Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN For a complete distributor & dealer list go to

Transcription

1 Illustrated Parts & Packing List 815 Rice Lake Street, Owatonna, MN For a complete distributor & dealer list go to GX18-Hagie Orbit-Air Applicator Hydraulic Raven Monitor Controlled 80 Cu. Ft. Hopper w/18 (2-1/2 ) Openings w/ Black Metering Wheels in Place & Extra Red Metering Wheels w/ 15 GPM Parker Hydraulic Fan Motor Split Shaft, Two Clutch, For 1-1/2 I.D. Tubing (All Parts & Hardware in Place Unless Otherwise Specified) (Black metering wheels for granular products & small seeds such as alfalfa, canola, etc.) (Red metering wheels for fertilizer & lager seeds such as oats, wheat, barley, etc.) H... Mount Base 80/100 Hagie Use: 16 Carriage Bolt (3/8 x 1) (C ) 16 Whiz Flange Nut (3/8) (C ) H... Hopper, 80 Cu. Ft. (Painted Hagie Grey) Use: 6 Sight Window ( ) 12 Rail, Large ( ) 12 Rail, Small ( ) 60 Pop Rivet (3/16 x 3/8) (C ) 2 Decal, Caution Moving Parts (N ) 1 Decal, Important Metering Wheels (N ) 2 Decal, Important Transport (N ) 1 Decal, Caution Black on Yellow (N ) H... Roof, 50/80 Cu. Ft. (Painted Hagie Grey) Use: 30 Whiz Flange Bolt (5/16 x 1) (C ) 30 Whiz Flange Nut (5/16) (C ) H... Cover (For 80/100 Cu Ft) (Painted Hagie Grey) 1... M Rubber Latch w/keeper Use: 4 Pop Rivet (3/16 x 1/4) (C ) Inner Hinge (For Cover) Use: 2 Hex Bolt (3/8 x 3/4) (C ) 4 Wrought Washer (3/8) (C ) 4 Jam Nut, Nylon Lock (3/8) (C ) H... Outer Hinge (For Cover) (Painted Hagie Grey) Use: 2 Hex Bolt (3/8 x 1) (C ) 4 Wrought Washer (3/8) (C ) 4 Jam Nut, Nylon Lock (3/8) (C ) H... Support Rod, Cover Hinge (For 80/100 Cu Ft) (Painted Hagie Grey) Use: 4 Whiz Flange Nut (5/8) (C ) Page 1 of 16

2 Shaft, Gear & Driven (32-3/4 x 5/8 Round) Plastic Bearing (For 5/8 Shaft) Flangette, Bearing (For Plastic Bearing ) Use: 6 Carriage Bolt (1/4 x 5/8) (C ) 2 Carriage Bolt (1/4 x 1) (C ) 8 Whiz Flange Nut (1/4) (C ) Chain Sprocket 21-Tooth (5/8 Bore) Use: 2 Cotter Pin (3/16 x 1-1/4) (C ) Sprocket, 24-Tooth (5/8 Bore x 1-3/8 Hub) Use: 2 Cotter Pin (3/16 x 1-1/4) (C ) Shaft (71-3/4 x 1-inch) Use: 2 SAE Washer (1-inch) (C ) 2... D Bearing (For 1-inch Shaft) Use: 4 Hex Bolt (5/16 x 3/4) (C ) 4 Lock Washer (5/16) (C ) 4 Hex Nut (5/16) (C ) Spacer, Clutch (1-1/4O.D. x 7/8 Long) Chain Sprocket 32-Tooth (One Bolted To Each Clutch) Use: 8 Hex Bolt (1/4 x 3/4) (C ) 8 Whiz Flange Nut (1/4) (C ) Electric Clutch, w/35-tooth Sprocket Welded in Place Use: 1 Clutch Washer ( ) 1 Hex Bolt (5/16 x 3/4) (C ) 1 Lock Washer (5/16) (C ) 1 Hex Bolt (3/8 x 2-1/2) (C ) 2 Whiz Flange Nut (3/8) (C ) 1... L Electric Clutch Use: 1 Clutch Washer ( ) 1 Hex Bolt (5/16 x 3/4) (C ) 1 Lock Washer (5/16) (C ) 1 Hex Bolt (3/8 x 2-1/2) (C ) 2 Whiz Flange Nut (3/8) (C ) Clear Windshield (For 50/80/100 Cu Ft Hoppers) Use: 9 Hex Bolt (1/4 x 1/2) (C ) 9 Wrought Washer (5/16) (C ) 9 Whiz Flange Nut (1/4) (C ) H... Air Chamber, 18-Outlet (For 80/100) (Painted Hagie Grey) Use: 1 Plate, Air Chamber ( ) 2 Hex Bolt (1/2 x 5-1/2) (C ) 2 Wrought Washer (1/2) (C ) 2 Lock Washer (1/2) (C ) 2 Hex Nut (1/2) (C ) 2 Hex Bolt (3/8 x 1) (C ) 2 Whiz Flange Nut (3/8) (C ) 2... M Rubber Plug (2-inch For Air Chamber) M Gasket Mixing Chamber (For 2-inch Mixing Chamber) Mixing Chamber For 1-1/2-inch I.D. Tubing Use: 36 Hex Head TC Screw (5/16 x 3/4) (C ) Page 2 of 16

