9 Shaft type N = Metric, to DIN/ISO 3019, Part 2 and VDMA 24560, Part 1 Y = SAE models P*B5 to 15 only. Omit for 20 thru 90 models

Transcription

1 Model Codes P *** -(F)-(M) * *(F)(X) (*)-** -**-(C)-(G)-(L)- ** -**** F V asic models = Fixed displacement type = Variable displacement type 2 Displacement PF and PV models: 5 = 10,55 cm 3 /r (0.64 in 3 /r) 10 = 21,10 cm 3 /r (1.29 in 3 /r) 20 = 42,80 cm 3 /r (2.61 in 3 /r) PV models only: 6 = 13,81 cm 3 /r (0.84 in 3 /r) 15 = 33,00 cm 3 /r (2.01 in 3 /r) 29 = 61,60 cm 3 /r (3.76 in 3 /r) 45 = 94,50 cm 3 /r (5.76 in 3 /r) 90 = 197,50 cm 3 /r (12.0 in 3 /r) 3 Foot mounting option F = Foot mounting option for PV45 and PV90 models. Omit for flange mounting. Note. For foot mounting brackets. for other models see bottom of page. 4 Mounting flange M = Metric, to DIN/ISO 3019, Part 2 and VDM 24560, Part 1 Omit for SE mounting flange 5 Shaft rotation Viewed at shaft end R = Clockwise L = nticlockwise (not avalable for PF10 and PF20) 6 Displacement zone PV models only. S = One side of center (pressure compensated models only) D = oth sides of center (Handwheel and lever controlled models only) Omit for PF models. 7 Flanged main s F = PV45 and PV90 models only. Omit for P*5 to 29 inclusive. 8 Thru shaft option PV5 to 29 only: X = Thru shaft (with side entry s) Omit for PV45 and PV 90, or if not required. 9 Shaft type N = Metric, to DIN/ISO 3019, Part 2 and VDM 24560, Part 1 Y = SE models P*5 to 15 only. Omit for 20 thru 90 models 10 Pump design number 10 = PF20 30 = PF10 31 = PV10 and PV15 20 = all other models 11 Displacement control options PV models only. C = Pressure compensator. Pressure adjustment range: PV90: 19 to 210 bar (275 to 3000 psi) ll other models: 17 to 210 bar (250 to 3000 psi) lso used as prefix for item 12 Note. For PV6, 15 and 29 models, the user must ensure that the max. pressure setting never exceeds 140 or 100 bar (2000 or 1500 psi) dependent on the type of fluid being used. CM = CVP = Pressure compensator. Option for all sizes except PV90. Pressure adjustment range: PV45: 10 to 100 bar (150 to 1500 psi) ll other sizes: (17 to 100 bar (250 to 1500 psi) Load sensing with pressure limiter. PV5 to 15 only: H = Handwheel control M = Lever control V = No control (s for M type but without lever.) Omit for PF models. 12 Maximum displacement adjustment PV5 to 29 models only: C = C or CM compensator, and with 12 Omit when not required. 13 Pressure compensator variations PV5 to 29 models only: G = Remotely adjustable pressure setting. Omit when not required. 14 Control location PV5 to 15 models with H, M or V controls only: L = Left hand, when viewed at shaft end. Omit for right hand, or when a pressure compensator is fitted. 15 Control design number PV models only. 10 = H and M controls; also C control for PV90 11 = C and CM controls. 12 = CVP control. 20 = CG control. 16 Special design options For PF5 and PV5 to 29 only:. S.30 = Extra drain to permit vertical shaft-up installation. For PV5 to PV29 pressure compensated models only: GE1 = 10% minimum displacement. when pressure compensated. For all models: GEVS= Pressure setting knob with key lock. Omit when not required. Foot bracket mounting kits Order separately if required. Kits include pump fixing bolts. Model Part For pump sizes: code number F P*5/6 F P*10/15 and PF20 F-C PV20/29

