Disc Valve Hydraulic Motors Series 4000

Transcription

1 Disc Valve Hydraulic Motors Series inspired hydraulics. Änderungen und Druckfehler vorbehalten EN EATON_Motoren english

2 Highlights Features 10 displacements, a variety of mounting flanges and output shafts Reliable, proven design High efficiency Environmental protection options Benefits Flexiblilty in designing this motor into a system Options that fit well into tough applications Applications Mowing Snow Removal Sprayer Trencher Wood Products Description The offers up to in-lb of torque and 25 gpm (continuous ratings). This is the corner stone of the Char-Lynn line. Mowing Motors Geroler Element Flow l/min [GPM] Speed RPM Pressure bar [PSI] Torque Nm [lb-in] 10 Displacements [25] Continuous** 0 [40] Intermittent* 722 Cont.** 6 Inter.* 200 [00] Cont.** 0 [00] Inter.* 9 [] Cont.** 0 [100] Inter.* ** Continuous (Cont.) Continuous rating, motor may be run continuously at these ratings * Intermittent (Inter.) Intermittent operation, 10% of every minute. Snow Removal Sprayer Trencher Fon: +49 (0) Fax: +49 (0)

3 Specifications 0 SERIES MOTORS Displ. cm 3 /r [in3/r] 0 [ 6.7] 1 [ 7.9] 160 [ 9.9] 205 [12.5] 2 [.0] 20 [.1] 310 [19.0] 3 [24.0] 4 [.0] 625 [.0] Speed Continuous (RPM) Intermittent Flow Flow Continuous 75 [20] [25] [25] [25] [25] [25] [25] [25] [25] [25] l/min [GPM] Intermittent [25] 1 [] 1 [] 1 [] 1 [] 1 [] 1 [] 0 [40] 0 [40] 0 [40]. Torque* Continuous 320 [250] 375 [33] 45 [42] [50] 5 [6240] 7 [6666] 50 [75] 9 [ 240] 9 [ 375] 9 [ 605] Nm [lb-in] Intermittent 4 [4160] 560 [4940] 5 [6240] 00 [7100] [74] 7 [471] 1065 [9420] 5 [104] [100] 0 [100] Pressure Continuous 205 [00] 205 [00] 205 [00] 205 [00] 205 [00] 205 [00] 205 [00] 1 [2750] 0 [2000] 1 [10] bar Intermittent 310 [00] 310 [00] 310 [00] 260 [3750] 310 [00] 260 [3750] 260 [3750] 240 [00] 1 [2500] 0 [2000] [ PSI] Peak 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 310 [00] 2 [4250] 0 [30] 10 [2] Weight Standard or.9 [39.5] 1.1 [40.0] 1.1 [40.0] 1.4 [40.5] 1.6 [41.0] 19.1 [42.0] 19.5 [43.0] 20.4 [.0] 21. [4.0].1 [51.0] kg [lb] Wheel Mount Bearingless.1 [31.0].3 [31.5].1 [31.0].5 [32.0].7 [32.5].2 [33.5].6 [34.5] 16.6 [36.5].9 [39.5] 19.3 [ [42.5] Maximum Case Pressure: See case pressure seal limitation graph. *See shaft torque ratings for limitations.. Note: To assure best motor life, run motor for approximately one hour at % of rated pressure before application to full load. Be sure motor is filled with fluid prior to any load applications. Maximum Inlet Pressure: 310 bar [00 PSI] Do not exceed pressure rating (see chart above). Maximum Return Pressure: 310 bar [00 PSI] with case drain line installed. Do not exceed pressure rating (see chart above). bar [ PSI] : The true pressure difference between inlet port and outlet port Continuous Rating: Motor may be run continuously at these ratings Intermittent Operation: 10% of every minute Peak Operation: 1% of every minute Recommended Fluids: Premium quality, anti-wear type hydraulic oil with a viscosity of not less than SUS at operating temperature. Recommended Maximum System Operating Temp.: 2 C [10 F] Recommended Filtration: per ISO Cleanliness Code, 4406: 20/1/13 Fon: +49 (0) Fax: +49 (0)

