Hydraulic Pilot Control Valves

Transcription

1 HYDRAULIC COMONENS HYDROSAIC RANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, MODENA (IALY) el: Fax: / INERNE: hansatmp@hansatmp.it H 73 / B / 103 / 0308 / E Hydraulic ilot Control Valves HANDLES MULIFUNCION ERGONOMIC AND KNOBS HVL/SVL SERIES HYDRAULIC ILO CONROLS RSVS/M SERIES SINGLE AND SECIONAL ILO CONROL VALVES 23 to 51 cm 3 /rev (1.4 to 3.1 cu.in/rev) 280 bar (4000 psi) peak pressure CVL SERIES HYDRAULIC ILO CONROLS RSVB/L SERIES ONE AND WO LEVER OERAED ILO CONROL VALVES HV SERIES HYDRAULIC ILO CONROLS RSV SERIES FOO EDALS SUH SERIES ILO SULY UNIS OIL SAMLING VALVE

2

3 CONENS Handles Hydraulic ilot Control HVL / SVL Series Single and Sectional ilot Control RSVS / M Series Hydraulic ilot Control CVL Series One and wo Lever Operated ilot Control Valves RSVB / L Series Hydraulic ilot Control HV Series Foot edal Hydraulic ilot Control RSV Series ilot Supply Units SUH Series Characteristic Curves Oil Sampling Valves H 73 / B / 103 / 0308 / E ag. 3

4 HANDLES MULIFUNCION ERGONOMIC AND KNOBS H 73 / B / 103 / 0308 / E ag. 5

5 HANDLES INRODUCION HANDLES AND K NOBS he handles and knobs included in this catalogue are available for fitting either to the extensive range of our pilot valve product he materials are chosen to be suitable for either internal or external use and are resistant to ultraviolet effects. hey are also suitable for a wide range of other environmental conditions. he s tandard s traight ergonomic handle is available with a range of switches and push buttons, while the MF E handle range is available with an extensive range of switches and push buttons to suit different operating and environmental conditions. he MF E handle range can be configured to s uit either left hand or right hand operation. BENEFIS R ange of knobs for individual lever control R ange of s traight levers, with and without s witches, for dual axis controls E xtens ive range of s tylis h multi functional lever options E xtensive range of electrical switch and button options Adaptable to both Hansa-mp s.r.l. and other manufacturers equipment C ircuits and connectors to cus tomer requirements S witch options allow left hand or right hand operation olerant to many environmental conditions High durability, low maintenance Different circuit arrangements can be accommodated within the handle and the wiring can be built into connectors to customer s pecifications. HANDLES E R GONOMIC AND KNOB MODE L CODING K - K SERIES KNOBS S - S SERIES ERGONOMIC see page 3 see page 4 K B = K nob without electric s witch S A = Handle without electric s witch K C = K nob without electric s witch SD = Handle with electric switch K J K K K L K = C onical handle with electric s witch = K nob without electric s witch = C onical handle without electric s witch = Spherical knob without electric switch SS SX SY = Handle with electric s witch to clos e and s afety button = Handle with electric s witch to clos e = Handle with electric switch dual rocker type KW = K nob with electric s witch SZ = Handle with electric s witch to clos e with detent ag. 6 H 73 / B / 103 / 0308 / E

6 K SERIES HANDLES ECHNICAL DAA Hydraulic ilot Control Valves KB KNOB without electric switch ø34 (1.34) KC KNOB without electric switch ø45 (1.77) KJ CONICAL HANDLE with electric switch ø32 (1.26) ø10 (0.39) 8 (0.315) 40 (1.575) 67 (2.64) 50 (1.97) 65 (2.56) 56 (2.21) M10 ø10 (0.39) ø10 (0.39) KK KNOB without electric switch ø60 (2.36) ype: SA 66.5 (2.62) KL CONICAL HANDLE without electric switch ø27 (1.06) wiring diagram 18 (0.71) K SHERICAL KNOB without electric switch M12 ø32 (1.26) 42 (1.65) 25 (0.98) ø45 (1.77) KW KNOB with electric switch ø8 (0.315) 42 (1.65) 21 (0.83) ø12 (0.47) wiring diagram H 73 / B / 103 / 0308 / E ag. 7

7 S SERIES HANDLES ECHNICAL DAA Hydraulic ilot Control Valves SA ERGONOMIC HANDLE without electric switch ø52 (2.05) SD ERGONOMIC HANDLE with electric switch ø52 (2.05) SS ERGONOMIC HANDLE with electric switch to close and safety button ø52 (2.05) ø39.5 (1.56) ø39.5 (1.56) 1 ø39.5 (1.56) 167 (6.575) 123 (4.84) 113 (4.45) 167 (6.575) 123 (4.84) 113 (4.45) 2 SX ERGONOMIC HANDLE with electric switch to close ø52 (2.05) ø39.5 (1.56) SY ERGONOMIC HANDLE ype: SA with electric switch dual rocker type ø52 (2.05) ø39.5 (1.56) SZ ERGONOMIC HANDLE with electric switch to close with detent ø52 (2.05) ø39.5 (1.56) 29(1.14) 20(.79) 15(.59) 29(1.14) 20(.79) 15(.59) 29(1.14) 20(.79) 15(.59) 167 (6.575) 123 (4.84) 113 (4.45) 167 (6.575) 123 (4.84) 113 (4.45) 167 (6.575) 123 (4.84) 113 (4.45) 29(1.14) 20(.79) 15(.59) 29(1.14) 20(.79) 56 (2.205) 15(.59) 167 (6.575) 123 (4.84) 113 (4.45) 29(1.14) 20(.79) 15(.59) M10 17 (0.67) ø19 (0.75) M10 17 (0.67) ø19 (0.75) M10 17 (0.67) ø19 (0.75) 1 wiring diagram 2 wiring diagram M10 17 (0.67) ø19 (0.75) M10 17 (0.67) ø19 (0.75) M10 17 (0.67) ø19 (0.75) wiring diagram wiring diagram wiring diagram ag. 8 H 73 / B / 103 / 0308 / E

8 HANDLES MFE MODE L C ODING MFE = Multi-function E rgonomic E X XXXXXX - XX - X X X X + X (see page 4) ush button/switch options A B C D = standard with micro switches rated for 3 A at 30 VDC = sealed version with microswitches rated for 3 A at 30 VDC + CB = isolated version (I 67) with micro switches rated for 0.4 A at 30 VDC = dual axis / 4 contacts waterproof micro switches rated for 2 A at 30 VDC (conforms with MIL standards) R oc ker s witc h (omit digit if not required ) his version is not available in combination with push button switches types B and D. = Horizontal mounting with function symbols, rated for 6 A at 250 VAC Q = Vertical mounting with function s ymbols, rated for 6 A at 250 VAC R = Long life vers ion (10 6 cycles), rated for 3 A at 30 VDC S = Waterproof I 68 rated for 10 A at 250 VAC (can be mounted in either horizontal or vertical position) Mounting adapter (see page 5) 0 = standard straight M10x1.5 1 = tilted 15 north 2 = tilted 15 east 3 = tilted 15 west 4 = combined tilting (15 north and 10 east) = LH handle 5 = combined tilting (15 north and 10 west) = R H handle 6 = with spherical joint, adjustable from 0 up to 20 in any direction 7 = as item 6 + bottom mounting adapter Gaiter c ollar (see page 6) O = basic version without provision for protection boot R = with provision for round boot S = with provision for square boot Wiring termination 0 = no leads 1 = flying leads 2 = with connector (maker and model number to be specified on order) S afety trigger in position 7 X = no s afety trigger = with safety trigger (available only red) ush button/switch in positions (not applicable for switch configuration B ) For each push button/switch, insert ID position numbers and colours (see 1 6 position) separated by - and omit ones that are not required (i.e. 8R -10G = red pus h button/s witch in pos ition 8 and green pus h button/switch in position 10) Note: pus h button/s witch in pos ition 8 is rated 0.4 A at 32 V DC and available only red ush button/switch in positions Insert ID letter for each push button/switch chosen on the following list and in progressive sequence from position 1 up to position 6: X = no button s witch B = blue G = green R = red Y = yellow W = white (available for C configuration only) L = s ignalling light H 73 / B / 103 / 0308 / E ag. 9