2 Temperature Limits Minimum ambient C ( 4 F) Maximum ambient C (+158 F) Fluid Temperatures Mineral Watercontaining oil Mininmum 20 C +10 C ( 4 F) (+50 F) Maximum* +80 C +54 C (+176 F) (+129 F) Noise Levels * Typical values equivalent to NFP * To obtain maximum service life from both fluid and hydraulic system, 65 C (150 F) normally is the maximum temperature except for water-containing fluids. Whatever the actual temperature range, ensure that viscosities stay within the limits specified in Hydraulic Fluids section. Drive Requirements: - Direction of Rotation Clockwise or anti-clockwise (viewed at shaft end) to order; see also Model Code, and Installation Dimensions sections. Noise level d()* - Drive Methods Direct co-axial drive through a suitable flexible coupling is preferred. If an indirect drive is to be used, first consult your Vickers representative. Filtration Requirements 20/18/14 or ISO 18/14.. Speed r/min Pressure bar (psi) Stroke PV5 PV6 PV10 PV15 PV20 PV (500) 70 (1000) 140 (2000) 210 (3000) 35 (500) 70 (1000) 140 (2000) 210 (3000) 35 (500) 70 (1000) 140 (2000) 210 (3000) 35 (500) 70 (1000) 140 (2000) 210 (3000) Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff Full flow Cutoff 64 65

3 PF5 SE Flange Mounting Installation Dimensions in mm (inches) Optional foot bracket, shown in dashed outline; kit F--10 comprises foot bracket and two pump fixing bolts bolts. Order separately, if required. Case drain 9 / UNF-2 for SE O-ring fittings: 2 s 4 holes 3 / 8 16 UNC-2 thread (foot bracket) 135 (5.3) 106,4 (4.19) Ø95,3 (3.75 dia) 44,5 (1.75) 142,2 (5.6) 85,9 (3.4) 69,8 (2.75) 34 (1.34) 2 holes Ø11,1 (0.437 dia) (pump flange) 79,2 (3.125) 127,0 (5.0) 152,4 (6.0) Ø130 (5.12 dia) 4 holes Ø11,1 (0.437 dia) 32,5 (1.28) 59,4 (2.34) 93 (3.7) 50,8 (2.0) lternate drain 43,7 (1.72) 43,7 (1.72) ROTTION OUT NI 98,6 (3.9) IN OUT ROTTION 57,2 (2.25) Inlet/outlet s: 1 1 / UNF-2 thread for SE O-ring fittings. View on rear end of pump 7,6 (0.3) 47,3 (1.86) 103,1 (4.06) Ø82,55/82,50 (3.250/3.248 dia) Key: 4,8 (0.19) Square x 25,4 (1.0) long 21,13/21,00 (0.832/0.827) Ø19,05/19,02 (0.750/0.749 dia) 6,4 (0.25) Detail of shaft, key and locating diameter

4 PF10 SE Flange Mounting Installation Dimensions in mm (inches) Optional foot bracket, shown in dashed outline; kit F--10 comprises foot bracket and two pump fixing bolts bolts. Order separately, if required. Ø174,8 (6.88 dia) Ø120,6 (4.75 dia) 2 holes in pump flange: Ø14,3 (0.563 dia) Case drain 3 / 4-16 UNF-2 for SE O-ring fittings: 2 s 87,9 (3.46) 180,8 (7.12) 45,7 (1.80) 92,1 (3.63) 98,6 (3.9) 146 (5.75) 177,8 (7.0) 4 holes: Ø11,2 (0.44 dia) D E 50,8 (2.0) lternative drain 114,3 (4.5) Key: 6,35 (0.25) Square 9,5 (0.375) ROTTION OUT IN 62,7 (2.47) 25,12/24,87 (0.989/0.979) 133,3 (5.25) Ø101,60/101,55 (4.000/3.998 dia) 62,0 (2.44) Inlet/outlet s: 1 5 / 8-12 UNF-2 thread for SE O-ring fittings. View on rear end of pump Ø22,22/22,20 (0.875/0.874 dia) C Detail of shaft, key and locating diameter Pump type C D* E* PF10-*-30 44,4 (1.75) PF10-*Y-30 58,7 (2.31) 213,9 (8.42) 228,1 (8.98) *Omit for foot bracket models) 33,3 (1.31) 47,6 (1.87) 26,9 (1.06) 41,1 (1.62) 59,4 (2.34) 73,7 (2.9)

