whitedriveproducts SERIES Hydraulic Motor LIGHT DUTY

Transcription

1 whitedriveproducts SERIES LIGHT DUTY Hydraulic Motor 1(800) WG

2 WG (ll Series) For Light Duty pplications whitedriveproducts overview The White Drive Products tradition of providing motors that excel in demanding applications continues with the WG series. WG motors provide an exceptionally solid platform for any light-duty application where sideload may present a concern. The WG incorporates our Roller Stator design which reduces friction and extends motor life. With displacements ranging from cm 3 [ in 3 ] per revolution and a choice of mounting, shaft, and port options, this motor is made to satisfy a variety of applications. The WG is a perfect fit when you require improved performance and long motor life at an affordable price. features / benefits Needle Roller earing is in optimum location to allow load to be placed as close to the center line of bearing as possible. High Pressure una Shaft Seal offers superior seal life and performance and eliminates the need for a case drain. typical applications conveyors, carwashes, positioners, light to medium-duty wheel drives, sweepers, grain augers, spreaders, feed rollers, screw drives, brush drives and more SerieS descriptions 275/276 - Hydraulic Motor Standard 280/281 - Hydraulic Motor With Larger Dia. Shafts 277/278 - Hydraulic Motor Modified Port Locations Heavy-Duty Drive Link receives full flow lubrication to provide long life. Roller Stator Motor Design increases efficiency and life by using roller contact versus solid, sliding contact design. Rubber Energized Steel Face Seal does not extrude or melt under high pressure or high temperature. SpecificationS CODE Displacement cm 3 [in 3 /rev] Speed Flow Torque Pressure rpm lpm [gpm] Nm [lb-in] bar [psi] cont. inter. cont. inter. cont. inter. cont. inter. peak [2.5] [11] 71 [630] 100 [870] 138 [2000] 190 [2750] 207 [3000] [2.7] [11] 78 [685] 108 [955] 138 [2000] 190 [2750] 207 [3000] [3.6] [] 57 [15] 107 [950] 150 [1320] 138 [2000] 190 [2750] 207 [3000] [4.3] [] 57 [15] 7 [10] 176 [1560] 138 [2000] 190 [2750] 207 [3000] [5.4] [] 57 [15] 162 [1430] 224 [1985] 138 [2000] 190 [2750] 207 [3000] [6.1] [] 57 [15] 185 [1640] 257 [2275] 138 [2000] 190 [2750] 207 [3000] [7.9] [] 57 [15] 241 [2135] 334 [2960] 138 [2000] 190 [2750] 207 [3000] [9.8] [] 57 [15] 304 [2690] 421 [3730] 138 [2000] 190 [2750] 207 [3000] [.2] [] 57 [15] 379 [3350] 525 [4650] 138 [2000] 190 [2750] 207 [3000] [14.1] [15] 76 [20] 380 [3380] 529 [4680] 1 [1750] 165 [2400] 200 [2900] [19.7] [15] 76 [20] 458 [4050] 600 [5300] 103 [1500] 134 [1950] 169 [2450] [24.4] [15] 76 [20] 548 [4850] 758 [6710] 100 [1450] 135 [1960] 170 [2460] Performance data is typical. Performance of production units varies slightly from one motor to another. Running at intermittent ratings should not exceed 10% of every minute of operation. 1(800)

3 whitedriveproducts WG (ll Series) For Light Duty pplications displacement performance [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 41 cm 3 [2.5 in 3 ] / rev 2 [0.5] 42 [11] Width 8.1 [.317] mm [in] 13 [117] [6] [134] [136] [136] [134] [9] [2] [115] [259] [276] [293] [299] [300] [298] [291] [283] [276] [401] 4 48 [427] [453] [462] [464] [462] [454] [445] [437] 982 Intermittent Ratings - 10% of Operation 65 [577] [6] [625] [628] [626] [617] [607] [599] [852] [869] [874] [872] [861] [849] 671 Theoretical Torque - Nm [lb-in] 22 [198] 45 [396] 67 [595] 90 [793] 3 [1090] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 44 cm 3 [2.7 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 42 [11] 15 [131] 16 [140] 17 [148] 17 [151] 17 [150] 17 [147] 16 [140] 15 [131] 14 [1] 32 [285] 34 [303] 36 [322] 37 [328] 37 [329] 37 [326] 36 [318] 35 [308] 34 [298] 50 [438] 53 [467] 56 [496] 57 [506] 57 [508] 57 [505] 56 [496] 55 [485] 54 [475] 71 [631] 76 [669] 77 [683] 78 [687] 77 [685] 76 [674] 75 [662] 74 [652] 105 [930] 107 [950] 108 [955] 108 [953] 106 [942] 105 [928] Width Theoretical Torque - Nm [lb-in] 8.7 [.344] 24 [215] 49 [430] 73 [645] 97 [860] 134 [1182] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] Performance data is typical. Performance of production units varies slightly from one motor to another. 1(800)

