Specifications, Applications, Service Instructions & Parts. HCK1, HCK1W PISTON-TYPE CHECK VALVE ¾" thru 6" (20 thru 150 mm)

Transcription

1 Bulletin Specifications, Applications, Service Instructions & Parts HCK1, HCK1W PISTON-TYPE CHECK VALVE ¾" thru (20 thru 150 mm) d ¾" thru FPT, SW, WN, ODS for refrigerants Piston-Type Check Valve: HCK1 INTRODUCTION These flanged, heavy-duty, piston-type check valves control the flow of refrigerant. Valves open wide for flow in the direction of the arrow on the valve body. Valves close tight when flow reversals occur. The piston design minimizes pulsations. KEY FEATURES Valves open when inlet pressure exceeds outlet pressure (1 psid [.07 bar] minimum), thereby lifting the piston/seat assembly and allowing flow through the valve. When inlet pressure and outlet pressure are equalized, the weight of the piston/seat assembly causes the valve to close. If outlet pressure exceeds inlet pressure, the outlet pressure acting on top of the piston/seat also helps seat the valve closed. Also available, Type HCK4 in-line check valves and Type SCK combination stop/check valves; contact Hansen ADVANTAGES This normally closed valve requires very little pressure drop to operate. Valve sizes ¾" thru 1¼" have spring-assisted closing. Valve sizes 1½" thru have a special, spool-type, dirt-resistant piston/ seat. A manual opening stem allows positive opening during servicing or troubleshooting the system. The flange-to-flange dimension and flange pattern are the same as the Parker R/S allowing this valve to be dropped in without main line piping changes (exception: 1¼"). APPLICATIONS The HCK1 piston-type check valve prevents reverse flow of refrigerant in liquid, discharge, suction, and hot gas lines. It is an ideal valve where constant pulsating of gas or liquid is present, or where a manual opening of the valve is desirable. This valve is suitable for ammonia, R22, R134a, and other common refrigerants.

2 MATERIAL SPECIFICATIONS Body: ¾" thru : Ductile iron ASTM A536. & : Cast steel : ¾" thru 1¼": Stainless steel with Teflon seat 1½" thru : Ductile iron, ASTM A536 Closing Spring: Stainless steel (¾" thru 1¼" only) s: Nonasbestos, graphite composite Stem: Plated steel : Steel Stem Seal: O-ring plus graphite composite packing Companion s: Forged steel Safe Working Pressure: 400 psig (27 bar) Operating Temperature: 25F to +250F ( 32 to +121 C) INSTALLATION Protect the interior of the valve from dirt and moisture during storage and installation. The valve must be installed upright in a horizontal line. The arrow on the valve body should be in the normal direction of refrigerant flow. The system should be free of dirt, weld slag, and rust particles. Install the valve in an accessible location for servicing. Do not install a check valve at the inlet of a solenoid valve or regulator with electric shut-off. Do not install a check valve at the inlet of an outlet regulator where liquid may be trapped between the valves. Check valves in general, when installed, should be at the outlet of control valves to avoid trapping refrigerant between the valves. SIZING The same care should be taken when sizing check valves as with any other type of control valve. Check valves should be sized so that the valve is fully open under all normal operating conditions. Also, the check valve port size is not always the same as the line size. This is particularly true for gas flow in compressor discharge lines and hot gas lines. Under some conditions, the port size of a properly-selected check valve can be one or two sizes smaller than the line. The pressure drop across the HCK1 check valve should normally be 2 to 5 psi under full load conditions. In addition, the pressure drop across the check valve at normal minimum load should be determined. For the Hansen HCK1 check valve, a minimum of 1 psi at minimum load is required to ensure that the valve is fully open during all normal flow conditions. CAPACITIES (Tons) (1 Ton= 12,000 Btu/hr= kw= 3042 kcal/hr) REFRIG. R717 R22 2 psi = 0.14 bar 5 psi = 0.35 bar 1 U.S. GPM (gallons per minute) = m 3 /hr Discharge line capacities based on +86F (+30 C) condenser, +140F (+60 C) discharge, and +15F ( 9.4 C) evaporator. Compressor sideport capacities based on +20F ( 6.7 C) economizer and +86F (+30 C) condensing. Liquid line capacities based on +20F ( 6.7 C) liquid and +5F ( 15 C) evaporator, with no flashing through valve. To convert to +86F (+30 C) liquid, multiply values in table by 0.9. To convert R22 capacities to R134a, multiply tons in table by 0.92 (accuracy within 8%). GPM correction factors for temperatures between 40F ( 40 C) and +40F (+4.4 C) are negligible. A PPLICATIONS PORT SIZE (mm) Discharge Line Compressor Sideport Liquid Line TONS GPM Discharge Line Compressor Sideport Liquid Line Cv (Kv) TONS GPM P ¾" (32) (32) 1¼" (32) 2 1½" (40) (50) 2½" (65) (80) (100) 2 psi (125) 5 (150) psi psi psi psi psi psi psi psi psi psi psi (7) 10.5 (9) 16.3 (14) 47 (40) 55 (47) 89 (76) 126 (108) 276 (236) 350 (300) 450 (385)

