Sporlan Thermostatic Expansion Valves

Transcription

1 aerospace climate control electromechanical filtration fluid & gas handling hydraulics pneumatics process control sealing & shielding Splan Thermostatic Expansion Valves ulletin 10-10, October 2009

2 t THERMOSTTI EXPNSION VLVES ULLETIN Page 1 10 Outstanding Features & enefits of Splan Thermostatic Expansion Valves SELETIVE THERMOSTTI HRGES Designed to provide optimum perfmance f all applications air conditioning and heat pump, medium and low temperature refrigeration. THERMOSTTI ELEMENT DESIGN Long lasting and field proven stainless steel diaphragm and welded element construction. DIPHRGM DESIGN Large flat diaphragm permits precise valve control. REPLELE THERMOSTTI ELEMENTS Field replaceable elements on all standard valves. ESSILE INTERNL PRTS Durable, leakproof body joint construction allows the valve to be disassembled, and the internal parts cleaned and inspected. PIN RRIER DESIGN (ONVENTIONL VLVES) Provides precise pin and pt alignment, and tighter seating. LNED PORT DESIGN Provides perfect pin and pt alignment, and prevents changes in pressure drop across the valve from influencing valve operation. Provides excellent control on applications with widely varying operating conditions. MTERILS OF ONSTRUTION Pin and pt materials offer maximum protection against crosion and erosion. SILVER SOLDERED ONNETIONS F leakproof, high strength connection-to-body joints. DJUSTLE SUPERHET DESIGN ll standard valves are externally adjustable. The thermostatic expansion valve (TEV) controls the flow of liquid refrigerant entering the direct expansion (DX) evapat by maintaining a constant superheat of the refrigerant vap at the outlet of the evapat. The TEV controls the difference between the actual temperature and the saturation temperature of the refrigerant cresponding to the suction pressure at the sensing bulb location; this is superheat. y controlling superheat, the TEV keeps most of the evapat surface active, while preventing liquid refrigerant from returning to the compress. The ability of the TEV to match refrigerant flow to the rate at which refrigerant can be vapized in the evapat makes the TEV the ideal expansion device f most air conditioning and refrigeration applications. TLE OF ONTENTS Selection Procedure...2 Valve Nomenclature / Ordering Instructions... Recoended Thermostatic harges... TEV apacity Ratings f Refrigerants: 22, 14a, 401, 402, 404, 407, 408, 409, 410, 422D, and apacity Tables f Refrigerants: 22, 14a, 401, 402, 404, 407, 408, 409, 410, 422D, and TEV Quick Reference Guide Valve Specifications R...12 ER...1 F & EF Q, EQ, & SQ Q, EQ, & SQ G...22 EG...2 F...24 SF & EF S...27 ES...28 O H...1 M... 2 V... W... 4 Materials and Details of onstruction... 5 OEM Type Thermostatic Expansion Valves... 6 Refer to ulletin 10-9 f a complete discussion on The They of Operation and pplication of Thermostatic Expansion Valves. Refer to ulletin f a complete discussion on Installing and Servicing Thermostatic Expansion Valves. FOR USE ON REFRIGERTION and/ IR ONDITIONING SYSTEMS ONLY ulletin 10-10, October 2009 supersedes ulletin 10-10, July 2008 and all pri publications. opyright 2009 by Parker Hannifin pation, Splan Division, Washington, Missouri

3 Page 2 ULLETIN t SELETION PROEDURE The following procedure should be used when selecting a Splan TEV: 1. Determine the liquid temperature of the refrigerant entering the valve. The TEV capacity tables on pages 4 to 8 are based on a liquid temperature of 100 F f R-22, R-14a, R401, R-402, R-404, R-407, R-408, R-409, R-410, and R-507. F other liquid temperatures, apply the crection fact given in the tables f each refrigerant. F example see Table. 2. Determine pressure drop across valve. The pressure drop crection facts are based on standard liquid temperature and pressure drop. The standard pressure drop is dependent on the evapat temperature. To determine the pressure drop, subtract the saturated pressure equivalent to evapat temperature from the condensing pressure. The condensing pressure used in this calculation should be the minimum operating condensing pressure of the system. From this value, subtract all other pressure losses to obtain the net pressure drop across the valve. Use this value to determine the pressure drop crection fact. F example see Table. e sure to consider all of the following possible sources of pressure drop: 1. Friction losses through refrigeration lines including the evapat and condenser. 2. Pressure drop across liquid line accessies such as a solenoid valve and filter-drier.. Static pressure loss (gain) due to the vertical lift (drop) of the liquid line. 4. Pressure drop across a refrigerant distribut if used. Refer to ulletin f infmation on refrigerant distributs.. Select valve from the capacity tables. Select a valve based on the design evapating temperature. If possible the valve capacity should be equal slightly exceed the design rating of the system. e sure to apply the appropriate crection facts f liquid temperature and pressure drop. Once the desired valve capacity has been located, determine the nominal capacity of the valve from the tables second column. On multiple evapat systems, select each valve on the basis of individual evapat capacity. F example see Table. 4. Determine if an external equalizer is required. The amount of pressure drop between the valve outlet and bulb location will determine if an external equalizer is required. Refer to ulletin 10-9 f further infmation on this subject. 5. Select body type. Select the body type accding to the style connections desired. F complete specifications on each TEV type including nominal ratings, refer to pages 9 to Select the Splan Selective Thermostatic harge. Select the charge accding to the design evapating temperature from the Table on page. Refer to ulletin 10-9 f a complete discussion of the available Splan Selective Thermostatic harges. Selection Example Refrigerant 22 pplication: medium temperature refrigeration Design evapat temperature F Design condenser temperature F Refrigerant liquid temperature F Design system capacity... 1 ton vailable pressure drop across TEV: ondensing pressure (psig) Evapating pressure (psig) Liquid line and accessies loss (psi)... 4 Distribut and tubes loss (psi) Q Refrigerant liquid crection fact Pressure drop crection fact Use the following fmula to calculate TEV capacity: TEV apacity = TEV rating x F liquid temperature x F pressure drop EGVE-1 has valve capacity of: 1.09 x 1.17 x 0.89 = 1.14 Tons at 20 F evapating temperature, 100 psi pressure drop and 70 liquid temperature. Thermostatic charge (from table on page ): V W Selection: EGVE-1- /8 x 1/2 x 1/4 ODF x 5 Q n externally equalized valve must be used on evapats employing a refrigerant distribut due to the pressure drop created by the distribut. In addition, an externally equalized valve should always be used with air conditioning thermostatic charges to reduce the possibility of thermostatic charge migration. W Please note that the refrigerant charge designation in the thermostatic charge ( V in this case) is dropped when it is incpated into the valve model designation. t THERMOSTTI EXPNSION VLVE PITIES f S - TONS IR ONDITIONING, HET PUMP and OMMER VLVE TYPES NOMINL PITY 22 REOMMENDED THERMOSTTI V, VP100, VG VZ, VZP40 EVPORTOR TEMPERTURE F F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG 1/ G-EG / F-EF-G-EG F-EF-G-EG 1-1/ Table The valve capacity should equal slightly exceed the tonnage rating of the system. (F complete R-22 capacity tables, see pages 4 and 5.) Design Evapating Temperature EVPORTOR TEMPERTURE F Liquid Temperature LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE TEV Pressure Drop PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP & & Table Table

4 t SELETION PROEDURE ULLETIN Page 7. Valve Nomenclature / Ordering Instructions ombine the letters and numbers in the following manner to obtain the complete valve designation. lso include all connection sizes and the capillary tube length. EXMPLE EG V E 1 ody Type Splan ode Refrigerant Element Label ol ode F = R-12 Yellow V = R-407 Green E = R-1 lue N = R-407 Lt. rown V = R-22 Green S = R-408 Purple G = R-2 lue F = R-409 Yellow M = R-124 lue Z = R-410 Rose J = R-14a lue V = R-422D Green X = R-401 Pink R = R-502 Purple L = R-402 Sand W = R-50 lue S = R-404 Orange P = R-507 Teal W = R-508 lue E specifies external equalizer. Omission of letter E indicates valve with internal equalizer. e.g. EGV-1- Nominal apacity in Tons Thermostatic harge /8 ODF SOLDER Inlet onnection Size and Style x 1/2 ODF SOLDER Outlet onnection Size and Style x 1/4 ODF SOLDER x 5 onnection Size and Style apillary Tubing Length Inches Feet REOMMENDED THERMOSTTI HRGES* SPORLN SELETIVE HRGES ENGINEERED f PEK PERFORMNE f EH SPEIFI PPLITION PPLITION ir onditioning oercial 50 F to -10 F Low Temperature 0 F to -40 F Extreme Low Temperature -40 F to -100 F TUL 12, 22, 422D, THERMOSTTI a , HRGES FP60 JP60 XP60 JP60 VP100 NP100 VP100 ZP180 ZP180 VG NG VG SP115 RP115 SP115 ZG ZG F J X J V N V S R S L P P FZ JZ FZP JZP VZ VZ VZP40 VZP40 LZ SZ RZ PZ SZ LZP SZP RZP PZP SZP VX VX LX SX RX PX SX *PPLITION FTORS: 1. The Type ZP charges have essentially the same characteristics as the Type Z charge with one exception: they produce a pressure limit Maximum Operating Pressure (MOP). ZP charges are not intended as replacements f Z charges. Each should be selected f its own unique purpose. 2. ll air conditioning and heat pump charges are intended f use with externally equalized valves.. Type L liquid charges are also available f most coonly used refrigerants in most element sizes. 4. The Type X charges are not to be used with ES and O valves. 5. If in doubt as to which charge to use, review the section on thermostatic charges in ulletin 10-9 contact Splan Division of Parker, Washington, Missouri with complete system data. 6. F dual temperature applications, use the charge. 7. The charge may be used on applications down to -0 F on R-22, R-404 and R-507. TEV PITY RTINGS FOR S: 22, 14a, 401, 402, 404, 407, 408, 409, 410, 422D, 507 TEV capacity ratings f R-22, R-14a, R-401, R-402, R-404, R-407, R-408, R-409, R-410, R-422D, and R-507 are based on vap free 100 F liquid refrigerant entering the expansion valve, a maximum opening superheat of 7 F, and a standard facty air test superheat setting. discussion of the relationship between valve capacities and superheat settings can be found in ulletin The ratings f evapat temperatures 40 F, 20 F, -10 F, -40 F in the capacity tables are in accdance with NSI/RI Standard Number 750. TEVs are tested in accdance with NSI/SHRE 17. TEV models featuring the mechanical pressure limit style thermostatic elements, i.e., the Types G(PL) and (PL) TEVs, are now obsolete. onsult ulletin f additional infmation on this subject and replacement valves. F TEV capacity ratings at operating conditions not shown in the following tables, contact Splan Division of Parker.

