PARTS LIST INDEX. (Continued On Next Page) P1 10/08

Transcription

1 PARTS LIST INDEX ROW UNIT 15" Seed Opener Disc Blade/Bearing Assembly And Scrapers...P13 Air Compressor Package Option, Dual Solenoid Assembly, Tubing And Fiittings... P10 Coulter Mounted Residue Wheels...P36 Covering Discs/Single Press Wheel...P16 Drag Closing Attachment...P19 Frame Mounted Coulter W/Residue Wheels...P38 Gauge Wheels...P14 Granular Chemical Banding Options...P27 Granular Chemical Hopper And Hopper Panel Extension...P24 Granular Chemical Meter And Meter Drive...P26 Hopper Support And Meter Drive...P20 Pneumatic Down Pressure Package Option And Pull Row Unit, Air Clutch Package... P6 Parallel Arms, Mounting Support Plate And Quick Adjustable Down Force Springs Option...P12 Pneumatic Down Pressure Control Console, Sending Unit And Harnesses...P8 Row Unit Mounted Bed Leveler...P30 Row Unit Mounted Disc Furrower...P32 Row Unit Mounted No Till Coulter...P29 Row Unit Mounted Residue Wheel...P34 Seed Hopper And Lid...P21 Seed Meter...P22 Shank Assembly, Seed Tube And Depth Adjustment...P4 Spring Tooth Incorporator...P28 V Closing Wheels...P18 EDGEVAC SYSTEM Digital Vacuum Gauge, Analog Vacuum Gauge And Vacuum Fan Assembly...P44 Manifolds And Distribution Hoses...P50 Optional Flow Control Needle Valve Kit...P48 PTO Pump Drive And Oil Cooler Option...P52 Vacuum Fan Hydraulic Components...P46 Vacuum Fan Hydraulic Motor Assembly...P48 Vacuum Fan Motor Valve Block Assembly (Located Below Vacuum Fan Motor Assembly)...P49 (Continued On Next Page) P1 10/08

2 PARTS LIST INDEX BASE MACHINE 2-Point Hitch Option...P56 Axle Assembly...P72 Bolt-On Wheel Module/Transport Latch Catch...P82 Center Frame...P64 Center Pivot...P70 Contact Wheel And Drive Shaft(s)...P76 Cylinders...P96 Electrical Components...P114 Ground Drive Wheel...P79 Hose Take-Up...P62 Hydraulic Drive Package Option...P66 Hydraulic Hoses And Fittings...P110 Inner Hitch...P58 Inner Module Drive...P83 Outer Hitch...P54 Point Row Clutch...P84 Row Marker Assemblies...P92 Row Marker Spindle/Hub/Blade...P91 Safety Chain...P54 Seed Rate Transmission And Row Unit Drill Shafts...P80 Transport Wheels/Rock Guards...P74 Two-Speed Point Row Clutch...P86 Two-Speed Point Row Clutch Wheel Module Extension...P88 Valve And Junction Blocks...P104 Valve Box...P116 Valves (Solenoid, Flow Control, Pressure Relief, Check, Proportional)...P108 Wing Frame...P68 ELECTRONIC SEED MONITOR KINZE Cobalt Display...P120 KINZE Vision Display...P122 KPM III Electronic Seed Monitor...P118 Planter Monitor Module (PMM)...P124 INTERPLANT SYSTEM Interplant Push Row Unit...P40 Interplant Push Row Unit, Air Clutch Package...P42 Interplant Push Row Unit Drive...P126 FERTILIZER Dry Fertilizer...P140 Fertilizer Openers, Mounts And Attachments...P128 Liquid Fertilizer...P146 Rear Trailer Hitch...P162 Decals, Paint And Miscellaneous...P164 Numerical Index...P169 P2 10/08

3 PARTS LIST INDEX This page left blank intentionally. P3 10/08

4 SHANK ASSEMBLY, SEED TUBE AND DEPTH ADJUSTMENT (D17014/RU166/A10142a/D16245) P4 10/08

5 SHANK ASSEMBLY, SEED TUBE AND DEPTH ADJUSTMENT (Per Row) 1. G Hex Washer Head Cap Screw, ⅜"-16 x 1 ¼" 2. GB Cover, Depth Adjustment 3. GB Handle, Depth Adjustment 4. GB Lever, Depth Adjustment 5. GD Cap Plug 6. GD Spring 7. GD Pin, ⅜" x 1 ⅔" 8. GD Sleeve, ⅜" I.D. x ⅝" O.D. x " Long 9. G Hex Head Cap Screw, ⅜"-24 x 2 ½", Grade 8 G Lock Nut, ⅜"-24, Grade C 10. G Chain, No. 41, 108 Pitch Including Connector Link G Chain, No. 41, 16 Pitch Including Connector Link (Used W/Row Unit Extension Brackets) GR Connector Link, No GD Sleeve, " Long 12. G Special Washer, ⅜" x 1 ½" O.D. 13. GD Idler Spring 14. GD Sleeve, 1" Long 15. G Lock Nut, ⅜" G Washer, ⅜" USS 17. GD Idler 18. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Lock Nut, ⅜" GD Stop 20. G Hex Head Cap Screw, ⅜"-16 x 3 ¾" 21. G Clevis Pin, ¼" x 2 ½" G Hair Pin Clip, No G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" GD Shield Wheel Arm, See Gauge Wheels, Pages P14 And P GA Shank W/Gauge Wheel Pivot Spindle And Set Screw GD Spindle G Hex Head Cap Screw, ½"-13 x ¾" 26. G Washer, ⅞" O.D. x 13 32" I.D. x.134" (If Applicable) 27. GD Dust Cap 28. See Planter Monitor Module (PMM), Pages P124 And P GB Collar, Depth Adjustment 30. GB Pivot Link, Depth Adjustment 31. GD Sun Shade (Rubber) 32. G Hex Head Cap Screw, ⅜"-16 x 1 ¾" G Washer, ⅜" SAE G Lock Nut, ⅜" GD Hose Guide 34. G Hex Slotted Head Cap Screw, #10-32 x 1" G Serrated Flange Nut, # GA Limit Switch W/Cable 36. GD Implement Switch Bracket A. GA Implement Switch Assembly, (Items 34-36) P5 10/08

6 PNEUMATIC DOWN PRESSURE PACKAGE OPTION AND PULL ROW UNIT, AIR CLUTCH PACKAGE OPTION (RU157c/RU159a/RU157d/A12405) Pull Row Unit Shown NOTE: Items that are not referenced on this page may be referenced on page P12. Push Row Unit Shown P6 10/08

7 PNEUMATIC DOWN PRESSURE PACKAGE OPTION AND PULL ROW UNIT, AIR CLUTCH PACKAGE OPTION (Per Row) 1. GA Air Spring Assembly 2. GB Saddle 3. G Hex Head Cap Screw, ⅝"-18 x 1 ¼" GD Special Washer, ⅝", Hardened GD Sleeve, ⅞" O.D. x ⅝" I.D. x 21 32" 4. GB Head Mount 5. GB Shoulder Nut, ¾" GB Bracket 7. G Hex Socket Cap Screw, ½"-13 x 1 ½" G Serrated Flange Nut, ½" G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" SAE GD Spacer, ¼" G Lock Nut, ⅜" GD Link 10. GB Plate 11. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Washer, ½" SAE (Lower Two Holes Only) G Lock Washer, ½" 12. GB Yoke Mount 13. GB Yoke 14. GB Mount 15. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GB Plate 17. GB Extension 18. G Hex Head Cap Screw, ½"-13 x 1 ¾" G Washer, ½" SAE G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 1 ¼" G Lock Washer, ½" 20. GD Spacer, 1 ¼" O.D. x 1" 21. G Hex Head Cap Screw, ¼"-20 x ⅝" 22. GR Sprocket, 19 Tooth 23. G Retaining Ring 24. G Slotted Flat Head Machine Screw, No x ½", Stainless Steel 25. GR Air Housing Cover 26. GR Sprocket Hub 27. GR Ratchet Gear 28. GR Clutch Spring 29. GR Hex Bushing 30. GR Air Clutch Housing 31. G Hex Head Cap Screw, ¼"-20 x ¾" G Hex Nut, ¼" GR Air Cylinder 33. GR Push Connect, ⅛" NPT Male x ¼" 34. G Pan Head Machine Screw, ¼"-20 x ¾" x ¾" 35. GR Filter 36. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 37. GD Lock Clamp 38. GA Bearing/Sprocket, ⅞" Hex Bore A. GA Air Clutch Assembly, (Items 20-35) P7 10/08

8 PNEUMATIC DOWN PRESSURE CONTROL CONSOLE, SENDING UNIT AND HARNESSES (PNE30b/MTR27a/ELC27b/MTR45/MTR27t/PNE30c) P8 10/08

9 PNEUMATIC DOWN PRESSURE CONTROL CONSOLE, SENDING UNIT AND HARNESSES 1. GA Power Lead Adapter 2. GA Control Box Assembly 3. GA Sending Unit 4. GA Wiring Harness W/Fuse Holder And Fuse, 206" GD Fuse Holder GD Fuse, 2 Amp Delay Action 5. G1K268 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (1) Lock Ring, (3) Female Terminal Pins 6. G1K267 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (3) Male Terminal Pins 7. GA Strain Relief 8. GR Hex Face Nut, 15 32"-32 GR Internal Tooth Lock Washer, 15 32" 9. GA Switch, 3 Position Toggle, Momentary On-Off-Momentary On 10. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 11. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 12. GA Pin Female Connector Kit, Includes: (1) 4-Pin Female Housing, (4) Pin Contacts, (4) Seals 13. GA Pin Male Connector Kit, Includes: (1) 4-Pin Male Housing, (4) Socket Contacts, (4) Seals 14. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 15. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 16. GA Strain Relief 17. GA Wiring Harness W/Fuse Holder And Fuse, 60' GD Fuse Holder GD Fuse, 20 Amp 18. GA Wiring Harness, 60' 19. See Air Compressor Package Option, Dual Solenoid Assembly, Tubing And Fittings, Pages P10 And P GD Nylon Tubing, ¼" O.D. x 1 ½' 21. GD Reducer, ⅜" To ¼" 22. GD Tee, ⅜" Tube Union 23. GA Hall Effect Adapter 24. See Planter Monitor Module (PMM), Pages P124 And P125 P9 10/08

10 AIR COMPRESSOR PACKAGE OPTION, DUAL SOLENOID ASSEMBLY, TUBING AND FITTINGS (PNE06a/PNE02/PNE05/A13169/PNE09/PNE08) P10 10/08

