6000 Series. Highlights C-5. Description With torque up to 15,000 in-lb and 40 gpm continuous, this motor is packed with power operates very smoothly.

Transcription

1 Highlights Features 9 displacements available Presents a multitude of options that make this motor very smart and flexible to apply Benefits Very tough motor for demanding applications Can be used in a multitude of industries Very easy/flexible to integrate in a system Applications Mobile equipment Snow Removal, mowing Spayer, trencher Wood products Description With torque up to,000 in-lb and 40 gpm continuous, this motor is packed with power operates very smoothly. Specifications Geroler Element Flow l/min [GPM] Speed RPM Pressure bar [PSI] Torque Nm [lb-in] 9 Displacements 0 [40] Continuous** 22 [60] Intermittent* 77 Cont.** 866 Inter.* 200 [00] Cont.** 0 [00] Inter.* 168 [14920] Cont.** 187 [1680] Inter.* ** Continuous (Cont.) Continuous rating, motor may be run continuously at these ratings. * Intermittent (Inter.) Intermittent operation, 10% of every minute. C- Mowing Snow Removal Sprayer Trencher EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--1

2 Specifications 6000 Series Motors Displ. cm 3 /r [in 3 /r] 19 [11.9] 2 [.0] 310 [19.0] 390 [23.9] 490 [.0] 62 [38.0] 7 [.0] 80 [49.0] 98 [60.0] Speed Continuous (RPM) Intermittent Flow Flow Continuous 0 [40] 0 [40] 0 [40] 0 [40] 0 [40] 0 [40] 0 [40] 0 [40] 0 [40] l/min [GPM] Intermittent 1 [] 210 [] 22 [60] 22 [60] 22[60] 22 [60] 22[60] 22[60] 22 [60] Torque* Continuous 7 [100] 7 [610] 9 [ 82] 1 [102] 14 [12800] 1480 [13100] 1378 [92] 82 [04] 168 [14920] Nm [lb-in] Intermittent 860 [20] 1100 [9740] [11990] 16 [14490] 188 [166] 8 [16800] 1699 [040] 18 [16377] 187 [1680] Pressure Continuous 20 [00] 20 [00] 20 [00] 20 [00] 20 [00] 1 [20] [2000] [2000] [2000] bar Intermittent 310 [00] 310 [00] 310 [00] 310 [00] 27 [4000] 221 [3200] 1 [20] 1 [20 [2000] [ PSI] Peak 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 240 [00] 20 [00] 1 [20 1 [22] Weight Standard or 24,9 [.0] 2,2 [.] 2,6 [6.] 26,3 [8.0] 27.0 [9.] 27,9 [.] 28.6 [63.0] 29 [64.0],4 [67.0] kg [lb] Wheel Mount Bearingless 20.2 [44.] 20.4 [.0] 20.9 [46.0] 21. [47.] 22.2 [49.0] 23.1 [1.0] 28.3 [2.] 28.8 [3.].2 [6.] Maximum Case Pressure: See case pressure seal limitation graph. *See shaft torque ratings for limitations.. Note: To assure best motor life, run motor for approximately one hour at % of rated pressure before application to full load. Be sure motor is filled with fluid prior to any load applications. Maximum Inlet Pressure: 310 bar [00 PSI] Do not exceed pressure rating (see chart above). Maximum Return Pressure: 310 bar [00 PSI] with case drain line installed. Do not exceed pressure rating (see chart above). bar [ PSI] : The true pressure difference between inlet port and outlet port Continuous Rating: Motor may be run continuously at these ratings Intermittent Operation: 10% of every minute Recommended Fluids: Premium quality, anti-wear type hydraulic oil with a viscosity of not less than SUS at operating temperature. Recommended System Operating Temp.: -34 C to 82 C [- F to 180 F] Peak Operation: 1% of every minute Recommended Filtration: per ISO Cleanliness Code, 4406: 20/18/13 C--2 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