9 HANDLES MFE US H BUONS COMAIBILIY ABLE S KEY available combination not available Compatibility of pus h button/s witches and rocker switches combinations For S tandard B utton ype A ROCKER USH BUON Q R S USH BUON ROCKER Q R S Compatibility of pus h button/s witches and rocker switches combinations F or S ealed B utton ype B (Applicable only for push button/switches fitted into positions 1 up to 6 and safety trigger in position 7.) ag. 10 ROCKER USH BUON Q R S USH BUON ROCKER Q R S H 73 / B / 103 / 0308 / E

10 HANDLES MFE US H BUONS COMAIBILIY ABLE S KEY available combination not available Compatibility of pus h button/s witches and rocker switches combinations F or Is olated B utton ype C (*) Als o compatible in combination with a light (L) fitted in pos ition 1 (**) Als o compatible in combination with a light (L) fitted in pos ition 4 ROCKER USH BUON Q R S USH BUON ROCK ER Q R S * * * ** ** ** ** * Compatibility of pus h button/s witches and rocker switches combinations F or Dual Axis B utton ype D ROCKER USH BUON Q R S USH BUON ROCKER Q R S H 73 / B / 103 / 0308 / E ag. 11

11 HANDLES MFE BUON YES AND OSIION OIONS A SANDARD B SEALED MF E Multi F unction E rgonomic handle fitted with s tandard pus h button s witches (ype A) and vertical mounted rocker switch and s afety trigger (left view). MFE Multi Function E rgonomic handle fitted with sealed push button switches (ype B ) mounted on CB and mounting adaptor adjustable in any direction from 0 up to 20. ø10 (.39) ø14 (.55) Standard ush B utton S witc h ype A 2.5 (.10) 5 (.20) Sealed ush Button Switch ype B C ISOLAED D DUAL AXIS MF E Multi F unction E rgonomic handle fitted with 8 waterproof pus h button s witches (ype C ), two s ignalling LED's and a safety push button switch on front pos ition 8. MFE Multi Function E rgonomic handle fitted with 2 dual axis (4 contacts) waterproof mini push button s witches (ype D) to MIL standards ø18 (.71) ø17.5 (.69) 10 (.39) Is olated us h B utton S witc h ype C 6 (.24) Dual Axis us h Button Switch ype D ø17.5 (.69) ø10 (.39) 33 (1.30) 9 (.35) Snap push button s witc h (as fitted to front of handle in pos ition 8) S ignalling LE D (code L) 4.5 (.18) Safety rigger (as fitted to front of handle in position 7) ag. 12 H 73 / B / 103 / 0308 / E

12 HANDLES MFE MOUNING ADA E R S 0 SANDARD SRAIGH 1 ILED 15 o FORWARD 2 ILED 15 o RIGH HAND 15 o 15 o 146 (5.75) ypical Handle Height for the MFE R ange ø16 (0.63) ø20 (0.79) ø20 (0.79) 11 (0.43) 7 (0.275) 13 (0.51) 11 (0.43) 7 (0.275) 17 (0.67) 11 (0.43) 7 (0.275) 17 (0.67) M10 x 1.5 M10 x 1.5 M10 x ILED 15 o LEF HAND 4 COMBINED ILING RIGH HAND 15 o 10 o 15 o 7 WIH BALL JOIN AND MOUNING ADAER 20 o MAX 20 o MAX ø20 (0.79) 7 (0.275) 17 (0.67) 11 (0.43) 7 (0.275) 11 (0.43) M10 x 1.5 M10 x (0.67) ø20 (0.79) 30 (1.18) M30 x 1 5 COMBINED ILING LEF HAND 6 WIH BALL JOIN 10 o 15 o 20 o MAX 20 o MAX 10 (0.39) 7 (0.275) M27 x o M30x1 ø26 ø15 11 (0.43) M10x (0.67) 7 (0.275) 30 (1.18) M30 x 1 12 (0.47) 9.5 (0.375) 5 (0.20) ø20 (0.79) H 73 / B / 103 / 0308 / E ag. 13

13 HANDLES MFE ROCKER SWICHES HORIZONALLY MOUNED SWICH Q VERICALLY MOUNED SWICH 31.5 (1.24) 14 (0.55) 31.5 (1.24) his vers ion has function symbols and is rated for 6A at 250 VAC 25 (0.985) his vers ion has function symbols and is rated for 6A at 250 VAC E lectrical life = 10,000 operations E lectrical life = 10,000 operations R LONG LIFE SWICH S WAERROOF SWICH I68 W aterproof and I 68 rated for 10A at 250 VAC 31.5 (1.24) 31 (1.22) Can be mounted either horizontally or vertically 14 (0.55) he long life vers ion (10 6 ) is rated for 3A at 30 VDC E lectrical life = 10 6 operations if diode suppression is fitted across the solenoid 16 (0.63) E lectrical life = 50,000 operations ag. 14 H 73 / B / 103 / 0308 / E

14 HANDLES ROECIVE BOOS R ROUND ROECION BOO SHOWING GAIER COLLAR FOR SANDARD SRAIGH MOUNING ADAER ø20 (0.79) SHOWING GAIER COLLAR FOR ILED MOUNING ADAER ø20 (0.79) 3 (0.12) 79.5 (3.13) 3 (0.12) 79.5 (3.13) ø16 (0.63) ø16 (0.63) S SQUARE ROECION BOO SHOWING GAIER COLLAR FOR SANDARD SRAIGH MOUNING ADAER ø40 (1.575) SHOWING GAIER COLLAR FOR ILED MOUNING ADAER ø40 (1.575) 5 (0.20) 3 (0.12) 5 (0.20) 3 (0.12) 92.4 (3.64) 92.4 (3.64) 86 (3.39) 86 (3.39) 97 (3.82) 97 (3.82) H 73 / B / 103 / 0308 / E ag. 15

15 HVL / SVL SERIES HYDRAULIC ILO CONROL H 73 / B / 103 / 0308 / E ag. 17

16 HVL/ SVL SERIES INRODUCION LOADER YE ILO CONROLS H V L and S V L ilot C ontrol Valves are part of the comprehensive range of our Hydraulics product, and with the inclus ion of electrical detents are designed specifically for Wheeled Loader applications. he product is s upported by an extens ive range of control curve characteristics and handle options, and can be supplied to control either two service or three service loader applications. Our engineers can offer specialist support to optimis e this product to s uit your application. he product is s upported by a comprehens ive S ales and S ervice facility around the world. BENEFIS C ompact and light weight All ports on bottom face for ease of installation S tylis h good looks s uitable for modern cabs Operator insulated from high temperature components roven, simple pressure reducing elements W ide range of low hys teres is, high accuracy pressure control curves W ide range of electrical options in both standard and multi-functional ergonomic handles E lectrically releas able detents available as required Low effort lever control HVL/SVL SERIES MODE L CODING XVL 1 XX XX XXX X X Return spring 0 = Standard: 1.4 to 2.8 dan 1 = Light: 3.0 to 4.5 dan 2 = Medium: 7.5 to 13.8 dan Gaiter R = Round S = Square Metering curve see CV CHARACERISICS catalogue Handle type W = Without Handle see HANDLES catalogue Basic model type 0 4 = o control 2 s ervices 0 6 = o control 3 s ervices 1 = Design Mark H V L = Hydraulic ilot C ontrol S V L = Hydraulic ilot C ontrol Example: ordering number: HVL 1 06 S A 015 S 1 model number: HVL 1 06 S A 015 S 1 / (assigned number) ag. 18 H 73 / B / 103 / 0308 / E