11 AIR COMPRESSOR PACKAGE OPTION, DUAL SOLENOID ASSEMBLY, TUBING AND FITTINGS 1. GD Cover 2. G Phillips Pan Head Machine Screw, No x ¾", Stainless Steel G Serrated Flange Nut, No GA Air Compressor 4. GA Filter Assembly GR Filter 5. GA Mount 6. G Hex Head Cap Screw, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" GA Valve Stem, ¼" NPT 8. GD Nipple, ¼" NPT 9. GD Plug, ¼" NPT 10. GD Tee, ¼" NPT 11. GA Tank, 3 Gallon 12. GA Drain, ¼" NPT 13. GR Pressure Switch 14. GA Tube Cutter W/Blade GR Blade 15. G Slotted Pan Head Machine Screw, M4-0.7 x GA Shutoff Valve, ¼" NPT 17. GD Plug, ¼" NPT 18. GA Breather, ¼" NPT 19. GD Connector, ¼" Male 20. GA Block 21. GD Connector, ¼" Male 22. GA Solenoid 23. GD Female Cross, ¼" NPT 24. GA Pressure Gauge, ¼" NPT 25. GD Swivel Elbow, ¼" NPT x ⅜" 26. GD U-Bolt, 3" x 3" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Compressor Mount 28. G Hex Head Cap Screw, ¼"-20 x 1 ¾" G Lock Washer, ¼" G Washer, ¼" USS 29. GD Tee, ⅜" Tube Union, Pull Row Unit (Pneumatic Down Pressure) GD Tee, ⅜" x ⅛" NPT Extended, Push Row Unit (Pneumatic Down Pressure) GD Tee, ¼" Press On, Pull/Push Row Units (Air Clutch) 30. GD Nylon Tubing, ⅜" O.D. x 44', 8 Row Pull Row Units (Pneumatic Down Pressure) GD Nylon Tubing, ⅜" O.D. x 64', 12 Row Pull Row Units (Pneumatic Down Pressure) GD Nylon Tubing, ⅜" O.D. x 86', 16 Row Pull Row Units (Pneumatic Down Pressure) GD Nylon Tubing, ⅜" O.D. x 60', 11 Row Push Row Units (Pneumatic Down Pressure) GD Nylon Tubing, ⅜" O.D. x 82', 15 Row Push Row Units (Pneumatic Down Pressure) GD Nylon Tubing, ⅜" O.D. x 5', Even-Row Push Row Unit (Pneumatic Down Pressure) GD Nylon Tubing, ¼" O.D. x 52', 12 Row Pull/Push Row Units (Air Clutch) GD Nylon Tubing, ¼" O.D. x 70', 16 Row Pull Row Units (Air Clutch) GD Nylon Tubing, ¼" O.D. x 37', 11 Row Push Row Units (Air Clutch) 31. GD Elbow, ⅜" x ⅛" NPT Extended, Pull Row Unit (Pneumatic Down Pressure) A. GA Air Compresor Assembly (Items 1-14) B. GA Dual Solenoid Assembly (Items 15-25) P11 10/08

12 PARALLEL ARMS, MOUNTING SUPPORT PLATE AND QUICK ADJUSTABLE DOWN FORCE SPRINGS OPTION RUB021/RUB022(RU78f/B0366) (Per Row) 1. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Mounting Support Plate 3. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 4. GD Upper Parallel Arm 5. G Hex Head Cap Screw, ⅝"-18 x 2" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GB Spring Anchor 7. GD Tab Lock Pin, 7 16" x 1 ½" 8. GD Spring 9. - See Hopper Support And Meter Drive, Page P20t 10. GA Lower Parallel Arm 11. GA Bearing/Sprocket, ⅞" Hex Bore 12. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GB Extension Bracket A. G6325X - U-Bolt Package For 5" x 7" Toolbar, Includes: (2) GD1113, (4) G10230, (4) G10104 P12 10/08

13 15" SEED OPENER DISC BLADE/BEARING ASSEMBLY AND SCRAPERS (RU139) (Per Row) 1. G Hex Head Cap Screw, ⅜"-16 x ⅝" G Serrated Flange Nut, ⅜" GA2012R 1 Disc Scraper, R.H. GA2012L - Disc Scraper, L.H. (Shown) 3. G Rivet, ¼" x ½" 4. GD Special Hex Head Cap Screw, ⅝"-11 x 1 ½", L.H. Threads G Hex Head Cap Screw, ⅝"-11 x 1 ½" 5. GD Dust Cap 6. G Special Machine Bushing, ⅝" x 1" O.D. 7. GD Bearing Housing 8. GA Bearing 9. GD Disc Blade, 3.5 mm x 15" 10. G Machine Bushing, ⅝" (.030" Thick)(As Required) See Shank Assembly, Pages P2 And P3 12. GB Seed Tube Guard/Inner Scraper 13. G Hex Socket Head Cap Screw, 5 16"-18 x 1", Grade G Hex Head Cap Screw, ⅜"-16 x 2 ¾" G Serrated Flange Nut, ⅜" GD Sleeve, ⅜" I.D. x ⅝" O.D. x " Long A. GA Disc Blade/Bearing Assembly, Less Dust Cap (Items 3 And 7-9) P13 10/08

14 GAUGE WHEELS (RU140) P14 10/08

15 GAUGE WHEELS (Per Row) 1. G Machine Bushing, 1" (.048" Thick) 2. G Washer, ½" USS 3. G Lock Washer, ½" 4. G Hex Head Cap Screw, ½"-13 x 1" 5. GD Cover 6. G Carriage Bolt, 5 16"-18 x 1 1 / 4 " G Serrated Flange Nut, 5 16" G Carriage Bolt, 5 16"-18 x 1 ¾" G Serrated Flange Nut, 5 16" G Hex Head Cap Screw, ⅝"-11 x 3" G Lock Washer, ⅝" 9. G Hex Head Cap Screw, 5 16"-18 x ⅝" G Lock Nut, 5 16"-18, Grade GD Half Wheel 11. GD Tire 12. GA Bearing 13. G Special Machine Bushing, ⅝" x 1" O.D. 14. GA Wheel Arm W/Grease Fitting, Bushings And Seals, L.H. (Shown) GA Wheel Arm W/Grease Fitting, Bushings And Seals, R.H. G Grease Fitting, ¼"-28 (Per Arm) GB Bushing, 1" I.D. x 1 ¼" O.D. x 1" Long (Per Arm) GD Seal (Per Arm) See Shank Assembly, Pages P2 And P3 A. GA Gauge Wheel Complete (Items 5-7 And 9-12) B. G1K296 - Gauge Wheel Arm Bushing And Seal Driver Kit, Includes: (1) Seal Driver, (1) Bushing Driver, (1) Instruction P15 10/08

16 COVERING DISCS/SINGLE PRESS WHEEL RUA054/RUB026(RU94d) P16 10/08

17 COVERING DISCS/SINGLE PRESS WHEEL (Per Row) 1. G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS 2. GB Wheel Arm Stop 3. G Carriage Bolt, ½"-13 x 2 ¼" G Carriage Bolt, ½"-13 x 2 ½" (Used W/Straight Drop In-Furrow Granular Chemical Bracket) G Hex Nut, ½" GA Spring 5. GB Eccentric Bushing 6. G Hex Nut, ½" G Adjusting Bolt, ½"-13 x 5" 8. GA Mounting Arm 9. G Cotter Pin, ¼" x 1 ½" 10. G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Bracket 12. GA Mount 13. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" G Lock Nut, ⅝" GD Bushing, 41 64" I.D. x ⅞" O.D. x ¼" Long 16. GD Disc Blade, 8" 17. G Hex Head Cap Screw, 5 16"-18 x ⅝" G Lock Nut, 5 16"-18, Grade G Hex Head Cap Screw, ⅝"-11 x 9" 19. GD Sleeve, ⅝" I.D. x ⅞" O.D. x 2 ⅞" Long 20. GD Half Wheel 21. GA Bearing 22. GD Tire 23. GA Bearing 24. GD Bearing Housing 25. G Rivet, ¼" x ½" 26. G Hex Head Cap Screw, ⅝"-11 x 2 ¼" 27. GD Dust Cap A. GA Single Press Wheel Complete W/Bearing (Items 17 And 20-22) B. GA Covering Disc Blade Complete W/Bearing (Items 16 And 23-25) P17 10/08

18 V CLOSING WHEELS (RU83i/RU83n) (Per Row) 1. G Carriage Bolt, ½"-13 x 2 ¼" G Carriage Bolt, ½"-13 x 2 ½" (Used W/Straight Drop In-Furrow Granular Chemical Bracket) G Lock Nut, ½" GB Wheel Arm Stop 3. G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS 4. GB Stepped Bushing 5. GB Eccentric Bushing 6. GD Spring 7. G Hex Head Cap Screw, ¼"-20 x 1" 8. G Hex Head Cap Screw, ⅝"-11 x 3 ½" G Lock Nut, ⅝" G1K345 - Closing Wheel Shield Kit W/Hardware And Instruction G Carriage Bolt, ⅜"-16 x ¾" G Carriage Bolt, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Nylon Half Wheel 11. GA Bearing 12. GD Rubber Tire, 1" x 12" 13. GD Bushing, 41 64" I.D. x ⅞" O.D. x ¼" Long 14. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade GA Cast Iron Closing Wheel W/Bearing GA Bearing 16. GA Arm 17. GB Lever 18. GD Special Washer, ⅝", Hardened 19. G Lock Washer, ⅝" A. GA Rubber Closing Wheel Complete W/Bearing (Items 7 And 10-12) P18 10/08

19 DRAG CLOSING ATTACHMENT RUB050(RU90c) (Per Row) 1. G Carriage Bolt, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Front Bracket 3. GD Blade 4. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GD Rear Bracket A. G7566X - Drag Closing Attachment Complete (Items 1-5) P19 10/08

20 HOPPER SUPPORT AND METER DRIVE (METR72) (Per Row) 1. GB Hopper Mount 2. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 3. G Hex Head Cap Screw, ⅝"-18 x 2 ¼" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Hex Head Cap Screw, ⅝"-18 x 1 ¾" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Spring Pin, ¼" x 1 ½" 6. G External Retaining Ring, ⅝" 7. GD Knob 8. G Carriage Bolt, 5 16"-18 x 1 ¼" G Serrated Flange Nut, 5 16" GB Clutch Adapter Plate 10. G Hex Head Cap Screw, ⅜"-16 x 3 ½" G Washer, ⅜" USS G Lock Nut, ⅜" G Carriage Bolt, ¼"-20 x ⅝", Grade 2 G Serrated Flange Nut, ¼" GA Hopper Hold Down Latch 13. GA Hopper Support 14. GA Double Sprocket And Bearing, Drive Clutch, 11/28 Tooth 15. GD Spring 16. GD Shaft 17. GB Coupler 18. G Spring Pin, 3 16" x 1 ¼" 19. GD Bolt-On Sprocket, 28 Tooth 20. G Hex Socket Button Head Cap Screw, 5 16"-18 x ½", Stainless Steel G Serrated Flange Nut, 5 16" GA Double Sprocket And Bearing, Drive Clutch, 11/19 Tooth A. GA Meter Drive Assembly, 11/28 Tooth (Items 5-7 And 14-18) P20 10/08

