LOW ENERGY OPERATOR CATALOG Full-featured operator with slim profile for moderate to high traffic applications 6300 S E R I E S LOW ENERGY OPERATOR CATALOG INTRODUCTION The Norton 6300 Series Low Energy Operator offers a broad set

More information

Allegion LCN Benchmark AU9100 Series

Allegion LCN Benchmark AU9100 Series Allegion LCN Benchmark AU9100 Series Low Energy Operators Installation Manual LCN Low Energy Operators should be installed in accordance with the current Allegion LCN installation instructions. Commissioning

More information

5300 Series 5300 SERIES

5300 Series 5300 SERIES 5300 Series Hager 5300 Series Grade 1 door closer is ideal for schools, hospitals, and other high abuse and high traffic environments. It is constructed of an aluminum alloy and provides smooth door control.

More information

General Information 351 Series Powerglide

General Information 351 Series Powerglide General Information Closer Spring Adjustment (not shown) Effects the entire cycle of the door closer movement Used to size closer for application requirements Determines the amount of force with which

More information

ROFU TJ 152-A. Y ALE SECURITY GROUP 50BC Series Door Closer. 50BC Series Door Closers. Sizing Chart for Installations. Ordering Information

ROFU TJ 152-A. Y ALE SECURITY GROUP 50BC Series Door Closer. 50BC Series Door Closers. Sizing Chart for Installations. Ordering Information ROFU 50BC Series Door Closers Specifications U.L. Listing All Yale 50 Series Door Closers with non-hold-open arms are listed by Underwriters Laboratories, Inc. for use on labeled fire doors. Tri-Pack Closer

More information

GT 710. Surface-Mounted, Low Energy, ADA*, Fire-Rated Swing Door Operator PRODUCT FEATURES

GT 710. Surface-Mounted, Low Energy, ADA*, Fire-Rated Swing Door Operator PRODUCT FEATURES GT 710 Surface-Mounted, Low Energy, ADA*, Fire-Rated Swing Door Operator The GT 710 operates in both automatic and manual modes. It features a 2-60 second hold-open range and a push-n-go feature. The GT

More information

*28101* 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT. Table of Contents.

*28101* 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT. Table of Contents. *28101* 28101 4630, 4640 Electric Auto Equalizer Series 4600 Electronic Low Energy Operator Installation Instructions 4630 PULL SIDE MOUNT 4640 PUSH SIDE MOUNT Table of Contents General Information...2

More information

NON-SIZED SIZED HANDED

NON-SIZED SIZED HANDED 4410ME SERIES TOP JAMB (PUSH SIDE) MOUNTING The 4410ME SENTRONIC is a heavy duty, electrically controlled closer/holder designed to provide infinitely adjustable hold-open for fire and smoke barrier doors.

More information

Design Guidelines and Standards Manual University of Cincinnati

Design Guidelines and Standards Manual University of Cincinnati SECTION 08710D - A. SPECIFICATIONS FORMAT 1. It is preferred that this section include all items of door hardware. Window hardware and operators should be specified in the window section. This approach

More information

7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor

7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor 7100SZ Series SafeZone Multi-Point Closer/Holder with Motion Sensor INTRODUCTION Designed with safety in mind, SafeZone takes door closers to a higher level. SafeZone uses a multi-point, electromechanical

More information

7500/7700 SERIES. Institutional Door Closer

7500/7700 SERIES. Institutional Door Closer Institutional Door Closer Page Revised Electronically 5/13, 10/13 7500/7700 SERIES overview The 7500 Series Door Closer offers customers the ideal combination of superior performance, strength and quality.

More information

Multi-point closer/holder with motion sensor 7100SZ DOOR CLOSER CATALOG

Multi-point closer/holder with motion sensor 7100SZ DOOR CLOSER CATALOG Multi-point closer/holder with motion sensor 7100SZ S E R I E S DOOR CLOSER CATALOG INTRODUCTION The 7100 Series SafeZone door closer safeguards occupants throughout a variety of facilities with the detection

More information

4031 Series Door controls

4031 Series Door controls 4031 Series Door controls Fire Rated: Tested on fire door assemblies in accordance with Australian Standards, refer fire door manufacturer for specific approval details The 4031 Series is a non-handed,

More information

DC5000 Series. Cam Action Door Closer

DC5000 Series. Cam Action Door Closer Series Cam Action Door Closer Introduction Table of Contents Introduction...2 Features... 3 Mountings... 4 Accessories... 5 How to Order... 6 Quick Codes... 6 Helpful Terms... 7 Specifications... 8 Applications