3 Performance Data 19 cm 3 /r [11.9 in 3 /r] [0] [1000] [00] [2000] [20] [00] [00] [4000] [00] Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent Peak No Operation 2 cm 3 /r [.0 in 3 /r] Flow LPM [GPM] [.] 1,9 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] 1 [280] 9 [290] 38 [0] 77 [310] 4 [320] 232 [0] [240] 2 46 [190] [160] [] 697 [80] [6] [10] 7 7 [680] 7 37 [710] 80 [740] 8 3 [7] 8 2 [7] 80 7 [720] [0] [660] 7 39 [6] 7 [620] 692 [0] 7 [90] [00] 1 [00] [90] [10] [1600] [90] [1 ] 17 6 [] [00] [1480] [10] [1410] [2290] [2340] [3100] [2390] 2 72 [20] [2480] [24] [2460] [2440] 27 0 [2400] 2 26 [23] [20] [2320] [2280] [3200] 66 [3280] [33] [3340] 37 2 [30] 380 [33] [30 ] [32] 3 89 [3240] 69 [3210] 733 [31] [3880] [40] [4600] [200] [790] [4] [62] [6900] [4190] [66] [7320] [4210] [4240] [4220] [4200] 47 2 [4160] 4 [41] 46 6 [4100] [4060] [4810] 116 [4990] [90] 7 28 [100] [80] [60] 4 [40] 42 [00] [4960] [4920] 749 [] [810 ] [900] [9] 6 6 [940] [940] [920] 6 11 [880] [840] [790] 6 2 [6710] [6800] [6810] [6810 ] [6790] 480 [60] 27 [74] [20] Flow LPM [GPM] [.] 1,9 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] 1 [] [] 208 [0] [1000] [1000] [2000] [20] [00] [00] [4000] [00] [440] [460] 122 [480] 183 [0] 2 [420] 7 [380] 368 [3] 4 [290] 4 6 [200] 2 6 [860] 9 4 [9 00] [960] 110 [9] [960] [940] 6 [920] [8] [800] [7] [690] 80 2 [] [0] 2 1 [1940] [940] [2 00 0] [2060] [2080] [20] [20] 2 1 [2020] 2 3 [1980] [1920] [18] [1790] [10] [1720] [16] [2990] [60] 3 4 [30] [42 10] [3180] [3180] [3160] 297 [3] 8 [3100] [] 3 47 [2980] 3 37 [2940] 3 99 [2860] [2800] [2740] [3960] 4 21 [4080] [42] [4290] [4290] [4260] [4240] [41] 4 4 [4060] [4010] 8 [3960] 4 68 [3890] [3820] [4920] 17 [90] 7 42 [260] 9 9 [360] 60 7 [420] [440] [400] [380] 0 3 [290] [] 80 9 [1] 80 [] [4920] 712 [4890] 783 [40] 11 [680] [80] 0 81 [6390] [6480] [610 ] 7 27 [6490] [6480] 7 8 [6410] [60] [90] 0 40 [6080] [940] 6 6 [880] [9] 6 6 [66] 7 [7100] [7420] [7490] [780] [790] [780] [720] [7440] [710 0] [6690] 7 74 [7] 8 12 [8020] 90 3 [80] [8480] [8660] [8680] [86] [8640] [820] 96 6 [9020] [910 ] [940] [9740] [790] Torque [lb-in] 6 } Nm 2 Speed RPM C- EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--3

4 Performance Data [0] [1000] 310 cm 3 /r [19.0 in 3 /r] [00] [2000] [20] 1 [00] 20 [00] 240 [4000] 27 [00] 310 Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent Peak No Operation 390 cm 3 /r [23.9 in 3 /r] Flow LPM [GPM] [.] 1,9 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [] [1] [2440] [10] [2460] [40] [] [60] 6 96 [] [40] [10] [480] 290 [420] 339 [360] [0] [1180] 1 47 [12] 9 [1260] 143 [12] 192 [0] [1160] [11] [1100] [0] 4 [1020] [982] [260] 290 [26] 0 [2690] [2660] [26] [260] [210] [2440] [2400] [2180] 2 82 [1960] [3620] [3800] 4 42 [39] 0 87 [40] [4060] [4040] 232 [4020] 279 [3990] [3920] 4 37 [38] [3780] 42 4 [3420] 38 [32] 6 [4780] [] 38 [280] 9 81 [420] [] [] [440] [420] [3] [220] [] 80 6 [4660] 2 [40] 684 [690] 6 14 [60] [6480] 7 73 [67] 0 [6800] [6820] [6840] [6820] 7 8 [67] 4 [6660] [680] [60] 68 1 [7] 6 6 [66] 7 10 [] [7710] 8 64 [8040] [80] [8190] [82] [8220] 9 29 [81] [8100] [8020] [7440] [80] [7780] [8260] 9 17 [8740] 98 [9260] [9400] [920] [960] [920] [9440] 320 [93] 360 [9220] [90] [97] 1 46 [10490] [60] 126 [10840] [10900] 12 2 [10840] [9] [10990] 1240 [118 00] 13 [11990] 109 Flow LPM [GPM] [1] 3,8 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [0 ] 8 4 [780] [810 ] [800] 90 1 [7] 8 4 [680] [620] 232 [] 6 2 [] 60 9 [0] 348 [380] 387 [ 00] [100 0] [00] [2 00 0] [2 00] 1 [] 17 2 [10] [800] [1640 ] [16] 18 [1620] 18 1 [1600] [80] [20] [1460] [1420] [13] 346 [1320] [1] [32] 1 [32] 3 17 [30] [33] [3390] [3380] [3360] 380 [3280] [3210] 266 [3] 4 [10] [2880] [26] 0 47 [2460] 280 [40] 16 [49] 60 [80] 7 72 [1] [] [] [60] 22 [00] 6 2 [49] 299 [4840] 336 [4740] 37 [40] 469 [44] 0 62 [6440] 7 14 [6] [6740] 0 68 [6810] 7 [6820] [6840] [6780] 220 [67] 0 26 [6640] [60] [6460] [6440] [6360] [] [8160] [84] 9 6 [820] [860] [890] 9 17 [8] [8480] [8380] [82] [8] 9 9 [80] [7860] [3 00 0] 20 [9080] [9] [10 0] 11 [10190] 10 [102] [10280] [10240] [10200] [10] [10000] 11 1 [ 00] 240 [90] [112] [11620] 13 [11860] [11920] [11980] 2 [4 00 0] 27 [20] 13 [12880] 33 [40] [ 00] 310 [14490] 16 1 [14480] [7] 6 6 Torque [lb-in] Nm } Speed RPM C--4 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