4 WG (ll Series) For Light Duty pplications whitedriveproducts displacement performance [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 60 cm 3 [3.6 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 22 [191] 23 [203] 24 [213] 24 [214] 24 [211] 23 [205] 21 [190] 19 [170] 15 [136] 11 [98] 45 [400] 48 [425] 51 [450] 52 [458] 52 [458] 51 [453] 49 [437] 47 [417] 43 [384] 39 [349] 69 [608] 73 [648] 78 [687] 79 [702] 80 [704] 79 [700] 77 [685] 75 [664] 71 [632] 68 [599] 98 [870] 104 [924] 107 [945] 107 [950] 107 [948] 105 [932] 103 [9] 99 [879] 96 [850] 145 [80] 148 [1310] 149 [1320] 149 [1319] 147 [1304] 145 [82] 141 [51] Width Theoretical Torque - Nm [lb-in] 11.8 [.463] 33 [292] 65 [580] 98 [869] 131 [1159] 180 [1594] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 70 cm 3 [4.3 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 26 [231] 28 [244] 29 [255] 29 [256] 28 [251] 27 [243] 25 [222] 22 [196] 17 [149] 11 [96] 54 [474] 57 [504] 60 [534] 61 [542] 61 [541] 60 [535] 58 [514] 55 [488] 50 [443] 44 [393] 81 [718] 86 [765] 92 [8] 94 [829] 94 [831] 93 [827] 91 [807] 88 [781] 83 [736] 78 [690] 116 [1025] 3 [1090] 6 [1115] 7 [11] 6 [1119] 4 [1100] 1 [1073] 116 [1030] 111 [986] 170 [1507] 175 [1544] 176 [1557] 176 [1556] 174 [1539] 171 [15] 166 [1470] Width Theoretical Torque - Nm [lb-in] 13.8 [.542] 38 [338] 76 [667] 115 [1015] 153 [1354] 210 [1861] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] Performance data is typical. Performance of production units varies slightly from one motor to another. 1(800)

5 whitedriveproducts WG (ll Series) For Light Duty pplications displacement performance [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 88 cm 3 [5.4 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 34 [301] 36 [318] 37 [331] 37 [331] 37 [323] 35 [3] 32 [280] 27 [242] 20 [173] 11 [94] 69 [609] 73 [647] 77 [684] 78 [694] 78 [692] 77 [683] 74 [654] 70 [616] 62 [549] 53 [473] 104 [917] 110 [967] 117 [1036] 0 [1058] 0 [1061] 119 [1055] 116 [1028] 1 [990] 105 [925] 96 [853] 147 [1305] 157 [1388] 161 [1421] 162 [1430] 161 [1427] 158 [1402] 154 [1365] 147 [1301] 139 [32] 217 [1917] 222 [1966] 224 [1984] 224 [1984] 222 [1962] 218 [1926] 211 [1864] Width Theoretical Torque - Nm [lb-in] 17.3 [.682] 48 [426] 96 [852] 144 [78] 193 [1704] 265 [2343] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 100 cm 3 [6.1 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 40 [350] 42 [369] 43 [383] 43 [382] 42 [372] 40 [358] 36 [320] 31 [273] 21 [190] 10 [93] 79 [701] 84 [744] 89 [786] 90 [798] 90 [795] 89 [784] 85 [749] 79 [703] 70 [622] 60 [528] 119 [1052] 8 [10] 134 [1189] 137 [14] 138 [18] 137 [11] 133 [1178] 8 [1133] 119 [1053] 109 [964] 169 [1496] 180 [1592] 184 [1630] 185 [1641] 185 [1637] 182 [1607] 177 [1564] 168 [1485] 158 [1399] 248 [2196] 255 [2254] 257 [2275] 257 [2276] 254 [2251] 250 [2209] 241 [2133] Width Theoretical Torque - Nm [lb-in] 19.7 [.777] 55 [486] 110 [971] 165 [1457] 220 [1943] 302 [2671] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] Performance data is typical. Performance of production units varies slightly from one motor to another. 1(800)

6 WG (ll Series) For Light Duty pplications whitedriveproducts displacement performance [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 9 cm 3 [7.9 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 52 [463] 55 [487] 57 [505] 57 [502] 55 [488] 53 [413] 47 [413] 39 [347] 26 [228] 10 [89] 104 [917] 110 [972] 116 [1026] 118 [1041] 117 [1037] 115 [1021] 110 [972] 103 [908] 89 [792] 74 [657] 155 [1370] 165 [1458] 175 [1548] 179 [1580] 179 [1586] 178 [1576] 173 [1531] 166 [1469] 153 [1355] 138 [24] 220 [1943] 234 [2069] 240 [20] 241 [2134] 241 [2130] 239 [2091] 229 [2030] 217 [1919] 202 [1792] 322 [2851] 331 [2929] 334 [2958] 335 [2961] 331 [2929] 325 [2872] 3 [2764] Width Theoretical Torque - Nm [lb-in] 25.4 [1.002] 71 [626] 141 [52] 2 [1877] 283 [2503] 389 [3442] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 161 cm 3 [9.8 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 67 [590] 70 [620] 72 [641] 72 [636] 70 [617] 67 [590] 59 [518] 49 [429] 31 [271] 10 [85] 131 [1158] 139 [28] 146 [95] 148 [1313] 148 [1307] 145 [87] 138 [22] 8 [1137] 111 [982] 90 [800] 195 [1726] 207 [1836] 220 [1949] 225 [1991] 226 [1997] 224 [1984] 218 [1927] 208 [1845] 191 [1693] 171 [1516] 276 [2445] 294 [2604] 301 [2668] 304 [2687] 303 [2682] 297 [2631] 288 [2552] 272 [2404] 252 [2231] 405 [3585] 416 [3684] 421 [3722] 421 [3728] 417 [3688] 408 [3614] 392 [3471] Width Theoretical Torque - Nm [lb-in] 31.8 [1.252] 88 [783] 177 [1565] 265 [2348] 354 [3131] 486 [4305] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] Performance data is typical. Performance of production units varies slightly from one motor to another. 1(800)