More information

*29268* 4600CS Electronic Low Energy Operator 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT. Table of Contents. Customer Service

*29268* 4600CS Electronic Low Energy Operator 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT. Table of Contents. Customer Service *29268* 29268 4630CS, 4640CS Electric Auto Equalizer Series 4600CS Electronic Low Energy Operator Installation Instructions 4630CS PULL SIDE MOUNT 4640CS PUSH SIDE MOUNT The 4600CS Series electric Auto-Equalizer

More information

Product Catalog. hardwaresuppliers.com

Product Catalog. hardwaresuppliers.com Product Catalog hardwaresuppliers.com 800-334-5625 2 Table of Contents Pages 3-5...1000 Series-Surface Mounted Pages 6-7...2030 & 3130 Series - Concealed Pages 8-15...4000 Series - Heavy-Duty Surface Mounted

More information

Overhead door holders/ stops

Overhead door holders/ stops Overhead door holders/ stops Quality hardware for superior door control Known throughout the industry as the overhead door holder specialist, Glynn-Johnson has made its name with state-of-the-art manufacturing

More information

Carey Automatic Door, LLC OSX ALL AIR (EXPLOSION PROOF) OPERATOR PACKAGES

Carey Automatic Door, LLC OSX ALL AIR (EXPLOSION PROOF) OPERATOR PACKAGES OSX ALL AIR (EXPLOSION PROOF) OPERATOR PACKAGES 100% PNEUMATIC (ALL AIR) & EXPLOSION PROOF OPERATORS 100% Pneumatic (ALL AIR) Door Systems: pneumatically operated with no electronics. Explosion Proof Door

More information

7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor

7100SZ Series SafeZone. Multi-Point Closer/Holder with Motion Sensor 7100SZ Series SafeZone Multi-Point Closer/Holder with Motion Sensor Page Revised Electronically 8/11 7100SZ Series SafeZone INTRODUCTION Designed with safety in mind, SafeZone takes door closers to a higher

More information

*24771* 4040SE DE Sentronic. 1 Voltage. 7 Regulation. 2 Track. 8 Door Closer Cover. 3 Spring Power. 4 Arm Installation. 5 Arm Screw.

*24771* 4040SE DE Sentronic. 1 Voltage. 7 Regulation. 2 Track. 8 Door Closer Cover. 3 Spring Power. 4 Arm Installation. 5 Arm Screw. *2477* 2477 SE Egress 4040SE DE Sentronic Installation Instructions This closer features mounting options for both standard and step-down double egress frames. Before beginning, determine which type of

More information

RTS88. Overhead Concealed Door Closer

RTS88. Overhead Concealed Door Closer RTS88 Overhead Concealed Door Closer RTS88 OVERHEAD CONCEALED CLOSER DORMA RTS88 OVERHEAD CONCEALED DOOR CLOSER Invisible door control Dependable and easy to install Architects are often challenged to

More information

Door Controls DOOR CLOSERS

Door Controls DOOR CLOSERS Door Controls Hager door closers offer architects, contractors, and building owners a superior product with proven reliability. In fact, our 5100, 5200, and 5300 Series Grade 1 models are the only closers

More information

1430/1431 SERIES POWERGLIDE DOOR CLOSERS

1430/1431 SERIES POWERGLIDE DOOR CLOSERS 1430/1431 SERIES POWERGLIDE DOOR CLOSERS 1430/1431 Series Powerglide Door Closers Table of Contents Page Cutaway Illustrations and Features 1 How to Select a Proper Closer 2 ADA Compliance 3 General Information

More information

Dor-O-Matic. Astro Swing Universal Control Box. Instruction Manual Universal Control Box

Dor-O-Matic. Astro Swing Universal Control Box. Instruction Manual Universal Control Box Dor-O-Matic Astro Swing Universal Control Box Instruction Manual 85425-900 Universal Control Box Factory Authorized Door Leaf Size & Weight: Type Width per Leaf Max. Weight per Leaf Single Door 36" to

More information

Product Catalog Phone: Fax:

Product Catalog Phone: Fax: Product Catalog Phone: 800-321-9602 Fax: 800-328-6070 LCN 2 Table of Contents and Finish Information Pages 3-5...1000 Series-Surface Mounted Pages 6-7...2030 & 3130 Series - Concealed Pages 8-14...4000

More information

351 Series Door Closers Models: Finishes: BHMA BHMA Description

351 Series Door Closers Models: Finishes: BHMA BHMA Description Door Closers Adams Rite provides Surface Applied and Pocket Closers from Sargent for controlling the closing of The RITE Door. 351 Series The 351 Powerglide line of surface door closers has been engineered

