Performance Information Series PVP 100/140 Pressure Compensated, Variable Volume, Piston Pumps

Transcription

1 Catalog HY /US Technical Information Series PVP 1/14 Performance Information Series PVP 1/14 Compensated, Variable Volume, Piston Pumps Features High Strength Cast-Iron Housing for Reliability and Quiet Operation Replaceable Bronze Port Plate to llow Easy Field Serviceability Replaceable Piston Slipper Plate Thru-Shaft Capability SE, B and C Pilots vailable Low Noise Levels Fast Response Times Metric Pilot Shaft and Ports vailable Low Control s for Reduced Draw (Energy Efficient) Controls Compensation Remote Compensation Load Sensing djustable Maximum Volume Stop Low Standby Hi/Lo Torque () Limiting Schematic Symbol (Basic Pump) Special Installation or Fluids Consult your Parker Representatives on applications requiring higher than rated pressure, over-speed conditions, indirect drive, fluids other than mineral base fluid, and operation at temperatures above 71 C (16 F). Quick Reference Data Chart Pump Model hpm12-1.p65, lw, jk Displacement cc/rev (In 3 /rev) Specifications Ratings Outlet Port: 248 bar (36 ) Continuous (P1) 31 bar (45 ) Peak (P3) Inlet Port: 1.72 bar (25 ) Maximum. bar ( In. Hg.) Vacuum 18 RPM Case Drain:.3 bar (5 ) Maximum Differential over Inlet Port. 1. bar (15 ) Maximum Speed Ratings: 6 to 18 RPM Operating Temperature Range: 4 C to 71 C ( 4 F to 16 F) Housing Material: Cast-Iron Filtration: ISO 16/13 Recommended ISO 18/15 Maximum Mounting: SE C 2-Bolt or Diagonally on a SE C 4-Bolt SE D 2-Bolt or Diagonally on a SE D 4-Bolt Metric 2-Bolt Installation Data: See Installation Information on page 244 for specific recommendations pertaining to system cleanliness, fluids, start-up, inlet conditions, shaft alignment, drain line restrictions and other important factors relative to the proper installation and use of these pumps. Pump Delivery *pprox. Noise Levels db() Input 7 bar (1 Full 18 RPM (12 RPM) 18 RPM, Max. in LPM () 34 bar bar bar 27 bar 248 bar Displacement & 12 RPM 18 RPM (5 ) (1 ) (2 ) (3 ) (36 ) 248 bar (36 ) PVP1 1. (6.1) 12. (31.7) 18. (47.5) 73 (67) 75 () 78 (72) 79 (75) 81 (75) 83.6 kw (112. hp) PVP (8.54) 171. (45.5) 252. (67.) 8 (71) 8 (72) 8 (75) 82 (76) 84 (77) kw (158. hp) * Since many variables such as mounting, tank style, plant layout, etc., effect noise levels, it cannot be assumed that the above readings will be equal to those in the field. The above values are for guidance in selecting the proper pump. Noise levels are -weighted, mean sound pressure levels at 1 meter from the pump, measured and recorded in accordance with applicable ISO and NFP standards. 194