5 PF20 SE Flange Mounting Installation Dimensions in mm (inches) Optional foot bracket, shown in dashed outline; kit F--10 comprises foot bracket and two pump fixing bolts bolts. Order separately, if required. 2 holes Ø14,3 (0.56 dia) 178,0 (7.0) R.H. Shaft Rotation Ø120,6 (4.75 dia) Ø174,8 (6.9 dia) 58,7 (2.31) Case drain 3 / 4-16 UNF-2 for SE O-ring fittings: 2 s 262,9 (10.32) 130,0 (5.12) 14,2 (0.56) 4 holes Ø11,1 (0.437 dia) 43,7 (1.72) 92,1 (3.63) 181,0 (7.13) 98,3 (3.87) 146,0 (5.75) 171,4 (6.75) 41,0 (1.61) 73,6 (2.9) 92,7 (3.65) 50,8 (2.0) lternative drain 144,3 (5.7) Key: 7,9 (0.31) Square 35,33/35,08 (1.391/1.381) 47,8 (1.88) 9,5 (0.375) 152,4 (6.0) 7,8 (0.31) Shaft rotation 82,5 (3.25) Inlet/outlet s (see table): 1 5 / 8-12 UNF-2 thread for SE O-ring fittings. View on rear end of pump Inlet RH LH Outlet 73,2 (2.88) 146,0 (5.75) Ø101,60/101,55 (4.000/3.998 dia) Ø31,75/31,70 (1.250/1.248 dia) Detail of shaft, key and locating diameter

6 PV5/6 SE Flange Mounting: Pressure Compensator Control - C and CM Installation Dimensions in mm (inches) See also Control Data section, page (5.3) Height of foot bracket Compensator position for: R.H. rotation models L.H. rotation models R.H. Shaft Rotation 106,4 (4.19) Optional foot bracket, shown in dashed outline; kit F--10 comprises foot bracket and two pump fixing bolts bolts. Order separately, if required. R20,6 (0.8 rad) Case drain 9 / UNF-2 for SE O-ring fittings: 2 s 44,4 177 (6.9) (1.75) 162,8 (6.41) 108,7 (4.23) 69,8 (2.75) 69,8 (2.75) R47,8 (1.9 rad) 33,5 (1.32) 4 holes 3 / 8 16 UNC-2 thread (foot bracket) 79,4 (3.125) 127,0 (5.0) 152,4 (6.0) 2 holes Ø11,1 (0.437 dia) (pump flange) Ø130 (5.12 dia) 4 holes Ø11,1 (0.437 dia) 59,4 (2.34) 93 (3.7) 50,8 (2.0) 163,5 (6.44) Caution: While pump is operating do not back compensator adjustment screw out beyond dimension shown. 84,8 (3.34) 28,4 (1.12) Key: 4,8 (0.19) Square x 25,4 (1.0) long 21,13/21,00 (0.832/0.827) 79,2 (3.12) Ø82,55/82,50 (3.250/3.248 dia) 38,1 (1.50) 57,2 (2.25) 135,9 (5.35) 52,3 (2.06) lternate drain Ø19,05/19,02 (0.750/0.749 dia) 6,4 (0.25) Detail of shaft, key and locating diameter Inlet/outlet s (see table): 1 1 / UNF-2 thread for SE O-ring fittings. View on rear end of pump Shaft rotation Inlet RH LH Outlet

