Fixed Displacement Bent Axis Axial Piston Pumps TPB 70 - TAP 70
|
|
- Ralf Griffith
- 5 years ago
- Views:
Transcription
1 HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001: :2015 ISO 9001:2015 Certificate N 12-Q TIC ISO 14001:2015 Certificate N 12-E TIC Via M. L. King, MODENA (ITALY) Tel: Fax: INTERNET: hansatmp@hansatmp.it THE PRODUCTION LINE OF HANSA-TMP - ISO SAE DIN
2
3 CONTENTS ISO General Information... Ordering Code... Dimensions Dimensions Dimensions Dimensions Dimensions 108 / General Instructions SAE General Information... Ordering Code... Main Data / Dimensions DIN General Information... Ordering Code... Main Data / Dimensions Pag. 3
4 Pag. 4
5 Pag. 5
6 Dimensions ( ) ISO Dimensions ( ) ISO Pag. 6
7 Dimensions TBB 70 ( ) ISO Dimensions ( ) ISO Pag. 7
8 Dimensions (108) ISO Dimensions (130) ISO Pag. 8
9 General instructions Choice of shaft seal Code Temp. Max. housing pressure MPa at rpm Pump ISO C N H V N H V N H V Code according to page, Factors affecting the choice of shaft seal include the hydraulic pump housing pressure and the drainage oil temperature. The drainage oil should have a maximum temperature of 75 C with a Nitrile shaft seal and 90 C with a Viton shaft seal. These temperatures must not be exceeded. The housing pressure must be equal to or greater than the external pressure on the shaft seal. Minimum inlet pressure at suction port with increased speed Operating above the max. pump speed n max requires increased inlet pressure. 2.0 Note that the max. permissible speed n max limit must not be exceeded. Filtering Speed n/nmax Suction pressure bar absolute Cleanliness according to ISO norm 4406, code 16/13. Hydraulic fluids High performance oils meeting ISO specifications such as HM, DIN HLP, or better must be used. A min. viscosity of 10 cst is required to keep the lubrication at a safe level. The ideal viscosity is cst. Pag. 9
10 Recommended line size (di) 38 mm (1½") Suction line 50 mm (2") 64 mm (2½") 75 mm (3") 25 mm (1") Return line 32 mm (1¼") 38 mm (1½") 45 mm (1¾") 12.5 mm (½") Pressure line 19 mm (¾") 25 mm (1") 32 mm (1¼") Flow litres min d i If the suction line is more than 2 m long the internal diameter must be increased by 10 mm for each meter extension. Installation The pump housing should be filled with oil to at least 50% before starting. The drainage line must be at least 1/2 (13 mm) internal diameter and should be connected to topmost drainage outlet. The other end of the line should be connected to the oil tank at a point below the oil level. Pag. 10
11 Pag. 11
12 Pag. 12
13 Pag. 13
14 Pag. 14
15 Pag. 15
16 Pag. 16
17 PRODUCT GUIDE PUMPS Closed Loop (Variable Displacement) cc Open Loop (Fixed Displacement) cc Bent Axis Pumps cc Model Rated Peak Maximum Displacement cm 3 Pressure Pressure speed /n. MPa MPa n/min TPB , Weight kg 83.6, 90.7, The table values can change in function of the configuration. 1
18
19
20 As HANSA-TMP has a very extensive range of products and some products have a variety of applications, the information supplied may often only apply If the catalogue does not supply all the information required, please contact Whilst every reasonable endeavour has been made to ensure accuracy, this publication cannot be considered to represent part of any contract, whether HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, MODENA (ITALY) Tel: Fax: INTERNET: hansatmp@hansatmp.it
Fixed Displacement Bent Axis Axial Piston Motors TMB 700
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001:2015-14001:2015 ISO 9001:2015 Certificate N 12-Q-0200545-TIC ISO 14001:2015 Certificate N 12-E-0200545-TIC
More informationTPF 60 (36,16 49,94 cm³/rev.)
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationTMF 500. Fixed Displacement Axial Piston Motor for Open and Closed Loop System MANUFACTURING THE PRODUCTION LINE OF HANSA-TMP
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES MANUFACTURING THE PRODUCTION LINE OF HANSA-TMP Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 /
More informationTMF 600 ( cm³/rev.)
