NEECO INDUSTRIES INC. INSTRUCTION MANUAL 7 1/16 10K SLAB GATE BODY

Size: px
Start display at page:

Download "NEECO INDUSTRIES INC. INSTRUCTION MANUAL 7 1/16 10K SLAB GATE BODY"

Transcription

1 INSTRUCTION MANUAL 7 1/16 10K SLAB GATE BODY

2 INTRODUCTION The NF-700 type gate valves provided by Neeco Industries are full-bore through conduit non-rising stem manually (w/ball screw) operated valves. The NF-700 model has a slab gate with floating seats thus offering a true metal-to-metal seal that is very reliable. The ball-screw mechanism on the valve provides for low operating torque and is widely accepted due to its ease of operation. The NF-700 valve has a proven and tested design from years of use in the field. Neeco Industries has prepared this Instruction Manual to assist in the assembly, installation, operation and maintenance of the product. If you need more information or assistance, you should contact: Neeco Industries, Inc Emmett Road Houston, Texas Tel: Toll Free: Fax:

3 SCHEMATIC DIAGRAM

4 BILL OF MATERIAL Valve Model NF - 700, 7 1/16 10K, FE,/Ball Screw EE Trim Item # Description Qty Mat l 1 Handwheel 34 1 Ductile Iron 2 Bonnet Cap 1 AISI /8 Injection Fitting 2 Buy-out 4 O Ring 178 (internal) X Buy-out 5 Needle Bearing 2 Buy-out 6 Upper Stem Protector 1 WCB 7 Indicating Adapter 1 AISI 316 SS 8 Bearing Nut 1 ASTM B 62 9 O Ring 73 (internal) X Nitrile Rubber 10 Bearing Housing 1 AISI Packing Gland 1 AISI a Stem Packing 2 PTFE + Viton 12 Studs (1 7/8-8UNC) 24 AISI Heavy Hex Nut (2 15/16 ) 24 AISI Upper Bonnet 1 AISI Upper Stem/Ball Screw 1 Assy Parts 316 SS 16 Bonnet Gasket SS 17 Gate 1 AISI Colmonoy# 5 18 Junk Ring 1 Nitrile Rubber 19 Seat Seal Ring 4 PTFE+Graphite 20 Retainer Plate 2 AISI Valve Body 1 AISI Name Plate 1 AL 23 Name Plate Screws 4 Buy-out Part 24 1/2 NPT Grease Fitting Valve 2 Buy-out Part 25 Gate Guide 2 CS 26 Lower Stem 1 AISI 410 SS 27 Lower Stem Protector 1 WCB 28 Lower Bonnet 1 AISI Seat SS + Colmonoy # 5

5 TEMPERATURE RATING NOTE: For special applications involving different sizes or pressure ratings, temperatures, materials, etc., please contact Neeco Industries customer service.

6 DESCRIPTION AND FEATURES The NF-700 valve is a full-bore through conduit valve designed to meet the requirements of API-6A. It is made with standard flanged outlets but can be modified to have studded outlet configurations. Standard features of the Neeco gate valve are: 1. Minimized operating torque. These valves are built with a ball screw mechanism and have a lower stem which also helps in indicating the gate position. 2. Manufactured to have a metal-to-metal sealing at the gate-to-seat area and designed for dependable sealing by incorporating a simplified slab gate and seat assembly to seal in both directions. This feature helps to reduce the number of parts and simplify field service as well. 4. The stem packing used is of non-elastomeric material for low coefficient of friction and is a pressure energized seal to withstand severe temperatures and fluids. 5. Back seating feature of the upper stem and lower stem allows either stem packing to be replaced if necessary while the valve is under pressure. 6. For safety, these valves are provided with grease fittings located on the downstream side of the upper stem and lower stem back seat shoulders. No lubrication ports extend directly into the valve cavity. 7. The BX-Style metal bonnet gasket used in these valves provides pressure-energized seal between the valve body and bonnet.

7 OPERATION 1. The gate should be completely opened or closed when installation or shipping is to be done. When the valve is to be stored, the gate should be completely open, thus preventing damage to the sealing mechanism. 2. The molybdenum disulfide coating shall not be removed from the internal parts as the coating serves as a lubricant and corrosion inhibitor. 3. Valve OPENs with the counterclockwise turning of hand wheel and clockwise turning CLOSEs the valve. A 1/4-1/2 counterclockwise turn should be given after closing so as to ensure that the slab gate is floating and sealing. The required input torque may increase for the last few turns if a pressure differential builds across the gate. 4. The valve must be in a partially open position when hydrostatic test is to be conducted on the valve. At the time of testing the valve in closed position, i.e. performing seat test, care should be taken that the recommended working pressure is not exceeded. 5. When servicing on the stem bearing is to be done, the valve should not be in service condition. Note: When required to bleed pressure from the bore, there may be trapped pressure in the cavity when the valve is in the open or closed position. The valve may be cycled or temporarily held in the half open position to relieve this pressure. SIZE NO. OF REVOLUTIONS TORQUES BEFORE CRACKED OPEN 7 1/16-10K 17 ¼ 180 ft-lbs

8 LUBRICATION 1. The maximum API working pressure should not be exceeded, which can be referred to on the nameplate. 2. During the lubrication of the seats and/or body, the valve must be partially open to allow the grease to spread evenly. 3. Stem bearing is to be lubricated through the 1/2 NPT grease fitting provided on the bonnet. Any No. 3 grease of good grade is recommended. 4. The maximum allowable API test pressure must not be exceeded when lubricating the seats. NAMEPLATE All Neeco Industries valves come with a nameplate attached to them. They are located in the center of the body area. These plates ensure that the specified design has been followed along with strict QC stipulations set by the industry.

9 PERIODIC MAINTENANCE Neeco NF-700 gate valves do not require the injection of lubricants or sealants to operate effectively or seal properly. But it is highly recommended to periodically lubricate the valve to increase the life and serviceability and also to prevent it from corrosion and excessive wear and tear. Tools for Maintenance 1. Grease pump with adapters and coupling (Please contact Neeco Industries if you don t have proper adapters or couplings) Fig 1 Grease pump with adapter and pistol. 2. Pressure releasing tool Fig 2. Bleeding Valve Neeco 7 1/16-10K Slab gate valves are supplied with 1/2 NPT body fitting connection.