7 PV5/6 Thru-Shaft Models (with Side Ports) Installation Dimensions in mm (inches) Maximum output torque is 40 Nm (354 lbf in), less unput torque at system pressure, see performance curves: t 1500 r/min drive speed, page.8. t 1800 r/min drive speed, page.12. For other dimensions and installation data see page ,2 (6.03) 4,77/4,75 (0.188/0.187) square key both ends 17,91/17,78 (0.705/0.700) Outlet for RH rotation models; Inlet for LH rotation models: 1 5 / UN-2 thread for SE O-ring fittings. 29,5 (1.16) 177,0 (6.97) 213,4 (8.40) Ø15,82/15,8 (0.623/0.622 dia) Inlet for RH rotation models; Outlet for LH rotation models: 1 5 / UN-2 thread for SE O-ring fittings. 165,1 (6.50) 73,15 (2.88) 51,3 (2.02)

8 PV10/15 SE Flange Mounting Pressure Compensator Control - C and CM Installation Dimensions in mm (inches) See also Control Data section, page.15. Compensator position for: R.H. rotation models L.H. rotation models Ø120,6 (4.75 dia) Optional foot bracket, shown in dashed outline; kit F--10 comprises foot bracket and two pump fixing bolts bolts. Order separately, if required. 58,7 (2.31) Ø174,8 (6.88 dia) 74,7 (2.94) Case drain UNF-2 for SE O-ring fittings: 2 s 123,7 (4.87) 207,8 (8.18) 193,8 (7.63) UNC -2 thd. 4 holes 2 holes Ø14,3 (0.563 dia) 98,6 (3.9) 28,4 (1.12) 52,3 (2.1) 146 (5.75) 187 (7.36) 45,7 (1.80) Caution: While pump is operating do not back compensator adjustment screw out beyond dimension shown. R.H. Shaft Rotation 89,3 (3.5) max 84,8 (3.34) 137,1 (5.4) max 23,9 (0.94) 92,1 (3.63) 174,6 (6.9) 4 holes Ø11,2 (0.44 dia) 28,4 (1.12) 82,5 (3.25) 65 (2.56) 41,1 (1.62) 73,7 (2.9) Ø101,60/101,55 (4.000/3.998 dia) 189,0 (7.44) Key: 6,4 (0.25) Square x 22,3 (0.88) long 9,5 (0.375) 25,12/24,87 (0.989/0.979) 50,8 (2.0) 66,5 lternative drain (2.62) Inlet/outlet s (see table): UN-2 thread for SE O-ring fittings. View on rear end of pump Shaft rotation Inlet RH LH Outlet Ø22,22/22,20 (0.875/0.874 dia) 47,8 (1.88) Detail of shaft, key and locating diameter

9 PV10/15 Thru-Shaft Models (with Side Ports) Maximum output torque is 83 Nm (735 lbf in), less unput torque at system pressure, see performance curves: t 1500 r/min drive speed, pages.8 &.9. t 1800 r/min drive speed, page.12 & ,5 (6.87) For other dimensions and installation data see page.22. 4,79/4,76 (0.1885/0.1875) square key x 25,4 (1.0) long 21,13/21,00 (0.832/0.827) Outlet for RH rotation models; Inlet for LH rotation models: 1 5 / 8-12 UN-2 thread for SE O-ring fittings. 31,75 (1.25) 308,8 (12.16) Ø19,05/19,02 (0.750/0.749 dia) Inlet for RH rotation models; Outlet for LH rotation models: 1 5 / 8-12 UN-2 thread for SE O-ring fittings. 196,9 (7.75) 90,4 (3.56) 65,3 (2.57)