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 852 / 0815 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 114 / 0814 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationVariable Displacement Open Loop Circuit Axial Piston Pumps AR Series
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET: http://www.hansatmp.it E-MAIL:
More informationTPV 4000 (EX 28-41) Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE TRANSMISSION LINE OF HANSA-TMP HT 16 / M / 280 / 1008 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump MANUFACTURING THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 403 / 1110 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 501 / 1009 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HY-TRANS THE PRODUCTION LINE OF HANSA-TMP Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationVariable Displacement Open Loop Circuit Axial Piston Pumps. V Series
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET: http://www.hansatmp.it E-MAIL:
More informationMOTOR SCM M2
MOTOR SCM 025 108 M2 Sunfab SCM M2 is a range of robust axial piston motors especially suitable for winch-, slewing-, wheeland track drives. Sunfab SCM M2 is of the bent-axis type with spherical pistons.
More informationSCM M2. Other advantages:
Sunfab s SCM 025-108 M2 is a range of robust axial piston motors with cartridge flange especially suitable for winch-, slewing-, wheel- and track drives. SCM 025-108 M2 is of the bent-axis type with spherical
More informationMOTOR SCM ISO
MOTOR SCM 012-130 ISO SCM 012-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 012-130 ISO is of the bent-axis type with spherical pistons. The design results
More informationTPV 1000 (Ex 6-18) Variable Displacement Closed Loop System Axial Piston Pump HY-TRANS THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 109 / 1008 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HY-TRANS THE PRODUCTION LINE OF HANSA-TMP Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationSCM ISO. SCM ISO is a range of robust axial piston motors especially suitable for mobile hydraulics.
SCM 010-130 ISO is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 ISO is of the bent-axis type with spherical pistons. The design results in a compact motor
More informationHYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HT 12 / A / 551 / 0911 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HT 12 / A / 551 / 0911 / E Speed-up and Splitter Gearboxes Contents General Information 4-5 Speed-up Gearboxes Series 60000-10 kw
More informationSCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.
Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 851 / 0813 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES THE PRODUCTION LINE OF HANSA-TMP Variable Displacement Closed Loop System CONTENTS General Information... Order Code... Manual Control
More informationISO Certificate N 12-E TIC. ISO 9001 Certificate N 12-Q TIC
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Certificate N 12-Q-0200545-TIC ISO 14001 Certificate N 12-E-0200545-TIC Via M. L. King,
More informationSCM DIN. Other advantages:
SCM 012-130 DIN SCM 012-130 DIN is a series of axial piston motors particularly suitable for mobile hydraulics. SCM 012130 DIN is of the bent-axis type with spherical pistons. Other advantages: The design
More informationSlewing Rings HT 2100 / A / 102 / 0609 / E HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES
YDRAULIC COMPONENTS YDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 x: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationSCM SAE. Other advantages: Sunfab s SCM SAE is a range of robust axial piston motors especially suitable for mobile hydraulics.
