Mold Design. 7. Mold Design Runner & Gate. Bong-Kee Lee School of Mechanical Engineering Chonnam National University

Size: px
Start display at page:

Download "Mold Design. 7. Mold Design Runner & Gate. Bong-Kee Lee School of Mechanical Engineering Chonnam National University"

Transcription

1 7. Runner & Gate Bong-Kee Lee Chonnam National University Delivery System Delivery System (Feed System) sprue (for a cold runner mold) cold slug well (for a cold runner mold) runner gate basic feed system

2 Delivery System Sprue should be tapered 3~5 inclusive angle being pulled out of the mold more easily should also be highly polished in the line of draw to assist withdrawal to induce more efficient flow diameter at the narrow end should be larger than the machine cylinder nozzle opening Delivery System Cold Slug Well to trap the cooler advancing front of the melt, thus permitting hotter melt to reach the cavities and gates snatch or pull pin or sucker pin underneath it to positively pull the sprue out of the sprue bush diameter design based on the diameter of the sprue where it meets the runner to avoid any obstruction to the melt flow

3 Delivery System Cold Slug Well for ejection pin systems with a hardened bush to minimize wear the least desirable one due to large mass and long cooling time capture the colder advancing front well normally preferred one sometimes tends to hang up, but preferred for brittle materials Delivery System Cold Slug Well for stripper plate ejection

4 purpose of runner to transport the melt from the sprue to the gates basic parameters for runner geometry cross-sectional shape diameter cavity layout cross-sectional shape full round cross-section: the most efficient design trapezoidal one: for three-plate molds semi-circular or half round one: severely restricts flow although frequently used square and rectangular ones: should never be used formation of dead zones in the runner design rheologically inefficient and wasteful on material and energy

5 cross-sectional shape diameter (size of runners) based on the thickness of the molding wall section should be large enough to provide adequate pressure to all the cavities no packing pressure shortfall and adequate control over the molding conditions alternative method: based on an appropriate pressure drop along the length of the runner

6 cavity layout beneath runner intersections cold slug well for improving melt flow: length of cold slug well ~ runner diameter ejection pin variation of runner diameters cavity layout incorrect design correct design incorrect design correct design

7 design rules runners must be designed to fill the cavity rapidly runner design must provide for easy ejection and easy removal (de-gating) from the molded part for a multi-cavity system, balanced runner layout is preferred for the best uniformity and part quality runner balancing may be achieved by changing the runner size and length changing the gate dimensions may seem to give a reasonably balanced fill but this will affect the gate freeze-off time smaller runner sizes are preferred to larger ones to minimize scrap volume and generate viscous heating high barrel temperature may cause material degradation design rules (continued) the cross-sectional area of the runner should not be smaller than that of the sprue, to permit rapid, unaltered flow to the gates the diameter of the branch runner should be smaller than that of the main runner as more economical way D dn 1/3 :(main runner diameter) (branch runner diameter)(number of branch runners) the depth of a trapezoidal runner is approximately equal to its width with a 5~15 taper or draft angle on each sidewall the minimum recommended runner diameter for most materials is 1.5mm the runner surface and sprue should be polished 1/ 3

8 design rules (continued) it is desirable to have multiple sprue pullers and ejection locations in extended runner systems the selection of a cold runner diameter should be based on standard machine tool cutter sizes for hot runner systems, it is advisable to consult the suppliers for availability and recommendations for the correct manifold and drops calculation of runner length (assumption) maximum pressure drop along the length of the runner ~ 70MPa (50MPa for filled material in most cases) safe working figure with which to calculate runner lengths 4Q 3 r -1 :shear rate[s ] 3 Q :flow rate[m /s] r : runner radius[m] : viscosity at melt temperature[pa s] P : pressure drop [MPa] :shear stress [MPa] L : runner length [m] 2 L P r

9 calculation of runner length (example) polycarbonate using a melt temperature of 310 C (viscosity of 1000Pa s) and a flow rate through the runner of 2.85cm 3 /s runner length of 120mm and diameter of 4mm 4Q 2 L P 3 r r 6 4Q [s ] r [MPa] 2 L P 3 r [MPa] Runnerless Molding runnerless molding usually includes sprueless molding basic antechamber designs: melt flows through an insulated cold slug well heated hot sprue bushes or nozzles: internal or external heating insulated runner systems insulated semi-insulated hot runner systems

10 Runnerless Molding typical antechamber design semi-insulated runner design Hot s advantages over cold runner molds no runner system to be removed from the mold shorter cycle time with no cold runner to be cooled reduced mold opening stroke reduced (or eliminated) cost for storing and regrinding runners lowered risk of material contamination gates may be balanced more easily lowered injection pressure using the larger runner diameters ~ greater number of impressions, utilization of smaller machines smaller shot weight ~ reduced metering times and injection times

11 Hot s disadvantages significantly more expensive 24-hour operation is required for maximum economic production heat-sensitive materials may be difficult to process gate blockages can be time-consuming and expensive to remedy Hot s hot runner manifold separated unit carrying the runner and nozzle gating systems insulated from the main body of the mold

12 Hot s hot runner manifold nozzles and gate bushes pin and edge gating, valve gating, thermal sealing heating with band, coil, cartridge, tubular heaters temperature sensing and control thermal expansion and efficiency issues Hot s insulation water cooling in the core support and guide of stripper plate ejection

13 Hot s hybrid hot runner/cold runner system flash gate ~ uniform melt flow efficient air venting through a parting line (cf. multi-point gating ~ complex flow) evenly spread force due to the molded part off-centered hot runner manifold large number of cooling channels mold design for a suitcase half Gate small opening (or orifice) through which the polymer melt enters the cavity gate design: gate type, dimensions, and locations part geometry (wall thickness, etc.) part specifications (appearance, tolerances, etc.) material used fillers used cycle time de-gating requirements