21 SEED HOPPER AND LID (METR12) 1. GD Lid 2. GA Seed Hopper P21 10/08

22 SEED METER (METR69/METR65/A12133) Used With 60 Cell Milo/Grain Sorghum Disc, 60 Cell Soybean Disc, 120 Cell High-Rate Soybean Disc And 39 Cell And 24 Cell Popcorn Discs Used With 60 Cell Milo/Grain Sorghum Disc Used With 20 Cell Hill-Drop Acid-Delinted Cotton Discs; 54 Cell Acid-Delinted Cotton/ Small Dry Edible Bean Disc; And Small Cotton/Sunflower Disc P22 10/08

23 SEED METER 1. GA Vacuum Cover W/Elbow And Cap GD " Hose Barb Elbow GD Cap 2. GA Cleanout Brush (Used With 60 Cell Milo/Grain Sorghum Disc) 3. GD Seed Disc, Corn/Popcorn, 39 Cell, Light Blue Color-Coded GD Seed Disc, Low-Rate Corn/Popcorn, 24 Cell, Light Green Color-Coded GD Seed Disc, Soybean, 60 Cell, Black Color-Coded GD Seed Disc, High-Rate Soybean, 120 Cell, Dark Blue Color-Coded GD Seed Disc, Milo/Grain Sorghum, 60 Cell, Yellow Color-Coded GD Seed Disc, Hill-Drop Cotton, Acid-Delinted, 3 Seeds Per Cell, 20 Cell, Brown Color-Coded GD Seed Disc, Small Hill-Drop Cotton, Acid-Delinted, 20 Cell (3 Seeds Per Cell), Grey Color-Coded GD Seed Disc, Cotton, Acid-Delinted/Small Dry Edible Bean, 54 Cell, Dark Green Color-Coded GD Seed Disc, Small Cotton/Sunflower, 54 Cell, White Color-Coded GD Seed Disc, Large Dry Edible Bean, 54 Cell, Tan Color-Coded 4. GD Wall Brush/Vent 5. GD Foam Spacer 6. GB Mount 7. GA Bearing 8. GD Discharge Cover 9. G Spring Pin, ¼" x 1 ½" 10. G Spring Pin, ¼" x 1 ¼" 11. G Hex Socket Head Cap Screw, ¼"-20 x ¾" 12. GA Crowder Brush 13. G Hex Socket Head Cap Screw, ¼"-20 x ½" 14. GD Air Inlet Screen 15. GD Push Nut, ⅛" I.D. 16. GA Singulator Brush 17. GD Spring 18. GB Cap 19. GD Brush Adjustment Lever 20. G Hex Socket Head Cap Screw, No x ⅜", Stainless Steel 21. G Hex Socket Head Shoulder Screw, ¼"-20 x ⅜", Stainless Steel 22. GB Housing 23. G Locking Thumbscrew, 5 16"-18 x ¾" 24. GD Seed Baffle (Used With 60 Cell Milo/Grain Sorghum Disc, 60 Cell Soybean Disc, 120 Cell High-Rate Soybean Disc And 39 Cell And 24 Cell Popcorn Discs) 25. G Rib Neck Bolt, ¼"-20 x ¾" G Hex Flange Nut, ¼"-20, No Serrations 26. GD Shank Cover, EdgeVac Meter 27. GA Cleanout Brush W/Ball-Type Ejector (Used With 20 Cell Hill-Drop Acid-Delinted Cotton Discs And 54 Cell Acid-Delinted Cotton/Small Dry Edible Bean And Small Cotton/Sunflower Discs) P23 10/08

24 GRANULAR CHEMICAL HOPPER AND HOPPER PANEL EXTENSION (METR14d) P24 10/08

25 GRANULAR CHEMICAL HOPPER AND HOPPER PANEL EXTENSION (Per Row) 1. G Washer, ⅜" USS 2. GD Sleeve, 9 16" Long 3. GD Spring 4. G Special Washer, ⅜" x 1 ½" O.D. 5. GD Sleeve, " Long 6. GD Idler 7. G Lock Nut, ⅜" G Hair Pin Clip, No GD1059L 1 Support, L.H. (Shown) GD1059R 1 Support, R.H. 10. G Hex Head Cap Screw, ⅜"-16 x ¾" G Lock Washer, ⅜" 11. G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" G Hex Head Cap Screw, ⅜"-16 x 2 ¾" 13. G External Retaining Ring, ⅝" 14. GD Plate 15. A Hopper Panel Extension (Non-Stock Item) (Sub Wholegoods Order Code ) 16. GD Block 17. G Hex Head Cap Screw, ¼"-20 x ¾" G Serrated Flange Nut, ¼" GD Hinge 19. GA Hopper 20. GA Lid 21. GD Knob 22. G Spring Pin, ¼" x 1 ½" P25 10/08

26 GRANULAR CHEMICAL METER AND METER DRIVE RUA051/RUB028(RU91a) (Per Row) 1. G External Retaining Ring, ⅝" 2. GD Knob 3. G Spring Pin, ¼" x 1 ½" 4. - See Granular Chemical Hopper And Hopper Panel Extension, Pages P24 And P25 5. GA Sprocket And Bearing, Drive Clutch, 24 Tooth 6. GD Spring 7. GD Shaft 8. GB Coupler 9. G Spring Pin, 3 16" x 1 ¼" 10. GD Shaft 11. G Hex Socket Head Cap Screw, No x ⅞" G Lock Washer, No GD Feed Roller, Hex Bore 13. GB Bearing 14. GD Hex Bushing 15. G Chain, No. 41, 108 Pitch Including Connector Link GR Connector Link, No G Wave Washer, ½" 17. G Washer, ¼" USS 18. G Slotted Hex Self-Tapping Screw, ¼"-20 x ¾" 19. G Slotted Hex Self-Tapping Screw, No. 10 x ⅜" 20. GD Support Strap 21. GD Metering Gate 22. GB Granular Housing A. GA Granular Chemical Meter Complete (Items 1, 9, 10, And 16-22) P26 10/08

27 GRANULAR CHEMICAL BANDING OPTIONS RUA061/RUA073(RU101mm/RU83m) 1. GD Funnel 2. G Wire Hose Clamp, ¾" 3. GD Hose, 7 16" x 28" 4. G Slotted Pan Head Self-Tapping Screw, No. 10 x ½" 5. GA Slope-Compensating Bander W/Hardware (4 ½" Band Width) G Uni-Clamp G Pan Head Screw, No x 1 ¼" G Hex Nut, No GD U-Bolt, 1 ½" x " x ¼"-20 G Washer, ¼" USS G Lock Nut, ¼"-20, Grade B 7. GD Spacer 8. GD1115L - Hanger Bracket, L.H. 9. G Cotter Pin, ⅛" x ½" 10. GD1115R - Hanger Bracket, R.H. 11. G Carriage Bolt, ¼"-20 x ¾", Grade 2 G Lock Washer, ¼" G Hex Nut, ¼" GD Hanger 13. GA Diffuser, 14" Band 14. G Carriage Bolt, ⅜"-16 x 2" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Clamp 16. G Carriage Bolt, ½"-13 x 2 ½" (Replaces Existing ½" x 2 ¼" Hardware) 17. GA Bracket (Straight Drop In-Furrow) 18. G1K385 - Bander Shield Kit W/Hardware And Instruction G Hex Head Cap Screw, ⅜"-16 x 1 ½" GD Special Washer, ⅜", Hardened P27 10/08

28 SPRING TOOTH INCORPORATOR RUA055(RU95) (Per Row) 1. G Serrated Flange Nut, ¼" GD Eyebolt, ¼" G Twin Loop Chain, 9 Links 4. GD Front Bracket 5. G Carriage Bolt, ⅜"-16 x 1" G External Tooth Lock Washer, ⅜" G Serrated Flange Nut, ⅜" GD Spring Tooth 7. G Carriage Bolt, ⅜"-16 x ¾" G Serrated Flange Nut, ⅜" GD Rear Bracket 9. GA Cable Assembly P28 10/08

29 ROW UNIT MOUNTED NO TILL COULTER (D14398/RU102c/RU152) (Per Row) 1. G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GA Arm 3. G Hex Head Cap Screw, ⅝"-11 x 4" G Lock Nut, ⅝" G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GD Adapter 6. GA Hub W/Bearing And Retaining Ring GA Bearing, Double Row GD Retaining Ring, " 7. GD Disc Blade, Fluted, 1", 8 Flutes (Shown) GD Disc Blade, Bubbled, 1" GD Disc Blade, Fluted, ¾", 13 Flutes 8. GD Spacer P29 10/08

30 ROW UNIT MOUNTED BED LEVELER RUA059/RUA060(RU99/RU100) P30 10/08

31 ROW UNIT MOUNTED BED LEVELER (Per Row) 1. G Detent Pin, ½" x 2 ½" Grip 2. G Square Head Set Screw, ⅝"-11 x 2 ¼" 3. G Hex Jam Nut, ⅝"-11, Grade 2 4. GA Mounting Bracket 5. GD Bushing, 1" O.D. x 9 16" I.D. x 7 16" Long 6. G Hex Head Cap Screw, ½"-13 x 1 ¾" GD Special Washer, ½", Hardened G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Nut, ½" GD Link 9. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Nut, ½" GA Anchor 11. G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Nut, ½" GA Leveler 13. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Nut, 5 16"-18, Grade GD Blade P31 10/08

32 ROW UNIT MOUNTED DISC FURROWER RUA059/RUA058(RU99/RU98g) P32 10/08

33 ROW UNIT MOUNTED DISC FURROWER (Per Row) 1. G Detent Pin, ½" x 2 ½" Grip 2. G Square Head Set Screw, ⅝"-11 x 2 ¼" 3. G Hex Jam Nut, ⅝"-11, Grade 2 4. GA Mounting Bracket 5. GD Bushing, 1" O.D. x 9 16" I.D. x 7 16" Long 6. G Hex Head Cap Screw, ½"-13 x 1 ¾" GD Special Washer, ½", Hardened G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Nut, ½" GD Link 9. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Nut, ½" GA Anchor 11. G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Nut, ½" GA Support Arm 13. G Truss Head Slotted Machine Screw, 5 16"-18 x ⅞" G Hex Nut, 5 16" GD Dust Cap 15. G Hex Head Cap Screw, ⅝"-11 x 4 ½" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Hub W/Bearings GA Bearing 17. GD Disc Blade, Solid, 12" (Shown) GD Disc Blade, Notched, 12" 18. GD Spacer, 11 16" I.D. x ¾" Long GD Spacer, 11 16" I.D. x ½" Long P33 10/08