Sunfab s SCM 010-130 SAE is a range of robust axial piston motors especially suitable for mobile hydraulics. SCM 010-130 SAE is of the bent-axis type with spherical pistons. The design results in a compact
More informationHYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES HT 12 / A / 452 / 1212 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Electromagnetic Clutches Contents General Information... 4-5 Electromagnetic Clutches - 3 danm Series 30900-1 30900-2... Series 30900-1N
More informationTPV 1200 BTB. Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 160 / 0516 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationTPV 1200 BTB. Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 154 / 0413 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified ISO 9001 and 14001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 TERNET:
More informationHy-Trans Product Guide
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationHigh-Pressure Fixed Displacement Radial Piston Pumps PR Series
HYDRULIC COMONENTS HYDROSTTIC TRNSMISSIONS GERBOXES - CCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODEN (ITLY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET:
More informationBrochure Hydraulic Pumps, Hydraulic Parts
www.hidrocel.com.tr 2013 Brochure Hydraulic s, Hydraulic Parts Product Group Bent Axis s Piston s PBA s 2PBA s PBX s Gear s PA s PH s Power Take Off HDP s PTO Adapter, Valve, Cardan Shaft www.hidrocel.com.tr
More informationDual Axis Hydraulic Joystick Series JH4
Dual Axis Hydraulic Joystick Series JH4 03.JH4-0911 Index of content: Description & technical data: Page 3 Hydraulic circuit diagrams (joysticks): Page 4 Typical hydraulic circuit diagrams (system): Page
More informationOrdering Code of 2PBA Pumps
Ordering Code of 2PBA Pumps Pump Code 3 Displacement ( cm ) Direction of Version Sealing Inlet Fittings 2PBA 18 L S N A A Suction Fittings Included N Nitrile V Viton S Special Version C Classic Version
More informationTPVT 1200 BTB. Variable Displacement Axial Piston Pumps CONTENTS. General Information. Installation Instructions. Technical Specifications 6-7
CONTENTS General Information Installation Instructions Technical Specifications Tandem Pump Installation Drawings Hydraulic Diagrams Rear Pump Mounting Flanges Mounting Shaft and Shaft Details Control
More informationGEAR PUMPS DIMENSIONAL DETAILS
DIMENSIONAL DETAILS OUTLET INLET TYPE DISPLACEMENT CM 3 /REV FLOW AT 1500 REV/MIN MAX. WORKING PRESSURE MAX. SPEED DIMENSIONS MM P1 P2 P3 RPM L M D2 1.4 2.0 270 290 310 6000 40 79 D3 2.1 2.9 270 290 310
More informationTPV Variable Displacement Axial Piston Pumps CONTENTS. General Information. Installation Instructions. Technical Specifications 6-7
CONTENTS General Information Installation Instructions Technical Specifications Single Pump Installation Drawing Tandem Pump Installation Drawing Mounting Flanges and Shaft Details Rear Pump Mounting Flanges
More informationHDP Series. Hydraulic Gear Pumps. high performance, custom design, low noise emission, high efficiency...
HDP Series Hydraulic Gear s high performance, custom design, low noise emission, high efficiency... www.hidrocel.com.tr 1 Contents Design of HDP s Range and characteristics HDP 3/61 ISO HDP 3/61 UNI HDP
More informationSeries
Series 1600 01.1600-002 GEAR PUMPS OPERATING PARAMETERS Maximum outlet pressure: Inlet pressure: Speed range: See on the following pages See below* See on the following pages Fluid temperature: Minimum
More informationK3VL. Variable Displacement Open Loop System Axial Piston Pump HT 16 / F / 419 / 0617 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415
More informationHPC. Dual Displacement Staffa Radial Piston Motors HT 18 / C / 150 / 1007 / E HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M.L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More information5.1 MEDIUM HEAVY DUTY SERIES SIZE 2
.1 MEDIUM HEAVY DUTY SERIES SIZE 2 CONTENTS PGI100 Ordering Code.1.1 Medium Heavy Duty Series Technical Information.1.2 Specifications.1.3 Hydraulic fluids.1.4 Viscosity range.1. Temperature range.1.6