5 Page 4 ULLETIN t THERMOSTTI EXPNSION VLVE PITIES f S - TONS OF REFRIGERTION 22, 422D, 407 IR ONDITIONING, HET PUMP and OMMERIL REFRIGERTION PPLITIONS VLVE TYPES NOMINL PITY DQ 407 REOMMENDED THERMOSTTI HRGE V, VP100, VG VZ, VZP40 V, VP100, VG VZ, VZP40 N, NP100, NG EVPORTOR TEMPERTURE F F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG 1/ G-EG / F-EF-G-EG F-EF-G-EG 1-1/ F&EF(Ext)-G&EG(Ext)-S F&EF (Int)-G&EG(Int) 2-1/ F&EF (Ext)-G&EG (Ext)-S S S S(Ext) S(Ext) H 5-1/ H H H H M M M M LNED PORT THERMOSTTI EXPNSION VLVES F-EF-SF F-EF-SF F-EF-SF F-EF-SF F-EF-SF ES ES ES ES O O O O O O V V V W W VLVE TYPES RTRIDGE NO. REPLELE RTRIDGE THERMOSTTI EXPNSION VLVES Q-EQ-SQ 0 1/ Q-EQ-SQ 1 / Q-EQ-SQ Q-EQ-SQ 1-1/ Q-EQ-SQ 4 2-1/ Q-EQ-SQ 5-1/ Q-EQ-SQ Q-EQ-SQ alanced pt replaceable cartridges,,,, and, have the same capacities as the matching nominal capacity of the standard balanced pt valves above. LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE D EVPORTOR TEMPERTURE F PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP & & Q R-422D can be used in a system with R-22 valves, but the TEV capacity will be reduced. Please verify valve capacity will handle system load. These facts include crections f liquid refrigerant density and net refrigerating effect and are based on an evapat temperature of 0 F. However, they may be used f any evapat temperature from -40 F to 40 F since the variation in the actual facts across this range is insignificant. TEV apacity = TEV Rating x F Liquid Temperature x F Pressure Drop Example: ctual capacity of a nominal 2 ton R-22 Type S valve at 20 F evapat, 100 psi pressure drop across the TEV, and 90 F liquid temperature entering the TEV = 2.18 (from rating chart) x 1.06 (F liquid temperature) x 0.89 (F pressure drop) = 2.06 tons.

6 t THERMOSTTI EXPNSION VLVE PITIES f S - TONS OF REFRIGERTION ULLETIN Page 5 22, 422D, 407 IR ONDITIONING and HET PUMP PPLITIONS LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE D EVPORTOR TEMPERTURE F VLVE TYPES NOMINL PITY PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP & DQ 407 REOMMENDED THERMOSTTI HRGE VP100, VGW EVPORTOR TEMPERTURE F ER, R ER, R 1-1/ ER, R ER, R ER, R ER, R ER, R ER ER ER Q R-422D can be used in a system with R-22 valves, but the TEV capacity will be reduced. Please verify valve capacity will handle system load. W The R valve f R-22 applications is only available with a VG element. These facts include crections f liquid refrigerant density and net refrigerating effect and are based on an evapat temperature of 0 F. However, they may be used f any evapat temperature from -40 F to 40 F since the variation in the actual facts across this range is insignificant. TEV apacity = TEV Rating x F Liquid Temperature x F Pressure Drop Example: ctual capacity of a nominal 2 ton R-22 Type S valve at 20 F evapat, 100 psi pressure drop across the TEV, and 90 F liquid temperature entering the TEV = 2.18 (from rating chart) x 1.06 (F liquid temperature) x 0.89 (F pressure drop) = 2.06 tons. t THERMOSTTI EXPNSION VLVE PITIES f S - TONS OF REFRIGERTION 410 IR ONDITIONING and HET PUMP PPLITIONS VLVE TYPES NOMINL PITY 410 REOMMENDED THERMOSTTI HRGE ZP200, ZGQ EVPORTOR TEMPERTURE F ER, R ER, R 1-1/ ER, R ER, R ER, R ER, R ER, R ER ER 12-1/ ER LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE Q The R valve f R-410 applications is only available with a ZG element. VLVE TYPES VLVE TYPES EVPORTOR TEMPERTURE F NOMINL PITY 410 REOMMENDED THERMOSTTI HRGE ZP200, ZG EVPORTOR TEMPERTURE F OZE OZE OZE OZE OZE RTRIDGE TYPE Q, EQ, SQ 1/ Q, EQ, SQ / Q, EQ, SQ 1-/ Q, EQ, SQ -1/ Q, EQ, SQ PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP &

7 Page 6 ULLETIN t THERMOSTTI EXPNSION VLVE PITIES f S - TONS OF REFRIGERTION 404, 408 OMMERIL and LOW TEMPERTURE REFRIGERTION PPLITIONS VLVE TYPES NOMINL PITY REOMMENDED THERMOSTTI HRGE S, SP115 SZ, SZP S, SP115 SZ, SZP EVPORTOR TEMPERTURE F F-EF-G-EG F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG F-EF-G-EG 1-1/ F&EF(Ext)-G&EG(Ext)-S S S S (Ext) S (Ext) H H H 6-1/ H H M M M M LNED PORT THERMOSTTI EXPNSION VLVES F-EF-SF F-EF-SF F-EF-SF F-EF-SF F-EF-SF ES ES 7-1/ ES ES O O O O O O V V V VLVE TYPES RTRIDGE NO. REPLELE RTRIDGE THERMOSTTI EXPNSION VLVES Q-EQ-SQ 0 1/ Q-EQ-SQ 1 1/ Q-EQ-SQ 2 1/ Q-EQ-SQ Q-EQ-SQ 4 1-1/ Q-EQ-SQ Q-EQ-SQ Q-EQ-SQ alanced pt replaceable cartridges,,,, and, have the same capacities as the matching nominal capacity of the standard balanced pt valves above. LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE These facts include crections f liquid refrigerant density and net refrigerating effect and are based on an evapat temperature of 0 F. However, they may be used f any evapat temperature from -40 F to 40 F since the variation in the actual facts across this range is insignificant. EVPORTOR TEMPERTURE F PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP & & TEV apacity = TEV Rating x F Liquid Temperature x F Pressure Drop Example: ctual capacity of a nominal 1-1/2 ton R-404 Type EG valve at -20 F evapat, 125 psi pressure drop across the TEV, and 60 F liquid temperature entering the TEV = 1.26 (from rating chart) x 1.4 (F liquid temperature) x 0.91 (F pressure drop) = 1.64 tons.

8 ULLETIN Page 7 THERMOSTTI EXPNSION VLVE t PITIES f S - TONS OF REFRIGERTION 402, 507 OMMERIL and LOW TEMPERTURE REFRIGERTION PPLITIONS VLVE TYPES NOMINL PITY REOMMENDED THERMOSTTI HRGE L LZ, LZP P PZ, PZP EVPORTOR TEMPERTURE F F-EF-G-EG F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG F-EF-G-EG 1-1/ F&EF(Ext)-G&EG(Ext)-S S S S (Ext) S (Ext) H H H 6-1/ H H M M M M LNED PORT THERMOSTTI EXPNSION VLVES F-EF-SF F-EF-SF F-EF-SF F-EF-SF F-EF-SF ES ES 7-1/ ES ES O O O O O O V V V VLVE TYPES RTRIDGE NO. REPLELE RTRIDGE THERMOSTTI EXPNSION VLVES Q-EQ-SQ 0 1/ Q-EQ-SQ 1 1/ Q-EQ-SQ 2 1/ Q-EQ-SQ Q-EQ-SQ 4 1-1/ Q-EQ-SQ Q-EQ-SQ Q-EQ-SQ alanced pt replaceable cartridges,,,, and, have the same capacities as the matching nominal capacity of the standard balanced pt valves above. LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE These facts include crections f liquid refrigerant density and net refrigerating effect and are based on an evapat temperature of 0 F. However, they may be used f any evapat temperature from -40 F to 40 F since the variation in the actual facts across this range is insignificant. EVPORTOR TEMPERTURE F PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP & & TEV apacity = TEV Rating x F Liquid Temperature x F Pressure Drop Example: ctual capacity of a nominal 1-1/2 ton R-404 Type EG valve at -20 F evapat, 125 psi pressure drop across the TEV, and 60 F liquid temperature entering the TEV = 1.26 (from rating chart) x 1.4 (F liquid temperature) x 0.91 (F pressure drop) = 1.64 tons.

9 Page 8 ULLETIN t THERMOSTTI EXPNSION VLVE PITIES f S - TONS OF REFRIGERTION 14a, 401, 409 IR ONDITIONING, HET PUMP and OMMERIL REFRIGERTION PPLITIONS VLVE TYPES NOMINL PITY 14a REOMMENDED THERMOSTTI HRGE J, JP60 X, XP60 F, FP60 EVPORTOR TEMPERTURE F F-EF-G-EG F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG 1/ F-EF-G-EG F-EF-G-EG 1-1/ F&EF(Ext)-G&EG(Ext)-S S 2-1/ S S (Ext) S (Ext) H H H H H M M M LNED PORT THERMOSTTI EXPNSION VLVES F-EF-SF F-EF-SF F-EF-SF F-EF-SF F-EF-SF ES ES ES ES O O O O O O V V V W W VLVE TYPES RTRIDGE NO. REPLELE RTRIDGE THERMOSTTI EXPNSION VLVES Q-EQ-SQ 0 1/ Q-EQ-SQ 1 1/ Q-EQ-SQ 2 1/ Q-EQ-SQ Q-EQ-SQ 4 1-1/ Q-EQ-SQ Q-EQ-SQ 6 2-1/ Q-EQ-SQ alanced pt replaceable cartridges,,,, and, have the same capacities as the matching nominal capacity of the standard balanced pt valves above. LIQUID TEMPERTURE ENTERING TEV F ORRETION FTOR, F LIQUID TEMPERTURE 14a EVPORTOR TEMPERTURE F PRESSURE DROP ROSS TEV (psi) ORRETION FTOR, F PRESSURE DROP & These facts include crections f liquid refrigerant density and net refrigerating effect and are based on an evapat temperature of 0 F. However, they may be used f any evapat temperature from 0 F to 40 F since the variation in the actual facts across this range is insignificant. TEV apacity = TEV Rating x F Liquid Temperature x F Pressure Drop Example: ctual capacity of a nominal 1-1/2 ton R-14a Type EG valve at 20 F evapat, 100 psi pressure drop across the TEV, and 60 F liquid temperature entering the TEV = 1.91 (from rating chart) x 1.29 (F liquid temperature) x 1.12 (F pressure drop) = 2.76 tons.