4 160 cm 3 /r [9.9 in 3 /r] Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 Continuous Intermittent [250] [] [410] [420] 36 [4] [4] [410] 4 [3] 12 [0] 40 2 [3] 256 [2] 291 [2] 329 [0] [1] [0] 9 [500] [10] 5 [00] cm 3 /r [12.5 in 3 /r] [00] Peak No Operation [2000] 0 [2500] [00] [00] [0] [] [] [2220] [260] [60] [60] [] [50] [160] [2410] [30] [4060] [] [5420] [0] [] [] [25] [3410] [4260] [5040] [57] [6340] [0] [100] [2620] [] [43] [51] [50] [65] [] [120] [2660] [60] [4410] [5240] [6020] [60] [120] [20] [0] [4460] [50] [10] [50] [0] [26] [] [4440] [50] [40] [] [26] [60] [44] [52] [20] [] [2650] [40] [4410] [520] [10] [50] [2640] [20] [4] [52] [00] [] [2620] [10] [40] [52] [70] [16] [2] [00] [43] [750] [1640] [2560] [340] [4360] [710] [40] [2510] [] [41] [5260] 5 36 [5240] [50] [20] 6 15 [20] [20] 6 2 [20] 6 27 [20] [5510] [67] [6] 70 3 [00] 310 [6210] 0 [6740] 0 [7100] Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 [250] [500] [00] [2000] 0 [2500] [00] [00] [0] [00] [0] [60] [1320] [2050] [2750] [4410] [40] [0] [10] [20] [270] [30] [3940] [0] [1360] [200] [27] [3340] [39] [] [50] [320] [3] 46 [320] 93 [0] 137 [20] 14 [260] 2 [240] [220] [200] [10] [0] 460 [] 509 [] [710] [00] [2100] [220] [3420] [4020] [4620] [5220] [710] [20] [20] [250] [10] [410] [40] [40] [720] [10] [210] [20] [60] [40] [450] [54] [720] [0] [2220] [20] [30] [42] [4920] [5560] [0] [10] [21] [2920] [] [420] [4920] [55] [60] [20] [2160] [2] [] [42] [4920] [550] [6] [00] [21] [260] [50] [4260] [4920] [55] [650] [1360] [2100] [2] [] [4250] [4910] [5] [6] [1340] [20] [200] [10] [4240] [4910] [620] [13] [2060] [27] [00] [4220] [4910] [] [1320] [2050] [270] [340] [4210] [40] [560] [120] [19] [20] [34] [39] [4640] [19] Torque [lb-in] } Nm 675 Speed RPM [50] [5] [55] [55] 6 13 [57] 6 [5] [6010] [60] 6 2 [0] 0 12 [6200] [6220] [6240] 5 2 Fon: +49 (0) Fax: +49 (0)

5 5 Fon: +49 (0) Fax: +49 (0) >> [510] 60 [10] 1 [60] 5 60 [200] 2 60 [2] 2 59 [31] 5 59 [510] [1040] [] 5 [2100] 2 9 [2620] 2 [3160] 5 [500] [1020] [60] 5 [20] [26] 2 [] [40] 5 0 [2100] 2 [2620] 2 [] 5 7 [250] [500] [750] 50 [1250] 5 [00] [4] [6] [] [10] Pressure Bar [PSI] 2 cm 3 /r [.0 in 3 /r] [36] [3660] 4 6 [360] 4 1 [36] 4 1 [50] [460] 50 5 [90] 0 2 [40] 55 [9] 0 [] 1 [19] 13 [240] [29] 3 12 [500] 55 1 [20] 1 29 [2040] 0 29 [2540] 25 2 [50] 3 27 [.5] 1,9 [1] 3, [2] 7,5 [3] 5 12 [3420] 5 26 [41] [4200] 3 [4210] 3 [40] 40 3 [2000] 0 [] 4 [39] 4 24 Flow LPM [GPM] Torque [lb-in] Nm } Speed RPM [46] 525 [4710] 5 0 [0] 5 [4440] 500 [5] [90] 0 12 [] 5 10 [200] 2 9 [20] 2 [30] 5 [12] [360] 4 1 [2500] 1 [960] [20] 1 2 [2060] [2] [31] 5 20 [] [36] [0] 243 [00] [2040] [250] [3] 5 9 [16] [3660] 4 6 [9] 274 [0] [2020] [2560] 2 2 [30] [1] 6 [3650] [910] 5 [60] [2000] 3 [2550] 2 2 [3100] 0 0 [20] [] [20] [19] 334 [2500] [50] 3 3 [22] 3 [20] 2 [10] 5 1 [19] [2460] [290] 3 3 [25] [1250] 0 6 [160] [] 1 [4] 55 2 [0] [420] 213 [] 244 [0] 275 [0] 40 5 [310] 337 [4250] 40 [40] [5220] 5 75 [260] 3 [60] 75 7 [] 2 3 [20] 3 0 [3640] [4740] 5 1 [47] [4220] 3 [4200] 203 [41] 2 [410] [] [40] 372 [34] 3 4 [41] [10] [40] 1 1 [] 132 [22] [27] [3340] [3340] [40] [4640] [3960] [4460] [510] 55 7 [40] [3910] [4] [40] [460] [5200] [560] [4710] [50] [5720] 6 24 [40] 5 2 [5220] 5 23 [5710] 6 2 [6200] [2750] 1 [00] 205 [3250] [00] 240 [3750] 260 [460] 5 10 [5020] [5250] [52] 137 [55] 6 47 [56] 6 72 [5720] [60] [60] 6 [6200] 0 99 [20] 20 [5740] [640] 7 42 [6620] [66] [60] 6 16 [6] [50] 7 63 [6640] 750 [7340] 36 [] 10 [74] [] [74] 7 [50] [6240] [6710] [70] 05 [40] [520] [5750] [60] 5 7 [60] [4740] [5260] 5 1 [5740] [6220] 5 15 [47] [5250] 5 [57] [6210] [579] 65 [67] 132 [74] [2962] 3 51 [57] [4139] [53] [17] [] [297] 3 77 [3601] [4193] 474 [573] [167] [2404] 272 [07] [30] [421] [16] [] [2997] [3629] [4] [250] [500] [750] 50 [1250] 5 [00] [4] [6] [] [10] Pressure Bar [PSI] 20 cm 3 /r [.1 in 3 /r] [4712] 2 49 [4793] [412] [437] [50] [3] 60 4 [1074] [5] [36] [227] 25 [241] 321 [3394] 4 [6] [56] [16] 1 26 [2] [22] [34] [] 447 [.5] 1,9 [1] 3, [2] 7,5 [49] [24] 5 22 [525] [] [54] 1 99 [5442] [2000] 0 [4] 5 10 [2922] 3 21 Flow LPM [GPM] [0] 5 [63] [26] [69] 26 [2991] 3 7 [3609] 40 7 [422] 47 6 [12] [432] [2500] 1 [06] [44] [2972] [5] [4213] 4 12 [] [416] [1096] [24] [2947] [65] [4203] 20 [16] [1075] [2299] [29] 3 7 [41] 6 [41] [1] 6 [5] [2274] [29] [21] [4] [20] [1005] 1 2 [7] [256] [340] [4136] [25] [940] [21] [225] [3419] [406] [] 1 [21] 243 [2759] [] 132 [26] [547] [527] 60 1 [497] [472] 2 [437] [402] 26 [366] [66] [6666] 7 [7191] 13 [7749] [3] [5] [313] [332] [3] [394] [4] [401] [4791] [6] 7 25 [5441] 6 2 [22] 3 [1] [] [2057] [71] [1] [0] 201 [15] [] [40] [] [] 1 16 [] [16] [1669] [1629] 14 2 [] 9 3 [0] [134] 2 46 [4710] [54] 6 [6521] [6946] [36] [2750] 1 [00] 205 [3250] [00] 240 [3750] 260 [6] 7 6 [79] 1 5 [54] 65 4 [7502] 4 41 [020] 6 40 [471] 7 [2] [07] [097] 9 64 [6556] [22] [6601] [22] [751] 49 [751] 49 1 [6940] 74 1 [6940] [656] [54] 6 [56] [600] 65 [59] [5994] [60] [6034] 62 [65] [6436] [6362] [602] 61 4 [5919] [5919] [551] [5420] [5] [94] [5205] [5205] 5 3 [44] [73] 5 9 [5021] Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Continuous Intermittent Peak No Operation