14 Gate number of gate for the cavity single gate multiple gates ~ if the length of melt flow exceeds practical limits weld and meld lines cross-section of the gate typically smaller than that of the runner and the part related to the de-gating (separation from the molded part), the material freezing off (during the post-filling stage), and the viscous heating Basic Gate Terminology

15 Gate Location should be selected in such a way that rapid and uniform mold filling is ensured and weld/meld lines and air vents are positioned properly should be positioned away from load-bearing areas because the high melt pressure and high velocity of flowing material causes the area near the gate to be highly stressed Common Types of Gates direct or sprue gate tab gate edge or side gate overlap gate direct feed of material into the cavity rapidly and with minimum pressure drop the gate has to be trimmed off and a large gate witness is left on the part typically used for flat, thin parts to reduce the shear stress in the cavity high shear stress is confined to the tab which is trimmed off after molding located at the parting line of the mold and fills the cavity from the side, top or bottom of the part similar to the edge gate except the overlaps the wall or surfaces

16 Common Types of Gates fan gate disc or diaphragm gate ring gate spoke or spider gate similar to a wide edge gate with a variable thickness permits rapid filling of large parts or fragile mold sections through the large entry area creates a uniform flow front frequently used for gating cylindrical or round parts that have an open inside diameter for concentricity and unacceptable weld line for gating round or cylindrical parts material flows freely around the core before it flows down as a uniform front to fill the cavity a four point or cross gate for tubular parts and offers much easier degating than the ring gate possibility of weld lines and out of roundness Common Types of Gates film or flash gate hot probe gate pin gate submarine or tunnel gate similar to a ring gate but is used for flat, straight parts consists of a straight runner and a gate land across either the entire length or width of the cavity or a portion of it normally used to deliver material directly into the cavity through heated runners resulting in runnerless moldings generally used in three plate and hot runner molds to permit rapid gate freeze off and easy de-gating mainly used in two plate molds enables automatic degating of the part from the runner during the ejection stage

17 Common Types of Gates sprue gate tab gate fan gate flash gate Common Types of Gates ring gate disc gate pin gate submarine gate

18 De-gating manually trimmed gates automatically trimmed gates for two-plate molds submarine gates De-gating hook gates gating onto the top surface or side of a component is not acceptable difficult and expensive to make material must be flexible C: cavity insert B: separate additional insert cross-section of the gate must decrease toward the parts A: extended runner to enable the full length of the gate to be withdrawn from the mold

19 Design Rules gate design should deliver a rapid, uniform and preferably unidirectional mold filling pattern gate location should allow the air present in the cavity to escape during the filling stage if the gate location is likely to cause weld or meld lines, it should be positioned so that these will occur at appropriate positions to preserve part quality and appearance gate location and size should avoid the possibility of jetting Design Rules freeze-off time at the gate should ensure maximum cavity packing time and also prevent back flow gate location should be at the thickest area of the part gate length should be as short as possible to avoid an excessive pressure drop across the gate gate thickness is normally 50~80% of the gated wall section thickness fiber-filled materials require larger gates to minimize breakage of the fibers

20 Flow Analysis direct sprue gate (center-gated design) ~ part warpage double edge gate ~ weld line at the center of the part single edge gate ~ unidirectional filling pattern with uniform molecular and fiber orientation Gate Sizing length : should be as short as possible diameter rough approximation 4Q r 3 r flow analysis using computer software empirical approximation d NC 4 A 3 4Q A : total surface area of the product [mm wall thickness [mm] C N: 0.6 (PE, PS); 0.7 (PC, PP, acetal); 0.8 (Nylon); 0.9 (PVC) 2 ]

Feed System Design OBJECTIVES IN FEED SYSTEM DESIGN DPT 321 INJECTION MOLD DESIGN COURSE CONTENT & COURSE OUTCOMES. Introduction of Feed System

Feed System Design OBJECTIVES IN FEED SYSTEM DESIGN DPT 321 INJECTION MOLD DESIGN COURSE CONTENT & COURSE OUTCOMES. Introduction of Feed System COURSE CONTENT & COURSE OUTCOMES School of Manufacturing Engineering COURSE CONTENT Chapter 5: Gate, Runner and Venting Design DESCRIBE and EXPLAIN the type of gates, and gate selection. DESCRIBE and EXPLAIN

More information

Autodesk Moldflow Communicator Modeling

Autodesk Moldflow Communicator Modeling Autodesk Moldflow Communicator 2012 Modeling Revision 1, 23 March 2011. Contents Chapter 1 Modeling............................................. 1 Recommended modeling details................................

More information

INJECTION MOULDING TROUBLESHOOTING GUIDE

INJECTION MOULDING TROUBLESHOOTING GUIDE Page : 1 / 12 BLACK SPECKS OR STREAKS Excessive residence time in the barrel Hang-up of Molten material in the injection barrel or runner system Contamination of the injection barrel Degradation due to

More information

Machine nozzle with needle shut-off type HP pneumatically or hydraulically controlled

Machine nozzle with needle shut-off type HP pneumatically or hydraulically controlled Machine nozzle with needle shut-off type HP pneumatically or hydraulically controlled Applications: Thermoplastics (not applicable for PVC) Shut-off mechanism: Needle shut-off with integrated 2-way actuator

More information

Machine nozzle with needle shut-off type HP pneumatically or hydraulically controlled. Needle shut-off

Machine nozzle with needle shut-off type HP pneumatically or hydraulically controlled. Needle shut-off Machine nozzle with needle shut-off type HP pneumatically or hydraulically controlled Needle shut-off Applications: Thermoplastics (not applicable for PVC) Shut-off mechanism: Needle shut-off with integrated

