10,000 Series. Highlights C-6

Transcription

1 Highlights Features higher flows Benefits demanding mobile and industrial applications from Applications Description This is the biggest disc valve motor of our line with up to 45 GPM and 24,000 in-lb of torque in continuous mode, this motor is powerful and yet provides good efficiency. Specifications Geroler Element 4 Displacements ** Continuous (Cont.) Continuous rating, motor may be run continuously at these ratings. * Intermittent (Inter.) Intermittent operation, 10% of every minute. Boring Metal Forming Port Equipment -1

2 Specifications 10,000 SERIES MOTORS Displ. cm 3 /r [in 3 /r] 345 [21.0] 480 [29.3] 665 [40.6] 940 [57.4] Max. Speed Continuous Flow Intermittent Flow Continuous [45] [45] [45] [45] l/min [GPM] Intermittent 265 [] 265 [] 265 [] 265 [] Torque* Continuous 1040 [ 9220] 1475 [13050] 2085 [18450] 20 [23910] Nm [lb-in] Intermittent 1390 [12310] 1965 [17410] 20 [23080] 3440 [30460] Pressure Continuous 205 [3000] 205 [3000] 205 [3000] 190 [2750] bar Intermittent 275 [4000] 275 [4000] 260 [3750] [3500] [ PSI] Peak 275 [4000] 275 [4000] 275 [4000] 260 [3750] Weight Standard or 43,5 [96.0] 45,4 [100.0] 46,3 [100.0] 47,2 [104.0] kg [lb] Wheel Mount Bearingless 31,3 [69.0] 33,1 [73.0] 33,1 [73.0] 34,9 [77.0] *See shaft torque ratings for limitations.. Note: run motor for approximately pressure before application filled with fluid prior to any load applications. Maximum Inlet Pressure: Do not exceed pressure rating (see chart above). Maximum Return Pressure: drain line installed. Do not exceed pressure rating (see chart above). Maximum Case Pressure: bar [ PSI] : between inlet port and outlet port Continuous Rating: Motor may be run continuously at these ratings Intermittent Operation: 10% of every minute Peak Operation: 1% of every minute Recommended Fluids: type hydraulic oil with a viscosity of not less than SUS at operating temperature. Recommended System Operating Temp.: Recommended Filtration: -2

3 345 cm 3 /r [21.0 in 3 /r] Performance Data [250] [50 0 ] 35 [1000 ] [00] [2000] [2500] [3000] 205 [3500] [4000] 275 Motors run with high efficiency in all areas designated with a number best motor life select a and speed range shown in the light shaded area. at 120 SUS. Actual data may vary slightly from unit to unit in production. Flow LPM [GPM] [1] 3,8 [2] 7,5 [4] [8] 30 [12] 45 [16] [20] 76 [24] 91 [28] 106 [32] 121 [36] 136 [40] 1 [45] [60] 227 [] 265 Continuous [250] [760] 85 6 [1040] 120 [1040] [1020] 1 62 [990] 94 [960] 125 [930] 7 [890] [850] [810] [760] [710] [647] [430] [500 ] 35 [40] [2] 13 [2130] 29 [2] [2080] 93 [2060] 124 [2020] [1980] [1940] [1900] [1850] [1800] [1740] [20] 473 [1360] [1000 ] [3120] [4320] [4310] [4290] [42] [4] [4200] [4] [4130] [4080] [4040] [3990] [3920] [3710] [3540] cm 3 /r [29.3 in 3 /r] [00] [4640] [6500] [6490] [6480] [6450] [6420] [6390] [6350] [6310] [62] [6220] [6] [6] [5890] [5730] [2000] [8690] [8680] [8660] [8630] [8600] [85] [8530] [8490] [8450] [8400] [8350] [8290] [80] [7910] [2500] [108] [10860] [10840] [10820] [10790] [10750] [10720] [10680] [10630] [90] [40] [104] [10260] [10100] [3000] 205 [13050] [13030] [13000] [129] 1465 [12940] [12900] [12860] [12820] 1450 [127] [12720] [12660] [12440] [12280] [3500] [230] [210] [180] [0] [120] [080] [040] [ 000] [4000] 275 [17410] [17390] [173] [17] [17300] Flow LPM [GPM] [1] 3,8 [2] 7,5 [4] [8] 30 [12] 45 [16] [20] 76 [24] 91 [28] 106 [32] 121 [36] 136 [40] 1 [45] [60] 227 [] 265 [600] 3 [ 740] [730] [720] [0] [680] [660] [630] 266 [6 0 0 ] 310 [5] [540] [500] [460] [1310 ] 0 1 [10] 19 [00] 41 [1490] 86 [14] [1450] [1430] [0] [13] [1] [1310] [12] [1220] 500 [1080] [960] 784 [3050] 345 [3040] [3030] 82 [3020] 127 [3000] 172 [29] [2950] [2920] [2890] [2850] [2820] [2760] [2620] [2510] [2510] Torque [lb-in] 285 } Nm 777 Speed RPM [4600] [4590] [4580] 5 78 [4560] [4540] [4520] [4490] [4460] [4430] [4400] [4360] [4300] [4160] [4050] [6] [6] [20] [0 0] [6080] [6060] [6030] [6000] [59] 675 [5940] [5910] [5840] [5710] [5590] [7680] [7680] 8 26 [76] 865 [7650] [7630] [7600] [7580] [7550] [7520] [7480] [7450] [7380] [7250] [7] [9220] [9210] [9190] 1040 [9] [90] [9120] [9090] [9060] [9030] [8990] [8910] [8800] [8680] [107] [10750] [10740] [10720] [10690] [10660] [10640] [100] [] [40] [10450] [12310 ] [12300] [12280] [12260] [12230] [12210] [12180] [120] [12120]