5 490 cm 3 /r [.0 in 3 /r] Performance Data [0] [1000] [00] [2000] [20] 1 [00] 20 [00] 240 [4000] 27 Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent [0] Peak No Operation [1000] 62 cm 3 /r [38.0 in 3 /r] [00] [2000] [20] 1 [00] 20 [3200] 221 Flow LPM [GPM] [1] 3,8 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [1010] 1 7 [0] 2 7 [4260] 480 [1020] 1 [10] 1 [1020] 1 60 [1000] 1 [110] [900] [8] [740] 8 2 [690] 80 2 [6] 7 2 [] 6 7 [2110] [2100] 2 [2090] 2 60 [2080] 2 [2060] [1980] 22 2 [19] [1840] [1710] [60] [0] [1] [42] [4280] [4290] 48 9 [4290] [4260] 480 [4180] 4 0 [40] [40] [39] [3860] [37] 42 3 [3240] 379 [2860] 32 4 [40] 69 3 [6280] [6410 ] [6490] 7 7 [60] 7 87 [6480] [6420] [6390] [6290] [90] [6080] [9] [220] [4860] 442 [80] 9 11 [80] [8620] 97 4 [86] [86] [8620] [880] 9 1 [80] [8420] [8340] [8] [20] [7] 80 4 [10420] [90] [10740] 12 1 [10800] [10820] [10820] [107] [10720] [60] 226 [10420] [10180] [40] 13 3 [] [12800] 14 [12890] 71 [12900] [180] [149] [166] Flow LPM [GPM] [1] 3,8 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [0] [1090] [11] [119] 1 [0] 1 72 [1] [0] [9] 144 [8] [7] [] [380] 241 [220] 2 [20] [20] [2600] 29 [2600] [246] [22] [196] [1790] [ ] 10 4 [4720] [] [390] 0 71 [340] [28] [180] 8 [80] 7 16 [4960] [4780] [4600] [4180] [3800] 4 3 [6690] [720] 8 21 [819] [81] [8] 9 89 [8080] 9 1 [7990] [79] [777] [78] [739] [698] [6600] 7 3 [9360] 0 6 [9410] 16 [11220] [117] [11740] [1172] [11] [11640] 13 6 [] [] [13100] 1480 [100] [100] [800] [0] [16800] 8 [2860] 32 4 Torque [lb-in] Nm } Speed RPM C- EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--