10 PV5/6 and PV10/15 Manual/Mechanical Controls Lever Control - M and No Control - V Units with this control may be operated on both sides of center permitting bi-directional fluid flow characteristics. 35 R 9,7 (0.38 rad) 76,2 (3.0) 6,4 (0.25) Position 1 Position 2 Ø6,4 (0.25 dia) 127 (5.0) Shaft rotation RH LH Lever position 1 2 Handwheel Control - H Max. flow adjustment. djust and lock to limit max. flow. 15,7 (0.62) Outlet Units with this control may be operated on both sides of center permitting bi-directional fluid flow characteristics. Ø17,40/17,27 (0.685/0.680 dia) 15,7 (0.62) 1 2 No Control - V 37,3 (1.47) Lever may be set at any position in 360 circle. Ensure clamp bolt is fully tightened. Position 1 Ø57,2 (2.25 dia) Ø6,3 (2.25 dia) Pump type PV5/6 153 (6.02) PV10/ (8.04) C R24 (0.95 rad) 68,9 (2.7) 99,9 (3.93) Caution! Loosen lock screw before turning handle. Re-tighten after adjusting flow. 62 (2.5 ) max. 43,7 (1.72 ) 65,7 (2.6) Position 2 35,3 (1.39) Shaft rotation RH LH Pointer position Handwheel rotation from zero Clockwise Counter-clockwise Clockwise Counter-clockwise Outlet Pump type PV5/6 200 (7.87) PV10/ (9.84) 129 (5.08) 140 (5.51) C 70,6 (2.78) 93,5 (3.68)

11 PV20/29 SE Flange Mounting Pressure Compensator Control - C and CM Installation Dimensions in mm (inches) See also Control Data section, page holes Ø17,5 (0.69 dia) 4 holes Ø17,5 (0.69 dia) R.H. Shaft Rotation 226,0 (8.9) 181,0 (7.125) Optional foot bracket, shown in dashed outline; kit F-C-10 comprises foot bracket and two pump fixing bolts bolts. Order separately, if required. 58,9 (2.32) Ø146,0 (5.75 dia) Ø212,8 (8.38 dia) 53,8 (2.1) 109,5 (4.31) 215,9 (8.5) 15,7 (0.62) 84,8 (3.44) Case drain UNF-2 for SE O-ring fittings: 2 s 123,4 (4.86) 221,7 (8.73) 295,0 (11.62) 15,7 (0.62) 50,8 (2.0) 234,9 (9.25) 265,2 (10.5) 50,8 (2.0) 39,9 (1.6) 19,0 (0.75) 128,5 (5.1) 17,3 (0.68) 76,2 (3.0) Caution: While pump is operating do not back compensator adjustment screw out beyond dimension shown. 28,4 (1.12) 84,8 (3.34) 41,1 (1.62) Key: 7,9 (0.31) Square x 31,7 (1.25) long 9,5 (0.37) 66,5 (2.62) 95,2 (3.75) 59,2 (2.3) 189,0 (7.44) Ø127,00/126,95 (5.000/4.998 dia) 35,33/35,08 (1.391/1.381) 82,5 (3.25) lternative drain Inlet/outlet s (see table): UNF-2 thread for SE O-ring fittings. View on rear end of pump Shaft rotation Inlet RH LH Outlet Ø31,75/31,70 (1.250/1.248 dia) 47,7 (1.88) Detail of shaft, key and locating diameter

12 PV20/29 Thru-Shaft Models (with Side Ports) Maximum output torque is 159 Nm (1408 lbf in), less unput torque at system pressure, see performance curves: t 1500 r/min drive speed, page.9 t 1800 r/min drive speed, page.13 For other dimensions and installation data see page ,1 (12.05) 365,25 (14.38) 85,3 (3.36) Key: 6,35 (0.25) square x 25,4 (1.0) long 29,96 (1.14) 69,85 (2.75) 93,2 (3.67) Ø38,1 (1.50 dia) 235,7 (9.28) 35,7 (1.406) 277,1 (10.91) Ø25,37/25,35 (0.999/0.998 dia) UNC-2 thread 8 places for 1 1 / 2 SE 4-bolt flange 58,9 (2.32) min. Port : Outlet for RH rotation models. Inlet for LH rotation models. 111,2 (4.38) 148,8 (5.86) 260,0 (10.24) Port : Inlet for RH rotation models. Outlet for LH rotation models.

