CROSS HYDRAULICS PTY LTD SECTION

Transcription

1 OVERVIEW The motor series is an economical alternative to more complex geroler designs that still provides high efficiency across a wide performance range. These motors are intended for medium-duty applications requiring high torque in a compact package and are suitable for industrial and mobile applications including car wash brushes, food processing equipment, conveyors, machine tools, agricultural equipment, sweepers, skid steer attachments, and more. KEY FETURES Variety of Mounts and Shafts provide flexibility in application design. High Pressure Shaft Seal offers superior seal life and performance. Spool Valve Design gives superior performance and smooth operation over a wide speed and torque range. uilt-in Check Valves (not shown) in the housing offers versatility and increased seal life. Integral Roller Stator Motor Design provides compact volume, high power & low weight. SPECIFICTIONS Peak Ratings - 1% of Operation Speed Flow Torque Pressure CODE Displacement rpm lpm [gpm] Nm [lb-in] bar [psi] cc [in 3 /rev] cont. inter. cont. inter. cont. inter. cont. inter. peak [1.5] [11] 45 [12] 35 [310] 48 [425] 100 [1450] 140 [2030] 225 [3260] [2.0] [13] 55 [15] 45 [398] 57 [504] 100 [1450] 140 [2030] 225 [3260] [2.5] [16] 70 [19] 65 [575] 74 [655] 100 [1450] 140 [2030] 225 [3260] [3.0] [16] 75 [20] 91 [805] 108 [956] 140 [2030] 175 [2540] 240 [3480] [3.6] [16] 75 [20] 125 [1106] 136 [1204] 160 [2320] 175 [2540] 240 [3480] [4.8] [16] 75 [20] 164 [1451] 183 [1620] 160 [2320] 175 [2540] 240 [3480] [5.9] [16] 75 [20] 195 [1726] 213 [1885] 160 [2320] 175 [2540] 240 [3480] [7.6] [16] 75 [20] 258 [2285] 278 [2460] 160 [2320] 175 [2540] 240 [3480] [9.4] [16] 75 [20] 321 [2840] 362 [3205] 160 [2320] 175 [2540] 240 [3480] [11.6] [16] 75 [20] 380 [3365] 420 [3720] 150 [2180] 175 [2540] 240 [3480] [14.6] [16] 75 [20] 445 [3940] 557 [4930] 140 [2030] 175 [2540] 240 [3480] [18.5] [16] 75 [20] 460 [4071] 602 [5330] 120 [1740] 160 [2320] 200 [2900] [23.7] [16] 75 [20] 488 [4320] 625 [5532] 95 [1380] 125 [1810] 180 [2610] CROSS HYDRULICS PTY LTD SECTION 10.14

2 PERFORMNCE 25 cc [1.5 in 3 /rev.] [4.0] 25 [6.6] 35 [9.2] 45 [11.9] 30 [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 9 [80] 18 [159] 25 [221] 32 [283] [88] [159] [230] [301] [80] [168] [230] [310] [71] [168] [221] [292] [62] [159] [230] [283] [53] [150] [221] [283] [44] [142] [212] [274] [44] [133] [195] [274] [115] [177] [248] [664] [690] 48 [425] [690] 44 [389] [681] 45 [398] [646] 45 [398] [602] 44 [389] [566] 43 [381] [513] 41 [363] [496] 39 [345] [106] 24 [211] 32 [282] 40 [352] 48 [423] 56 [493] 32 cc [2.0 in 3 /rev.] [4.0] 25 [6.6] 35 [9.2] 45 [11.9] 55 [14.5] 30 [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 11 [97] 24 [212] 35 [310] 37 [327] [106] [239] [327] [381] [97] [230] [319] [398] [88] [221] [310] [389] [80] [212] [301] [372] [71] [204] [283] [354] [62] [177] [257] [345] [62] [168] [239] [336] [53] [159] [230] [310] [44] [142] [212] [274] [106] [177] [248] [407] 56 [496] [425] 57 [504] [407] 56 [496] [398] 54 [478] [398] 52 [460] [381] 51 [451] [381] 50 [442] [372] 48 [425] [354] 46 [407] [301] 39 [345] [135] 31 [271] 41 [361] 51 [451] 61 [541] 71 [631] CROSS HYDRULICS PTY LTD SECTION 10.15