4 Performance Data Motors run with high efficiency in all areas designated with a number best motor life select a and speed range shown in the light shaded area. at 120 SUS. Actual data may vary slightly from unit to unit in production. Continuous Flow LPM [GPM] [1] 3,8 [2] 7,5 [4] [8] 30 [12] 45 [16] [20] 76 [24] 91 [28] 106 [32] 12 1 [36] 136 [40] 1 [45] [60] 227 [] 265 [250] [1440] [0] [1360] 5 89 [500] 35 [14] [3010] 3 [4550] 5 3 [2980] [4530] [60] [2950] [4490] [6040] [2910] [4450] [70] [5990] [2860] [4400] [5940] cm 3 /r [40.6 in 3 /r] Pressure Bar [PSI] [750] 50 [1000] [1250] 85 [00] [1480] [3020] [4560] [6] [7650] [9200] [14 ] [1310] [1260] 135 [1200] [1] [1080] [1010] [920] 254 [0] 338 [380] [3010] [4550] [00] [7640] [9190] [2800] [2750] [2690] [2620] [2550] [2460] [20] [1930] [4350] [4290] [5890] [5840] [4230] [57] [4160] [4100] [4000] [30] [34] [00] [7630] [5710] [5640] [5550] [5] [5010] [7580] [7540] [9160] [9120] [9080] [7490] [9030] [7440] [7380] [7320] [7250] [7180] [90] [6780] [6560] [8980] [8920] [8860] [8800] [8730 ] [8630] [8330] [8100] [1750] 120 [10730] [100] [106] 1205 [10620] [80] [2000] [10740] 12 5 [12280] [20] [104] [10400] [10] [102] [10180] [98] [9640] [122] 1385 [12250] [12210] [12] [12120] [120] [12010] [11950] [11880] [11810] [11720] [11420] [11190] [2250] 5 [13790] [13750] [13710] [13660] [2500] [330] [16880] [300] [2750] 190 [13830] [3] [16910] [13820] [360] [16900] [130] [13550] [13490] 25 [13430] 193 [13360] 10 2 [13260] [12960] [260] [210] [0] [100] [040] [149] [14900] [14810] [16840] [16800] [16750] [160] [16640] [16580] [16510] [16440] [3000] 205 [18450] [18420] [18380] [18] [18300] [18] [3250] 225 [3500] [19990] [] [19960] [210] [19930] [214] [19890] [19840] 2 99 [20] [3750] 260 [23080] 20 8 [23050] [23020] cm 3 /r [57.4 in 3 /r] Pressure Bar [PSI] [34] Torque [lb-in] 390 } Nm 391 Speed RPM 390 } Nm 391 Speed RPM Flow LPM [GPM] [1] 3, 8 [2 ] 7,5 [4] [8 ] 30 [12 ] 45 [16] [20] 76 [24] 91 [28] 10 6 [32] 121 [36] 136 [40] 1 [45] [60] 227 [] 265 [250] [2040] [1990] [1930] [500] 35 [2080] 3 [4260] [6440] [4220] [6400] [4] [6350] [4] [4040] [750] 50 [1000] [8590] 9 28 [8540] [6290] 710 [6220] 5 77 [8480] [8410] [1250] 85 [107] [10720] [10660] [90] [00] [2090] 7 [42] [6450] [8640] [10820] [13000] 14 3 [2080] [1860] [1780] [0] [1620] [20] 143 [1420] [1290] [860] [540] [4260] [39] [3890] 440 [6440] [60] [60] [8620] [8330] [8250] [10810] [20] [10440] [12990] [12950] [12900] [12840] [1277 0] [120] [12620] [3800] [5980] [8160] [10350] [12530] [3710] [5890] [30] [5790] [3480] [3040] [2720] [5660] [5230] [4910] [80] 910 [79] [7840] [7410] 835 [90] [10260] [10160] 10 5 [10020] [9600] [92] [12440] [12] [12210] [11780] [11460] [1750] 120 [] [090] 5 42 [030] 0 58 [14960] [2000] [190] [173] [] [17360] [17320] [172] [17210] [17] [14880] [14800] 1675 [14720] [14620] [14520] [14400] [] [16990] [2250] 5 [19540] [19500] [19450] [19390] [19320] [2500] [21720] [23910] 20 7 [260 90] [282] [30460] [21690] [21640] [2750] 190 [238] [3000] 205 [3250] 225 [3500] -4

