C9: BMM, BMP, BMR, BMH, BMJ Series & Valves CONTENT. Usage Guide 2. BMM Series Hydraulic Motors 3. BMP Series Hydraulic Motors 11

Transcription

1 C9: BMM, BMP, BMR, BMH, BMJ Series & Valves CONTENT Usage Guide 2 BMM Series Hydraulic Motors 3 BMP Series Hydraulic Motors 11 BMR Series Hydraulic Motors 24 BMH Series Hydraulic Motors 35 BMJ Series Hydraulic Motors 43 Valves for Hydraulic Motors 46 The manufacturer reserves the right to change the technical specifications without notice 1

2 USAGE GUIDE For optimal working, we recommend the following: 1. Oil Temperature Normal: 0 c 0 c Maximum: 90 0 c (maximum one hour) 2. Filtering & Oil Cleanliness System Filtration: µm nominal. A magnet should be installed in the filter or at the bottom of the tank to prevent ingress into the system. 3. Viscosity Based on external ambient temperature and type of application. Recommended Oil Viscosity is 32 74mm 2 /s. 4. The motors can be operated in Parallel or Series. When the pressure of the case exce eds Bar, it is recommended to install an external drain line to the tank. 5. Various output shaft and flange options are available. 5.1 Various Manifold Mount Valving available. 6. The optimal operation condition should be at the 1/3 2/3 of the rated operation. 7. In order to obtain a longer life, operating motor should operate for first hour under % of rated pressure. Motor must be filled with oil prior to being put under load. SPECIFICATION DATA OF HYDRAULIC MOTOR Distribution Type Axial Distribution Model Displacement (cm 3 /rev.) Operating Pressure (Bar) Speed Range (rpm) Output Power (kw) BMP BMR BMH BMM BMJ

3 BMM SERIES HYDRAULIC MOTOR BMM Series compact design providing high torque capacity from a small package giving a high power to weight ratio. Characteristic Features: Advanced manufacturing design of the Gerotor gear set, which provide hydraulic circuits, high efficiency and long life High pressure shaft seals sllow for use in both Parallel & Series circuits Advanced design giving both high power and low weight Main Specifications Type BMM Geometric Displacement (cm 3 /rev.) Speed (rpm) Rated Torque (Nm) Rated Peak Output (kw) Rated Pressure Drop (Bar) Rated Peak Flow (L/min) Rated Weight (kg) Type BMM 8- (Bar) Inlet Pressure Rated Speed and Rated Torque: Output value of speed and torque under rated flow and rated pressure Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute 3

4 PERFORMANCE DATA BMM8 [8.2cm 3 /rev.] BMM12.5 [12.9cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) Flow (L/min) Flow (L/min) BMM [19.9cm 3 /rev.] BMM32 [31.6cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) Flow (L/min) Flow (L/min) Cont 4

5 PERFORMANCE DATA BMM [39.8cm 3 /rev.] BMM [.3cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) Flow (L/min) Flow (L/min) Cont Torque (Nm) 37 Speed (rpm) 7 5

6 BMM END PORT DIMENSIONS & MOUNTING DATA M, U F MODEL L L1 L L1 BMM BMM Mounting M, U F BMM Code 1E (Depth) 1U (Depth) 1E (Depth) 1U (Depth) BMM C M6 () ¼-28UNF-2B () BMM D G3/8 (12) 9/16-18UNF (12) G3/8 (12) 9/16-18UNF (12) BMM T G1/8 (8) 3/8-24UNF (8) G1/8 (8) 3/8-24UNF (8) 6

7 BMM SIDE PORT DIMENSIONS & MOUNTING DATA M, U F MODEL L L1 L L1 BMM BMM Mounting M, U F BMM Code E (Depth) U (Depth) E (Depth) U (Depth) BMM C M6 () ¼-28UNF-2B () BMM D G3/8 (12) 9/16-18UNF (12) G3/8 (12) 9/16-18UNF (12) BMM T G1/8 (8) 3/8-24UNF (8) G1/8 (8) 3/8-24UNF (8) 7