10 t TEV QUIK REFERENE GUIDE ULLETIN Page 9 R VLVE TYPE SPES Page 12 NOMINL PITY RNGE (Tons) R-22 R-14a 1 6 R-404 & R-507 R ONNETION TYPES hatleff, SE Flare, ODF Solder VLVE DESRIPTION ND PPLITION Small brass body, externally adjustable valve available f R-22 and R-410 air conditioning and heat pump applications. This valve features a balanced pt construction and contains an internal check valve to eliminate the need f an external bypass check valve on heat pump applications. Suitable f replacing OEM type TEVs with without internal check valve on these applications. Inlet strainer is not included. ER Page ODF Solder Small brass body, externally adjustable valve available f R-22 and R-410 air conditioning and heat pump applications. This valve features a balanced pt construction and is approved f bi-directional operation. Suitable f replacing OEM type TEVs without internal check valve on these applications. 60 x 50 mesh inlet strainer is included with /8 inlet. F Page /5 2 2 SE Flare Small brass bar body, externally adjustable valve f small capacity refrigeration systems. SE flare inlet connection has a removable 100 mesh strainer. Typical applications: Refrigerated cases, coolers, freezers. EF Page /5 2 2 ODF Solder Same as the Type F valve except valve features ODF solder connections. The inlet connection has a 60 x 50 mesh insert type strainer. Typical applications: Refrigerated cases, coolers, freezers. Q/Q Page Q 1/ 5 Q 5-1/2 Q 1/6 2-1/2 Q Q 1/6 Q Q Q 1/4 6 SE Flare The brass body Type Q valve is externally adjustable with a removable cartridge ifice. The valve body, cartridge and thermostatic element is supplied as independent components. This allows body, cartridge and element to be assembled and matched to specific system requirements. Inlet connection has a 100 mesh removable strainer screen. Typical applications: applications and external equalized versions may be used on air conditioning. Type Q same as above, with balanced pt construction. EQ/EQ Page EQ 1/ 5 EQ 5-1/2 EQ 1/6 2-1/2 EQ EQ 1/6 EQ EQ EQ 1/4 6 Extended ODF Solder Type EQ same as the Type Q except it features extended ODF connections. 100 mesh insert strainer is provided with the valve. Type EQ same as Type EQ with balanced pt construction and is approved f bi-directional applications. SQ/SQ Page SQ 1/ 5 SQ 5-1/2 SQ 1/6 2-1/2 SQ SQ 1/6 SQ SQ SQ 1/4 6 Extended ODF Solder Type SQ same as the Type Q valve except it features ODF solder connections and a fged brass inlet fitting with a removable 100 mesh strainer screen which can be cleaned and/ replaced without removing the valve from the line. Type SQ is the same as Type SQ with balanced pt construction and is approved f bi-directional applications.

11 Page 10 ULLETIN t TEV QUIK REFERENE GUIDE G VLVE TYPE SPES NOMINL PITY RNGE (Tons) R-22 R-14a R-404 & R-507 R-410 ONNETION TYPES VLVE DESRIPTION ND PPLITION Page 22 1/5 2 2 SE Flare Fged brass body, externally adjustable valve f small capacity refrigeration systems. Inlet connection has a removable 100 mesh strainer. Typical applications: Refrigerated cases, coolers, freezers, small capacity air conditioners. EG Page 2 1/5 2 2 ODF Solder Same as the Type G valve except it features ODF solder connections and a fged brass inlet fitting with a removable 100 mesh strainer which can be cleaned and/ replaced without removing the valve from the line. F Page /2 SE Flare Same physical size as the Type F valve with SE flare connections except it features a balanced pt construction. Inlet connection has a removable 100 mesh strainer. Typical applications: Small capacity refrigeration that operates over widely varying operating conditions. SF Page /2 Extended ODF Solder Same as the Type F valve except it features ODF solder connections and a fged brass inlet fitting with a removable 100 mesh strainer which can be cleaned and/ replaced without removing the valve from the line. EF Page /2 Extended ODF Solder Same as the Type F valve except it features extended ODF connections. 100 mesh insert strainer is provided with the valve. S Page ODF Solder rass bar body, externally adjustable valve. Inlet has a permanent 12 mesh strainer. General purpose valve f air conditioning and refrigeration applications. ES Page Extended ODF Solder Same physical size as the Type S valve except it features extended ODF connections. This valve features a balanced pt construction which, depending on its capacity, makes it suitable f bi-directional operation. See page 28 f details.

12 t TEV QUIK REFERENE GUIDE ULLETIN Page 11 O VLVE TYPE SPES Page 29-0 NOMINL PITY RNGE (Tons) R-22 R-14a R-404 & R R ONNETION TYPES ODF Solder VLVE DESRIPTION ND PPLITION rass bar body, externally adjustable valve. Inlet has a permanent 12 mesh strainer. This valve features a balanced pt construction, and it is suitable f both air conditioning and refrigeration applications. Optional bi-directional feature available, please contact Splan Division of Parker f details. H Page 1 5-1/ ODF Solder FPT Flange rass bar body, externally adjustable valve with flange connections. Inlet flange bushing has a permanent 16 mesh strainer. The FPT flange connection requires the K-1178 adapter kit. This valve provides the smallest capacity TEVs with flange connections and it is suitable f both air conditioning and refrigeration applications. M Page ODF Solder FPT Flange ast bronze body, externally adjustable valve with flange connections. Inlet has a 12 mesh strainer. This valve type provides valve capacities greater than the Type H and it is suitable f air conditioning and refrigeration applications. Flanges f the Type M valve are interchangeable with the Type V valve. V Page ODF Solder FPT Flange ast bronze body, externally adjustable valve with flange connections. Inlet has a 12 mesh strainer. This valve type features a dual pt semi-balanced design. This valve type provides valve capacities greater than the Type M and is suitable f air conditioning and refrigeration applications. Flanges f the Type V are interchangeable with the Type M. W Page 4 15 & & 110 ODF Solder Flange ast bronze body, externally adjustable valve with flange connections. Inlet has a 12 mesh strainer. This valve type features a dual pt semi-balanced design and it is primarily f large capacity chillers. This valve type provides the largest valve capacities available f flange connection TEVs.

13 Page 12 ULLETIN t TYPE R F Refrigerants 22, 410 hatleff, SE Flare & ODF Solder onnections Splan Type R valve is a small brass body, externally adjustable valve with balanced pt construction. The R valves are available f replacement of types I and I valves. These valves contain internal check valves to allow reverse flow on heat pump applications. This eliminates the need f an external check valve piped around the TEV f reverse flow. The R valve can be used on heat pump and air conditioning (cooling only) applications. This allows you to reduce inventy by using the same valve to replace the I, I and I valves. The R valves can even be used to replace the RI valve (non- RP versions only). Outlet onnections 1/2 SE, 1/2 ODF, 5/8 ODF Mating Distributs (See ulletin 20-10) D260, D262, 160, 1605, 1606, 1608, 1620, 1622, 1650(R), 1651(R) F complete details of construction, see page 5. Type R SPEIFITIONS ELEMENT SIZE NO. 4 (R-22) ND NO. 45 (R-410), KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) VLVE TYPE EXTERNL EQULIZER W, E NOMINL PITY Tons of THERMOSTTI ELEMENT SIZE NO. THERMOSTTI HRGES VILLE TUING LENGTH INLET RVE-1-G 1 RVE-1-1/2-G 1-1/2 /8 SE RVE-2-G 2 /8 ODF 1/4 SE RVE--G 4 VG 1/4 ODF RVE-4-G 4 1/2 ODF RVE-5-G 5 1/2 SE RVE-6-G 6 0 in. 1/2 ODF RZE-1-G ONNETIONS - Inches Q SE Flare/ R ODF Solder lue figures are standard and will be furnished unless otherwise specified. OUTLET 1/2 SE 1/2 ODF 1/2 ODF 1/2 SE 5/8 ODF RZE-1-1/2-G 1-1/2 /8 ODF 1/2 ODF RZE-2-G (Z) RZE--G 1/4 ODF 45 ZG RZE-4-G 4 1/2 ODF 1/2 ODF RZE-5-G 5 RZE-6-G 6 1/2 ODF 5/8 ODF Q Valves are also available as special der with hatleff connections. W Valves with SE inlet and outlet fittings are available only with the 1/4 SE flare external equalizer; valves w ith ODF fittings are available only with the 1/4 ODF external equalizer. E Valves with hatleff fittings are available only with the OD X 24 long tube with flare and nut external equalizer. R ODF Solder on Type R valves indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 1/2 ODF will receive 1/2 OD tubing. NET 1-1/4 lbs. 568 g SHIPPING 1-1/2 lbs. 680 g DIMENSIONS ONNETIONS - Inches 1.94 ap Tube 0 VLVE TYPE FITTING SIZE D /8 SE /2 SE R /8 ODF /2 ODF /8 ODF R hatleff Fitting E UL SIZES - Inches HRGES G 0.75 OD x /4 ODF onnection D 0 Top View hatleff Fitting Option E

14 t TYPE ER ULLETIN Page 1 F Refrigerants 22, 410 ODF Solder onnections Splan Type ER valve is a small brass bar body, externally adjustable with ODF solder connections, a replaceable thermostatic element, and balanced pt construction. The ER valve is designed f R-22 and R-410 air conditioning and heat pump applications and is ideal f replacing I, I, I and RI (non-rp version only) valves. This valve type has two body styles: a small body which provides capacities up to 8 tons R-22 and R-410, and a large body style which extends capacities to 12 tons R-22 and 15 tons R-410. Replacement elements available f these valves are the following: Refrigerant R-22, Element Kit Number KT-4-VG VP100 f the small body style and KT-45-5-VG VP100 f the large body, and Refrigerant R-410, Element Kit Number KT-45-ZG ZP180 f the small body style and KT-45-5-ZG ZP180 f the large body style. This valve may also be applied in bi-directional applications. Outlet onnections 1/2 ODF, 5/8 ODF, 7/8 ODF, 1- ODF Mating Distributs (See ulletin 20-10) D260, D262, 1620, 1622, 1112, 111, 1115, 1116, 115, 116, 117, 1651(R), 165(R), 1655(R) F complete details of construction, see page 5. Type ER SPEIFITIONS ELEMENT SIZE NO. 4 (R-22), NO. 45 (R-410), ND NO. 45-5, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 410 (Z) VLVE TYPE NOMINL PITY Tons of THERMOSTTI ELEMENT SIZE NO. THERMOSTTI HRGES VILLE TUING LENGTH ONNETIONS -Inches Q ODF Solder Not all connection combinations are available. INLET OUTLET ERVE-1 1 ERVE-1-1/2 1-1/2 /8 1/2 ERVE-2 2 ERVE- 1/2 5/8 4 ERVE-4 4 VG 60 in. /8 1/2 1/2, 5/8 7/8 ERVE-5 5 VP m ERVE-6 6 5/8 7/8 1/2 ERVE-8 8 ERVE / /8 ERVE ERZE-1 1 ERZE-1-1/2 1-1/2 /8 1/2 ERZE-2 2 ERZE- 1/2 5/8 45 ERZE-4 4 ZG 60 in. /8 1/2 1/2, 5/8 7/8 ERZE-5 5 ZP m ERZE-6 6 5/8 7/8 1/2 ERZE-8 8 7/8 ERZE-12-1/2 12-1/2 ERZE /8 1- Q ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 1/2 ODF will receive 1/2 OD tubing. NET 1 lb. 454 g 1 lb. 454 g SHIPPING 1-1/2 lbs. 680 g 1-1/2 lbs. 680 g