5 Dimensions Ports Standard Rotation Viewed from Shaft End Standard Mount Port B Y Max. X 9/16-18 UNF O-ring Case Drain Port 7/8-14 UNF O-ring Port- Alternative Case Drain (2) 22,4/20,8 [.88/.82] 14,5/13,2 [.57/.52] 17,02/16,51 [.6/.650] Dia. (4) 0,1 [5.91] Max 127,00/126,87 [5.000/4.995] Dia. 147,1 [5.79] Max. 7/8-14 UNF O-ring Case Drain Port (2) STANDARD MOUNT MOTOR DIMENSIONS Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 345 [21.0] 282,4 [11.12] 380,7 [14.99] 480 [29.2] 295,1 [11.62] 393,4 [.49] 665 [40.6] 295,1 [11.62] 393,4 [.49] 940 [57.4] 313,4 [12.34] 411,7 [16.21] 67,4/66,2 [2.65/2.] 114,3 [4.50] Square 1,92 [6.375] Dia. Bolt Circle -5

6 Dimensions Ports Standard Rotation Viewed from Shaft End Wheel Mount Port B Y Max. X 9/16-18 UNC O-ring Case Drain Port 131,1/127,8 [5.16/5.03] 21,1/20,0 [.83/.79] 184,9 [7.28] Square Max. 127,0 [5.00] Dia. 139,7 [5.50] Dia. 177,80/177,67 [7.000/6.995] Dia. (2) 5,9/4,8 [.23/.19] 209,55 [8.250] Dia. Bolt Circle 17,02/16,51 [.6/.650] Dia. (4) WHEEL MOUNT MOTOR DIMENSIONS Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 345 [21.0] 166,9 [6.57] 265,9 [10.47] 480 [29.2] 179,6 [7.07] 278,6 [10.97] 665 [40.6] 179,6 [7.07] 278,6 [10.97] 940 [57.4] 197,8 [7.79] 297,2 [11.] -6

7 Dimensions Ports Standard Rotation Viewed from Shaft End Bearingless Port B Y Max. X 20,88/20,52 [.822/.808] Dia. Thru (4) 1,64 [6.364] Square 200,5 [7.89] Square Max. 9/16-18 UNF O-ring Case Drain Port 19,1/16,5 [.75/.65] 228,60 [9.000] Dia. Bolt Circle 2,40/2,27 [6.000/5.995] Dia. 12,7/12,4 [.50/.49] Mating Coupling Blank BEARINGLESS MOTOR DIMENSIONS Displacement X Y cm 3 /r [in 3 /r] mm [inch] mm [inch] 345 [21.0] 8,0 [6.22] [10.09] 480 [29.2],7 [6.72] 269,0 [10.59] 665 [40.6],7 [6.72] 269,0 [10.59] 940 [57.4] 189,0 [7.44] 287,5 [11.32] Dimension D mm [inch] Eaton Part No ,6/128,5 [5.26/5.06] ,0/0,9 [6.14/5.94] application information, contact your Eaton representative (mating coupling Hydraulics). D Note: part must be hardened per Eaton specification. -7