2 Catalog HY /US Ordering Information Series PVP 1/14 PVP Displacement Painting Multiple Pump Shaft Port Rotation Volume Thru- Thru- Control Seals Multiple Pumps Variable Range Option Stop Shaft Shaft Option Pumps Piston Option Threads Option Maximum Displacement CC s/rev. (Cu.In s/rev.) 1 1 CC/Rev (6.1) CC/Rev (8.5) R L Rotation * Right (CW) Left (CCW) * Viewed from shaft end. P Painting No Paint Paint Multiple Pumps Range* bar (25-1 ) bar (25-2 ) bar (25-3 ) bar (25-36 ) * Minimum value of pressure range only applies on control option omit code. Multiple Pumps Single Pump Factory Mounted To Rear of nother Pump Vol. Stop Option Thru-Shaft Thds No Thru-Shaft 6* UNC 9** Metric * vailable with 2 port option. ** vailable with 8 or 9 port option. No Volume Stop 2 dj. Max. Vol. Stop V Nitrile Single Pump Pump Factory Mounted On Rear Seals Fluoroelastomers* * FLUOROELSTOMERS are available under various registered trademarks, including FLUOROCRBON (a registered trademark of DuPont) and FLUOREL (a registered trademark of 3M). Control Option Standard Comp. M Remote (Master) ME Remote (Slave) Shaft Pilot * 1-1/4" Keyed (SE C) SE C B* 14T Spline (SE C) SE C C 1-1/2" Keyed (SE CC) SE C D 17T Spline (SE CC) SE C E 1-3/4" Keyed (SE D) SE D F 13T Spline (SE D) SE D G 1-3/4" Keyed (SE D) SE C H 13T Spline (SE D) SE C K 4mm Keyed Metric * Maximum torque is 639. N m (568 In-Lbs). vailable with 8 or 9 porting options only. 4 B3 HLM* HL* S Thru-Shaft Option No Thru-Shaft and Remote and Hi/Lo,, and Hi/Lo Servo Vol. & (Int) SF Servo Vol. & (Ext) * Specify, RPM & comp setting when ordering or will be get default. SE Pilot / SE 9T Spline SE B Pilot / SE B 13T Spline B4 SE B Pilot / SE BB 15T Spline C3 SE C Pilot / SE C 14T Spline Port Option Port Type 2 Side Flange (Inch) SE 8 Side Flange (Metric Thds.) ISO 6149 hpm12-1.p65, lw, jk 9 Side Flange (Metric Thds.) BSPP 195

3 Catalog HY /US Performance Data Series PVP 1/14 Typical Performance Data - Fluid: Standard Hydraulic Oil 1 49 C (12 F) LPM RPM Full LPM RPM 1 Full Note: Compensated horsepower curves are shown for the standard pressure compensator option. For remote type compensators the compensated horsepowers will be 1-15% higher. Note: The efficiencies and data in the graphs are accurate for pumps running at speeds shown and maximum stroke. To calculate approximate horsepower for other conditions, use the following formula... = [ Q x () + Compensated 1714 ] LPM RPM Full PVP 1/14 Inlet Characteristics at Full Displacement (Graph only valid at sea level) Inlet Vacuum bar hpm12-1.p65, lw, jk bar In-Hg Recommended Operating Condition DO NOT OPERTE IN THIS REGION Shaft Speed - RPM LPM PVP 1/14 pproximate Case Drain verage of 12, 15 & RPM Std. Comp. Remote Comp. Full flow

4 Catalog HY /US Performance Data Series PVP 1/14 Typical Performance Data - Fluid: Standard Hydraulic Oil 1 49 C (12 F) LPM RPM LPM RPM Full Full Note: Compensated horsepower curves are shown for the standard pressure compensator option. For remote type compensators the compensated horsepowers will be 1-15% higher. Note: The efficiencies and data in the graphs are accurate for pumps running at speeds shown and maximum stroke. To calculate approximate horsepower for other conditions, use the following formula... = [ Q x () + Compensated 1714 ] LPM Response Times 18 RPM 1 Full Time (millisec) hpm12-1.p65, lw, jk PVP 18 RPM 1 2 On-Stroking De-Stroking Time (millisec) PVP 18 RPM 1 2 On-Stroking De-Stroking