6 Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 [] 132 [40] 1 Continuous Intermittent [250] [500] [750] 50 3 cm 3 /r [24.0 in 3 /r] Peak No Operation [1250] 5 [00] [50] [2000] [0] [2500] [0] [1340] [750] [] [20] [27] [3460] [41] [4] [50] [6310] [10] [70] [00] [00] [22] [] [50] [4620] [10] [0] [6750] [74] [240] [9] [60] [16] [24] [3310] [4] [40] [5640] [63] [71] [7] [70] [60] [16] [2540] [3410] [410] [490] [570] [650] [7] [220] [40] [160] [2550] [3] [4260] [50] [5] [6650] [00] [160] [2550] [3] [4260] [5100] [5920] [67] [0] [1660] [2520] [30] [42] [50] [50] [740] [1640] [24] [33] [4260] [5100] [50] [710] [1620] [2460] [] [4240] [500] [540] [60] [1] [24] [3340] [4220] [5060] [510] [0] [0] [2] [3320] [4210] [5040] [570] [5] [] [40] [3220] [4160] [5010] [4] [10] [0] [0] [40] [4960] [100] [1650] [22] [20] [50] [20] [2] [2] [30] [2050] [27] [3620] [5740] [50] 6 0 [66] 755 [6650] [740] 66 [7560] 55 4 Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [22] 3 [25] [] 1 [] 132 [2750] 1 [640] [12] [1960] [2640] [32] [3940] [4] [5240] [50] [6510] [] [77] [0] [9100] [650] [10] [19] [2660] [3320] [0] [460] [] [] [66] [720] [7940] [640] [10] [190] [26] [] [40] [4710] [60] [6020] [66] [620] [120] [19] [2660] [3340] [40] [4740] [] [6050] [6710] [00] [3250] 205 [00] 240 [97] [104] cm 3 /r [19.0 in 3 /r] [250] [500] [750] 50 [1250] 5 [00] [50] [2000] [0] [2500] [2750] [00] 205 [3250] [00] 240 [3750] 260 [] [10] [620] [12] [1920] [2560] [31] [370] [42] [40] [54] [600] [66] [72] [70] [4] [0] [6] [120] [1940] [25] [] [] [40] [50] [560] [60] [6910] [75] [160] [7] [9420] [] [1260] [1940] [26] [3340] [4040] [47] [] [6060] [5] [1240] [1920] [2] [3310] [0] [4710] [0] [6060] [540] [10] [10] [250] [320] [39] [40] [0] [6050] [4] [1210] [10] [2550] [3240] [39] [460] [] [6040] [0] [] [160] [2520] [3210] [30] [46] [60] [60] [420] [] [120] [2520] [310] [] [4640] [340] [0] [0] [2510] [3160] [20] [] [1010] [10] [2420] [3100] [3720] [00] [0] [60] [20] [40] [43] [43] Torque [lb-in] 4} Nm 413 Speed RPM [20] 25 [520] [50] 50 1 [6720] 0 1 [67] 0 9 [7320] 25 [73] 109 Fon: +49 (0) Fax: +49 (0)