3 PERFORMNCE cc [2.5 in 3 /rev.] 30 [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 15 [133] 31 [274] 38 [336] 48 [425] [124] [274] [363] [478] [115] [283] [363] [469] [106] [265] [345] [451] [88] [239] [345] [451] [62] [221] [327] [434] [35] [204] [301] [407] [142] [265] [363] [496] [549] 70 [619] [575] 74 [655] [558] 74 [655] [540] 72 [637] [522] 71 [628] [496] 68 [602] [460] 64 [566] [168] 38 [336] 50 [442] 64 [566] 76 [673] 89 [788] [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 175 [2540] 50 cc [3.0 in 3 /rev.] 19 [168] 39 [345] 48 [425] [177] [336] [442] [159] [336] [460] [133] [327] [442] [106] [274] [398] [80] [239] [363] [53] [212] [327] [27] [150] [283] [133] [265] [549] [558] [566] [566] [522] [487] [469] [389] [354] [664] [690] [690] [681] [646] [602] [566] [513] [496] [814] [796] [788] [770] [743] [726] [708] [681] [903] 107 [947] [920] 108 [956] [912] 107 [947] [876] 106 [938] [867] 105 [929] [841] 102 [903] [823] 98 [867] [779] 93 [823] [212] 47 [416] 63 [558] 79 [699] 95 [841] 110 [973] 126 [1115] 138 [1221] CROSS HYDRULICS PTY LTD SECTION 10.16

4 PERFORMNCE [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 175 [2540] 59 cc [3.6 in 3 /rev.] 20 [177] 46 [407] 65 [575] 80 [708] 95 [841] 112 [991] [195] [416] [584] [717] [850] [1000] [177] [398] [566] [708] [823] [982] [150] [381] [549] [673] [788] [965] [124] [363] [513] [646] [770] [929] [88] [327] [487] [619] [743] [903] [62] [301] [460] [584] [726] [876] [35] [239] [416] [549] [673] [823] [195] [381] [513] [646] [761] [1106] 136 [1204] [1088] 134 [1186] [1071] 131 [1159] [1035] 127 [1124] [1000] 122 [1080] [965] 118 [1044] [920] 114 [1009] [885] 110 [973] [249] 56 [499] 75 [665] 94 [831] 113 [998] 132 [1164] 150 [1330] 164 [1455] [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 175 [2540] 78 cc [4.8 in 3 /rev.] 32 [283] 62 [549] 80 [708] 106 [938] 125 [1106] [274] [566] [743] [920] [1062] 142 [1257] [230] [531] [743] [903] [1106] [1274] [212] [496] [717] [885] [1080] [1257] [168] [469] [664] [850] [1044] [1239] [124] [407] [619] [814] [973] [1195] [88] [372] [584] [761] [938] [1133] [53] [319] [496] [690] [867] [1044] [27] [239] [442] [655] [814] [1000] [1434] 175 [1549] [1451] 183 [1619] [1416] 175 [1549] [1398] 170 [1504] [1381] 168 [1487] [1327] 164 [1451] [1239] 160 [1416] [1177] 148 [1310] [327] 75 [664] 100 [885] 125 [1106] 149 [1319] 174 [1540] 199 [1761] 218 [1929] CROSS HYDRULICS PTY LTD SECTION 10.17

5 PERFORMNCE [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 175 [2540] 96 cc [5.9 in 3 /rev.] 43 [381] 82 [726] 109 [965] 131 [1159] [381] [743] [956] [1177] 152 [1345] 180 [1593] [363] [699] [947] [1124] [1363] [1575] [345] [655] [894] [1115] [1345] [1558] [257] [558] [823] [1071] [1327] [1522] [177] [460] [752] [1018] [1310] [1496] [150] [469] [735] [982] [1221] [1460] [97] [372] [646] [823] [1115] [1407] [53] [310] [540] [788] [1044] [1283] [1743] [1770] 212 [1876] [1752] 213 [1885] [1726] 208 [1841] [1708] 203 [1796] [1619] 193 [1708] [1522] 183 [1619] [1381] 176 [1558] [407] 92 [814] 122 [1080] 153 [1354] 183 [1623] 214 [1894] 245 [2168] 268 [2372] [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 175 [2540] 125 cc [7.6 in 3 /rev.] 52 [460] 95 [841] 135 [1195] 168 [1487] [442] [867] [1221] [1522] 190 [1681] 234 [2071] [442] [850] [1168] [1487] [1788] [2088] [389] [814] [1115] [1451] [1752] [2053] [310] [726] [1044] [1416] [1708] [2000] [274] [681] [956] [1372] [1611] [1947] [133] [566] [858] [1292] [1469] [1858] [71] [442] [796] [1239] [1434] [1805] [354] [628] [1133] [1398] [1699] [2283] [2265] 278 [2460] [2319] 268 [2372] [2230] 266 [2354] [2106] 262 [2319] [1982] 256 [2265] [1850] 236 [2088] [1761] 224 [1982] [531] 119 [1053] 159 [1407] 199 [1761] 239 [2115] 279 [2469] 318 [2814] 348 [3080] CROSS HYDRULICS PTY LTD SECTION 10.18