8 SHAFT EXTENSIONS FOR BMM MOTORS 8

9 BMM SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE In applications without drain line, output shaft seal exceeds a bit of the pressure in the return line. When applications use the drain line, the pressure of output shaft seal equals the pressure in drain line. Bar DIRECTION OF SHAFT ROTATION STATUS OF THE SHAFT S RADIAL FORCE Fr = 61.5+L N Fr = Radial Force (N) L = Distance (mm) N = Speed (rpm) Rhomb-Flange L = 15mm Square-Flange L = mm 9

10 BMM SERIES HYDRAULIC MOTOR ORDER INFORMATION Code Displacement Code Output Flange Code Shaft Code Port M U F 3-M6 Circle-Flange, Pilot 31.5x5 3-1/4-28UNF Circle Flange, Pilot 31.5x5 2-9 Rhomb-Flange, Pilot 63x2 A B C Shaft 16, Parallel Key 5x5x16 Shaft 15.8, Parallel Key 4.8x4.8x /8 Shaft 16.5, Involute B17x14, DIN5482 E U 1E 1U G 3/8, G 1/8 9/16-18UNF, 3/8-24UNF Rear Port G 3/8, G 1/8 Rear Port 9/16-18UNF, 3/8-24UNF

11 BMP SERIES HYDRAULIC MOTOR BMP series motors are medium speed, high torque motors designed on an internal gear design consisting of a rotor and stator. These motors are suitable for long operating periods at moderate pressures. Characteristic Features: Advanced manufacturing design for the Gerotor gear set, which provide high starting torque, high efficiency and long life Motors have high pressure shaft seals which can be used in Parallel or Series Smooth running over the entire speed range Main Specifications Technical data for BMP with 25 and 1 in and 1 in splined and tapered shaft TYPE BMP, BMPH & BMPW Geometric Displacement (cm 3 /rev.) Speed (rpm) Torque (Nm) Peak Output (kw) Pressure Drop (Bar) Peak Flow (L/min) 55 Weight (kg) Technical data for BMP with 31. and 32 shaft TYPE BMP, BMPH & BMPW Geometric Displacement (cm 3 /rev.) Speed (rpm) Torque (Nm) Peak Output (kw) Pressure Drop (Bar) Peak Flow (L/min) 55 Weight (kg) Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute 11

12 PERFORMANCE DATA BMP36 [36cm 3 /rev.] BMP [51.7cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/Min) Max Max Flow (L/Min) Max Max BMP80 [77.7cm 3 /rev.] BMP0 [96.2cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/Min) Max Max Flow (L/Min) Max Max BMP125 [1.2cm 3 /rev.] BMP1 [157.2cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/Min) Max Max Flow (L/Min) Max Max Torque (Nm) 124 Speed (rpm)

13 PERFORMANCE DATA BMP0 [194.5cm 3 /rev.] BMP2 [2.3cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/Min) Max Max Flow (L/Min) Max Max BMP315 [314.5cm 3 /rev.] BMP0 [389.5cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/Min) Max Max Flow (L/Min) Max Max BMP0 [486.5cm 3 /rev.] Pressure (Bar) Torque (Nm) 234 Speed (rpm) 185 Flow (L/Min) Max Max Torque (Nm) 312 Speed (rpm)

14 BMP DIMENSIONS AND MOUNTING DATA 14

15 BMPH DIMENSIONS AND MOUNTING DATA 15

16 BMP SHAFT EXTENSIONS DIMENSIONS DATA 16

17 BMP SHAFT EXTENSIONS DIMENSIONS DATA Motor Mounting Surface 17

18 BMPH SHAFT EXTENSIONS DIMENSIONS DATA Motor Mounting Surface 18

19 BMPH SHAFT EXTENSIONS DIMENSIONS DATA Motor Mounting Surface 19

20 BMPW DIMENSIONS & MOUNTING DATA

21 BMPW ORDER INFORMATION Code Disp Flange Output Shaft Main Port & Drain Port Rotation Direction Paint Special Function BMPW Omit Wheel-Flange Pilot 80x7.5 A C E T Shaft 25k6, Parallel Key 8x7x32 Shaft 25.4, Parallel Key 6.35x6.35x31. Shaft 25.4, Splined Key SAE 6B Cone Shaft 28.56, Parallel Key B5x5x14 G S M G1/2, G1/4 7/8-14 Oring, 7/16-UNF M22x1.5, M14x1.5 Omit R Standard Opposite 00 Omit B S No Paint Blue Black Silver Grey Omit N O Standard High radial force No case drain 21