6 7 cm 3 /r [.0 in 3 /r] Performance Data [0] [7] [1000] [12] 8 [00] [17] [2000] [22] [20] 1 Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent Peak No Operation 80 cm 3 /r [49.0 in 3 /r] Fl ow LPM [GPM] [1] 3,8 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [1311] [277] [4200] [1340] 1 10 [123] [1290] [1277] 144 [1196] [1092] [6] 123 [1083] [9] [726] [] [286] 323 [284] [4363] [2889] [40] [2821] [] [273] [2794] [26] [2338] [2110] [18] [2227] [] [28] 12 9 [4478] 6 79 [4320] [4162] 4 [4040] [379] [17] [32] [3869] [480] 9 3 [00] 7 2 [809] [813] [80] [48] [6021] [871] [666] [7] 7 9 [223] [496] 201 [4148] [486] 49 3 [71] [868] [8714] [7272] [73] 8 37 [779] [78] [97] 8 97 [764] [7] [7122] 80 9 [683] [6672] [8] 6 2 [6604] [9202] [9338] 6 [93] 9 [9311] 2 96 [9289] [9022] [8828] [101 82] 10 6 [101] [92] [12419] 3 2 [66] [10877] [10984] [10907] [11] 127 [137] 13 [129] [13713] [040] Fl ow LPM [GPM] [1] 3,8 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [47] [99] 181 [99] [43] [17] [12] [3] [107] 0 [823] [92] [0] [3473] 392 [3469] [339] [3312] [7] [292] [7] [292] 98 [88] [47] 131 [4884] [4663] [1000] [39] [93] [32] 794 [6968] [12] 8 [8714] [8934] [9024] 1020 [1007] 1138 [29] 1 31 [8] [8983] [8943] [8812] [8681] [839] [8118] 7 16 [7832] [03] 89 2 [7407] [00] [] [3100] [4680] [6031] [7799] [1483] [3173] [] [6432] [810] [9633] [3331] 3 19 [3183] [] [2907] [2692] [2477] [27] [4426] [4214] [3806] [6744] 2 17 [6811] [6713] [646] [6320] [608] [849] [9] [40] 2 68 [83] [10411] 11 [10411] [10060] [17] [11319] 1279 [112] [11842] [12283] 1388 [10] [46] [2000] [27] 13 [1239] [04] [13726] 1 [22] [164] [441] [20] 1 [16377] [6604] Torque [lb-in] Nm } Speed RPM C--6 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

7 Performance Data [0] [7] 98 cm 3 /r [60.0 in 3 /r] D Pressure Bar [PSI] [1000] [12] 8 [00] [17] [2000] Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent Peak No Operation Flow LPM [GPM] [1] 3,8 7, [8] [12] [16] [20] [24] [28] [32] [36] [40] 1 [] [60] 227 [0] 2 3 [20] 2 [2020] 2 [2010] 22 [10] 2 77 [1810] [1620] [1480] [1] [8] 9 3 [4110] 46 3 [10] [4 ] [1980] [4290] [4400] 49 [4390] 49 [4320] 490 [4220] [4060] [3920] [3740] [3490] [3240] 3 [2960] 32 1 [7] 6 2 [62] [6480] 77 [66] 7 [66] 7 [660] 740 [6480] 7 [62] 92 [80] [980] [710] [420] 0 2 [160] [4660] 2 2 [40] 86 2 [80] [840] [8790] [8860] [8790] [8720] 98 [80] 960 [8420] 9 [8200] 92 [79] [40] 86 1 [] 8 [7160] [9] [10420] [] 14 [10940] [10] [11000] 12 9 [109] 12 7 [10790] [] 0 [10280] 1160 [9940] [990] [9310] [90] [] 1410 [12800] [190] [13240] [13260] 00 8 [13160] [12990] [12820] [13860] 6 4 [13900] 13 [100] [040] [14920] [8] [1680] [7160] Torque [lb-in] 810 } Nm 229 Speed RPM C- EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--7

8 Dimensions Standard Mount Standard Mount Ports 1 /16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 1 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) or 1 /16 UN-2B SAE O-ring Staggered Ports (2) with Shuttle 9/16-20 UNF-2B SAE O-ring Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Y X Port B Case Drain Port Standard SAE CC Flange 24,6/24,1 [.97/.9] 13,9/12,8 [./.] 14,3/14,14 [.72/.7] Dia. Thru (4) 127,00/126,87 [.000/4.99] DIa. 114, [4.8] Square 146,8 [.78] Square 1,9 [6.37] Dia. Bolt Circle Standard Motor Mount Dimensions Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 19 [11.9] 187, [ 7.38] 2,0 [10.63] 2 [.0] 193,0 [ 7.60] 27,6 [10.8] 310 [19.0] 200,4 [ 7.89] 283,0 [11.14] 390 [23.9] 209,0 [ 8.23] 2,6 [11.48] 490 [.0] 220,2 [ 8.67] 2,8 [11.92] 62 [38.0] 2,0 [ 9.2] 317, [12.] 98 [60.0] 274,6 [10.81] 7,1 [14.06] 147,4 [.80] C--8 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

9 Dimensions Wheel Mount Wheel Mount Ports 1 /16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 1 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) or 1 /16 UN-2B SAE O-ring Staggered Ports (2) with Shuttle 9/16-20 UNF-2B SAE O-ring Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Port B Y X Case Drain Port 98,6/97,0 [3.88/3.82] 139,/139,7 [.0/.49] Dia. 166,4 [6.] Square 127,00/126,87 [.000/4.99] Dia. 1,21 [.126] C- 22,6/22,1 [.89/.87] 7,74 [.] Min. 17,3/16,8 [.68/.66] 14,3/14,14 [.72/.7] Thru (4) 184,12 [7.2] Dia. Bolt Circle Wheel Mount Motor dimensions Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 19 [11.9] 102,6 [4.04] 18,2 [7.29] 2 [.0] 108,2 [4.26] 190,8 [7.1] 310 [19.0] 1,6 [4.] 198,1 [7.80] 390 [23.9] 124, [4.90] 207,1 [8.] 490 [.0] 1,4 [.33] 217,9 [8.8] 62 [38.0] 0,1 [.] 232,7 [9.16] 98 [60.0],7 [7.47] 272, [10.73] EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--9