6 PERFORMNCE [435] 60 [870] 80 [1160] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 175 [2540] 160 cc [9.4 in 3 /rev.] 56 [496] 112 [991] 154 [1363] 201 [1779] [513] [1018] [1381] [1814] 245 [2168] 285 [2522] [532] [1089] [1434] [1788] [2142] [2496] [443] [1035] [1389] [1743] [2106] [2460] [425] [1000] [1372] [1726] [2089] [2416] [283] [938] [1319] [1664] [2080] [2363] [204] [779] [1177] [1575] [1876] [2301] [142] [726] [1133] [1505] [1823] [2257] [89] [699] [1097] [1451] [1779] [2195] [2894] 360 [3186] [2850] 358 [3168] [2814] 355 [3142] [2770] 352 [3115] [2726] 342 [3027] [2673] 331 [2929] [2620] 319 [2823] [651] 147 [1302] 196 [1736] 245 [2170] 282 [2496] 343 [3038] 392 [3472] 429 [3798] [435] 60 [870] 80 [1160] 100 [1450] 115 [1670] 140 [2030] 150 [2180] 175 [2540] 190 cc [11.6 in 3 /rev.] 75 [664] 158 [1398] 200 [1770] 241 [2133] [690] [1416] [1805] [2230] [655] [1381] [1770] [2177] [619] [1345] [1735] [2124] [575] [1301] [1681] [2018] [478] [1257] [1593] [1965] [319] [1133] [1469] [1858] [133] [903] [1398] [1788] [832] [1292] [1717] [2575] 348 [3080] [2593] 354 [3133] [2566] 352 [3115] [2531] 340 [3009] [2451] 333 [2947] [2354] 322 [2850] [2248] 302 [2673] [2035] 290 [2566] [3336] [3363] 416 [3681] [3345] 420 [3717] [3327] 418 [3699] [3150] 402 [3558] [3097] 400 [3540] [2894] 376 [3327] [2805] 364 [3221] [803] 182 [1611] 242 [2142] 303 [2677] 348 [3079] 424 [3748] 454 [4016] 529 [4685] CROSS HYDRULICS PTY LTD SECTION 10.19

7 PERFORMNCE [435] 60 [870] 85 [1230] 100 [1450] 125 [1810] 140 [2030] 160 [2320] 175 [2540] 240 cc [14.6 in 3 /rev.] 89 [788] 194 [1717] 264 [2336] 326 [2885] [814] [1735] [2372] [2912] [796] [1699] [2336] [2841] [761] [1637] [2265] [2779] [726] [1584] [2195] [2699] [611] [1496] [2150] [2593] [425] [1345] [2035] [2496] [327] [1230] [1938] [2327] [230] [1133] [1814] [2168] [3487] [3513] 445 [3938] [3469] 439 [3855] [3398] 431 [3814] [3345] 421 [3726] [3221] 407 [3602] [3035] 386 [3416] [2903] 374 [3310] [4513] 554 [4903] [4442] 557 [4929] [4301] 545 [4823] [4204] 526 [4655] [4035] 508 [4496] [3903] 496 [4389] [3788] 481 [4257] [1018] 229 [2027] 325 [2875] 382 [3381] 478 [4230] 535 [4735] 611 [5407] 669 [5920] [435] 50 [725] 70 [1015] 85 [1230] 100 [1450] 120 [1740] 140 [2030] 160 [2320] 303 cc [18.5 in 3 /rev.] 123 [1089] 200 [1770] 282 [2496] 344 [3044] [1035] [1717] [2451] [3027] [991] [1735] [2434] [3009] [920] [1620] [2363] [2850] [761] [1487] [2230] [2690] [646] [1381] [2106] [2549] [531] [1239] [1974] [2390] [327] [1080] [1646] [2248] [204] [885] [1540] [2097] [3531] [3513] 460 [4071] [3452] 448 [3965] [3230] 440 [3894] [3098] 424 [3752] [2876] 396 [3505] [2735] 368 [3257] [2593] 359 [3177] Overall Efficiency % 40-59% 0-39% 526 [4655] 605 [5354] [4602] 602 [5328] [4558] 588 [5204] [4425] 571 [5053] [4248] 546 [4832] [4027] 527 [4664] [3929] 516 [4567] [1283] 241 [2133] 338 [2991] 410 [3628] 482 [4265] 579 [5124] 675 [5973] 772 [6832] CROSS HYDRULICS PTY LTD SECTION 10.20