7 whitedriveproducts WG (ll Series) For Light Duty pplications displacement performance [500] 69 [1000] 104 [1500] 138 [2000] 190 [2750] 200 cm 3 [.2 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 84 [742] 88 [778] 91 [804] 90 [796] 87 [772] 83 [736] 73 [643] 60 [528] 36 [322] 9 [80] 164 [1447] 173 [1534] 183 [1617] 185 [1639] 184 [1631] 181 [1605] 172 [1522] 159 [1411] 137 [10] 110 [973] 243 [2152] 259 [2289] 275 [2430] 280 [2482] 281 [2490] 280 [2474] 271 [2400] 259 [2295] 237 [2098] 211 [1865] 344 [3045] 367 [3244] 376 [3325] 378 [3349] 378 [3343] 371 [3279] 359 [3178] 337 [2985] 3 [2758] 504 [4464] 519 [4589] 524 [4638] 525 [4646] 519 [4597] 509 [4503] 488 [4317] Width Theoretical Torque - Nm [lb-in] 39.4 [1.552] 110 [971] 219 [1941] 329 [29] 439 [3882] 603 [5338] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] [500] 69 [1000] 104 [1500] 1 [1750] 138 [2000] 166 [2400] 231 cm 3 [14.1 in 3 ] / rev Intermittent Ratings - 10% of Operation 2 [0.5] 45 [] 57 [15] 76 [20] 98 [864] 102 [905] 106 [934] 104 [925] 101 [895] 96 [853] 84 [743] 69 [607] 41 [364] 9 [76] 62 [551] 190 [1678] 201 [1779] 2 [1875] 215 [1900] 214 [1890] 210 [1860] 199 [1761] 184 [1631] 157 [1393] 5 [1111] 181 [1600] 282 [2493] 300 [2652] 318 [2816] 325 [2876] 326 [2885] 324 [2866] 314 [2780] 300 [2655] 274 [2422] 242 [2145] 240 [24] 349 [3089] 371 [3286] 380 [3363] 382 [3382] 381 [3369] 372 [3289] 358 [3167] 332 [2936] 301 [2662] 398 [3526] 425 [3757] 435 [3851] 438 [3880] 438 [3872] 429 [3798] 416 [3679] 390 [3451] 359 [3180] 510 [4509] 523 [4631] 528 [4675] 529 [4677] 521 [46] 508 [4498] 483 [4274] 453 [4007] Width Theoretical Torque - Nm [lb-in] 45.5 [1.791] 7 [11] 253 [2242] 380 [3363] 443 [3924] 507 [4484] 608 [5381] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] Performance data is typical. Performance of production units varies slightly from one motor to another. 1(800)

8 WG (ll Series) For Light Duty pplications whitedriveproducts displacement performance [500] 69 [1000] 104 [1500] 134 [1950] 322 cm 3 [19.7 in 3 ] / rev Intermittent Ratings 10% of Operation 45 [] 57 [15] 76 [20] 145 [80] 149 [1319] 147 [1304] 142 [60] 135 [1199] 117 [1039] 95 [841] 55 [485] 7 [64] [2501] 298 [2635] 302 [2670] 300 [2654] 295 [2610] 279 [2468] 258 [2279] 218 [1931] 171 [1517] [692] 447 [3951] 456 [4036] 457 [4049] 454 [4021] 440 [3897] 420 [3717] 382 [3377] 336 [2970] 244 [2160] 580 [5136] 595 [5265] 599 [5303] 598 [5291] 586 [5184] 566 [50] 529 [4678] 483 [4277] Width Theoretical Torque - Nm [lb-in] 63.5 [2.501] 177 [1564] 354 [39] 530 [4693] 689 [6102] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] [500] 69 [1000] 104 [1500] 134 [1950] 404 cm 3 [24.4 in 3 ] / rev Intermittent Ratings 10% of Operation 171 [1513] 341 [3018] 2 [0.5] [] 4 57 [15] [20] 186 Width Theoretical Torque - Nm [lb-in] [1991] 450 [3982] 643 [5690] 868 [7681] [2.501] mm [in] Displacement tested at 54 C [9 F] with an oil viscosity of 46cSt [213 SUS] 210 [1858] 211 [1867] 207 [1832] 192 [1699] 188 [1664] 176 [1558] 144 [74] 1 [991] 85 [752] 11 [97] 353 [34] 373 [3301] 386 [3416] 377 [3336] 370 [3274] 365 [3230] 327 [2894] 293 [2593] 266 [2354] 180 [1593] 537 [4752] 548 [4850] 546 [4832] 531 [4699] 545 [4823] 534 [4726] 513 [4540] 476 [42] 433 [3832] 337 [2982] 687 [6080] 693 [6133] 732 [6478] 753 [6664] 758 [6708] 737 [6522] 719 [6363] 688 [6088] 643 [5690] Performance data is typical. Performance of production units varies slightly from one motor to another. 1(800)