7 4 cm 3 /r [.0 in 3 /r] Performance Data Motors run with high efficiency in all areas designated with a number for torque and speed. For best motor life select a motor to run with a torque and speed range shown in the light shaded area. Performance data is typical at SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [250] [500] [750] cm 3 /r [.0 in 3 /r] [1250] 5 [00] [1] [100] [40] [3] [450] [00] [] [720] [2] [0] [105] [0] [3675] [5010] [60] [25] [1] [605] [] [10] [2420] [3750] [55] [6] [70] [410] [00] [] [10] [2460] [25] [5220] [6620] [] [4] [910] [94] [00] [2500] [30] [52] [6640] [79] [460] [] [2550] [3975] [20] [66] [0] [5] [60] [2] [4050] [75] [60] [100] [] [1] [25] [3965] [25] [665] [065] [16] [0] [2465] [0] [5275] [66] [0] [1] [9] [2405] [25] [5240] [6655] [73] [20] [25] [] 1 [] 132 [40] 1 Continuous Intermittent Peak No Operation [9] [20] [37] [5205] [6640] [750] [25] [3] [5000] [6] [550] [1975] [3] [] [6200] [3125] [] [250] [42] [660] [620] 975 [50] 9 [10] 1 [925] [] [100] 125 [2000] 0 [10075] 10 7 [100] 0 Flow LPM [GPM] [.5] 1,9 [1] 3, [2] 7,5 [4] [6] [] [10] [12] [] [16] [1] 6 [20] [25] [] 1 [] 132 [40] 1 [250] [500] [750] 50 [1250] 5 [00] [50] [2000] [0] 0 5 [00] [50] [0] [175] [275] [25] [4775] [5720] [66] [00] [90] [5] [1940] [2975] [39] [5010] [6010] [10] [000] [9] [2005] [75] [4160] [52] [60] [75] [375] [9] [100] [920] [2010] [3100] [415] [5265] [63] [7420] [4] [9465] [5] [20] [3125] [4205] [52] [65] [745] [0] [19] [] [4205] [52] [63] [740] [60] [1975] [] [4200] [55] [63] [7] [] [19] [55] [4165] [5275] [6360] [74] [05] [1910] [20] [41] [52] [63] [7420] [740] [160] [290] [4] [52] [65] [70] [60] [0] [2940] [405] [5] [625] [5] [1665] [200] [5] [5210] [] [20] [26] [35] [45] [595] [2] [10] [25] [3260] [250] Torque [lb-in] 320} Nm 241 Speed RPM [510] [525] [2500] 1 Fon: +49 (0) Fax: +49 (0)

8 Dimensions Standard Mount Standard Mount Ports 1 1/16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 3/4 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW Port B Port B YY XX Y X 22,4/21, [./.6] 127,0 [5.00] Dia. Bolt Circle 101,60/101,47 [4.000/3.9] Dia. 9,9 [4.72] Max, Square 4 Bolt 3/4 Inch Case Drain Port Split Flange Ports SAE C Flange Add 4,3 [.] to X and Y Dim. (see Chart) Flange Comparison SAE B/ SAE C 26,7/26.2 [1.05/1.03] 4,3/3,3 [./.13] 10,7/9,1 [.42/.36] 12,7/12,4 [.50/.49] 127,00/126,7 [5.000/4.9] Pilot Dia.,3 [5.4] Square 9,0 [3.6] Square,2/,5 [.60/.57] (4),/, [.572/.557] Dia. Thru 1,92 [6.375] Dia. B.C.,2/63,5 [3.00/2.50] STANDARD MOUNT MOTOR DIMENSIONS Displacement X Y XX YY cm 3 /r [in 3 /r] mm [inch] mm [inch] mm [inch] mm [inch] 0 [ 6.7],3 [6.] 2,4 [.44] 167,3 [6.59] 246,3 [ 9.] 1 [ 7.9] 162,3 [6.39] 21,4 [.60] 1,3 [6.75] 250,4 [ 9.6] 160 [ 9.9] 16,7 [6.64] 224,7 [.5] 7,7 [7.00] 256,7 [10.] 205 [12.5] 7,2 [6.9] 3,2 [ 9.1] 16,2 [7.33] 265,2 [10.44] 2 [.0] 16,7 [6.64] 224,7 [.5] 7,7 [7.00] 256,7 [10.] 310 [19.0] 7,2 [6.9] 3,2 [ 9.1] 16,2 [7.33] 265,2 [10.44] 3 [24.0] 17,9 [7.40] 243,9 [ 9.60] 196,9 [7.75] 275,9 [10.6] 4 [.0] 200,7 [7.] 256, [10.] 209,7 [.26] 2, [.37] 625 [.0] 2, [.5] 273,9 [10.7] 226,7 [.93] 5,9 [12.04] Fon: +49 (0) Fax: +49 (0)