10 Dimensions Global Mount (ISO) Global Mount (ISO) Ports 1 /16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 1 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) or 1 /16 UN-2B SAE O-ring Staggered Ports (2) with Shuttle 9/16-20 UNF-2B SAE O-ring Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Y Port B X 20,3/19,8 [.80/.78] 38,7/37,7 [1.2/1.48] 179,6 [7.07] 9,99/9,94 [6.299/6.297] Pilot Dia. 179,6 [7.07] 141,43 [.68] (4) Case Drain Port mm Dia. Straight Shaft 18,21/17,83 [.717/.2] Dia. Thru (4) 200,00 [7.874] Dia. Bolt Circle 124,/,4 [4.90/4.74],26/69,7 [2.6/2.746] 8,4/4,6 [.33/.18] 3,49/2, [2./2.07] 14,000/13,97 [.12/.49] 8,992/8,890 [.40/.00] 79,2 [3.12] Coupling Length,000/49,974 [1.968/1.967] M12 x 1,7 2,0 [.98] Min. Depth Global Mount Motor Dimensions Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 310 [19.0] 182,4 [ 7.18] 264,9 [10.43] 390 [24.0] 1,0 [ 7.2] 273,6 [10.77] 490 [.0] 202,2 [ 7.96] 284,7 [11.21] 62 [38.0] 216,9 [ 8.4] 299, [11.79] 800 [.0] 229,4 [ 9.03] 312,2 [12.29] 800 [49.0] 236,7 [ 9.32] 319,3 [12.7] 98 [60.0] 26, [10.10] 339,1 [13.] C--10 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

11 Dimensions Bearlingless Bearingless Ports 1 /16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 1 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) or 1 /16 UN-2B SAE O-ring Staggered Ports (2) with Shuttle 9/16-20 UNF-2B SAE O-ring Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Y Port B X 127,00/126,87 [.000/4.99] Dia. 114, [4.8] Square 1,9 [6.37] Dia. Bolt Circle 14./14,14 [.72/.7] Case Drain Port Face Seal or O-ring Seal 24,2/21,0 [.9/.83] 12,7/12,1 [./.48] 147,6 [.81] Square Note: Similar to SAE C Type Mounting Flange º Case Flow Holes (2) For 6000 bearingless motor application information, contact your Eaton representative (mating C coupling blanks available from Eaton Hydraulics). Note: After machining blank, part must be hardened per Eaton specification. F C E D F E D C- Bearingless Motor Dimensions Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 19 [11.9],4 [4.] 188,0 [7.40] 2 [.0] 111,0 [4.37] 193, [7.62] 310 [19.0] 118,4 [4.66] 200,9 [7.] 390 [23.9] 127,3 [.01] 209,6 [8.2] 490 [.0] 138,2 [.44] 220,7 [8.69] 62 [38.0] 2,9 [6.02] 2, [9.27] 98 [60.0] 192,8 [7.9] 27,1 [10.83] C 47,2 [1.86] Dia. D 111, [4.39] E,4 [4.19] Full Form Dia. F 6,9 [.27] Min. Full Form Dia. G 10,2 [.40] Min. H 86,1 [3.39] J 66, [2.62] Dia. Mating Coupling Blank Eaton Part No J G H EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--11