8 PERFORMNCE [435] 45 [650] 55 [800] 65 [940] 80 [1160] 95 [1380] 110 [1595] 125 [1810] 388 cc [23.7 in 3 /rev.] 144 [1274] 220 [1947] 270 [2389] 338 [2991] [1292] [1973] [2407] [3009] [1283] [1938] [2381] [2347] [1221] [1903] [2319] [2850] [1062] [1805] [2212] [2743] [885] [1646] [2106] [2611] [673] [1469] [1965] [2496] [442] [1283] [1717] [2212] [372] [1195] [1558] [2000] [3646] 488 [4319] [3611] 484 [4283] [3558] 472 [4177] [3478] 458 [4053] [3310] 446 [3947] [3168] 427 [3779] [2956] 402 [3558] [2708] 373 [3301] [4850] [4832] 625 [5531] [4735] 618 [5469] [4602] 600 [5310] [4389] 576 [5097] [4177] 540 [4779] [3938] 520 [4602] [1640] 278 [2460] 340 [3007] 402 [3554] 494 [4374] 587 [5194] 680 [6014] 772 [6834] CROSS HYDRULICS PTY LTD SECTION 10.21

9 155 & 156 HOUSINGS (SE & MGNETO MOUNTS) Hole 1/2 NPT ligned Ports 2-Hole 1/2 SP.F ligned Ports* 58,7 [2.311] 11 2-Hole 7/8 O-Ring ligned Ports 68 Pilot Height: 8 [.31] 18 2-Hole 1/2 SP.F ligned Ports 80,8 [3.181] 45,7 [1.800] 90,8 [3.575] 131,9 [5.193] 102 [4.02] 43 [1.69]* NOTE: Dimension is found on page * dd 5 [.20] to dimension for the 10, 11, & 18 housings Hole 1/2 NPT ligned Ports ,7 [2.311] 31 4-Hole 7/8 O-Ring ligned Ports C8 Pilot Height: 8 [.31] C8 4-Hole 1/2 SP.F ligned Ports 45,7 [1.800] 90,8 [3.575] NOTE: Dimension is found on page * dd 5 [.20] to dimension for the 30 & 31 housings. 43 [1.69]* 12 2-Hole 1/2 SP.F Offset Ports 58,7 [2.311] 62 2-Hole 1/2 SP.F Offset Ports 62 & 69 Pilot Height: 8 [.31] 69 2-Hole 7/8 O-Ring Offset Ports 80,8 [3.181] 90,8 [3.575] 131,9 [5.193] 102 [4.02] 35 [1.38]* 36 [1.42] NOTE: Dimension is found on page * dd 5 [.20] to dimension for the 12 housing. CROSS HYDRULICS PTY LTD SECTION 10.22

10 155 & 156 HOUSINGS (SE & MGNETO MOUNTS) 32 4-Hole 1/2 SP.F Offset Ports ,7 [2.311] 90,8 [3.575] NOTE: Dimension is found on page [1.57] 36 [1.42] 17 2-Hole Manifold Ports G17 2-Hole Manifold Ports 55 [2.17] 14,3 [.562] 14,3 [.562] Spotface Ø 17,5 [.689] 2 [.079] Min. deep 80,8 [3.181] 63,5 [2,500] 45,7 [1.800] 90,8 [3.575] 131,9 [5.193] 102 [4.02] 14,3 [.562] 14,3 [.562] 50 [1.97] *(4) M8 x [.47] Min. deep NOTE: Dimension is found on page * The four (4) mounting holes on the 17 housing are 5/16-18 UN C at the same depth Hole Manifold Ports 55 [2.17] C7 4-Hole Manifold Ports C7 Pilot Height: 8 [.31] 14,3 [.562] 14,3 [.562] Spotface Ø 17,5 [.689] 2 [.079] Min. deep 63,5 [2,500] 45,7 [1.800] 90,8 [3.575] 14,3 [.562] 14,3 [.562] 45 [1.77]* NOTE: Dimension is found on page * Pilot height is for the 37 housing. ** dd 5 [.20] to dimension for the 37 housing. (4) M8 x [.47] Min. deep CROSS HYDRULICS PTY LTD SECTION 10.23