9 whitedriveproducts WG (275/276 Series) housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 2-HOLE, SE MOUNT, LIGNED END PORTS 06 3/4-16 UNF 0 G 3/8 49 [1.91] 53 [2.09] 2.5 [.100] N 44 [1.73] 131 [5.14] Ø82.5 [3.249] Ø82.3 [3.242] Ø106.4 [4.19] 11 [.45] Ø13.6 [.537] Ø13.4 [.529] 2-HOLE, SE MOUNT, LIGNED PORTS 10 1/2-14 NPT 11 7/8-14 UNF 18 G 1/2 68 G 1/2 (TP) 49 [1.91] 53 [2.09] N 10, 11, [1.60] [1.42] 131 [5.14] Ø82.5 [3.249] Ø82.3 [3.242] Ø106.4 [4.19] Ø13.6 [.537] Ø13.4 [.529] 10, 11, [.100] [.278] 4-HOLE, SQURE MOUNT, LIGNED END PORTS F26 3/4-16 UNF G2 G 3/8 101 [3.99] N 83 [3.28] Max 2.5 [.100] 44 [1.73] 80 [3.14] Ø44.4 [1.749] Ø44.2 [1.742] Ø82 [3.25] F26 - (4) 3/8-16 UNC, Min. Depth 20 [.80] G2 - (4) M10 x 1.5, Min. Depth 20 [.80] 11 [.45] Dimension N is charted on page 11. (TP) - Taller Pilot Height. Refer to detailed drawing for dimensional differences. 1(800)

10 WG (275/276 Series) whitedriveproducts housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 4-HOLE, SQURE MOUNT, LIGNED PORTS F30 1/2-14 NPT F31 7/8-14 UNF F38 G 1/2 101 [3.99] N 83 [3.28] Max 2.5 [.100] 41 [1.60] 80 [3.14] Ø44.4 [1.749] Ø44.2 [1.742] Ø82 [3.25] (4) 3/8-16 UNC, Min. Depth 20 [.80] 4-HOLE, WHEEL MOUNT, LIGNED END PORTS W26 3/4-16 UNF W2 G 3/8 132 [4.85] 13.6 [.537] 13.4 [.529] 33.7 [1.325] O 44 [1.73] Ø60.3 [2.374] Ø60.2 [2.371] 45 Ø130.2 [5.5] 8 [.33] 37 [1.45] 19 [.73] 11 [.45] 4-HOLE, WHEEL MOUNT, LIGNED PORTS W30 1/2-14 NPT W31 7/8-14 UNF W38 G 1/2 132 [4.85] 13.6 [.537] 13.4 [.529] 33.7 [1.325] 18 [.70] O Ø60.3 [2.374] Ø60.2 [2.371] 45 Ø130.2 [5.5] 8 [.33] 37 [1.45] 19 [.73] Dimensions N & O are charted on page 11. 1(800)

11 whitedriveproducts WG (275/276 Series) technical information allowable Shaft load / bearing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table below. SE & SQURE MOUNTS mm 445 dan [1000 lb] 445 dan [1000 lb] length & weight chart Dimension N is the overall motor length from the rear of the motor to the mounting flange surface and is referenced on detailed housing drawings listed on pages If figuring dimension N and using an 68 housing, substract 4.5 [.178] from the dimension. N # Side Ports End Ports Weight mm [in] mm [in] kg [lb] 137 [5.39] 156 [6.16] 7.3 [15.9] 138 [5.43] 157 [6.19] 7.3 [16.0] 141 [5.55] 160 [6.31] 7.4 [16.3] 143 [5.63] 162 [6.38] 7.5 [16.4] 147 [5.79] 166 [6.52] 7.6 [16.8] 149 [5.87] 168 [6.62] 7.7 [17.0] 155 [6.10] 174 [6.84] 8.0 [17.5] 161 [6.34] 180 [7.09] 8.2 [18.0] 169 [6.65] 188 [7.39] 8.5 [18.7] 175 [6.89] 194 [7.63] 8.7 [19.2] 193 [7.60] 2 [8.34] 9.5 [20.8] 193 [7.60] 2 [8.34] 9.5 [20.8] lb WHEEL MOUNTS SHFT ERING 2 3 in dan Dimension O is the overall motor length from the rear of the motor to the mounting flange surface and is referenced on detailed housing drawings listed on page 10. O # Side Ports End Ports Weight mm [in] mm [in] kg [lb] 106 [4.17] 5 [4.93] 7.6 [16.7] 106 [4.17] 5 [4.95] 7.6 [16.8] 110 [4.33] 9 [5.07] 7.7 [17.0] 1 [4.41] 131 [5.15] 7.8 [17.2] 115 [4.53] 134 [5.29] 8.0 [17.5] 118 [4.65] 137 [5.39] 8.0 [17.7] 3 [4.84] 142 [5.61] 8.3 [18.2] 130 [5.] 149 [5.86] 8.5 [18.8] 137 [5.39] 156 [6.16] 8.9 [19.5] 144 [5.67] 163 [6.40] 9.1 [20.0] 162 [6.38] 181 [7.11] 9.8 [21.6] 162 [6.38] 181 [7.11] 9.8 [21.6] dan [1000 lb] mm The overall motor weights listed in both charts above are referencing the end ported options, which are the heavier of the two. 275 & 276 series motor weights can vary ±.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc dan [1000 lb] ERING LOD MULTIPLICTION FCTOR TLE SHFT RPM FCTOR RPM FCTOR ERING lb in dan 1(800)