10 TESTING THE EFFECTIVENESS OF THE BACK SEAT The valves with 10,000 psi WP and below use an NPT thread type of grease fitting, see Figure 3. Figure 3. Grease fitting for 10,000 psi WP and below 1. Remove the cap on the grease fitting. (Refer to Figure 8) 2. Trip the ball in the grease fitting check valve by inserting a 1/8" diameter by 3/4" long pin into the run of the fitting. 3. Replace the cap slowly until the ball in the fitting is unseated and the pressure trapped behind the stem back seat is released. GREASE FITTING REPLACEMENT The upper and lower grease fittings can be replaced while the valve is under pressure only if they are isolated by an effective back seat seal, which has been verified. Replacement of the grease fitting under pressure should be done only when all options of isolating the valve from pressure are exhausted. NOTE: When required to bleed pressure from the bore, there may be trapped pressure in the cavity when the valve is in the open or closed position. The valve may be cycled or temporarily held in the half open position to relieve this pressure.

11 1. Preparation: a. If the valve is under pressure, both grease fittings cannot be replaced at the same time. The grease fitting on the bonnet can be replaced only if the upper stem passes its back seat test. Similarly, the grease fitting near the stuffing box or bottom of the valve can be replaced only if the lower stem passed its back seat test. b. If the valve was isolated from pressure, use the grease fittings to check and release any pressure trapped inside the valve cavity. 2. Remove the defective grease fitting. 3. Remove the cap from the new grease fitting. If the grease fitting has NPT threads, valves rated at 10,000 psi and below, apply Teflon thread seal tape or thread sealant according to the manufacturer s instructions. If the grease fitting has a straight thread, valves rated at 15,000 psi and above, do not use Teflon tape or thread sealant. Caution: Installing the fitting with the cap in place prevents the fitting from properly seating and could cause damage to the cap. 4. Install the new grease fitting. 5. Install and tighten the cap on the grease fitting. 6. Un-back seat the appropriate valve stem.

12 GATE AND SEAT REPLACEMENT The valve must be isolated from pressure before the gate and seat can be replaced. Note: When required to bleed pressure from the bore, there may be trapped pressure in the cavity when the valve is in the open or closed position. The valve may be cycled or temporarily held in the half open position to relieve this pressure. I. GATE AND SEAT REMOVAL 1. Isolate the valve from pressure. Release the cavity pressure by bleeding through grease fittings from Top & Bottom bonnets. 2. Close the valve by turning the hand wheel clockwise until it stops, then back off approximately 1/4 to 1/2 turn. 3. Support the bonnet and remove the bonnet nuts 4. Pull the bonnet assembly (along with lower stem) away from the valve body until it clears the bonnet studs. Place the bonnet assembly to the side to disengage the T-slot connection between the upper stem and the gate. Unscrew the lower stem to remove the lower stem. 5. Remove the bonnet gasket to inspect it and the seal groove. If the seal grooves are damaged, contact Neeco for repair. 6. Remove the retainer plates, gate guides, seats and seat seals from both sides. 7. Inspect the gate & seats, seat seals, retainer plates, gate guides, seat pockets of the valve body. 8. Assemble the new gate, lower stem and stem packing. II. GATE AND SEAT INSTALLATION 1. Flush the body cavity thoroughly with a suitable solvent and wipe clean with a rag. Ensure that the body cavity is clean. 2. Apply a thin coat of grease to the seat area inside the body cavity, gate and the seats. 3. Install the two seat seals into the face grooves on each seat. Install the seats into the body seat pockets with the seat seals facing the mating seat pocket. 4. Install Retainer Plates, Gate Guides in the valve cavity.

13 5. Install the gate into the cavity between the seats and keep the gate T slot above the body face for ease of bonnet installation. 6. Apply a thin film of grease onto the new gasket and the ring groove. Install the new gasket into the groove on the body. 7. Turn the hand wheel counterclockwise to extend the valve stem. Raise the bonnet toward the valve. Align and connect the valve stem and gate at the T-slot connection, then push the bonnet down onto the bonnet studs, while turning the valve hand wheel clockwise slowly. 8. Tighten four evenly spaced bonnet nuts with hand to prevent the bonnet from rising away from the valve body. 9. It is not recommended to tighten nuts without applying thread compound to stud and nuts. Install and tighten all the bonnet nuts evenly to the recommended torque using a star pattern. The bonnet face should fully contact the body face. Few suggestions are given below on thread compounds and torque values for tightening the stud size 1 7/8-8UNC & 2 15/16 Heavy Hex Nut used on this valve. Recommended Torque for Studs Thread Compound Molybedenum Disulfide Moly Graphite Recommended Torque 2775 ft-lbs 3460 ft-lbs

14 ASSEMBLY INSTRUCTIONS For ease and productivity, we have included the assembly instructions for the NF- 700 valve to ensure a comprehensive understanding of the purchased product for the customer. I. PARTS VIEW 1. Aggregate View of Internal Parts (excluding Bonnet components) 2. Bonnet Seal Rings (Upper/Bottom)

15 3. Seats w/seals (Note: Two seal areas on each seat) 4. Gate Guides

16 5. Top Bonnet (Note: Top-Bonnet has external threads) 6. Aggregate View of Top-Bonnet Internal Parts (Note: (2) Spring-Loaded Packing)

17 7. Ball Screw Assembly

18 II. ASSEMBLY PROCEDURES A. PRE-ASSEMBLY AND BOTTOM-BONNET 1. Insert studs onto either side of valve body by hand and then snug tight with wrench. 2. Grease and place (1) Bonnet Seal Ring on the groove area atop the valve body.

19 3. Place bottom bonnet (Stem protector attached) onto the valve body, carefully aligning the bolt holes and the studs. (Note: Bottom bonnet has internal threads). 4. Tighten down the nuts (with wrench) and then torque to 6,000 lbs. 5. Carefully turn over the valve body with bottom bonnet underneath (open end up).

20 B. TOP-BONNET ASSEMBLY 1. Insert (1) spring loaded packing onto threaded side of top bonnet, as shown in the picture. 2. Screw gland packing onto threaded side of bonnet and tighten.

21 3. Grease threaded stem (top-bonnet stem) and insert threaded side first into non-threaded end of bonnet, gently tapping the stem until about 1 remaining. Leave clearance to attach gate to stem block area. 4. Place the spacer (black) onto the threaded side of the bonnet, place the bearings on top of the spacer and install the ball screw operator (Note: To ensure ball screws stay in place, carefully screw bottom portion)

22 5. Insert the stem pin onto bottom portion of stem before tightening down the ball screw on the top bonnet, Place ball bearings over the ball screw portion, and screw the bearing cap onto the bottom.

23 6. Fully Assembled Top Bonnet

24 C. VALVE ASSEMBLY 1. Remove any debris and clean both seat pocket areas of the valve body. 2. Insert the inner and outer Teflon seals onto each seat, apply a generous amount of grease and install both seats (Teflon side out) in the seat pocket area of the valve body.

25 3. Place gate guides over the inserted seats on the valve body. 4. Insert T-Slot gate into the portion of the stem jutting out from the top bonnet and grease the gate.