15 Page 14 ULLETIN t TYPE ER F Refrigerants 22, 410 ODF Solder onnections TYPE ER with NUMER 4 and 45 ELEMENT Top View DIMENSIONS - ONNETIONS NOMINL PITY 1-1/ FITTING SIZE INLET OUTLET /8 1/2 1/2.25/ /6.50 5/8 7/ /8 5/ Diameter D E F E.77/ / / / / / / / / / / / / / / / ap Tube 60 UL SIZES HRGES VP100, ZP180 G D F OD x x OD x x 50.8 TYPE ER with NUMER 45-5 ELEMENT DIMENSIONS - ONNETIONS NOMINL PITY / FITTING SIZE INLET OUTLET 5/8.25/ /6.50 Diameter /8 1- D E F / E 15.9/ / / / / ap Tube 60 D F

16 ULLETIN Page 15 t TYPE F & EF F Refrigerants 22, 14a, 404, 507 SE Flare & ODF Solder onnections Splan Type F with SE flare connections Type EF with ODF solder connections are small brass bar body valves with identical internal construction and replaceable thermostatic elements. The Type F valve has a removable 100 mesh strainer as a standard feature. The Type EF has a 60 x 50 mesh insert strainer. These valves are designed f small refrigeration systems such as refrigerated cases, coolers, and freezers where space is limited and an external adjustment is desired. Outlet onnections /8 SE, 1/2 SE, /8 ODF, 1/2 ODF Mating Distributs (See ulletin 20-10) D260, D262, 160, 1605, 1606, 1608, 1650(R) F complete details of construction, see page 5. Type F Type EF SPEIFITIONS ELEMENT SIZE NO. 4, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Internal TYPE F SE Flare TYPE EF ODF Solder Internal NOMINL PITY Tons of FV-1/5 FVE-1/5 EFV-1/5 EFVE-1/5 1/5 FV-1/ FVE-1/ EFV-1/ EFVE-1/ 1/ FV-1/2 FVE-1/2 EFV-1/2 EFVE-1/2 1/2 FV-1 FVE-1 EFV-1 EFVE-1 1 FV-1-1/2 FVE-1-1/2 EFV-1-1/2 EFVE-1-1/2 1-1/2 FVE-2 EFVE-2 2 FV-2-1/2 EFV-2-1/2 2-1/2 EFVE- FJ- FJE- EFJ- EFJE- FJ-1/6 FJE-1/6 EFJ-1/6 EFJE-1/6 1/6 FJ-1/4 FJE-1/4 EFJ-1/4 EFJE-1/4 1/4 FJ-1/2 FJE-1/2 EFJ-1/2 EFJE-1/2 1/2 FJ-1 FJE-1 EFJ-1 EFJE-1 1 FJ-1-1/2 FJE-1-1/2 EFJ-1-1/2 EFJE-1-1/2 1-1/2 FJE-2 EFJE-2 2 FS- FSE- EFS- EFSE- FS-1/6 FSE-1/6 EFS-1/6 EFSE-1/6 1/6 FS-1/4 FSE-1/4 EFS-1/4 EFSE-1/4 1/4 FS-1/2 FSE-1/2 EFS-1/2 EFSE-1/2 1/2 FS-1 FSE-1 EFS-1 EFSE-1 1 FS-1-1/2 FSE-1-1/2 EFS-1-1/2 EFSE-1-1/2 1-1/2 FSE-2 EFSE-2 2 FP- FPE- EFP- EFPE- FP-1/6 FPE-1/6 EFP-1/6 EFPE-1/6 1/6 FP-1/4 FPE-1/4 EFP-1/4 EFPE-1/4 1/4 FP-1/2 FPE-1/2 EFP-1/2 EFPE-1/2 1/2 FP-1 FPE-1 EFP-1 EFPE-1 1 THERMOSTTI HRGES VILLE TUING LENGTH ONNETIONS - Inches SE Flare / W ODF Solder lue figures are standard and will be furnished unless otherwise specified. FP-1-1/2 FPE-1-1/2 EFP-1-1/2 EFPE-1-1/2 1-1/2 /8 E 1/2 FPE-2 EFPE-2 2 Q The /8 SE inlet fitting has a long taper on the flare surface. /8 x 1/4 reducing flare nut will allow 1/4 OD tubing to be attached to this fitting. W ODF Solder on Type EF valves indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 1/2 ODF will receive 1/2 OD tubing. E Nominal 1 ton and larger F valves f R-14a, R-404 and R-507 type refrigerants, and nominal 1-1/2 ton and larger f R-22 refrigerant require /8 SE Flare /8 ODF inlet, minimum. Z ZP40 Z ZP40 Z ZP40 0 in. 760 INLET OUTLET 1/4 /8 Q /8 1/2 /8 E 1/2 1/4 /8 Q /8 1/2 /8 E 1/2 1/4 /8 Q /8 1/2 /8 E 1/2 1/4 /8 Q /8 1/2 NET 1 lb. 454 g SHIPPING 1-1/2 lbs. 680 g

17 Page 16 ULLETIN t TYPE F & EF F Refrigerants 22, 14a, 404, 507 SE Flare & ODF Solder onnections SE FLRE DIMENSIONS SE ONNETIONS - Inches FITTING SIZE 1/4 SE Elbow /8 SE Elbow /8 SE /2 SE 1.80 UL SIZES - Inches HRGES 22 14a OD x.00 Z & ZP Series 0.50 OD x OD x /4 SE Inlet P/N /8 SE Inlet P/N /4 SE Fitting Top View ODF SOLDER DIMENSIONS ODF ONNETIONS - Inches 1.94 FITTING SIZE 1/4 ODF /8 ODF /2 ODF UL SIZES - Inches HRGES 22 14a OD x.00 Z & ZP Series 0.50 OD x OD x.00 1/4 ODF onnection /4 ODF Insert P/N /8 ODF Insert P/N Top View 1.81

18 t TYPE Q & Q The Splan Q & Q series are replaceable cartridge style valves designed f small refrigeration systems, such as refrigerated cases, coolers, and freezers. The externally equalized versions of these valves are ideal f air conditioning and heat pump systems. Q valves are balanced pted, engineered specifically f systems with a wide range of operating conditions and may be applied on bi-directional applications. Q & Q valves are supplied as three individual component parts: the thermostatic element, the valve body, and the replaceable cartridge ifice. The interchangeable nature of the Q & Q family make it ideal f reducing inventy, while increasing valve options so, the right valve is always on hand. ODY FETURES Q & Q brass body type valves feature Splan s traditional knife edge, metal-to-metal thermostatic element to valve body construction, which insures a leak-proof joint. SELETIVE HRGES Splan selective thermostatic charges are specifically designed f low temperature, medium temperature, and air conditioning applications. The elements are manufactured with a large flat diaphragm to reduce diaphragm stresses and provide precise control. nd, because Q & Q valve bodies and thermostatic elements are supplied as independent components, the installer is able to select the best possible thermostatic charge f the application. INTERNL PORT DESIGN Refrigerant flow through the valve pt opposes the pin movement in all type Q and Q valves. This provides improved stability at light loads, when the pin modulates to a position close to the pt. dditionally, charge migration, is reduced eliminated by the Q & Q valve design. y engineering the liquid flow to enter through the top of the valve body, the liquid refrigerant warms the thermostatic element and minimizes the potential f charge migration. ULLETIN Page 17 F Refrigerants 22, 14a, 404, 410*, 507 SE Flare & Extended ODF Solder onnections *Type Q, EQ, and SQ are not approved f R-410 applications. TYPE onventional Pt TYPE alanced Pt SELETING OMPONENTS ODY F complete details of construction, see page 5. U.S. Patent No. 5,28,219 Replaceable U.S. Patent No. 5,22,015 Flare onnections Extended Solder onnections Extended Solder onnections with Fged Inlet and Replaceable Q SE (Internally Equalized) EQ ODF (Internally Equalized) SQ ODF (Internally Equalized) QE SE (ly Equalized) EQE ODF (ly Equalized) SQE ODF (ly Equalized) Q SE (Internally Equalized) EQ ODF (Internally Equalized) SQ ODF (Internally Equalized) QE SE (ly Equalized) EQE ODF (ly Equalized) SQE ODF (ly Equalized) U.S. Patent No. 5,28,219, Replaceable P/N U.S. Patent No. 5,22,015

19 Page 18 ULLETIN t TYPE Q & Q F Refrigerants 22, 14a, 404, 410*, 507 SE Flare & Extended ODF Solder onnections *Type Q, EQ, and SQ are not approved f R-410 applications. RTRIDGE Q RTRIDGE SERVIE KIT PRT NUMER Top surface is col coded to identify cartridge capacity apacity code on cartridge. 2 Q-0 - Red Qty. Q-1 - Yellow Qty. 5 Q-2 - Green Qty. 5 Q- - lue Qty. 5 Q-4 - Pink Qty. SPORLN llen Wrench Oil ottle 6 Identification tag with cartridge number (bends around capillary tubing). Q-5 - lack Qty. Pushrods Qty. 4 Q-6 - White Qty. INDIVIDUL REPLEMENT PRTS PRT NUMER SIZE OLOR ODE Q-0 Q-1 Q-2 Q- Q-4 Q-5 Q-6 RTRIDGE and I.D. TG Red Yellow Green lue Pink lack White MISELLNEOUS PRTS O-1 Oil ottle (With Oil) W-1 4 llen Wrench SK-1 Q artridge Service Kit (Empty) Q artridge Service Kit (omplete as noted above) PITIES NOMINL PITY (TONS) of SPORLN VLVE TO E REPLED Q VLVE RTRIDGE R-12 R-22, R-422D R-14a R-401 R-402 R-404 R-410 R-502 R-507 SIZE OLOR ODE 1/4 1/6 1/ 1/6 1/6 1/6 1/6 1/6 1/6 0 Red 1/4 1/2 /4 1/4 1/4 1/4 1/4 1/4 1/4 1 Yellow 1/2 1 1/2 1/2 1/2 1/2 1/2 1/2 2 Green 1 1-1/ lue 1-1/ /2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 1-1/2 4 Pink lack 2-1/ /2 2-1/2 5 6 White NOT PPROVED Q RTRIDGE SERVIE KIT PRT NUMER Top surface is col coded to identify cartridge capacity. apacity code on cartridge. SPORLN Identification tag with cartridge number (bends around capillary tubing). Q- - Red Qty. 2 Q artridge Tool Q SPORLN Q- - Yellow Qty. 4 Q- - lue Qty. 4 Q- - Pink Qty. 1 Oil ottle Q- - Pink Qty. 2 Q- - White Qty. 2 INDIVIDUL REPLEMENT PRTS PRT NUMER SIZE OLOR ODE Q- Q- Q- Q- Q- RTRIDGE and I.D. TG* MISELLNEOUS PRTS Red Yellow lue Pink White O-1 Oil ottle (With Oil) Q artridge Tool Q artridge Service Kit SK-1 (Empty) Q artridge Service Kit (omplete as noted above) *Q with 15 (15% bleed pt) is available. PITIES R-12 1/5 1/4 1/ 1/ /4 1-/4 2 R-22, R-422D 1/ 1/2 2/ /4 1-1/2 1-/4-1/4 5-1/2 NOMINL PITY (TONS) of SPORLN VLVE TO E REPLED Q VLVE RTRIDGE R-14a R-401 R-402 R-404 R-410 R-502 R-507 SIZE OLOR ODE 1/5 1/4 1/ 1/ /4 1-/4 1/5 1/4 1/ 1/ /4 1-/ /5 1/4 1/ 1/ / /4 1/5 1/4 1/ 1/ / /4 1/4 1/ 1/2 /4 1 1-/4 2-1/ /5 1/4 1/ 1/ / /4 1/5 1/4 1/ 1/ / /4 Red Yellow lue Pink White