17 HVL SERIES ECHNICAL DAA Hydraulic ilot Control Valves HVL104 For control of B oom and B ucket 125 (4.92) 42.7 (1.68) 85 (3.35) SHOWN WIH ROUND BOO FIED 27 (1.06) U4 U3 100 (3.94) U2 FRON 27 (1.06) ø54 (2.13) 45 (1.77) 87.5 (3.44) 4 holes ø7.0 thro equispaced as shown on 110 CD ø40 (1.575) MAX 20 o 1 FOR S E R VICE MAX 27 o 2 FOR SERVICES ø104.3 (4.11) 102 (4.02) (0.565) FLANGE 75 (2.95) 59 (2.32) (11.04) 115 (4.53) Amp sealed connector housing, part number and Double-lock plate, part number for cap OWERDOWN CIRCUI DIAGRAM U3 U4 U2 CROWD I RAISE H 73 / B / 103 / 0308 / E ag. 19

18 HVL SERIES ECHNICAL DA A Hydraulic ilot Control Valves HVL106 F or control of Boom, Bucket and Auxiliary 85 (3.35) 42.7 (1.68) ø131 (5.16) 105 (4.13) 87.5 (3.44) 54 (2.13) 42.5 (1.67) 27 (1.06) U2 U3 U4 U (3.15) 95 (3.74) 110 (4.33) U5 SHOWN WIH SQUARE BOO FIED 4 holes ø6.5 thro equispaced as shown on 108 CD 54 (2.13) 27 (1.06) FRON AUXILIARY SERVICE 26 o ø40 (1.575) AUXILIARY SERVICE 26 o MAX 21 o 1 FOR SERVICE MAX 26 o 2 FOR SERVICES ø27 (1.06) 25 o 20 (0.79) (4.55) 258 (10.16) 75.5 (2.97) 57 (2.24) 5 (0.20) 3 (0.12) (4.87) 112 (4.41) 230 (9.06) CIRCUI DIAGRAM OWER DOWN FLOA (1) I (4) AUXILIARY (5) FRON U3 U2 U4 U5 U6 I CROWD (2) RAISE (3) AUXILIARY (6) ag. 20 H 73 / B / 103 / 0308 / E

19 SVL SERIES ECHNICAL DAA Hydraulic ilot Control Valves SVL104 For control of B oom and B ucket 134 (5.28) 52 (2.05) 26 (1.02) 94 (3.70) 50 (1.97) U2 U4 U (3.72) 4 holes ø9.0 thro MOUNING ANEL DEAILS (O VIE W) 50 (1.97) 23 (0.91) 118 (4.65) 96 (3.78) 11 (0.43) FRON 4 holes ø9.0 thro FRON 6 44 (1.73) 6 (0.24) 99.5 (3.92) 96 (3.78) 21 o 21 o BUCKE 15 o BOOM SHOWN WIH ROUND BOO FIED 255 (10.04) (5.04) 75.5 (2.97) 56 (2.20) 8 (0.315) 4 2 I OWER DOWN FLOA 4 FRON 1 CIRCUI DIAGRAM U3 U2 U4 2 3 CROWD RAISE H 73 / B / 103 / 0308 / E ag. 21

20 SVL SERIES ECHNICAL DAA Hydraulic ilot Control Valves SVL106 For c ontrol of B oom, B uc ket and Auxiliary 144 (5.67) MOUNING ANEL DEAILS (O VIE W) 100 (3.94) 134 (5.28) 52 (2.05) 26 (1.02) 50 (1.97) U6 U5 50 (1.97) U2 U4 U3 6 holes ø9.0 thro 94.4 (3.72) 118 (4.65) 23 (0.91) 96 (3.78) 11 (0.43) 50 (1.97) FRON 4 holes ø9.0 thro FRON 6 (0.24) (5.89) 44 (1.73) 6 (0.24) 146 (5.75) ø27 (1.06) 25 o BUCKE 15 o BOOM 21 o 21 o SHOWN WIH SQUARE BOO FIED 128 (5.04) 75.5 (2.97) 56 (2.20) 8 (0.315) 255 (10.04) 210 (8.27) AUXILIARY 5 4 I FRON OWER DOWN FLOA 1 CIRCUI DIAGRAM U3 U2 U4 U5 U AUXILIARY CROWD RAISE ag. 22 H 73 / B / 103 / 0308 / E

21 RSVS / M SERIES SINGLE AND SECIONAL ILO CONROL VALVES 23 to 51 cm 3 /rev (1.4 to 3.1 cu.in/rev) 280 bar (4000 psi) peak pressure H 73 / B / 102 / 0308 / E ag. 23

22 RSVS SERIES INRODUCION HYDRAULIC ILO CONROL RSV ilot Control Valves are part of the comprehensive range of our Hydraulics product. his product, with its individual lever control, supported by an extensive range of control curve characteristics and a choice of handle options, makes it suitable for a wide range of both mobile and industrial applications. Our engineers can offer specialist support to optimis e this product to s uit your application. he product is s upported by a comprehens ive S ales and S ervice facility around the world. BENEFIS C ompact and light weight S ervice ports on bottom face with s upply and return ports on side faces for ease of installation S imple to mount Compatible with a wide range of equipment Operator is insulated from high temperature components roven, simple pressure reducing elements Wide range of low hysteresis, high accuracy, pressure control curves R ange of electrical options within handle options Low effort lever control RSVS SERIES MODE L CODING RSVS XX X XX F X Return spring 0 = Standard: 1.4 to 2.8 dan 1 = Light: 3.0 to 4.5 dan 2 = Medium: 7.5 to 13.8 dan 3 = Heavy: 10.0 to 19.0 dan F = S tandard C ontrol lunger Metering curve see C V C H A R AC E R I S I C S section Handle type see H A N D L E S section W = Without Handle Basic model number O 1 O2 O3 O 4 O 5 O 6 O 7 O 8 O9 = 2 service ports with lever spring returned into neutral = 2 service ports with lever detented in any position = 2 service ports with lever detented in any position and neutral position sensor = 2 service ports with lever detented at both stroke ends = 2 s ervice ports with lever detented in neutral pos ition = 2 s ervice ports with lever detented in neutral pos ition and friction for detent in any pos ition = 2 service ports with lever detented at stroke end of side and spring returned to neutral on U2 side = 2 service ports with lever detented at stroke end of U2 side and spring returned to neutral on side = 2 service ports with square mounting flange / rubber boot and multi-function ergonomic handle R S V S = S ingle Unit Hydraulic ilot Valve S eries S ag. 24 H 73 / B / 102 / 0308 / E

23 RSVS SERIES ECHNICAL DAA SINGLE LEVER ILO CONROL VALVES YE S S ingle lever pivot control valves type S are fitted with a protective rubber cover. hey can easily be modified from one model 44 (1.73) 30 (1.18) 9 (.355) U2 to another simply by replacing some of the parts which are mounted on the lever mechanism, inside the protective cover; therefore installation dimensions are common for any model. ø27 (1.06) ø14 (.55) 4 (0.16) UNLOCKING SR OKE 36.8 (1.49) 95 (3.74) 110 (4.33) 26 o 26 o ø27 (1.06) he following chart shows a view of all the control handles and knobs which may be supplied with the type S control valve. For details of each type see the Handles catalogue. All models in the type S range can be fitted with a multi-function ergonomic handle. S ee next page. YE SA YE SD YE SS YE SX YE SY YE SZ (4.43) 190 (7.48) for handle type KL (as drawn) 20 (0.79) 81.5 (3.21) 3 (0.12) type K L control handle shown 35 (1.38) 25 (0.985) ø7 (0.275) YE KB YE KC YE KJ 70 (2.76) 80 (3.15) HYDRAULIC CIRCUI DIAGRAM YE KK YE K YE KW plus type KL as shown on main drawing U2 H 73 / B / 102 / 0308 / E ag. 25

