MOISTURE LIQUID INDICATORS

Transcription

1 MOISTURE LIQUI INITORS HENRY TEHNOLOGIES SIGHT GLSSES (ULLS EYE TYPE) lear Lens SG-1000 Series Reflex Lens SG-1100 Series P4453 These sight glasses are available in three basic styles; lear Lens; Reflex Lens; and lear Lens with Floating all. ll sight glasses feature a nickel plated steel body, hermetically sealed viewing lens, merican standard tapered pipe thread, 500 PSI maximum working pressure. These sight glasses are suitable for most standard refrigerants, and other industrial fluids non-corrosive to glass and steel (for R-11 applications, an aluminum ball is available for the SG-1200 s add suffix i.e. SG-1206). The SG-1000 s & SG-1100 s are rated for a maximum temperature of 500 F (260 ). The SG-1200's are rated for a maximum temperature of 300 F (148 ). The SG-1100 s (Reflex Lens) look dark when liquid is present and light when liquid is absent. P4453 lear Lens with Floating all SG Series PRT IMENSIONS (in.) THRE lear Reflex lear/ SIZE (in.) With all M.P.T. SG-1004 SG-1104 SG /2 SG-1006 SG-1106 SG /4 SG-1008 SG-1108 SG SG-1010 SG-1110 SG /4 SG-1012 SG-1112 SG /2 SG-1016 SG-1116 SG HENRY TEHNOLOGIES VERTIL SME SUTION LINE UMULTORS Inlet Outlet 1/4" FPT Relief onnection Inlet Outlet 1/4" FPT Relief onnection E* * HE Models Only HE: Heat Exchange models available by ordering with an HE suffix (ie. S-7721HE). Heat Exchange models feature a boil out coil to boil off liquid refrigerant in the bottom of the accumulator. The OS connection size of the boil out coil is shown in column E. *Optional: 1" FPT connection is available on S-7700 series for installation of a S type Liquid Level Switch. onsult factory. SPEIFITIONS P4454 S-7000 Series Maximum WP 400 PSI S-7000 Series Heat Exchange Model P in. FPT Model* PRT Std Heat Exchanger OS ONN. IMENSIONS IN INHES I. OS E S-7722 S-7721 S-7721HE 2-1/8 8-5/ /8 S-7726 S-7725 S-7725HE 2-5/8 10-3/ /8 S-7732 S-7731 S-7731HE 3-1/8 12-3/ /8 N S-7741 S-7741HE 4-1/ ontact Factory 2-5/8 N S / ontact Factory N/ PRT REFRIGERNT HOLING P. (lb 0 F sat) R-134a R-22 R-404a/ R-507 S S S S S MX MIN MX MIN MX MIN MX MIN MX MIN REFRIGERNT REOMMENE TONS REFRIGERTION T SUTION EVPORTING TEMPERTURE ( F) R-134a R-22 R-404/R F +20 F +0 F -20 F -40 F +40 F +20 F +0 F -20 F -40 F +40 F +20 F +0 F -20 F -40 F

2 UMULTORS N MUFFLERS HENRY TEHNOLOGIES HORIZONTL UMULTORS Liquid accumulators of this design should not be used when the temperature of the liquid refrigerant is less than +15 F in the accumulator. These accumulators have a 1/2-in. FPT connection for liquid injection and a 3/4-in. FPT connection for hot gas bypass. These connections can also be used for a relief device as required by UL 207. MXIMUM WP 302 PSI S-7600 SERIES P1147 PRT SIZE ONN. IMENSIONS (in.) ia REFRIGERNT HOLING P. (lbs 0 F ST.) REOMMENE TONS OF REFRIGERNT T SUTION EVPORTING TEMPERTURE ( F) R-134a R-22 R-404/R-507 R-134a R-22 R0404/R F +20 F +0 F +40 F +20 F +0 F +40 F +20 F +0 F S /8 OS S /8 OS S /8 OS HENRY TEHNOLOGIES ISHRGE LINE MUFFLERS PRT SIZE ONN. ia. S /2 OS 7.75 S /8 OS S /8 OS 9.69 S /8 OS 9.69 S /8 OS 6.75 S /8 OS 7 S /8 OS S /8 OS S /8 OS S /8 OS 21 S /8 OS 6 21 S /8 OS P1148 Selecting the Size of a Muffler Select a muffler with a connection size that matches or exceeds the line size of the compressor discharge line. There are no tonnage ratings for mufflers, since the muffler will remove pulsations from the discharge regardless of flow. S-6300 Series: Maximum working pressure 500 psig. S-6400 and S-6600 Series: Maximum working pressure 450 psig. 655