34 ROW UNIT MOUNTED RESIDUE WHEEL (RU103dd) P34 10/08

35 ROW UNIT MOUNTED RESIDUE WHEEL (Per Row) 1. GD Dust Cap 2. GB Wheel, 12 Tine, ⅜" x 12" 3. G Hex Head Cap Screw, ⅝"-11 x 2 ¼" 4. GD Backing Plate 5. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade 8 6. GD Spacer, ½" x " Long 7. GA Wheel Mount 8. G Hex Head Cap Screw, ½"-13 x 3 ½" G Lock Washer, ½" G Hex Nut, ½" GD Spring 10. G Hex Head Cap Screw, ½"-13 x 4 ½" G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 5" (Lockup Bolt) G Lock Nut, ½" GD Spacer, ½" x 3" Long 13. GA Lower Link 14. GA Mount 15. G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GA Upper Link 17. G Hex Head Cap Screw, ½"-13 x 3", Full Thread G Hex Jam Nut, ½"-13, Grade GA Hub W/Bearings GA Bearing A. GA Wheel Assembly, 12 Tine, R.H. (Items 2, 4, 5, And 18) P35 10/08

36 COULTER MOUNTED RESIDUE WHEELS (RU153) P36 10/08

37 COULTER MOUNTED RESIDUE WHEELS (Per Row) 1. GD Dust Cap 2. G Hex Head Cap Screw, ⅝"-11 x 3" G Hex Jam Nut, ⅝"-11, Grade 2 3. GA Locking Pin 4. GA Hub W/Bearings GA Bearing 5. GA Cam 6. GD Spring 7. G Washer, ½" SAE 8. G Lock Nut W/Nylon Insert, ½" G Hex Head Cap Screw, ¾"-10 x 10 ½" GB Bushing, 1 ⅛" O.D. x 25 32" I.D. x ¾" Long G Washer, ¾" SAE G Lock Nut, ¾" GB Mount 11. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Lock Washer, ⅜" 12. G Machine Bushing, ⅝" (.030" Thick) 13. GA Weed Guard W/Spring Pin G Spring Pin, ¼" x 1" 14. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade GD Backing Plate 16. GB Wheel, 12 Tine, ⅜" x 12" A. GA Wheel Assembly, 12 Tine, R.H. (Items 3, 4, 14, And 15) (Shown) GA Wheel Assembly, 12 Tine, L.H. (Items 3, 4, 14, And 15) B. G1K467 - Residue Wheel Mount Kit (Items 17-20) P37 10/08

38 FRAME MOUNTED COULTER W/RESIDUE WHEELS (RU135c/RU135g/RU153b/RU135hh) With Residue Wheels P38 10/08

39 FRAME MOUNTED COULTER W/RESIDUE WHEELS (Per Row) 1. G Hex Head Cap Screw, ¾"-10 x 12" 2. GA Plate W/Angle 3. G Hex Head Cap Screw, ½"-13 x 1 ¾" 4. GA Coulter Frame 5. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 6 ½" G Lock Nut, ¾" GD Spring Anchor Bar 8. G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GD Adapter 10. GA Hub W/Bearing And Retaining Ring GA Bearing, Double Row GD Retaining Ring, " 11. GD Disc Blade, Fluted, 1", 8 Flutes (Shown) GD Disc Blade, Bubbled, 1" GD Disc Blade, Fluted, ¾", 13 Flutes 12. GB Spring Seat 13. GD Compression Spring 14. GD Sleeve 15. G Hex Head Cap Screw, ⅝"-11 x 5" G Lock Nut, ⅝" GA Coulter Arm W/Grease Fitting G Grease Fitting, 45, ¼" G Hex Head Cap Screw, ⅝"-11 x 5 ½" G Lock Nut, ⅝" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 19. GD Dust Cap 20. G Hex Head Cap Screw, ⅝"-11 x 3" G Hex Jam Nut, ⅝"-11, Grade GB Wheel, 12 Tine, ⅜" x 12" 22. GA Hub W/Bearings GA Bearing 23. GD Backing Plate 24. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade G Machine Bushing, ⅝" (.030" Thick) 26. GA Weed Guard W/Spring Pin G Spring Pin, ¼" x 1" 27. GA Mount 28. GA Cam 29. GD Spring 30. G Lock Nut W/Nylon Insert, ½" G Hex Head Cap Screw, ⅝"-11 x 1 ¾" G Lock Nut, ⅝" GA Support 33. G Hex Head Cap Screw, ½"-13 x 1" G Hex Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 5 ½" G Washer, ⅝" SAE G Lock Nut W/Nylon Insert, ⅝" GD Sleeve, 3" A. GA Wheel Assembly, 12 Tine, R.H. (Items 21, 22, 23, And 24) (Shown) GA Wheel Assembly, 12 Tine, L.H. (Items 21, 22, 23, And 24) P39 10/08

40 INTERPLANT PUSH ROW UNIT (RU156c/R141h) NOTE: Push row units use the same seed tube, row unit depth adjustment components, quick adjustable down force springs, 15" opener disc blades, gauge wheels, closing wheels, meter drive and seed hopper as the pull row unit. See those pages for common parts. P40 10/08

41 INTERPLANT PUSH ROW UNIT (Per Row) 1. GD Sleeve, " Long 2. GD Spring 3. G Special Washer, ⅜" x 1 ½" O.D. 4. GD Sleeve, 1 ⅜" Long 5. GD Idler 6. G Washer, ⅜" USS 7. G Lock Nut, ⅜" G Chain, No. 41, 96 Pitch Including Connector Link GR Connector Link, No GA Push Row Unit Shank 10. GB Hopper Mount 11. G Hex Head Cap Screw, ⅝"-18 x 1 ¾" G Lock Nut, ⅝" G Carriage Bolt, ⅜"-16 x 1 ¼" G Hex Nut, ⅜"-16 G Lock Nut, ⅜" G Carriage Bolt, ⅜"-16 x 3 ½" 14. GD Stop 15. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Nut, ⅜" GB Seed Tube Guard/Inner Scraper 17. G Hex Socket Head Cap Screw, 5 16"-18 x 1", Grade G Hex Head Cap Screw, ⅝"-18 x 1 ¾" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 20. GA Upper Arm 21. GA Lower Arm 22. G Hex Head Cap Screw, ⅝"-18 x 2" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Bearing/Sprocket, ⅞" Hex Bore 24. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" GA Mounting Plate 26. GA T-Bolt, ⅝"-11 x 6" G Lock Washer, ⅝" G Hex Nut, ⅝" G Spring Pin, 5 16" x 1 ⅛" 28. GD Lockup 29. G Cotter Pin, ¼" x 1 ½" 30. GD Spring 31. G Clevis Pin, ½" x 1 ½" G Cotter Pin, ⅛" x ¾" 32. GD Spring Tab 33. G Washer, ½" USS 34. GA Lift Lever W/Boot GD Boot 35. GD Bracket (Lift Lever) 36. GD Wire Lock Pin, ¼" x 1 ¾" 37. GD Mount 38. G Washer, ⅜" SAE P41 10/08

42 INTERPLANT PUSH ROW UNIT, AIR CLUTCH PACKAGE (RU156d/RU141h/RU164a) NOTE: Push row units use the same seed tube, row unit depth adjustment components, quick adjustable down force springs, 15" opener disc blades, gauge wheels, closing wheels, meter drive and seed hopper as the pull row unit. See those pages for common parts. NOTE: Items that are not referenced on this page may be referenced on pages P38 and P39. P42 10/08

43 INTERPLANT PUSH ROW UNIT, AIR CLUTCH PACKAGE (Per Row) 1. GA Hanger Bearing, ⅞" Hex Bore 2. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" G Slotted Flat Head Machine Screw, No x ½", Stainless Steel 4. GR Air Housing Cover 5. GR Hex Bushing 6. GR Ratchet Gear 7. GR Clutch Spring 8. GR Sprocket Hub 9. GR Anti-Rotation 10. G Pan Head Machine Screw, ¼"-20 x ¾" x ¾" 11. GR Air Clutch Housing 12. GR Air Cylinder 13. GR Push Connect, ⅛" NPT Male x ¼" 14. GR Filter 15. G Retaining Ring 16. GR Sprocket, 19 Tooth 17. G Hex Head Cap Screw, x ½" 18. GD Spacer, 1 ¼" O.D. x 1" 19. GD Lock Clamp 20. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration A. GA Air Clutch Assembly, (Items 3-18) P43 10/08

44 DIGITAL VACUUM GAUGE, ANALOG VACUUM GAUGE AND VACUUM FAN ASSEMBLY (A11154/A11156/GR1736/A10765/A11158/A11699/A7856/A11155/A8329/METR68) Digital Vacuum Gauge Sending Unit Analog Vacuum Gauge NOTE: Torque specifications in Maintenance Section. P44 10/08

45 DIGITAL VACUUM GAUGE, ANALOG VACUUM GAUGE AND VACUUM FAN ASSEMBLY 1. GA Digital Vacuum Gauge W/4-Pin Connector 2. GA Sending Unit W/¼" Tubing And Harness W/4-Pin Male Connector GD Clear Plastic Tubing, ¼" x 45" GA Strain Relief 3. GR Hose Barb, ⅛" Male NPT To Barb 4. GD Clear Tubing, 5 16" O.D. x 3 16" I.D. x 120" 5. GA Analog Vacuum Gauge W/Hose Barb GR Hose Barb, ⅛" Male NPT To 3 16" Barb 6. GA Breather, ⅛" Male NPT 7. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Nut, ⅜" G Hex Socket Head Cap Screw, No x ⅜", Grade 8 9. GD Mount 10. GD Support 11. GA Harness, 550", 8 Row 36"/38" And 12 Row 30" GA Harness, 670", 12 Row 36"/38" And 16 Row 30" 12. GA Extension Harness, 180" 13. GA Power Lead Adapter 14. GA Harness W/Fuse Holder And Fuse, 132" GD Fuse Holder GD Fuse, 2 Amp Delay Action G1K268 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (1) Lock Ring, (3) Female Terminal Pins 15. GA Pin Female Connector Kit, Includes: (1) 4-Pin Female Housing, (4) Pin Contacts, (4) Seals) 16. GA Pin Male Connector Kit, includes: (1) 4-Pin Male Housing, (4) Sockets, (4) Seals 17. G Whiz Lock Bolt, ¼"-20 x ¾" 18. GD Manifold 19. GD Gasket 20. G Whiz Lock Bolt, ⅜"-18 x 1" 21. GA Cover 22. G Hex Head Cap Screw, ⅜"-16 x 4" G Washer, ⅜" SAE G Lock Nut, ⅜" GD Discharge Deflector 24. GA Screen 25. GD Hub 26. GA Impeller 27. GD Backing Plate 28. G Hex Socket Head Cap Screw, 5 16"-18 x ¾", Grade G Carriage Bolt, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" See Vacuum Fan Hydraulic Motor Assembly, Page P GA Shroud See Vacuum Fan Motor Valve Block Assembly (Located Below Vacuum Fan Assembly), Page P G Washer, ⅝" SAE G Hex Jam Nut, ⅝"-18, Grade G Hex Head Cap Screw, ⅜"-16 x 3 ¼" G Lock Washer, ⅜" A. GA Vacuum Fan Assembly (Items On This Page And Items 1-3, 8 And 9 On Pages P42 And P43) P45 10/08