12 Installation Information Bearingless 1 Internal spline in mating part to be as follows: Material to be ASTM A4, 8620H. Carbonize to a hardness of HRc with case depth (to HRc) of 0,0-1,02 [ ] (dimensions apply after heat treat). 2 Mating part to have critical dimensions as shown. Oil holes must be provided and open for proper oil circulation. 3 Seal to be furnished with motor for proper oil circulation thru splines. 4 Some means of maintaining clearance between shaft and mounting flange must be provided. Similar to SAE C Four Bolt Flange.. 6 Counterbore designed to adapt to a standard sleeve bearing,010 -,038 [ ] ID by 60,01-60,079 [ ] O.D. (Oilite bronze sleeve bearing) ,2/12,7 [.6/.] 1,/0, [.06/.02] -D- 49,848/49, /1.96 0,13[.00] A 40,1/39,6 [1.8/1.6] Dia. 2,37 [2.062] Dia. M 3 1,8/0, [.07/.02] Case Flow -A- R 1,8/1,2 [.07/.0] 24,6/24,1 [.97/.9] 1,/0,8 [.06/.03] 81,8/80,7 [3.22/3.18],1/4,6 [.20/.18] D (2) Thru Oil Hole 6,8/6,4 [.27/.2] 6 0,13 [.00] A Case Flow R 0, [.02] 4 Major -B- 9,4/8,4 [.37/.33] 69,3/68,1 [2.73/.2.68] Coupling Depth Circular Tip R. Minor Finish Fillet R. Pitch Form Finish Spline Pitch...8./17 Pressure Angle... Number of teeth Class of Fit... Ref. Type of Fit... Side Pitch Diameter...Ref.,88823 [ ] 0,20 [.008] D Base Diameter... Ref. 31,0462 [ ] Major Diameter...39,17 [1.42] 38,97 [1.34] Min.. Min. Minor Diameter... 33, - 33,48 [ ] Form Diameter, Min...38,33 [1.9] Fillet Radius... 0,64-0, [ ] Tip Radius... 0,2-0,1 [ ] Finish...1,6 (63) Involute Profile Variation...+0,000-0,02 [ ] Total Index Variation...0,038 [.00] Lead Variation...0,013 [.000] Circular Space Width: Maximum Actual...,898 [.2322] Minimum Effective...,804 [.228] Maximum Effective...Ref.,87 [.26] Minimum Actual...Ref.,834 [.2297] Dimension Between Two Pins... Ref. 26,929-27,084 [ ] Pin Diameter...6,223 [.20] Pins to Have 4,0 [.160]. Wide Flat for Root Clearance C--12 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

13 Dimensions Shafts Splined 1 1/2 Inch Straight 1328 [117] Torque Nm [lb-in] 9,6/9,2 [.3/.37] 78,2/,2 [3.08/3.00] End of Shaft to Mounting Surface (Std) 42,0/40,6 [1.6/1.60] 1 3/4 Inch Tapered 2107 [186] Torque Nm [lb-in] 1-1/4-18 UNEF-2A 4,1 [.16] Dia. Thru 177,8/17,0 [7.00/6.89] End of Shaft to Mounting Surface (Whl) 31,7 [1.2] 3/8-16 UNC x 18, [.73] Deep 42,40/42,13 [1.669/1.69] 38,10/38,04 [1.0/1.498] Dia. 6,7 [2.23] Coupling 44. [1.7] Dia. 77,0 [3.03] SAE J1 Standard Tapered Shaf t 12,00 0,17 Taper per Mete r [1.0±.002 Taper per Foot],4/,20 [.218/.20] 11,138/11,112 [.438/.437] 1 1/2 Inch 17 Tooth Splined Tapered Shaft Hub Data 1328 [117] Torque Nm [lb-in] 3/8-16 UNC x 18, [.73] Deep 40,3 [1.9] Min. Full Spline 78,2/,2 [3.08/3.00] End of Shaft to Mounting Surface (Std) Recommended Torque : (6 Nm [47 lb-ft] Dry) (10 Nm [37 lb-ft] Lub) Plus Torque required t o align the slotted nut with the Shaft Crosshole. Hub External Involute Spline, DP 17 Tooth P.A. Flat Root Side Fit per ANSI B92.1, 19 38,10 [1.0] Dia. Ref. 6,7 [2.23] Coupling 60,17/7,78 [2.369/2.27] C- 40 mm Straight 1328 [117] Torque Nm [lb-in] 8,000/7,0 [.3149/.31] 12,000/11,97 [.4724/.48] 94,0/,9 [3./3.62] End of Shaft to Mounting Surface (Std) 9,2/4, [.36/.18] 63,7/62,2 [2.1/2.] Slotted Hexagon Nut,4 [2.18] 4,1 [.16] 11,2 [.44] 1-1/4-18 UNEF-2B 43,03/42,72 [1.694/1.682] M12 x 1,7-6H 2 mm [.984] Deep 40,018/39,992 [1.7/1.7] 7,6 [2.98] Coupling º º,7 [.62] EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--13