11 155 & 156 HOUSINGS (SE, MGNETO, 4-HOLE SQURE MOUNTS) 13 2-Hole 1/2 SP.F Offset Manifold Ports 55 [2.17] 63 2-Hole 1/2 SP.F Offset Manifold Ports 35 [1.38]* 63 Pilot Height: 8 [.31] 20 [.79] 20 [.79] 80,8 [3.181] 90,8 [3.575] 131,9 [5.193] 102 [4.02] 20 [.79] 20 [.79] 36 [1.42] NOTE: Dimension is found on page * dd 5 [.20] to dimension for the 13 housing. C3 4-Hole 1/2 SP.F Offset Manifold Ports [2.17] 3D 4-Hole 7/8 O-Ring Offset Manifold Ports 35 [1.38]* C3 Pilot Height: 8 [.31] 20 [.79] 20 [.79] 90,8 [3.575] 20 [.79] NOTE: Dimension is found on page * dd 5 [.20] to dimension for the 3D housing. 20 [.79] 36 [1.42] F30 4-Hole 1/2 NPT ligned Ports F31 4-Hole 7/8 O-Ring ligned Ports F38 4-Hole 1/2 SP.F ligned Ports 82,8 [3.260] 58,7 [2.311] *(4) M [.47] deep min. 22,9 [.902] 80,8 [3.181] Ø 44,4 [1.748] 90,8 [3.575] 22,9 [.902] 103,9 [4.091] Ø 82,55 [3.250] 48 [1.89] NOTE: Dimension is found on page * The four (4) mounting holes on the F30 & F31 housings are 3/8-16 UNC at the same depth. CROSS HYDRULICS PTY LTD SECTION 10.24

12 155 & 156 HOUSINGS (SE & MGNETO MOUNTS WITH RELIEF CVITY) F37 4-Hole Manifold Ports 82,8 [3.260] 55 [2.17] 14,3 [.56] 14,3 [.56] (4) M10 x [.47] Min. Deep 18,0 [.709] 80,8 [3.181] Ø 44,4 [1.748] 90,8 [3.575] 18,0 [.709] 103,9 [4.091] Ø 82,55 [3.250] 63,5 [2.50] 50 [1.97] (4) 5/16-18 UNC 12,0 [.47] Min. Deep NOTE: Dimension is found on page Hole 7/8 O-Ring Offset Ports 58,7 [2.311] 46,2 [1.819] 80,8 [3.181] 90,8 [3.575] 131,9 [5.193] 105,4 [4.150] NOTE: Dimension is found on page [1.58] 36 [1.42] 39 4-Hole 7/8 O-Ring Offset Ports C2 4-Hole 1/2 SP.F Offset Ports 40 [1.57] 58,7 [2.311] 39 Pilot Height: 41,2 [1.622]* 32,4 [1.276] 90,8 [3.575] C2 Pilot Height: 8 [.31] 35 [1.38]* 36 [1.42] NOTE: Dimension is found on page * dd 5 [.20] to dimension for the 39 housing. CROSS HYDRULICS PTY LTD SECTION 10.25