5 VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS ROTTION RPM Catalog HY /US Dimensional Data Series PVP 1/14 Side Ported Option 2 Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation, side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port and compensator on opposite side as viewed from rear of pump. 2. Pump shown with standard pressure compensator (control option omit ). 3/8 X 1-3/8 WOODRUFF KEY (1.66) (1.65) 5/16 X 1 WOODRUFF KEY (1.39) 35.8 (1.38) (1.25) ø 31.7 (1.24) (2.18) SHFT OPTION OMIT (SE C ) MX TORQUE = 639. N m (5,68 IN-LBS) (.437)/11.6 (.435) SQURE X 1.5 LONG KEY (1.94) (1.93) (2.18) SHFT OPTION B (SE C ) 14 TOOTH 12/24 PITCH MX TORQUE = 639. N m (5,68 IN-LBS) (2.43) SHFT OPTION C (SE CC ) MX TORQUE = N m (1,78 IN-LBS) DRIN PORT OPTION 2 - SE-12 STRIGHT THRED (1-1/16-12 UN) ø 38.1 (1.5) 38.5 (1.49) (2.43) SHFT OPTION D (SE CC ) 17 TOOTH 12/24 PITCH MX TORQUE = N m (1,78 IN-LBS) CLERNCE FOR ø.625 MOUNTING BOLT (SE C MOUNTING PTTERN) ø (1.75) 44.4 (1.74) (2.94) SHFT OPTION E or G (SE D ) MX TORQUE = N m (15, IN-LBS) DJUSTBLE MX VOLUME STOP OPTION FLOW CHNGE: PVP1 = 6.25 CC/REV/TURN PVP14 = 8.72 CC/REV/TURN PPROX (12.78) T FULL FLOW (2.94) SHFT OPTION F or H (SE D ) 13 TOOTH 8/16 PITCH MX TORQUE = N m (15, IN-LBS) (1.55) 127. (5.) (4.8) HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CC/REV MX (4.8) SE D ø152.4 (6.) (5.998) Front View 9.42 (3.56) (4.5) 13.5 (5.12) 9.42 (3.56) (4.5) 13.5 (5.12) (3.4) CLERNCE FOR ø.75 MOUNTING BOLT (SE D MOUNTING PTTERN) Top View PRESSURE COMPENSTOR DJUSTMENT SENSITIVITY: PPROX BR (8 ) PER TURN (6.1) MIN PRESSURE 2.3 (.8) (3.54) 11.9 (3.98) IN OUT (4.55) (5.11) (3.54) SE C ø 127. (5.) (4.998) (4.42) LTERNTE DRIN PORT (USE IF PUMP IS INVERTED) OPTION 2 - SE-12 STRIGHT THRED (1-1/16-12 UN) hpm12-1.p65, lw, jk 63.5 (2.5) Rear View INLET - 2-1/2" SE 4 BOLT FLNGE STNDRD PRESSURE SERIES (CODE 61) - OPPOSITE SIDE (1/2-13 THRED FOR PORT OPTION 2 PUMPS) (13.45) (11.35) (1.53) (.49) 19.5 (.75) Side View OUTLET - 1-1/2" SE 4 BOLT FLNGE HIGH PRESSURE SERIES (CODE 62)- THIS SIDE (5/8-11 THRED FOR PORT OPTION 2 PUMPS) 198