22 BMP, BMPH, BMPW SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE Bar In applications without drain line, the shaft seal pressure is equal to the pressure in the return line. When applications use the drain line, the pressure behind the output shaft seal equals the pressure in drain line. DIRECTION OF SHAFT ROTATION When facing shaft end of motor, shaft to rotate: Clockwise when Port A is pressurised Counter-clockwise Port B is pressurised STATUS OF THE SHAFT S RADIAL FORCE 22

23 ORDER INFORMATION Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 A Shaft 25, Parallel Key 8x7x32 D G1/2 Manifold Mount 4xM8, G1/4 B Shaft 32, Parallel Key x8x45 80 C Shaft 25.4, Parallel Key 6.35x6.35x31. M M22x1.5 Manifold Mount 4xM8, 0 E Shaft 25, Splined Tooth SEA 6B M14x1.5 Omit Standard Rhomb-Flange, Pilot 82.5x8 125 R 00 No Paint N Large Radial Force Short shaft 25.4, Parallel Key 6.35x6.35x Rhomb-Flange, Pilot 82.5x8 S 7/8-14 O-Ring Manifold 4x5/16- Omit Standard Omit Blue AX Large Axial Force BMP 1 F H4 Shaft 31., Splined Tooth 14-DP12/24 4-3/8-16 Square-Flange, Pilot 44.4x2.8 18UNC, 7/16-UNF R Opposite B Black O No Case Drain 0 H5 FD 4-M Square-Flange, Pilot 44.4x2.8 Long Shaft 31., Splined Tooth 14-DP12/24 S Silver Grey F Free Running 2 G Shaft 31., Parallel Key 7.96x7.96x31. P 1/2-14 NPFT Manifold 4x5/16- LS Low Speed 315 T Cone Shaft 28.56, Parallel Key B5x5x14 18UNC, 7/16-UNF 0 T3 Cone Shaft 31., Parallel Key 7.96x7.96x R PT(Rc)1/2 Manifold 4xM8,PT(Rc)1/ Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 K Shaft 25.4, Woodruff Key 25.4x6.35 S Shaft 25.4, Splined Tooth SEA 6B G 80 A Shaft 25, Parallel Key 8x7x32 S P T BMPH R Omit Standard B4 R Opposite 0 R Shaft 25.4, Parallel Key 6.35x6.35x H Rhomb-Flange, Pilot 82.5x2.8 H Shaft 25.4, Pin Hold.3 H Rhomb-Flange, Pilot 82.5x2.8 1 H1 Shaft 25.4, Pin Hole 8 H4 4-3/8-16 Square-Flange, Pilot 44.4x2.8 0 H5 D Shaft 22.22, Parallel Key 6.35x6.35x M Square-Flange, Pilot 44.4x2.8 2 I Shaft 22.22, Splined Tooth 13-DP16/ T2 Cone Shaft 25.4, Woodruff Key 25.4x P Shaft 25, Parallel Key 8x7x28 0 J Shaft 25, Parallel Key 7x7x32 B5 G1/2 G1/4 7/8-14 O-Ring 7/16-UNF (G1/4) 1/2-14 NPTF, 7/16-UNF (G1/4) 3/4-16 O-Ring, 7/16-UNF PT(Rc)1/2 PT(Rc)1/4 O-Ring Manifold 4x5/16-18UNC, 7/16-UNF(G1/4) O-Ring Manifold 4xM8 7/16- UNF(G1/4) 00 Omit B S No Paint Blue Black Silver Grey Omit N AX O F LS Standard Large Radial Force Large Axial Force No Case Drain Free Running Low Speed 23

