ALU 5200-TBT (150 kg)

Transcription

1 ALU 5200-TBT (150 kg) FBS Tilt-and-turn hardware for hinge clearance (BD) 5 mm with mishandling device (FBS) on the corner drive (EUL) KPW BD 5 Tilt point horizontal (KPW) Size range It is essential to adhere to the details of the system provider. Windows min. max. Patio doors max. Sash width (mm) 600 to Sash height (mm) 600 to Sash weight (kg) max. 100/150 max. 100/150 The following information from the aluminium planning manual must be observed: /2 Guidelines of the German quality association for locks and hardware (Gütegemeinschaft Schlösser und Beschläge e. V) - Document no. H LS001EN Application diagrams: - Sash weight up to max. 100 kg: Document no. H58.AWDLMS003EN - Sash weight up to max. 150 kg: Document no. H58.AWDLMS005EN Basic safety notes: - Document no. H LS001EN Abbreviations: - Document no. H LS002EN Adjustment options: - Document no. H LS004EN Profile recommendation: - Document no. H48.ZubhLS008EN Updated directory of the documents: - Document no. H LS005EN Table of contents Size ranges...1 Hardware overview... 2 Hardware list...3 Assembly and design variations...4 Sash dimensions...5 Frame dimensions... 6 Assembly instructions Page 1

2 ALU 5200-TBT BD 5 KPW (FBS-EUL) 150 kg Hardware overview Torque and tooling information Items Nm (± 0.25) , 207, 208, 401, 900, ,, 506, 517, , 904, PZ2 106, PH H H2 206 () H H /917 / Page 2

3 ALU 5200-TBT BD 5 KPW (FBS-EUL) 150 kg Hardware list Item Piece Designation Material no. VE Material no. VE H1 100 Handle ALU Si-line lockable/tbt See ALU handle overview, document no.: Only use in combination with coupling set H48.ZubhLS007en H2 103 ALU Globe lockable /TBT in ALU planning manual 1 H3 105 TITAN lockable/tbt 7 mm x 25, cam Ø 10 mm Only use in combination with gear set H4 107 ALU Globe RR lockable /TBT See Handle ALU Globe RR, document no.: H48.ZubhLS006en depending on FB/kg depending on kg H1/H2 H3/H4 dependent on system Accessories 1 Hinge side ALU 5200 BD 5 silver MMBS MMBS Bottom hinge Adjusting piece (replaced by item 924 with sash weight >100 kg) Cover cap Corner hinge Bottom hinge pin Clamping piece E Hinge pin Top hinge Stay hinge M5 x 7.5 countersunk screw M5 x 8.5 countersunk screw white RAL 9016 MMBS MMBS black RAL 9005 MMBS MMBS EV 1 MMBS MMBS Mill finish - 1 MMBS Top stay ALU size Additional stay ALU Additional stay Striker plate 1 Locking cam 1 Eccentric rivet MV stay striker Sash width > 1250 with top stay size kg Sash width > 1020 with top stay size 35 > 100 kg (FB > 1020 weight > 100 kg) (FB > 1250 weight 100 kg) MXSK MXSK Accessories set ALU BD kg > 100 kg - - MZBS M5 x 13 countersunk screw Supporting piece Adjusting piece S 1 Locking side ALU TBT KPW (with FBS on corner drive) Locking bolt TBT EUL clamping piece Corner drive, VSO-FBS 1 Striker Striker EUL VSO VSU corner drive Tilt lock Run-up block Tilt locking part Coupling set ALU (without FBS on gear) ALU coupling bracket M5 x 12 cheese head screw Gear set ALU (without FBS on gear) M6 ESG M5 x 35 countersunk screw M6 coupling screw MMVS MMVS Only use in combination with H1/H2 MMKL MMKL Only use in combination with H3/H4 (see drawing no. H48.ZubhLS005en) MMGI MMGI MV ALU-DK/TBT FH > 1250 (recommendation) Striker Slider VSU/BSO corner drive Locking part ALU FH > 2400 (recommendation) Locking cam 1 Eccentric rivet 1 Striker MV ALU slider FB > 1250 (recommendation) MMMV MMMV Striker Slider Handle support ALU Only use in combination with H1/H2 - - See table on page AV adjusting piece for compression MXBS MXBS Jig ALU 5200 additional screw connection for items 921 and 902 (> 100 kg; see page 6) MARB Page 3

4 ALU 5200-TBT BD 5 KPW (FBS-EUL) 150 kg Handle support assembly and design Observe assembly sequence Design variations for handle support (item 915) (H1/H2) USH (mm) 7-10 Z (mm) 2 X 7 mm X > mm MFHA > 2 3 MFHA MFHA > MFHA Sequence of installation in sash - without centre lock ( ) - with centre lock ( ) USH Assembly settings and installation sequence 1. to 4. Items + I. II. III. - Tighten firmly - Do not overtighten Break through the groove base of the sash groove Note: Put in eccentric rivet opening as demonstrated in the adjacent figures. > 100 kg Optional: Secure adjusting piece in the bottom hinge using allen key SW d. Note: Grease joint, do not oil! Note: Carefully press in hinge pin to the stop,do not hammer in! a. b. c. Page 4

5 ALU 5200-TBT BD 5 KPW (FBS-EUL) 150 kg Sash dimensions 234 (Additional stay) S3 Top stay size 35 = FB Top stay size 35 with additional stay = FB (>100 kg / FB > 1020) FB/2-426 MV 2) H1/H2 H3/H4 FH > 2000 (G1 = G2) 300 H1/H2 199 FH/3-110 FH/3-153 (FH > 2400) 2) (FH > 2400) 2) Ø10 Ø10 H3 (FH > 2400) 2) FH/3-163 Ø10 H4 X S4 = FH/2-230 (FH > ) 2) S4 = 2/3 FH (FH > 2400) 2) H3/H4 FH (sash height) S5 = FB/2-214 MV 2) FB (sash width) 1) Remove the rebate seal in the hinge gap area (minimum hinge gap 5 mm). 2) For installation recommendation for the centre locks and additional locks see page 3. Page 5

6 ALU 5200-TBT BD 5 KPW (FBS-EUL) 150 kg Frame dimensions MV 1) 85 Note: Remove adhesive residue from frame corners. 16,5 (FH > 2400) 1) FH/3 Handle height G1 +28 (H1/H2) (FH > 2400) 1) Handle height G (H3/H4) MV 1) min. 18 Drill hole 4.2 Sash weight >100 kg (for item ) (Overall frame clearance dimension) (MV from FH > 1250) For sash height> 2400 push FH/3 (FH > 2400) 1) downwards 1) FH/3 (FH > 2400) 1) (FH > ) 1) FH/3 125 Note: Remove adhesive residue from frame corners. MV 1) FB ) For installation recommendation for the centre locks and additional locks see page 3. SIEGENIA-AUBI KG Industriestraße 1-3 D Wilnsdorf Telephone Fax Page 6