14 Shaft Side Load Capacity These curves indicate the radial load capacity on the motor shaft(s) at various locations with an external thrust load of 4 kg [1000 lb]. The maximum allowable thrust load is 908 kg [2000 lb]. Note: Case pressure will increase the allowable inward thrust load and decrease the allowable outward thrust load. Case pressure will push outward on the shaft at 109 kg/7 Bar [241 lb/100 PSI]. Each curve is based on Thrust Load Standard Motor Straight and Splined Shafts [lb] [10000] [ 8000] [ 6000] [ 4000] [ 2000] [lb] 0 mm [inch] kg Wheel Motor Tapered Shaft kg [-4] [-3] [-2] [-1] 0 [1] [3] Mounting Surface Axial Loads 908 kg [2000 lb] B 10 bearing life (2000 hours of 12,000,000 shaft revolutions at 100 RPM) at rated output torque. To determine radial load at speeds other than 100 RPM, multiply the load values given on the bearing curve by the factors in the chart below. [10000] [ 8000] [ 6000] [ 4000] [ 2000] mm -20 [inch] [-1] [1] [3] Mounting Surface [] [6] [7] [8] RPM Multiplication Factor For 3,000,000 shaft revolutions or 0 hours Increase these shaft loads 2%. C--14 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

15 Case Pressure and Case Port Char-Lynn 6000 Series motors are durable and have long life as long as the recommended case pressure is not exceeded. Allowable case pressure is highest at low shaft speeds. Consequently, motor life will be shortened if case pressure exceeds these ratings (acceptability may vary with application). Determine if an external case drain is required from the case pressure seal limitation chart. 100 Case Pressure Bar [PSI] 0 0 [1000] [ 0] 0 Case Pressure Seal Limitation Case Drain Intermittent -- Required Case Drain Optional Continuous -- Case Drain Optional Speed RPM Case Porting Advantage Contamination Control flushing the motor case. Cooler Motor exiting oil draws motor heat away. Extend Motor Seal Life maintain low case pressure with a preset restriction in the case drain line. C- EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--

16 Dimensions Ports 1 /16-12 O-ring Ports (2) or G 1 (BSP) Ports (2) Port B 7/16-20 UNF O-ring or G 1/4 (BSP) Port Case Drain 4 Bolt 3/4 Inch Split Flange Ports to Fit SAE J18c (2) Except for 20,0 [.79] Min. Thd. Dp. Port B 7/16-20 UNF O-ring Port Case Drain Port A Port A 19,4/18,7 [./.7] 17 13,8/10,6 [.4/.42],9/34,7 [1.414/1.366] 19,4/18,7 [./.7] 8,0/6,3 [2.28/2.22] 77,7 [3.06] 23,9 [.94] 47,63 [1.87] 20,7/17,4 [.80/.] 11,2 [.44] 22,23 [.87] 13,8/10,6 [.4/.42] 4,9 [2.16] 77,0 [3.03] Port B 9/16-18 UNF O-ring 6,8 [2.9] 44,2/39,6 [1.74/1.6] 1 /16-12 O-ring Ports (2) with Shuttle Port B 9/16-18 UNF O-ring 6,8 [2.9] 81,8 [3.22] Port A 19,4/18,7 4,4/3,0 [.17/.12],9/34,7 [1.414/1.366] 79, [3.13] Port A 19,4/18,7 [./.7] 17 4,4/3,0 [.17/.12] 19,4/18,7 [./.7],9/34,7 [1.414/1.366] 79, [3.13] 8,0/6,3 [2.28/2.22] 66,0 [2.60] 20,1 [.79] 6,8 [2.9] 93,7 [3.69] C--16 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011

17 Product Numbers Note: For 6000 Series Motors with a configuration Not Shown in the charts above: Use model code number system on the next page to specify product in detail. Use digit prefix 112-, 113-, or plus four digit number from charts for complete product number Example Orders will not be accepted without three digit prefix. Mounting Shaft Port Size Displ. cm 3 / r [in 3 / r] / Product Number * 80* 98 [11.9] [.0] [19.0] [23.9] [.0] [38.0] [.0] [49.0] [60.0] 1 1/2 inch Straight 1 /16 O-ring Standard Wheel Motor Bearingless *New release 40 mm Straight G 1 (BSP) /2 Inch 17 T Splined 1 /16 O-ring G 1 (BSP) mm Straight G 1 (BSP) /4 Inch Tapered 1 /16 O-ring /16 O-ring G 1 (BSP) Mounting Type - Standard (Code H), 4 Bolt: 160,0 [6.] Pilot Dia. 18,01 [.9] Dia. Mounting Holes 200,0 [7.87] Dia. Bolt Circle Output Shaft - Straight (Code 21) Ports - G1 (BSP) Staggered G 1/4 Case Drain (Code C) Paint - Low Gloss Black (Code A) Use digit prefix 112- plus four digit number from charts for complete product number Example Orders will not be accepted without three digit prefix. Mounting Shaft Port Size Displ. cm 3 / r [in 3 / r] / Product Number [19.0] [23.9] [.0] [38.0] [.0] [49.0] [60.0] Standard mm Straight G 1 (BSP) C EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011 C--17