26 5. Grease and place the upper bonnet seal ring (Note: Upper/Bonnet BSR are identical) onto valve body. 6. Take the non-threaded stem (bottom-bonnet stem) and fit the T portion onto the bottom part of the T-slot gate attached to the top bonnet, carefully place the fully-assembled top bonnet onto the valve body

27 7. Insert studs, insert nuts and torque down nuts to 6,000 lbs.

28 8. Place valve horizontal and remove the stem protector from bottom bonnet Insert (1) spring loaded packing,

29 Insert back cap (white) all the way into the bonnet, and screw back the stem protector.

30 DRIFT/HYDRO-TEST/GREASE 1. Drift test the fully-assembled valve by placing the drift plug through the bore area of the valve. 2. Place test flanges on each side of valve flanges with 3 to 4 studs and nuts. Note: Turn the valve to half-open position for purposes of conducting shell test prior to attaching both test flanges.

31 3. Insert a BX-156 gasket between each side of the valve and test flange before inserting all the studs/nuts and fully tightening with an impact gun 4. Shell Test: (PSL-3 Requirements) a. Insert two hoses, on each test flange, to conduct shell test.

32 b. Pressure up to 15,000psi for 3 minutes bleed off the pressure until zero, and close pressure release tool. Raise the pressure back up to 15,000psi for 15 minutes bleed off the pressure until zero. Close the pressure release tool and the valve. (Note: PSL-3 requires two separate tests at different intervals). c. If there is no indication of leakage during the holding periods, the valve is acceptable to PSL-3 requirements.

33 5. Seat Test: (PSL-3 Requirements) a. With the valve closed, pressure up to 10,000psi for 3 minutes, open the valve and bleed off the pressure until zero. Close the valve and the pressure release tool. Pressure up to 10,000psi for 15 minutes, open the valve and bleed off the pressure until zero. Close the valve and the pressure release tool. b. Switch the sides of your flow and pressure release connections, bleed off the new pressure release side and conduct two seat tests identical to 5(a) above on the new flow side. c. If there is no indication of leakage during the holding periods, the valve is acceptable to PSL-3 requirements. 6. Once the valve has been fully tested and the pressure is down to zero, loosen each of the test flanges with an impact gun and remove them from the valve.

34 7. Grease the flange areas of the valve. The valve is now ready for shipping.

Valveworks USA Operation and Maintenance Booklet Model FC

Valveworks USA Operation and Maintenance Booklet Model FC Operation and Maintenance Booklet Model FC MODEL FC 3000, 5000, 10000, & 15000 W.P. FLOATING SLAB GATE VALVES 1 13/16-2 1/16-2 9/16-3 1/16-4 1/16 BOOKLET APPROVED BY: INTRODUCTION In appreciation to you

More information

VALVEWORKS USA OPERATION AND SERVICE MANUAL FOR MODEL FC GATE VALVES MODEL FC PSI W.P FLOATING SLAB GATE VALVES

VALVEWORKS USA OPERATION AND SERVICE MANUAL FOR MODEL FC GATE VALVES MODEL FC PSI W.P FLOATING SLAB GATE VALVES OPERATION AND SERVICE MANUAL FOR MODEL FC GATE VALVES MODEL FC 3000-15000 PSI W.P FLOATING SLAB GATE VALVES INTRODUCTION In appreciation to our customer for purchasing our product, we have prepared this

More information

OPERATION & MAINTENANCE MANUAL API 6A SLAB GATE VALVE AAS-013 REV C

OPERATION & MAINTENANCE MANUAL API 6A SLAB GATE VALVE AAS-013 REV C OPERATION & MAINTENANCE MANUAL API 6A SLAB GATE VALVE AAS-013 REV C TABLE OF CONTENTS I. Introduction............................................. 3 II. Installation and Operating Instructions..............................

More information

NEECO PRODUCT CATALOGUE (FLN/FLSN)

NEECO PRODUCT CATALOGUE (FLN/FLSN) PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY: The copy, reproduction, distribution, publication, display, modification, creation of derivative works, transmition, of any content on this catalog

More information

PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance

PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance ACECO Valve P.O. Box 9 Mounds, Oklahoma 74047 PV4 - Compact Shut Off Style Pig Valve IOM - Installation, Operation & Maintenance Doc. No.: IOM-PV4-.0 Date: 6/0-00 Revision: A Contents: Installation Operation

More information

TRUNNION MOUNTED BALL VALVE INSTALLATION, MAINTENANCE, & REPAIR MANUAL

TRUNNION MOUNTED BALL VALVE INSTALLATION, MAINTENANCE, & REPAIR MANUAL TRUNNION MOUNTED BALL VALVE INSTALLATION, MAINTENANCE, & REPAIR MANUAL Corporation 3245 S. Hattie Oklahoma City, Oklahoma 73129 Telephone: (405) 677-3321 Fax: (405) 677-3917 Email:Balon@balon.com www.balon.com

More information

MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody

MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody MEMORY SEAL BALL VALVES MAINTENANCE MANUAL 2 12, Class 150 & 300, Regular Port, Flanged Unibody I INTRODUCTION These rugged, versatile, high performance, regular port, ball valves meet all requirements

More information

The Solution For The Valve Problems Plug Valves

The Solution For The Valve Problems Plug Valves www.3zvalve.com The Solution For The Valve Problems Plug Valves CONTENTS The Solution For The Valve Problems Plug Valves DBB Group Double Block & Bleed Valves 5 Soft Seated Group Sleeved Valves 23 Lined

More information

CV Control Valves Installation and Operation Manual

CV Control Valves Installation and Operation Manual CV1500 - Control Valves Installation and Operation Manual 652-EN Overview Warning: This bulletin should be used by experienced personnel as a guide to the installation of the Armstrong CV1500 Control Valve.

More information

Wellhead Valves. DHV Industries,Inc. DHV Valve Company Inc.