3 LIQUI REFRIGERNT REEIVERS HENRY TEHNOLOGIES LIQUI REFRIGERNT REEIVERS Receivers should be selected based on the operating charge for all system components, including the liquid lines. It is usual to add a small percentage to cover the refrigerant in long runs of suction and discharge lines, etc. It is essential that the maximum operating charge be determined, e.g., winter charge in air cooled condenser having flooded head pressure control, this being much greater than the normal summer charge. S-8060 SERIES VERTIL REEIVERS P1149 PRT *PUMP OWN PITY (lbs) R404/ R-134a R-22 R-507 IMENSIONS (in.) Maximum WP 450 PS *ll Pump own apacities are 90% of receiver 90 F. ia. ONNETIONS Inlet Outlet S S S /4 FLRE 1/4 FLRE 3 S S S /8 FLRE 3/8 FLRE 10 S /8 FLRE 1/2 FLRE S /2 FLRE 1/2 FLRE 21 S /8 FLRE 5/8 FLRE 26 WT. S-8600 SERIES HORIZONTL REEIVERS S-8600V SERIES HORIZONTL REEIVERS w/ RKETS & VLVES P1150 S-8600 SERIES HORIZONTL REEIVERS PRT MXIMUM WP 450 PSI *PUMP OWN PITY (lbs) IMENSIONS (in.) INLET SHIP R-404/ I. WEIGHT R-134a R-22 Inlet Outlet FPT R-507 (lb) /8 OS 5/8 OS 3/8 S S S /8 OS 5/8 OS 3/8 S S-8600V SERIES HORIZONTL REEIVERS WITH RKETS & VLVES PRT *PUMP OWN PITY (lbs) IMENSIONS (in.) ONNETIONS SHIP R-404/ I. WEIGHT R-134a R-22 E F G Inlet Outlet FPT R-507 (lb) S-8600V /2 OS 1/2 OS 3/8 19 S-8630V /2 OS 1/2 OS 3/8 28 *Pump own apacities are 90% of receiver 90 F. 656

4 LIQUI REFRIGERNT REEIVER ESSORIES HENRY TEHNOLOGIES REEIVER ESSORIES LIQUI LEVEL GUGES PRT REEIVER I. S /8 S /4 S /4 S S S S Mating flanges for level gauges not included on most receivers. P1165 RKET KITS PRT REEIVER I / / /4 NOTE: esigned for horizontal mounting use only. P1166 ROTO-LO VLVES PRT THRE OS / /4-12 7/ / / / / /8 Includes gasket. P1167 ROTO-LO/OS PTERS PRT THRE OS / /4-12 7/ / /8 Male stub designed for use on OS receiver connections when a Roto-Loc is desired. P

5 OIL SEPRTORS HENRY TEHNOLOGIES HELIL OIL SEPRTORS The helical oil separator features a centrifugal flow path achieving approximately 99% efficiency of oil separation with low pressure drop. P1151 S-5108/S-5181 S-5182 THRU S-5188 S-5190/S-5192 S-5290/S-5292 S-5202/S-5203/S-5204 PRT SIZE ONN. ia IMENSIONS (in.) MX. PITY IN TONS OF REFRIGERTION T EVPORTOR TEMPERTURE (nominal) R-134a R-22 R-404/R F +20 F +40 F +20 F +40 F +20 F MXIMUM ISHRGE FM S-5100 s - onnections are nickel plated steel. S-5200 s - onnections are copper plated steel. ll the capacities shown are based on 100 F condensing. Minimum tonnage is 33% of rated capacity, oversizing is not acceptable. PRE-HRGE MOUNT (oz) S /4 OS S /8 OS S /2 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS S /8 OS

6 OIL SEPRTORS HENRY TEHNOLOGIES ONVENTIONL OIL SEPRTORS P1152 PITY IN TONS OF REFRIGERTION T PRE- IMENSIONS MXIMUM PRT SIZE EVPORTOR TEMPERTURE (nominal) HRGE (in.) ISHRGE ONN. R-134a R-22 R-404/R-507 MOUNT FM ia 40 F +40 F 40 F +40 F 40 F +40 F (oz) S /2 OS S /8 OS S /8 OS S /8 OS S /8 OS onnections are nickel plated steel. Oil flow 175 PSI differential.80 gal/min. 3/8 flare oil return connection ll other capacities shown are based on 100 F condensing. Minimum tonnage is 33% of rated capacity, oversizing is not acceptable. S-5500 s ISHRGE FM HRTS FM HRT - R-22 FM HRT - R-404a/R/507 P1153 P1155 FM HRT - R-134a HOW TO LULTE ISHRGE FM (FM) Example: 50 ton R-22 system -25 F Evaporator Temp. 115 F ondensing Temp. From the R-22 FM hart, follow the -25 F evaporator temperature line to the intersection of the 115 F condensing temperature line. Extend a line horizontally from this point to the FM/ton factor. Multiply the FM/ton factor by the total tonnage to calculate the total FM. Example: P FM x 50 ton = 36.0 FM ton Oil Separator Selected: S

