Flow Switch Diaphragm Style Flow Switch IFW5 10 N Diaphragm style flow switch. Thread type. Nil. Body size Note)

Transcription

1 [Option] The flow switch, series IFW is used for detection and confirmation of the flow as a relaying device for the general water applications in some various equipment such as cooling water fixture in the industrial machinery. Low flow setting possible ( l /min) Simple flow setting Without removing the cover, you can set with a screwdriver from the outside. IFW5 0 N 0 Diaphragm style flow switch Thread type Nil Rc N NPT F G size Model size Set flow rate 0 0 l/min type to 0 l/min 0 0 l/min type 0 to 0 l/min l/min type 0 to 50 l/min Operating pressure: 0. MPa or less Port size 0 /8 04 / 06 /4 How to Order CE-compliant Nil Q None CE-compliant Light 0 None With neon light (0 VAC, ) With neon light (0 VAC, Green) With neon light (0 VAC, ) 4 With neon light (0 VAC, Green) 5 With LED light (4 VDC, ) 6 With LED light (4 VDC, Green) LED light is available for 5, 6, 7, 8 (with terminal box for 4 VDC). Terminal box 0 Without terminal box (: ab) With terminal box (: a) With terminal box (: b) 5 With terminal box (4 VDC, + COM, : b) 6 With terminal box (4 VDC, + COM, : a) 7 With terminal box (4 VDC, COM, : b) 8 With terminal box (4 VDC, COM, : a) Terminal box for 4 VDC is available for 5, 6 (LED light). Specifications Fluid Operating pressure Water resistance Operating temperature range Operation Insulation resistance Withstand voltage Port size material in contact with fluid material About the use of, please confirm SMC. Diaphragm Water/Non-corrosive liquid 0. to 0.6 MPa. MPa 5 to 60 C (No freezing) Diaphragm style 00 MΩ (500 DC by megameter) 500 VAC for one min. Without terminal box: ab With terminal box: a or b /8, /, /4 CAC408 C604B NBR 04

2 Micro Switch Ratings Model Voltage 5 VAC 50 VAC 8 VDC 4 VDC 0 VDC 5 VDC 50 VDC Non inductive load (A) Inductive load (A) Load resistance Light load Inductive load Motor load N.C. N.O. N.C. N.O. N.C. N.O. N.C. N.O Model IFW50 IFW50 IFW550 Flow range Max. flow Hysteresis to 0 0 or less 0 to or less 0 to or less Hysteresis is the flow rate that is necessary for moving the microswitch from the operation position (ON signal) to the return position (OFF signal). Construction/Working Principle Flow Characteristics IFW50 Adjusting gear Gear Flow setting indication lever Micro switch Operating lever Protection diaphragm P=0.6MPa P=0.5MPa P=0.4MPa P=0.MPa P=0.MPa P=0.MPa Flow rate IFW50 PFM P=0.6MPa P=0.5MPa P=0.4MPa P=0.MPa P=0.MPa P=0.MPa PFMV PFA PFW PFD IF Working Principle Liquid flow creates a pressure differential nearby the orifice of the port of the body q. One set of diaphragms monitors the pressure differential and operates the micro switch through the rod w and operating lever r. The rod w moves downward with increased flow, and upward with decreased flow. Moving the gear t upward or downward by the adjusting gear e manually offers an electric signal at various flow rates. Component Parts No. Description Gear Material CAC408 C604B POM No. 4 5 Description Operating lever Adjusting gear Material SPCC POM IFW Flow rate P=0.6MPa P=0.5MPa P=0.4MPa P=0.MPa P=0.MPa P=0.MPa Flow rate 05

3 Dimensions IFW to 04 (Without terminal box) With neon light Lead wire length ( 500 IFW to 4 (With terminal box) With neon light 06

4 Dimensions IFW to 86 (With light, Terminal box for 4 VDC) PFM PFMV PFA PFW PFD IF 07

5 Internal Wiring Diagram IFW /0/0 C A B C A B Common Normally Open Normally Closed IFW to 04/ to 4/ to 4 IFW /56 4 VDC Common Normally Open Normally Closed Blue Precautions Be sure to read before handling. Refer to front matters 58 and 59 for Safety Instructions and pages 89 to 896 for Flow Switch Precautions. Caution Mounting & Wiring. Mount a switch, so that the liquid flow is in the same direction as that of the arrow on the body.. The flow switch can be installed either horizontally or vertically.. Provide a straight pipe portion that corresponds to approximately 5 times the bore of the pipe before and after the area of the pipe on which the product is installed, thus keeping the product as far away as possible from the elements that disturb the flow, such as elbows or valves. 4. For wiring, refer to the internal wiring diagram. 5. If a terminal box is not available, wire by selecting the contact at a or b. At that time, insulate the s that will not be used. 6. Because this is an open style, it cannot be used where water or oil splashes. 7. It cannot be used if a water hammer or pulsation pressure is applied to the fluid. 8. In order to prevent a malfunction or diaphragm damage caused by debris or cutting chips in the fluid, install a filter with approximately 00 mesh on the inlet side of a flow switch. IFW /66 4 VDC IFW /76 4 VDC IFW /86 4 VDC Blue Gray Gray Caution Adjusting. To adjust flow, remove grommet of the upper cover and rotate flow adjusting gear using a flat head screwdriver. Turning clockwise can increase the set flow and turning counterclock can decrease the set flow.. The flow rate setting point is set at the ON flow rate. Therefore, in the case of the a contact, the ON signal is output if fluid with a higher flow rate than the set flow rate has occurred. In the case of the b contact, the ON signal is output when the flow rate has decreased from the set flow rate for the amount that corresponds to the hysteresis.. To prevent the chattering that is associated with the fluctuation of the operating flow rate, set the difference between the set flow rate and the operating flow rate so that it is as large as possible. 4. Use at or below the maximum operating pressure and maximum flow rate. 5. The indicator on the window name plate (Fig. ) is only a guideline. For precise setting, mount a flow meter on the downstream side of the flow switch, and set the level. Also, when setting levels with a low flow rate at pressures of 0. MPa or more, there may be interference between the indicator needle and the scale plate. In such cases, detach the indicator needle and scale plate before setting. After setting, the indicator needle and scale plate can be reattached in positions of your choice. Graduations for adjusting on flow rate Graduations for IN pressure 0. MPa Graduations for IN pressure 0. MPa 08 Fig. Window name plate