Wellhead Valves. DHV Industries,Inc. DHV Valve Company Inc. DHV Industries,Inc. 3451 Pegasus Drive, Bakersfield. CA 93308 U.S.A. Call TollFree: (887) DHV-USA1 Phone: (661) 392-8948 Fax: (661) 392-8947 E-mail: sales@dhvindustries.com Website: www.dhvindustries.com

More information

Type MR105 Direct-Operated Pressure Reducing Regulators

Type MR105 Direct-Operated Pressure Reducing Regulators Instruction Manual Form 5874 Type MR105 December 2014 Type MR105 Direct-Operated Pressure Reducing Regulators Contents Introduction...2 Specifications...2 Principle of Operation...3 Installation...4 Overpressure

More information

OPERATION AND MAINTENANCE MANUAL 2-66 SERIES 2500 RESILIENT WEDGE GATE VALVE

OPERATION AND MAINTENANCE MANUAL 2-66 SERIES 2500 RESILIENT WEDGE GATE VALVE OPERATION AND MAINTENANCE MANUAL 2-66 SERIES 2500 RESILIENT WEDGE GATE VALVE INDEX SERIES 2500 DUCTILE IRON RESILIENT WEDGE GATE VALVE OPERATION and MAINTENANCE MANUAL. OPERATION AND MAINTENANCE Operation,

More information

Series A Floating Ball Valve Installation, Operation & Maintenance XXXX - X X X X X X X. Base Part Numbers. Trim Option Suffix Code

Series A Floating Ball Valve Installation, Operation & Maintenance XXXX - X X X X X X X. Base Part Numbers. Trim Option Suffix Code Series A Floating Ball Valve Installation, Operation & Maintenance Base Part Numbers RATING 1 FP 2 RP 2 FP 3 RP 3 FP 4 RP 4 FP 1000 1102 1103 1104 1106 1105 1107 1500 1151 1152 1153 1154 1156 1155 1157

More information

Mogas MVP Installation, Operation And Maintenance Manual

Mogas MVP Installation, Operation And Maintenance Manual Mogas MVP Installation, Operation And Maintenance Manual Congratulations on your purchase of a Mogas Valve For Power This pamphlet is intended to provide complete information on installation, operation,

More information

Val-Matic QuadroSphere Trunnion Mounted Ball Valve

Val-Matic QuadroSphere Trunnion Mounted Ball Valve Manual No. QS-OM1-1 Val-Matic QuadroSphere Trunnion Mounted Ball Valve Operation, Maintenance and Installation Manual INTRODUCTION... 2 RECEIVING AND STORAGE... 2 INSTALLATION... 2 DESCRIPTION OF OPERATION...

More information

Expanding & Slab Gate Valves

Expanding & Slab Gate Valves Global Energy Market Solutions CAST / FORGED BODY Expanding & Slab Gate Valves For oil and natural gas wellhead, flowline, manifold, fracture or other critical service applications requiring operating

More information

Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual Installation, Operation, and Maintenance Manual API 6D Piston Check Valve - IOM: Installation, Operation and Maintenance Manual 1/16 Table of Contents 1 INTRODUCTION... 3 1.1 SCOPE... 3 1.2 DISCLAIMER...

More information

BC, BCF, BFF, BWF & BHF. Chokes

BC, BCF, BFF, BWF & BHF. Chokes BC, BCF, BFF, BWF & BHF Chokes 2 AOP 2/2012-SWP-D BR-AOP-BC/BCF/BFF/BWF/BHF-CHOKES-01 CAMERON TECHNOLOGIES: AOP CHOKES AOP chokes are general purpose chokes suitable for a host of applications within the

More information

Fig.01 Fig.02 Fig.03. Disassembly & Reassembly Instructions SBV-HP - Page 3

Fig.01 Fig.02 Fig.03. Disassembly & Reassembly Instructions SBV-HP - Page 3 M12A14 WITH FLOATING BACKSEAT 3 Fig.01 Fig.02 Fig.03 Disassembly & Reassembly Instructions SBV-HP - Page 3 M12A14 WITH FLOATING BACKSEAT 3 1. Caution, before any attempt is made to disassemble, verify

More information

KE Series. Through Conduit, Double Expanding Gate Valves

KE Series. Through Conduit, Double Expanding Gate Valves KE Series Through Conduit, Double Expanding Gate Valves The KE Series is an advanced API 6D designed gate valve that provides a tight mechanically activated seal. It has double sealing, bi-directional

More information

MODEL FM4 (HANDWHEEL OPERATED) SERVICE AND OPERATION MANUAL

MODEL FM4 (HANDWHEEL OPERATED) SERVICE AND OPERATION MANUAL MODEL FM4 (HANDWHEEL OPERATED) SERVICE AND OPERATION MANUAL Page 1 INTRODUCTION In appreciation to our customer for purchasing our product, we have prepared this Operation Manual to assist you in the Operation,

More information

Double Block & Bleed Plug Valves

Double Block & Bleed Plug Valves Double Block & Bleed Plug Valves ASME Class 150 & 300 50 mm to 750 mm (2 to 30 ) API 6D L&T Valves L&T Valves Limited (Formerly Audco India Limited) is a wholly owned subsidiary of Larsen & Toubro. Backed

More information

Pilot-Operated Regulators

Pilot-Operated Regulators Fisher Controls Instruction Manual Type 1098-EGR & 1098H-EGR Pilot-Operated Regulators R May 1987 Form 5084 Contents Introduction................................... 2 Scope of Manual..............................

More information

GBV-G Balancing Valves

GBV-G Balancing Valves Ductile Iron ASTM A6, Grade 6-4-2 The Series GBV is a multi-turn, Y-style globe valve designed for accurate determination and control of fluid flow to circuits requiring precise balancing. Max. Working

More information

Maintenance Information

Maintenance Information 45528270 Edition 1 June 2007 Barring Motor T480 Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this Barring Motor.

More information

RAM Company USA Products Line

RAM Company USA Products Line RAM Company USA Products Line Trunnion Mounted Ball Valves Metal Seated Ball Valve 3-Way Ball Valve Jacket Ball Valve Ball Valves with Actuator Trunnion Mounted Ball Valves Main Features DOUBLE PISTON

More information

Swing-Flex Check Valve

Swing-Flex Check Valve Manual No. SFCV-OM1-14 Swing-Flex Check Valve Operation, Maintenance and Installation Manual INTRODUCTION.. 1 RECEIVING AND STORAGE. 1 DESCRIPTION OF OPERATION.. 1 INSTALLATION 2 VALVE CONSTRUCTION.. 2

More information

GROVE B4, B5 and B7 Side-entry Ball Valves

GROVE B4, B5 and B7 Side-entry Ball Valves GROVE B4, B5 and B7 Side-entry Ball Valves Table of Contents GROVE B4, B5 and B7 SIDE-ENTRY BALL VALVES Features and Benefits Applications...1 GROVE B4 Design Features...2 Materials Specifications...4

More information

ENGINEERING STANDARD

ENGINEERING STANDARD PAGE: 1 OF 31 SUBMITTED BY: J. JOSEPH APPROVED BY: ED PEARSON Overview Vendor: Cameron Valves and Measurement 3250 Briarpark Drive Houston, Texas 77041 U.S.A. Telephone: 281-499-8511 Fax: (281) 261-3635

More information

Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves

Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves SMITH VALVES Installation, Operation, and Maintenance Manual Full Port Y-Pattern, Bolted Bonnet, Globe and Check Valves Globe Valve Series: YG80/YG15 Welded Bonnet Globe Valve Series: YG87/YG17 Piston

More information

INSTALLATION - MAINTENANCE MANUAL Severe Service Series M4 Ball Valve

INSTALLATION - MAINTENANCE MANUAL Severe Service Series M4 Ball Valve INSTALLATION - MAINTENANCE MANUAL Severe Service Series M4 Ball Valve Date: May 2016/ Page 2 of 12 Table of Contents 1. Safety Information - Definition of Terms..........................2 2. Bill of Materials....................................