More information

*HINGE (pull) side mount shown COVER ACCESSIBILITY NON-HANDED NON-SIZED AVB**

*HINGE (pull) side mount shown COVER ACCESSIBILITY NON-HANDED NON-SIZED AVB** CLOSER MOUNTS *HINGE (PULL) SIDE TOP JAMB (PUSH SIDE) PARALLEL ARM (PUSH SIDE) 4040XP SERIES The 4040XP is LCN s most durable and flexible heavy duty closer designed for institutional and other demanding

More information

JACKSON CORPORATION Series

JACKSON CORPORATION Series Introduction The Jackson Grade 2 Overhead Concealed Closer has been the leader in the industry for over 35 years.the closer is manufactured in the U.S.A. under strict ISO 9000 guidelines and is designed

More information

General Information 281 Series Powerglide

General Information 281 Series Powerglide General Information All Weather Fluid All 281 Series closers are equipped with fluid that allows the units to operate effectively in extreme temperatures without readjustment. Finishes Powder coated and

More information

Overhead Concealed Door Closer DORMA RTS88

Overhead Concealed Door Closer DORMA RTS88 Overhead Concealed Door Closer DORMA RTS88 Overhead Concealed Door Closer A complete line of accessories is available for wood, aluminum, and hollow metal applications, both single and double-acting center

More information

Finishes/Colors/ Powder Coat

Finishes/Colors/ Powder Coat Features The 4030 is a cast iron, universal closer designed specifically for doors in moderate traffic conditions. This versatile closer compliments the rest of the heavy duty 4000 and offers the choice

More information

*4110 HCUSH mount shown

*4110 HCUSH mount shown *PARALLEL ARM (PUSH SIDE) MOUNT The 4110 SMOOTHEE is LCN s best performing heavy duty closer designed specifically for institutional and other rugged high traffic applications. FEATURES Standard 4110 series

More information

268, 269 & 278. Concealed Door Closers

268, 269 & 278. Concealed Door Closers 268, 269 & 278 Concealed Door Closers Copyright 2004-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents General Information....3 268 Features and Benefits...4

More information

EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES

EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES WIKK INDUSTRIES, INC. MasterFormat 95 SECTION 08480 MasterFormat 04 SECTION 08 42 36 EXTRUDED ALUMINUM BALANCED DOORS AND ENTRANCES PART 1 GENERAL 1.1 DESCRIPTION A. Work included: Entrance and vestibule

More information

422 Series. Cam Action Door Closer

422 Series. Cam Action Door Closer Cam Action Door Closer Copyright SARGENT Manufacturing Company 2005-2018. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is

More information

7100SZ Series SafeZone Installation and Instruction Manual

7100SZ Series SafeZone Installation and Instruction Manual 7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 80-9371-0081-00 (10-10) Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 5 for template) 3 1 Push Side Applications

More information

Surface Applied Door Closers DORMA TS93

Surface Applied Door Closers DORMA TS93 Surface Applied Door Closers DORMA TS93 DORMA TS93 Surface Applied Door Closers The TS93 System in Contur Design represents the pinnacle of surface applied closers because of its unique cam and roller

More information

LCN 4040 SERIES. CLOSER MOUNTS HINGE (PULL SIDE) (Shown) TOP JAMB (PUSH SIDE) PARALLEL ARM (PUSH SIDE)

LCN 4040 SERIES. CLOSER MOUNTS HINGE (PULL SIDE) (Shown) TOP JAMB (PUSH SIDE) PARALLEL ARM (PUSH SIDE) CLOSER MOUNTS HINGE (PULL SIDE) (Shown) TOP JAMB (PUSH SIDE) PARALLEL ARM (PUSH SIDE) The 4040 SUPER SMOOTHEE is LCN s most flexible heavy duty closer designed for institutional and other rugged high traffic

More information

Power drill Center punch Wire stripper

Power drill Center punch Wire stripper Pull Side Applications with Slide Track (7110SZ, 7150SZ) (see page 7 for template) 7100SZ Series SafeZone Installation and Instruction Manual Patent Pending 3 1 Push Side Applications with Double Lever

More information

Pivot Sets and Components DORMA LM

Pivot Sets and Components DORMA LM Pivot Sets and Components DORMA LM Pivot Sets and Components Whatever your pivot requirements, turn to DORMA and put the weight of your door on our pivots. DORMA s commitment to quality is your assurance

More information