6 VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS ROTTION RPM Catalog HY /US Dimensional Data Series PVP 1/14 Side Ported Options 8 & 9 Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port, and compensator on opposite side as viewed from rear of pump. 2. Pump shown with standard pressure compensator (control option omit ). See page 239 for installation dimensions of remote compensator (control options M, ME, or ). Pilot Dimensions Shaft Option Dia. B C D, B, C, D, G, H 127./ (5./4.998) (.49) 9.42 (3.56) (.625) E, F 152.4/ (6./5.998) (.49) (4.5) 19.5 (.75) K / (4.921/4.919) 9.53 (.38) 9 (3.54) Ø18 (.78) 5/16 X 1 WOODRUFF KEY (1.39) 35.8 (1.38) ø31.75 (1.25) 31.7 (1.24) (2.18) SHFT OPTION OMIT (SE C ) MX TORQUE = 639. N m (5,68 IN-LBS) (.437)/11.6 (.435) SQURE X 1.5 LONG KEY (1.94) (1.93) (2.18) SHFT OPTION B (SE C ) 14 TOOTH 12/24 PITCH MX TORQUE = 639. N m (5,68 IN-LBS) 3/8 X 1-3/8 WOODRUFF KEY (1.66) (1.65) ø38.1 (1.5) 38.5 (1.49) (2.43) SHFT OPTION C (SE CC ) MX TORQUE = N m (1,78 IN-LBS) 12 X 8 X 7 MM KEY 43. (1.3) (1.682) (2.43) SHFT OPTION D (SE CC ) 17 TOOTH 12/24 PITCH MX TORQUE = 1212 N m (1,78 IN-LBS) (2.94) ø (1.75) 44.4 (1.74) SHFT OPTION E or G (SE D ) MX TORQUE = 1687 N m (15, IN-LBS) (2.94) SHFT OPTION F or H (SE D ) 13 TOOTH 8/16 PITCH MX TORQUE = 1687 N m (15, IN-LBS) 4. (1.574) ø (1.572) (3.62) SHFT OPTION K (4MM) ONLY VILBLE WITH 125MM PILOT MX TORQUE = 14 N m (12,45 IN-LBS) DRIN PORT OPTION 8 - ISO (M27X2.) OPTION 9-3/4" BSPP D MOUNTING 2-BOLT PTTERN DJUSTBLE MX VOLUME STOP OPTION FLOW CHNGE: PVP1 = 6.25 CC/REV/TURN PVP14 = 8.72 CC/REV/TURN PPROX (12.78) T FULL FLOW (1.55) 127. (5.) (4.8) HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CC/REV MX (4.8) C C Front View Top View 13.5 (5.12) 13.5 (5.12) (3.4) PRESSURE COMPENSTOR DJUSTMENT SENSITIVITY: PPROX BR (8 ) PER TURN (6.1) MIN PRESSURE (3.54) 2.3 (.8) IN (4.55) (5.11) 11.9 (3.98) (3.54) (4.42) LTERNTE DRIN PORT (USE IF PUMP IS INVERTED) OPTION 8 - ISO (M27X2.) OPTION 9-3/4" BSPP hpm12-1.p65, lw, jk 63.5 (2.5) M6X1. THREDS FOR THRU-SHFT MOUNTING Rear View OPPOSITE SIDE INLET 2-1/2" SE 4-BOLT FLNGE STNDRD PRESSURE SERIES (CODE 61) M12X1.75 THRED (13.45) (11.35) (1.53) 19.5 (.75) THIS SIDE OUTLET 1-1/2" SE 4-BOLT FLNGE HIGH PRESSURE SERIES (CODE 62) M16X2. THRED B Side View 199

7 CC/REV MX HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS ROTTION RPM Catalog HY /US Dimensional Data Series PVP 1/14 Thru-Shaft Pump Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation, side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port and compensator on opposite side as viewed from rear of pump. 2. Pump shown with standard pressure compensator (control option omit ). 3. Maximum torque transmitting capacity for rear mounting of pumps = 639. N m (568 In-Lbs). Lower allowables may apply based on pump mounted on rear. C C Top View SHFT LENGTH OF RER PUMP F IN OUT D Front View DPTER MY BE ROTTED 9 IF DESIRED øb E (13.1) Side View Dimensions Thru Shaft Options VRITION B C D E F (14.35) 82.58/82.6 (3.251/3.252) (2.9) 3/8-16UNC-2B 9 Tooth 16/32 Pitch 31.8 (1.25) 6B () 11.63/11.65 (4.1/4.2) 73.3 (2.88) 1/2-13UNC-2B 13 Tooth 16/32 Pitch 41.1 (1.62) 6B () 11.63/11.65 (4.1/4.2) 73.3 (2.88) 1/2-13UNC-2B 15 Tooth 16/32 Pitch 46. (1.81) 6C (15.28) 127.3/127.5 (5.1/5.2) 9.5 (3.56) 5/8-11UNC-2B 14 Tooth 12/24 Pitch 55.4 (2.18) (14.35) 82.58/82.6 (3.251/3.252) (2.9) M1 X Tooth 16/32 Pitch 31.8 (1.25) 9B () 11.63/11.65 (4.1/4.2) 73.3 (2.88) M12 X Tooth 16/32 Pitch 41.1 (1.62) 9B () 11.63/11.65 (4.1/4.2) 73.3 (2.88) M12 X Tooth 16/32 Pitch 46. (1.81) 9C (15.28) 127.3/127.5 (5.1/5.2) 9.5 (3.56) M16 X Tooth 12/24 Pitch 55.4 (2.18) hpm12-1.p65, lw, jk 2