More information

MODEL APH HYDRAULIC ACTUATOR

MODEL APH HYDRAULIC ACTUATOR OPERATION & MAINTENANCE MANUAL MODEL APH HYDRAULIC ACTUATOR TABLE OF CONTENTS I. Introduction............................................. 3 II. Actuator Operation.........................................

More information

I-795/906. Series 795 and 906 Installation-Ready Knife Gate Valves WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS

I-795/906. Series 795 and 906 Installation-Ready Knife Gate Valves WARNING INSTALLATION AND MAINTENANCE INSTRUCTIONS INSTALLATION AND MAINTENANCE INSTRUCTIONS I-795/906 Series 795 and 906 Installation-Ready Knife Gate Valves HANDWHEEL OPERATOR PNEUMATIC OPERATOR HYDRAULIC OPERATOR WARNING Read and understand all instructions

More information

MUELLER ECCENTRIC PLUG VALVE

MUELLER ECCENTRIC PLUG VALVE MUELLER INSTALLATION, OPERATING and MAINTENANCE INSTRUCTIONS 1 MUELLER System Design The life of the valve is dependent on its application, frequency of use and freedom from misuse. The properties of the

More information

MODEL M AND MSG GATE VALVE SERVICE AND OPERATION MANUAL

MODEL M AND MSG GATE VALVE SERVICE AND OPERATION MANUAL MODEL M AND MSG GATE VALVE SERVICE AND OPERATION MANUAL Page 1 INTRODUCTION In appreciation to our customer for purchasing our product, we have prepared this Operation Manual to assist you in the Operation,

More information

THROUGH CONDUIT VALVES TECHNICAL CATALOGUE

THROUGH CONDUIT VALVES TECHNICAL CATALOGUE SITINDUSTRIE VALVO VALVES THROUGH CONDUIT VALVES Ed. 01/DIC-2004 SITINDUSTRIE reserves the right to change, without notice, 1/14 SITINDUSTRIE TRIE VALVE DIVISION We are pleased to introduce you to the

More information

Contents. Dimensions and weights

Contents. Dimensions and weights G4N Gate Valves Through-conduit, double block-and-bleed slab gate valves with fully protected seat faces for long-lasting, drop-tight shutoff in liquid pipelines Contents General information 3 Standard

More information

Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822

Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Installation, Operation and Maintenance Guide II NIBCO High Performance Butterfly Valves Series 6822 and 7822 Statements: NIBCO High Performance Butterfly Valves, Series 6822 and 7822, have been designed

More information

Double Block and Bleed Plug Valves

Double Block and Bleed Plug Valves Double Block and Bleed Plug Valves ASME Class 150 to 600 50 mm to 1050 mm (2 to 42 ) API 6D L&T Valves L&T Valves is a wholly owned subsidiary of Larsen & Toubro. Backed by a heritage of excellence that

More information

VELAN TRUNNION-MOUNTED

VELAN TRUNNION-MOUNTED VELAN TRUNNION-MOUNTED Velan s standard trunnion-mounted ball valves offer increased value by incorporating advanced design features. TRUNNION-MOUNTED BALL The ball is fixed and the seat rings are floating,

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual Installation, Operation and Maintenance Manual for the MOGAS ISOLATOR 2.0 Floating Ball Valve 1, 1.5, 2, 3 and 4 inch PREPARE THE VALVE FOR INSTALLATION INSTALL THE VALVE PROPERLY MAINTAIN THE VALVE FOR

More information

Cylinder and Valve: AirHawk II Air Mask

Cylinder and Valve: AirHawk II Air Mask Cylinder and Valve: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 011 (L) Rev. 0 MSA 2010 Prnt. Spec. 10000005389(I) Mat. 10104218 Doc. 10104218 Parts List Cylinder Replacement Kits Item P/N Description

More information

Technical Data. Sizes 2 in. to 24 in. (DN50 to DN600) Approvals UL and ULC Listed FM Approved

Technical Data. Sizes 2 in. to 24 in. (DN50 to DN600) Approvals UL and ULC Listed FM Approved Worldwide Contacts www.tyco-fire.com Model TJP Resilient-Seated Gate Valves with Vertical or Cross Wall Post Indicator General Description TYCO Model TJP Resilient-Seated Gate Valves with Vertical and

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual brands you trust. Installation, Operation and Maintenance Manual Trunnion Ball Design 1. Maintenance Page 3 2. Exploded view Page 4 3. Dissassembly, Inspection Page 5 4. Reassembly Page 5-8 CAUTION READ

More information

COMMERCIAL. BV & BVM Series Installation Instructions 06/29/15

COMMERCIAL. BV & BVM Series Installation Instructions 06/29/15 COMMERCIAL Bray Controls Commercial Division 13788 West Road, Suite 00A Houston, Texas 77041 BCDSales@Bray.com Phone: 1-888-41-79 Fax: 1-888-41-70 www.braycommercialdivision.com BV & BVM Series Installation

More information

FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL

FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL FRP BALL VALVES TABLE OF CONTENTS MAINTENANCE AND INSTALLATION INSTRUCTIONS 1. 2. 2.1 2.2 2.3 2.4 GENERAL...Page 1 HANDLING...1 Receiving and Storing...1

More information

MAGNUM GATE VALVES. Invention, Unique Design & Extraordinary Craftsmanship. WORLDWIDE OILFIELD MACHINE Est. 1980

MAGNUM GATE VALVES. Invention, Unique Design & Extraordinary Craftsmanship.   WORLDWIDE OILFIELD MACHINE Est. 1980 TM MAGNUM GATE VALVES www.womusa.com Invention, Unique Design & Extraordinary Craftsmanship WORLDWIDE OILFIELD MACHINE Est. 980 Table of Contents Patented Dual-Seal Technology Magnum Gate Valve 2 Magnum

More information

INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS:

INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: INSTRUCTION MANUAL INTERNAL GEAR PUMP TITAN G-4124A SERIES=> FLANGED TITAN G-124A SERIES => FLANGED MODELS: G-H, G-HL, G-K, G-KK, G-L, G-LQ, G-LL, GLS, G-Q, G-QS 1 Contents Maintenance Thrust bearing adjustment