More information

Promix Solutions trust the leader. Static Mixers Solutions for Injection Molding

Promix Solutions trust the leader. Static Mixers Solutions for Injection Molding Promix Solutions trust the leader Static Mixers Solutions for Injection Molding Your partner in the plastics processing industry Founded in 2012 as a spin-off of Sulzer Chemtech Subsidiaries in Winterthur,

More information

COOLPOLY THERMALLY CONDUCTIVE PLASTICS TCP. Design Manual

COOLPOLY THERMALLY CONDUCTIVE PLASTICS TCP. Design Manual COOLPOLY THERMALLY CONDUCTIVE PLASTICS TCP Design Manual 1 Table of Contents 1 Introduction to CoolPoly TCP 3 Thermally Conductive Plastics 3 2 Celanese Capabilities 4 Background 4 Design 4 Computer Aided

More information

Hot Sprue Bushings Products/Technical Guide

Hot Sprue Bushings Products/Technical Guide Hot Sprue Bushings Products/Technical Guide USB8 And SB8 Hot Sprue Bushings Notes 1. Cold bushing length must allow for thermal expansion to fit specified mold length. 2. For special "A" length order next

More information

Hot Runner Guide Layout and Design

Hot Runner Guide Layout and Design H O T R U N N E R Layout and Design Stabilize your Process CAT-14-0001_EN-Rev05 EN 11/2017 T E C H N O L O G Y Layout and Design The purpose of this The - Layout and Design is intended to help everyone

More information

Hot Runners and Temperature Controllers

Hot Runners and Temperature Controllers Hot Runners and Temperature Controllers Better parts, faster cycles Benefits Complete tooling solutions Application specific solutions Pristine gate quality Fastest cycles Fast color change Accurate, reliable

More information

smart hot runner solutions

smart hot runner solutions Mould Design Recommendations for Hot Runner Applications smart hot runner solutions www.mastip.com Contents Mould Design Recommendations pg 3 4 5 6 6 6 8 9 11 12 13 Contents Introduction 1.0 Plate Requirements

More information

TOOLING STANDARDS AND MACHINE SPECIFICATIONS DOCUMENT #END 001 REVISION LEVEL: A9

TOOLING STANDARDS AND MACHINE SPECIFICATIONS DOCUMENT #END 001 REVISION LEVEL: A9 1 P.O. Box 447 160 E Pond, Romeo, MI. 48065 Phone (586) 752-4527 Fax (586) 752-0896 TOOLING STANDARDS AND MACHINE SPECIFICATIONS DOCUMENT #END 001 REVISION LEVEL: A9 DISTRIBUTION LIST OF TOOLING STANDARDS

More information

auxiliary technologies advanced molding applications technical services overview Accu-Valve for optimum part quality

auxiliary technologies advanced molding applications technical services overview Accu-Valve for optimum part quality overview Recognized as the hot runner technology leader for over 4 decades, Mold-Masters has developed the widest range of system solutions that go beyond the usual day to day requirements. Our MasterSOLUTION

More information

Band Heaters Maxiband Heaters Maxiband The Most Sought After Band Heater

Band Heaters Maxiband Heaters Maxiband The Most Sought After Band Heater Band Heaters Maxiband Heaters Maxiband The Most Sought After Band Heater A B C D E F General purpose terminal box offers excellent protection to the exposed terminals. To simplify electrical wiring, the

More information

Hot Runner Solutions for Technical Moulding. An Introduction to Mastip Technology.

Hot Runner Solutions for Technical Moulding. An Introduction to Mastip Technology. Hot Runner Solutions for Technical Moulding An Introduction to Mastip Technology www.mastip.com Company Profile Mastip is a leading supplier of innovative hot runner solutions to the global plastic injection

More information

SEEV-A HD High-Duty, Advanced All-Electric Series. 8 model sizes from 247 to 562 U.S. tons

SEEV-A HD High-Duty, Advanced All-Electric Series. 8 model sizes from 247 to 562 U.S. tons SEEV-A HD High-Duty, Advanced All-Electric Series 8 model sizes from 247 to 562 U.S. tons SEEV-A HD Series Advanced, High-Duty All-Electrics 8 model sizes from 247 to 562 U.S. tons With the new SEEV-A

More information

Gated and assembled in one moulding cycle

Gated and assembled in one moulding cycle Customer information from EWIKON Heißkanalsysteme GmbH Gated and assembled in one moulding cycle Tailored hot runner solution for a demanding -component mould concept Pages - 5 Processing of sensitive

More information

MAGNA T SERVO. 500 to 5,500 kn

MAGNA T SERVO. 500 to 5,500 kn MAGNA T SERVO 500 to 5,500 kn A NEW STANDARD IN TOGGLE TECHNOLOGY Energy Efficient, Rugged & Reliable, Precise & Consistent, Versatile & User Friendly MAGNA T SERVO TOGGLE INJECTION MOLDING MACHINE Durable

More information

International Journal on Emerging Technologies 3(2): (2012) ISSN No. (Print) : ISSN No. (Online) :

International Journal on Emerging Technologies 3(2): (2012) ISSN No. (Print) : ISSN No. (Online) : e t International Journal on Emerging Technologies 3(2): 93-100(2012) ISSN No. (Print) : 0975-8364 ISSN No. (Online) : 2249-3255 Feature ibrary of Gating System for a Die-Casting Die Chandan Deep Singh

More information

Classic & Threaded Nozzle Selection Guide...J4. Emerald Ceramic Technology...J8. Emerald Classic Nozzle...J6. Emerald Hot Runner Systems...