8 VRIBLE VOLUME PUMP INITIL FCTORY SETTINGS ROTTION RPM Catalog HY /US Characteristics Series PVP 1/14 Remote Compensator Pump Dimensions * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port, and compensator on opposite side as viewed from rear of pump. 2. When controlling pump compensator pressure with remote relief valve, size relief valve to pass a minimum of 1.89 LPM (.5 ). HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CC/REV MX DPTOR FITTING SUPPLIED WITH PORT OPTION 8 PUMPS ISO (M12X1.5) 17.2 (.67) 13 (6.58) REF SE -4 STRIGHT THRED O-RING PORT (7/16-2 UNF-2B) INTERNL ORIFICE INSTLLED IN OPTIONS ME & Top View (7.14) PPROXIMTE (7.33) PPROXIMTE (9.29) DPTOR FITTING SUPPLIED WITH PORT OPTION 9 PUMPS (.9) 1/4" BSPP PRESSURE COMPENSTOR DJUSTMENT SENSITIVITY: PPROX BR (12 ) PER TURN DIFFERENTIL PRESSURE DJUSTMENT SENSITIVITY: PPROX BR (4 ) PER TURN (INCLUDED ON CONTROL OPTION) 13 (6.58) REF (3.4) 13 (6.58) Side View Front View hpm12-1.p65, lw, jk 21

9 VRIBLE VOLUME PUMP CC/REV MX INITIL FCTORY SETTINGS ROTTION RPM Catalog HY /US Dimensional Data Series PVP 1/14 Hi/Lo (Torque) Control Pump Dimensions *U.S. Patent #6,95,76 * Inch equivalents for millimeter dimensions are shown in (**). NOTES: 1. Righthand (CW) rotation side ported pump shown. Lefthand (CCW) pumps have inlet port, outlet port, cover drain port, and compensator on opposite side as viewed from rear of pump. 2. When controlling pump compensator pressure with remote relief valve, size relief valve to pass a minimum of 1.89 LPM (.5 ). OPTIONL MX VOLUME STOP Typical Hi-Lo Control / Characteristics HYDRULIC PUMP/MOTOR DIVISION Otsego, MI 4978 MDE IN US CONSTNT POWER CURVE Outlet LOW PRESSURE DJUSTMENT MX. DJUST LOW FLOW SETTING DJUSTMENT System Top View MXIMUM PRESSURE DJUSTMENT LOW FLOW SETTING DJUSTMENT (6.21) (2.31) LOW PRESSURE DJUSTMENT Side View Front View hpm12-1.p65, lw, jk 22

10 Catalog HY /US Characteristics Series PVP 1/14 % of Full Low Knee Typical Hi-Lo Characteristics 34 5 MXIMUM PRESSURE (See Chart 1) FLOW 13.8 BR (2 ) 13.8 BR (2 ) BELOW COMPENSTOR SETTING (See Chart 2) High Knee (Typical) 2 COMPENSTOR SETTING Determining how much the pressure will increase at the Low Knee by manually destroking the pump. 1. From Chart 1 read the maximum obtainable pressure (P1) at the low pressure knee at the input power desired for the desired speed (N). 2. Calculate the theoretical full flow (Q1) of the pump at the desired speed. (cc/rev) X (N) Q1 (gpm) = Pick a reduced output flow (Q2). This is done by decreasing the output of the pump using the optional volume stop. 4. pproximate the new maximum pressure at the low pressure knee for the input power desired (P2). Q1 X P1 P2 = Q2 Chart 1: Max Full PVP1 Full Input 12 RPM RPM 18 RPM Chart 1: Max Full PVP14 Full Input 12 RPM RPM 18 RPM Chart 2: PVP (2 ) Below Compensator Setting Maximum LPM (pplies at speeds of 12 thru 18 RPM) Maximum at 15 RPM Maximum at 12 RPM 172 (25 ) (2 ) 27 (3 ) 248 (36 ) Chart 2: Maximum LPM PVP (2 ) Below Compensator Setting (pplies at speeds of 12 thru 18 RPM) Maximum at 15 RPM Maximum at 12 RPM 172 (25 ) (2 ) 27 (3 ) 248 (36 ) Input Input hpm12-1.p65, lw, jk 23