Series V-42 Hot Runner Manifold

Transcription

1 H O R U N N E R E H N O L O G Y Series V- Hot Runner Manifold 50 Stabilize your rocess atalog Document _EN-Rev0 EN 05/06

2 Series V- Hot Runner Manifold roduct ype V- manifold for open flow bore. Hot runner manifold of series V- which are characterised by the following dimensions: M hickness mm J Flow bore Ø max. Ø mm 5 he manifolds can be supplied in standard shapes (I, H, X, Y) and in any realizable customized shape. Ø0 he runners of standard manfiolds are mechanically balanced. omponents Melt flow components Manifold block including heaters, connections and thermocouple. Inlet bushing (including heater). ttached parts and accessories enter support Dowel hrust pad ±0.00 E ) De H7 De Major Dimensions Manifold cutout, right (above) 0 B Manifold cutout, left (below) 5 B J M Height center support 5 IB De Ø of contact inlet bushing Ø De Ø of cutout inlet bushing Ø0 E Height inlet bushing 5/5/ 65/85 IB De Ø of contact inlet bushing Ø De Ø of cutout inlet bushing Ø50 E Height inlet bushing 5/5/ 65/85 ) Hardened insert recommended; is not supplied with the hot runner system Errors and exceptions excepted _EN-REV0 / 6

3 R Series V- Inlet Bushings Inlet bushings which can be combined with hot runner manifolds of series V-: IB IB E à all length s heated à threaded into manifold 0 jib RD De H7 De if R.9 then RD=Jib+8 if R>.9 then RD=Jib+0 ype E De De R Jib Heater power (Watt) IB max IB max W IB max W IB max W IB max. 0 6 / 8 / 0 - IB max. 0 6 / 8 / 0 00W IB max. 0 6 / 8 / 0 00W IB max. 0 6 / 8 / 0 5W Errors and exceptions excepted _EN-REV0 / 6

4 Series V- ttached arts and ccessories ttached parts and accessories for hot runner manifolds of series V- MS0-5-0 enter Lcs support MS hrust ad hrust pad L Dowel à DIN7979: 6 m6 6 Ø6 Ø0 Ø Ø0 Ltp 5 ±0.0 Ø8 M6 H Errors and exceptions excepted _EN-REV0 / 6

5 Series V- Manifold ypes and Styles Manifolds in Standard Shape Manifolds in standard shape have been designed by implementing the standard cavity and runner layouts which are widely used in practice: I, H, X and Y. Shown on the right there are several examples for manifolds in standard shape based on the components of series V-. hey are designed and made according to the customer s specification. Using capital letters to describe the different manifold types does not only refer to the shape of the manifold but also to the runner layout inside the manifold. he number represents the number of nozzles attached to the manifold. Manifolds in ustomised Shape Manifolds in customised shape are designed and made according to the customer s specification by using components of the selected manifold series. I I, I, I... Y... X... H... Bridge Manifolds Bridge manifolds make it possible to combine several manifolds to one feed system. hey are are designed and made according to the customer s specification by using components of the selected manifold series Errors and exceptions excepted _EN-REV0 5 / 6

6 North merica Synventive Molding Solutions Inc. 0 entennial Drive eabody, M 0960 el.: Fax: info@synventive.com Europe Synventive Molding Solutions GmbH Heimrodstraße 0. O. Box 665 Bensheim el. :+9 (0) Fax :+9 (0) infohrde@synventive.com sia Synventive Molding Solutions (Suzhou) o. Ltd. B Gang ian Industrial Square Suzhou Industrial ark, hina 50 el.: Fax: infohrcn@synventive.com _EN-REV Synventive Molding Solutions D: K