12 WG (275/276 Series) whitedriveproducts ShaftS 10 1 Straight 15 1 Straight Extended 25mm Straight 89 25mm Straight Stepdown P P 6.4 [.251] 6.4 [.250] 26.0 [1.020] 24.6 [.970] 6 [.24] 40 [1.58] 8.0 [.314] 7.9 [.313] 30.9 [1.218] 29.7 [1.168] 6 [.24] P [1.110] 28.0 [1.101] 25.4 [1.000] 25.4 [.999] 27.8 [1.094] 27.6 [1.085] Ø25.0 [.985] Ø25.0 [.984] 5/16-18 UNC, Min. Depth 20 [.80] M8 x 1.25, Min. Depth 20 [.80] Torque: 655 Nm [5800 lb-in] 13 1 Tapered Torque: 678 Nm [6000 lb-in] 14 1 Tapered (SE Standard) P P 25 [1.00] 34 [1.34] 17 [.67] 4.8 [.189] 4.8 [.188] 19.6 [.770] 4 [.16] 18.3 [.720] 22 [.85] 6.4 [.251] 6.4 [.250] 19.1 [.750] 4 [.16] 18.3 [.720] 2.3 [.092] 25.4 [1.000] 25.4 [0.999] 2.7 [.105] 25.4 [1.000] 25.4 [0.999] 2 [.10] 1:8 Taper 2 [.09] 1:8 Taper Torque: 655 Nm [5800 lb-in] slotted hex nut is standard on this shaft. Torque: 655 Nm [5800 lb-in] slotted hex nut is standard on this shaft. mounting / Shaft length chart Dimension P is the overall distance from the motor mounting surface to the end of the shaft. dditional shaft length information, if necessary, is noted as P 2 and does not increase or decrease the listed M dimensions in this chart. The overall shaft lengths are already factored into the overall distance from the mounting surface to the end of the shaft. P # Square & Mounts mm [in] 45 [1.77] 49 [1.94] 56 [2.21] 61 [2.41] 64 [2.50] 51 [2.00] Wheel Mounts mm [in] 76 [2.99] 80 [3.16] 87 [3.43] 92 [3.63] 95 [3.77] 82 [3.22] P 2 mm [in] N/ 43 [1.70] N/ N/ N/ 45 [1.78] dd 4.5 [.178] to shaft dimension P when a 68 housing is used. 1(800)

13 whitedriveproducts WG (275/276 Series) ordering information CHOOSE SERIES DESIGNTION 3. SELECT MOUNT & PORT OPTION 275 Counterclockwise Rotation 276 Clockwise Rotation W26 W30 W31 W38 4-Hole, Wheel Mount, ligned End Ports, 3/4-16 UNF 2-Hole, Wheel Mount, ligned Ports, 1/2-14 NPT 2-Hole, Wheel Mount, ligned Ports, 7/8-14 UNF 2-Hole, Wheel Mount, ligned Ports, G 1/2 4. SELECT SHFT OPTION The 275 & 276 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION cm 3 /rev [2.5 in 3 /rev] 44 cm 3 /rev [2.7 in 3 /rev] 60 cm 3 /rev [3.6 in 3 /rev] 70 cm 3 /rev [4.3 in 3 /rev] 88 cm 3 /rev [5.4 in 3 /rev] 100 cm 3 /rev [6.1 in 3 /rev] SELECT MOUNT & PORT OPTION F26 F30 F31 F38 9 cm 3 /rev [7.9 in 3 /rev] 161 cm 3 /rev [9.8 in 3 /rev] 200 cm 3 /rev [.2 in 3 /rev] 231 cm 3 /rev [14.1 in 3 /rev] 322 cm 3 /rev [19.7 in 3 /rev] 404 cm 3 /rev [24.4 in 3 /rev] 2-Hole, SE Mount, ligned End Ports, 3/4-16 UNF 2-Hole, SE Mount, ligned Ports, 1/2-14 NPT 2-Hole, SE Mount, ligned Ports, 7/8-14 UNF 2-Hole, SE Mount, ligned Ports, G 1/2 2-Hole, SE Mount, ligned Ports, G 1/2 (TP) 4-Hole, Square Mount, ligned End Ports, 3/4-16 UNF 4-Hole, Square Mount, ligned Ports, 1/2-14 NPT 4-Hole, Square Mount, ligned Ports, 7/8-14 UNF 4-Hole, Square Mount, ligned Ports, G 1/ Straight 25mm Straight 1 Tapered lack lack, Unpainted Mounting Surface 1 Tapered (SE Standard) 1 Straight Extended 25mm Straight Stepdown The 15 extended shaft is designed for use with one of the speed sensor options listed in STEP SELECT PINT OPTION None SELECT VLVE CVITY / CRTRIDGE OPTION 7. SELECT N DD-ON OPTION C W X Y Z Standard Lock Nut Solid Hex Nut Speed Sensor, Dual, 4-Pin Male Weatherpack Connector Speed Sensor, Dual, 4-Pin M Male Connector Speed Sensor, Single, 3-Pin Male Weatherpack Connector Speed Sensor, Single, 4-Pin M Male Connector 8. SELECT MISCELLNEOUS OPTION (TP) - Tall pilot. The speed sensor option is not available on tall pilot or wheel mount housings. C None Freeturning 1(800)