8 Installation Information 51,1 1,8 [ ] -B- Coupling Depth 89,2 0.8 [ ] 1 Internal spline in mating part to be as follows: Material to be ASTM A304, 8620H. Carbonize to a hardness of HRc with case depth (to 50HRc) of 0,076-1,02 [ ] (dimensions apply after heat treat). Case Flow -A- 43,56 [1.7] Min. Case Flow Major Circular Tip R. Minor Finish Finish Fillet R. Pitch Form Spline Pitch...10/20 Pressure Angle...30 Number of teeth Class of Fit... Ref. 5 Type of Fit... Side Pitch Diameter...Ref. 40, [ ] 0,25 [.010] D Base Diameter... Ref. 35, [ ] Major Diameter...43,56 [1.7] Max. 43,18 [1.0] Min. Min. Minor Diameter... 36,83-37,08 [ ] Form Diameter, Min....42,47 [1.672] Fillet Radius... 0,64-0,76 [ ] Tip Radius... 0,25-0,51 [ ] Finish...1,6 (63) Involute Profile Variation...+0,000-0,028 [ ] Total Index Variation...0,041 [.0016] Lead Variation...0,013 [.0005] Circular Space Width: Maximum Actual...4, [.16] Minimum Effective...3,995 [.73] Maximum Effective...Ref. 4,056 [.97] Minimum Actual...Ref. 4,018 [.82] Dimension Between Two Pins... Ref. 26,929-27,084 [ ] Pin Diameter...Ref. 34,272-34,450 [ ] Wide Flat for Root Clearance -8

9 Dimensions Shafts 2 1/4 Inch Straight 2712 [00] Max. Torque Nm [lb-in] 2,73/12, 501/.500] q. Key 1/2-20 UNF x 23,8 [.94] Deep 57.0/57,137 [2.2500/2.2495] Dia. 63,5 [2.50] 62,92/62,66 [2.477/2.467] 97,5 [3.84] Max. Coupling 2 1/4 Inch Tapered 114,0/112,3 [4.49/4.42] End of Shaft to Mounting Surface (Std) 2712 [00] 222,5/219,7 [8.76/8.65] Max. Torque End of Shaft to Mounting Surface (Whl) Nm [lb-in] 57, [2.250] Dia. 4,32/3,81 [./.0] Dia. Thru 1-1/2-18 UNEF 94,7 [3.73] SAE J501 Standard Tapered Shaft 125,00 0,17 Taper per Meter [1.500±.002 Taper per Foot] 50,8 [2.00] 14,313/14,287 [.5635/.5625] Sq. Key 7,14/6,80 [.281/.268] 2 1/8 Inch 16 Tooth Splined Tapered Shaft Hub Data 2712 [00] Max. Torque Nm [lb-in] Involute Spline Flat Root Major Dia. Fit 8/16 Pitch 16 Toot h per ANSI B92.1, ,7/89,9 [3./3.54] End of Shaft to Mounting Surface (Std) 75,0 [2.95] Max. Coupling 52,1 [2.05] Min. Full Spline Recommended Torque: (10 Nm [850 lb-ft] Dry) ( 880 Nm [650 lb-ft] Lub) Plus Torque required to align the slotted nut with the Shaft Crosshole. Hub 76,2 [3.00] 1/2-20 UNF x 23,8 [.94] Deep 53,972 [2.1249] Major Dia. 57, [2.250] Dia. Slotted Hexagon Nut 1-1/2-18 UNEF 1,52 [.06] x 45 Chamfer 60,0 [2.37] 10,9 [.43] 4,1 [.16] 30 30,7 [.62] -9

10 Side Shaft Load Capacity radial load capacity on the motor shaft at various locations with an external allowable thrust load is Note: Case pressure will increase the allowable inward thrust load and decrease the allowable outward thrust load. Case pressure will push outward on the shaft Each curve is based on Thrust Load Max. Axial Loads 908 kg [2000 lb] B 10 bearing life (2000 hours of 12,000,000 shaft revolutions at 100 RPM) at rated output torque. multiply the load values given on the bearing curve by the factors in the chart below. RPM Multiplication Factor kg kg [lb] [10000] [ 9000] [ 8000] [ 00] [ 6000] [ 5000] [ 4000] [ 3000] mm [-5] [-4] [-3] [-2] [-1] 0 [1] [2] [3] [4] [5] [inch] Mounting Surface [lb] [10000] [ 9000] [ 8000] [ 00] [ 6000] [ 5000] [ 4000] [ 3000] mm [-1] 0 [1] [2] [3] [4] [5] [6] [7] [8] [9] [inch] Mounting Surface - these shaft loads 52%. -10