7 OIL SEPRTOR ESSORIES HENRY TEHNOLOGIES HET ELEMENTS J-Series Heat elements add heat to oil separators to prevent migration of refrigerant to the vessel during off cycles of the compressor. Heatelementscanalsobeusedonsuctionline accumulators to warm the oil and allow oil return to the compressor on low temperature applications. P4455 S-9101 P4455 PRT IMETER (in.) WTTGE VOLTS S-9112J 6 50W 240V S-9113J 4 25W 120V S-9114J 4 25W 240V S-9115J 2-1/2 25W 120V S W 110V S W 220V S W 220V P4456 P4456 OIL SEPRTORS The Replacement Float ssembly is used on the S-5200 & S-1900 series Oil Separators, and the is used on the S-5700 series Oil Separators. oth Replacement ssemblies include the gasket which can also be ordered separately (Part Number ). The S-5700 series screen cartridge can also be ordered as a replacement part (Part Number ). 3/8" OS oil return connection is available by ordering with an "X" suffix (i.e X). The Replacement Float ssembly is used on the S-5800 series Oil Separators. The Replacement ssembly includes the gasket (Part Number ). Part No. : Part No.: Part No.: P4457 P

8 OIL LEVEL REGULTORS (ONVENTIONL) HENRY TEHNOLOGIES OIL LEVEL REGULTORS The oil level regulator controls the oil level in the compressor crankcase with a float operated valve. Oil level regulators are designed to attach directly to the sight glass housing on compressor crankcases. dapter kits are available for compressors that have a different sight glass configuration. The sight glass from the compressor or supplied with an adapter kit, bolts to the second regulator flange for visual observation of the oil level. EQULIZTION ONN. 3/8" FLRE OIL LINE ONN. 3/8" FLRE 1/8 IN. S-9010 FIXE LEVEL REGULTOR The S-9010 regulator maintains the oil level in the compressor crankcase at 1/8-in. sight glass. The S-9010 maintains the level at any pressure differential* between 5 and 30 psi. The S-9010 oil level regulator is designed to bolt directly to the 3 bolt sight glass housing found on many compressor crankcases. o not use on Satellite ompressor. Part No.: S-9010 P1156 EQULIZTION ONN. 3/8" FLRE OIL LINE ONN. 3/8" FLRE JUSTMENT SREW S-9090 JUSTLE REGULTOR One oil level regulator for all applications The S-9090 regulator allows the oil level in the compressor crankcase to be maintained at any level between 1/4 and 1/2 sight glass. The S-9090 maintains the level at any pressure differential* between 5 and 90 psi. If the oil level in the crankcase is too high or too low, the level can be adjusted by turning the adjustment screw on top of the regulator. This can be done while the system is in operation. Our exclusive design eliminates the need of shutting down the system and disconnecting the oil feed lines in order to adjust the regulator. P1157 Part No.: S-9090 EQULIZTION ONN. 3/8" FLRE OIL LINE ONN. 3/8" FLRE JUSTMENT SREW P1158 *Operating Pressure ifferential The difference between the oil fed to the oil regulator and its compressor crankcase, where the regulator is controlling oil level. S-9130 JUSTLE REGULTOR The S-9130 regulator allows the oil level in the compressor crankcase to be maintained at any level between 1/4 and 1/2 sight glass. The S-9130 maintains the level at any pressure differential* between 5 and 90 psi. If the oil level in the crankcase is too high or too low, the level can be adjusted by turning the adjustment screw on top of the regulator. This can be done while the system is in operation. Our exclusive design eliminates the need of shutting down the system and disconnecting the oil feed lines in order to adjust the regulator. Part No.: S

9 OIL LEVEL REGULTORS (ONVENTIONL) HENRY TEHNOLOGIES ELETRO-MEHNIL OIL LEVEL REGULTORS S-9030 djustable Regulator The Electro-Mechanical Oil Level Regulator S-9030 provide a simplistic means for controlling oil level for hermetic, semi-hermetic, reciprocating and scroll compressors. through the use of a float switch and solenoid valve. magnetic reed float switch closes upon the reduction of oil level in the oil regulator body. This action energizes the solenoid valve thereby feeding oil into the regulator body. The oil level is adjustable by loosening the compression nut and manually adjusting the position of the float switch. low level alarm is also provided, for oil safety on hermetic and scroll compressors. If the oil level drops 1/8" below the set point, a second magnetic reed switch closes activating a customer supplied alarm. This alarm circuit may also be used to disconnect power from the compressor. While the regulator is in alarm the solenoid valve remains open trying to re-establish the oil level. Features: omplete oil level control without variations in pressure drop. 3/8" Flare normally closed solenoid valve. djustable between 1/4" and 1/2" glass. Low level alarm circuit. 24 Vac.25 amp. No UL considerations. Equalization connection 3/8" Flare. Operating differential 5 to 300 psig. Reliable float switch operation, 20 Va. pilot duty. ll major components replaceable. P4459 S-9030 djustable Regulator One oil level regulator for all applications The S-9030 Oil Level Regulator is designed to bolt directly to the three bolt sight glass housing found on many compressor crankcases. dapter kits are available for compressors that have a different sight glass configuration. The sight glass from the compressor or supplied with an adapter kit, bolts to the second regulator flange for visual observation of the oil level. LISTE " ia 3.18 P