Classic & Threaded Nozzle Selection Guide...J4. Emerald Ceramic Technology...J8. Emerald Classic Nozzle...J6. Emerald Hot Runner Systems... J1 Classic & Threaded Nozzle Selection Guide...J4 Emerald Ceramic Technology...J8 Emerald Classic Nozzle...J6 Emerald Hot Runner Systems...J3 Emerald Threaded Nozzle...J7 Policosmetic Hot Runner Systems...J9

More information

Revision 9 January 9, 2019

Revision 9 January 9, 2019 Kalsi Seals Handbook Chapter C5 Enhanced Lubrication Kalsi Seals Revision 9 January 9, 2019 Individual chapters of the Kalsi Seals Handbook are periodically updated. To determine if a newer revision of

More information

FlowControl. Smart & Effective. Stabilize your Process

FlowControl. Smart & Effective. Stabilize your Process FlowControl Smart & Effective Stabilize your Process FlowControl Demanding visual appearance with precise dimensional stability Gloss level, evenly textured surfaces, color uniformity and aesthetics, are

More information

Plasson Solutions for Large Bore Pipes

Plasson Solutions for Large Bore Pipes Plasson Solutions for Large Bore Pipes Innovative Design Simpler Installation Plasson Quality and Reliability Plasson Large Bore PE Fitting Systems The use of PE has become well established in pipeline

More information

TH series Premium hydraulic injection molding machine

TH series Premium hydraulic injection molding machine TH series Premium hydraulic injection molding machine Developed at WOOJIN PLAIMM's R&D center in Austria, TH series is designed to deliver the familiarity in design and performance of its European counterparts.

More information

Mounting Overlap Shield. Face Clamps. Gap. Seat Depth. Lead In Chamfer. Loose Fit.

Mounting Overlap Shield. Face Clamps. Gap. Seat Depth. Lead In Chamfer. Loose Fit. Mounting Introduction: Reali-Slim thin section ball bearings have a crosssection thickness that is much thinner than standard bearings of the same diameter, and are therefore more sensitive to shaft and

More information

Haitian Saturn Series

Haitian Saturn Series PLASTICS MACHINERY Haitian Saturn Series HT 07001_GB Haitian International Co., Ltd Unit 1105 Metroplaza tower 2, 223 Hing Fong Road Kwai Fong N. T haitian@mail.haitian.com Haitian Partner: NINGBO HAITIAN

More information

PNEUMATICALLY ACTUATED 2-WAY

PNEUMATICALLY ACTUATED 2-WAY 482 DN 25-65 The 482 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic efficiency by increasing

More information

Computer-Assisted Induction Aluminum

Computer-Assisted Induction Aluminum Home Computer-Assisted Induction Aluminum Brazing November 11, 2003 Coupled electromagnetic and thermal computer simulation provides a sufficient basis for process optimization and quality improvement

More information

MODULAR MELT FLOW: The First Step: Melt Flow Index (Weight Method) According to ASTM D 1238, ISO 1133 Method A and other equivalents

MODULAR MELT FLOW: The First Step: Melt Flow Index (Weight Method) According to ASTM D 1238, ISO 1133 Method A and other equivalents MODULAR MELT FLOW: Plug in as you go: if you need more features as your business grows, simply add them on! For instance: digital encoder for Method B, weight lifting device for automation, automatic cutting

More information

A pump is a machine used to move liquid through a piping system and to raise the pressure of the liquid.

A pump is a machine used to move liquid through a piping system and to raise the pressure of the liquid. What is a pump A pump is a machine used to move liquid through a piping system and to raise the pressure of the liquid. Why increase a liquid s pressure? Static elevation a liquid s pressure must be increased

More information

SECTION A: INTRODUCTION

SECTION A: INTRODUCTION SECTION A: INTRODUCTION Overview of the Injected Metal Assembly (IMA ) process Fishertech s Injected Metal Assembly process combines assembly techniques with specialized die casting technology to increase

More information

VISHU SHAH TEL : D West Lambert Road FAX : GRIPPER

VISHU SHAH TEL : D West Lambert Road FAX : GRIPPER CONSULTEK CONSULTING FOR PLASTICS INDUSTRY www.consultekusa.com www.theplasticsconsultant.com VISHU SHAH TEL : 714-674-1981 460-D West Lambert Road FAX : 714-674-1981 Brea, CA 92821 vishu@consultekusa.com

More information

1. Clean the cylinder.

1. Clean the cylinder. TPE General Since the production process consists of a large number of complex operations, sometimes problems may arise. TPE is a living material, which ages and is affected by its environment. Your Dryflex,

More information

Machine bolt shut-off nozzle type BHP pneumatically or hydraulically controlled

Machine bolt shut-off nozzle type BHP pneumatically or hydraulically controlled Machine bolt shut-off nozzle type BHP pneumatically or hydraulically controlled Applications: Thermoplastics (not applicable for PVC) Shut-off mechanism: Bolt shut-off with integrated 2-way actuator pneumatically

More information

Engel Injection Molding Machine VERTICAL CLAMP INSERT 330V/90 WP US. Data Sheet INSERT 330V/90 WP US - VERTICAL CLAMP / VERTICAL INJECTION

Engel Injection Molding Machine VERTICAL CLAMP INSERT 330V/90 WP US. Data Sheet INSERT 330V/90 WP US - VERTICAL CLAMP / VERTICAL INJECTION Engel Injection Molding Machine INSERT 330V/90 WP US - VERTICAL CLAMP / VERTICAL INJECTION CLAMP Clamp force US tons 90 Clamp opening force US tons 3.0 Clamp stroke (max.) inches 13.78 Mold height (min

More information

Table of Contents 2.0 COOLFLEX CLX. 2.0 Table of Contents

Table of Contents 2.0 COOLFLEX CLX. 2.0 Table of Contents Table of Contents CLX 2.0 2.0 Table of Contents 2.1 System description 2.100 System description (general) 2.105 System description (data) 2.115 range, DN 20 - DN 125 / SDR 11 (coils) 2.2 Planning, design

More information

Kaydon white paper. The importance of properly mounting thin section bearings. an SKF Group brand. by Rob Roos, Senior Product Engineer

Kaydon white paper. The importance of properly mounting thin section bearings. an SKF Group brand. by Rob Roos, Senior Product Engineer The importance of properly mounting thin section by Rob Roos, Senior Product Engineer an SKF Group brand Figure 1 Radial Load Reversing Thrust Overturning Moment Thin section ball have a much thinner cross-section

More information

CATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL.

CATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. CATALOG Actuated Diaphragm Valve DN 15-100 PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. TABLE OF CONTENTS Type 186 - DN 12-15 (MA 10) 04 General information - Technical specification 04 Sectional

More information

D-M-E Hot Runner Systems

D-M-E Hot Runner Systems D-M-E Hot Runner Systems The best solution for precision thermoplastic micromolding Engineered for the challenges of tight pitch molding The D-M-E Stellar Hot Runner System brings high performance, exacting

More information

Module 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions

Module 3: Influence of Engine Design and Operating Parameters on Emissions Lecture 14:Effect of SI Engine Design and Operating Variables on Emissions Module 3: Influence of Engine Design and Operating Parameters on Emissions Effect of SI Engine Design and Operating Variables on Emissions The Lecture Contains: SI Engine Variables and Emissions Compression

More information

Part C: Electronics Cooling Methods in Industry

Part C: Electronics Cooling Methods in Industry Part C: Electronics Cooling Methods in Industry Indicative Contents Heat Sinks Heat Pipes Heat Pipes in Electronics Cooling (1) Heat Pipes in Electronics Cooling (2) Thermoelectric Cooling Immersion Cooling

More information

What is BF? Tubes Sprockets Grooves Coatings & Platings Axles Axle Machining Bearings Roller Assembly Tapers Formed Tubes Special Features

What is BF? Tubes Sprockets Grooves Coatings & Platings Axles Axle Machining Bearings Roller Assembly Tapers Formed Tubes Special Features ROLLERmANUAL Table of Contents What is BF? Tubes Sprockets Grooves Coatings & Platings Axles Axle Machining Bearings Roller Assembly Tapers Formed Tubes Special Features Applications Questions to Ask 2

More information

Chapter 3 Grouting Equipment and Methods

Chapter 3 Grouting Equipment and Methods Chapter 3 Grouting Equipment and Methods 3-1. Grout-Mixing Equipment a. Mixing and blending tanks. Mixing and blending tanks (Figure 3-1) for chemical-grouting operations should be constructed of materials

More information

Broad multiplex outlet BF-V...

Broad multiplex outlet BF-V... Air distribution systems Broad multiplex outlet BF-V... DS 40 E 04.0 Technical Selection Preliminary remarks In many applications in the commercial sector, supply air is discharged via simple grilles built

More information

System Selection Guide

System Selection Guide Your Complete Hot Runner Configuration Guide www.mastip.com We make things better 2 Contents Contents Standard Hot Runner Configuration Hot Runner System Overview Selection Overview zzle Range and Series

More information

Thermoelectric Module Installation Guidance

Thermoelectric Module Installation Guidance Thermoelectric Module Installation Guidance Introduction The aim of this document is to describe the process for mounting a thermoelectric module for use in a system. Considerations for mounting cooler

More information

COMPUTER AIDED FEEDING SYSTEM DESIGN FOR PRESSURE DIECASTING

COMPUTER AIDED FEEDING SYSTEM DESIGN FOR PRESSURE DIECASTING COMPUTER AIDED FEEDING SYSTEM DESIGN FOR PRESSURE DIECASTING Dissertation submitted in the partial fulfillment of the requirements for the degree of Master of Technology In Mechanical Engineering Submitted

More information

Dielectric Oil and Flushing for Ram EDM

Dielectric Oil and Flushing for Ram EDM 12 Dielectric Oil and Flushing for Ram EDM 171 Dielectric Oil Ram EDM uses oil for its dielectric fluid. Dielectric oil performs three important functions for ram EDM. See Figure 12:1. 1. The oil forms

More information

Why bigger isn t always better: the case for thin section bearings

Why bigger isn t always better: the case for thin section bearings White Paper Why bigger isn t always better: the case for thin section bearings Richard Burgess, Les Miller and David VanLangevelde, Kaydon Bearings Typical applications Thin section bearings have proven

More information

Cosmetic sealing. paint shop. Atlas Copco s SCA product line provides high-quality cosmetic sealing solutions

Cosmetic sealing. paint shop. Atlas Copco s SCA product line provides high-quality cosmetic sealing solutions Cosmetic sealing in Cosmetic paint shop sealing Atlas Copco s SCA product line provides high-quality cosmetic sealing solutions Meeting highest demands in paint shop Sealing and sound dampening applications

More information

The ROBUST Performer

The ROBUST Performer 80 to 910 Ton The ROBUST Performer Energy Efficient Generous Specifications Robust & Reliable User Friendly Control The ROBUST Performer 3 Large Ram Diameter Provides Uniform Force Distribution across

More information

Table of Contents. EIGERFLEX -Clima. 2.0 Table of Contents

Table of Contents. EIGERFLEX -Clima. 2.0 Table of Contents 2.0 Table of Contents 2.0 Table of Contents 2.1 System description 2.100 System description (general) 2.105 System description (data) 2.115 -Clima range, DN 20 - DN 125 / SDR 11 (coils) 2.120 -Clima range,

More information

APPLICATION NOTE. Package Considerations. Board Mounting Considerations. Littelfuse.com

APPLICATION NOTE. Package Considerations. Board Mounting Considerations. Littelfuse.com package. Compared to products in plastic molded packages, the SESD device offers a significant performance-per-boardarea advantage. The SESD package and a dimensional view of the package bottom are shown

More information

AutoJet. Highly efficient method of applying lubricants and corrosion protection fluids

