Disc Valve Motors Integral Cross Over Relief Valve Technical Manual 2000 Series

Transcription

1 Disc Valve Motors Integral Technical Manual 2000 Series

2 Introduction Eaton Char-Lynn, your proven low speed high torque motor supplier, now offers the Char-Lynn 2000 Series motor with our proven Eaton Vickers Screw-in Cartridge Valves integral to the motor. This compact and efficient package offers increased value and cost effectiveness to designing Eaton into your applications. Minimizing the use of hoses, tubing, and fittings will reduce production and assembly time significantly Series Geroler Element...9 Displacements Flow LPM [GPM]...75 [20] Cont.** 115 [30] Inter.* Speed...Up to 924 RPM Pressure Bar [PSI] [3000] Cont. 300 [4500] Inter. Torque Nm [lb-in] [7470] Cont. 930 [8225] Inter. ** Continuous (Cont.) Continuous rating, motor may be run continuously at these ratings. * Intermittent (Inter.) Intermittent operation, 10% of every minute. Features and Benefits Complete packaged system solution, single source for motor with relief valve capability Relief valves as close to the Geroler as possible, providing added protection. Eliminate leak points from in-line or bolt-on relief s Valves capable of full motor flow and full motor pressure. Provides added flexibility to system design by allowing motors to have individual relief valve settings. Simplifies assembly, purchasing, and system design requirements Applications Skid Steer Attachments Swing Motor Brush Cutters & Mowers Harvesting Equipment Directional Boring Any place pressure relief protection is optimal for system or motor performance and life Replacement cartridges can be obtained by ordering the Item Part Number as listed below. ITEM PART # ITEM DESC. RELIEF VALVE SETTING RV5A-10-F-0-35/ PSI RV5A-10-F-0-35/ PSI RV5A-10-F-0-35/ PSI RV5A-10-F-0-35/ PSI RV5A-10-F-0-35/ PSI RV5A-10-F-0-35/ PSI RV5A-10-F-0-35/ PSI 2 EATON Char-Lynn 2000 Series Disc Valve Motors C-MOLO-TM001-E September 2003

3 Standard Mount Motors * 65,3/62,7 [2.57/2.47] 10,2/7,8 [.40/.31] 1-1/4 inch Dia. Tapered Shaft * 1-1/4 inch Dia.Shaft 1 inch and 25 mm Dia.Shaft 52,4/49,7 [2.06/1.96] 56,7/54,3 [2.23/2.14] SAE 6 B * 56,7/54,3 * [2.23/2.14] 52,4/49,7 * * [2.06/1.96] 1-1/4 inch Dia. 32 mm Dia. Shaft 7/8 inch Dia. 65,8/63,5 [2.59/2.50] * 42,2/39,8 [1.66/1.57] * X Port B Y Max. 7/8-14 O-ring Staggered Ports, G 1/2 (BSP) Staggered Ports Case Drain 7/16-20 UNF-2B SAE O-ring Port Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW *Subtract 4,1/3,6 [.16/.14] when ordering motor with 4-bolt magneto flange 2X 93.0/ / / / Series Standard Motor with 7/8-14 O-Ring Staggered Ports or G1/2 (BSP) Staggered Ports DISPLACEMENT cm3/r [in3/r] 80 [ 4.9] 100 [ 6.2] 130 [ 8.0] 160 [ 9.6] 195 [11.9] 245 [14.9] 305 [18.7] 395 [24.0] 490 [29.8] Dim. X mm [in] 137,0 [ 5.40] 141,6 [ 5.58] 147,9 [ 5.83] 147,9 [ 5.83] 154,8 [ 6.10] 163,7 [ 6.45] 175,1 [ 6.90] 191,1 [ 7.53] 208,4 [ 8.21] Dim. Y mm [in] 184,5 [ 7.26] 189,0 [ 7.44] 195,4 [ 7.69] 195,4 [ 7.69] 202,2 [ 7.96] 211,1[ 8.31] 222,6 [ 8.76] 238,6 [ 9.39] 255,8[10.07] EATON Char-Lynn 2000 Series Disc Valve Motors C-MOLO-TM001-E September