10 OIL RESERVOIRS HENRY TEHNOLOGIES OIL RESERVOIR ue to system design, loads & defrost cycles, varying amounts of oil can be returned by the oil separator. ecause of this, a safety reserve of oil is required for the operation of our oil control system. The oil reservoir is the holding vessel for this stand-by oil. It has sight glass ports to observe the oil level inside the vessel. The valve on top of the Oil Reservoir receives oil from the Oil Separator, and the bottom valve distributes oil to the Oil Level Regulators. The valves are backseating and have a 1/4" flare connection, allowing the addition or removal of oil from the reservoir. High pressure gas returns with the oil from the Oil Separator to the Oil Reservoir. Pressure could build up in the Oil Reservoir to adversely affect the Oil Regulators. To prevent this, a vent line is installed from the top of the Oil Reservoir to the suction line. This line permits the pressure in the Oil Reservoir to be approximately the same as the suction line and the compressor crankcases. The 4 gallon model at. No. S-9108 should be used on very large systems, or systems with excessive oil charges, long line runs or any case where suction oil return may be impeded. New System Start-Up On system start-up of a new parallel system, oil should be added to the OIL RESERVOIR to the upper sight glass port, NOT OVE IT. It is commonly accepted that in a new refrigeration system, some oil will be absorbed by the refrigerant as the system becomes balanced out. fter two hours of operation, the OIL RESERVOIR, if necessary, should again be filled to the upper sight glass, and also after two days, by which time the entire refrigeration system should be balanced out. Then the OIL RESERVOIR must be observed on each service call. No oil should be added again until the oil level falls below the lower sight glass port. Existing System Start-Up When installing this OIL ONTROL SYSTEM, on a parallel system that has been in operation for some time, the amount of oil should be added cautiously. With the efficiency of the new OIL SEPRTOR, the oil return could likely be sufficient to fill the OIL RESERVOIR to the lower sight glass port only. Observe for one day. fter the second day, if the oil level has not risen to the upper sight glass, add oil. If the oil level has risen above the upper sight glass port, remove the excess oil from the OIL RESERVOIR. S-9109 S " ia P4468 P4468 P4467 P4467 LISTE OF IMENSIONS PRT PITY (IN GLLONS) SIGHT (in.) GLSSES S /2 3/ S /4 3/

11 OIL LEVEL ONTROL ESSORIES HENRY TEHNOLOGIES ELETRONI OIL LEVEL ONTROL N ESSORIES The Electronic Oil Level ontrol System is a new type of oil level control technology for use on multiple compressor refrigeration systems. The system consists of on Oil Level ontroller which allows a preset oil level to be maintained in each compressor. It uses an optical Oil Level Transducer (1 per compressor) to sense oil level in each compressor crankcase. Part Number S-9310 djustable ontroller can maintain between a 1/4 and a 1/2 oil level in a compressor crankcase and the operating differential of 5-90 psig. The additional necessary hardware for the S-9310 includes the S-9310M or solenoid valves, and the S-9330 Transducer. The S-9310 is factory wired for 230 V but can be changed in the field to 115 V. Part Number S-9330 Transducer is used with the S-9310 adjustable Electronic Oil Level ontroller. The S-9330 transducer optically senses the oil level through the sight glass & transmits a signal to the controller. P4461 NOTE: The S-4004 or S-4005 Oil Filters must be used to capture any foreign material that will ultimately cause the Electronic Oil Level ontrol System problems. Not using the same type of oil filters will void the warranty. S-9330 P OLT 1 7/8".. P4462 Part Number S-9310M Solenoid Manifold is used with the S-9310 Electronic Oil Level ontroller. S-9310M feeds oil to the crankcase when the controller calls for oil. The S-9310M is designed to be mounted externally of the wiring panel. Part Number Solenoid Valve is used with the S-9310 Electronic Oil Level ontroller. The solenoid valve is piped directly in the oil return line to the compressor. 3/8" Flare From Oil Resevoir 3.25" P4463 Part Number Sight Glass dapter Kit is for compressors with only one crank-case sight glass. The 3-olt flange Oil Level Transducer (S-9330) does not allow for a visual observation of the oil level in compressors. This adapter kit provides an additional sight glass and a 1/4" flare equalization/oil fill connection. Vent Oil Reservoir Oil Filter Sight Glass S-9330 Transducer 3/8" Flare Reservoir Pressure Valve Solenoids & Manifold P4465 S-9310 ontroller Oil Separator Satellite ompressor Parallel ompressors 3 olt 1 7/8".. P4464 P