9 Dimensions Wheel Mount Wheel Mount Ports 1 1/16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 3/4 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW YY Port B XX Port B Y X 21,/21,3 [.6/.4] 4 Bolt 3/4 inch Split Flange Ports Case Drain Port 1, [3.22] 9,7/,6 [./.34] 139,/139,57 [5.500/5.4] Dia. 10,7 [4.2] Dia. Case Drain Port 6,74 [4.596] Square,/, [.572/.557] Thru (4), [5.6] Square 124,2 [4.9] 165,0 [6.50] Dia. Bolt Circle WHEEL MOUNT MOTOR DIMENSIONS Displacement X Y XX YY cm 3 /r [in 3 /r] mm [inch] mm [inch] mm [inch] mm [inch] 0 [ 6.7] 7,5 [3.] 3,3 [5.64] 96,4 [3.0] 5,3 [6.] 1 [ 7.9] 91,6 [3.] 7,3 [5.0] 100,5 [3.96] 9,3 [7.06] 160 [ 9.9] 97, [3.5] 3,7 [6.05] 106, [4.21] 15,7 [7.31] 205 [12.5] 106,4 [4.19] 162,3 [6.39] 1,4 [4.55] 194,3 [7.65] 2 [.0] 97, [3.5] 3,7 [6.05] 106, [4.21] 15,7 [7.31] 310 [19.0] 106,4 [4.19] 162,3 [6.39] 1,4 [4.55] 194,3 [7.65] 3 [24.0] 1,1 [4.] 3,0 [6.1] 126,1 [4.97] 205,0 [.07] 4 [.0] 129,9 [5.12] 15,7 [7.31] 1, [5.47] 2,7 [.57] 625 [.0] 6,9 [5.79] 202,9 [7.99] 6,0 [6.] 2,0 [9.25] Fon: +49 (0) Fax: +49 (0)

10 Dimensions Bearlingless Bearingless Ports 1 1/16-12 UN-2B SAE O-ring Staggered Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or 4 Bolt 3/4 inch Split Flange Ports (2) 7/16-20 UNF-2B SAE O-ring Case Drain Port (1) or G 3/4 (BSP) Staggered Ports (2) G 1/4 (BSP) Case Drain Port (1) Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW YY Port B XX Port B Y X 1,9 [6.375] Bolt Circle.50/, [.572/.557] 127,0/126,9 [5.000/4.9] Dia. 1,5 [4.50] Square 4 Bolt 3/4 inch Split Flange Ports For Bearingless Motor application information contact your Eaton representative (mating coupling blanks available from Eaton Hydraulics). Note: After machining blank, part must be hardened per Eaton specification. Case Drain Port C 47,2 [1.6] Dia. D 2,5 [4.43] E 107,4 [4.] Full Form Dia. F 7,4 [.29]Min. Full Form Dia. G 6, [2.71] H 56,9 [2.24] Dia. J 1,29 [.720] K º Mating Coupling Blank Eaton Part No J C H K F D E G 25,9 [1.02] 24,1/21,1 [./.3] Case Flow Hole 7,6 [5.1] Square Face Seal or O-ring Seal 12,4 [.49] BEARINGLESS MOTOR DIMENSIONS Displacement X Y XX YY cm 3 /r [in 3 /r] mm [inch] mm [inch] mm [inch] mm [inch] 0 [ 6.7] 91,0 [3.5] 6, [5.7] 100,1 [3.94], [7.04] 1 [ 7.9],0 [3.74] 0, [5.94] 104,1 [4.10] 12,9 [7.20] 160 [ 9.9] 101,4 [4.00] 7,1 [6.19] 0,5 [4.] 19,2 [7.] 205 [12.5] 109,9 [4.33] 165,7 [6.52],9 [4.6] 197,6 [7.7] 2 [.0] 101,4 [4.00] 7,1 [6.19] 0,5 [4.] 19,2 [7.] 310 [19.0] 109,9 [4.33] 165,7 [6.52],9 [4.6] 197,6 [7.7] 3 [24.0],6 [4.75] 1,3 [6.94] 129,5 [5.10] 20,3 [.20] 4 [.0] 133,5 [5.26] 19,2 [7.] 2,5 [5.] 221,2 [.71] 625 [.0] 0,5 [5.93] 206,3 [.12] 9,5 [6.2],3 [9.] Fon: +49 (0) Fax: +49 (0)