AutoJet. Highly efficient method of applying lubricants and corrosion protection fluids AutoJet Lubrication Systems Highly efficient method of applying lubricants and corrosion protection fluids Functional Differences Nozzles for Type P400: Type L210 For low-viscosity media Type P400 For

More information

- New Superpave Performance Graded Specification. Asphalt Cements

- New Superpave Performance Graded Specification. Asphalt Cements - New Superpave Performance Graded Specification Asphalt Cements 1 PG Specifications Fundamental properties related to pavement performance Environmental factors In-service & construction temperatures

More information

Feeding Concepts, Inc Vibratory Feeding Equipment Troubleshooting Manual

Feeding Concepts, Inc Vibratory Feeding Equipment Troubleshooting Manual Feeding Concepts, Inc Vibratory Feeding Equipment Troubleshooting Manual Provided by: Feeding Concepts, Inc. 15235 Herriman Blvd. Noblesville, IN 46060 P- 317.773.2040 F- 317.773.1494 www.feedingconcepts.com

More information

Module 7: Cooling System Components

Module 7: Cooling System Components  Â  Basic Cooling System Components Radiators Common Types of Radiators Coolant Hoses Water Pumps Centrifugal Force Types of Drives for Water Pumps Types of Drive Belts Basic Cooling System Components

More information

White paper More productivity with optimally cushioned pneumatic cylinders

White paper More productivity with optimally cushioned pneumatic cylinders White paper More productivity with optimally cushioned pneumatic cylinders With the right end-position cushioning, you can significantly increase the efficiency of your entire pneumatic system. When used

More information

YUDO SINGLE VALVE NOZZLE SERIES III V E R. N O M N S V E N O

YUDO SINGLE VALVE NOZZLE SERIES III V E R. N O M N S V E N O SINGLE VALVE III Instruction Manual YUDO SINGLE VALVE NOZZLE SERIES III V E R. N O. 0 2 0 9 M N S V E N O Greetings Thank you for using YUDO Single Valve III System. YUDO fabricated Single Valve III System

More information

Tips and tricks from the experts

Tips and tricks from the experts Tips and tricks from the experts Common errors when using rotary vane pumps and how to avoid them The ideal vacuum solution at the best price is very often the main decision criterion. But this fact poses

More information

SE-EV Advanced All-Electric Series

SE-EV Advanced All-Electric Series SE-EV Advanced All-Electric Series SE-EV Series Advanced All-Electrics Model sizes: 56, 84, 112, 146 and 202 U.S. tons New NC-10 control with Z-molding capabilities plus improved ease-of-use, processing

More information

This is trial version

This is trial version Z-Standards Contents (Alphabetical order, terms partly according to DIN 16750) A All dimensions shown in this catalogue are specified in mm, given tolerances refer to an ambient temperature of 20 C Prod.-No.

More information

PROVISIONAL PATENT APPLICATION INVENTORS: RICHARD E. AHO CAVITATION ENGINE

PROVISIONAL PATENT APPLICATION INVENTORS: RICHARD E. AHO CAVITATION ENGINE PROVISIONAL PATENT APPLICATION INVENTORS: RICHARD E. AHO WILLIAM WALTER MEE FOR CAVITATION ENGINE Richard E. Aho 4170 N.W.42 St. Lauderdale Lakes, FL 33319 William Walter Mee 8591 Pioneer Road West Palm

More information

SE-DUZ Direct-Drive All-Electric Series

SE-DUZ Direct-Drive All-Electric Series SE-DUZ Direct-Drive All-Electric Series SE-DUZ Series Direct-Drive All-Electrics Low-inertia, high-performance direct-drive motors for plasticizing, injection, clamping and ejection New PC-based control

More information

26 Series Stainless Steel 2-way Ball Valves

26 Series Stainless Steel 2-way Ball Valves 1-800-899-0553 26 Series Stainless Steel 2-way Ball Valves Users Manual Installation, Operation, & Maintenance 1. General Precaution 1.1. Material Section Material deterioration is determined by the contained

More information

Maintenance and lubrication products

Maintenance and lubrication products Maintenance and lubrication products Mechanical tools... 1070 Hook and impact spanners... 1070 Lock nut spanners and axial lock nut sockets... 1070 Bearing fitting tools... 1070 Jaw pullers... 1071 Strong

More information

Thermal Unit Operation (ChEg3113)

Thermal Unit Operation (ChEg3113) Thermal Unit Operation (ChEg3113) Lecture 9- Shell and Tube Heat Exchanger Design Instructor: Mr. Tedla Yeshitila (M.Sc.) Today Review Shell and tube heat exchanger Steps in Shell and tube heat exchanger

More information

Efficient side gating

Efficient side gating Customer information from EWIKON Heißkanalsysteme GmbH October 2013 Efficient side gating Production of technical parts for a vacuum cleaner Pages 2-4 NEW product! HPS III-MV valve gate nozzle for process-reliable

More information

Autodesk Moldflow Insight AMI Modeling the cooling system

Autodesk Moldflow Insight AMI Modeling the cooling system Autodesk Moldflow Insight 2012 AMI Modeling the cooling system Revision 1, 22 March 2012. This document contains Autodesk and third-party software license agreements/notices and/or additional terms and

More information

(12) Patent Application Publication (10) Pub. No.: US 2004/ A1

(12) Patent Application Publication (10) Pub. No.: US 2004/ A1 US 2004.00431 O2A1 (19) United States (12) Patent Application Publication (10) Pub. No.: US 2004/0043102 A1 H0 et al. (43) Pub. Date: Mar. 4, 2004 (54) ALIGNMENT COLLAR FOR A NOZZLE (52) U.S. Cl.... 425/567