24 RSVS SERIES ECHNICAL DAA SINGLE LEVER ILO CONROL VALVE RSVS09 Hydraulic ilot Control Valves F or handle options available in the Multi-function E rgonomic range, see the H a ndle s catalogue. ELECRIC CIRCUI DIAGRAM (0.24) 10 (0.39) (0.24) 100 (3.94) 88 (3.46) 80 (3.15) 70.7 (2.78) HYDRAULIC CIRCUI DIAGRAM 100 (3.94) 88 (3.46) 70.7 (2.78) 30 (1.18) U2 50 (1.97) 44 (1.73) 34 (1.34) U2 6 (0.24) (0.24) 35 (1.38) (3.19) 6.5 (0.26) x 4 26 o 26 o (4.43) 263 (10.35) 35 (1.38) 20 (0.79) 25 (0.985) (3.46) 100 (3.94) 80 (3.15) 88 (3.46) 100 (3.94) ag. 26 H 73 / B / 102 / 0308 / E

25 RSVM SERIES INRODUCION HYDRAULIC ILO CONROL RSV ilot Control Valves are part of the comprehensive range of our Hydraulics product. his product, with its individual lever control, supported by an extensive range of control curve characteristics and a choice of handle options, makes it suitable for a wide range of both mobile and industrial applications. Our engineers can offer specialist support to optimis e this product to s uit your application. he product is s upported by a comprehens ive S ales and S ervice facility around the world. BENEFIS Compact and light weight Service ports on bottom face with supply and return ports on side faces for ease of installation Simple to mount Compatible with a wide range of equipment Operator is insulated from high temperature components roven, simple pressure reducing elements Wide range of low hysteresis, high accuracy, pressure control curves Range of electrical options within handle options Low effort lever control RSVM SERIES MODEL CODING RSVM XX X XX F X R eturn spring 0 = S tandard: 1.4 to 2.8 dan 1 = Light: 3.0 to 4.5 dan 2 = Medium: 7.5 to 13.8 dan 3 = Heavy: 10.0 to 19.0 dan F = S tandard Control lunger Metering curve see CV CHARACERISICS Handle type see HANDLES section W = Without Handle Basic model number section Ordering key for multiple sections assembly of RSVM series modules as follows: Settle the model number of each individual section, as shown on the coding chart, starting from the inlet section (port side) to the outlet section (port side) and put them in sequence. For example: the complete model number of a 2 sections assembly made of M01 and M02 combination is: RSVM01L001F0 + RSVM02L015F0 O1 O2 O3 O4 O5 O6 O7 O8 = 2 service ports with lever spring returned into neutral = 2 service ports with lever detented in any position = 2 service ports with lever detented in any position and neutral position sensor = 2 service ports with lever detented at both stroke ends = 2 service ports with lever detented in neutral position = 2 service ports with lever detented in neutral position and friction for detent in any position = 2 service ports with lever detented at stroke end of side and spring returned to neutral on U2 side = 2 service ports with lever detented at stroke end of U2 side and spring returned to neutral on side RSVM = Sectional Hydraulic ilot Valve Series M H 73 / B / 102 / 0308 / E ag. 27

26 RSVM SERIES ECHNICAL DAA SECIONAL ILO CONROL VALVES YE M S ectional pilot control valves type M are particularly s uitable for thos e applications where it is neces s ary to 44 (1.73) 30 (1.18) 9 (.355) U2 reduce to a minimum installation dimensions, even when a relatively high number of s ervices has to be controlled. S ectional pilot control valves type M are extremely flexible: a wide range of control levers is available for any model: s ingle units with as s embly ø27 (1.06) ø14 (.55) 4 (0.16) UNLOCKING SR OKE 36.8 (1.49) 95 (3.74) 110 (4.33) 26 o 26 o ø27 (1.06) kit or multiple units fully as s embled can be s upplied; eas y modification from one model to another by replacing some of the parts mounted on the lever mechanism, within the rubber cover. ype M control valves may be fitted with the following knob types. F or details see the Handles catalogue. YE KB YE KC YE KJ plus type KL as shown on main drawing (4.43) 190 (7.48) for handle type KL (as drawn) 20 (0.79) 35 (1.38) 25 (0.985) type K L control handle shown 3 (0.12) ø22 ø22 (0.87) (0.87) 80 (3.15) HYDRAULIC CIRCUI DIAGRAM U2 ag. 28 H 73 / B / 102 / 0308 / E

27 RSVM SERIES ECHNICAL DAA SECIONAL ILO CONROL VALVES YE M Hydraulic ilot Control Valves * S pecial centre-line dis tances of 60mm and 80mm are also available (1.75) 44.5 (1.75) Angled levers are available to customer's specifications as are levers of varying heights. U2 U4 U6 F or details pleas e contact our echnical Department (1.49) 95 (3.74) 110 (4.33) U3 U5 26 o 26 o 9 (0.355) ø27 (1.06) type K L control handle shown ø14 (0.55) 4 (0.16) UNLOCKING SR OKE 194 (7.64) (4.43) 20 (0.79) 3 (0.12) (12.07) 35 (1.38) 25 (0.985) 80 (3.15) * 44.5 (1.75) * 44.5 (1.75) 119 (4.69) HYDRAULIC CIRCUI DIAGRAM 131 (5.16 U2 U3 U4 U5 U6 H 73 / B / 102 / 0308 / E ag. 29

28 CVL SERIES HYDRAULIC ILO CONROLS H 73 / B / 102 / 0308 / E ag. 31

29 CVL SERIES INRODUCION FEAURES: - Aluminium body for light weight execution - Auxiliary function integrated in a single body - Wide range of metering curve - Magnetic (12 or 24 VDC) or mechanical detent with prefeel ramps - Optional linkage between main and auxiliary function - Rubber boot protection ARIBUES: Input pressure: Min. 25 bar Max. 50 bar Back pressure: 3 bar Max. at port Hysteresis: +/- 0,5 bar Max. Flow: Min. 5 l/min Max. 25 l/min Leakage: Max mm2/sec and 30 bar supply pressure Fluid temperature: -20 to +80 C Fluids: Mineral oils HM and HV Fluid cleanliness: 21/16/13 to ISO 4406:1999 ag. 32 H 73 / B / 102 / 0308 / E

30 CVL SERIES OVERALL DIMENSIONS Max.for 1 service 30 Max. for 2 services 98,1 12 Ø 21 Ø NAME LAE C IR C UI DIAG R AM 69 = = = = U3 U2 U4 U6 U5 7 (4 os.) OWERDOWN FLOA (1) A I (4) AUXILIARY (6) U3 131 = = 119 = = 81 = = 44 = = U2 U4 U5 U6 VIEW FROM A 17 9,5 119 = = 131 = = Ø 12 (4 os.) CROWD (2) RAISE (3) AUXILIARY (5) H 73 / B / 102 / 0308 / E ag. 33

31 CVL SERIES ORDERING KEY CVL106 E X X X X K 5 6 X X X X X B = ¼ BS orts (Standard option) M = Metric M14x1.5 orts S = 7/16-18 UNF SAE o rts 1 = 12 VDC Magnets 2 = 24 VDC Magnets W = Without linkage L = With linkage E = Electric detent on port 6 M = Mechanical detent on port 6 X = No detent E = Electric detent on port 5 M = Mechanical detent on port 5 X = No detent Metering curve no on port 6 (see catalogue) Metering curve no on port 5 (see catalogue) Knob type on auxiliary (see knob catalogue) E = Electric detent on port 4 M = Mechanical detent on port 4 X = No detent E = Electric detent on port 3 M = Mechanical detent on port 3 X = No detent E = Electric detent on port 2 M = Mechanical detent on port 2 X = No detent E = Electric detent on port 1 M = Mechanical detent on port 1 X = No detent Metering curve no on port 4 (see catalogue) Metering curve no on port 3 (see catalogue) Metering curve no on port 2 (see catalogue) Metering curve no on port 1 (see catalogue) W = Without handle S = Straight handle (see handle catalogue) E =Ergonomic handle (see MFE catalogue) ag. 34 H 73 / B / 102 / 0308 / E

