MOMV SERIES HYDRAULIC MOTOR

Transcription

1 MOMV SERIES HYDRAULIC MOTOR MOMV series motor adapt the advanced Geroler gear set designed with disc distribution flow and high pressure.the unit can be supplied the individual variant in operating multifunction in accordance with requirement of applications. Characteristic features: * Advanced manufacturing devices for the Geroler gear set,which use low pressure of start-up, provide smooth and reliable operation and high efficiency. * The output shaft adapts in tapered roller bearings that permit high axial and radial forces. The case can offer capacities of high pressure and high torque in the wide of applications. * Advanced design in disc distrbution flow, which can automatically compensate in operating with high volume efficiency and long life, provide smooth and reliable operation. Main Specificaion Type MOMV 315 MOMV 400 MOMV 0 MOMV 630 MOMV 00 MOMV 00 Geometric displacement (cm 3 /rev.) Max. speed Max. torque Max. output Max. pressure drop Max. flow Weight (kg) (rpm) (N m) (kw) (L/min) peak peak * Continuous pressure :Max. value of operating motor continuously. * Intermittent pressure :Max. value of operating motor in 6 seconds per minute. * Peak pressure:max. value of operating motor in 0.6 second per minute.

2 Performance Data Torque (N m) 1340 Speed (rpm) 444 MOMV 315 [333cm 3 /rev.] MOMV 400 [41cm 3 /rev.] MOMV 0 [5cm 3 /rev.] MOMV 630 [666cm 3 /rev.]

3 Performance Data Torque (N m) 25 Speed (rpm) 5 MOMV 00 [01cm 3 /rev.] MOMV 00 [0cm 3 /rev.]

4 MOMV DIMINSIONS AND MOUNTING DATA Model MOMV315 MOMV400 MOMV0 MOMV630 MOMV00 MOMV00 L L L Flange 4 Drain portt Porting D M Flange W S G M5 S1 Model MOMVW315 MOMVW400 MOMVW0 MOMVW630 MOMVW00 MOMVW00 L L L Note:The thickness of the stator and rotor is the dimension of L1adding on 7mm. Content Code Mounting D (depth) M (depth) S (depth) G (depth) M5 (depth) S1 (depth) P(A,B) G1 () M33 x 2 () 1-5/-12UN() G1 () M33 x 2 () 1-5/-12UN() T G1/4 (12) M x 1.5 (12) /-UNF(12) G1/4 (12) M x 1.5 (12) 7/-UNF(12) C 4-M12 () 4-M12 ()

5 MOMV SHAFT EXTENSIONS DIMENSIONS DATA M12depth25 Shaft A: Cylindrical shaft ø Parallel key xx70 3/-UNC depth Shaft C: Cylindrical shaft ø57.15 Parallel key 12.7x12.7x57 3/-UNC depth M12depth25 Shaft B: Splined key -DP/ Shaft BD: Splined key -DP/ Shaft T: Cone-shaft ø60 Parallel key Bxx32 Tightening torque: 7±Nm Shaft T1: Cone-shaft ø57.2 Parallel key.30x.30x Tightening torque: 7±Nm

6 MOMV Series Hydraulic Motor Permissible shaft seal pressure In applications without drain line, output shaft seal exceeds a bit of the pressure in the return line. When applications use the drain line, the pressure of output shaft seal equals the pressure in drain line. Standard direction of shaft rotation: Standard When facing shaft end of motor,shaft to rotate: Clockwise when port "A" is pressurized. Counter-clockwise port "B" is pressurized. Axial and Radial forces MOMV The output shaft runs in tapered bearings that permit high axial and radial forces, Curve "A" shows max radial shaft load, Any shaft loads exceeding the values quoted in the curve will involve a risk of breakage, The two other curves apply to a B bearing life of 3000 hours at 0 RPM.

7 Order Information BMV Pos Code Displace Flange Output shaft Port and drain port ment Rotation Paint direction Unusually function W 4-Ø Square-flangeØ0, pilot Ø Ø Wheel-flange Ø2, pilot Ø0 A BD B C T T1 Shaft Ø, parllel key 70 Shaft Ø53., splined key -DP/ Shaft Ø53., splined key -DP/ Shaft Ø57.15, parllel key Cone shaft Ø60, parllel key B 32 Cone shaft Ø60, parllel key D M S G M5 S1 G1 Manifold 4 M12, G1/4 M33 2 Manifold 4 M12, M /-12UN, /-UNF G1,G1/4 M33 2, M /-12UN(), 7/-UNF(12) R Standard Opposite 00 B S No paint Blue Black Silver grey Standard Note:When the table is used, please fill the code of left rows in dash area and give us, which the code information is consists of construction, displacement, mounting flange, output shaft and ports. If the specification is not in the table or you have specific requirements, please contact us.