Service & Maintenance TA-25 Basic Loader Parts

Transcription

1 TA- Basic Loader Parts 0 0 TA- LOADER TOWER REPLACEMENT PARTS RT-AS - R TOWER (RIGHT) HHS00 /" X /" BOLT RT-AS - L TOWER (LEFT) CBF00 /" X /" CARRIAGE BOLT RT-AS SHOE CBF000 /" X " CARRIAGE BOLT RT-0AS - R SLIDE LOCK (RIGHT) AHS000 /" X /" SET SCREW RT-0AS - L SLIDE LOCK (LEFT) AHS00 /" X " SET SCREW RT- LATCH LWM0 /" LOCK WASHER RT- LATCH RIVOT HTN0 /" LOCK NUT 0H00 FRONT WRAP * HTN0 /" LOCK NUT MT- WASHER FWW /" FLAT WASHER 0 QC-0 WASHER NOTE: *Varies by Tractor (Standard Front Wrap is 0H00). WESTENDORFMFG PWB0 WESTENDORF MFG CO., INC. PH: () - FAX: () -0 sales@westendorfmfg.com

2 TA- Basic Loader Parts 0 TA- LOADER FRAME REPLACEMENT PARTS RF-AS FRAME RF- INNER GAUGE ROD MF-0AS GAUGE ROD HOLDER B-0 INSERT BUSHING RF-AS GAUGE ROD PIN LF-AS LIFT PIN ZER0 GREASE FITTING CBF000 /" X " CARRIAGE BOLT HTN0 /" LOCK NUT 0 CTK0000 /" X " COTTER KEY. WESTENDORFMFG PWB0 WESTENDORF MFG. CO., INC. PH:() - FAX: () -0 sales@westendorfmfg.com

3 TA- Buckets and Couplers BUCKET 0Q 0" BUCKET Q " BUCKET QS " SKID STEER BUCKET QS " SKID STEER BUCKET MB- 0" BLADE IB- BLADE JB- " BLADE MB- SIDE BLADE NOTE: *Check width of the bucket and use the part number that matches. If your size is not shown, contact Westendorf Mfg. Co. COUPLER (C-) 0 C- QC-0AS COUPLER QC-AS HANDLE QC- BAR CATCH QC-AS LOCK PIVOT PLATE QC-AS LATCH ROD QC-0 SPRING B-0 INSERT BUSHING CBF00 /" X /" CARRIAGE BOLT CBF000 /" X " CARRIAGE BOLT 0 HTN0 /" LOCK NUT HTN0 /" LOCK NUT SR-E0 RETAINING RING OPTIONAL SKID STEER COUPLER C-0 COUPLER COSMETICS DEC- DECAL KIT V--A BLACK SPRAY PAINT V--P PINT BLACK PAINT. REF # PART # DESCRIPTION QTY V--Q QUART BLACK PAINT V--G GALLON BLACK PAINT WESTENDORFMFG PWB0 WESTENDORF MFG. CO., INC. PH: () - FAX: () -0 sales@westendorfmfg.com

4 TA- Bucket Cylinder STEPS TO REPAIR CYLINDER ) Extend the ram out as far as possible. ) At the ram end of the cylinder barrel you will find a snap ring located either on the face or inside the notch of the gland. ) Locate the snap ring eyes (you may need to turn the gland inside the barrel to find the snap ring eyes). Compress the snap ring with snap ring pliers. ) Remove the ram assembly (ram, gland, & piston) from barrel. ) Notice the direction they're pointing so they can be properly re-assembled. ) Remove the jam nut and/or hex nut from the end of the ram. ) Remove the old seals and rings and replace them with the new seals and rings. (Seal kits are packaged for several different cylinders. You may have extra parts) ) Clean cylinder with cleaner and a clean lint free cloth. ) Lubricate the seals and rings to aid assembly. 0) Assemble the cylinder by reversing the order. CYLINDER REPAIR TIPS When disassembling cylinders, keep the parts in correct orientation. Remove parts in sequence. Note the direction of the piston and gland. Lay out old seals and parts as they are removed. Assemble cylinder in proper order; lubricate to aid assembly. BUCKET CYLINDER REPLACEMENT PARTS REF # PART # DESCRIPTION QTY B- CYLINDER B-0 BARREL B-0 RAM G-H GLAND P-C PISTON HFN " NUT ZER0 GREASE FITTING B- INSERT BUSHING 0 #CK SEAL KIT * B-0 INSERT BUSHING NOTE: * Seal kit contains parts to repair one cylinder. WESTENDORFMFG PWB0 WESTENDORF MFG. CO., INC. PH: () - FAX: () -0 sales@westendorfmfg.com

5 TA- Lift Cylinder 0 STEPS TO REPAIR CYLINDER ) Extend the ram out as far as possible. ) At the ram end of the cylinder barrel you will find a snap ring located either on the face or inside the notch of the gland. ) Locate the snap ring eyes (you may need to turn the gland inside the barrel to find the snap ring eyes). Compress the snap ring with snap ring pliers. ) Remove the ram assembly (ram, gland, & piston) from barrel. ) Notice the direction they're pointing so they can be properly re-assembled. ) Remove the jam nut and/or hex nut from the end of the ram. ) Remove the old seals and rings and replace them with the new seals and rings. (Seal kits are packaged for several different cylinders. You may have extra parts) ) Clean cylinder with cleaner and a clean lint free cloth. ) Lubricate the seals and rings to aid assembly. 0) Assemble the cylinder by reversing the order. CYLINDER REPAIR TIPS When disassembling cylinders, keep the parts in correct orientation. Remove parts in sequence. Note the direction of the piston and gland. Lay out old seals and parts as they are removed. Assemble cylinder in proper order; lubricate to aid assembly. LIFT CYLINDER REPLACEMENT PARTS L- LIFT CYLINDER L-0 BARREL B-0 RAM G-A GLAND P-A PISTON HFN " NUT ZER0 GREASE FITTING B-0 INSERT BUSHING 0 B- INSERT BUSHING #CK SEAL KIT * NOTE: * Seal kit contains parts to repair one cylinder WESTENDORFMFG PWB0 WESTENDORF MFG. CO., INC. PH: () - FAX: () -0 sales@westendorfmfg.com

6 TA- Hydraulics 0 TA- HYDRAULICS PF-FFC FEMALE CONNECTOR PF-FSBT SWIVEL NUT TEE OLT- OIL LINE OLT- OIL LINE OLT-0 OIL LINE OLT- OIL LINE OLT- OIL LINE OLT- OIL LINE OLT- OIL LINE 0 OLT- OIL LINE OH- OIL LINE HOLDER OH- OIL LINE HOLDER OH- OIL LINE HOLDER H000-FF /" X 0" HOSE H000-FF /" X 0" HOSE HTN0 /" LOCK NUT. WESTENDORFMFG PWB0 WESTENDORF MFG. CO., INC. PH: () - FAX: () -0 sales@westendorfmfg.com