11 Installation Information Bearingless 1 Internal spline in mating part to be as follows: Material to be ASTM A4, 620H. Carbonize to a hardness of HRc with case depth (to 50HRc) of 0,0-1,27 [ ] (dimensions apply after heat treat). 2 Mating part to have critical dimensions as shown. Oil holes must be provided and open for proper oil circulation. 3 Seal to be furnished with motor for proper oil circulation thru splines. 4 Some means of maintaining clearance between shaft and mounting flange must be provided. 5 Counterbore designed to adapt to a standard sleeve bearing 50,010-50,040 [ ] ID by 60,050-60,00 [ ] (Oilite bronze sleeve bearing). 6 Similar to SAE C Four Bolt Flange. 7 52, [2.0] dimension to be maintained when assembling shipping and installing unit to insure valve drive engagement with valve (this is required on displacement code number 24 only).,0/13,2 [.55/.52],9/,4 [./.33],6/52,6 [2./2.07] Coupling Depth 7 16 º º 1,5/0, [.06/.03] 5,1/4,6 [.20/.1] Dia. (2) Thru Oil Hole 2 31º 29º Case Flow 49,4/49,22 [1.9625/1.96] Dia. -D- 0,13 [.005] B 52,37 [2.062] R Dia. Min. 1,/1,2 [.07/.05] 5 Major 65,0/64,5 [2.56/2.54] Circular Tip R. Minor Finish Finish Fillet R. Pitch Form 5,6/5,1 [.22/.20],1/22,6 [.91/.9] Case Flow ( -B- ) Spline Pitch...10/20 Pressure Angle... Number of teeth Class of Fit... Ref. 5 Type of Fit... Side Pitch Diameter... Ref.,00 [ ] 0,20 [.00] D Base Diameter... Ref. 26,3965 [1.035] Major Diameter...33,43 [1.316] 33, [1.] Min. Min. Minor Diameter... 2,40-2,5 [ ] Form Diameter, Min....32,59 [1.23] Fillet Radius... 0,63-0, [ ] Tip Radius... 0,26-0,51 [ ] Finish...1,6 (63) Involute Profile Variation...+0,000-0,025 [ ] Total Index Variation...0,0 [.00] Lead Variation...0,013 [.0005] Circular Space Width: Maximum Actual...5,0 [.196] Minimum Effective...4,9 [.] Maximum Effective... Ref. 5,009 [.1972] Minimum Actual... Ref. 4,96 [.1963] Dimension Between Two Pins...Ref. 22,73-22,929 [ ] Pin Diameter...5,334 [.2100] Pins to Have 3,73 [.7] Wide Flat for Root Clearance Fon: +49 (0) Fax: +49 (0)

12 Dimensions Shafts 1 1/4 Inch Straight [600] Torque Nm [lb-in] 7,963/7,937 [.31/.3125] Square Key,9/6,6 [2.79/2.] End of Shaft to Mounting Surface (Std) 42,0/40,6 [1.65/1.60],33/,07 [1.391/1.1] 3/-16 UNC 1,7[.74] Deep 31,75/31,69 [1.250/1.24] Dia.,1 [2.09] Coupling 1 1/4 - Tooth Splined [600] Torque Nm [lb-in] 3/-16 UNC 1,7 [.74] Deep Spline to Fit ANSI B Flat Root Side Fit Tooth 12/24 Spline 40 mm Straight 972 [] Torque Nm [lb-in] 43,03/42,72 [1.694/1.62],000/7,0 [.39/.31] M12 x 1,75-6H 24,9 [.9] Deep,10 [1.500] Dia. 12,000/.7 [.4724/.4],1 [1.50] Min. Full Spline 31,7 [1.250] Dia. 40,02/39,99 [1.5/1.575] Dia. 1 1/2 Inch -Tooth Splined 972 [] Torque Nm [lb-in] Spline to Fit ANSI B Flat Root Side Fit Tooth 12/24 Spline 31,2 [1.] Min. Full Spline 3/-16 UNC 1,7 [.74] Deep,9/6,6 [2.79/2.] End of Shaft to Mounting Surface (Std),1 [2.09] Coupling 93,9/92,0 [3.696/3.622] End of Shaft to Mounting Surface (Std) 9,2/4,5 [.36/.1],7/69,3 [2.7/2.73] 1,3 [3.20] Coupling 66,/65,0 [2.63/2.56] End of Shaft to Mounting Surface (Std) 33,2/33,02 [1.310/1.0] Dia. 51, [2.04] Coupling 1 5/ Tapered 1-1/4-1 UNEF-2A 972 [] Torque Nm [lb-in] 41,326/41,275 [1.62/1.6250] Dia. Recommended Torque: (6 Nm [ lb-ft] Dry) (510 Nm [375 lb-ft] Lub) Plus Torque required to align the slotted nut with the Shaft Crosshole. 1-1/4-1 UNEF 4,1 [.16] Dia. Thru SAE J501 Standard Tapered Shaft 125,00 0, Taper per Meter [ Taper per Foot] Tapered Shaft Hub Data 59,1/56, [2.325/2.2] Slotted Hexagon Nut Hub 55,4 [2.1] 164,/162,1 [6.49/6.] End of Shaft to Mounting Surface (Whl),6 [3.00] 5,54/5,20 [.21/.205] 4,6 [.1] 31,7 [1.25],1/,2 [.45/.4375] Sq. Key,2 [.44],7 [.62] Fon: +49 (0) Fax: +49 (0)