More informationTECHNICAL CATALOGUE FD/FDM FDM
l. ORS TECHNICAL FLOW DIVIDERS DATA FD/FDM MODEL SERIES TECHNICAL CATALOGUE FD FD bar FDM bar FDM INDEX GENERAL INFORMATION rpm - - - 950 - - - - - 950 - - - - - 950 - - - - - 0 - - - - - 0 - - - - - 750
More information2PBA Pumps have the following advantages ;
2PBA Bent Axis Piston Pump 2PBA Pumps have the following advantages ; Compact Design, Economical Conception, High Power Density, High Overall Efficiency, High Rotating Speeds, High Output Pressure, 35
More informationTHE PRODUCTION LINE OF PONAR WADOWICE
PONAR Wadowice S.A. ul. Wojska Polskiego 29 34-100 Wadowice Tel.: +48 33 488 21 00 Fax: +48 33 488 21 03 E-mail: ponar@ponar-wadowice.pl Web: www.ponar-wadowice.pl THE PRODUCTION LINE OF PONAR WADOWICE
More informationOutput flow In l/min at 1500 min
Introduction With thru drive For single and multiple pumps Swash plate type for open circuit 1. New type of swash plate and large servo piston with strong bias spring achieves fast response, reduce the
More informationK3VL. Variable Displacement Open Loop System Axial Piston Pump HT 16 / F / 419 / 0617 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Certified Company ISO 91-141 ISO 91 Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 59 415 711 Fax: +39 59 415 729 / 59 415 73 INTERNET:
More informationAxial Piston Pump Series PV Design 45 Variable Displacement. Catalogue HY /UK February 2007
Design 45 Variable Displacement February 2007 Introduction With thru drive for single and multiple pumps Swash plate type for open circuit Technical Features Low noise level Fast response (eg. PV046: upstroke
More informationHigh Torque Geared Motors GB
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationFixed Displacement Pump A4FO Series 10 Axial Piston Unit, Swashplate Design
Fixed Displacement Pump A4FO Series 10 Axial Piston Unit, Swashplate Design Sizes 71 0 Nominal pressure 3 bar Peak pressure 400 bar RE 91455/01.94 RE 91455/01.94 Replaces 07.88 Other fixed displacement
More informationIPCA Medium-pressure Internal Gear Pumps Technical Data Sheet
IPCA Medium-pressure Internal Gear Pumps Technical Data Sheet Design and Function 1 7 6 5 9 2 6 5 7 8 2 1 4a 4b 3 1 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing
More information5.2 MEDIUM HEAVY DUTY SERIES SIZE 3
.2 MEDIUM HEAVY DUTY SERIES SIZE 3 CONTENTS PGI101 Ordering Code.2.1 Medium Heavy Duty Series Technical Information.2.2 Specifications.2.3 Hydraulic fluids.2.4 Viscosity range.2. Temperature range.2.6
More informationPetrone Oleodinamica s.r.l.
Petrone Oleodinamica s.r.l. The Company was set up by Vito Petrone in Gravina in Puglia in 1953 as a workshop to repair farming and industrial vehicles. In 1968, the Company began to develop an interest
More informationB e n t a x i s hydraulic motors. MSeries
B e n t a x i s hydraulic motors MSeries Contents Definition and main applications of hydraulic motors, advantages of HYDRO LEDUC motors.............. 1 Operating conditions of motors... 2 Determining
More informationHigh Pressure Internal Gear Pumps Series QX
High Pressure Internal Gear Pumps Series QX motion and progress 1 / 32 Classification: 410.10..00 Reference: -P -000021 -E -06 / 05.05 Contents 1 General 1.1 Product description 3 1.2 Advantages 3 2 Technical
More informationxxx displacement pumps TXV for trucks
Variable xxx xxx displacement pumps TXV for trucks 1 sommaire why use a variable displacement pump?... 3 your hydraulic equipment.................. 4 load-sensing.... 5 variable displacement... 6 TXV 40
More informationEngineering Product & System Guide
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES Via M. L. King, 6-41122 MODENA (ITALY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730 INTERNET: http://www.hansatmp.it E-MAIL:
More informationHydraulic Pump Series F1plus Fixed Displacement
Fixed Displacement Catalog 9129 8218-02 February 1999, GB Content General information, design 3 Specifications 4 Pump cross section 4 Pump and line selection 5 Ordering code 6 Standard versions 6 Installation