24 BMR SERIES HYDRAULIC MOTOR BMR Series motors are medium speed high torque motors designed on an internal gear design consisting of a rotor and stator. These motors are suitable for long operating periods at moderate pressures. Characteristic Features: Advanced manufacturing design for the Geroler gear set, which provide high starting torque, high efficiency and long life Motors have high pressure shaft seals which can be used in Parallel or Series Smooth running over the entire speed range Main Specifications Type BMR & BMRS Geometric Displacement (cm 3 /rev.) Speed (rpm) Torque (Nm) Rated Output (kw) Rated Pressure Drop (Bar) Rated Flow (L/min) Weight (kg) Rated Speed & Rated Torque: Output value of speed and torque under rated flow and rated pressure Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute 24

25 PERFORMANCE DATA BMR [51.3cm 3 /rev.] BMR80 [80.6cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/min) Flow (L/min) BMR0 [0.8cm 3 /rev.] BMR125 [124.9cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/min) Flow (L/min) Cont Torque (Nm) 167 Speed (rpm)

26 PERFORMANCE BMR1 [157.2cm 3 /rev.] BMR0 [199.2cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/min) Flow (L/min) BMR2 [252cm 3 /rev.] BMR315 [314.5cm 3 /rev.] Pressure (Bar) Pressure (Bar) Flow (L/min) Flow (L/min) Cont Torque (Nm) 5 Speed (rpm)

27 PERFORMANCE BMR3 [370cm 3 /rev.] Pressure (Bar) Flow (L/min) Cont Torque (Nm) 2 Speed (rpm)

28 BMR DIMENSIONS AND MOUNTING DATA 28

29 BMRS DIMENSIONS AND MOUNTING DATA 29

30 BMR SHAFT EXTENSIONS DIMENSIONS DATA

31 BMRS SHAFT EXTENSIONS DIMENSIONS DATA 31

32 BMRS SHAFT EXTENSIONS DIMENSIONS DATA 32

33 BMR, BMRS SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE Bar In applications without drain line, the shaft seal pressure is equal to the pressure in the return line. When applications use the drain line, the pressure behind the output shaft seal equals the pressure in drain line. DIRECTION OF SHAFT ROTATION When facing shaft end of motor, shaft to rotate: Clockwise when Port A is pressurised Counter-clockwise Port B is pressurised STATUS OF THE SHAFT S RADIAL FORCE 33

34 ORDER INFORMATION Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 A Shaft 25, Parallel Key 8x7x32 D G1/2 Manifold Mount 4xM8, G1/4 B Shaft 32, Parallel Key x8x45 80 C Shaft 25.4, Parallel Key 6.35x6.35x31. M M22x1.5 Manifold Mount 0 E Shaft 25, Splined Tooth SEA 6B 4xM8, M14x1.5 Omit Standard Rhomb-Flange, Pilot 82.5x8 00 No Paint N Large Radial Force 125 R Short shaft 25.4, Parallel Key 6.35x6.35x Rhomb-Flange, Pilot 82.5x8 S 7/8-14 O-Ring Manifold Omit Standard Omit Blue AX Large Axial Force BMR 1 H4 F 4-3/8-16 Square-Flange, Pilot 44.4x2.8 Shaft 31., Splined Tooth 14-DP12/24 4-5/16-18UNC, 7/16-UNF R Opposite B Black O No Case Drain 0 H5 4-M Square-Flange, Pilot 44.4x2.8 FD Long Shaft 31., Splined Tooth 14-DP12/24 S Silver Grey F Free Running 2 G Shaft 31., Parallel Key 7.96x7.96x31. P 1/2-14 NPFT Manifold LS Low Speed 315 T Cone Shaft 28.56, Parallel Key B5x5x14 4-5/16-18UNC, 7/16-UNF 0 T3 Cone Shaft 31., Parallel Key 7.96x7.96x25.4 R PT(Rc)1/2 Manifold 4-M8,PT(Rc)1/ Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 36 K Shaft 25.4, Woodruff Key 25.4x6.35 D G1/2 Manifold Mount 4-M8, G1/4 S Sub-Shaft 25.4, Splined Tooth SAE 6B 80 A Shaft 25, Parallel Key 6.35x6.35x31. M M22x1.5 Manifold Mount 4-0 R Shaft 25.4, Splined Tooth SAE 6B M8,M14x1.5 Omit Standard 125 H Rhomb-Flange, Pilot 82.5x2.8 H Short Shaft 25.4, Parallel Key 00 No Paint N Large Radial Force S 7/8-14 O-Ring Manifold 4-5/16- H Rhomb-Flange, Pilot 82.5x x6.35x31. Omit Standard Omit Blue AX Large Axial Force BMRS 18UNC, 7/16-UNF 1 H4 4-3/8-16 Square-Flange, Pilot 44.4x2.8 H1 Shaft 31., Splined Tooth 14-DP12/24 R Opposite B Black O No Case Drain 0 H5 4-M Square-Flange, Pilot 44.4x2.8 D Long Shaft 31., Splined Tooth 14-DP12/24 S Silver Grey F Free Running P 1/2-14 NPTF Manifold 4-5/ I Shaft 31., Parallel Key 7.96x7.96x31. LS Low Speed 18UNC, 7/16-UNF 315 T2 Cone Shaft 28.56, Parallel Key B5x5x14 3 P R PT(Rc)1/2 Manifold 4-M8, PT(Rc)1/4 J 34