14 WG (277/278 Series) whitedriveproducts housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 2-HOLE, SE MOUNT, LIGNED END PORTS 10 1/2-14 NPT 11 7/8-14 UNF 49 [1.91] 53 [2.09] N 48 [1.90] 131 [5.14] Ø82.5 [3.249] Ø82.3 [3.242] Ø106.4 [4.19] Ø13.6 [.537] Ø13.4 [.529] 2.5 [.100] 2-HOLE, SE MOUNT, LIGNED MNIFOLD PORTS 17 1/2 Drilled 49 [1.91] 53 [2.09] 48 [1.90] N 14 [.56] 131 [5.14] Ø82.5 [3.249] Ø82.3 [3.242] 63.5 [2.500] Ø106.4 [4.19] Ø13.6 [.537] Ø13.4 [.529] 2.5 [.100] 14 [.56] Dimension N and allowable sideload information is found on page 11. 1(800)

15 whitedriveproducts WG (277/278 Series) housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 4-HOLE, SQURE MOUNT, LIGNED PORTS F30 1/2-14 NPT F31 7/8-14 UNF 101 [3.99] N 83 [3.28] Max 2.5 [.100] 41 [1.60] 80 [3.14] Ø44.4 [1.749] Ø44.2 [1.742] Ø82 [3.25] (4) 3/8-16 UNC, Min. Depth 20 [.80] 4-HOLE, WHEEL MOUNT, LIGNED PORTS W30 1/2-14 NPT 132 [4.85] 13.6 [.537] 13.4 [.529] 33.7 [1.325] 19 [.75] O Ø60.3 [2.374] Ø60.2 [2.371] 45 Ø130.2 [5.5] 8 [.33] 37 [1.45] 19 [.73] Dimensions N & O and allowable sideload information is found on page (800)

16 WG (277/278 Series) whitedriveproducts ShaftS 10 1 Straight 15 1 Straight Extended 25mm Straight 89 25mm Straight Stepdown P P 6.4 [.251] 6.4 [.250] 26.0 [1.020] 24.6 [.970] 6 [.24] 40 [1.58] 8.0 [.314] 7.9 [.313] 30.9 [1.218] 29.7 [1.168] 6 [.24] P [1.110] 28.0 [1.101] 25.4 [1.000] 25.4 [.999] 27.8 [1.094] 27.6 [1.085] Ø25.0 [.985] Ø25.0 [.984] 5/16-18 UNC, Min. Depth 20 [.80] M8 x 1.25, Min. Depth 20 [.80] Torque: 655 Nm [5800 lb-in] 13 1 Tapered Torque: 678 Nm [6000 lb-in] 14 1 Tapered (SE Standard) P P 25 [1.00] 34 [1.34] 17 [.67] 4.8 [.189] 4.8 [.188] 19.6 [.770] 4 [.16] 18.3 [.720] 22 [.85] 6.4 [.251] 6.4 [.250] 19.1 [.750] 4 [.16] 18.3 [.720] 2.3 [.092] 25.4 [1.000] 25.4 [0.999] 2.7 [.105] 25.4 [1.000] 25.4 [0.999] 2 [.10] 1:8 Taper 2 [.09] 1:8 Taper Torque: 655 Nm [5800 lb-in] slotted hex nut is standard on this shaft. Torque: 655 Nm [5800 lb-in] slotted hex nut is standard on this shaft. mounting / Shaft length chart Dimension P is the overall distance from the motor mounting surface to the end of the shaft. dditional shaft length information, if necessary, is noted as P 2 and does not increase or decrease the listed M dimensions in this chart. The overall shaft lengths are already factored into the overall distance from the mounting surface to the end of the shaft. P # Square & Mounts mm [in] 45 [1.77] 49 [1.94] 56 [2.21] 61 [2.41] 64 [2.50] 51 [2.00] Wheel Mounts mm [in] 76 [2.99] 80 [3.16] 87 [3.43] 92 [3.63] 95 [3.77] 82 [3.22] P 2 mm [in] N/ 43 [1.70] N/ N/ N/ 45 [1.78] dd 4.5 [.178] to shaft dimension P when a 68 housing is used. 1(800)