46 VACUUM FAN HYDRAULIC COMPONENTS (PLTR176) Y Hitch Only See PTO Pump Drive And Oil Cooler Option, pages P52 and P53, if equipped with that option. T Hitch Only With PTO Pump Drive And Oil Cooler Option P46 10/08

47 VACUUM FAN HYDRAULIC COMPONENTS 1. - See Vacuum Fan Hydraulic Motor Assembly, Page P48 2. *A Hose Assembly, ⅜" x 17" 3. *A Hose Assembly, ½" x 13 ½" 4. *A Hose Assembly, ⅜" x 174", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 218", 12 Row 30", Y Hitch *A Hose Assembly, ⅜" x 268", 16 Row 30" Y Hitch *A Hose Assembly, ⅜" x 322", 12 Row 30" T Hitch 5. *A Hose Assembly, ¾" x 174", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¾" x 218", 12 Row 30" Y Hitch *A Hose Assembly, ¾" x 268", 16 Row 30" Y Hitch *A Hose Assembly, ¾" x 322", 12 Row 30" T Hitch 6. *A Hose Assembly, ½" x 173", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 218", 12 Row 30", Y Hitch *A Hose Assembly, ½" x 268", 16 Row 30" Y Hitch *A Hose Assembly, ½" x 322", 12 Row 30" T Hitch 7. GD ISO Coupler 8. *A Hose Assembly, ¾" x 13 ½" 9. - See Vacuum Fan Motor Valve Block Assembly (Located Below Vacuum Fan Motor Assembly), Page P *A Hose Assembly, ⅜" x 120" 11. *A Hose Assembly, ¾" x 120" 12. *A Hose Assembly, ½" x 120" 13. *A Hose Assembly, ⅜" x 100", 8 Row 36"/38" And 12 Row 30" *A Hose Assembly, ⅜" x 110", 16 Row 30" 14. *A Hose Assembly, ¾" x 100", 8 Row 36"/38" And 12 Row 30" *A Hose Assembly, ¾" x 110", 16 Row 30" 15. *A Hose Assembly, ½" x 100", 8 Row 36"/38" And 12 Row 30" *A Hose Assembly, ½" x 110", 16 Row 30" 16. G Lock Nut, 9 16" G Bulkhead Tube Union, 9 16"-18 Male JIC 18. G Lock Nut, " G Bulkhead Tube Union, "-12 Male JIC 20. G Lock Nut, ⅞" G Bulkhead Tube Union, ⅞"-14 Male JIC 22. *A Hose Assembly, ⅜" x 108", 8 Row 36"/38" *A Hose Assembly, ⅜" x 104", 12 Row 30" *A Hose Assembly, ⅜" x 118", 16 Row 30" 23. *A Hose Assembly, ¾" x 108", 8 Row 36"/38" *A Hose Assembly, ¾" x 104", 12 Row 30" *A Hose Assembly, ¾" x 118", 16 Row 30" 24. *A Hose Assembly, ½" x 108", 8 Row 36"/38" *A Hose Assembly, ½" x 104", 12 Row 30" *A Hose Assembly, ½" x 118", 16 Row 30" * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for quote. P47 10/08

48 VACUUM FAN HYDRAULIC MOTOR ASSEMBLY (METR21a) 1. GA Hydraulic Motor GR Seal Kit 2. G Elbow W/O-Ring, 90, ⅞"-14 Male JIC To "-12 O-Ring GR O-Ring 3. G Elbow W/O-Ring, 90, "-12 Male JIC To O-Ring GR O-Ring 4. G Swivel Elbow, 90, 9 16"-18 Male JIC To Female 5. G Connector W/O-Ring, 9 16"-18 Male JIC To O-Ring GR O-Ring OPTIONAL FLOW CONTROL NEEDLE VALVE KIT (A11650) 1. G1K426 - Needle Valve Kit W/Instructions P48 10/08

49 VACUUM FAN MOTOR VALVE BLOCK ASSEMBLY (Located Below Vacuum Fan Motor Assembly) (A11068d) 1. GA Check Valve 2. G Plug W/O-Ring, 9 16"-18 O-Ring GR O-Ring 3. G Plug W/O-Ring, "-12 O-Ring GR O-Ring 4. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 5. G Connector W/O-Ring, 9 16"-18 Male JIC To O-Ring GR O-Ring 6. G Connector W/O-Ring, "-12 Male JIC To O-Ring GR O-Ring 7. GD Valve Block 8. GA Relief Valve Cartridge 9. G Hex Head Cap Screw, ⅜"-16 x 3 ¼" G Lock Washer, ⅜" 10. GD Adapter, ¼" NPT To ⅜" Barb 11. G Hose Clamp, No GD Clear Plastic Tubing, 9 16" O.D. x 60" P49 10/08

50 MANIFOLDS AND DISTRIBUTION HOSES (PLTR175b) 12 Row 30" Shown 1. GD Manifold, 21" (Open One End) 2. GD Pipe, 6" x 11", 8 Row 36"/38" GD Pipe, 6" x 6", 12 Row 30" GD Pipe, 6" x 11", 12 Row 30" GD Pipe, 6" x 11", 16 Row 30" 3. GD Clamp 4. G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" GA Mount 6. GD Manifold, 21" (Open Both Ends) 7. G Cap, 2" 8. G T-Bolt Clamp, 7" 9. G T-Bolt Clamp, 7 ¼" 10. GD Hose, 7" x 21" 11. GA Manifold, 33 ¼", 8 Row 36"/38" GA Manifold, 21 ¾", 12 Row 30" And 16 Row 30" P50 10/08

51 MANIFOLDS AND DISTRIBUTION HOSES 12. GA Manifold, ", 8 Row 36"/38" GA Manifold, ", 12 Row 30" And 16 Row 30" 13. G T-Bolt Clamp, 5 ¼" 14. GA Fan Mount 15. G Hex Head Cap Screw, ¾"-10 x 3", Full Thread G Washer, ¾" USS G Hex Nut, ¾" G Hex Head Cap Screw, ⅝"-11 x 7 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GD Sleeve, ⅝" I.D. x ⅞" O.D. x 5 ¾" Long GD Sleeve, 1 ¾" x 3 ⅛" GD Sleeve, 1 ¾" x 2 ½" 18. GD Hose, 2" x 50" (Pull Row Unit And Even-Row Push Row Unit) GD Hose, 2" x 38" (Push Row Unit) GD Hose, 2" x 44" (Push Row Unit) GD Hose, 2" x 42" (Push Row Unit) 19. GD Elbow, 90, 2" 20. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" See Digital Vacuum Gauge, Analog Vacuum Gauge And Vacuum Fan Assembly, Pages P44 And P G Hex Head Cap Screw, ⅝"-11 x 4 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GA Fan Strut 24. G Hex Head Cap Screw, ¾"-10 x 3", Full Thread G Hex Nut, ¾" GD Support 26. G Hex Head Cap Screw, ⅝"-11 x 10" G Washer, ¾" USS G Lock Washer, ⅝" G Hex Nut, ⅝" GD Hose, 5" x 48" 28. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Washer, 5 16" G Hex Nut, 5 16" GD Support, 21 ½" 30. GD Spacer, 1 ½" x 9" 31. GD Manifold Rail, 37 ½", L.H. Main Frame, 12 Row 30" And 16 Row 30" GD Manifold Rail, 36 ½", R.H. Main Frame, 12 Row 30" And 16 Row 30" GD Manifold Rail, 47 ¾", L.H. Main Frame, 8 Row 36"/38" And 12 Row 36"/38" GD Manifold Rail, 47 ¾", R.H. Wing, 8 Row 36"/38" And 12 Row 36"/38" 32. GD Manifold Rail, 47 ¾", R.H. Wing, 8 Row 36"/38" GD Manifold Rail, 47 ¾", L.H. Wing, 8 Row 36"/38" GD Manifold Rail, 87 ½", L.H. And R.H. Wing, 12 Row 30" GD Manifold Rail, 142 ½", L.H. And R.H. Wing, 16 Row 30" 33. GD Gasket 34. GA Outlet, 5" 35. G Hex Head Cap Screw, ¼"-20 x ¾" G Lock Nut, ¼"-20, Grade B 36. GD U-Bolt, 5" x 7" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" G Hose Clamp, No. 36, Stainless Steel 38. GD Tube, 6 ⅝" x 2" P51 10/08

52 PTO PUMP DRIVE AND OIL COOLER OPTION (TWL302a/D16644/TWL1j/TWL303/PLTR177a) *Return *Pressure *Case Drain *If planter is equipped with a T hitch, see pages P46 and P47 for hoses used between the hoses shown on this page and the bulkhead on the planter hitch. 16 Row 1. G Hex Head Cap Screw, ⅝"-11 x 1 ¾" G Washer, ⅝" USS G Lock Nut, ⅝" G Coil Chain, No. 9/0, 17 Links 3. GD Eyebolt, ⅜"-16 x 4" G Hex Nut, ⅜" GD Anti-Rotation Bracket 5. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" 6. GA PTO Pump 7. G Elbow W/O-Ring, 90, ⅞"-14 Male JIC To "-12 O-Ring GR O-Ring 8. G Elbow W/O-Ring, 90, "-12 Female JIC To O-Ring GR O-Ring P52 10/08