18 Model Code The following -digit coding system has been developed to identify all of the configuration options for the 6000 Series motor. Use this model code to specify a motor with the desired features. All -digits of the code must be present when ordering. You may want to photocopy the matrix below to ensure that each number is entered in the correct box. M 0 6 * * * * * * * * * * * * * 0 0 * * 0 0 * * * * 0 0 F Product M Motor 2, 3 Series Series 4,, 6 Displacement cm3/r [in3/r] 19.8 [11.9] [.04] [19.04] [23.90] [29.99] [38.09] [.00] [49.03] [9.97] 7, 8 Mounting Type AA Bearingless, 4 Bolt: 127,0 [.00] Pilot Dia. and 14, [.6] Dia. Holes 162,0 [6.38] Dia. Bolt Circle AB Standard, 4 Bolt (SAE CC): 127,0 [.00] Pilot Dia. and 14, [.6] Dia. Holes on 162,0 [6.38] Dia. B.C. AC Wheel, 4 Bolt 139,7 [.] Pilot Dia. and 14, [.6] Dia. Holes on 184,2 [7.2] Dia. Bolt Circle AD Standard, 4 Bolt, (SAE D): 2,4 [6.00] Pilot Dia..24 [.600] Dia. Holes on [9.00] Dia. Bolt Circle (SAE D) with O-Ring Groove to Accept ARP-163 O-Ring AH Standard, 4 Bolt: 10.0 [6.] Pilot Dia. 18,01 [.9] Dia. Holes on [7.87] Dia. Bolt Circle. AL - Wheel, 4 Bolt: [6.] Pilot Dia. with.8 [.23] Pilot Length and [.9] Dia. Holes on [7.874] Bolt Circle (ISO Compatible) 9, 10 Output Shaft Description 00 None (Bearingless) 01 38,10 [1.) Dia. Straight Shaft with UNC-2B Thread in End, 9,2 [.37] Sq x 41,28 [1.62] Straight Key 02 44, [1.7] Dia..12:1 Tapered Shaft per SAE J1 with UNEF-2A Threaded Shaft End, 11,11 [.437] Sq. x 31,8 [1.2] Straight Key 03 38,10 [1.] Dia. Flat Root Side Fit, 17 Tooth, 12/24 DP DEG. Involute Spline with UNC-2B Thread in end 40,4 [1.9] Minimum Full Spline Length 04 40,00 [1.7] Dia. Straight Shaft with M12 x 1.7-6H Thread in End, 12W x 8H x 63L [.472W x.313h x 2.480L] Key 12 49,99 [1.968] Dia. Straight Shaft with M12 x 1.7-6H Thread in End, 14W x 9H x L [.W x.4h x 2.76L] Key 60mm Dia. 10:1 Tapered Shaft per ISO R77 with M42 x 3-6H Threaded Shaft End, 16W x 10H x 32L [.6W x.394h x 1.26L] Key 16 3,98 [2.12] Dia. Flat Root Side Fit, 16 Tooth, 8/16 DP Deg. Involute Spline with M12 x 1.7-6H Thread in End,,9 [2.20] Min Full Spline 11, 12 Port Description AA 1, UN-2B SAE O-Ring Ports Staggered Ports AB SAE 19.0 [.7] Dia. 4-Bolt Split Flange - Staggered Ports AC G 1 Staggered Ports AG.7-16 UNF-2B SAE O-ring Ports - Staggered 13, 14 Case Flow UNF-2B SAE O-Ring Port With Check Valve 03 G 1/4 BSP Straight Thread Port with Check Valve UNF-2B SAE O-Ring Port with Shuttle Valve UNF-2B SAE O-ring Ports, External Lubrication Circuit Requires Case Drain must be Connected,.063 Shuttle Flow Orifice Low Pressure Relief 0 None A Set at 4. [6 lbf/in2] B Set at.2 [220 lbf/in2] 16, 17 Pressure/Flow Option 00 None 18 Geroler Option 0 Standard 2 Tight Fitting 19 Seal Option 0 Standard 1 Viton 3 Seal Guard 20, 21 Accessories 00 None 22, 23 Special Features (Hardware) 00 None 01 Non-Masked Nameplate 02 Non-Masked Nameplate, Low Noise Valve Plate 03 Low Noise Valve Plate 24, 2 Special Features (Assembly) 00 None AA Reverse Rotation 26, 27 Paint/Packaging 00 No Paint, Individual Box AA Low Gloss Black Primer AD No Paint, Bulk Box Option AE Low Gloss Black Primer, Bulk Box Option 28, 29 Customer ID 00 None Design Code F Sixth Feature in bold are preferred and allow for shorter lead time C--18 EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011