12 OIL LEVEL REGULTORS N ONTROL ESSORIES HENRY TEHNOLOGIES OIL LEVEL REGULTOR PTER KIT SIGHT GLSS OIL LEVEL OMPRESSOR MNUFTURER SIGHT GLSS ONFIGURTION PTER KIT PRT 1/2 unham-ush ig 4 3 olt 1-7/ * 1/2 Trane 3 olt 1-7/ * 1/2 York 3 olt 1-7/ * 1/4 arrier (models E & ER) 3 olt 1-7/ * 1/4 opeland (over 5 tons) 3 olt 1-7/ * 1/2 opeland (under 5 tons) 1-1/8-12 Thread /2 Prestcold (model K ) 1-1/8-12 Thread /2 unham-ush (model ) 4 olt 2-1/ /4 arrier (,R,5F,5H & 06) 1-1/2-18 Thread /2 Schnacke-Grasso 2 x 16 Thread /2 Trane 5 olt 2-1/ SIGHT GLSS OIL LEVEL OMPRESSOR MNUFTURER SIGHT GLSS ONFIGURTION PTER KIT PRT 1/4 opeland (older model) 4 olt 2-1/ /2 Vilter 1-1/2 NPT Thread /2 Vilter 2 NPT Thread /4 opeland (model 8R ) 3 olt 1-7/ /2 Prestcold (,E,R,L, & LG) 42mm Thread /2 Trane (model K ) 3/4 NPT Thread /2 Schancke-Grasso 1-1/4 NPT Thread /2 Grasso Thermtrol 1 NPT Thread /2 ristol 15/16-20 Thread /2 ock 4 olt 1-31/ /2 Maneurop 1-1/8-18 thread /2 itzer 4 olt ll kits include necessary hardware, gaskets and sight glasses to mount Oil Level Regulators to various compressors shown in this table. *KIT INLUE WITH LL OIL LEVEL REGULTORS NOTE: For compressors not listed above, a universal adapter kit is available Part No This adapter kit has a 3-hole flange to mount to the regulator. The compressor end of the kit is a 1-1/4" O steel tube. The existing compressor sight glass gland or flange must be bored out or bushed down to accept the 1-1/4" tube. The tube is then brazed or welded to the reworked gland or flange and installed on the compressor. P4474 HENRY TEHNOLOGIES OIL LEVEL ONTROL OMPONENTS PRESSURE VLVE PRT PRESSURE SETTING S lbs S-9104H Used with oil reservoir. 20 lbs SHUT-OFF RSS VLVES SIZE ONNETION 3/8 Female x 3/8 Male Flare 3/8 Female x 3/8 Male Flare 2.47" PRT TYPE S-9106H 3/8 Flare 3/8 Fem. Flare Vertical S-9106V 3/8 Flare 3/8 Fem. Flare Horizontal Vertical Type INLET Horizontal Type INLET P1159 EQULIZTION PTER KIT PRT " 1/4" FLRE SIGHT GLSS INSTLLTION TOOL Used on all 06, 06, and 06E models. Part No.: T OLT 1 7/8".. P1162 P4405 (SWIVEL ONNETION) OIL LINE STRINER (SWIVEL ONNETION) P RREL NUT SOKET Special socket to remove and torque 06 terminal nuts. Used on all 06 models. Part No.: P PRT ONNETION SREEN SIZE. T S /8 Flare 100 Mesh x 11 sq. in. Used to protect oil regulators by removing foreign matter. 5" 3/8 OS connections available by ordering with an X suffix (i.e., S-9105X) P

13 REFRIGERTION OIL FILTER RIERS HENRY TEHNOLOGIES OIL FILTER POE OIL FILTER-RIER Part Number S-4004 Our S-4004 Oil Filter removes foreign material from the oil as it passes through the filter. The filter easily captures any debris that may be in the system, such as dirt, metal chips, etc. (particle retention 10 micron). The S-4004 is required on all Electronic Oil Level ontrollers to protect the solenoid manifold. P4469 Part Number S-4005 POE Oil Filter & rier for POE oil return on systems using Oil Separators and Oil ontrol Systems. This is not a refrigerant Filter rier. It is designed to operate at a very low pressure drop in a 100% oil environment. P4470 Part Number S-4005 POE Oil Filter & rier was designed to clean and dry POE oil as it is returned to the compressor crankcase or Oil Reservoir in parallel systems.lean and dry POE oil assures the proper operation of the float assemblies in the Oil Separator and the Oil Level Regulators. P4471 S-4004 & S /8" Flare 3/8" Flare New POE Oil Filter & rier 4" 7 3/8" P4472 P