17 whitedriveproducts WG (277/278 Series) ordering information CHOOSE SERIES DESIGNTION 4. SELECT SHFT OPTION 277 Counterclockwise Rotation 278 Clockwise Rotation Straight 25mm Straight 1 Tapered Tapered (SE Standard) 1 Straight Extended 25mm Straight Stepdown The 15 extended shaft is designed for use with one of the speed sensor options listed in STEP SELECT PINT OPTION The 277 & 278 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION cm 3 /rev [2.5 in 3 /rev] 44 cm 3 /rev [2.7 in 3 /rev] 60 cm 3 /rev [3.6 in 3 /rev] 70 cm 3 /rev [4.3 in 3 /rev] 88 cm 3 /rev [5.4 in 3 /rev] 100 cm 3 /rev [6.1 in 3 /rev] SELECT MOUNT & PORT OPTION F30 F31 W31 2-Hole, SE Mount, ligned Ports, 1/2-14 NPT 2-Hole, SE Mount, ligned Ports, 7/8-14 UNF 9 cm 3 /rev [7.9 in 3 /rev] 161 cm 3 /rev [9.8 in 3 /rev] 200 cm 3 /rev [.2 in 3 /rev] 231 cm 3 /rev [14.1 in 3 /rev] 322 cm 3 /rev [19.7 in 3 /rev] 404 cm 3 /rev [24.4 in 3 /rev] 2-Hole, SE Mount, ligned Manifold Ports, 1/2 Drilled 4-Hole, Square Mount, ligned Ports, 1/2-14 NPT 4-Hole, Square Mount, ligned Ports, 7/8-14 UNF 4-Hole, Wheel Mount, ligned Ports, 7/8-14 UNF lack lack, Unpainted Mounting Surface 6. SELECT VLVE CVITY / CRTRIDGE OPTION None 7. SELECT N DD-ON OPTION Standard Lock Nut C Solid Hex Nut W Speed Sensor, Dual, 4-Pin Male Weatherpack Connector X Speed Sensor, Dual, 4-Pin M Male Connector Y Speed Sensor, Single, 3-Pin Male Weatherpack Connector Z Speed Sensor, Single, 4-Pin M Male Connector 8. SELECT MISCELLNEOUS OPTION None C Freeturning The speed sensor option is not available on wheel mount housings. 1(800)

18 WG (280/281 Series) whitedriveproducts housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 2-HOLE, SE MOUNT, OFFSET MNIFOLD PORTS 63 G 1/2 49 [1.91] 55 [2.17] 48 [1.90] Q 20 [.79] 20 [.79] 18 [.71] 131 [5.14] Ø82.6 [3.250] Ø82.5 [3.246] 18 [.71] Ø106.4 [4.189] Ø13.6 [.537] Ø13.4 [.529] 8.0 [.315] 16 [.63] 20 [.79] 36 [1.42] 20 [.79] (4) M8 x 1.25, Min. Depth 13 [.51] 4-HOLE, MGNETO MOUNT, OFFSET MNIFOLD PORTS C3 G 1/ [2.17] 48 [1.90] 16 [.63] Q 20 [.79] 20 [.79] 18 [.71] 131 [5.14] Ø82.6 [3.250] Ø82.5 [3.246] 18 [.71] 36 [1.42] [4.189] 13.5 [.531] 8.0 [.315] 20 [.79] 20 [.79] (4) M8 x 1.25, Min. Depth 13 [.51] 4-HOLE, SE MOUNT, OFFSET MNIFOLD PORTS G3 G 1/2 57 [2.25] Q 13.5 [.531] 5 [.20] 32 [1.26] 16 [.63] Ø82.6 [3.250] Ø82.5 [3.246] 21 [.82] 21 [.82] 16 [.63] [4.189] [4.169] 8.0 [.315] 53 [2.09] 22 [.90] (2) M10 x 1.5, Min. Depth 13 [.51] Dimension Q is found on page 20. 1(800)

19 whitedriveproducts WG (280/281 Series) housings Dimensions shown are without paint. Paint thickness can be up to 0.13 [.005]. 2-HOLE, SE MOUNT, LIGNED PORTS 68 G 1/2 49 [1.91] 55 [2.17] R 131 [5.14] Ø82.6 [3.250] Ø82.5 [3.246] Ø106.4 [4.189] Ø13.6 [.537] Ø13.4 [.529] 8.0 [.315] 48 [1.89] 4-HOLE, MGNETO MOUNT, LIGNED PORTS C8 G 1/ [2.17] R 131 [5.14] Ø82.6 [3.250] Ø82.5 [3.246] [4.189] 13.5 [.531] 8.0 [.315] 48 [1.89] Dimension 20 is found on page 100. ShaftS 21 32mm Straight 10.0 [.394] 10.0 [.392] 45 [1.77] 6 [.24] 68 [2.69] 58 [2.28] 35.0 [1.378] 34.8 [1.370] Ø32.0 [1.261] Ø32.0 [1.260] Torque: 882 Nm [7804 lb-in] M8 x 1.25, Min. Depth 18 [.71] Ø 2.5 [.10] Snap Ring 1(800)