53 PTO PUMP DRIVE AND OIL COOLER OPTION 9. *A Hose Assembly, ½" x 72" 10. *A Hose Assembly, 1" x 72" 11. G Elbow, 90, "-12 Male JIC To 1 ¼" NPT 12. G Elbow, 90, "-12 Male JIC To 1" NPT 13. *A Hose Assembly, ¾" x 25" 14. GA Reservoir W/Breather, 10 Gallon GR Breather 15. GD Strainer 16. G Swivel Elbow, 90, "-12 Male JIC To Female 17. G Adjustable Tee W/O-Ring, "-12 Male JIC To "-12 Male O-Ring To ¾"-16 GR O-Ring 18. *A Hose Assembly, ⅜" x 115", 8 Row 36"/38" *A Hose Assembly, ⅜" x 158", 12 Row 30" *A Hose Assembly, ⅜" x 108", 16 Row 30" 19. G Hex Head Cap Screw, ¼"-20 x ¾" G Lock Washer, ¼" 20. GD Filter Head 21. GD Oil Filter, 10 Micron 22. G Adjustable Tee W/O-Ring, "-12 Male JIC To O-Ring GR O-Ring 23. G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Washer, 5 16" USS G Lock Nut, 5 16"-18, Grade *A Hose Assembly, ¾" x 115", 8 Row 36"/38" *A Hose Assembly, ¾" x 158", 12 Row 30" *A Hose Assembly, ¾" x 108", 16 Row 30" 25. *A Hose Assembly, ¾" x 20" 26. G Elbow W/O-Ring, 90, "-12 Male JIC To ⅞"-14 O-Ring GR O-Ring 27. GA Flow Control Valve 28. G Hex Head Cap Screw, ¼"-20 x 2 ½" G Washer, ¼" USS G Lock Nut, ¼"-20, Grade G Elbow W/O-Ring, 90, ⅞"-14 Male JIC To O-Ring GR O-Ring 30. *A Hose Assembly, ½" x 115", 8 Row 36"/38" *A Hose Assembly, ½" x 158", 12 Row 30" *A Hose Assembly, ½" x 108", 16 Row 30" 31. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 32. GA Mounting Bracket 33. G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS G Lock Nut, ⅜" GA Bracket, 12", 8 Row 36"/38" And 12 Row 30" 35. G Hex Head Cap Screw, ½"-13 x 9 ½" G Lock Washer, ½" G Hex Nut, ½" GD Bracket, 14 ½", 16 Row 30" 37. G Hex Head Cap Screw, ½"-13 x 11 ½" G Lock Washer, ½" G Hex Nut, ½" G Connector W/O-Ring, "-12 Male JIC To O-Ring GR O-Ring 39. GA Oil Cooler 40. GD Bracket 41. *A Hose Assembly, ¾" x 40" See Vacuum Fan Hydraulic Components, Pages P46 And P G Swivel Elbow, 45, "-12 Male JIC To Female * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for quote. P53 10/08

54 OUTER HITCH/SAFETY CHAIN PHA038/PHA025(TWL1h/WGN47a/B0292) Planters Equipped With PTO Pump And Oil Cooler Option 1. GB Clevis, Single (1 ¾" Hole) 2. GA Hitch Mount, 16 Row 30" 3. G Hex Head Cap Screw, 1 ¼"-7 x 6" G Lock Nut, 1 ¼"-7 4. G Hex Head Cap Screw, ¾"-10 x 2 ¾" G Lock Washer, ¾" G Hex Nut, ¾" GD Pin, 1 ¼" x 5 ⅛" G Cotter Pin, 3 16" x 2" 6. G Hex Head Cap Screw, ⅝"-11 x 2 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GA Jack Assembly Complete GA Detent Pin Assembly GR Pin GR Crank Assembly GR Bevel Gear Set, Includes: (2) Bevel Gears, (1) Gear Pin, (1) Groove Pin 8. GA Hitch Mount, 8 Row 36"/38" And 12 Row 30" ( Y Hitch Only) 9. GD Hose Holder 10. GA Detent Pin W/Chain (Transport Latch Locking Pin) 11. See Transport Latch Cylinder, Page P G Hex Head Cap Screw, ⅝"-11 x 2 ¼" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Catch Bar 14. GD Spring 15. GA Transport Latch 16. G Spring Pin, ¼" x 1" 17. G Hex Head Cap Screw, ⅜"-16 x 3" GD Sleeve, 2" Long G Lock Nut, ⅜"-16 P54 10/08

55 OUTER HITCH/SAFETY CHAIN 18. G Washer, ½" USS G Washer, ⅝" USS G Lock Nut, ½" GD Pin, ¾" x 3 ⅜" G Cotter Pin, 5 32" x 1 ½" 20. GD Hose Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 21. GD Hose Clamp, ⅝" x 1 ½" x 1 ½" 22. GD U-Bolt, 3" x 4" x ⅝"-11 G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" See Hose Take-Up, Pages P62 And P GA Roller W/Bronze Bushings, 8 Row 36"/38" Y, 12 Row 30" Y Hitch GA Roller W/Bronze Bushings, 12 Row 30" T Hitch And 16 Row 30" Y GD Bronze Bushing 25. G Lock Nut, ⅜" G Lock Nut, ½" G Hex Head Cap Screw, ¾"-10 x 2" G Lock Nut, ¾" GA Bracket, Jack Mount GD Rubber Pad 29. GA Safety Pin, 12 ¾", 8 Row 36"/38" And 12 Row 30" ( Y Hitch Only) GA Safety Pin, 14 ¾", 16 Row 30" GD Lynch Pin, ¼" GD Lynch Pin, 7 16" 30. G Hex Head Cap Screw, ½"-13 x 1" G Lock Washer, ½" 31. G Hex Head Cap Screw, ½"-13 x 1 ½", 8 Row 36"/38" And 12 Row 30" G Hex Head Cap Screw, ½"-13 x 2", 16 Row 30" G Lock Washer, ½" G Hex Nut, ½" GA Wear Mount, 8 Row 36"/38" And 12 Row 30" ( Y Hitch Only) GA Wear Mount, L.H., 16 Row 30" GA Wear Mount, R.H., 16 Row 30" GA Wear Pad Retainer, 16 Row 30" 33. GD Shim, 4" x 4" (As Required), All Sizes GD Shim, 4" x 6" (As Required), 16 Row 30" 34. GD Wear Pad, Nylatron, 4" x 4" (As Required), All Sizes GD Wear Pad, Nylatron, 4" x 6" (As Required), 16 Row 30" 35. GD Shim, 16 Gauge (16 Row 30" Only) GD Shim, ⅜" (16 Row 30" Only) 36. G Hex Head Cap Screw, ½"-13 x 1" G Lock Washer, ½" G Washer, ½" USS 37. A Outer Hitch, Y, 73", 8 Row 36"/38" (Non-Stock Item) A Outer Hitch, Y, 97", 12 Row 30" (Non-Stock Item) A Outer Hitch, T, 121", 12 Row 30" (Non-Stock Item) A Outer Hitch, Y, 127 ½", 16 Row 30" (Non-Stock Item) A Outer Hitch, T, 151 ½", 16 Row 30" (Non-Stock Item) 38. GD Pin, 1 ¼" x 12", 8 Row 36"/38" Y, 12 Row 30" Y Hitch GD Pin, 1 ¼" x 14", 12 Row 30" T Hitch And 16 Row 30" Y G Spring Pin, ⅜" x 2" 39. GA Safety Chain, ½" G1K412 - Safety Chain Repair Kit, Includes (1) Hook, (1) Flat Washer, (1) Latch Pin, (1) Safety Latch And (1) Retaining Ring 40. G Hex Head Cap Screw, 1 ¼"-7 x 3" GD Special Washer G Washer, 1 ¼" SAE G Lock Nut, 1 ¼" GD Hose Clamp, ⅞" x 3 ½" 42. GA Bracket 43. GD U-Bolt, 3" x 4" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GB Hitch Clevis, Single (2" Pin) P55 10/08

56 2-POINT HITCH OPTION (A12406) P56 10/08

57 2-POINT HITCH OPTION 1. GA Hammer Strap, Category 3N And 3 2. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" 3. GA Hitch Bar 4. GA Pivot Mount 5. GA Pivot Bolt W/Grease Fitting, 1 ¾" x 10 ⅜" (Total Length) G Grease Fitting, ¼"-28 GD Washer, 3" O.D. x " x ¼" Thick GD Sleeve, 3" O.D. x " x 29 32" Thick 6. G Hex Head Cap Screw, ⅝"-11 x 1 ¼" G Washer, ⅝" USS 7. GD Pivot Lock 8. GA Pin, 13 ⅜" 9. GA Hitch Pivot W/Bushings And Grease Fittings GD Hardened Bushing, 2 ¾" O.D. x 2 ¼" I.D. x 3" G Grease Fitting, 90, ¼" G Hex Head Cap Screw, 1"-8 x 2" G Lock Washer, 1" GD Washer, 4" O.D. x " I.D. x ⅜" 11. G Hex Head Cap Screw, 1 ¼"-7 x 6" G Lock Nut, 1 ¼" GD Washer, 4" O.D. x 2 ¼" I.D. x ¼" P57 10/08

58 INNER HITCH, Y PHA035/PHA037(TWL2i) P58 10/08

59 INNER HITCH, Y 1. G Hex Head Cap Screw, ½"-13 x 1", 8 Row 36"/38" And 12 Row 30" G Hex Head Cap Screw, ½"-13 x 1 ½", 16 Row 30" G Lock Washer, ½", 16 Row 30" 2. GD Wear Pad, Nylatron, 4" x 4" GD Shim, 4" x 4" 3. G External Washer 4. GD Shaft, 1 ¼" x 6 ⅜", 8 Row 36"/38" And 12 Row 30" GD Shaft, 1 ¼" x 7 ⅜", 16 Row 30" 5. GA Tongue Hook W/Grease Fittings, 8 Row 36"/38" And 12 Row 30" GA Tongue Hook W/Grease Fittings,16 Row 30" G Grease Fitting, ⅛" NPT 6. GD Pin, 1 ¼" x 12", 8 Row 36"/38" And 12 Row 30" GD Pin, 1 ¼" x 14 ½", 16 Row 30" G Cotter Pin, ⅜" x 2" 7. GD Hose Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 8. See Hose Take-Up, Pages P62 And P63 9. G Hex Head Cap Screw, ½"-13 x 3 ½" G Lock Nut, ½" G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Hose Clamp 12. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Washer, ⅜" USS G Lock Nut, ⅜" GD Shield (If Applicable) 14. GD Pin, 1 ¼" x 5 ⅛" G Cotter Pin, 3 16" x 2" 15. G Square Head Set Screw, 5 16"-18 x ¾" 16. GB Shoe 17. GD Shaft, 1 ¼" x 7", 8 Row 36"/38" And 12 Row 30" GD Shaft, 1 ¼" x 8", 16 Row 30" 18. A Inner Hitch, 145 ⅜", 8 Row 36"/38" (Non-Stock Item) A Inner Hitch, 169 ⅜", 12 Row 30" (Shown) (Non-Stock Item) A7426 Inner Hitch, 205 ⅜", 16 Row 30" (Non-Stock Item) See Tongue Cylinder, Pages P See Tongue Lock Cylinder, Page P GD U-Bolt, 2 ⅛" x 1 ⅞" x ⅜"-16 G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Sleeve 24. GD Shim, 2 ½" x 10", 7 Gauge GD Shim, 2 ½" x 10", 10 Gauge GD Shim, 2 ½" x 10", 12 Gauge P59 10/08