13 155 & 156 HOUSINGS (SE MOUNT WITH END PORTS) P6 P8 2-Hole 3/4 O-Ring Ports With 3mm Pilot 2-Hole 1/2 SP.F Ports With 3mm Pilot 2-Hole 3/4 O-Ring Ports With 8mm Pilot 2-Hole 1/2 SP.F Ports With 8mm Pilot 131,9 [5.193] LENGTH / WEIGHT CHRT 3mm Pilot Mounts - Dimension W Code mm [in] kg [lb] [5.55] 5.9 [13.0] [5.59] 6.0 [13.2] [5.63] 6.1 [13.4] [5.63] 6.1 [13.4] [5.71] 6.1 [13.4] [5.79] 6.2 [13.6] [6.91] 6.3 [13.9] [6.06] 6.4 [14.1] [6.22] 6.5 [14.3] [6.42] 6.7 [14.7] [6.69] 6.9 [15.2] [7.01] 7.2 [15.8] [7.44] 7.5 [16.5] NOTE: motor weights vary ± 0,5 kg [1 lb] depending upon motor configuration. 3,35 [.132] P6 & P8 Pilot Height: 8 [.31] W LENGTH / WEIGHT CHRT 8mm Pilot Mounts - Dimension W Code mm [in] kg [lb] [5.35] 5.8 [12.1] [5.39] 5.9 [13.0] [5.43] 6.0 [13.2] [5.43] 6.0 [13.2] [5.51] 6.0 [13.2] [5.59] 6.1 [13.4] [5.71] 6.2 [13.6] [5.87] 6.3 [13.9] [6.02] 6.4 [14.1] [6.22] 6.6 [14.5] [6.50] 6.8 [15.0] [6.81] 7.1 [15.6] [7.24] 7.4 [16.3] NOTE: motor weights vary ± 0,5 kg [1 lb] depending upon motor configuration. 96,6 [3.803] 62,4 [2.457] 31,2 [1.228] 7,1 [.280] CROSS HYDRULICS PTY LTD SECTION 10.26

14 155 & 156 HOUSINGS (4 HOLE SQURE MOUNT WITH END PORTS) F21 F26 G24 G28 4-Hole 7/8 O-Ring Ports 4-Hole 3/4 O-Ring Ports 4-Hole M22 x 1.5 Ports 4-Hole 1/2 SP.F Ports Ø82,5 [3.248] 82 [3.228] F21 & F28 (4) 3/8-16 UNC G24 & G28 (4) M [3.228] LENGTH / WEIGHT CHRT Dimension Z Code mm [in] kg [lb] [5.55] 5.5 [12.1] [5.59] 5.6 [12.3] [5.63] 5.7 [12.6] [5.63] 5.7 [12.6] [5.71] 5.7 [12.6] [5.79] 5.8 [12.8] [6.91] 5.9 [13.0] [6.06] 6.0 [13.2] [6.22] 6.1 [13.4] [6.42] 6.3 [13.9] [6.69] 6.5 [14.3] [7.01] 6.8 [15.0] [7.44] 7.1 [15.7] NOTE: motor weights vary ± 0,5 kg [1 lb] depending upon motor configuration. 44,4 [1.748] Z 3,35 [.132] 96,6 [3.803] 31,2 [1.228] 62,4 [2.457] 7,1 [.280] CROSS HYDRULICS PTY LTD SECTION 10.27

15 155 & 156 TECHNICL INFORMTION PERMISSILE SHFT SEL PRESSURE The curve below represents allowable seal pressure at various speeds. Operation in the gray area results in maintaining the rated life of the shaft seal. ctual shaft seal pressure depends on motor configuration (see below). 276 [4000] 207 [3000] 138 [2000] 69 [1000] bar [psi] Intermittent Continuous rpm With check valves and drain connection, the shaft seal pressure equals pressure in the drain line. With check valves and no drain connection, shaft seal pressure is identical to output pressure. No check valves and no drain connection, the shaft seal pressure is identical to the average value of input and output pressure. LLOWLE SHFT LOD / ERING CURVE The bearing curve below represents the side load capacity of the motor at the centerline of the key for various motor speeds. Operating conditions within the shaded area will maintain acceptable oil film lubrication with recommended fluids. Operating conditions outside the shaded area are susceptible to motor failure due to oil starvation and/or excessive heat generation. Fluids with low lubricity or low viscosity may require the maximum load and speed ratings to be derated to provide acceptable motor life and performance [1800] 6000 [1350] 4000 [900] 2000 [450] LENGTH / WEIGHT CHRT 3mm Pilot Mounts - Dimension Code mm [in] kg [lb] [5.24] 6.3 [13.9] [5.28] 6.4 [14.1] [5.34] 6.5 [14.2] [5.34] 6.5 [14.2] [5.40] 6.5 [14.3] [5.49] 6.6 [14.5] [5.59] 6.7 [14.7] [5.74] 6.8 [14.9] [5.90] 6.9 [15.2] [6.10] 7.1 [15.6] [6.36] 7.3 [16.1] [6.69] 7.6 [16.7] [7.13] 7.9 [17.5] NOTE: motor weights vary ± 0,5 kg [1 lb] depending upon motor configuration. LENGTH / WEIGHT CHRT 8mm Pilot Mounts - Dimension Code mm [in] kg [lb] [5.04] 6.2 [13.6] [5.08] 6.3 [13.9] [5.16] 6.4 [14.1] [5.16] 6.4 [14.1] [5.20] 6.4 [14.1] [5.28] 6.5 [14.3] [5.39] 6.6 [14.5] [5.55] 6.7 [14.7] [5.71] 6.8 [15.0] [5.91] 7.0 [15.4] [6.18] 7.2 [15.8] [6.50] 7.5 [16.5] [6.93] 7.8 [17.2] NOTE: motor weights vary ± 0,5 kg [1 lb] depending upon motor configuration. N [lbf] rpm THRUST LOD 445 DaN [1000 lbs] 445 DaN [1000 lbs] CROSS HYDRULICS PTY LTD SECTION 10.28