20 WG (280/281 Series) whitedriveproducts technical information allowable Shaft load / bearing curve The bearing curve represents allowable bearing loads based on ISO 281 bearing capacity for an L 10 life of 2,000 hours at 100 rpm. Radial loads for speeds other than 100 rpm may be calculated using the multiplication factor table on page 11. LL 280 & 281 SERIES MOUNTS mm dan [1000 lb] 4000 length & weight chart Dimension Q is the overall motor length from the rear of the motor to the mounting flange surface and is referenced on detailed housing drawings listed on page 18. Q # Length mm [in] 157 [6.18] 158 [6.22] 161 [6.34] 163 [6.42] 166 [6.54] 169 [6.65] 175 [6.89] 181 [7.13] 189 [7.44] 195 [7.68] 213 [8.39] 213 [8.39] 63 & C3 Weight kg [lb] 6.1 [13.4] 6.2 [13.6] 6.3 [13.9] 6.4 [14.1] 6.6 [14.5] 6.7 [14.7] 7.0 [15.4] 7.3 [16.1] 7.6 [16.7] 7.9 [17.4] 8.6 [18.9] 8.6 [18.9] G3 Weight kg [lb] 6.4 [14.1] 6.4 [14.1] 6.6 [14.5] 6.7 [14.7] 6.9 [15.2] 7.0 [15.4] 7.2 [15.8] 7.5 [16.5] 7.9 [17.4] 8.2 [18.0] 9.0 [19.8] 9.0 [19.8] dan [1000 lb] SHFT Dimension R is the overall motor length from the rear of the motor to the mounting flange surface and is referenced on detailed housing drawings listed on page 19. R # Length mm [in] 141 [5.55] 142 [5.59] 145 [5.71] 147 [5.79] 150 [5.91] 153 [6.02] 159 [6.26] 165 [6.50] 173 [6.81] 179 [7.05] 197 [7.76] 197 [7.76] Weight kg [lb] 5.6 [.3] 5.6 [.3] 5.8 [.8] 5.9 [13.0] 6.1 [13.4] 6.2 [13.6] 6.5 [14.3] 6.8 [15.0] 7.1 [15.6] 7.4 [16.3] 8.2 [18.0] 8.2 [18.0] 1000 ERING & 281 series motor weights can vary ±.5 kg [1 lb] depending on model configurations such as housing, shaft, endcover, options etc. lb in dan 1(800)

21 whitedriveproducts WG (280/281 Series) ordering information CHOOSE SERIES DESIGNTION 4. SELECT SHFT OPTION 280 Counterclockwise Rotation 281 Clockwise Rotation 21 32mm Straight 5. SELECT PINT OPTION lack lack, Unpainted Mounting Surface 6. SELECT VLVE CVITY / CRTRIDGE OPTION The 280 & 281 series are bi-directional. Reversing the inlet hose will reverse shaft rotation. For applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the port of the motor. 2. SELECT DISPLCEMENT OPTION cm 3 /rev [2.5 in 3 /rev] 44 cm 3 /rev [2.7 in 3 /rev] 60 cm 3 /rev [3.6 in 3 /rev] 70 cm 3 /rev [4.3 in 3 /rev] 88 cm 3 /rev [5.4 in 3 /rev] 100 cm 3 /rev [6.1 in 3 /rev] cm 3 /rev [7.9 in 3 /rev] 161 cm 3 /rev [9.8 in 3 /rev] 200 cm 3 /rev [.2 in 3 /rev] 231 cm 3 /rev [14.1 in 3 /rev] 322 cm 3 /rev [19.7 in 3 /rev] 404 cm 3 /rev [24.4 in 3 /rev] None 7. SELECT N DD-ON OPTION Standard 8. SELECT MISCELLNEOUS OPTION None C Freeturning 3. SELECT MOUNT & PORT OPTION C3 C8 G3 2-Hole, SE Mount, Offset Manifold Ports, G 1/2 2-Hole, SE Mount, ligned Ports, G 1/2 4-Hole, Magneto Mount, Offset Manifold Ports, G 1/2 4-Hole, Magneto Mount, ligned Ports, G 1/2 4-Hole, SE Mount, Offset Manifold Ports, G 1/2 1(800)

22 North merica White Drive Products, Inc. P.O. ox 17 Hopkinsville, KY. US Phone: Fax: Europe White Drive Products GmbH Mannsnetterstrasse 34 D Opfenbach, Germany Phone: Fax: sia White (China) Drive Products Co., Ltd. 1-8 Ning Zhen Gong Lu Zhenjiang, 2021, Jiangsu, China Phone: Fax: Delivering The Power To Get Work Done! whitedriveproducts 1(800)