13 Shaft Side Load Capacity These curves indicate the radial load capacity on the motor shaft(s) at various locations with an allowable external thrust load of 4 kg [1000 lb]. Note: Case pressure will increase the allowable Inward thrust load and decrease the allowable outward thrust load. Case pressure will push outward on the shaft at 94 kg/7 Bar [20 lb/100 PSI]. Thrust Load Standard Motor Straight and Splined Shafts [lb] [000] [00] [0] [5000] [0] [00] [2000] kg mm [inch] [-4] [-3] [-2] [-1] 0 [1] [2] [3] [4] [5] Axial Loads 4 kg [1000 lb] Each curve is based on B 10 bearing life (2000 hours of 12,000,000 shaft revolutions at 100 RPM) at rated output torque. To determine radial load at speeds other than 100 RPM, multiply the load values given on the bearing curve by the factors in the chart below. RPM Multiplication Factor For 3,000,000 shaft revolutions or 500 hours Increase these shaft loads 52%. Wheel Motor Tapered Shaft [lb] [00] [000] [00] [0] [5000] [0] [00] [2000] 0 kg mm Mounting Surface [inch] [-1] 0 [1] [2] [3] [4] [5] [6] [7] Mounting Surface Fon: +49 (0) Fax: +49 (0)

14 Case Pressure and Case Port Char-Lynn motors are durable and have long life as long as the recommended case pressure is not exceeded. Allowable case pressure is highest at low shaft speeds. Consequently, motor life will be shortened if case pressure exceeds these ratings (acceptability may vary with application). Determine if an external case drain is required from the case pressure seal limitation chart. Case Porting Advantage Contamination Control flushing the motor case. Cooler Motor exiting oil draws motor heat away. Extend Motor Seal Life maintain low case pressure with a preset restriction in the case drain line. 100 Case Pressure Bar 50 [PSI] 0 0 [2000] [00] [ 500] 0 Intermittent -- Case Drain Optional Case Pressure Seal Limitation Case Drain Required Continuous -- Case Drain Optional Speed RPM Fon: +49 (0) Fax: +49 (0)

15 Dimensions Ports 1-1/16-12 O-ring Ports (2) or G 3/4 (BSP) Ports (2) 4 Bolt 3/4 Inch Split Flange Ports to Fit SAE J51 c (2) Port B 7/16-20 UNF O-ring or G 1/4 (BSP) Case Drain Port 2,16/1,40 [.05/.055] Port B 7/16-20 UNF O-ring Case Drain Port 10,59/9,3 [.4/.7] 29,5/29,0 [1.16/1.] 13,2 [.52],7 [.62] º Port A 52,3/51, [2.06/2.04] Port A 47,63 [1.75],9 [.94] º 19,02/1,77 [.749/.739] º,2 [.44] 54,9 [2.16] 22, [.75] 52,3/51, [2.06/2.04] 69,6 [2.74] 5,9 [2.32] 5,9 [2.32],5 [3.01] 7/- O-ring Ports (2) or M22 x 1,5-6H Ports (2) Port B 29,5/29,0 [1.16/1.] 13,2 [.52] 69,6 [2.74] 5,9 [2.32] º 5,9 [2.32],7 [.62],5 [3.01] 42,7/,1 [1.6/1.50] 9/16-1 UNF O-ring or M12 x 1,5-6H O-ring Case Drain Port 6,73/5,99 [.265/.2] Port A 42,7/,1 [1.6/1.50] 6,9 [.27] Material Removed from this Housing for 7/- O-ring Ports and M22 x 1,5-6H Ports 73,4 [2.9] 5,7 [2.31] 5,7 [2.31],5 [3.01] 42,7/,1 [1.6/1.50] Fon: +49 (0) Fax: +49 (0)

16 Product Numbers Note: For Motors with a configuration Not Shown in the charts below: Use model code number system on the next page to specify product in detail. Use digit prefix 109-, 0-, or 1- plus four digit number from charts for complete product number Example 1-7. Orders will not be accepted without three digit prefix. MOUNTING SHAFT PORT SIZE DISPL. cm 3 / r [in 3 / r] / PRODUCT NUMBER 1 1/4 Inch Straight * [ 6.7] [ 7.9] [ 9.9] [12.5] [.0] [.1] [19.0] [24.0] [.0] [.0] 1 1/16 O-ring /4 inch Split Flange Standard SAE B-Mount 1 5/ Inch Tapered 1 1/4 Inch T Splined 1 1/16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange Standard SAE C-Mount 40 mm Straight G 3/4 (BSP) /4 Inch T Splined G 3/4 (BSP) /4 Inch Straight 1 1/16 O-ring /4 inch Split Flange Wheel Motor Bearingless * New Release 40 mm Straight G 3/4 (BSP) / Inch Tapered 1 1/4 Inch T Splined 1 1/16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange G 3/4 (BSP) Fon: +49 (0) Fax: +49 (0)