More information

Article on Sheath materials, Thermowells, Fittings, and Terminations

Article on Sheath materials, Thermowells, Fittings, and Terminations Article on Sheath materials, Thermowells, Fittings, and Terminations 1. INTRODUCTION Temperature sensor element for laboratory and industrial use should normally be protected by some form of sheath or

More information

Polyshot Heated Sprue Bushings

Polyshot Heated Sprue Bushings Polyshot Heated Sprue Bushings Machine Nozzle Sealing Radius Hard Tool Steel Body All Wiring Runs Through Top Clamp Plate Stainless Steel Replaceable Collar Flow Path Independent Thermocouple Profiled/Tapered

More information

Motor Driver PCB Layout Guidelines. Application Note

Motor Driver PCB Layout Guidelines. Application Note AN124 Motor Driver PCB Layout Guidelines Motor Driver PCB Layout Guidelines Application Note Prepared by Pete Millett August 2017 ABSTRACT Motor driver ICs are able to deliver large amounts of current

More information

Haitian Partner: HAITIAN INTERNATIONAL HOLDINGS LIMITED Unit 1105 Level 11 Metroplaza Tower Hing Fong RD Kwai Fong N.T

Haitian Partner: HAITIAN INTERNATIONAL HOLDINGS LIMITED Unit 1105 Level 11 Metroplaza Tower Hing Fong RD Kwai Fong N.T HAITIAN INTERNATIONAL HOLDINGS LIMITED Unit 1105 Level 11 Metroplaza Tower 2 223 Hing Fong RD Kwai Fong N.T haitian@mail.haitian.com www.haitian.com Haitian Partner: HT 20100805-EV NINGBO HAITIAN HUAYUAN

More information

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM)

INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) INSTALLATION, OPERATION AND MAINTENANCE MANUAL (IOM) IOM-1088 03-16 Model 1088 Vacu-Gard Blanketing Valve ISO Registered Company SECTION I I. DESCRIPTION AND SCOPE The Model 1088 Vacu-Gard is a tank blanketing

More information

polymer Blending As-supplied or Concentrated Polymer Polymer is a long chain Effects of Insufficient Mixing Energy When insufficient

polymer Blending As-supplied or Concentrated Polymer Polymer is a long chain Effects of Insufficient Mixing Energy When insufficient our History Right from the start... In 1985 Fluid Dynamics developed the high energy, non-mechanical dynablend liquid polymer activation and blending technology. Immediately it proved to be a revolutionary

More information

Customer information from EWIKON Heißkanalsysteme GmbH. Doubled output. New stack mould concept for the production of syringe plungers

Customer information from EWIKON Heißkanalsysteme GmbH. Doubled output. New stack mould concept for the production of syringe plungers Customer information from EWIKON Heißkanalsysteme GmbH Doubled output New stack mould concept for the production of syringe plungers Pages 2-4 Enhanced operational safety More performance for small machines

More information

PUMPS STEAM TURBINES BUILDING & FIRE WASTEWATER SERVICE PUMP CLINIC 15 MECHANICAL SEAL DESIGN, OPERATION AND MAINTENANCE PROBLEMS

PUMPS STEAM TURBINES BUILDING & FIRE WASTEWATER SERVICE PUMP CLINIC 15 MECHANICAL SEAL DESIGN, OPERATION AND MAINTENANCE PROBLEMS PUMP CLINIC 15 MECHANICAL SEAL DESIGN, OPERATION AND MAINTENANCE PROBLEMS In my seminars I teach that mechanical seals fail prematurely because: The lapped faces open A seal component becomes damaged In

More information

What is Wear? Abrasive wear

What is Wear? Abrasive wear What is Wear? Written by: Steffen D. Nyman, Education Coordinator, C.C.JENSEN A/S It is generally recognized that contamination of lubricating and hydraulic oils are the primary cause of wear and component

More information

ALLROUNDER 275 V. Vertical free-space system Clamping force: 28 tons Injection unit: 1.4 oz, 2.3 oz

ALLROUNDER 275 V. Vertical free-space system Clamping force: 28 tons Injection unit: 1.4 oz, 2.3 oz ALLROUNDER 275 V Vertical free-space system Clamping force: 28 tons Injection unit: 1.4 oz, 2.3 oz MACHINE DIMENSIONS 275 V 35.43 2.18 70.1 113.39 1) 119.1 2) 111.81 1) 115.95 2).57 75.1 31.5 35.43 min.35.43

More information

PROMAG SR SERIES SEAL-LESS CENTRIFUGAL PUMPS

PROMAG SR SERIES SEAL-LESS CENTRIFUGAL PUMPS PROMAG SR SERIES SEAL-LESS CENTRIFUGAL PUMPS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS TO OBTAIN THE BEST PERFORMANCE FROM YOUR PROMAG SR PUMP, PLEASE READ THE MANUAL CAREFULLY. Failure to

More information

MCF BALL VALVES OVERVIEW

MCF BALL VALVES OVERVIEW MCF BALL VALVES OVERVIEW ISSUED JULY 2014 MCF BALL VALVES OVERVIEW THE CENTER OF MCF MODULAR THREE-PIECE VALVE CONSTRUCTION, ISO 5211 TYPE BODY CONFIGURATION, ACCOMMODATES A WIDE CHOICE OF SEATS, SEALS,

More information

Comparison between Fluid Viscous Dampers and Friction Damper Devices. Fluid Viscous Dampers (FVD) Friction Damper Device (FDD) Working principle:

Comparison between Fluid Viscous Dampers and Friction Damper Devices. Fluid Viscous Dampers (FVD) Friction Damper Device (FDD) Working principle: Fluid Viscous Dampers (FVD) Working principle: FVD is a central piston strokes through a fluid-filled chamber. As the piston moves it pushes fluid through orifices around and through the piston head. Fluid