14 HEK VLVES HENRY TEHNOLOGIES HEK VLVES (Globe esign) FORGE RSS OY TYPE 116 TEMPERTURE RTING 40 F TO +300 F MXIMUM WORKING PRESSURE 500 PSI P440 FORGE RSS OY ( ) Teflon synthetic seat, with fully guided piston and stainless steel spring. Will operate in any position except bonnet down. Internal parts can be easily removed to prevent damage when soldering valve into line. Suitable for highside or lowside installation and hot gas applications, refrigerants and other industrial fluids, non-corrosive to brass and steel. INLET P4478 PRT SIZE ONN. IMENSIONS IN INHES WT (Lb) /8 OS /2 OS /8 OS /8 OS TYPE 205 MXIMUM WORKING PRESSURE 500 PSI TEMPERTURE RTING 20 F TO +300 F Type 205 INLET P443 P4477 PRT SIZE ONN. IMENSIONS IN INHES WT (Lb) 205-7/8 7/ /8 1-1/ /8 1-3/ /8 1-5/ /8 2-1/ /8 2-5/

15 HEK VLVES HENRY TEHNOLOGIES HEK VLVES (Straight Through esign) RSS OY TYPE 119 rass onstruction with Synthetic Rubber Seat omplete Piston Guidance Stainless Steel Spring Operates in ny Position Temperature Rating 20 F to +200 F Maximum Working Pressure 500 PSI ompact, sturdy and noiseless in operation, with minimum pressure drop. Type 119 S..E. Male Flare P4475 PRT SIZE ONN. IMENSIONS IN INHES WT (Lb) 119-1/4 1/4 FL /8 3/8 FL RSS OY TYPE 120 P442 SOLER ONNETIONS EXTENE OPPER ENS 120 ( ) Type 120 Solder rass onstruction with Synthetic Rubber Seat omplete Piston Guidance Stainless Steel Spring Operates in ny Position Temperature Rating 20 F to 200 F Maximum Working Pressure 500 PSI ompact, sturdy and noiseless in operation, with minimum pressure drop. P4476 PRT SIZE ONN. IMENSIONS IN INHES WT (Lb) 120-3/8 3/8 OS /2 1/2 OS /8 5/8 OS /8 7/8 OS HENRY TEHNOLOGIES NGLE HEK VLVES P445 SIZE IMENSIONS (in.) PRT ONNETONS enter to enter to Overall (in.) ottom Side Height 215-7/8 7/8 OS 1-1/2 1-3/4 3-3/ /8 1-1/8 OS 1-3/4 2-3/16 3-7/ /8 1-3/8 OS 1-15/16 2-7/16 4-3/ /8 1-5/8 OS 2-5/32 2-3/4 5-1/16 668

16 PKLESS VLVES HENRY TEHNOLOGIES PKLESS VLVES Standard Type Forged rass ored ody and onnet Recommended for Vacuum pplications and Service Pressures up to 500 PSI Non-irectional Flow ackseating Lower Stem iaphragms are hangeable Under Line Pressure Temperature Rating 20 F to +275 F Standard Globe Valves O.. Solder P4479 PRT SIZE ONN. IMENSIONS IN INHES WT (in.) Mtg Hole trs (lb) 6261N 1/4 OS N 3/8 OS N 1/2 OS N 5/8 OS N 3/4 OS N 7/8 OS N 1-1/8 OS Standard ngle Valves O.. Solder P4480 PRT SIZE ONN. IMENSIONS IN INHES WT (in.) (lb) 6471N 1/4 OS N 3/8 OS N 1/2 OS N 5/8 OS N 3/4 OS N 7/8 OS N 1-1/8 OS Hand Expansion Valves Standard Type P4481 PRT SIZE ONN. IMENSIONS IN INHES WT (in.) Ori. ia. Mtg Hole trs (lb) 6291N 1/4 OS N 3/8 OS N 1/2 OS N 5/8 OS N 3/4 OS N 7/8 OS N 1-1/8 OS harging and Purging Valves Globe Standard Type P4482 PRT SIZE ONN. IMENSIONS IN INHES WT (in.) Mtg Hole trs (lb) 6231N 1/2 OS x 1/4 Flare N 3/8 OS x 3/8 Flare N 1/2 OS x 1/2 Flare N 5/8 OS x 5/8 Flare harging and Purging Valves Single Standard Type PRT SIZE ONN. (in.) IMENSIONS IN INHES WT ottom Side (lb) 6432N 3/8 OS 3/8 Flare P