60 INNER HITCH, T PHA035/PHA036(TWL3f) P60 10/08

61 INNER HITCH, T 1. G Hex Head Cap Screw, ½"-13 x 1", 12 Row 30" 2. GD Wear Pad, Nylatron, 4" x 4" GD Shim, 4" x 4" 3. G External Washer 4. GD Shaft, 1 ¼" x 6 ⅜", 12 Row 30" 5. GA Tongue Hook W/Grease Fittings, 12 Row 30" G Grease Fitting, ⅛" NPT 6. GD Pin, 1 ¼" x 12", 12 Row 30" G Cotter Pin, ⅜" x 2" 7. - See Hose Take-Up, Pages P62 And P63 8. GD Pin, 1 ¼" x 5 ⅛" G Cotter Pin, 3 16" x 2" 9. G Square Head Set Screw, 5 16"-18 x ¾" 10. GB Shoe 11. GD Shaft, 1 ¼" x 7", 12 Row 30" 12. A Inner Hitch, 145 ⅜", 12 Row 30" (Shown) (Non-Stock Item) See Tongue Cylinder, Pages P98-P See Tongue Lock Cylinder, Page P GD U-Bolt, 2 ⅛" x 1 ⅞" x ⅜"-16 G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Sleeve 18. GD Shim, 2 ½" x 10", 7 Gauge GD Shim, 2 ½" x 10", 10 Gauge GD Shim, 2 ½" x 10", 12 Gauge P61 10/08

62 HOSE TAKE-UP PHA039(TWL137TWL137f) P62 10/08

63 HOSE TAKE-UP 1. G Carriage Bolt, ⅝"-11 x 2" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Take-Up, 28 ¼", 8 Row 36"/38" Y Hitch GA Take-Up, 44 ¼", 12 Row 30" Y Hitch (Shown) GA Take-Up, 56 ¼", 12 Row 30" T Hitch And 16 Row 30" Y Hitch 3. GD Hose Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 4. G Hex Head Cap Screw, ½"-13 x 2 ¼" G Hex Head Cap Screw, ½"-13 x 2 ½" G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 2 ¼" G Lock Nut, ½" GA Take-Up, 28 ¼", 8 Row 36"/38" Y Hitch GA Take-Up, 44 ¼", 12 Row 30" Y Hitch (Shown) GA Take-Up, 67 ⅝", 16 Row 30" T Hitch 7. GD Cover, 12 Row 30" Y / T Hitch And 16 Row 30" Y (Shown) GD Cover, 8 Row 36"/38" Y Hitch 8. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Washer, ⅜" SAE G Hex Nut, ⅜" G Hex Head Cap Screw, ⅜"-16 x 5" G Washer, ⅜" USS G Lock Nut, ⅜" See Valve Block - Located On Hitch, Page P GA Take-Up, 56 ¼", 12 Row 30" T Hitch And 16 Row 30" Y Hitch P63 10/08

64 CENTER FRAME PFA070/VVB034(TWL138b) 12 ROW 30" SHOWN P64 10/08

65 CENTER FRAME 1. G Hex Nut, ½"-13 G Hex Socket Set Screw, ½"-13 x 1 ¼" 2. G Machine Bushing, 3 ⅛" x 2 ⅛" x 3 16" (As Required) G Machine Bushing, 2 ⅛", 10 Gauge (As Required) G Machine Bushing, 2 ⅛", 14 Gauge (As Required) 3. GD Hinge Pin, 2 ⅛" x 25 ¾" 4. GD Adjustment Block 5. G Hex Head Cap Screw, ¾"-10 x 3 ¾" G Washer, ¾" USS G Lock Nut, ¾" GA Safety Hook 7. GD Pin, 1 ¼" x " 8. G Washer, ⅝" SAE G Lock Nut, ⅝" GD Spring 10. GD Pin, 1 ¼" x 6" 11. GA Spring Rod 12. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Washer, ½" SAE G Lock Washer, ½" GD Sleeve, ½" x ½" Long 13. GA Pad Holder W/Bars GD Bar, 1 ¼" x 6" x ¼" Thick GD Bar, 1 ¼" x 6" x ⅜" Thick G Hex Head Cap Screw, ⅜"-16 x 1" 14. GD Wear Pad, 7" x 7", ½" Thick 15. GD Special Washer, ⅝", Hardened G Hex Nut, ⅝" GD Cap 17. GD Hose Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 18. G Hex Head Cap Screw, ½"-13 x 2 ½" G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ¾"-10 x 3", Full Thread G Hex Nut, ¾" See Valve Blocks - Located On R.H. Rear Center Frame, Page P A Frame W/Cam Follower Mounts, 136" (Non-Stock Item) GA Cam Follower Mount, L.H. GA Cam Follower Mount, R.H. 22. G Hex Head Cap Screw, ¾"-10 x 1 ½" 23. GB Spring Washer 24. GD Sleeve 25. GA Cam Follower W/Grease Fitting G Grease Fitting, ¼" GD Valve Box Mount (If Applicable) 27. GD U-Bolt, 5 16"-18 (If Applicable) G Hex Nut, 5 16"-18 (If Applicable) G Lock Washer, 5 16" (If Applicable) 28. See Valve Box Module, Pages P116 and P117 (If Applicable) 29. G Hex Head Cap Screw, ¼"-20 x 1" (If Applicable) G Lock Washer, ¼" (If Applicable) GD Sleeve, ½" Long (If Applicable) G Hex Nut, ¼"-20 (If Applicable) P65 10/08

66 HYDRAULIC DRIVE PACKAGE OPTION (VI56) P66 10/08

67 HYDRAULIC DRIVE PACKAGE OPTION 1. GD U-Bolt, 3" x 3" x ½"-13 G Hex Nut, ½" GD Spacer 3. GA Motor Bracket 4. G Flangette 5. G Bearing, ⅞" Hex Bore, Spherical 6. G Hex Head Cap Screw, ⅜"-16 x ¾" 7. GD Hex Spacer 8. G Machine Bushing, 1", 10 Gauge 9. See Valve Block - Located On L.H. Rear Center Frame, Pages P G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Washer, 5 16" G Hex Nut, 5 16" G Hex Head Cap Screw, ¼"-20 x 1 ½" G Lock Nut, ¼"-20, Grade B 12. G Hex Head Cap Screw, ⅝"-11 x 4" G Hex Nut, ¼" G Hex Head Cap Screw, ½"-13 x 1 ½" G Hex Nut, ½" G Chain, No. 40, 84 Pitch Including Connector Link GR Connector Link, No GD Spring 16. GA Idler W/Sprocket And Hardware GA Sprocket W/Bearing, 19 Tooth G Hex Head Cap Screw, ½"-13 x 1 ½" G Machine Bushing, ½", 14 Gauge G Hex Jam Nut, ½"-13, Grade 2 GD Idler Arm 17. GA Sprocket, 15 Tooth 18. GD Coupler, 1" I.D. 19. G Chain, Double No. 40, 16 Pitches GR Connector Link, Double No GD Coupler, ⅞" Hex 21. G Hex Head Cap Screw, ⅜"-16 x 1" G Hex Nut, ⅜" GA Sprocket, 30 Tooth 23. GA Hanger Bearing, ⅞" Hex Bore 24. GA Hex Lock Clamp Assembly 25. GA Encoder Module 26. G Hex Socket Set Screw, ¼"-20 x ⅜" 27. GA Hex Adapter Encoder 28. GD Encoder Bracket 29. GD Carrier Bracket 30. GD Hex Shaft, ⅞" x 54 ¾" (No Holes), 12 R 30" P67 10/08

68 WING FRAME (TWL180a/TWL139g) WITH INTERPLANT PACKAGE OPTIONS NOTE: Installed On Even-Row Push Row Unit 1. GA Light Bracket (Wide Row Sizes Only) 2. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Light Bracket (Wide Row Sizes Only) 5. G Hex Head Cap Screw, ¼"-20 x 1" G Lock Nut, ¼"-20, Grade B 6. - See Electrical Components, Pages P114 And P115 P68 10/08

69 WING FRAME 7. GD Hose Clamp, 9 16" x 2 ½" x 2" 8. G Lock Nut, ⅜" GD Pin, 1 ¼" x 9" G Cotter Pin, ¼" x 2" 10. A Wing, R.H., 75 ½", 8 Row 36"/38" (Non-Stock Item) A Wing, L.H., 75 ½", 8 Row 36"/38" (Non-Stock Item) A Wing, R.H., 119 ¼", 12 Row 30" (Non-Stock Item) A Wing, L.H., 119 ¼", 12 Row 30" (Non-Stock Item) A Wing, R.H., 179 ¼", 16 Row 30" (Two Wheel Towers Per Wing) (Non-Stock Item) A Wing, L.H., 179 ¼", 16 Row 30" (Two Wheel Towers Per Wing) (Non-Stock Item) 11. GA Link 12. GD Strap, 56", 8 Row 36"/38" GD Strap, 41", 12 Row 30" And 16 Row 30" 13. GD Pin, 1 ¼" x 10 ½" G Machine Bushing, 1 ¼", 10 Gauge G Cotter Pin, ¼" x 2" 14. GA Toggle Link 15. GD Pin, 1 ¼" x 7" G Machine Bushing, 1 ¼", 10 Gauge G Cotter Pin, ¼" x 2" See Wing Lock Cylinder, Page P GD Pin, 1 ¼" x 7" G Spring Pin, ¼" x 2" 18. GD Bracket 19. GD Pin, 1 ¼" x 5" G Cotter Pin, ¼" x 2" 20. G Detent Pin, ½" x 3 ½" Grip 21. GD Push Row Unit Light Bracket 22. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 3 ½" G Washer, ½" SAE G Lock Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 7" G Lock Washer, ⅝" G Hex Nut, ⅝" GD Mounting Bracket 26. G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" GD Light Mount Extension 28. G Hex Head Cap Screw, ¼"-20 x 1" G Lock Washer, ¼" G Hex Nut, ¼" GA Light Bracket 30. GB Light Mount Bracket A. G7698X - Push Row Unit Mounted Light Bracket Package (Items 21 And 22 On This Page And 42" Harness Extension, Item 5 On Pages P114 And P115) P69 10/08