16 155 & 156 SHFTS 10 1 Straight 15 1 Straight Extended 02 6 Spline (1/4 UNC Tap) 04 6 Spline (M8 x 1.25 Tap) Torque: 655 Nm [5800 lb-in] Torque: 429 Nm [3800 lb-in] 6,35 [.250] 6,3 [.248] 5 [.20] H 31,75 [1.250] 31,45 [1.238] Mounting Flange 25,4 [1.000] H Mounting Flange 28,15 [1.122] 27,95 [1.100] 6,35 [.250] 6,3 [.248] 25,4 [1.000] 25,4 [0.999] Ø25,4 [1.000] Ø25,4 [.999] 1/4-20 UNC-2 16 [.63] Min. deep 05 1 Pinhole 9,5 [.375] 66 1 Pinhole 8,0 [.315] Torque: 678 Nm [6000 lb-in] 53 1 Pinhole 10,3 [.406] *16 [.62] H Mounting Flange 1 1 Straight with Woodruff Key Torque: 655 Nm [5800 lb-in] 6,38 [.251] 6,35 [.250] Ø25,4 [1.000] Ø25,1 [.990] H Mounting Flange 19,1 [.761] 18,0 [.709] 25,4 [1.000] 25,4 [0.999] 28,30 [1.114] 27,89 [1.098] Ø25,4 [1.000] Ø25,4 [.999] 1/4-20 UNC-2 16 [.63] Min. deep 1/4-20 UNC-2 16 [.630] Min. NOTE: *For 66 shaft subtract 4,6 [.18] from this dimension mm Straight 16 25mm Straight Extended Tooth Spline Torque: 678 Nm [6000 lb-in] 8,00 [.315] 7,98 [.314] 7,00 [.276] 6,91 [.272] 5 [.20] H Mounting Flange 32,0 [1.260] 31,4 [1.235] Torque: 170 Nm [1500 lb-in] 15,5 [.610] H Mounting Flange 28,00 [1.102] 27,71 [1.091] Ø25,02 [.985] Ø25,00 [.984] Ø22,3 [.876] Ø22,2 [.874] M [.79] Min. 1/4-20 UNC-2 16 [.63] Min. MOUNTING FLNGE TO SHFT END Dimension H Code 8mm Pilot Code 8mm Pilot 01 48,3 [1.902] 15 67,1 [2.642] 02 50,3 [1.980] 16 67,6 [2.661] 04 50,3 [1.980] 53 50,3 [1.980] 05 50,3 [1.980] 66 55,3 [2.177] 10 50,3 [1.980] 1 50,3 [1.980] 12 55,3 [2.177] NOTE: For 3mm pilot housings subtract 5,0 [.197] from dimension. Shaft lengths vary ± 0,8 [.030]. CROSS HYDRULICS PTY LTD SECTION 10.29