More informationvariable displacement DELTA SAE Serie m i
variable displacement pumps DELTA SAE Serie m i Contents xxx Range and characteristics... 1 Dimensions... 2 Performance.... 5 Control devices.... 4 to 8 Under development Delta pump with constant torque
More informationVariable displacement axial piston pumps
Variable displacement axial piston pumps SVP series GENERAL INFORMATIONS Variable displacement axial piston pump swash plate design for open circuit-flow sharing control valve. The pump has been designed
More informationPLP Pump (up to 16 cm 3 /r max. 120 bar) PHV Pump (up to 32 cm 3 /r max. 250 bar) PVS Pump (up to 100 cm 3 /r max. 100 bar)
General Catalogue MODEL PLP Pump (up to 16 cm 3 /r max. 120 bar) PHV Pump (up to 32 cm 3 /r max. 250 bar) PVS Pump (up to 100 cm 3 /r max. 100 bar) PSP Pump (up to 100 cm 3 /r max. 160 bar) PSPK Pump (up
More information» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries
HYDRAULIC HW APPLICATION» Conveyors» Feeding mechanism of robots and manipulators» Metal working machines» Textile machines» Machines for agriculture» Food industries» Grass cutting machinery etc. CONTENTS
More information6.3 SIZE 2. Ordering Code External Gear Pump
6.3 SIZE 2 CONTENTS PGE12 Ordering Code 6.3.1 External Gear Pump Technical Information 6.3.2 Specifications 6.3.3 Hydraulic fluids 6.3.4 Viscosity range 6.3.5 Temperature range 6.3.6 Seals 6.3.7 Filtration
More informationPump SCP / SCPT 090,130 DIN, SAE
3118 GB Pump SCP 012-108 / SCPT 090,130 DIN, SAE Sunfab SCP and SCPT are range of piston pumps of a bent axis design with fixed displacement for demanding mobile hydraulics. It covers the whole displacement
More informationFeed Pumps VP / VPB / VPBM
Feed Pumps VP / VPB / VPBM Symbol General The feed pumps from the VP series are low-noise, single-stroke vane pumps with constant flow rate. Using a damped bell housing (PT) enables noise levels to be
More informationIPVP High-pressure Internal Gear Pumps for Variable Speed Drives
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Design and Function 7 6 5 9 2 5 6 7 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing
More informationTPV Variable Displacement Closed Loop System Axial Piston Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 855 / 0817 / E
HYDRULIC COMPONENTS HYDROSTTIC TRNSMISSIONS GERBOXES - CCESSORIES Certified Company ISO 9001-14001 ISO 9001 Via M. L. King, 6-41122 MODEN (ITLY) Tel: +39 059 415 711 Fax: +39 059 415 729 / 059 415 730
More informationHydraulic pumps, motors and accessories. The solution for all your hydraulic needs
Hydraulic pumps, motors and accessories The solution for all your hydraulic needs Content Sunfab history 3 Development 4 Production 5 Environment and Quality Assurance 7 Product overview 8 Pumps fixed
More informationVINCKE HYDRAULIC PUMPS
: VNK BA10VS 21 Variable displacement axial piston pump of swashplate design for hydraulic open circuit systems. Flow is proportional to drive speed and displacement. It can be infinitely varied by adjustment
More informationPVE /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT SERIES 30 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS
14 110/117 ED PVE VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTMENT OPERATING PRINCIPLE The PVE pumps are variable displacement vane pumps with direct pressure regulator. The pump group
More informationExternal gear motor High Performance AZMB
External gear motor High Performance AZMB RE 14027 Edition: 0.201 Platform B Fixed displacement Sizes 2.5 to 7.1 Continuous pressure up to 220 bar Intermittent pressure up to 2 bar Features Consistently
More informationIPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet
IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet Design and Function 7 6 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b
More informationB e n t a x i s hydraulic motors MXP. Series