35 BMH SERIES HYDRAULIC MOTOR BMH Series motors are medium speed, high torque motors designed on an internal gear design consisting of a rotor and stator. These motors are suitable for long operating periods at moderate pressures. Characteristic Features: Advanced manufacturing design of the Geroler gear set, which provide high starting torque, high efficiency and long life Motors have high pressure shaft seals which can be used in Parallel or Series Smooth running over the entire speed range Main Specifications Type BMH Geometric Displacement (cm 3 /rev.) Speed (rpm) Torque (Nm) Peak Output (kw) Pressure Drop (Bar) Peak Flow (L/min) Weight (kg) Type Inlet Pressure Return Pressure with Drain Line 1 1 BMH 0-0 (Bar) 0 0 Peak Continuous Pressure: value of operating motor continuously Intermittent Pressure: value of operating motor in 6 seconds per minute Peak Pressure: value of operating motor in 0.6 seconds per minute Technical data BMH with 35mm cylindrical, 1 ¼ in splined and 35mm tapered shaft 35

36 36 PERFORMANCE DATA BMH0 [3.2cm 3 /rev.] BMH2 [255.9cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) Flow (L/min) Flow (L/min)

37 PERFORMANCE DATA BMH315 [316.1cm 3 /rev.] BMH0 [6.4cm 3 /rev.] Pressure (Bar) Cont Pressure (Bar) Flow (L/min) Flow (L/min) Cont Torque (Nm) 593 Speed (rpm)

38 PERFORMANCE DATA BMH0 [0cm 3 /rev.] Pressure (Bar) Cont Flow (L/min) Cont Torque (Nm) 673 Speed (rpm)

39 BMH DIMENSIONS AND MOUNTING DATA 39

40 BMH SHAFT EXTENSIONS DIMENSIONS DATA

41 BMH SERIES HYDRAULIC MOTOR PERMISSIBLE SHAFT SEAL PRESSURE In applications without drain line, output shaft seal exceeds a bit of the pressure in the return line. When applications use the drain line, the pressure of output shaft seal equals the pressure in drain line. DIRECTION OF SHAFT ROTATION: STANDARD When facing shaft end of motor, shaft to rotate: Clockwise when Port A is pressurised Counter-clockwise Port B is pressurised STATUS OF THE SHAFT S RADIAL FORCE 41

42 ORDER INFORMATION Code Disp. Flange Output Shaft Port & Drain Port Rotation Direction Paint Unusual Function 1 B Shaft 32, Parallel Key x8x45 G1/2 Manifold Mount 4xM8, G1/4 D 0 M Shaft 35, Parallel Key x8x45 2 F Shaft 31., Splined Key 14-DP12/24 M22x1.5 Manifold Mount M 315 FD 4xM8, M14x1.5 Long Shaft 31., Splined Key 14-DP12/24 0 G Shaft 32, Parallel Key 7.96x7.96x No Paint Omit Standard Rhomb-Flange, Pilot 82.5x8 7/8-14 O-Ring Manifold Mount S Omit Standard Omit Blue O No Drain BMH 0 T1 Cone Shaft 35, Parallel Key B6x6x 4xM8, 7/16-UNF R Opposite B Black F Free Running Rhomb-Flange, Pilot 82.5x8 S Shaft 25.4, Parallel Key SAE 6B S Silver Grey LS Low Speed 1/2-14 NPFT Manifold Mount P 4xM8, 7/16-UNF R PT(Rc)1/2 Manifold Mount 4-M8,PT(Rc)1/4 42