20 ULLETIN Page 19 t TYPE Q & Q F Refrigerants 22, 14a, 404, 410*, 507 SE Flare & Extended ODF Solder onnections ELEMENT SPORLN VLVE O WSHINGTON, MO MDE IN U.S. of. R-22 KT-4-V 4 V 5207 Element Label PPLITION 12 apillary Tube Length (standard = 5 ft.) Date ode Label (by week and year of manufacture) KT 4 V bbreviation f Kit ir onditioning oercial 50 F to -10 F Low Temperature 0 F to -40 F Element Size Number 22, 422D Refrigerant ode Q ulb Thermostatic harge Q While many new refrigerants and refrigerant blends have a unique letter code, many use the same thermostatic element as the traditional refrigerant they replace. Refer to the table below to select the crect thermostatic element. REOMMENDED THERMOSTTI ELEMENTS** 14a SPORLN ODE ELEMENT LEL OLOR ODE F R-12 Yellow V R-22, R-422D Green J R-14a lue X R-401 Pink L R-402 Sand S R-404 Orange V R-407 Green N R-407 Light rown R R-408 Purple F R-409 Yellow Z R-410 Pink R R-502 Purple P R-507 Teal THERMOSTTI ELEMENT SYSTEM MOP psig X X X X KT-4-JP60 50 X X X KT-4-VP X X X KT-4-VG X X X KT-4-SP X KT-45-ZG X KT-45-ZP X X X X KT-4-J X X X KT-4-V X X X KT-4-S X X KT-4-P X KT-4-JZ X KT-4-JZP 12 X KT-4-VZ X KT-4-VZP40 0 X X X X X KT-4-SZ X X X X X KT-4-SZP 5 **PPLITION FTORS: 1. The Splan Type ZP thermostatic charges have essentially the same characteristics as the conventional Z cross charges with one exception: they produce a pressure limit MOP. The ZP charges are not intended as replacements f the Z charges - they should only be used where a definite pressure limit is required to prevent mot overloading. 2. ll air conditioning and heat pump charges are intended f use with externally equalized valves.. F dual temperature applications, use the charge. 4. The charge may be used on applications down to -0 F on R-22, R-404 and R R-410 elements f use with Q, EQ, and SQ only. ORDERING INSTRUTIONS VLVE NOMENLTURE QE /8 x 1/2 x 1/4 SE Q 2 KT-4 V 5 Valve Type Q, EQ, SQ Internally Equalized QE, EQE, SQE ly Equalized onnection Size and Style: Inlet x Outlet x artridge Type artridge Size Element Kit KT-4 Refrigerant ode (See above) Thermostatic harge QE /8 x 1/2 x 1/4 SE Q KT-4 V 5 Valve Type Q, EQ, SQ Internally Equalized QE, EQE, SQE ly Equalized ODY RTRIDGE ELEMENT ODY RTRIDGE ELEMENT onnection Size and Style: Inlet x Outlet x artridge Type artridge Size Element Kit KT-4 KT-45 (R-410 only) *Type Q, EQ, and SQ are not approved f R-410 applications. Refrigerant ode (See above) Thermostatic harge apillary Tube Length apillary Tube Length

21 Page 20 ULLETIN t TYPE Q & Q F Refrigerants 22, 14a, 404, 410*, 507 SE Flare & Extended ODF Solder onnections *Type Q, EQ, and SQ are not approved f R-410 applications. Q SPEIFITIONS ELEMENT SIZE NO. 4, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Internal Q SE Flare W ODY TYPE - RTRIDGE Internal Q Extended ODF Solder W Internal Q W RTRIDGE NOMINL PITY Tons of Q-0 QE-0 EQ-0 EQE-0 SQ-0 SQE-0 0 1/ Q-1 QE-1 EQ-1 EQE-1 SQ-1 SQE-1 1 /4 Q-2 QE-2 EQ-2 EQE-2 SQ-2 SQE Q- QE- EQ- EQE- SQ- SQE- 1-1/2 Q-4 QE-4 EQ-4 EQE-4 SQ-4 SQE /2 Q-5 QE-5 EQ-5 EQE-5 SQ-5 SQE-5 5-1/2 Q-6 QE-6 EQ-6 EQE-6 SQ-6 SQE Q-0 QE-0 EQ-0 EQE-0 SQ-0 SQE-0 0 1/6 Q-1 QE-1 EQ-1 EQE-1 SQ-1 SQE-1 1 1/4 Q-2 QE-2 EQ-2 EQE-2 SQ-2 SQE-2 2 1/2 Q- QE- EQ- EQE- SQ- SQE- 1 Q-4 QE-4 EQ-4 EQE-4 SQ-4 SQE /2 Q-5 QE-5 EQ-5 EQE-5 SQ-5 SQE Q-6 QE-6 EQ-6 EQE-6 SQ-6 SQE /2 Q-0 QE-0 EQ-0 EQE-0 SQ-0 SQE-0 0 1/6 Q-1 QE-1 EQ-1 EQE-1 SQ-1 SQE-1 1 1/4 Q-2 QE-2 EQ-2 EQE-2 SQ-2 SQE-2 2 1/2 Q- QE- EQ- EQE- SQ- SQE- 1 Q-4 QE-4 EQ-4 EQE-4 SQ-4 SQE /2 Q-5 QE-5 EQ-5 EQE-5 SQ-5 SQE Q-6 QE-6 EQ-6 EQE-6 SQ-6 SQE-6 6 Q-0 QE-0 EQ-0 EQE-0 SQ-0 SQE-0 0 1/6 Q-1 QE-1 EQ-1 EQE-1 SQ-1 SQE-1 1 1/4 Q-2 QE-2 EQ-2 EQE-2 SQ-2 SQE-2 2 1/2 Q- QE- EQ- EQE- SQ- SQE- 1 Q-4 QE-4 EQ-4 EQE-4 SQ-4 SQE /2 Q-5 QE-5 EQ-5 EQE-5 SQ-5 SQE Q-6 QE-6 EQ-6 EQE-6 SQ-6 SQE-6 6 THERMOSTTI HRGES VILLE Refer to Recoended Thermostatic Elements on Page 19 TUING LENGTH 5 ft. 1.5 m ONNETIONS Inches lue figures are standard and will be furnished unless otherwise specified. INLET x OUTLET Q & QE Only 1/4 x /8 SE 90 ngle Inlet 1/4 x 1/2 SE 90 ngle Inlet /8 x 1/2 SE 90 ngle Inlet EQ Only /8 x 1/2 ODF Straight Thru EQE Only /8 x 1/2 ODF Straight Thru /8 x 5/8 ODF Straight Thru 1/2 x 5/8 ODF Straight Thru 1/2 x 7/8 ODF Straight Thru SQ & SQE Only /8 x 1/2 ODF 90 ngle Inlet NET 1 lb. 454 g SHIPPING 1-1/2 lbs. 680 g Q SPEIFITIONS ELEMENT SIZE NO. 4 (R-22) and N0. 45 (R-410), KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 410 (Z) 507 (P) 402 (L) Internal Q SE Flare W ODY TYPE - RTRIDGE Internal Q Extended ODF Solder W Internal Q W Q Valves listed in the column are NOT VILLE with MOP type air conditioning charges. W Standard 1/4 SE (Q and Q ody), 1/4 ODF (SQ, SQ, EQ and EQ ody). E The /8 SE inlet fitting has a long taper on the flare surface. /8 x 1/4 reducing flare nut will allow 1/4 OD tubing to be attached to this fitting. R ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 1/2 ODF will receive 1/2 OD tubing. RTRIDGE NOMINL PITY Tons of Q- QE- EQ- EQE- SQ- SQE- 1/ Q- QE- EQ- EQE- SQ- SQE- 1/2 2/ Q- QE- EQ- EQE- SQ- SQE- /4 1-1/2 Q- QE- EQ- EQE- SQ- SQE- 1-/4 Q- QE- EQ- EQE- SQ- SQE- -1/4 5-1/2 Q- QE- EQ- EQE- SQ- SQE- 1/5 Q- QE- EQ- EQE- SQ- SQE- 1/4 1/ Q- QE- EQ- EQE- SQ- SQE- 1/2 1 Q- QE- EQ- EQE- SQ- SQE- 1-1/4 1-/4 Q- QE- EQ- EQE- SQ- SQE- 2 Q- QE- EQ- EQE- SQ- SQE- 1/5 Q- QE- EQ- EQE- SQ- SQE- 1/4 1/ Q- QE- EQ- EQE- SQ- SQE- 1/2 1 Q- QE- EQ- EQE- SQ- SQE- 1-1/4 2 Q- QE- EQ- EQE- SQ- SQE- 2-1/4 Q- QE- EQ- EQE- SQ- SQE- 1/4 1/ Q- QE- EQ- EQE- SQ- SQE- 1/2 /4 Q- QE- EQ- EQE- SQ- SQE- 1 1-/4 Q- QE- EQ- EQE- SQ- SQE- 2-1/12 Q- QE- EQ- EQE- SQ- SQE- 4 6 Q- QE- EQ- EQE- SQ- SQE- 1/5 Q- QE- EQ- EQE- SQ- SQE- 1/4 1/ Q- QE- EQ- EQE- SQ- SQE- 1/2 1 Q- QE- EQ- EQE- SQ- SQE- 1-1/4 2 Q- QE- EQ- EQE- SQ- SQE- 2-1/4 THERMOSTTI HRGES VILLE Refer to Recoended Thermostatic Elements on Page 19 TUING LENGTH 5 ft. 1.5 m ONNETIONS Inches lue figures are standard and will be furnished unless otherwise specified. INLET x OUTLET Q & QE 1/4 x /8 SE 90 ngle Inlet 1/4 x 1/2 SE 90 ngle Inlet /8 x 1/2 SE E 90 ngle Inlet EQ Only /8 x 1/2 ODF R Straight Thru EQE Only /8 x 1/2 ODF R Straight Thru /8 x 1/2 ODF R 90 ngle Inlet 1/2 x 5/8 ODF R Straight Thru 1/2 x 7/8 ODF R Straight Thru SQ & SQE Only /8 x 1/2 ODF R 90 ngle Inlet NET 1 lb. 454 g SHIPPING 1-1/2 lbs. 680 g