More information

METERING VALVE 2" STEM GUIDED

METERING VALVE 2 STEM GUIDED 2" STEM GUIDED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed

More information

DEMCO DEMCO RESILIENT SEATED BUTTERFLY VALVE. Installation, Operation and Maintenance Manual D I S T R I B U T E D V A L V E S DEM-RSBV-IOM

DEMCO DEMCO RESILIENT SEATED BUTTERFLY VALVE. Installation, Operation and Maintenance Manual D I S T R I B U T E D V A L V E S DEM-RSBV-IOM DEMCO RESILIENT SEATED BUTTERFLY VALVE DEMCO TABLE OF CONTENTS DEMCO RESILIENT SEATED BUTTERFLY VALVE Bill of Materials... 1 Scope... 3 Nameplate Information... 3 Storage... 3 Installation... 4 End-of-Line

More information

Engineered Valves For Pipeline Service Application

Engineered Valves For Pipeline Service Application Page 1 TRUNNION MOUNTED BALL VALVES TM SERIES Engineered Valves For Pipeline Service Application Valves for oil & gas pipelines and other industrial applications Flanged or Butt Weld ANSI Class 150 thru

More information

Repair Manual MECHANICAL OIL VALVE

Repair Manual MECHANICAL OIL VALVE MECHANICAL OIL VALVE Repair Manual This Manual for Mechanical Oil Valves purchased before December 2017 INDEX Introduction... 1 Elastomer Materials... 2 Repair Kit Contents... 3 Disassembly... 4 Appendix

More information

Kimray reserves the right to modify or improve the designs or specifications of such products at any time without prior notice Kimray Inc.

Kimray reserves the right to modify or improve the designs or specifications of such products at any time without prior notice Kimray Inc. TREATER VALVE All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed

More information

Slab & Double Expanding Gate Valves

Slab & Double Expanding Gate Valves Slab & Double Expanding Gate Valves Double Expanding Characteristics The main feature of a double expanding gate valve is the 2 pieces obturator that guarantees a simultaneous mechanical seal both in the

More information

Easy Riser swing check valve Models E-1 & F-1

Easy Riser swing check valve Models E-1 & F-1 Page 1 of 7 1. DESCRIPTION The Viking Easy Riser Swing Check Valve is a general purpose rubber-faced approved for use in fire service systems. The valve is for use in wet system risers, preaction system

More information

LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED

LOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED DIAPHRAGM BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to

More information

Swing-Flex Check Valve

Swing-Flex Check Valve Manual No. SFCV-OM1-11 Swing-Flex Check Valve Operation, Maintenance and Installation Manual INTRODUCTION 1 RECEIVING AND STORAGE 1 DESCRIPTION OF OPERATION 1 INSTALLATION 2 VALVE CONSTRUCTION 2 MAINTENANCE

More information

Installation, Operation, and Maintenance Manual GENERAL VALVE GENERAL VALVE TRUSEAL / IOM-GEN-TRUSEAL. Installation, Operation, and Maintenance Manual

Installation, Operation, and Maintenance Manual GENERAL VALVE GENERAL VALVE TRUSEAL / IOM-GEN-TRUSEAL. Installation, Operation, and Maintenance Manual Installation, Operation, and Maintenance Manual GENERAL T GENERAL VALVE Installation, Operation, and Maintenance Manual Cameron s Valves & Measurement Group Revised 10/07 IOM-GEN-TRUSEAL Installation,

More information

Triad Series. 3 Piece Ball Valves Full Port: 1 /4-4 Standard Port: 3 /4-2 1 /2. Model FP - Full Port Model SP - Standard

Triad Series. 3 Piece Ball Valves Full Port: 1 /4-4 Standard Port: 3 /4-2 1 /2. Model FP - Full Port Model SP - Standard A Bray High Performance Company A Subsidiary of BRAY INTERNATIONAL, Inc. 3 Piece Ball Valves Full Port: 1 / - Standard Port: 3 / - 1 / Triad Series Model FP - Full Port Model SP - Standard Port Flow-Tek

More information

Fisher 657 Diaphragm Actuator Sizes and 87

Fisher 657 Diaphragm Actuator Sizes and 87 Instruction Manual 657 Actuator (30-70 and 87) Fisher 657 Diaphragm Actuator Sizes 30 70 and 87 Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications... 2 Installation... 3 Mounting

More information

IOM Manual. IOM Manual. Series 76/77.

IOM Manual. IOM Manual. Series 76/77. IOM Manual IOM Manual Series 76/77 www.flowlinevalves.com Flow Line Valve and Controls, L.L.C. 110 Main Project Road Schriever, LA 70395 P.O. Box 677 Schriever, LA 70395 Phone 985-414-6004 * Toll Free

More information

MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL

MODEL 5540 CONTENTS. Installation, Operation and Maintenance Instructions 1.0 GENERAL Installation, Operation and Maintenance Instructions MODEL 5540 Sep 20 CONTENTS.0 GENERAL. Model Number---------------------------------------------------------------------------------------------------------------

More information

Newco / OIC / Cooper Forged Valves. Operation & Maintenance. Manual

Newco / OIC / Cooper Forged Valves. Operation & Maintenance. Manual NEWCO / OIC / COOPER VALVES Newmans Inc., Newmans Valve Ltd. Operation & Maintenance Manual Revision 2, 9 May 2007 1. Introduction and Safety Information... 1 1.1. Introduction... 1 1.2. Safety Information...

More information

Fabricated Bevel Gear Operator Bi-Directional Metal Seat 150 PSI Bi-Directional Resilient Seat 150 PSI

Fabricated Bevel Gear Operator Bi-Directional Metal Seat 150 PSI Bi-Directional Resilient Seat 150 PSI Knife Gate Valves Uni-Directional (Metal Seated) Manual Handwheel Style KGV...2 Carbon Steel Technical Data 150 PSI 2 24...3 304 Stainless Steel Technical Data 150 PSI 2 24...3 316 Stainless Steel Technical

More information

GT-200 GATE VALVES PN16, Screwed end

GT-200 GATE VALVES PN16, Screwed end Document No. : MD-QO-04-281 Date : 2009/07 /17 Version : 1.0 GT-200 GATE VALVES PN16, Screwed end USER MANUAL Modentic Industrial Corporation 14F-1,No.57Taya Rd.,Taichung,Taiwan,R.O.C. Email:modentic@ms9.hinet.net

More information

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS

GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS -S INDICATES CYLINDERS ARE IN TANDEM PART NUMBER: 100121 REVISION "A" ECN

More information

IMO-200EN 09/2010. Trunnion mounted forged ball valves Model FF and GG. Installation, Maintenance and Operating Instructions IMO-200EN 09/2010

IMO-200EN 09/2010. Trunnion mounted forged ball valves Model FF and GG. Installation, Maintenance and Operating Instructions IMO-200EN 09/2010 IMO-200EN 09/2010 Trunnion mounted forged ball valves Model FF and GG Installation, Maintenance and Operating Instructions IMO-200EN 09/2010 2 IMO-200EN Table of Contents I GENERAL INFORMATION...................