32 RSVB / L SERIES ONE OR WO LEVER OERAED ILO CONROL VALVES H 73 / B / 102 / 0308 / E ag. 35

33 RSVB/ L SERIES INRODUCION Hydraulic ilot Control Valves HYDRAULIC ILO CONROL RSV ilot Control Valves are part of the comprehensive range of our Hydraulics product. his product, with its individual lever control, supported by an extensive range of control curve characteristics makes it suitable for a wide range of applications. Our engineers can offer specialist support to optimis e this product to s uit your application. he product is s upported by a comprehens ive S ales and S ervice facility around the world. BENEFIS C ompact and light weight All ports on bottom face for ease of installation S imple to mount C ompatible with a wide range of product Operator is insulated from high temperature components roven, simple pressure reducing elements Wide range of low hysteresis, high accuracy, pressure control curves Low effort lever control with spring centred and detented versions available RSVB/ L SERIES MODE L CODING RSV XXX X XXX F X XX * S huttle block * * omit if no s huttle block is required S 1 = o s uit s ingle lever model S 3 = o suit double lever model Return spring 0 = Standard: 1.4 to 2.8 dan 1 = Light: 3.0 to 4.5 dan 2 = Medium: 7.5 to 13.8 dan 3 = Heavy: 10.0 to 19.0 dan F = S tandard C ontrol lunger Metering curve see C V C H A R AC E R I S I C S section Handle type W = Without Handle K = R ound K nob (standard) s ee H A N D L E S section for other options Basic model number Double lever S ingle lever B O1 LO1 B O2 LO2 B O3 see pages LO3 see pages B O4 3 and 4 LO4 5 and 6 B O5 LO5 B O6 LO6 R S V = Hydraulic ilot Valve S eries ag. 36 H 73 / B / 102 / 0308 / E

34 RSVB SERIES ECHNICAL DAA Hydraulic ilot Control Valves BO1 ILO OERAED CONROL BO2 ILO OERAED CONROL 2 side levers with return spring 2 side levers with mechanical detent 109 (4.29) 61 (2.40) 109 (4.29) 61 (2.40) ø12 (0.47) 34 o ø12 (0.47) 34 o 95 (3.74) 323 (12.72) 90.5 (3.56) 7 (0.275) 41.5 (1.63) 323 (12.72) 107 (4.21) 12 (0.47) 90.5 (3.56) 7 (0.275) 41.5 (1.63) ø7 (0.275) 95 (3.74) 12 (0.47) ø7 (0.275) BO3 ILO OERAED CONROL BO4 ILO OERAED CONROL 2 side levers with detent in any position 2 side levers with detent in any position + neutral position sensor 109 (4.29) 61 (2.40) 109 (4.29) 61 (2.40) ø12 (0.47) 34 o ø12 (0.47) 34 o 323 (12.72) 100 (3.94) 90.5 (3.56) 7 (0.275) 95 (3.74) 41.5 (1.63) 323 (12.72) 131 (5.16) 90.5 (3.56) 7 (0.275) 41.5 (1.63) 12 (0.47) ø7 (0.275) 95 (3.74) 12 (0.47) ø7 (0.275) H 73 / B / 102 / 0308 / E ag. 37

35 RSVB SERIES ECHNICAL DAA Hydraulic ilot Control Valves BO5 ILO OERAED CONROL 2 side levers with detent in rest BO6 ILO OERAED CONROL 2 side levers with detent in rest and clutch in any position 112 (4.41) 112 (4.41) ø12 (0.47) ø12 (0.47) 134 (5.275) 134 (5.275) 38 (1.50) 319 (12.56) 95 (3.74) 38 (1.50) 90 (3.54) 7 (0.275) 319 (12.56) 12 (0.47) 100 (3.94) 90 (3.54) 7 (0.275) ø7 (0.275) 95 (3.74) 12 (0.47) ø7 (0.275) RSVB SERIES YICAL ECHNICAL DAA YICAL RANGE OF LEVER MOVEMEN YICAL OR ARRANGEMEN 171 (6.73) ø45 (1.77) 30 o 30 o 11 (0.43) ø104 (4.09) 7 (0.275) R 3.5 UNLOCKING SR OKE 3 (0.12) BO1, BO2 ONLY ø52 (2.05) U2 U3 U4 ø123 (4.84) YICAL INSALLAION DIMENSIONS 40 (1.575) YICAL HYDRAULIC CIRCUI DIAGRAM 45 o ø108 MAX (4.25) ø104 (4.09) ø100 MIN (3.94) ø85 (3.35) ø6.5 (0.256) U2 U3 U4 ag. 38 H 73 / B / 102 / 0308 / E

36 RSVL SERIES ECHNICAL DAA Hydraulic ilot Control Valves LO1 ILO OERAED CONROL single side lever with return spring LO2 ILO OERAED CONROL single side lever with mechanical detent 54.5 (2.15) 54.5 (2.15) 53 (2.09) 53 (2.09) ø12 (0.47) ø12 (0.47) 12 (0.47) 323 (12.72) 95 (3.74) 90.5 (3.56) 7 (0.275) 41.5 (1.63) 107 (4.21) ø7 (0.275) 95 (3.74) 12 (0.47) LO3 ILO OERAED CONROL single side lever with detent in any position LO4 ILO OERAED CONROL single side lever with detent in any position + neutral position sensor 100 (3.94) 131 (5.16) 323 (12.72) 90.5 (3.56) 7 (0.275) 41.5 (1.63) ø7 (0.275) 54.5 (2.15) 53 (2.09) 54.5 (2.15) 53 (2.09) ø12 (0.47) ø12 (0.47) 323 (12.72) 90.5 (3.56) 95 (3.74) 7 (0.275) 41.5 (1.63) 323 (12.72) 12 (0.47) 90.5 (3.56) 7 (0.275) 41.5 (1.63) ø7 (0.275) 95 (3.74) 12 (0.47) ø7 (0.275) H 73 / B / 102 / 0308 / E ag. 39

37 RSVL SERIES ECHNICAL DAA Hydraulic ilot Control Valves LO5 ILO OERAED CONROL single side lever with detent in rest LO6 ILO OERAED CONROL single side lever with detent in rest and clutch in any position 67 (2.64) 67 (2.64) 56 (2.20) 56 (2.20) ø12 (0.47) ø12 (0.47) 38 (1.50) 95 (3.74) 38 (1.50) 319 (12.56) 90 (3.54) 7 (0.275) 319 (12.56) 100 (3.94) 12 (0.47) 90 (3.54) 7 (0.275) ø7 (0.275) 95 (3.74) 12 (0.47) ø7 (0.275) RSVL SERIES YICAL ECHNICAL DAA YICAL RANGE OF LEVER MOVEMEN YICAL OR ARRANGEMEN 171 (6.73) ø45 (1.77) 30 o 30 o 11 (0.43) ø104 (4.09) 7 (0.275) R 3.5 UNLOCKING SR OKE 3 (0.12) LO1, LO2 ONLY ø52 (2.05) U2 ø123 (4.84) YICAL INSALLAION DIMENSIONS 40 (1.575) YICAL HYDRAULIC CIRCUI DIAGRAM 45 o U2 ø108 MAX (4.25) ø104 (4.09) ø100 MIN (3.94) ø85 (3.35) ø6.5 (0.256) ag. 40 H 73 / B / 102 / 0308 / E

38 RSVB/L SERIES SHULE BLOCK ECHNICAL DAA S1 SHULE BLOCK S3 SHULE BLOCK 38 (1.50) 90 (3.54) 63 (2.48) 90 (3.54) 63 (2.48) 91 (3.58) 1/4" B S (2 pos.) 52 (2.05) U2 U3 40 (1.57) 34 (1.34) 88 (3.46) 91 (3.58) 1/4" B S (2 pos.) 52 (2.05) U2 U5 U3 U4 U6 40 (1.57) 34 (1.34) 88 (3.46) 35 (1.38) 11 (0.43) 45 o 46 (1.81) 45 o 8 (2 pos.) 35 (1.38) 11 (0.43) 46 (1.81) 8 (2 pos.) HYDRAULIC CIRCUI DIAGRAM U2 HYDRAULIC CIRCUI DIAGRAM U2 U3 U4 U3 U2 U5 U2 U3 U6 U4 H 73 / B / 102 / 0308 / E ag. 41