13 PV45 Flange-Mounted Model Compensator adjuster: 38,1 (1.5) /F hex. 81,79 (3.22) 145,3 (5.72) 407,0 (16.0) 308,0 (12.13) 15,75 (0.62) Drain connection: UNF 2 thread for SE O-ring fittings (2 s). Key 38,1 (1.5) 11,1 (0.437) square Ø152,4/152,35 (6,000/5.998 dia) 49,43 (1.945/1.935) Ø44,45/44,40 (1.750/1.748 dia) 35,0 (1.38) CUTION: While pump is operating do not back compensator adjuster screw out beyond this dimension. 110,3 (4.34) 66,67 (2.625) 187,4 (7.38) lternative drain UNC 2 thread x 12,0 (0.47) deep for lifting eye-bolt. 299,0 (11.77) 4 slots 19,8 (0.78) wide for mounting bolts. (Use of backing washers is recommended) 127,0 (5.0) (12.3) 290 (11.42) 161,6 (6,34) square 77,8 (3.062) IN OUT 101,6 (4.0) 141,0 (5,55) 200,2 (7,88) square View on shaft end of pump Direction of shaft rotation To suit SE 4-bolt flanges: 8 holes UNC 2 thread x 27,0 (1.06) deep 42,9 (1.688) 2 s Ø50,8 (2.0 dia) View on rear end of pump

14 PV45 Foot-Mounted Model For other dimensions and installation data see page ,1 (2.72) 66,67 (2.625) 317,4 (12.5) 165,1 (6,5) square 146,0 (5.75) 62 (2.5) 4 holes Ø16,7 (0.68 dia) 282,6 (11.125) 333,4 (13.125) 352,6 (13.9) 62 (2.5) 25,4 (1,0) 104,4 (4.1) 60,4 (2.38) 165,1 (6.5) 206,5 (8.13) 21,8 (0.86) 60,4 (2.38) 1 hole Ø8,5 (0.335 dia) for dowelling; front foot only 1 hole Ø8,5 (0.335 dia) for dowelling; rear foot only

15 PV90 Foot mounting option (designated by Model Code = F ) is shown in dotted outline. n alternative base mounting facility is provided by four tapped holes in the bottom face of the pump - see page.30. Compensator adjuster: 38,1 (1.5) /F hex. Drain connection: UN 2 thread for SE O-ring fittings (2 s). Key 11,1 (0.437) square x 44,5 (1.75) long 68,25 (2.69) 38,1 (1.5) 156,5 (6.16) 351,5 (13.84) 365 (14.4) 35,0 (1.38) 396,7 (15.62) CUTION: While pump is operating do not back compensator adjuster screw out beyond this dimension. 49,40/49,15 (1.945/1.935) 127,0 (5.0) 111,2 (4.38) Ø152,4/152,35 (6,000/5.998 dia) Ø44,45/44,40 (1.750/1.748 dia) Location of tappings for lifting eye-bolts,: 2 at shaft end; 1 at rear: UNC 2 thread x 12,0 (0.47) deep. 79,2 (3.12) 329 (12.95) Ø228,6 (9.0 dia) 4 holes Ø20,6 (0.81 dia) at 45 from vertical/ horizontal center lines. 63,5 (2.5) center line to drain 130,0 (5.12) 187,5 (7.38) 215,9 (8.5) 260,3 (10.25) 2 s Ø60,4 (2.4 dia) Drain connection: UN 2 thread 4 holes Ø16,7 (0.66 dia) 88,9 (5.5) 139,7 (5.5) 163,8 (10.24) 167,6 (10.48) 200 (7,9) square 50,8 (2.0) 190,5 (7.5) 139,7 (5,5) 393,7 (15.5) 438,1 (17.25) View on shaft end of pump To suit SE 4-bolt flanges: 8 holes UNC 2 thread x 27,0 (1.06) deep View on rear end of pump Shaft rotation Inlet RH LH Outlet