4 Wheel Mount Motors 96,8/94,4 [3.81/3.72] 92,5/89,9 [3.64/3.54] 1 inch and 25 mm Dia.Shaft 1-1/4 inch Dia.Shaft 1-1/4 inch Dia. Tapered Shaft 105,5/102,8 [4.15/4.05] SAE 6 B 96,8/94,4 [3.81/3.72] 92,5/89,9 [3.64/3.54] 1-1/4 inch Dia. 32 mm Dia. Shaft 7/8 inch Dia. 106,0/103,6 [4.17/4.08] 82,4/79,9 [3.24/3.14] X 50,3/48,0 [1.98/1.89] Port B Y Max. 7/8-14 O-ring Staggered Ports, G 1/2 (BSP) Staggered Ports Case Drain 7/16-20 UNF-2B SAE O-ring Port Standard Rotation Viewed from Shaft End Port A Pressurized CW Port B Pressurized CCW 2X 93.0/ / / / Series Wheel Motor with 7/8-14 O-Ring Staggered Ports or G1/2 (BSP) Staggered Ports DISPLACEMENT cm3/r [in3/r] 80 [ 4.9] 100 [ 6.2] 130 [ 8.0] 160 [ 9.6] 195 [11.9] 245 [14.9] 305 [18.7] 395 [24.0] 490 [29.8] Dim. X mm [in] 96,9 [ 3.82] 101,4 [ 4.00] 107,8 [ 4.25] 107,8 [ 4.25] 114,6 [ 4.52] 123,5 [ 4.87] 135,0 [ 5.32] 151,0 [ 5.95] 168,2 [ 6.63] Dim. Y mm [in] 144,3 [ 5.68] 148,9 [ 5.86] 155,2[ 6.11] 155,2 [ 6.11] 162,1[ 6.38] 171,0 [ 6.73] 182,4 [ 7.18] 198,4 [ 7.81] 215,7[ 8.49] 4 EATON Char-Lynn 2000 Series Disc Valve Motors C-MOLO-TM001-E September 2003

5 Bearingless Motors Port for Internal or External Case Drain 157,5 [6.20] Max. (2) 101,60/101,47 [4.000/3.995] Pilot Dia. 127,0 [5.00] Dia. X 119,2 [4.69] Sq. Max. 13,85/13,33 [.545/.525] Dia. Thru (4) 14,22 [.560] Min. (4) 24,06/23,54 [.947/.927] Port B Y Max. 7/8-14 O-ring Staggered Ports, G 1/2 (BSP) Staggered Ports Case Drain 7/16-20 UNF-2B SAE O-ring Port 16,8/15,2 [.66/.60] 6.7/6,0 [.26/.24] Standard Rotation Viewed from Drive End Port A Pressurized CW Port B Pressurized CCW O-ring Seal Furnished with Motor C D E 2X 93.0/ / / /2.51 C 35,86 [1.412] Dia. K D 34,04 [1.340] Dia. E 81,0 [3.19 ] Min. Full Form Dia. F 86,1 [3.39 ] Max. G 62,10 [2.445] Full Form Dia. H 38,40 [1.512] Dia. J 43,7 [1.72 ] Da. K 25,91 [1.020] L 8,25 [.325] M 0,89 [.035] N 15 Mating Coupling Blank Eaton Part No L M H N F G 2000 Series Bearingless Motor with 7/8-14 O-Ring Staggered Ports or G1/2 (BSP) Staggered Ports For 2000 Series Bearingless Motor application information contact your Eaton representative (mating coupling blanks available from Eaton Hydraulics). Note: After machining blank, part must be hardend per Eaton specification. J DISPLACEMENT cm3/r [in3/r] 80 [ 4.9] 100 [ 6.2] 130 [ 8.0] 160 [ 9.6] 195 [11.9] 245 [14.9] 305 [18.7] 395 [24.0] 490 [29.8] Dim. X mm [in] 79,0 [ 3.11] 83,5 [ 3.29] 89,9 [ 3.54] 89,9 [ 3.54] 96,8 [ 3.81] 105,6 [ 4.16] 117,1 [ 4.61] 133,1 [ 5.24] 150,3 [ 5.92] Dim. Y mm [in] 126,8 [ 4.99] 131,4 [ 5.17] 137,7[ 5.42] 137,7 [ 5.42] 144,6[ 5.69] 153,5 [ 6.04] 164,9 [ 6.49] 180,9 [ 7.12] 198,2 [ 7.80] EATON Char-Lynn 2000 Series Disc Valve Motors C-MOLO-TM001-E September