17 REEIVER VLVES HENRY TEHNOLOGIES REEIVER VLVES Packed, ngle Type NGLE VLVE NON-K-SETING TYPE 776-1/4 Fare onnection P4484 NGLE VLVE K-SETING TYPE 779-, TYPE 783 E E P4485 Temperature Rating: 20 F to +300 F 500 PSI Maximum Working Pressure Forged rass ody PRT SIZE ONN. (in.) IMENSIONS IN INHES ottom Side E WT (Lb) Forged rass Non-ack-Seating /4 MPT 1/4 FL /4 OS /4 MPT 1/4 FPT /16 OS /4 MPT 3/8 FL /16 OS /8 MPT 1/4 FL /8 OS /8 MPT 3/8 FL /8 OS /8 MPT 1/2 FL /8 OS /2 MPT 3/8 FL /2 OS /2 MPT 5/8 FL /2 OS.91 Forged rass ack-seating /2 MPT 1/2 FL / /2 MPT 5/8 FL /2.69 Forged rass ack-seating* /8 OS /2 OS /8 OS /8 OS /8 OS /8 OS /8 OS *Furnished with 1/4-in. flare capped charging and testing connection above back-seat. HENRY TEHNOLOGIES PKE NGLE TYPE, HRGING N PURGING Forged rass ody, Plated lack Oxided Steel Stem and Molded Valox Seal ap, rass Flare aps. Temperature Rating: 20 F ( 29 ) to +300 F (+149 ). Maximum Working Pressure: 500 PSI, (35 Kg/cm 2 ) Valves Furnished isassembled to void Excessive Heating of Internal Parts uring razing. P4486 TYPE 927 NON-KSETING PRT SIZE ONNETIONS (in.) IMENSIONS (in.) ottom Side WT (Lb) /4 OS 1/4 Flare /8 OS 1/4 Flare /8 OS 3/8 Flare /2 OS 1/4 Flare /2 OS 3/8 Flare

18 SEL P VLVES HENRY TEHNOLOGIES SEL P VLVES ackseating esign Forged rass ody with Integral Mounting Flange, Plated Steel Stem; rass onnet and Molded Valox Seal ap. ackseating: an e Repacked Under Pressure. Temperature Rating: 20 F ( 29 ) to +300 F (+149 ) Maximum Working Pressure: 500 PSI, (35 Kg/cm 2 ) Recommended for Hot Gas Service or Other High Temperature pplications. PRT SIZE ONNETIONS (in.) IMENSIONS (in.) E F WT (Lb) /4 OS /8 OS /2 OS /8 OS TYPE 926 Mounting Flange 2 Holes E olt enters P4487 HENRY TEHNOLOGIES SEL P VLVES GLOE ESIGN Valve odies: ast ronze. ackseating: an e Repacked Under Pressure. Temperature Rating: 40 F ( 40 ) to +325 F (+163 ) Maximum Working Pressure: 450 PSI, (31 Kg/cm 2 ). TYPE 203 P4488 PRT SIZE ONNETIONS (in.) IMENSIONS (in.) WT (Lb) /8 OS /8 OS /8 OS /8 OS /8 OS /8 OS /8 OS

19 VLVES HENRY TEHNOLOGIES THREE-WY UL SHUT-OFF VLVES INLET P297-2 odies: 92 Series: Forged rass; 802 Series: Forged Steel; Painted. Maximum Working Pressure: 450 PSIG (31.5 Kg/m 2 ) Temperature Rating: 20 F ( 29 ) to +300 F (+149 ) Recommended for Use with Relief Valve Types. 802 Series is Suitable for Refrigerants Including mmonia and Other Industrial Fluids Non-orrosive to Steel. INLET E P4489 PRT SIZE ONNETIONS (in.) IMENSIONS (in.) E WT (Lb) 923 3/8 NPTF /2 NPTF /4 NPTF /2 NPTF /4 NPTF NPTF /4 NPTF

20 PRESSURE RELIEF VLVES HENRY TEHNOLOGIES PRESSURE RELIEF VLVES tmospheric, ngle & Straight-Thru Types rass onstruction Set and Sealed at the Factory; ll NPTF onnections are merican Standard ryseal Tapered Pipe Threads Valves are Stamped with atalog Number, Size, Pressure Setting, apacity and SME-UV National oard Symbol; RN Number and Flow rrow ll NPTF onnections are merican Standard ryseal Tapered Pipe Threads Positive Pressure Relief Suitable for Refrigerants 12, 22, 500, 502, 12, 134a, and Other Industrial Fluids Non-orrosive to rass, Monel, Steel and Teflon Temperature Rating: 40 F ( 40 ) to +225 F (+107 ) Orders Must Specify atalog Number, Pressure Setting, and Type of Refrigerant or Fluid With Which the Valve is to be Used; UV/N ertified Setting Range PSI. ontact Henry for Non-ertified Setting Range Information. Standard Settings re: 235 PSI, 300 PSI, 350 PSI, 400 PSI, 425 PSI, 450 PSI IMPORTNT: ORERS MUST SPEIFY PRESSURE SETTING. RNGE 150 to 450 PSI TMOSPHERI RELIEF VLVES PRT SIZE ONN. INLET IM/IN. ORIFIE I. WT (lb) /4 MPT /8 MPT NGLE RELIEF VLVES PRT SIZE ONN. IM./IN. ORIFIE WT Inlet Outlet I. (lb) 526E 3/8 MPT 3/8 FL E 1/2 MPT 5/8 FL STRIGHT-THRU RELIEF VLVES INLET Type 522 tmospheric P4490 PRT SIZE ONN. IM./IN. ORIFIE WT Inlet Outlet I. (lb) /4 MPT 3/8 FL /8 MPT 3/8 FL /8 MPT 1/2 FL /2 MPT 5/8 FL /2 1/2 MPT 3/4 FPT /4 3/4 MPT 3/4 FPT MPT 1 FPT RELIEF VLVE PITY RTINGS PRT STNR PRESSURE SETTING (psig) E E / / INLET Type 52 ngle INLET Type 523 & 524 Straight Thru P4492 P4491 SME N National oard ertified 673