22 t TYPE Q & Q ULLETIN Page 21 F Refrigerants 22, 14a, 404, 410*, 507 SE Flare & Extended ODF Solder onnections *Type Q, EQ, and SQ are not approved f R-410 applications. TYPE QE TYPE QE 1.94 QE & QE DIMENSIONS ONNETIONS - Inches 1.94 FITTING SIZE 1/4 SE.9 Inlet P/N /8 SE Inlet P/N /4 SE, 90 ngle /8 SE, 90 ngle /8 SE /2 SE 1.80 Top View 60 1/4 SE.9 Inlet P/N /8 SE Inlet P/N TYPE EQE TYPE EQE /8 ODF Insert P/N /2 ODF Insert P/N /8 ODF Insert P/N /2 ODF Insert P/N EQE & EQE DIMENSIONS ONNETIONS - Inches FITTING SIZE Top View 60 / / / / TYPE SQE TYPE SQE Removable P/N Top View 60 Removable P/N UL SIZES - Inches HRGES 22 14a OD x OD x.00 Z & ZP Series 0.50 OD x OD x OD x.00 P Series 0.50 OD x.00 G 0.75 OD x OD x 2.00

23 Page 22 ULLETIN t TYPE G F Refrigerants 22, 14a, 404, 507 SE Flare onnections Splan Type G valve is a fged brass body, externally adjustable valve with SE flare connections. The thermostatic element is replaceable, and the inlet connection has a removable 100 mesh strainer. This valve is designed f small refrigeration systems such as refrigerated cases, coolers and freezers. In addition to refrigeration applications, the externally equalized Type G valve may be used f small capacity air conditioning and heat pump units. Outlet onnections 1/2 SE Mating Distributs (See ulletin 20-10) 160, 1605, 1606, 1608, 1650(R) F complete details of construction, see page 5. Type G SPEIFITIONS ELEMENT SIZE NO. 5, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Internal Q GP-1-1/2 GPE-1-1/2 1-1/2 GPE-2 2 Q Valves listed in this column NOT VILLE with MOP Type air conditioning charges. W The /8 SE inlet fitting has a long taper on the flare surface. /8 x 1/4 reducing flare nut will allow 1/4 OD tubing to be attached to this fitting. 1/4 SE onnection VLVE TYPE 1/4 SE.25 NOMINL PITY Tons of 1.25 THERMOSTTI HRGES VILLE TUING LENGTH ONNETIONS - Inches SE Flare lue figures are standard and will be furnished unless otherwise specified. Flare INLET OUTLET GV-1/5 GVE-1/5 1/5 GV-1/ GVE-1/ 1/ GV-1/2 GVE-1/2 1/2 GV-/4 GVE-/4 /4 GV-1 GVE-1 1 GV-1-1/2 GVE-1-1/2 1-1/2 GVE-2 2 GV-2-1/2 2-1/2 GVE- GJ- GJE- GJ-1/6 GJE-1/6 1/6 GJ-1/4 GJE-1/4 1/4 GJ-1/2 GJE-1/2 1/2 GJ-1 GJE-1 1 GJ-1-1/2 GJE-1-1/2 1-1/2 GJE-2 2 GS- GSE- GS-1/6 GSE-1/6 1/6 GS-1/4 GSE-1/4 1/4 GS-1/2 GSE-1/2 1/2 GS-1 GSE-1 1 GS-1-1/2 GSE-1-1/2 1-1/2 GSE-2 2 GP- GPE- GP-1/6 GPE-1/6 1/6 GP-1/4 GPE-1/4 1/4 GP-1/2 GPE-1/2 1/2 GP-1 GPE-1 1 Refer to Recoended Thermostatic harges on page 5 ft. 1.5 m 1/4 /8 W 1/4 /8 W /8 W 1/4 /8 W 1/4 /8 W /8 W 1/4 /8 W 1/4 /8 W /8 W 1/4 /8 W 1/4 /8 W /8 W Removable P/N /2 NET 2 lbs kg 1.56 with external equalizer 1.68 SHIPPING lbs. 1.6 kg DIMENSIONS UL SIZES - Inches Top View 1.44 HRGES 22 14a OD x.50 Z & ZP Series 0.50 OD x OD x.50 X 0.75 OD x OD x 4.00 P Series 0.50 OD x.50 VG 0.75 OD x /4 SE Inlet P/N Diameter of Type X harge Diaphragm ase is.62.06

24 t TYPE EG ULLETIN Page 2 F Refrigerants 22, 14a, 404, 507 ODF Solder onnections Splan Type EG valve is a fged brass body, externally adjustable valve with ODF solder connections. The thermostatic element is replaceable, and the inlet connection has a removable 100 mesh strainer which can be cleaned and/ replaced without removing the valve from the line. This valve is designed f small refrigeration systems such as refrigerated cases, coolers and freezers. In addition to refrigeration applications, the externally equalized Type EG valve may be used f small capacity air conditioning and heat pump units. Outlet onnections 1/2 ODF Mating Distributs (See ulletin 20-10) D260, D262 SPEIFITIONS ELEMENT SIZE NO. 5, KNIFE EDGE JOINT F complete details of construction, see page 5. Type EG Replaceable U.S. Patent No. 5,22,015 (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Internal Q EGPE-2 2 Q Valves listed in this column NOT VILLE with MOP Type air conditioning charges. W ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 1/2 ODF will receive 1/2 OD tubing. 1/4 ODF onnection VLVE TYPE.25 NOMINL PITY Tons of 1. THERMOSTTI HRGES VILLE TUING LENGTH ONNETIONS - Inches W ODF Solder lue figures are standard and will be furnished unless otherwise specified. 1/4 ODF Solder INLET OUTLET EGV-1/5 EGVE-1/5 1/5 EGV-1/ EGVE-1/ 1/ EGV-1/2 EGVE-1/2 1/2 EGV-/4 EGVE-/4 /4 EGV-1 EGVE-1 1 EGV-1-1/2 EGVE-1-1/2 1-1/2 EGVE-2 2 EGV-2-1/2 2-1/2 EGVE- EGJ- EGJE- EGJ-1/6 EGJE-1/6 1/6 EGJ-1/4 EGJE-1/4 1/4 EGJ-1/2 EGJE-1/2 1/2 EGJ-1 EGJE-1 1 EGJ-1-1/2 EGJE-1-1/2 1-1/2 EGJE-2 2 EGS- EGSE- EGS-1/6 EGSE-1/6 1/6 EGS-1/4 EGSE-1/4 1/4 EGS-1/2 EGSE-1/2 1/2 EGS-1 EGSE-1 1 EGS-1-1/2 EGSE-1-1/2 1-1/2 EGSE-2 2 EGP- EGPE- EGP-1/6 EGPE-1/6 1/6 EGP-1/4 EGPE-1/4 1/4 EGP-1/2 EGPE-1/2 1/2 EGP-1 EGPE-1 1 EGP-1-1/2 EGPE-1-1/2 1-1/2 Refer to Recoended Thermostatic harges on page 5 ft. 1.5 m *Removable P/N /8 1/ NET 2 lbs kg SHIPPING lbs. 1.6 kg DIMENSIONS UL SIZES - Inches Top View HRGES 22 14a OD x.50 Z & ZP Series 0.50 OD x OD x.50 X 0.75 OD x OD x 4.00 P Series 0.50 OD x.50 VG 0.75 OD x Diameter of Type X harge Diaphragm ase is.62 * Type EG valves manufactured pri to June 1994 use a smaller inlet strainer, P/N , which has a 1/2 brass hex head. urrent Type EG valves use inlet strainer P/N which has a 5/8 brass hex head. These strainers are not interchangeable. The is available as a replacement part. The is no longer available..06

25 Page 24 ULLETIN t TYPE F F Refrigerants 22, 14a, 404, 507 SE Flare onnections Splan Type F valve is a small brass bar body valve with SE flare connections and balanced pt construction. This valve has the same exteri dimensions as the Type F valve. The thermostatic element is replaceable, and the inlet connection has a removable 100 mesh strainer. The balanced pt construction makes this valve ideally suited f small capacity refrigeration applications which operate over widely varying operating conditions. Outlet onnections 1/2 SE Mating Distributs (See ulletin 20-10) 160, 1605, 1606, 1608, 1650(R) F complete details of construction, see page 5. Type F SPEIFITIONS ELEMENT SIZE NO. 4, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) VLVE TYPE Internal SE Flare PORT SIZE NOMINL PITY Tons of THERMOSTTI HRGES VILLE TUING LENGTH Q The /8 SE inlet fitting has a long taper on the flare surface. /8 x 1/4 reducing flare nut will allow 1/4 OD tubing to be attached to this fitting. ONNETIONS - Inches SE Flare lue figures are standard and will be furnished unless otherwise specified. INLET FV- FVE- 1/ 1/4 /8 Elbow Q FV- FVE- 1/2 2/ FV- FVE- /4 1-1/2 Z 1/4 /8 Elbow Q FV- FVE- 1-/4 ZP40 /8 Elbow FV- FVE- -1/4 5-1/2 FJ- FJE- 1/5 FJ- FJE- 1/4 1/ 1/4 /8 Elbow Q FJ- FJE- 1/2 1 1/4 /8 Elbow Q FS- FSE- 1/5 760 FS- FSE- 1/4 1/ FJ- FJE- 1-1/4 1-/4 FJ- FJE- 2 0 in. /8 Elbow 1/4 /8 Elbow Q FS- FSE- 1/2 1 Z 1/4 /8 Elbow Q FS- FSE- 1-1/4 2 ZP FS- FSE- 2-1/4 /8 Elbow FP- FPE- 1/5 1/4 /8 Elbow Q FP- FPE- 1/4 1/ FP- FPE- 1/2 1 Z 1/4 /8 Elbow Q FP- FPE- 1-1/4 2 ZP /8 Elbow FP- FPE- 2-1/4 OUTLET /8 1/2 EXTERNL EQULIZER 1/4 NET 1 lb. 454 g SHIPPING 1-1/2 lbs. 680 g DIMENSIONS ONNETIONS - Inches FITTING SIZE SE Flare 1/4 Elbow /8 Elbow /8 SE /2 SE /4 SE onnection Top View UL SIZES - Inches HRGES 22 14a OD x.00 Z & ZP Series 0.50 OD x OD x.00 1/4 SE Removable P/N /8 SE Removable P/N