3 TYPICAL APPLICATIONS DISCHARGE LINE COMPRESSOR SIDEPORT INTERMEDIATE PRESSURE GAS TO COMPRESSOR SUCTION HCK1 PISTON-TYPE CHECK VALVE ECONOMIZER COOLER PUMP DISCHARGE LINE TRANSFER SYSTEM PUMP ACCUMULATOR VENT/BYPASS LINE LIQUID RELIEF HCK1 PISTON-TYPE CHECK VALVE The above are schematic drawings of fictional refrigeration systems to show Hansen product applications in a system. These drawings should not be used for design or construction. 3

4 INSTALLATION DIMENSIONS ¾" thru (20 mm thru 100 mm) & (125 mm & 150 mm) 20.40" (518 mm) PORT SIZE (mm) ¾ ", (20), (25) 1¼" (32) 1½ ", (40), (50) 2½" (65) (80) (100) (125) (150) HCK1 -to-flange dimensions (L) are the same as the Parker R/S Type CK1, except 1¼",, and. *L1 is the flange face-to-face dimension. DIMENSIONS (mm) L H 1 H 4 FPT, SW WN, ODS 4.2 (107) 4.2 (107) 7.1 (182) 8.0 (205) 8.38" (213) 9.88" (251) 12.1 (308) 12.1 (308) 4.30" (108) 4.30" (108) 5.3 (136) 6.10" (155) 6.5 (167) 7.38" (187) 14.3 (364) 14.3 (364) 8.20" (208) 8.20" (208) 12.39" (315) 13.0 (330) 15.38" (391) 17.0 (432) 8.9 (227) 8.9 (227) 13.39" (340) 14.0 (356) 16.40" (417) 20.5 (521) L 1 * L W ** " (157) 6.19" (157) 9.88" (251) 9.88" (251) 12.2 (311) 14.1 (359) 7.20" (183) 7.20" (183) 10.89" (277) 11.0 (280) 13.38" (340) 15.0 (381) 4.50" (114) 4.50" (114) 4.50" (114) 5.6 (143) 6.50" (165) 8.0 (205) 12.7 (324) 12.7 (324) **W dimension is the maximum width of the valve. 4

5 HCK1 PARTS LIST, ¾" thru 1¼" (20 mm thru 32 mm) ITEM Q TY PART NO. Kit ¾", Kit 1¼" Above kits consist of: 1a xxpiston/sea t ¾ ", b xx 1¼" xxclosing Spring xx O-ring, Lower xx O-ring, Upper Kit ¾",, 1¼" Above kit consists of: 3 xx O-ring, Lower xx O-ring, Upper xxstem O-ring xxstem Washer xxpackin g xxpacking Nut xxseal Cap O-ring xx xxseal Cap xxseal Cap O-ring xxstem a Body ¾ ", b Body 1¼" (various) 2 FACTOR Y 16 Bolt ( 5 /8"-11 x 2 3 /) Nut ( 5 /8"-11)

6 HCK1 PARTS LIST, 1½" thru (40 mm thru 100 mm) ITEM Q TY PART NO. Kit 1½", Kit 2½" Kit Kit Above kits consist of: 1a xx 1½ ", b xx 2½ ", c x x a xx 1½ ", b xx 2½ ", c x x Kit 1½", Kit 2½" Kit Kit Above kits consist of: 2a xx 1½ ", b xx 2½ ", c x x a xxback-up Washer 1½",, 2½ ", b x xback-up Washer a xxstem O-ring 1½",, 2½ ", b x xstem O-ring a xxstem Washer 1½",, 2½ ", b x xstem Washer a xxpacking 1½",, 2½ ", b x xpacking a xxpacking Nut 1½",, 2½ ", b x xpacking Nut a xxseal Cap O-ring 1½",, 2½ ", b x xseal Cap a xx 1½ ", b xx 2½ " c x x d x x ITEM 9a Stem 1½,, 2 9 b tem 9 c tem 10a Seal Cap 1½",, 2½, 10b eal Cap 11a 1½, 11b 2½, 11c over 12a Bolts 1½, 12b Bolts 2½, 12c over Bolts 13a ody 1 13b ody 13c ody 2 13d ody 13e ody 15 lange (various) 16a Bolt 1½ ", ( 5 /8"-11 x 3 1 /4 ) 16b Bolt 2½ ", ( ¾" -10 x 3¾ ) 16c Bolt ( 7 /8-9 x ) 17a Nut 1½ ", ( 5 /8-11) 17b Nut 2½ ", ( ¾ -10) 17c Nut ( 7 /8-9) Q TY PART NO. " ½" S S " S " " C " " C B ½" B B ½" B B F 2 FACTOR Y " " " " " "