e n t a x i s hydraulic motors MXP Series Contents Definition and main applications of hydraulic motors, advantages of HYDRO LEDUC motors.............. 1 Operating conditions of motors... 2 Determining
More informationGMP-Type. Key Features: Integrated Motor-Pump Units
Integrated Motor-Pump Units GMP-Type Key Features: Direct coupling between motor and pump Rotation: Right (viewed from shaft end) Electric motor mounting type: special B3-B14 (IEC 34-7) Rated Voltage:
More informationTruck Hydraulics. Series F1, F2, T1 Fixed Displacement Pumps
Series F1, F2, T1 Fixed Displacement Pumps aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Contents Hydraulic Pumps,
More informationVariable displacement axial piston pumps,
LVP 04 T E Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar
More informationVariable displacement axial piston pumps,
Variable displacement axial piston pumps, Edition: 04/04.2000 Replaces: 04/10.99 DISPLACEMENTS From To PRESSURE Max. continuous Max. intermittent Max. peak 29 cm 3 /rev 73 cm 3 /rev 280 bar 315 bar 350
More informationPVD /117 ED VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE
14 100/117 ED PVD VARIABLE DISPLACEMENT VANE PUMPS WITH DIRECT PRESSURE ADJUSTER OPERATING PRINCIPLE The PVD pumps are variable displacement vane pumps with mechanical pressure compensator. The pressure
More informationAxial Piston Fixed Displacement Pump KFA
Industrial Hydraulics Electric Drives and Controls Linear Motion and Assembly Technologies Pneumatics Service Automation Mobile Hydraulics Axial Piston Fixed Displacement Pump KFA RE 91 501/06.03 1/12
More information1.5DRE. Aluminium gear flow dividers. Technical Catalogue E IM00
1.5DRE Aluminium gear flow dividers Technical Catalogue E0.109.0416.02.00-IM00 GEAR FLOW DIVIDERS E SERIES General Features GEAR DIVIDERS A flow divider is composed by two or more modular elements (stages)
More informationOFFLINE SERIES GLOBAL STANDARD COOLER
OFFLINE SERIES GLOBAL STANDARD COOLER OIL-TO-AIR COOLING SYSTEMS WITH AC-MOTOR AND PUMP Product information AKG-Line is a standard line of products from the market leader in high performance aluminium
More informationGear Pumps / Motors. Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs
Gear Pumps / Motors Series PGP / PGM Fixed Displacement Pumps, Cast-Iron and Aluminium Designs Contents Contents Page PGP/PGM500 Characteristics... 3 PGP502 Ordering... 4 PGP502 Performance curves... 5
More informationRV1P /118 ED VARIABLE DISPLACEMENT VANE PUMPS SERIES 10 OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS HYDRAULIC SYMBOL
14 201/118 ED RV1P VARIABLE DISPLACEMENT VANE PUMPS OPERATING PRINCIPLE TECHNICAL SPECIFICATIONS (measured with mineral oil with viscosity of 46 cst at 40 C) RV1P are variable displacement vane pumps with
More informationB e n t a x i s hydraulic motors MXR. Series
e n t a x i s hydraulic motors MXR Series Contents Definition and main applications of hydraulic motors, advantages of HYDRO LEDUC motors.............. 1 Operating conditions of motors... 2 Determining
More informationInternal Gear Unit. for motor/pump service Series QXM. Reference: 100-P EN-07 1/16. Issue:
Internal Gear Unit for motor/pump service Series QXM Reference: -P-63-EN-7 Issue: 8.215 1/16 Contents Page 1 General... 3 1.1 Product description... 3 1.2 Advantages... 3 1.3 Application... 3 1.4 ATEX
More informationRA / Internal Gear Pump Model GP3, Series 3X Fixed Displacement. Typical application:
Sizes 20 to 32 Internal Gear Pump Model GP3, Series 3X Fixed Displacement up to 5076 PSI 1.25 to 1.98 in 3 (350 bar) (20.6 to 32.5 cm 3 ) RA 10 234/07.97 Characteristics: Peak pressure of up to 5.076 PSI
More informationInstallation and commissioning of Settima screw pumps. Type GR** SMT** 3-screw screw pumps. a. Medium:
Settima screw a. Medium: HL oil conforming to DIN 51524 Parts 2 and 3 Special media such as: HFA min 5% oil HFB min 40% oil HFC max. 35-55% water HFDR high-viscosity lubricants SKYDROL, MIL-H may also
More informationFEATURES. ROTARY POWER has over 30 years experience in the design and development of high quality Hydraulic equipment.