26 t TYPE SF & EF ULLETIN Page 25 F Refrigerants 22, 14a, 404, 507 Extended Solder onnections Splan Types SF & EF are small brass bar body valves with Extended ODF solder connections and the same balanced pt construction as the Type F valve. oth valves have replaceable thermostatic elements. The Type EF has a 100 mesh insert strainer. The Type SF has a 100 mesh removable strainer that can be cleaned and/ replaced while the valve is still soldered to the system tubing. The balanced pt construction makes these valves ideally suited f small capacity refrigeration applications which operate over widely varying conditions. Outlet onnections 1/2 ODF, 5/8 ODF Mating Distributs (See ulletin 20-10) D260, D262, 1620, 1622, 1651(R) F complete details of construction, see page 5. Type SF Type EF SPEIFITIONS ELEMENT SIZE NO. 4, KNIFE EDGE JOINT Replaceable U.S. Patent No. 5,22,015 (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) TYPE SF Extended ODF Solder with replaceable strainer Internal TYPE EF Extended ODF Solder Internal PORT SIZE NOMINL PITY RNGE Tons of SFV- SFVE- EFV- EFVE- 1/ SFV- SFVE- EFV- EFVE- 1/2 2/ SFV- SFVE- EFV- EFVE- /4 1-1/2 SFV- SFVE- EFV- EFVE- 1-/4 SFV- SFVE- EFV- EFVE- -1/4 5-1/2 SFJ- SFJE- EFJ- EFJE- 1/5 SFJ- SFJE- EFJ- EFJE- 1/4 1/ SFJ- SFJE- EFJ- EFJE- 1/2 1 SFJ- SFJE- EFJ- EFJE- 1-1/4 1-/4 SFJ- SFJE- EFJ- EFJE- 2 SFS- SFSE- EFS- EFSE- 1/5 SFS- SFSE- EFS- EFSE- 1/4 1/ SFS- SFSE- EFS- EFSE- 1/2 thur 1 SFS- SFSE- EFS- EFSE- 1-1/4 2 SFS- SFSE- EFS- EFSE- 2-1/4 SFP- SFPE- EFP- EFPE- 1/5 SFP- SFPE- EFP- EFPE- 1/4 1/ SFP- SFPE- EFP- EFPE- 1/2 1 SFP- SFPE- EFP- EFPE- 1-1/4 2 SFP- SFPE- EFP- EFPE- 2-1/4 THERMOSTTI HRGES VILLE TUING LENGTH ONNETIONS - Inches Q Extended ODF Solder lue figures are standard and will be furnished unless otherwise specified. INLET OUTLET EXTERNL EQULIZER Z ZP40 Z ZP Z ZP 1/2 0 in. 760 /8 5/8 Q ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 1/2 ODF will receive 1/2 OD tubing. 1/4 Pointed Toward ottom ap Parallel to Outlet onnection NET 1 lb. 454 g SHIPPING 1-1/2 lbs. 680 g

27 Page 26 ULLETIN t TYPE SF & EF F Refrigerants 22, 14a, 404, 507 Extended Solder onnections TYPE SF 1/4 ODF onnection Removable P/N Top View DIMENSIONS ONNETIONS - Inches OUTLET FITTING SIZE 1/ / UL SIZES - Inches HRGES 22 14a OD x.00 Z & ZP Series 0.50 OD x OD x.00 TYPE EF 1/4 ODF onnection Top View 2.4 /8 ODF Insert P/N DIMENSIONS ONNETIONS - Inches OUTLET FITTING SIZE 1/ / UL SIZES - Inches HRGES 22 14a OD x.00 Z & ZP Series 0.50 OD x OD x

28 t TYPE S ULLETIN Page 27 F Refrigerants 22, 14a, 404, 507 ODF Solder onnections Splan Type S valve is a brass bar body, externally adjustable valve with ODF solder connections. The thermostatic element is replaceable, and the inlet connection has a permanent 12 mesh strainer. This valve is designed f both air conditioning and refrigeration applications. Outlet onnections 5/8 ODF, 7/8 ODF, 1- ODF Mating Distributs (See ulletin 20-10) 1112, 111, 1115, 1116, 1620, 1622, 1651(R), 165(R), 1655(R) F complete details of construction, see page 5. Type S SPEIFITIONS ELEMENT SIZE NO. 8, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Internal Q VLVE TYPE NOMINL PITY Tons of THERMOSTTI HRGES VILLE TUING LENGTH ONNETIONS - Inches W ODF Solder lue figures are standard and will be furnished unless otherwise specified. INLET Q Valves listed in this column NOT VILLE with MOP Type air conditioning charges. W ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 5/8 ODF will receive 5/8 OD tubing. OUTLET SV-2 SVE-2 2 SV- SVE- /8 1/2 5/8, 7/8 1- SV-4 SVE-4 4 SV-5 SVE-5 5 1/2 5/8, 7/8 1- SVE-8 8 SVE /8 7/8 1- SJ-2 SJE-2 2 /8 1/2 5/8, 7/8 1- SJ-2-1/2 SJE-2-1/2 2-1/2 SJ- SJE- 1/2 5/8, 7/8 1- SJE ft. 5/8 7/8 1- SJE m SS-2 SSE-2 2 /8 1/2 5/8, 7/8 1- SS- SSE- SS-4 SSE-4 4 1/2 5/8, 7/8 1- SSE-6 6 SSE-7 7 5/8 7/8 1- SP-2 SPE-2 2 /8 1/2 5/8, 7/8 1- SP- SPE- SP-4 SPE-4 4 1/2 5/8, 7/8 1- SPE-6 6 SPE-7 7 5/8 7/8 1- Refer to Recoended Thermostatic harges on page NET 2 lbs kg SHIPPING lbs. 1.6 kg DIMENSIONS ONNETIONS - Inches FITTING SIZE / / / / /4 ODF onnection Top View UL SIZES - Inches HRGES 22 14a OD x.50 Z & ZP Series 0.50 OD x OD x.50 X 0.75 OD x OD x 4.00 P Series 0.50 OD x.50 VG 0.75 OD x Diameter of Type X harge Diaphragm ase is.62

29 Page 28 ULLETIN t TYPE ES F Refrigerants 22, 14a, 404, 507 Extended ODF Solder onnections Splan Type ES valve is a brass bar body valve having the same physical size as the Type S valve except the Type ES features a balanced pt construction and extended ODF connections. The thermostatic element is replaceable, and the inlet connection has a permanent 12 mesh strainer. The balanced pt construction makes this valve ideally suited f refrigeration and air conditioning applications which operate over widely varying conditions. Outlet onnections 7/8 ODF, 1- ODF, 1-/8 ODF Mating Distributs (See ulletin 20-10) 1112, 111, 1115, 1116, 1117, 1126, 1128, 165(R), 1655(R), 1657(R) F complete details of construction, see page 5. Type ES SPEIFITIONS ELEMENT SIZE NO. 8, KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Q ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 5/8 ODF will receive 5/8 OD tubing. W pproved f bi-directional applications. E Minimum quantities may apply to non-standard connections. Not all connection combinations are available. * X charge not available. VLVE TYPE NOMINL PITY Tons of ESVE-8 W 8 THERMOSTTI HRGES VILLE *Refer to Recoended Thermostatic harges on page TUING LENGTH INLET ONNETIONS - Inches E Q Extended ODF Solder lue figures are standard and will be furnished unless otherwise specified. OUTLET 1/2 5/8 7/8 1- ESVE-11 W 11 1/2, 5/8 7/8 7/8, 1-1-/8 ESVE /8 7/8 7/8, 1-1-/8 ESVE /8 1-1-/8 ESJE-5 W 5 1/2 5/8 7/8 1- ESJE-7 W 7 1/2, 5/8 7/8 7/8, 1-1-/8 ESJE-9 9 5/8 7/8 7/8, 1-1-/8 ESJE ft. 7/8 1-1-/8 ESSE-6 W m 1/2 5/8 7/8 1- ESSE-7-1/2 W 7-1/2 1/2, 5/8 7/8 7/8, 1-1-/8 ESSE /8 7/8 7/8, 1-1-/8 ESSE-1 1 7/8 1-1-/8 ESPE-6 W 6 1/2 5/8 7/8 1- ESPE-7-1/2 W 7-1/2 1/2, 5/8 7/8 7/8, 1-1-/8 ESPE /8 7/8 7/8, 1-1-/8 ESPE-1 1 7/8 1-1-/8 EXTERNL EQULIZER 1/4 Pointed Toward ottom ap Parallel to Outlet onnection NET 2 lbs kg SHIPPING lbs. 1.6 kg DIMENSIONS ONNETIONS - Inches 1/4 ODF onnection FITTING SIZE 1/ / / / Top View 1.81 UL SIZES - Inches HRGES 22 14a OD x.50 Z & ZP Series 0.50 OD x OD x.50 P Series 0.50 OD x.50 VG 0.75 OD x

30 t TYPE O ULLETIN Page 29 F Refrigerants 22, 14a, 404, 410, 507 ODF Solder onnections Splan Type O valve is a brass bar body, externally adjustable valve with ODF solder connections. The thermostatic element is replaceable, and the inlet connection has a permanent 12 mesh strainer. This valve type features a balanced pt construction, and it is designed f both air conditioning and refrigeration applications. synthetic seating surface provides tight shut-off during system off periods. This valve type has two body styles: a small body which provides capacities up to 0 tons R-22 and 5 tons R-410, and a large body which extends capacities to 70 tons R-22 and 60 tons R-410. Outlet onnections 1- ODF, 1-/8 ODF, 1-5/8 ODF Mating Distributs (See ulletin 20-10) 1115, 1116, 1117, 1125, 1126, 1127, 1128, 114, 1655(R), 1657(R), 1659(R) F complete details of construction, see page 5. U.S. Patent No.,742,722 Type O SPEIFITIONS ELEMENT SIZE NO. 8, NO., NO. 85 (R-410), ND NO. 85- (R-410), KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 410 (Z) 507 (P) 402 (L) Q ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus 5/8 ODF will receive 5/8 OD tubing. W Optional bi-directional feature is available, please contact Splan Division of Parker f me infmation. * X charge not available. VLVE TYPE NOMINL PITY Tons of OVE-15 W 15 OVE-20 W 20 OVE-0 W 0 OVE OVE OVE OJE-9 9 OJE OJE OJE-2 2 OJE-2 2 OJE OSE-9 9 OSE OSE OSE-0 0 OSE-5 5 OSE OZE-20 W 20 OZE-25 W 25 OZE-5 W 5 OZE OZE OPE-9 9 OPE OPE OPE-0 0 OPE-5 5 OPE THERMOSTTI ELEMENT SIZE NO. 8 THERMOSTTI HRGES VILLE *Refer to Recoended Thermostatic harges on page TUING LENGTH 5 feet 1.5 m ONNETIONS - Inches Q ODF Solder lue figures are standard and will be furnished unless otherwise specified. INLET 7/8 OUTLET 1-1-/8 1-1-/8 1-5/8 8 7/8 1-1-/8 1-1-/8 1-5/8 8 7/8 1-1-/8 1-1-/8 1-5/ NET 2 lbs kg 4 lbs kg 2 lbs kg 4 lbs kg 2 lbs kg 4 lbs kg 7/8 1-2 lbs kg 1-1-/8 7/8 1-1-/8 1-1-/8 1-5/8 4 lbs kg 2 lbs kg 4 lbs kg SHIPPING lbs. 1.6 kg 5 lbs kg lbs. 1.6 kg 5 lbs kg lbs. 1.6 kg 5 lbs kg lbs. 1.6 kg 5 lbs kg lbs. 1.6 kg 5 lbs kg

31 Page 0 ULLETIN t TYPE O F Refrigerants 22, 14a, 404, 410, 507 ODF Solder onnections TYPE O with NUMER 8 and 85 ELEMENT 1/4 ODF onnection 1.40 Top View DIMENSIONS ONNETIONS - Inches STRIGHT THRU ODF SOLDER 7/ / UL SIZES - Inches HRGES 22 14a OD X OD X.50 Z & ZP Series 0.50 OD X OD X OD X.50 P Series 0.50 OD X.50 G 0.75 OD X OD X 2.00 TYPE O with NUMER and 85- ELEMENT 1/4 ODF onnection * 2.75 Top View DIMENSIONS ONNETIONS - Inches STRIGHT THRU ODF SOLDER / / UL SIZES - Inches HRGES 22 14a OD x OD x OD x OD x 4.00 Z & ZP Series 0.75 OD x OD x OD x 4.00 P Series 0.75 OD x 4.00 G 0.75 OD x OD X 2.00 *R Element.