More information

Installation, Operation and Maintenance Manual for AlL Pressure seal Bonnet/Cover Class 600, 900, 1500 & 2500 Cast steel Gate, Globe & Check Valves

Installation, Operation and Maintenance Manual for AlL Pressure seal Bonnet/Cover Class 600, 900, 1500 & 2500 Cast steel Gate, Globe & Check Valves Installation, Operation and Maintenance Manual for AlL Pressure seal Bonnet/Cover Class 600, 900, 1500 & 2500 Cast steel Gate, Globe & Check Valves AUDCO INDIA LIMITED Chennai India AIL REF. No: IOM/PS/001

More information

PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY

PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been

More information

Type MR108 Direct-Operated Backpressure Regulator

Type MR108 Direct-Operated Backpressure Regulator Instruction Manual Form 5875 Type MR108 August 2013 Type MR108 Direct-Operated Backpressure Regulator Contents Introduction... 2 Specifi cations... 2 Principle of Operation... 6 Installation... 6 Overpressure

More information

DEMCO Resilient-Seated Butterfly Valve

DEMCO Resilient-Seated Butterfly Valve Document Number: TC003001-01 Revision: Rev 2 DEMCO Resilient-Seated Butterfly Valve Installation, Operation, and Maintenance Manual TABLE OF CONTENTS BILL OF MATERIALS... 3 SCOPE... 5 NAMEPLATE INFORMATION...

More information

Ideal Installation. I & M Mark 67 (1/2 6 ) Control Line. Installation & Maintenance Instructions for Mark 67 Pressure Regulators

Ideal Installation. I & M Mark 67 (1/2 6 ) Control Line. Installation & Maintenance Instructions for Mark 67 Pressure Regulators I & M Mark (/ ) 0 Wasson Road Cincinnati, OH 0 USA Phone --00 Fax -8-00 info@richardsind.com www.jordanvalve.com Installation & Maintenance Instructions for Mark Pressure Regulators Warning: Jordan Valve

More information

PRESSURE REDUCING VALVE

PRESSURE REDUCING VALVE Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve

More information

Type 63EG Relief Valve or Backpressure Regulator

Type 63EG Relief Valve or Backpressure Regulator Instruction Manual Form 5110 Types 63EG and 1098-63EGR July 2011 Type 63EG Relief Valve or Backpressure Regulator! WARNING Failure to follow these instructions or to properly install and maintain this

More information

PRODUCT OVERVIEW. Our BDB (Bolted Body) and BW3 (Fully Welded Body) trunnion-mounted ball valves are designed and manufactured

PRODUCT OVERVIEW. Our BDB (Bolted Body) and BW3 (Fully Welded Body) trunnion-mounted ball valves are designed and manufactured PRODUCT OVERVIEW For over 30 years, FluoroSeal has been manufacturing and customizing a wide range of valves, and accessories for many industries including Oil & Gas, Petrochemical, Chemical, Mining, Pharmaceutical,

More information

Model-1 Natural Gas Valves

Model-1 Natural Gas Valves Flanged End 285 Screwed Weld End Locking Devices KEROTEST Model-1 s Short Weld End Long Weld End Weld x Flange 500 / 740 Flanged End 500 / 740 Weld x Flange 285 Model-1 Short Weld End Standard Welding

More information

PRESSURE REDUCING VALVE

PRESSURE REDUCING VALVE Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Low Flow By-Pass controls at low flows 4 PRESSURE REDUCING VALVE with LOW-FLOW BY-PASS FEATURE Main Line valve

More information

INSTRUCTION MANUAL AND PARTS LIST FOR SERIES 8L-630J AND 630M WARNING

INSTRUCTION MANUAL AND PARTS LIST FOR SERIES 8L-630J AND 630M WARNING INSTRUCTION MANUAL AND PARTS LIST FOR SERIES 8L-630J AND 630M WARNING READ CA-l AND TIDS INSTRUCTION MANUAL PRIOR TO INSTALLATION, OPERATION OR MAINTENANCE WARNING This Instruction Manual and General Instructions

More information

HIGH PRESSURE CONTROL VALVE PISTON BALANCED

HIGH PRESSURE CONTROL VALVE PISTON BALANCED PISTON BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be

More information

W-K-M Model MA-1 DynaCentric Butterfly Valve

W-K-M Model MA-1 DynaCentric Butterfly Valve Page 1 of 12 W-K-M Model MA-1 DynaCentric Butterfly Valve Page 2 of 12 Published January 2003 W-K-M and DynaCentric are trademarks of Cooper Cameron Corporation Cooper Cameron Corporation, Cooper Cameron

More information

PRESSURE REDUCING CONTROL VALVE

PRESSURE REDUCING CONTROL VALVE PRESSURE REDUCING CONTROL VALVE 06/08 Schematics Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) X P/L Standard Components 1 Main

More information

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS D SERIES TABLE OF CONTENTS

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS D SERIES TABLE OF CONTENTS INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS D SERIES GENERAL INFORMATION TERMS CONCERNING SAFETY UNPACKING INSTALLATIONS VALVE MAINTENANCE TABLE OF CONTENTS VALVE DISASSEMBLY AND REASSEMBLY PLUG

More information

THREE PIECE TRUNNION MOUNTED BALL VALVE

THREE PIECE TRUNNION MOUNTED BALL VALVE Page: 1 of 13 INSTALLATION, OPERATION & MAINTENANCE MANUAL KF SERIES P3/M3 THREE PIECE TRUNNION Page: 2 of 13 CONTENTS BILL OF MATERIALS --------------------------------------------------------------------------------------------------------------------------------------------------

More information

6701 KNIFE GATE VALVES

6701 KNIFE GATE VALVES INTRODUCTION This instruction manual includes installation, operation and maintenance information for 2" through 30" stainless steel and stainless steel lined knife gate valves. This manual addresses hand-wheel

More information

½" to 4" (DN15 to DN100) LEA31 and LEA33 ANSI Control Valves Installation and Maintenance Instructions

½ to 4 (DN15 to DN100) LEA31 and LEA33 ANSI Control Valves Installation and Maintenance Instructions 00050/1 IM-P0-02 CH Issue 1 ½" to " (DN15 to DN100) LEA1 and LEA ANSI Control Valves Installation and Maintenance Instructions 1. Safety 2. Technical details. Installation and commissioning. Maintenance