XL R A D I A L P I S T O N M O T O R S X L R A D I A L P I S FEATURES ROTARY POWER has over 3 years experience in the design and development of high quality Hydraulic equipment. Our current product range
More informationHYDRAULICS VINCKE HYDRAULIC PUMPS
VINCKE HYDRAULIC PUMPS TECH-VHP200.1 index 3 link to your page / link a su página Gear pumps Introduction 3 Group 0 3 Group 1 3 Group 2 3 Group 3 4 6 7 12 18 Variable displacement pumps 21 Hand pumps 3
More informationGenuine Metaris MA10VO/VSO Technical Catalog. Variable Displacement Piston Pump - A10V Series 31 & 52
Genuine Metaris MA10VO/VSO Technical Catalog www.metaris.com Contents General Series MA10VO/VSO Series 31 4 Page Features 4 Technical Data 5 Performance Information 6 Model Code Breakdown 9 Fluid Info
More informationAxial Piston Variable Double Pump A8VO
Axial Piston Variable Double Pump A8VO RE 93010/03.09 1/40 Replaces: 11.07 Data sheet Series 61 / 63 Sizes 55...200 Nominal pressure 350 bar Peak pressure 400 bar for open circuit Contents Ordering Code
More informationAXIAL PISTON HYDRAULIC MOTOR HM
AXIAL PISTON HYDRAULIC MOTOR HM AXIAL PISTON HYDRAULICS MOTORS HM Function and description Hydraulic motors HM are axial piston units of bent axis type. They have fixed displacement and are designed for
More information1.3 HIGH PRESSURE SERIES
1.3 HIGH PRESSURE SERIES content Ordering Code 1.3.1 High Pressure Series Technical Information 1.3.2 Specifications 1.3.3 Hydraulic Fluids 1.3.4 Viscosity Range 1.3.5 Temperature Range 1.3.6 Seals 1.3.7
More informationIndustrial Components. Internal gear pumps DHPH2, DHPH3, DHPH5, DHPH6
Industrial Components Internal gear pumps DHPH2, DHPH3, DHPH5, DHPH6 Internal gear pump Type DHPH2 high pressure pump with constant displacement volume Characteristics Internal gear pump with axial and
More informationRE 91808/ AA4VSE Plug-in dual displacement motor. High pressure range. Series 10 Axial piston swashplate design, SAE model
AA4VSE Plug-in dual displacement motor Series Axial piston swashplate design, SAE model RE 91808/09.90 RE 91808/09.90 Brueninghaus Hydromatik Size 250 Nominal pressure 350 bar Peak pressure 400 bar High
More informationBent Axis Piston Motor, Fixed, Bi-directional Series: MFBP...1
Features 40 bent axis piston motor for high power and small overall dimensions Bi-directional rotation Rotation speed up to 8800 rpm Torque up to 840 Nm ( 619 ft-lbs) Side or rear port locations available
More informationFixed Displacement Pump A2FO
RE 91401/01.97 Brueninghaus Hydromatik eries 6, for open circuits Axial tapered piston - bent axis design izes 5...1000 Nom. Pressure up to 400 bar Peak Pressure up to 4 bar RE 91401/01.97 replaces 11.95
More informationIPVS High-pressure Internal Gear Pumps Technical Data Sheet
IPVS High-pressure Internal Gear Pumps Technical Data Sheet Functional Drawing 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing segment 5 Axial
More informationInstruction manual. Installation requirements. Power Take-Off. Pump mounting: Spline shaft DIN 5462 / ISO 14. Mounting flange ISO 7653-D.
GB PUMP SCPD 76/76 DIN Instruction manual Thank you for choosing Sunfab You have chosen SCPD 76/76, a dual flow pump with the highest displacement-to-size-ratio on the market. It can effectively be directly
More informationAXIAL PISTON PUMPS SHPV SECTIONAL VIEW
AXIAL PISTON PUMPS SHPV SECTIONAL VIEW 2 AXIAL PISTON PUMPS SHPV SYSTEM CIRCUIT PUMP AND MOTOR CIRCUIT working loop (high pressure) working loop (low pressure) control fluid suction line case drain fluid
More informationTECHNICAL UNION
Bent Axis Pump This hydraulic pump is a Bent Axist type pump, with fixed displacement, developed under the design of spherical head pistons. This design is extremely efficient, as well as high performance.
More informationIn line high pressure filters. HF 725 series
In line high pressure filters HF 725 series THE IMPORTANCE OF AN EFFICIENT FILTRATION The main cause of anomalies in hydraulic systems has to be attributed to the presence of contaminants in the fluid.
More informationHydraulic piston PA PAC PAD. Series
Hydraulic piston pumps PA PAC PAD Series Contents Design of.... 1 Range and characteristics... 2 Characteristics and dimensions... 3 Performance.... 4-5 Accessories.... 6 Shaft sealing... 7 New models
More information