3 Gasket Potting Box Air Pressure Switch Use: 2 Pan Head TC Screw (#8 x 1/2) (C ) 1 Air Tag (66Air) 1 Cable Tie (3/16 x 8) (L ) 1... L Potting Box Use: 2 Phillips Pan Head TC Screw (#8-32 x 1/2) (C ) Clean-Out Chute (5-inch) Use: 1 Wing Nut (5/16) (C ) 1 Wrought Washer (5/16) (C ) 1 Decal, Caution Plug (N ) 2... M Rubber Plug (4-inch For Hopper) Angle Clamp, Tubing (For 50/80/100 Cu Ft Hoppers, Imp Mount) Use: 4 Foam Clamp Strip (12.00 Long) ( ) 3 Hex Bolt (3/8 x 1) (C ) ( ) 3 Lock Washer (3/8) (C ) 3 Wrought Washer (3/8) (C ) Bar Clamp, Plastic Tubing Use: 4 Foam Clamp Strip (12.00 Long) 6 Hex Bolt (5/16 x 2-3/4) (C ) 6 Lock Nut, Nylon (5/16) (C ) LH... Support Bracket, Left (Painted Hagie Grey) Use: 2 Carriage Bolt (3/8 x 3/4) (C ) 2 Whiz Flange Nut (3/8) (C ) RH... Support Bracket, Right (Painted Hagie Grey) Use: 2 Carriage Bolt (3/8 x 3/4) (C ) 2 Whiz Flange Nut (3/8) (C ) H... Platform (For 80/100 Cu Ft Hopper) (Painted Hagie Grey) Use: 3 Grip Tape (3 x 71 Long) ( ) 2 Carriage Bolt (3/8 x 3/4) (C ) 2 Whiz Flange Nut (3/8) (C ) Support Angle, Platform (For 50/80/100 Cu Ft) (67-1/2 Long) Use: 4 Carriage Bolt (5/16 x 3/4) (C ) 4 Whiz Flange Nut (5/16) (C ) H... Railing, Platform (For 80/100 Cu. Ft.) (Painted Hagie Grey) Use: 3 Hex Bolt (3/8 x 1) (C ) 3 Whiz Flange Nut (3/8) (C ) H... End Rail, Top (Painted Hagie Grey) Use: 1 U-Bolt (1/4) ( ) 2 Whiz Flange Nut (1/4) (C ) 1 Hex Bolt (5/16 x 3/4) (C ) 1 Whiz Flange Nut (5/16) (C ) H... End Rail, Bottom (Painted Hagie Grey) Use: 1 U-Bolt (1/4) ( ) 2 Whiz Flange Nut (1/4) (C ) Screens, (For 50/80/100 Cu Ft Hoppers) Page 3 of 16