39 HV SERIES HYDRAULIC ILO CONROLS H 73 / B / 102 / 0308 / E ag. 43

40 HV SERIES INRODUCION HYDRAULIC ILO CONROL BENEFIS H V ilot C ontrol Valves are part of the comprehens ive range of our Hydraulics product. he product, with its s ingle lever dual axis control, and supported by an extensive range of control curve characteristics and handle options, makes it suitable for a wide range of both mobile and indus trial applications. Our engineers can offer specialist support to optimis e this product to s uit your application. he product is s upported by a comprehens ive S ales and S ervice facility around the world. Compact and light weight All ports on bottom face for ease of installation Suitable for arm rest of console mounting Compatible with a wide range of product S tylish good looks suit able for modern cabs Operator is insulated from high temperature components roven, simple pressure reducing elements Wide range of low hysteresis, high accuracy, pressure control curves Wide range of electrical options in both standard and multi-functional ergonomic handles Low effort lever control HV SERIES MODEL CODING HV 1 CO1 X XXX X X R eturn spring 0 = S tandard: 1.4 to 2.8 dan 1 = Light: 3.0 to 4.5 dan 2 = Medium: 7.5 to 13.8 dan Gaiter R = Round S = Square Metering curve see CV CHARACERISICS section Handle type W = Without Handle see HANDLES section Basic model type CO1 see page 3 1 = Design Mark HV = Hydraulic ilot Control Example : ordering number : HV 1 C01 W 015 S 1 model number : HV 1 C01 W 015 S 1 / (assigned number) ag. 44 H 73 / B / 102 / 0308 / E

41 HV SERIES ECHNICAL DAA Hydraulic ilot Control Valves CO1 with SQUARE gaiter CO1 with ROUND gaiter VIEW FROM'A' 102 (4.02) VIEW FROM'A' ø131 (5.16) ø100 (3.94) U2 U4 U3 ø125 (4.92) ø52 (2.05) ø52 (2.05) U2 U4 U3 37(1.46) 'B ' Max for 1 service Max for 2 services 21 o 27 o ø39.5 (1.56) 37 (1.46) 'B ' Max for 1 service Max for 2 services 21 o 27 o ø39.5 (1.56) 306 (12.05) 75 (2.95) 231 (9.09) 29.5 (1.16) 306 (12.05) 75 (2.95) 231 (9.09) 29.5 (1.16) 'A' 'A' ø100 (3.94) ø85 (2.95) 45 o MOUNING DE AILS ø6.5 (0.255) ø108 MAX (4.25) ø104 (4.09) ø100 MIN (3.94) ø85 (2.95) 45 o MOUNING DE AILS ø6.5 (0.255) 2/1 1 2/ /1 2/1 YICAL FUNCIONAL DIAGRAM (V IE W FR OM 'B ') U2 U3 U4 YICAL CIRCUI DIAGRAM H 73 / B / 102 / 0308 / E ag. 45

42 RSV SERIES FOO EDALS H 73 / B / 102 / 0308 / E ag. 47

43 RSV SERIES INRODUCION HYDRAULIC ILO CONROL RSV ilot Control Valves are part of the comprehensive range of our Hydraulics product. his product, with its range of foot pedal controls, supported by an extensive range of control curve characteristics and a choice of handle options, makes it s uitable for a wide range of applications. Our engineers can offer specialist support to optimis e this product to s uit your application. he product is s upported by a comprehens ive S ales and S ervice facility around the world. BENEFIS C ompact and light weight orts ideally positioned for ease of installation S imple to mount C ompatible with a wide range of product Operator is insulated from high temperature components roven, simple pressure reducing elements Wide range of low hysteresis, high accuracy, pressure control curves R ange of operator pedal efforts available R ubber boot protection to prevent ingress of airborne contaminant R ubber boot suitable for a wide range of environmental conditions lunger manufactured from non-corrosive steel E nd of stroke limited externally to prevent any damage to internal components Double lip seal option available for increased product life Optimised angular movement of foot pedal RSV SERIES MODE L CODING RSV XX X XXX XX X Return spring 1 = Light: 3.0 to 4.5 dan 2 = Medium: 7.5 to 13.8 dan 3 = Heavy: 10.0 to 19.0 dan lunger Seal and R ubber B oot Options see page 47 SW = standard seal without rubber boot SG = standard seal with type G rubber boot (option not available for RSV03) SK = standard seal with type K rubber boot (option not available for RSV01) LW = double lip longlife seal without rubber boot LK = double lip longlife s eal with rubber boot type K (option not available for RSV01) Metering curve see C V C H A R A C E R I S I C S section edal ype W S V = Without pedal = Flat standard pedal = V shaped pedal (available only for R S V01) Basic model number O 1 = R ocker pedal with 2 pilot s pools 0 2 = win pedal with 2 pilot s pools 0 3 = S ingle pedal with 1 pilot s pool R S V = Hydraulic ilot Valve S eries ag. 48 H 73 / B / 102 / 0308 / E

44 RSV SERIES ECHNICAL DAA Hydraulic ilot Control Valves RSV01S flat standard rocker pedal RSV01V V shaped rocker pedal 20(0.79) 9(0.35) 18 (0.71) U2 40 (1.575) 20(0.79) 9(0.35) 18 (0.71) U (3.15) 160(6.30) 180(7.09) 130(5.12) (3.15) 160(6.30) 180(7.09) 70(2.76) 130(5.12) 157.5(6.20) 31(1.22) 104.5(4.115) 8 200(7.875) 10(0.39) (.315) 55(2.17) 66(2.60) 70(2.76) 31(1.22) 104.5(4.115) 8 (.315) (1.575) 20(0.79) 55(2.17) 66(2.60) 70(2.76) 82(3.23) 260(10.24) 82(3.23) 282(11.10) RSV01W rocker model without pedal 20(0.79) 9(0.35) 18 (0.71) U2 80(3.15) 160(6.30) 40 (1.575) 60(2.36) 52.5(2.07) ypic al Hydraulic Circ uit Diagram for all foot pedals illustrated on this page U2 44.5(1.75) 21.55(0.85) 9.5(0.375) 39.5(1.56) ø12(0.47) ypic al echnic al Data for all foot pedals illustrated on this page 31(1.22) 55(2.17) 8(0.315) 80(3.15) 160(6.30) 104.5(4.115) 24 (0.95) 55(2.17) S ervice ports :,,, U2; 1/4" BS Maximum inlet pressure * : ort - 50 bar Maximum back pressure : ort - 3 bar S upply flow range : from 5 up to 20 litres /minute Maximum Hysteresis : +/- 0.5 bar Fluid : Mineral Oils IS O, HM and HV Contamination class : 16/11 IS O 4406 F luid temperature range : from -20 up to +80 o C * Higher inlet pressures may be possible. Also side porting is available. For both requirements, please consult your Hansa-mp s.r.l. repres entative. H 73 / B / 102 / 0308 / E ag. 49