16 PV90 cont d Detail of tappings in base of pump. Shaft end of pump 2 (8.375) 130,2 (5.125) 4 holes tapped UNC-2 x 28 (1.1) deep PV5/6, PV 10/15 and PV20/29 with Pressure Compensator and djustable Maximum Displacement Stop: Control Types CC and CMC For general dimensions and installation data of these pumps, see pages.20,.22 and.25 Caution: While pump is operating do not back compensator adjustment screw out beyond dimension shown. Fully extended 17,3 (0.68) D C G Note. Compensator position for: PV5/6-*LSY (LH rotation models) and PV10/15 -*RSY (RH rotation models) PV20/29 -**SY (RH and LH rotation models) 28,4 (1.12) F H E 28,4 (1.12) 23.9 (0.94 /F djusting rod Pump type PV5/6 233 (9.17) PV10/ (10.47) PV20/ (11.56) 195 (7.68) 226 (8.9) 254 (10.0) C 50 (1.97) 52,3 (2.06) 66,5 (2.62) Minimum delivery position (screw flush with nut); do not adjust below flush. D 22,9 (0.9) 25,1 (0.99) 41,9 (1.65) E 76,2 (3.0) 118 (4.65) F 94,4 (3.72) 70,8 (2.79) _ 53,3 (2.1) G 94,4 (3.72) 90,2 (3.55) 104,4 (4.11) H _ 23,8 (0.94) 41,1 (1.62) Note. Compensator position for: PV5/6-*RSY (RH rotation models) and PV10/15 -*LSY (LH rotation models)

17 PV5 to 29 with CG Remote Control of Compensator Type GEVS 43 (1.7) 74,6 (2.94) Ø35 (1.4 dia) Location as shown for: PV5/6 LH rotation models, PV10/15 RH rotation models and PV20/29 LH and RH rotation models. 45,0 (1.77) UNF-2 thread for SE CG control models, connect to external valve. Note. Do not operate pump with this plugged. Location as shown in dotted outline for: PV5/6 RH rotation models and PV10/15 LH rotation models. Caution: Effective compensator setting will be compensator control setting plus remote relief valve setting. djustment procedure 1. Turn remote pressure control (such as C-175) anti-clockwise to minimum setting. 2. Turn compensator adjustment plug to desired minimum pressure - 17 bar (250 psi) or higher. 3. Full pressure range can now be obtained with remote pressure control. CVP Load Sensing with Pressure Limiter 55,0 (2.17) 40,69 (1.6) 22,0 (0.87) 45,5 (1.8) Load sensing control : UNF-2 thread for SE O-ring fittings. 19,0 (0.75) Location as shown for: PV5/6 LH rotation models, PV10/15 RH rotation models and PV20/29 LH and RH rotation models. Ø28,5 to mounting (1.12 dia) face PV5/ (7.51) PV10/ (8.75) PV20/ (9.84) Vertical Shaft-up Installation - S30 Drain Port Option, for PV5 to 29 dditional drain Pump Port tapping type PF UNF-2 28,7 (3.85) PV5/ UNF-2 19 (0.75) PV10/ UNF-2 29,3 (1.15) PV20/ UNF-2 38,9 (1.53)

18 PV5/6; PV10/15; PV20/29 DIN/ISO Models For dimensions/data not shown refer to corresponding SE models. PV5/6 Pressure Compensated Control C and CM Key: 6,0 (0.236) square x 22,5 (0.89) long 22,5 (0.886) 44,5 (1.75) 7,24 (0.285) Ø80,0 (3.15 dia) 2 holes Ø11,3 (0.44 dia) 109,0 (4.29) Ø20,0 (0.787 dia) 36,0 (1.42) PV10/15 Pressure Compensated Control C and CM Key: 8,0 (0.315) square x 28,0 (1.1) long 28,0 (1.1) 52,5 (2.07) 9,24 (0.364) Ø100,0 (3.937 dia) 2 holes Ø14,25 (0.56 dia) 140 (5.51) Ø25,0 (0.984 dia) 42,0 (1.65) PV20/29 Pressure Compensated Control C and CM Key: 10,0 (0.39) square x 35,0 (1.38) long 35,0 (1.38) 68,9 (2.71) 9,24 (0.364) Ø125,0 (4.92 dia) 2 holes Ø18,25 (0.72 dia) 180,0 (7.08) Ø32,0 (1.26 dia) 58,0 (2.28)