17 Model Code The following -digit coding system has been developed to identify all of the configuration options for the motor. Use this model code to specify a motor with the desired features. All digits of the code must be present when ordering. You may want to photocopy the matrix below to ensure that each number is entered in the correct box. M 0 4 * ** ** * * ** ** * ** * * ** ** ** ** ** * Product M - Motor 2, 3 Series 04 4, 5, 6 Displacement cm3/r [in3/r] cm 3 /r [6. in 3 /r] cm 3 /r [7. in 3 /r] cm 3 /r [9. in 3 /r] cm 3 /r [12.54 in 3 /r] cm 3 /r [.03 in 3 /r] cm 3 /r [.09 in 3 /r] 1-3. cm 3 /r [19.03 in 3 /r] cm 3 /r [22.52 in 3 /r] cm 3 /r [24.04 in 3 /r] cm 3 /r [.06 in 3 /r] cm 3 /r [34.1 in 3 /r] cm 3 /r [.07 in 3 /r] 7, Mounting Type AA Bearingless, 4 Bolt: [5.000] Pilot Dia..27 [.562] Dia. Holes on 1.92 [6.375] Dia. Bolt Circle AB Standard, 4 Bolt: [4.000] Pilot Dia..7 [.5] Slots on [5.000] Dia. Bolt Circle. (SAE B) AC Wheel, 4 Bolt: 139. [5.500] Pilot Dia..27 [.562] Dia. Holes on [6.500] Dia. Bolt Circle. AD Wheel, 4 Bolt: [5.000] Pilot Dia UNC-2B Threaded Holes on 7.62 [5.12] Dia. Bolt circle. AF Standard, 4 Bolt: [5.000] Pilot Dia..27 [.562] Dia. Holes on 1.92 [6.375] Dia. Bolt Circle. (SAE C) AH Standard: ISO Flange 125 B4hw (ISO 19/2) [4.920] Pilot Dia..27 [.562] Dia. Holes on [6.299] Dia. Bolt Circle AP Wheel, 4 Bolt: [6.] Pilot Dia. with 5. [.] Pilot Length and 1.00 [.9] Dia Holes on [7.74] Bolt Circle (ISO Compatible) 9, 10 Output Shaft 00 None (Bearingless) [1.250] Dia. Straight With UNC- 2B Thread,.1 [2.09] Max Coupling Length, 7.9 [.3125] Sq x [1.625] Straight Key [1.625] Dia. Tapered with.2 [.4375] Sq x [1.250] Straight Key, UNEF-2A Thread with Slotted Hex Nut [1.250] Dia. Flat Root Side Fit, Tooth, 12/24 DP Involute Spline,.1 [1.50] Minimum Full Spline Length with unc-2b Thread [1.500] Dia. Flat Root Side Fit, Tooth, 12/24 DP. Involute Spline, 31.2 [1.] Minimum Full Spline Length, with UNC-2B Thread in End [1.575] Dia. Straight with M12 x H Thread, 7.5 [.3132] x.979 [.4716] Wide X 69.9 [2.755] Straight Key [1.575] Dia. 10:1 Tapered Shaft per ISO R775 with UNF-2B Threaded in End, 12W x H L [.472W x.313h x 2.L] Key 22 None (Bearingless) European Spline [1.654] Dia. 10:1 Tapered Shaft per ISO R775 with UNF-2B Thread in End, 12W x H X 63L [.472W X.313H X 2.4L] Key, 12 Ports AA.75- UNF-2B SAE O-Ring Ports - Staggered Ports AB UN-2B SAE O-Ring Ports - Staggered Ports AC G 3/4 Ports - Staggered Ports AD [.750] 4 Bolt Split Flange Staggered Ports Standard Pressure Series (Code ) AE M22 X 1.5-6H O-Ring Port - Staggered Ports AG 12. [.500] Dia. Manifold Ports AJ Dash 12 Stc Type II+ (Snap to Connect) Ports - Staggered Ports 13, Case Flow Options 00 None UNF-2B SAE O-Ring Port with Shuttle UNF-2B SAE O-ring Port with Check Valve 03 G 1/4 BSP Straight Thread with Check Valve UNF-2B SAE O-ring Port with Reverse Flow Shuttle 10 Dash 6 Stc Type II + (Snap to Connect) Port Low Pressure Relief 0 None A Set at 4.5 Bar [65 lbf/in 2 ] B Set at.2 Bar [220 lbf/in 2 ] 16, Pressure/Flow Option 00 None 1 Geroler Option 0 Standard 19 Seal Option 0 Standard 1 Viton 4 Seal Guard 20, 21 Accessories 00 None AC M 12 Threaded Connector, Long Body Digital Speed and Direction Pickup (Two 36 Pulse Signals in Quadrature per Revolution Pin 1=Power Supply, Pin 2=Output Signal 1, Pin 3=Common, Pin 4=Output Signal 2) AD M 12 Threaded Connector, Digital Speed And Direction Pickup (One 72 Pulse per Rev Speed Signal and One Directional Signal (Pin 1=Power, Pin 2=Direction, Pin 2=Common, Pin 4=Speed) 22, Special Features (Hardware) 00 None Low Noise Valve Plate 24, 25 Special Features (Assembly) 00 None 26, 27 Paint/Packaging 00 No Paint, Individual Box AA Painted Low Gloss Black, Individual Box AB Epoxy Coated (Frost Gray), Individual Box 2, 29 Customer Identification 00 None Design Code F Sixth Feature in bold are preferred and allow for shorter lead time. Fon: +49 (0) Fax: +49 (0)

18 Order Numbers FT Article Number Eaton Code Type CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE (LOW LEAKAGE) CHAR-LYNN MOTOR SERIE VITON CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE K CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE 0 Fon: +49 (0) Fax: +49 (0)

19 Order Numbers FT Article Number Eaton Code Type CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE CHAR-LYNN MOTOR SERIE 0 Fon: +49 (0) Fax: +49 (0)