45 RSV SERIES ECHNICAL DAA Hydraulic ilot Control Valves RSV02S win pedal RSV03S one pilot spool with pedal ø123(4.84) ø104(4.09) ø85(3.35) ø52(2.05) 11(0.43) U2 7(0.28) 3 o 60(2.36) 7 o 14 ' 174(6.85) 79(3.11) 47(1.85) 48(1.89) 25(0.985) U 57(2.24) 30(1.18) 60(2.36) 45(1.77) 46(1.81) 20(0.79) 25(0.985) 45.5 (1.79) 154(6.06) 112.5(4.43) 120(4.73) 63(2.48) 160(6.30) 183(7.20) ø10(0.39) (4 positions) 60(2.36) 222(8.74) Hydraulic Circuit Diagram Hydraulic Circuit Diagram U2 U echnic al Data S ervice ports :,,, U2; 1/4" B S Maximum inlet pressure * : ort - 50 bar Maximum back pressure : ort - 3 bar S upply flow range : from 5 up to 20 litres /minute Maximum Hysteresis : +/- 0.5 bar Fluid : Mineral Oils IS O, HM and HV Contamination class : 16/11 IS O 4406 F luid temperature range : from -20 up to +80 o C echnic al Data S ervice ports :,, U; 1/4" B S Maximum inlet pressure * : ort - 50 bar Maximum back pressure : ort - 3 bar S upply flow range : from 5 up to 20 litres /minute Maximum Hysteresis : +/- 0.5 bar Fluid : Mineral Oils IS O, HM and HV Contamination class : 16/11 IS O 4406 F luid temperature range : from -20 up to +80 o C * Higher inlet pressures may be possible, pleas e cons ult our echnical Department. ag. 50 H 73 / B / 102 / 0308 / E

46 RSV SERIES LUNGER AND BOO YES SW Seal type S / NO Boot (W) SG S eal type S / B oot type G SK Seal type S / Boot type K LW S eal type L / NO B oot (W) LK S eal type L / B oot type K H 73 / B / 102 / 0308 / E ag. 51

47 SUH SERIES ILO SULY UNIS H 73 / B / 102 / 0308 / E ag. 53

48 SUH SERIES INRODUCION ILO SULY UNIS he SUH is a direct acting pressure reducing valve which can be connected to either one or two main circuits via ports 1 and 2. Both ports feed through a s huttle valve to prevent circuit interaction. R educed pres s ure is s upplied to port 1 and 2. A pre-set relief valve is fitted to prevent over pres s ure, and the unit is s upplied with an accumulator connection for emergency power s upply. An s olenoid attachment is available to act as a safety system and to maintain the accumulator charge for a longer period by preventing leakage downstream from the U ports. Als o a vers ion is available with integral filter to protect the output line and hence downs tream components. BENEFIS Compact unit Optional accumulator for peak and emergency power Optional 2 way & 3 way, 12 or 24 V DC solenoid valves for s afety and extended accumulator s torage time Dual ports for maximum ins tallation flexibility ECHNICAL FEAURES Input pressure : Min 8 bar, Max 350 bar Output pressure (nominal) : 30 bar Max pres s ure on drain port : 3 bar R elief valve setting (nominal) : 45 bar Max accumulator pressure : 210 bar (Nitrogen pre-charge 13 bar) F low capacity at ports S : 5 l/min without accumulator : up to 40 l/min with accumulator Hydraulic fluids : IS O HM & HV bio-degradeable fluids F luid temperature range : -20 to +80 o C Fluid viscosity : 2.8 to 380 mm 2 /s ec Maximum filter rating : 25μm (absolute) Description Weight (kg) BASIC SUH VALVE LIR E ACCUMULAOR LIR E ACCUMULAOR LIR E ACCUMULAOR WAY S E LE COR WAY S E LE COR 0.70 SUH SERIES MODE L CODING SUH XXX - XXX X XXX Example: Standard valve set at 30 bar, with 12 Volt s olenoid valve and 0.35 litre accumulator ordering number: S UH 030 A22 L 035 model number: S UH 030 A22 L 035 / (assigned number) Accumulator sizes 000 = No accumulator = 0.35 litre accumulator = 0.75 litre accumulator = 1.50 litre accumulator Accumulator options L = with accumulator W = without accumulator = with provision for accumulator Control options A00 = standard valve A 22 = with 2 way selector 12 V DC solenoid A 24 = with 2 way selector 24 V DC solenoid A 32 = with 3 way selector 12 V DC solenoid A 34 = with 3 way selector 24 V DC solenoid ressure setting 025 = 25 bar 030 = 30 bar 035 = 35 bar S U H = S upply unit - hydraulic = 40 bar = 50 bar ag. 54 H 73 / B / 102 / 0308 / E

49 SUH SERIES ECHNICAL DAA SUH-xxx-A00-W-000 standard valve with no accumulator and no provision for an accumulator 1 1 U (1.52) 53.5(2.11) (5.31) 2 2 U2 90(3.54) 10(.39) 70(2.76) M8X (.55) 17(.67) 25 BAR 45 BAR 82(3.23) 53(2.09) 51(2.01) 19(.75) 1 37(1.46) 1 1 CIRCUI DIAGRAM (1) 35(1.38) 64.5(2.54) SUH-xxx-A standard valve with no accumulator and with provision for an accumulator 1 U (1.52) 53.5(2.11) (5.31) 2 2 U2 90(3.54) 10(.39) 70(2.76) M8X (.55) 17(.67) 25 BAR 45 BAR 82(3.23) 64(2.52) 53(2.09) 51(2.01) 19(.75) 1 37(1.46) 1 1 CIRCUI DIAGRAM (1) 35(1.38) 64.5(2.54) H 73 / B / 102 / 0308 / E ag. 55

50 SUH SERIES ECHNICAL DAA SUH-xxx-A00-L-xxx s tandard valve with accumulator / with no s olenoid 2 2 U2 A B 15 (0.59) 1 1 YICAL CIRCUI DIAGRAM SANDARD VALVE For dimensions see page 3 C Accumulator Capacity A Accumulator Length B Overall Unit Length C Maximum Diameter SUH-xxx-A00-L-035 SUH-xxx-A00-L-075 SUH-xxx-A00-L litres 0.75 litres 1.50 litres 162 (6.38) 200 (7.87) 295 (11.61) 302 (11.89) 340 (13.39) 435 (17.13) 99 (3.90) 115 (4.53) 115 (4.53) SUH-xxx-A22-L-xxx valve with accumulator and 12V DC 2-way s olenoid SUH-xxx-A24-L-xxx valve with accumulator and 24V DC 3-way s olenoid F or dimens ions including accumulators see above 1 1 U2 2 2 SANDARD VALVE F or dimens ions see page 3 F or dimens ions including accumulators see above 1 1 U 2 SANDARD VALVE For dimensions see page (1.46) 11 (0.43) (4.09) 164 (6.46) 60 (2.36) (4.49) 174 (6.85) 48.5 (1.91) 5 (0.20) U 115 (4.53) 60 (2.36) 120 (4.72) 2 2 U2 2 U 1 1 CIRCUI DIAGRAM 1 1 CIRCUI DIAGRAM ag. 56 H 73 / B / 102 / 0308 / E

51 SUH SERIES FILER ECHNICAL DAA SUH w ith inlet line filter 98.8 (3.89) 135 (5.31) 33 (1.30) 48 (1.89) 38.5 (1.52) 60 (2.36) Removal 7.5 (0.30) 5.6 (0.22) 38.5 (1.52) 135 (5.31) 124 (4.88) 122 (4.80) 19 (0.75) 33 (1.30) 153 (6.02) 58 (2.28) 108 (4.25) Filter Unit U 25.5 (1.00) 64.5 (2.54) 100 (3.94) 30 BAR 10 (0.39) 70 (2.76) 45 BAR 25μm F IL E R U CIRCUI DIAGRAM 2 mounting holes M8 x 1.25 x 14.0 deep his vers ion of the S UH has an integral filter fitted to the inlet line of the valve to provide complete protection to both the pilot s upply unit and any downs tream s ervices from contamination. he filter element is rated at 25μm absolute and is replaceable. o model code this unit, add the code /F onto the end of the s tandard model code as shown on page 50. H 73 / B / 102 / 0308 / E ag. 57

52 ILO CONROL VALVES CHARACERISICS H 73 / B / 102 / 0308 / E ag. 59

53 CV CHARACERISICS INRODUCION MEERED CURVES hese characteristics are compatible with HV, HVL, SVL, and the entire RSV range of product. F or optimum control it is important to s elect the correct characteris tic to s uit the application and our echnical Department are always pleased to assist in this process. here is a comprehensive worldwide S ales and S ervice facility around the world. BENEFIS High precision components Low hysteresis Excellent repeatability Wide range of options Suitable for a wide range of product Virtually no service work required Can be engineered to suit your particular application ag. 60 H 73 / B / 102 / 0308 / E