32 t TYPE H ULLETIN Page 1 F Refrigerants 22, 14a, 404, 507 ODF Solder - Flange onnections Splan Type H valve is a brass bar body, externally adjustable valve available with either ODF solder FPT flange connections. The thermostatic element is replaceable, and the inlet connection has a permanent 16 mesh strainer. The FPT flange connection requires the Splan K-1178 adapter kit. This valve type provides the smallest capacity TEVs with flange connections, and it is designed f both air conditioning and refrigeration applications. Outlet onnections 7/8 ODF, 1- ODF, H flange type Mating Distributs (See ulletin 20-10) 1109, 1110, 1112, 111, 1115, 1116, 1124, 1192 (aluminum), 165(R), 1655(R) F complete details of construction, see page 5. Type H SPEIFITIONS ELEMENT SIZE NO., KNIFE EDGE JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) Internal Q VLVE TYPE W NOMINL PITY Tons of THERMOSTTI HRGES VILLE Refer to Recoended Thermostatic harges on page TUING LENGTH ONNETIONS - Inches E ODF Solder lue figures are standard and will be furnished unless otherwise specified. FLNGE RING SIZE OD x ID Inches R Q Valves listed in this column NOT VILLE with MOP Type air conditioning charges. W Standard onnection 1/4 SE Flare, 1/4 ODF Solder connection available on request. E ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus, 5/8 ODF will receive 5/8 OD tubing. R Kit K-1178 with two brass bushings is available f two purposes: 1) To allow the current Type H valve to replace obsolete Types T and H with x 0.75 flange rings by mating with the smaller flange ring bushings and/ distributs. 2) To allow the Type H to use 1/2 FPT connections Part number and 1/2 socket weld connections Part number Order the appropriate 1/2 connections and one K-1178 per valve. INLET OUTLET HV-5-1/2 HVE-5-1/2 5-1/2 HVE-7 7 5/8 7/8 7/8 1- HVE HVE HVE /8 7/8 1- HJ- HJE- HJ-4 HJE-4 4 HJ-5 HJE-5 5 5/8 7/8 7/8 1- HJE-8 8 HJE ft. 7/8 7/8 1- HS- HSE- 1.5 m HS-4 HSE-4 4 HSE-6-1/2 6-1/2 5/8 7/8 7/8 1- HSE-9 9 HSE /8 7/8 1- HP- HPE- HP-4 HPE-4 4 HPE-6-1/2 6-1/2 5/8 7/8 7/8 1- HPE-9 9 HPE /8 7/ x 1.00 NET 5 lbs kg SHIPPING 6 lbs kg DIMENSIONS ONNETIONS - Inches SOLDERING USHING 1/ / / UL SIZES - Inches HRGES 22 14a OD x OD x OD x 4.00 Z & ZP Series 0.75 OD x OD x 4.00 X 0.75 OD x OD x 4.00 P Series 0.75 OD x 4.00 VG 0.75 OD x Diameter of Type X harge Diaphragm ase is.62

33 Page 2 ULLETIN t TYPE M F Refrigerants 22, 14a, 404, 507 ODF Solder - Flange onnections Splan Type M valve is a cast bronze body, externally adjustable valve with either ODF solder FPT flange connections. The thermostatic element is replaceable, and the inlet connection has a permanent 12 mesh strainer. This valve type provides capacities greater than the Type H, and it is designed f both air conditioning and refrigeration applications. Flanges f the Type M valve are interchangeable with the Type V. Outlet onnections 1- ODF, 1-/8 ODF, 1-5/8 ODF, M/V flange Mating Distributs (See ulletin 20-10) 1115, 1116, 1117, 1119, 1121, 1125, 1126, 1127, 1128, 114, 119 (aluminum), 1655(R), 1657(R), 1659(R) F complete details of construction, see page 5. Type M SPEIFITIONS ELEMENT SIZE NO. 6, GSKET JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) VLVE TYPE Q NOMINL PITY Tons of MVE MVE MVE-4 4 THERMOSTTI HRGES VILLE Refer to Recoended Thermostatic harges on page lue figures are standard and will be furnished unless otherwise specified. TUING LENGTH W ONNETIONS - Inches E ODF Solder Flange INLET OUTLET Q Standard onnection 1/4 SE Flare. 1/4 ODF Solder connection available on request. W FPT connections also available on request; 1/2 FPT - Part Number , /4 FPT - Part Number , 1 FPT - Part Number E ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus, 7/8 ODF will receive 7/8 OD tubing. 5 ft. 1.5 m 7/8 1- MVE /8 1- MJE MJE /8 1- MJE / ft. MSE m MSE MSE /8 1- MSE-0 0 7/8 1- MPE MPE MPE /8 1- MPE-0 0 7/ /8 1-5/8.62 FLNGE RING SIZE OD x ID Inches 1.75 x 1.25 NET 8 lbs..6 kg SHIPPING 9 lbs kg DIMENSIONS ONNETIONS - Inches 2.81 SOLDERING USHING 7/ / / UL SIZES - Inches HRGES 22 14a OD x 6.00 Z & ZP Series 0.88 OD x OD x 6.00 X 0.88 OD x OD x 6.00 P Series 0.75 OD x 4.00 VG 0.75 OD x Diameter of Type X harge Diaphragm ase is 4.75

34 t TYPE V ULLETIN Page F Refrigerants 22, 14a, 404, 507 ODF Solder - Flange onnections Splan Type V valve is a cast bronze body, externally adjustable valve available with either ODF solder FPT flange connections. The thermostatic element is replaceable, and the inlet connection has a permanent 12 mesh strainer. This valve features a dual pt semi-balanced design, and it is designed f both air conditioning and refrigeration applications. synthetic seating surface provides tight shut-off during system off periods. This valve provides greater capacities than the Type M. Flanges f the Type V valve are interchangeable with the Type M. Outlet onnections 1-/8 ODF, 1-5/8 ODF, M/V flange Mating Distributs (See ulletin 20-10) 1117, 1119, 1121, 1125, 1126, 1127, 1128, 114, 119 (aluminum), 1657(R), 1659(R) F complete details of construction, see page 5. Type V SPEIFITIONS ELEMENT SIZE NO. 6, GSKET JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) 404 (S) 502 (R) 408 (R) 507 (P) 402 (L) VLVE TYPE Q NOMINL PITY Tons of VVE VVE VVE VJE-5 5 VJE VJE VSE-8 8 VSE VSE VPE-8 8 VPE VPE THERMOSTTI HRGES VILLE Refer to Recoended Thermostatic harges on page lue figures are standard and will be furnished unless otherwise specified. TUING LENGTH W ONNETIONS - Inches E ODF Solder Flange INLET OUTLET Q Standard onnection 1/4 SE Flare. 1/4 ODF Solder connection available on request. W FPT connections also available on request; 1/2 FPT - Part Number , /4 FPT - Part Number , 1 FPT - Part Number E ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus, 7/8 ODF will receive 7/8 OD tubing. 5 ft. 1.5 m 10 ft. m 1-1-/8 1-1-/8 1-5/8 FLNGE RING SIZE OD x ID Inches 1.75 x NET 9 lbs kg SHIPPING 10 lbs kg DIMENSIONS ONNETIONS - Inches SOLDERING USHING 7/ / / UL SIZES - Inches HRGES 22 14a OD x 6.00 Z & ZP Series 0.88 OD x OD x 6.00 X 0.88 OD x OD x 6.00 P Series 0.75 OD x 4.00 VG 0.75 OD x Diameter of Type X harge Diaphragm ase is 4.75

35 Page 4 ULLETIN t TYPE W F Refrigerants 22, 14a ODF Solder - Flange onnections Splan Type W valve is a cast bronze body, externally adjustable valve available with ODF solder flange connections. The thermostatic element is replaceable, and the inlet connection has a permanent 12 mesh strainer. This valve features a dual pt semi-balanced design, and it is designed primarily f large capacity chillers. synthetic seating surface provides tight shut-off during system off periods. This valve provides the largest capacities available f flange connection TEVs. Outlet onnections 1-/8 ODF, 1-5/8 ODF Mating Distributs (See ulletin 20-10) 1117, 1125, 1126, 1127, 1128, 114, 1657(R), 1659(R) F complete details of construction, see page 5. Type W SPEIFITIONS ELEMENT SIZE NO. 6 and 7, GSKET JOINT (Splan ode) 22 (V) 407 (N) 407 (V) 422D (V) 14a (J) 12 (F) 401 (X) 409 (F) VLVE TYPE Q NOMINL PITY Tons of THERMOSTTI HRGES VILLE ELEMENT SIZE NUMER WVE E 6 WVE G only 7 WJE E 6 WJE G only 7 lue figures are standard and will be furnished unless otherwise specified. TUING LENGTH ONNETIONS - Inches W ODF Solder Flange INLET OUTLET Q Standard onnection 1/4 SE Flare, 1/4 ODF Solder connection available on request. W ODF Solder indicates a female connection on the valve of proper diameter to receive copper tubing of cresponding OD size. Thus, 1- ODF will receive 1- OD tubing. E Refer to Recoended Thermostatic harges, page. R F 1-1/2 NPT connections, der flanges separately f M42 solenoid eg P/N 9-1. The customer must supply 5/8 diameter x 6 long bolts and 5/8 diameter nuts. 10 ft. m 1-1-/8 1-5/ /8 1-5/8 2- FLNGE RING SIZE OD x ID Inches R 2.75 x 2.19 NET 10 lbs kg SHIPPING 11 lbs kg.8 * D 2.50 E Diameter olt Holes D DIMENSIONS ONNETIONS - Inches FITTING SIZE D E F / / UL SIZES - Inches ELEMENT SIZE HRGES NUMER 22 14a 0.88 OD x 6.00 Z & ZP Series 0.88 OD x 6.00 X OD x 6.00 P Series 0.75 OD x 4.00 VG 0.75 OD x 4.00 G OD x F F *Diameter of Diaphragm ase is.62 f Small W and 4.75 f Large W