17 155 & 156 MODEL CODE UILDER DISPLCEMENT HOUSING SHFT PINT CVITY DD ON MISCELLNEOUS STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 1 - Select a series STEP 3 (Continued) - Select a housing option 155 Clockwise Rotation STEP 2 - Select a displacement option STEP 3 - Select a housing option P6 P cc [1.5 in3/rev] 32 cc [2.0 in3/rev] 40 cc [2.5 in3/rev] 50 cc [3.0 in3/rev] 59 cc [3.6 in3/rev] 78 cc [4.8 in3/rev] 96 cc [5.9 in3/rev] 156 Counterclockwise Rotation cc [7.6 in3/rev] 154 cc [9.4 in3/rev] 190 cc [11.6 in3/rev] 240 cc [14.6 in3/rev] 303 cc [18.5 in3/rev] 388 cc [23.7 in3/rev] 2-Hole 3/4" O-Ring With End Ports (S) 2-Hole 1/2" SP.F With End Ports (S) 2-Hole 3/4" O-Ring With End Ports 8mm Pilot 2-Hole 1/2" SP.F With End Ports 8mm Pilot 2-Hole 1/2" NPT ligned Ports (S) 2-Hole 7/8" O-ring ligned Ports (S) 2-Hole 1/2" SP.F Offset Ports (S) 2-Hole1/2" SP.F Offset Manifold (S) 2-Hole Manifold Ports (S) NOTE: To obtain the desired direction of shaft rotation, use the graphic above to determine the rotation code for the motor D C2 C3 C7 C8 F21 F26 F30 F31 F37 F38 G17 G24 G28 2-Hole 1/2" SP.F ligned (S) 2-Hole 7/8" O-ring With Valve Cavity (S) 4-Hole 1/2" NPT ligned Ports 4-Hole 7/8" O-ring ligned Ports 4-Hole 1/2" SP.F Offset Ports 4-Hole Manifold Ports 4-Hole 7/8" O-ring With Valve Cavity 4-Hole 7/8" O-ring Offset Manifold Ports 2-Hole 1/2" SP.F Offset 8mm Pilot 2-Hole 1/2" SP.F Offset Manifold 8mm Pilot 2-Hole 1/2" SP.F ligned 8mm Pilot 2-Hole 7/8 O-Ring Offset Ports 8mm Pilot 4-Hole 1/2 SP.F Offset Ports 8mm Pilot Valve Cavity 4-Hole 1/2 SP.F Offset Manifold 8mm Pilot 4-Hole Manifold Ports 8mm Pilot 4-Hole 1/2 SP.F ligned Ports 8mm Pilot 4-Hole 7/8" O-ring With End Ports (S) 4-Hole 3/4" O-ring With End Ports (S) 4-Hole 1/2" NPT ligned Ports (S) 4-Hole 7/8" O-ring ligned Ports (S) 4-Hole Manifold Ports (S) 4-Hole 1/2 SP.F ligned Ports (S) 2-Hole Manifold Ports (S) 4-Hole M22 x 1.5 With End Ports (S) 4-Hole 1/2" SP.F With End Ports (S) CROSS HYDRULICS PTY LTD SECTION 10.30

18 155 & 156 MODEL CODE UILDER DISPLCEMENT HOUSING SHFT PINT CVITY DD ON MISCELLNEOUS STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 STEP 7 STEP 8 STEP 4 - Select a shaft option Tooth Spline 6 (1/4 UNC Tap) 6 (M8 x 1.25 Tap) 1 Pinhole (.375 ) 1 Straight 25mm Straight STEP 5 - Select a paint option lack Straight Ext. (S) 25mm Straight Ext. (S) 1 Pinhole (.406 ) 1 Pinhole (8mm) 1 Straight (Woodruff Key) STEP 6 - Select a valve cavity option and installed valve C D E None Relief Valve Cavity 69 bar [1000 psi] 86 bar [1250 psi] 104 bar [1500 psi] 121 bar [1750 psi] 138 bar [2000 psi] 173 bar [2500 psi] 207 bar [3000 psi] NOTE: Valve cavity is only available on the 19, 39, 62 & C2 housings. The option will not have a valve cartridge listed above installed. F G J L lack (Unpainted Flange) STEP 7 - Select an add on option C W Y Z STEP 8 - Select a miscellaneous option C F Standard Lock Nut Solid Hex Nut 4-Pin Dual Male Weatherpack Connector (S) 4-Pin M12 Dual Male Connector (S) 3-Pin Single Male Weatherpack Connector (S) 4-Pin M12 Single Male Connector (S) NOTE: (S) - STEP 3 Housings available for use with speed sensors. STEP 4 Shafts available for use with speed sensors. STEP 7 Speed sensor options. None Freeturning Rotor No Check Valves Installed In Motor CROSS HYDRULICS PTY LTD SECTION 10.31