A.10 CHRONO FOR PIVOTING WINDOWS. Contents. Horizontal and vertical pivoting windows

Transcription

1 A.10 Hizontal and vertical pivoting windows CHRONO FOR PIVOTING WINDOWS Contents 1. General characteristics A Base set n A Centre locking set n A Selection of rods n A Handles A Straight handles series 502 A Rounded handles series 5020 A Installation instructions A Preparation A Cut-outs f handle with central fixing holes A Cut-outs f handle with off centre fixing holes A Cut-outs rod transmission A Order table A General infmation A Waregemstraat 5 - B-9870 Zulte - Belgium Tel Fax coercial@sobinco.com -

2 1. General characteristics New totally clampable CHRONO pivoting window system based on the CHRONO turn and tilt technology. All parts are made of non-croding materials. Size range: 1 Hizontal pivoting window: vent width: vent height: vent weight: max. 180 kg 2 Vertical pivoting window: vent width: vent height: vent weight: max. 120 kg 3 The system is suitable f profiles with the following dimensions: see drawing. H B Fb Fh FFh FFb Dimensions out of standard range on request! Hizontal pivoting window Vertical pivoting window N.B.! The minimum vent height (f hizontal pivoting windows) the minimum vent width (f vertical pivoting windows) is section related. The minimum vent height minimum vent width must be checked to select the crect perimeter locking set, based on the sections used. The base sets are operated by series 502 and 5020 handles. Handles are not included in the base set. Perimeter locking sets are suitable f series 2600 and 490 pivots. Pivots are not included in the base set. The system can be used f hizontal and vertical pivoting windows. The base set is drawn with left hand handle: see page A If you use a right hand handle you have to assemble the base set mirr image. Very quick assembly by means of: new revolutionary rod connection system; special connections between the different components; connection piece is clipped over the fk of the handle; clamping wedges positioned with jigs; preassembled components and screws; easy access to fixing and adjustment screws. A.10.02

3 2. Base set n Vent width Fb = Vent height Fh = , 10042, 10043, 10044, 10045, drive pin connection piece handle connect pivot bypass connect connection piece bolt clip locking roller on plate wedge cner transmission 2 M5x35 screw 2 M5 rivnut (2,3,4,5,6)-555 rod transmission Base set Y () from... to ,5-29, ,5-34, ,5-39, ,5-44, ,5-49, ,5-24,5 Only f positioning of Remove after assembly. A.10.03

4 3. Centre locking set n Vent width Fb = (2, 3, 4, 5, 6) wedge Windows with vent width from 1200 to 1800 require an additional wedge n at the top and at the bottom. Vent width Fb = (2, 3, 4, 5, 6) wedge wedge Windows with vent width from 1801 to 2400 require a further additional wedge n at the top and at the bottom. A.10.04

5 4. Selection of rods n The system consists of 10 transmission rods with different lengths: , ,.... The adjustment range of each rod is 50. H B Fb Fh FFh FFb A.10.05

6 5. Handles 5.1. Straight handles series 502 left hand = illustrated right hand = opposite view Order Fk code A F K , ,5 8,5 18 throw K 5.2. Rounded handles series 5020 left hand = illustrated right hand = opposite view Order Fk code A F K , ,5 8,5 18 throw K The handles are available in different types: right hand handle (RIGHT), fixing holes out of centre (B), invisible fixing holes (VI), with cylinder (CYL), with fireman s axe handle (V) + grip n 505, with ventilation position (N). The standard type is left hand. A left hand handle is turned to the left to open the window. When dering please indicate the number of left hand and right hand handles. The fks are in steel zinc plated. Finish: grip and base in aluminium anodised polyester powder coated (me than 450 RAL colours). The handles n and n turn 180, all the others turn 150. Full documentation f all the handles f centre locking sets: see chapter A.15. A.10.06

7 6. Installation instructions wedges pivots A.10.07

8 7. Preparation 7.1. Cut-outs f handle with central fixing holes Fixing by means of rivnuts M5 N.B. It is always advisable to check handle clearance on the opening arc. This is particular imptant on smaller windows Cut-outs f handle with off centre fixing holes Fixing by means of rivnuts M5 N.B. It is always advisable to check handle clearance on the opening arc. This is particular imptant on smaller windows Cut-outs rod transmission A.10.08

9 8. Order table Fb= Fb= Fb= Fh= Y = 24, Y = 29, Y = 34, Y = 39, Y = 44, Y = 49, rods pivots series handle H B Fb Fh FFh FFb Order example: A hizontal pivoting window with overall vent width (Fb) 1700, overall vent height (Fh) 1300 and a Y-dimension of 37, with a glass thickness of 16 and a weight of 40 kg/m2. Note: To determine the precise vent weight see next page. Fittings to der: 1x base set x wedge x pivot series 490 ( series 2600) 1x handle Rods to der: 1x x x x x x A.10.09

10 9. General infmation The Chrono centre locking sets can be used within the Fh/Fb sizes and weight limitations indicated on the chart below. The sets are made of non-croding materials. The set should not be installed in crosive atmospheres. Sobinco cannot be held responsible f the malfunctioning of the centre locking set if any non-sobinco parts are used. The surface treatment of vent and frame must take place befe assembly of the set, as this will affect the wking of the gear. All parts must be assembled accding to the instructions as described in previous pages. Glazing must be in accdance with national standards. The window and gear should be kept clean and lubricated in accdance with our maintenance instructions (copy available on request). Hizontal pivoting window max. 180 kg Vertical pivoting window max. 120 kg Glass thickness without air gap kg/m² A.10.10