11 Dimensions 1 1/4 Inch Split Flange Ports (2) Port B,10 [.594] (2) 30,20 [1.188] (2) 7/16-14 UNC x 29,2 [1.] Deep (8) Port A 29,40 [1.6] 9/16-18 UNF O-ring Case Drain Port 29,5/27,4 [1.16/1.08] 58, [2.312] 75,5/ [2.97/2.95] 30,8/29,2 [1.21/1.] 102,2/101,0 [4.02/3.98] 182,9 [7.20] Max. 1 5/16-12 O-ring Ports (2) Port B 9/16-18 UNF O-ring Case Drain Port Port A 29,5/27,4 [1.16/1.08] 76,2/74,1 [3.00/2.92] 45 30,8/29,2 [1.21/1.] 106,2 [4.18] 184,7 [7.27] End View Common Dimensions 4,0 [6.06] Max. 74,0/72,1 [2.91/2.84] 9/16-18 UNF O-ring Case Drain Port 16,8/,7 [.66/.62] -11

12 Product Numbers Note: with a configuration Not Shown in the chart below: Use model code number system on the next page to specify product in detail. digit number from charts for Example Orders will not be accepted without three digit prefix. MOUNTING SHAFT PORT SIZE DISPL. cm 3 / r [in 3 / r] / PRODUCT NUMBER 345 [21.0] 480 [29.3] 665 [40.6] 940 [57.4] 2 1/4 Inch Straight 1 5/16 O-ring /4 inch Split Flange Standard SAE C-Mount Wheel Motor Bearingless 2 1/8 Inch 16 T Splined 2 1/4 Inch Tapered 2 1/4 Inch Straight 2 1/8 Inch 16 T Splined 2 1/4 Inch Tapered 1 5/16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange /16 O-ring /4 inch Split Flange

13 Model Code identify all of the configuration options for the 10,000 Series motor. Use this model code to specify a motor with the to ensure that each number is entered in the correct box. M 1 0 * * * * * * * * * * * * 0 0 * * * * 0 0 * * * * 0 0 * Product M Motor 2, 3 Series 10 10,000 Series 4, 5, 6 Displacement cm3/r [in3/r] [20.98] [29.26] [40.60] [57.41] 7, 8 Mounting Description AA Standard, 4 Bolt: 127,0 [5.00] Pilot Dia. 16,76 [.660] Dia. Holes on 1,92 [6.375] Dia. Bolt Circle AB Wheel, 4 Bolt: 16,76 [.660] Dia. Holes on 209,55 [8.250] Dia. Bolt Circle 9, 10 Output Shaft Description , [2.250] Dia. Straight with UNF-2B Thread in End, 12.7 [.50] Square x 63,5 [2.50] Straight End 02 57, [2.250] Dia..125:1 Tapered Shaft Per SAE J512 with UNEF-2A Threaded Shaft End and Slotted Hex Nut, 14,288 [.5625] Square x 50,8 [2.00] Straight Key 03 53,98 [2.125] Dia. Flat Root, Major Dia. Fit, 16 Tooth, 8/16 DP, 30 Degree Involute Spline with UNF-20 Thread in End. 52,07 [2.050] Minimum Full Spline Length 11, 12 Ports AA UN O-Ring Staggered Ports AB 31,75 [1.250] Dia. 4 Bolt Split Flange Staggered Ports with UNC-2B Tapped Mounting Holes 13, 14 Case Flow Options UNF-2B Case Drain SAE O-Ring Port Low Pressure Relief 0 None 16, 17 Pressure/Flow Option 00 None 18 Geroler Option 0 Standard 19 Seal Option 0 Standard 4 Seal Guard 20, 21 Accessories 00 None 22, 23 Special Features (Hardware) 00 None 24, 25 Special Features (Assembly) 00 None AA Reverse Rotation 26, 27 Paint / Packaging 00 None AA 28, 29 Customer Identification 00 None 30 Design Code C Third (Standard and Wheel Mounts) D Fourth (Bearingless Mount) Feature in bold are preferred and allow for shorter lead time. -13