4 Sensors & Wire Extensions Sensor Wire Extension SHAFT1... Shaft Tag 1 Use: 1 Cable Tie (3/16 x 8) (L ) SHAFT2... Shaft Tag 2 Use: 1 Cable Tie (3/16 x 8) (L ) Wire Assembly, Clutch Extension Wire CLUTCH1... Clutch Tag 1 Use: 1 Cable Tie (3/16 x 8) (L ) CLUTCH2... Clutch Tag 2 Use: 1 Cable Tie (3/16 x 8) (L ) 2... L Shaft Sensor Kit (Sensor Only Replacement Part Number L ) Mounting Bracket, Shaft Sensor (Mounts to Flangetts ) Hydraulic Blower CP15H-H... Hydraulic Blower, 6 Crary, 15 GPM Parker Motor, (No Hoses) H... Blower Mount (6 Crary Fan) Parker Motor (Painted Hagie Grey) Use: 1 Decal, Warning Rotating (N ) 1 Decal, Important Hydraulic Motor (N ) 1 Decal, Caution Black on Yellow (N ) 1 Decal, Tag Important Caution (N ) 4 Hex Bolt (3/8 x 1-1/2) (C ) 4 Lock Washer (3/8) (C ) 8 Wrought Washer (3/8) (C ) 4 Hex Nut (3/8) (C ) 1... L Fan Assembly (6 Crary) (Front & Rear Housing, Impeller, screen & hardware) Use: 1 Bushing JA Bore (20 mm) (L ) 4 Low Head Socket Cap Screw (1/2-13 x 3/4) (C ) 1... K Hydraulic Motor, Parker F1 (15 GPM) Use: 2 Adaptor Fitting (K ) 2 Hex Bolt (1/2 x 1-1/4) (C ) 2 Lock Washer (1/2) (C ) Page 4 of 16

5 Hydraulic Drive Components 1... K Hydraulic Motor A Series # Use: 4 Hex Bolts (3/8 x 3/4) (C ) 4 Lock Washer (3/8) (C ) Regulator Block Use: 4 Socket Head Cap Screw (5/16 x 2) (C ) 1... L08-SV Solenoid Valve Use: 2 Terminal, 14-16ga, Male, Blue (L ) Plate, Motor Mount Use: 2 Carriage Bolt (3/8 x 1-1/4) (C ) 2 Whiz Flange Nut (3/8) (C ) Spacer, Hydraulic Motor Mount Sensor Bracket Sensor, Sprocket Use: 1 Carriage Bolt (1/4 x 5/8) (C ) 1 Whiz Flange Nut (1/4) (C ) Mounting Plate, Hydraulic Motor Use: 2 U-Bolt (3/8) (644-2) 4 Whiz Flange Nut (3/8) (C ) Sprocket, 13-Tooth (1-Inch Bore w/keyway) Use: 1 Key (1/4 x 1) ( ) Bushing (1-1/8 O.D. X 1/2 Long) Sprocket, 20-Tooth (7/8 Bore) Use: 2 Spring Pin (1/8 x 1-3/4) (C ) Collar, Hydraulic Speed Comp Drive Use: 1 Hex Bolt (1/4 x 1-1/4) (C ) 1 Lock Washer (1/4) (C ) 3.12 Ft... F Roller Chain #41 (54-Rollers) Use: 1 Connector Link #41 (F ) 1... L Hydraulic Control Valve, 16 GPM Use: 3 Adaptor SAE10 to 12-NPT (K ) Bracket, Motor Control Use: 2 Hex Bolt (5/16 x 3/4) (C ) 2 Whiz Flange Nut (5/16) (C ) Motor Mount Bracket Use: 1 U-Bolt (3/8) (644-2) 2 Whiz Flange Nut (3/8) (C ) Hydraulic Hoses 2... K Hydraulic Hose, 1/2 x K Hydraulic Hose, 1/2 x 14 With O-Ring Fitting On One End 1... K Hydraulic Hose, 1/2 x K Hydraulic Hose, 1/2 x K Hydraulic Hose, 3/8 x 24 (Case Drain Hose) 3... K Apt SAE10 Male to 12-NPT 1... K Steel Pipe Tee (1/2) 2... K High Pressure Sp Elbow (1/2) 1... K Steel Pipe Nipple (1/2 x 1-13/16) 1... L Cable Tie (5/16 x 15-1/4) Hydraulic By-Pass Block Assembly w/check Valve 1... K05-CV Check Valve Hydraulic By-Pass Block Page 5 of 16