21 RUPTURE IS SSEMLIES HENRY TEHNOLOGIES RUPTURE IS SSEMLIES 5525 & 5526 rass Series; 5626, 5627, 5628 and 5629 Stainless Steel Series Tested and ertified to SME Section VIII iv I Prevents Leakage or Weeping of Fs Through the Relief Valve Extra Gauge Port for Installation of a Pressure Switch to Warn of a Refrigerant Release aused by a System Malfunction Non-Fragmenting Rupture isc Rupture isc ssembly Factory Sealed 1/8" NPT 1/8" NPT INLET P4496 PRT Inlet MPT SIZE ONN. Outlet FPT RUPTURE IS SETTING 72 F PSI WT (lb) /8 3/ /8 3/ /8 3/ /8 3/ /2 1/ /2 1/ /2 1/ /2 1/ /2 1/ /2 1/ /2 1/ /4 3/ /4 3/ /4 3/ /4 3/ /4 3/ /4 1-1/ /4 1-1/ /4 1-1/

22 USE NO OIL MXINPUT 600 psi USE NO OIL MXINPUT 600 psi RUPTURE SSEMLY PRESSURE SWITHES/INITORS HENRY TEHNOLOGIES RUPTURE SSEMLY PRESSURE SWITH Type: irect ction lade ontact ontacts: Silver lloy, Gold Plated Set Point: Factory Set and Sealed Pressure Setting: 5 PSI Switch urst Pressure: 750 PSI Ratings: 4 MP - 24 V iaphragm: TEFLON Temperature Range: 40 F to +250 F onnector: 1/8-27 NPT Male Thread Terminals: METRI-PK, 1/4-in. lade ircuitry: Normally Opened ase: Steel over: Glass Reinforced Polyester Furnished with METRI-PK onnector and 10 ft of Wire NOTES: The addition of a Sentry Pressure Switch provides an inexpensive means of providing an electrical signal to warn of a refrigerant release caused by a system malfunction. n extra gauge port is provided on the Sentry Rupture isc ssembly for the switch Pressure Switch Part No.: SW56 P4497 P4497 HENRY TEHNOLOGIES RUPTURE SSEMLY PRESSURE INITOR ial: 1-3/8-in. (35 mm), White luminum ial with Red Marking ial: Maximum Working Pressure: 600 PSI ase: ISI 304 Stainless Steel Lens: Plexiglass, Watertight Pointer: ISI 304 Stainless Steel Socket: ISI 304 Stainless Steel mbient Temperature: 40 F/+150 F ( ) NOTES: The Pressure Indicator (Item ) can be used with our Sentry Rupture isc ssembly (Item ), which helps prevent leakage of both halocarbon and ammonia refrigerants by indicating whether the relief valve had discharged. The Sentry Rupture isc ssembly, as required by NSI/SME ode, provides a chamber between the rupture disc and the relief valve, and a connection to install the new pressure indicator. This arrangement permits a positive indication that the disc has ruptured and the relief valve has discharged. Item Pressure Indicator G15 USE NO OIL MXINPUT 600 psi P4498 P4499 Item The Sentry Rupture isc ssembly/relief Valve ombination is showninitsnormaloperatingconditionwithsystempressureonly under the Rupture isc. (See first pressure gauge.) USE NO OIL MX INPUT 500 psi NOTE: Relief valve, pressure gauge and pipe plug not included with Sentry Rupture isc ssembly. P4498 PRT G15 SIZE ONNETION 1/8-in. MPT, ack P

23 RUPTURE SSEMLY PRESSURE SWITHES/INITORS HENRY TEHNOLOGIES TRNSUER VLVE Forged rass Temperature Rating: 20 F ( 29 ) to +300 F (+149 ) Maximum Working Pressure: 500 PSI (35 kg/cm 2 ) onnector: 1/4-in. Flare ccess with Schrader ore Provides ccess to Systems and Mounting of a Transducer to Monitor Systems Performance Provides Schrader Valve Port for hecking Transducer Output with a Pressure Gauge Provides Isolation from System for Replacement of Transducer Suitable for Refrigerants and Other Industrial Fluids Non-orrosive to rass and Steel P4501 PRT SIZE ONN. IMENSIONS IN INHES WT (lb) Side ottom /8 FPT-1/4 FL 1/4 MPT