54 ILO CONROL VALVE ME E R ING C UR VE S LINEAR CHARACERISICS WIHOU SE pressure B A plunger stroke C D Output lunger Metering ressure (bar) S troke (mm) Curve Number A B C D Output lunger Metering ressure (bar) S troke (mm) Curve Number A B C D H 73 / B / 102 / 0308 / E ag. 61

55 ILO CONROL VALVE MEERING CUR VES Hydraulic ilot Control Valves LINEAR CHARACERISICS WIH SE pressure B A SORED BY ID NUMBER C plunger stroke RESSURE (BAR) SROKE ( mm ) ID NUMBER A B C D 6 22,5 2 6,5 CR ,2 CR ,7 2 6,3 CR ,3 1,6 7,1 CR008 0,5 4 1,8 8,4 CR009 0,5 6,5 2 8,5 CR ,5 CR ,5 1 8,5 CR012 8,2 24,4 1,8 8,5 CR013 8,2 24,5 1 8,5 CR014 5,8 22 1,8 8,5 CR015 5,8 19 1,8 7,3 CR016 5,8 19 0,9 6,4 CR017 4,9 18,9 1 8,5 CR ,5 1 8,5 CR019 6, ,5 CR ,5 CR ,5 CR ,2 0,9 8,5 CR ,5 2 8,5 CR025 5,03 15,93 1 8,5 CR ,5 8,5 CR027 5,5 24,2 0,9 8,5 CR028 5,8 19 1,6 7,1 CR029 3,4 29,4 1 8,5 CR ,5 CR031 9,8 26 1,8 8,5 CR ,0 1 8,5 CR ,2 6,5 CR038 3,25 15,4 1 8,5 CR ,5 6,5 CR042 6,6 20,7 1 8,5 CR ,7 1,8 8,5 CR ,5 CR045 0,5 11,4 1,8 8,5 CR047 3,2 11,7 1,8 8,5 CR048 4,3 15,2 1 8,5 CR049 D ag. 62 H 73 / B / 102 / 0308 / E

56 ILO CONROL VALVE MEERING CUR VES LINEAR CHARACERISICS WIH SE...continued RESSURE ( BAR ) SROKE ( mm ) ID NUMBER A B C D 6 17,4 1 7,1 CR ,5 CR051 3,2 17,2 1 8,5 CR ,5 CR063 5,9 12,9 1 8,5 CR065 1,5 8,5 1 8,5 CR ,5 CR070 8, ,5 CR073 0,5 18,4 1 8,5 CR ,5 0,9 8,5 CR ,5 CR ,5 1 8,5 CR CR081 5,8 22,4 0,9 8,5 CR ,5 2 8,5 CR084 5,8 22 0,9 8,5 CR ,5 0,9 8,5 CR090 4,5 18 0,9 8,5 CR095 0,8 29 1,4 3,5 CR097 8,4 21,1 3,25 8,5 CR ,5 1,8 7,3 CR099 7,2 15,3 1 8,9 CR100 3, ,5 CR101 3,73 29,23 1 8,5 CR104 5,8 19,8 1 8,5 CR106 4, ,8 8,5 CR107 4, ,5 CR CR109 5,15 19,1 1,2 8,5 CR112 5, ,5 CR ,5 CR116 4,9 17,5 1 8 CR117 8,4 27,9 1,8 8,5 CR120 3,04 21,74 0,9 8,5 CR121 4,3 13,8 1 8,5 CR122 2,76 14,91 1 8,5 CR ,5 CR125 6,7 16,2 1 8,5 CR127 2,8 4,75 1 8,25 CR ,7 0,5 8,5 CR135 7,57 24,63 0,5 8,5 CR136 5,69 17,84 1 8,5 CR137 4,44 30,44 1 8,5 CR138 5, ,9 CR ,7 1 8,5 CR150 H 73 / B / 102 / 0308 / E ag. 63

57 ILO CONROL VALVE MEERING CURVES BROKEN CHARACERISICS WIHOU SE pressure C B A plunger stroke SORED BY ID NUMBER D E F RESSURE ( BAR ) SROKE ( mm ) ID NUMBER A B C D E F CR119 1,5 8 17, CR ,8 6 9,3 CR CR CR CR142 ag. 64 H 73 / B / 102 / 0308 / E

58 ILO CONROL VALVE MEERING CURVES BROKEN CHARACERISICS WIH SE pressure C B A plunger stroke SORED BY ID NUMBER D E F RESSURE ( BAR ) SROKE ( mm ) ID NUMBER A B C D E F 0,2 2,8 8,4 0,5 5,7 8,4 CR102 1, ,5 CR103 1, ,6 5,4 8,4 CR , ,5 8,5 CR ,3 14 1,1 7 8,4 CR118 7, ,8 6 8,5 CR134 8,5 12, ,5 CR144 7, ,5 CR ,5 21,5 1,3 5 8,6 CR ,5 CR ,5 CR ,5 CR174 7, ,7 1,2 5,4 6,5 CR184 7, ,2 1 5,2 8,5 CR161 H 73 / B / 102 / 0308 / E ag. 65

59 OIL SAMLING VALVES H 73 / B / 102 / 0308 / E ag. 67

60 OIL SAMLING VALVES INR ODUCION he Oil Sampling V alve provides a permanently fitted, cos t effective s olution for collecting oil s amples from a pressurised hydraulic system while that system is running under normal conditions, which is a recognis ed method of collecting a representative s ample of oil reflecting the true condition of oil within the s ys tem. It is als o important that the oil is not contaminated either during collection or until it reaches the laboratory. B y using the correct valve model to suit the system pressure to which it will be fitted this contamination free collection can be achieved. OERAION he oil s ampling valve includes an as s embly of a number of grooved discs which form an orifice of known length. B y varying the number of dis cs this orifice length can be controlled such that it can be made suitable for different system pressures and allow samples to be taken for s ys tems of different press ure without the danger created by oil jetting at high velocity. As there are no moving parts, and the oil velocity is low, there is no tendency to create contamination within the unit. All parts are non-magnetic. he unit is s uitable for s ampling oil from s ys tems with pres s ures of up to 420 bar and is s uitable for any type of fluid. he appropriate model must be specified for the system pres s ure. S ample bottles, with a graduated s cale up to 250 ml to IS O-4796, are also available. OIL SAMLING VALVES INSALLAION ag. 68 H 73 / B / 102 / 0308 / E

61 OIL SAMLING VALVES ECHNICAL DAA 10 (0.39) 3/8" B S MODEL AR SYSEM DIMENSION WEIGH NUMB E R NUMB E R R ESSUR E L (gr) (bar) mm (inc hes ) L (see table) 201A-1-1 B (3.88) A-1-2 B (3.84) A-1-4 B (3.90) A-1-6 B (3.96) A-1-8 B (4.02) A-1-10 B (4.07) A-1-12 B (4.13) A-1-14 B (4.19) A-1-16 B (4.25) A-1-18 B (4.31) A-1-20 B (4.37) 533 ighten this nut to 34 Nm Note: he chart shows model numbers designed to be used with mineral oils and emulsion. Models are available to be used with VION seals and phosphate ester fluids; for details please contact our ech. Dpt. LENGH 1 VALVE LENGH 2 VALVE DIS C 2 DIS CS 4 DIS CS 6 DIS CS 8 DIS CS 10 DIS CS VISCOSIY (cst) A AMOSHERIC RESSURE DIS CS 14 DIS CS 16 DIS CS 18 DISCS 20 DIS CS RIMARY RESSURE (bar) RIMARY RESSURE (bar) S ampling flow: 100cc/min with fluid at 30 cs t Maximum temperature: 100 o C H 73 / B / 102 / 0308 / E ag. 69