More information

PRODUCT NEWS CAT.NO.-70 KPC CORPORATION FLOW CONTROL DIVISION

PRODUCT NEWS CAT.NO.-70 KPC CORPORATION FLOW CONTROL DIVISION PRODUCT NEWS CAT.NO.-70 CERTIFIED TO ISO 9001 KPC CORPORATION FLOW CONTROL DIVISION Internal or External Trunnion Design KPC Construction Features BODY GASKET The tongue - and - groove body gasket maximizes

More information

TRUNNION BALL VALVES. TBV 7.10

TRUNNION BALL VALVES.     TBV 7.10 TRUNNION BALL VALVES WWW.VALVE.COM TBV 7.10 ABOUT US Our mission at Universal Flow (), is to provide a quality product at a competitive price and to meet the needs and requirements of our customers in

More information

TECHNICAL DATA OBSOLETE

TECHNICAL DATA OBSOLETE August 31, 2006 Check Valve 815a 1. PRODUCT NAME Viking Easy Riser Swing Check Valve Model E-1: Available since 1992 Model F-1: Available since 1994 2. MANUFACTURER The Viking Corporation 210 N. Industrial

More information

Fisher 1061 Pneumatic Piston Rotary Actuator with Style H & J Mounting Adaptations

Fisher 1061 Pneumatic Piston Rotary Actuator with Style H & J Mounting Adaptations Instruction Manual 1061 H & J Actuator Fisher 1061 Pneumatic Piston Rotary Actuator with Style H & J Mounting Adaptations Contents Introduction... 1 Scope of Manual... 1 Description... 2 Specifications...

More information

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL

Fluid-O-Tech ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL Fluid-O-Tech PUMP TECHNOLOGY AT ITS BEST WWW.FLUID-O-TECH.COM Office: 161 Atwater St., Plantsville, CT 06479 Phone: (860) 276-9270 Fax: (860) 620-0193 ROTOFLOW ROTARY VANE PUMP REBUILD MANUAL 08/09 Ed.,

More information

A Zy-Tech Global Industries Product

A Zy-Tech Global Industries Product A Zy-Tech Global Industries Product Worm & evel Gear Operators Another quality product from Zy-Tech Global Industries, Inc. Zy-Gear gear operators are designed for long lasting dependable service in oil

More information

WKM Model MB DynaCentric High Performance Butterfly Valve

WKM Model MB DynaCentric High Performance Butterfly Valve Document Number: TC003001-10 Revision: Rev 1 WKM Model MB DynaCentric High Performance Butterfly Valve Installation, Operation, and Maintenance Manual TABLE OF CONTENTS BILL OF MATERIALS... 3 CATALOG NUMBER

More information

Mustang Series PRESSURE REDUCING CONTROL VALVE. M115 (Globe) M1115 (Angle) Schematic. Standard Components. Options & Accessories.

Mustang Series PRESSURE REDUCING CONTROL VALVE. M115 (Globe) M1115 (Angle) Schematic. Standard Components. Options & Accessories. PRESSURE REDUCING CONTROL VALVE 02/09 Schematic Throttles to reduce high upstream pressure to constant lower downstream pressure Reducing setpoint is adjustable 2 (AOS) P/L Standard Components 1 Main Valve

More information

OPERATING AND MAINTENANCE MANUAL

OPERATING AND MAINTENANCE MANUAL Series 2700A Engineered Performance TABLE OF CONTENTS INTRODUCTION 1 Scope 1 Description 1 Valve Identification 1 0 VALVE INSTALLATION 1 0 VALVE MAINTENANCE 2 1 Actuator Disassembly 3 2 Actuator Reassembly

More information

E N G I N E E R E D V A L V E S. B4, B5 & B7 Side Entry Ball Valves GROVE

E N G I N E E R E D V A L V E S. B4, B5 & B7 Side Entry Ball Valves GROVE B4, B5 & B7 Side Entry Ball Valves TABLE OF CONTENTS B4 B5 B7 SIDE ENTRY BALL VALVE FEATURES AND BENEFITS General Information 1 B4 Design Features 2 & 3 Valve Assembly and Cross Section 4 Dimensions and

More information

GWC Italia. Proven technology for individual valve solutions worldwide API 6D THROUGH CONDUIT SLAB & PARALLEL EXPANDING GATE VALVES PGV-1002

GWC Italia. Proven technology for individual valve solutions worldwide API 6D THROUGH CONDUIT SLAB & PARALLEL EXPANDING GATE VALVES PGV-1002 GWC Italia Proven technology for individual valve solutions worldwide API 6D THROUGH CONDUIT SLAB & PARALLEL EXPANDING GATE VALVES PGV-1002 2 GWC ITALIA Proven technology for individual valve solutions

More information

DN15 DN250 PN 16. Corrosion Protection

DN15 DN250 PN 16. Corrosion Protection PRODUCTION STANDARTS DN15 DN250 PN 16 Design DIN 3357 Connection EN 1092-2 / ISO 7005-2 Face to Face DN15-DN150: EN558 Series 14 / DIN 3202 F4 DN200-DN250: EN558 Series 27 / DIN 3202 F5 Marking EN 19 Tests

More information

type 63Eg Relief Valve or Backpressure Regulator

type 63Eg Relief Valve or Backpressure Regulator Instruction Manual Form 5110 Types 63EG and 1098-63EGR March 2016 type 63Eg Relief Valve or Backpressure Regulator! WARning Failure to follow these instructions or to properly install and maintain this

More information

Through Conduit Gate Valves Slab & Expanding

Through Conduit Gate Valves Slab & Expanding Through Conduit Gate Valves Slab & Expanding Through Conduit Slab Gate valve Slab Gate Valves are manufactured with a full bore port, rising stem OS&Y and with floating seats and gate, pressure energized,

More information

OPERATION MANUAL INTERNAL GEAR PUMP. Models: NG-H, NG-HL, NG-K, NG-KK, NG-L, NG-LQ, NG-LL, NG-LS, NG-Q, NG-QS. Tel: Fax:

OPERATION MANUAL INTERNAL GEAR PUMP. Models: NG-H, NG-HL, NG-K, NG-KK, NG-L, NG-LQ, NG-LL, NG-LS, NG-Q, NG-QS. Tel: Fax: OPERATION MANUAL INTERNAL GEAR PUMP Models: NG-H, NG-HL, NG-K, NG-KK, NG-L, NG-LQ, NG-LL, NG-LS, NG-Q, NG-QS. 1 Contents Pump Designation System Maintenance Thrust bearing adjustment Pressure Relief Valve

More information