More information

How to Achieve a Successful Molded Gear Transmission

How to Achieve a Successful Molded Gear Transmission How to Achieve a Successful Molded Gear Transmission Rod Kleiss Figure 1 A molding insert tool alongside the molded gear and the gear cavitiy. Molded plastic gears have very little in common with machined

More information

Testing and Measuring Extruders The high performance machine for plasticizing of polymers and elastomers

Testing and Measuring Extruders The high performance machine for plasticizing of polymers and elastomers Laboratory machines for the processing of polymers Testing and Measuring Extruders The high performance machine for plasticizing of polymers and elastomers From polymer to information Testing Extruder

More information

Plastics & Packaging ONE STOP SHOPPING. Canada USA

Plastics & Packaging ONE STOP SHOPPING. Canada USA T H E C O N V E Y I N G P R O D U C T S P E O P L E Plastics & Packaging C O N V E Y I N G P R O D U C T S G U I D E Canada 1-800-263-1942 USA 1-800-263-7782 sales@lorenz.ca www.lorenzproducts.com ISO

More information

TRANSLATION (OR LINEAR)

TRANSLATION (OR LINEAR) 5) Load Bearing Mechanisms Load bearing mechanisms are the structural backbone of any linear / rotary motion system, and are a critical consideration. This section will introduce most of the more common

More information

Silencers. Transmission and Insertion Loss

Silencers. Transmission and Insertion Loss Silencers Practical silencers are complex devices, which operate reducing pressure oscillations before they reach the atmosphere, producing the minimum possible loss of engine performance. However they

More information

DK/CP DN PVC-U / PVC-C / PP-H / PVDF. Pneumatically actuated 2-way diaphragm valve

DK/CP DN PVC-U / PVC-C / PP-H / PVDF. Pneumatically actuated 2-way diaphragm valve PVC-U / PVC-C / PP-H / PVDF Pneumatically actuated 2-way diaphragm valve DK/CP DN 15 32 The new DK/CP diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids.

More information

The multi-function machine

The multi-function machine The multi-function machine Technical Description Multi Clamping unit asic hydraulic 500 kn 800 kn 1100 kn 18,5 kw 22 kw 30 kw Injection unit/ Distance Screw between tie bars V V V 370 x 370 120 200 22/25/30

More information

Nexus Pre-Wired Hot Runner System

Nexus Pre-Wired Hot Runner System Nexus Pre-Wired Hot Runner System www.mastip.com Overview Assembly Overview L Key Features Fast and simple installation out of the box Incorporates advanced heating technology for superior thermal performance

More information

Oil Streak Air-Oil Generating Unit

Oil Streak Air-Oil Generating Unit Oil Streak Air-Oil Generating Unit GENERAL The Air-Oil Generating system delivers high efficiency lubrication for high-speed spindles and other applications requiring accurate oil deliveries, in combination

More information

Blast off. technology INTERNATIONAL

Blast off. technology INTERNATIONAL technology INTERNATIONAL Blast off CO 2 blasting has had a big impact on tire mold maintenance. Strengths include in-press cleaning and simultaneous microvent clearance. Molding the final tire shape and

More information

FF Series Drawer Magnet

FF Series Drawer Magnet Series Drawer Magnet Slide ate Magnetic Latch i-strength Nylon Knobs Optional Right- or Left-and Mounted Purge opper (Right-and shown) Optional Dump Tube (may be located on any side) MODEL 4600-PLS NEO

More information

Combustion Equipment. Combustion equipment for. Solid fuels Liquid fuels Gaseous fuels

Combustion Equipment. Combustion equipment for. Solid fuels Liquid fuels Gaseous fuels Combustion Equipment Combustion equipment for Solid fuels Liquid fuels Gaseous fuels Combustion equipment Each fuel type has relative advantages and disadvantages. The same is true with regard to firing

More information

MMX Series High Accuracy, Energy Saving Large Hydraulic Injection Molding Machines

MMX Series High Accuracy, Energy Saving Large Hydraulic Injection Molding Machines Mitsubishi Heavy Industries Technical Review Vol. 49 No. 4 (December 2012) 23 MMX Series High Accuracy, Energy Saving Large Hydraulic Injection Molding Machines Mitsubishi Heavy Industries Plastic Technology

More information

EJECTORS GENERAL OPERATION & MAINTENANCE MANUAL

EJECTORS GENERAL OPERATION & MAINTENANCE MANUAL EJECTORS GENERAL OPERATION & MAINTENANCE MANUAL The information contained in this manual was current at the time of printing. The most current versions of all Hydro Instruments manuals can be found on

More information

Machine shut-off nozzle for Elastomer; Type-E Integrated actuator and tempering system

Machine shut-off nozzle for Elastomer; Type-E Integrated actuator and tempering system Machine shut-off nozzle for Elastomer; Type-E Integrated actuator and tempering system Application: Elastomeric plastics Shut-off technique: Integrated two way pneumatic actuator Characteristics: Integrated

More information

Peel Grinding. High speed peel grinder from Weldon Solutions

Peel Grinding. High speed peel grinder from Weldon Solutions Peel Grinding Although more widely accepted in Europe, US manufacturers are now starting to show an interest in peel grinding in two primary areas. 1) As an alternative to conventional formed wheel plunge

More information

High Speed, Low Weight Momentum/reaction Wheels. Larry Wilhide, Valley Forge Composite Tech, Inc. P.O. Box 344 Carlisle, PA (717)

High Speed, Low Weight Momentum/reaction Wheels. Larry Wilhide, Valley Forge Composite Tech, Inc. P.O. Box 344 Carlisle, PA (717) SSC99-XI-1 High Speed, Low Weight Momentum/reaction Wheels, Valley Forge Composite Tech, Inc. P.O. Box 344 Carlisle, PA 17013 (717) 776-3249 Louis Brothers, Valley Forge Composite Tech, Inc. P.O. Box 344

More information