6 6298-X9C Metering Door Assembles (Two Per Hopper) X9C...Metering Door Assembly 9-Outlet, Chemical (C) Black Wheels Mounting Plate, 9-Outlet (2-1/2 Cup) Use: 2 J-Bolt (C ) 2 Wrought Washer (5/16) (C ) 2 Wing Nut (5/16) (C ) 3.17 Ft.... M Rubber Strip w/adhesive (1/8 x 1/2) C1... Metering Cup Stainless (2-1/2) Use: 10 Spacer ( ) 19 Whiz Flange Nut (3/16) (C ) Hole Closures, 2-1/2 Cup Stainless Use: 9 Hex Bolt (5/16 x 1/2 Stainless) (C ) 9 Lock Washer (5/16) (C ) Metering Wheel, Chemical (C) Black (& Small Seed) Shaft (31-7/16 x 5/8 Hex) Bearing, Plastic (For 5/8 Shaft) Flangette, Bearing (For Bearing ) Use: 4 Hex Bolt (1/4 x 1/2 Stainless) (C ) 4 Lock Washer (1/4 Stainless) (C ) Sprocket 21-Tooth (5/8 Bore) Use: 1 Cotter Pin (3/16 x 1-1/4) (C ) Following Parts Are Shipped Inside Hopper: M Metering Wheel, Fertilizer (F) Red Wheel (& for Larger Seeds) Manual Holder Bracket 2... L Cable Tie (5/16 x 15-1/4) 1... M Manual Holder Blank Plate, Air Chamber 2 (Used to close off unused mixing chambers) 1... L Console Valve Adapter Cable 1... L Cable, Two Clutches, Two Shafts 1... L Grain Flow, 10 Ft, 22 Pin 1... L Grain Flow Cable, 12 Ft, 22 Pin D...Air Pressure Gauge Carton Containing: 2... C Whiz Flange Nut (1/4) 1... C Whiz Flange Nut (5/16) 1... C Hex Bolt (5/16 x 1) 2... K Adaptor, Plastic 1/4 MPT x 3/8 HB 1... K17-P Air Pressure Gauge, 4-inch 8 Ft.... M Tubing, 3/8 x 1/8 wall Mounting Bracket, Air Pressure Gauge Clamp Bracket (For Mounting Gauge on Lifting Loop) U-Bolt (1/4) (For Mounting on Ladder) Page 6 of 16

7 Hopper Assembly Page 7 of 16

8 Drive Shaft Assembly Part numbers with a (*) behind them have grease fittings. See last page. Page 8 of 16

9 Metering Door Assembly Page 9 of 16

10 Air Chamber Assembly Page 10 of 16

11 Hydraulic Blower Assembly Page 11 of 16

12 Hydraulic Drive Assembly Page 12 of 16

13 Hydraulic Hose Connections Page 13 of 16

14 Wiring Connections Page 14 of 16

15 Shaft Sensor Hydraulic Drive Sensor Page 15 of 16

16 Manual Holder Bracket Mount manual holder to corner of hopper or convergent location on implement. Store Operator s manual, Packing List & Rate Chart of convergent access. Maintenance Check all bolts for tightness after first two hours of use; check periodically thereafter. Grease all fittings regularly. There are Two grease fittings on this hopper. These must be greased before use and periodically during use. Locations: See page 8. One grease fitting on each 1-inch bearing (D ) (two) located on the 1-inch drive shaft (6299-5). Lucubrate chains as needed. Periodically clean intake screen on hydraulic driven blower. See Raven Operator s Manual for operating and wiring instructions. GDY-6680GX18-H Drawings: 6680-H, 66BS24, 6298-X9C, 6680X18-H, CP15LH-H, 66GS, 66-15FAN, 661-H, HOPSIDE-2, , HOLD1 May 21, 2014 Printed in the USA Page 16 of 16