6 Model Code Model Code for 2000 Series Motors The following 24-digit coding system has been developed to identify all of the configuration options for the 2000 Series motor Use this model code to specify a motor with the desired features. All 24-digits of the code must be present when ordering. You may want to photocopy the matrix below to ensure that each number is entered in the correct box. Sample Model Code: Model Code 2000 Series Disc Valve Motors M Nos Feature Code Description 1 Product Series M Motor 2, Series Series 4, 5 Displacement cm 3 /r [in 3 /r] [ 4.9] [ 6.2] [ 8.0] [ 9.6] [11.9] [14.9] [18.7] [24.0] [29.8] 6, 7 Mounting Flange AD 4 Bolt (Bearingless) 101,6 [4.00] Pilot Dia. and 13,59 [.535] Dia. Mounting Holes on 127,0 [5.00] Dia. B.C. AC 2 Bolt SAE A (Std.) 82,5 [3.25] Pilot Dia and 13,59 [.535] Dia. Mtg. Holes on 106,4 [4.19] Dia. B.C. AB 4 Bolt (Wheel) 108,0 [4.25] Pilot Dia. and 13,59 [.535] Dia. Mounting Holes on 147,6 [5.81] Dia. B.C. AH 4 Bolt (Standard) 82,5 [3.25] Pilot Dia. and 14,59 [.535] Dia. Mounting Holes on 106,4 [4.19] Dia. B.C. AJ 4 Bolt Magneto (Std.) 82,5 [3.25] Pilot Dia. and 13,59 [.535] Dia. Mtg. Holes on 106,4 [4.19] Dia. B.C. AF 2 Bolt SAE B (Std.) 101,6 [4.00] Pilot Dia. and 14,35 [.565] Dia. Mtg. Holes on 146,0 [5.75] Dia. B.C. AP 4 Bolt (wheel compatible for HAYES BRAKE) 107,9 [4.25] Pilot Dia. and 13,59 [.535] Dia. Mounting Holes on 147,6 [5.81] Dia. B.C. with Turned Down Housing to 88,9 [3.50] Dia. Nos Feature Code Description 8, 9 Output Shaft 00 Bearingless 01 1 inch Dia. Straight with Woodruff Key, 1/4-20 Threaded Hole and 38,4 [1.51] Max. Coupling Length /4 inch Dia. Straight with Straight Key, 3/8-16 Threaded Hole and 47,3 [1.86] Max. Coupling Length mm dia. Straight with Straight Key, M8 x 1,25-6H Threaded Hole and 56,4 [2.22] Max. Coupling Length /4 inch Dia. Splined 14 T, 3/8-16 Threaded Hole and 33,0 [1.30] Min. Full Spline Length and 45,5 [1.79] Max. Coupling Length /4 inch Dia. Tapered with Straight Key and Nut 05 1 inch SAE 6B Splined 6T, 1/4-20 Threaded Hole and 22,8 [.90] Min. Full Spline Length and 28,8 [1.13] Max. Coupling Length 07 7/8 inch Dia. Splined 13T, 15,2 [.60] Min. Full Spline Length and 30,8 [1.21] Max. Coupling Length /4 inch Dia. Straight with Straight Key, 3/8-16 Threaded Hole and Corrosion Resistant (seal area to shaft end) /4 inch Dia. Tapered with Straight Key and Nut, Corrosion Resistant (under seal area mm Dia. Straight with Straight Key, M8 x 1,25-6H Threaded Hole and 38,4 [1.51] Max. Coupling Length 6 EATON Char-Lynn 2000 Series Disc Valve Motors C-MOLO-TM001-E September 2003

7 Model Code Sample Model Code: Model Code 2000 Series Disc Valve Motors M Nos Feature Code Description 10, 11 Port Type AA 7/8-14 UNF 2B SAE O-ring (Staggered) AG G 1/2 BSP Straight Thread ports (Staggered) AB Manifold Mount with 3/8-16 UNC Mounting Threads (3) AE Manifold Mount with M10 x 1,5-6H Mounting Threads (3) AD 7/8-14 UNF 2B SAE O-ring (End Ports) AF 1 1/16-12 UN-2B O-ring ports (Positioned 180 Apart) 12, 13 Case Flow (Shuttles available with port code AA or AD 01 7/16-20 UNF 2B SAE O-ring (Case Drain) 02 G 1/4 (BSP) straight thread port (Case Drain) 04 Shuttle Valve with 7/16-20 UNF 2B SAE O-ring (Case Drain) 05 Shuttle Valve with G 1/4 (BSP) straight thread port (Case Drain) 14 Low Pressure Relief (LPR available with a combination of case flow code 04 or 05 and port code AA or AD 0 None A 4,5 bar [65 psi] B 15,2 bar [220 psi] C 20,7 bar [300 psi] 15, 16 Valve Option 00 None 17, 18 Accessories 00 None AA Seal Guard AB Speed Sensor (Std. With Weatherpack shroud connector) AH Speed Sensor (Std. With M12 connector) AL Quadrature Speed Sensor Version 2 with M12 Nos Feature Code Description 19, 20 Special Features (Hardware) 00 None 01 Viton Seals 10 Viton Shaft Seal bar [1500 psi] Internal bar [1750 psi] Internal bar [2000 psi] Internal bar [2250 psi] Internal bar [2500 psi] Internal bar [2750 psi] Internal bar [3000 psi] Internal 21 Special Features (Assembly) 0 None A Flange Rotated 90 B Reverse Rotation 22 Paint/Special Packaging 0 No Paint A Painted Low Gloss Black B Corrosion Protected 23 Eaton Assigned Code when Applicable 0 Assigned Code 24 Eaton Assigned Design Code 0 Assigned Design Code EATON Char-Lynn 2000 Series Disc Valve Motors C-MOLO-TM001-E September

8 Eaton Lone Oak Road Eden Prairie, MN USA Tel: Fax: Eaton 20 Rosamond Road Footscray Victoria 3011 Australia Tel: (61) Fax: (61) Eaton Eaton Fluid Power GmbH Dr.-Reckeweg-Str. 1 D Baden-Baden, Germany Tel: +49 (0) Fax: +49 (0) Eaton Corporation All Rights Reserved Printed in USA Document No. C-MOLO-TM001-E September 2003