7 HCK1W PARTS LIST, & (125 mm & 150 mm) ITEM a b QTY PART NO 1 x x x O-ring, Inner, & x O-ring, Outer, & xback-up Washer xstem Seal O-ring xstem Washer xpackin g xpacking Nut xseal Cap xstem xseal Cap x x Bolts a x Body b x Body

8 SERVICE AND MAINTENANCE Failure to Close: The manual opening stem is turned in, mechanically holding the piston/seat open. Dirt may be lodged between the piston/seat and the valve piston wall. Failure to Open: The pressure difference is not high enough. Inlet pressure must be at least 1 psi above outlet pressure. Adjacent shut-off valves or control valves are not open. Dirt may be lodged between the piston/seat and valve piston wall. Manual Operation: If it is necessary to manually hold open the HCK1 valve, remove the seal cap cautiously. There may be a small amount of refrigerant trapped in it. Turn the manual opening stem inward (clockwise) as far as possible. The piston/seat is then mechanically held open. The valve cannot close until the manual opening stem is turned out (counter-clockwise). If it is necessary to remove or disassemble the valve for servicing, be sure it is completely isolated from the refrigeration system and all refrigerant is removed (pumped out to zero pressure). Be sure to follow refrigeration system safety procedures and read the Caution section in this bulletin. To inspect valve interior, slowly loosen the screwed cover or four cover bolts equally, being careful to avoid any refrigerant which may still remain. Remove the piston/ seat. Then clean and inspect for burrs and damage to the seating surfaces. Slight marks and burrs can often be removed by hand with emery paper or by power lapping. Damaged parts should be replaced. Lightly lubricate the main valve interior bore with refrigerant oil, and install the piston/seat and closing spring (a closing spring is used in ¾" - 1¼" valves only). Replace the cover, gasket and bolts (1½" - ). Carefully check the entire valve for leaks before restoring the valve to service. CAUTION Hansen valves are only for refrigeration systems. These instructions and related safety precautions must be completely read and understood before selecting, using, or servicing these valves. Only knowledgeable, trained refrigeration mechanics should install, operate, or service these valves. Stated temperature and pressure limits should not be exceeded. The valve cover or pilot line should not be removed from valves unless the system has been evacuated to zero pressure. See also Safety Precautions in the current List Price Bulletin and the Safety Precautions Sheet supplied with the product. Escaping refrigerant might cause injury, particularly to the eyes and lungs. ORDERING INFORMATION, PISTON-TYPE CHECK VALVES PORT SIZE (mm) STD FLANGE STYLE AND SIZES CONNECTIONS AVAILABLE SW, WN, FPT ALSO ODS STD ¾"x ( 20) ¾", 1¼" 7 /8" x ( 25) ¾", 1¼" 1 1 /8" 1¼"x ( 32) * 1¼", ¾" 1 3 /8" 1½"x ( 40) 1½" 1 5 /8" x ( 50) 1½" 2 1 /8" 2 ½"x ( 65) 2½" 2 5 /8" x ( 80) 3 1 /8" x ( 100) 4 1 /8" x ( 125) ** BW x ( 150) ** BW * ¾",, and 1¼" valves are 2-bolt design. ** & are integral butt weld only, Type HCK1W. To Order: Specify Type HCK1 (or HCK1W), port size, flange connection style and size. TYPICAL SPECIFICATIONS Piston-type check valves shall be ductile iron or steel bodied, normally closed, with a manual opening stem, as manufactured by Hansen Technologies Corporation or approved equal. OTHER PRODUCTS Ammonia Pressure-Relief Valves Gauge, Purge, and Needle Valves Shut-off Valves Expansion Valves (Regulators) Refrigerant Solenoid Valves Refrigerant Pressure Regulators Small Pressure Regulators Refrigerant Check Valves Strainers Gas-Powered Valves Refrigerant Float Switches Float Regulators (High Side) Refrigerant Liquid Pumps AUTO-PURGER Non-condensable Gas Purgers Vari-Level Adjustable Level Controls Techni-Level Transducer Probes Frost Master Defrost Controllers SEE-LEVEL Refrigerant Liquid Indicators WARRANTY Hansen valves are guaranteed against defective materials or workmanship for one year F.O.B. factory. No consequential damages or field labor is included. Teflon is a registered trademark of DuPont High Grove Boulevard Burr Ridge, Illinois USA Tel: (630) Fax: (630) Toll: (800) Hansen Technologies Corporation