43 BMJ SERIES HYDRAULIC MOTOR BMJ series motors have an advanced Geroller gear set, designed to accommodate high speed flow and pressure. These units have good stability at low speed, keeping high volumetric efficiency. Features Advanced design for the Geroller gear set, allowing low pressure start-up, provides smooth and reliable operation together with high efficiency Output shaft fitted with needle roller bearings permitting high axial and radial forces Advanced design in flow distribution automatically compensating resulting in high volume efficiency and long life, providing smooth and reliable operation Low leakage rate, accurate internal timing. Commutator rotates 6x faster than shaft output speed giving high precision and reduces life-cycle cost, maintaining high volume efficiencies and ability to run smoothly at low speed Specification Type Geometric Displacement (cm 3 /rev) Max Speed (rpm) Cont Int Max Torque (Nm) Cont Int Max Output (kw) Cont Int Max Pressure (Bar) Cont Int Peak Max Flow (L/min) Cont int Continuous Pressure: Max value of operating motor continuously Intermittent Pressure: Max value of operating motor in 6 seconds per minute Peak Pressure: Max value of operating motor in 0.6 seconds per minute 43

44 Dimensions Mounting Data BMJ SERIES HYDRAULIC MOTOR Wheel Mount Code: WS Ports A, B, 7/8 14 O-Ring Code: WD Ports A, B, G1/2 Code: WM Ports A, B, M22x1.5 Displacement (cm 3 /rev) L1 (mm) L (mm) Weight (kg) Side Load (dan) The bearing curve represents allowable bearing loads for an L bearing life at 3x 6 revolutions The maximum load curve is defined by bearing static load capacity. This curve should not be exceeded at any time including shock loads Distance from Mounting Face (mm) 44

45 ORDER INFORMATION BMJ Code Disp Flange, Pilot, Ports Output Shaft Rotation Direction Paint Unusually Function Cone-Shaft 35, Parallel Key B6x6x Omit WS WD WM Wheel- Flange, Pilot 82.55x7, Port 7/8-14 O-Ring Wheel- Flange, Pilot 82.55x7, Port G1/ Wheel- Flange, Pilot 82.55x7, Port M22x1.5 T1 T2 T3 T4 B Cone-Shaft 31., Woodruff Key 25.4x7.96 Cone-Shaft 31., Parallel Key 7.96x7.96x31. Cone-Shaft 31., Parallel Key 7.96x7.96x25.4 Cylindrical Shaft 32, Parallel Key x8x45 Omit R Standard Opposite 00 Omit B S No Paint Blue Black Silver Grey Omit Standard Shaft Extensions for Dimensions Data Motor Mounting Surface 45

46 VALVES FOR HYDRAULIC MOTORS SHUTTLE VALVE Code: VSEFMDSE Max Flow L/min Max Pressure 3 Bar V1 V2 ½ BSPP C3 ¼ BSPP CROSSLINE RELIEF WITH BRAKE RELEASE SHUTTLE VALVE Code: VSFMDISE / 1Y04B -1 Bar Adjustment Code: VSFMDISE / 1Z04B Bar Adjustment Max Flow Max Pressure V1 V2 C3 L/min 2 Bar ½ BSPP ¼ BSPP 46

47 VALVES FOR HYDRAULIC MOTORS ROTARY DIRECTIONAL VALVE WITH RELIEF Code: VIBFMDVS04B Max Flow 35L/min Max Pressure -1 Bar V1 V2 ½ BSPP DUAL OVERCENTRE VALVE WITH BRAKE RELEASE SHUTTLE VALVE Code: VB048FMDSECA12AX Pilot Ratio 7:1 Adjustment -1 Bar Max Flow L/min V1 V2 ½ BSPP C3 ¼ BSPP 47

48 48