70 CENTER PIVOT PFA067/PFA068(TWL7c) P70 10/08

71 CENTER PIVOT 1. - See Center Lift Cylinder, Page P96 2. GA Hook Strap 3. GD Sleeve, 3 ⅝" GD Sleeve, " 4. G Hex Head Cap Screw, ⅝"-11 x 5 ½" G Lock Nut, ⅝" G Carriage Bolt, ⅝"-11 x 2" G Lock Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 2 ½" GD Special Washer, 25 32" I.D. x 1 ¼" O.D., Hardened 7. GA Pin, 2 ⅛" 8. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GR Pin, 1" x 3 ½" GR Hair Pin Clip 10. GA Center Post 11. G Hex Head Cap Screw, ⅞"-9 x 3", Grade 8 GD Hardened Washer, ⅞" G Hex Nut, ⅞"-9, Grade GA Cone 13. GA Bearing Housing W/Cups, Less Grease Fitting GD Cup G Grease Fitting, 90, ¼" GD Shim,.005" Thick (As Required) GD Shim,.020" Thick (As Required) GD Shim,.007" Thick (As Required) 15. GD O-Ring 16. GD Bearing Cap P71 10/08

72 AXLE ASSEMBLY HTA043/HTA044/PFA071/PHA033/PHA034/PFA073(TWL140cc) P72 10/08

73 AXLE ASSEMBLY 1. GD Lynch Pin, ¼" 2. G Hex Head Cap Screw, ¾"-10 x 2 ¾" G Hex Head Cap Screw, ¾"-10 x 3" G Lock Washer, ¾" G Hex Nut, ¾" GA Manual Safety Lockup W/Detent Pin GA Detent Pin W/Chain 4. GA Bulkhead Mount 5. GD Pin G Lock Washer, 7 16" G Hex Nut, 7 16" GA Cable, 8 Row 36"/38" GA Cable Assembly, 12 Row 30" And 16 Row 30" 7. G Lock Washer, ½" G Hex Nut, ½" G Lock Nut, ¾"-16 G Lock Nut, ⅞" GD Pin, 1 ¼" x 5 ¼" G Washer, 1 ¼" SAE G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Lock Nut, ⅜" See Rotation Cylinder, Page P G Hex Head Cap Screw, ¾"-8 x 2 ½", Grade 8, Y Hitch G Hex Head Cap Screw, ¾"-10 x 3 ½", Grade 8, T Hitch GD Special Washer, 25 32" I.D. x 1 ¼" O.D., Hardened G Hex Nut, ¾" GD Pin, 1 ¼" x 5 ¼" G Cotter Pin, ¼" x 2" 13. GA Axle W/Stub Axle, 12 Row 30" And 16 Row 30" GA Stub Axle, Narrow Row GA Axle W/Stub Axle, 8 Row 36"/38" GA Stub Axle, Wide Row 14. GD Scraper 15. G Carriage Bolt, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, 1"-8 x 10", Grade 8, Y Hitch G Hex Head Cap Screw, 1"-8 x 11", Grade 8, T Hitch GD Special Washer, " I.D. x 2" O.D. G Hex Nut, 1"-8, Grade G Carriage Bolt, ½"-13 x 1 ½" G Lock Washer, ½" G Hex Nut, ½" GD Cable Gaurd (If Applicable) P73 10/08

74 TRANSPORT WHEELS/ROCK GUARDS HTA032/HTA040/HTA043/HTA004(TWL141c) P74 10/08

75 TRANSPORT WHEELS/ROCK GUARDS (Per Assy.) 1. G Hex Head Cap Screw, ⅞"-9 x 2 ½", Grade 8 G Lock Washer, ⅞" 2. GA Spindle W/Retaining Ring, 1 ¾" G External Retaining Ring, 2 ½" 3. GA Seal 4. GA Bearing 5. GA Hub W/Cups, Bolts, Nuts And Grease Fitting, 8 Bolt, 1 ¾" Bore G Grease Fitting, ¼"-28 GD Cup GR Stud, ⅝"-18 x 2 ¼", Grade 8 6. GD Special Nut, 1 ¾"-12 UNF 7. GD Special Hex Nut, 1 ¾"-12 UNF 8. GA Rim, 5.5" x 22.5", All Sizes 9. GD Tire, R 22.5" W/O Center Rib, Tubeless (Specify Brand*) 10. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Lock Washer, ½" G Hex Nut, ½" GA Rock Guard (Optional) 12. GA Valve Stem 13. GD Lug Bolt, ⅝"-18 x 2 ¾" (If Applicable) 14. GD Jump Start Wheel (If Applicable) 15. G Hex Head Cap Screw, ¼"-20 x ⅝" (If Applicable) G Lock Washer, ¼" (If Applicable) G Hex Nut, ¼"-20 (If Applicable) 16. GD Sensor Bracket Cover (If Applicable) 17. GA Hall Effect Sensor (If Applicable) 18. GA Sensor Bracket (If Applicable) A. GA Tire And Rim Assembly (Items 8, 9 And 12) (Specify Brand*) B. GA Sensor Bracket Assembly (Items 15-18) (If Applicable) * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. P75 10/08

76 CONTACT WHEEL AND DRIVE SHAFT(S) (PLTR155/TWL11e/TWL11k/PLTR150/TWL11f) 16 Row 8/12 Row P76 10/08

77 CONTACT WHEEL AND DRIVE SHAFT(S) (TWL157/TWL156) See Pages P66 And P67 See Pages P66 And P67 B B 8/12 Row (L.H. Side) 16 Row (L.H. Side) (Per Assy.) 1. GD SMV Sign 2. G Hex Head Cap Screw, ¼"-20 x ½" G Lock Washer, ¼" G Hex Nut, ¼" GD Bracket 4. GD Cover 5. GD Spring 6. - See Hydraulic Hoses And Fittings On Planter Frame, Pages P112 And P See Inner Module Drive, Page P83 8. GD Hex Shaft, ⅞" x 13", See Point Row Clutch, Pages P84-P87 (For 8 And 12 Row Machines Equipped With Point Row Clutches) 9. G Spring Pin, ¼" x 1 ½" 10. G Hex Head Cap Screw, ⅜"-16 x 10" (Used To Secure Point Row Clutch) G Lock Nut, ⅜" GA Sprocket, 30 Tooth 12. G Machine Bushing, 1", 10 Gauge G Machine Bushing, 1", 14 Gauge 13. G Hex Head Cap Screw, ⅝"-11 x 4" G Hex Nut, ⅝"-11 G Lock Nut, ⅝" G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GA Pin, 2 ⅛" 16. G Clevis Pin, ⅜" x 1" G Retaining Ring, ⅜" See Wing Lift Cylinder, Page P GA Spring W/Plug 19. GD Lynch Pin, ¼" 20. GA Sprocket, 22 Tooth GA Sprocket, 28 Tooth GA Sprocket, 44 Tooth (Continued On Following Page) P77 10/08

78 CONTACT WHEEL AND DRIVE SHAFT(S) (Per Assy.) (Continued) 21. GD Hex Shaft, ⅞" x 11 ¾" (2 Holes) 22. GA Flanged Bearing, ⅞" Hex Bore 23. G Carriage Bolt, 5 16"-18 x 1" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Idler W/Sprocket And Hardware, L.H. Side Of Planter GA Idler W/Sprocket And Hardware, R.H. Side Of Planter GA Sprocket W/Bearing, 18 Tooth G Hex Head Cap Screw, ½"-13 x 1 ½" G Machine Bushing, ½", 14 Gauge G Hex Jam Nut, ½"-13, Grade G Hex Head Adjusting Bolt, ½"-13 x 4", Grade 2 G Hex Jam Nut, ½"-13, Grade GD Tire, 4.80" x 8", 4 Ply, Rib Implement (Specify Brand*) 27. GA Rim, 3.75" x 8" GD Valve Stem 28. G Machine Bushing, 1", 10 Gauge 29. GA Wheel Arm 30. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 31. GD Shield 32. G Hex Head Cap Screw, ⅝"-11 x 1 ¾" G Machine Bushing, ⅞", 14 Gauge GD Special Washer, ⅝", Hardened G Washer, ⅝" SAE G Lock Nut, ⅝" GD Hinge, Female GD Hinge W/Pins, Male 34. G Hex Head Cap Screw, ¼"-20 x 1" G Washer, ¼" USS G Lock Washer, ¼" G Hex Nut, ¼" GD Hex Shaft, ⅞" x 29 ⅝" 36. G Cotter Pin, 3 16" x 1" 37. GD Spring 38. GA Block And Hub Assembly 39. GD L-Pin 40. GA Sprocket, 30 Tooth 41. G External Retaining Ring, 1 ¼" 42. G Chain, No. 40, 114 Pitch Including Connector Link (Used With 22 Tooth Sprocket) G Chain, No. 40, 118 Pitch Including Connector Link (Used With 28 Tooth Sprocket) G Chain, No. 40, 126 Pitch Including Connector Link (Used With 44 Tooth Sprocket) GR Connector Link, No GD Coupler, 1 ¾", 16 Row 30" Only See Point Row Clutch, Pages P84-P87 A. GA Tire And Rim Assembly (Items 26 And 27) (Specify Brand*) B. GA Ratchet/Sprocket Assembly, L.H. Side Of Planter (Items 36-41) GA Ratchet/Sprocket Assembly, R.H. Side Of Planter (Items 36-41) C. G1K324 - Contact Wheel Arm Replacement Kit (Items 9, 21-23, 25, 28 And 29) * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any change in contact tires. P78 10/08

79 GROUND DRIVE WHEEL PTD057(TWL142c/TWL142d) (Per Assy.) 1. GD Pin, 1 ¼" x 13 ¼" 2. GA Wheel Module 3. G Spring Pin, ⅜" x 2" 4. GD Pin, 1 ¼" x 5 ⅝" G Washer, 1 ¼" SAE G Cotter Pin, ¼" x 2" 5. G Hex Head Cap Screw, ¾"-10 x 2" G Lock Washer, ¾" 6. G Hex Head Cap Screw, ¾"-10 x 2" G Lock Washer, ¾" G Hex Nut, ¾" GD Scraper Arm (If Applicable) 8. GA Spindle W/Round External Retaining Ring, 10" GD Round External Retaining Ring 9. GA Bearing 10. GR Lug Bolt, 9 16" GA Hub W/Cups, 6 Bolt GR Cup 12. G Hex Jam Nut, 1 ½"-12, Grade GD Tire, 7.50" x 20", 8 Ply, Tubeless W/O Center Rib (Specify Brand*) 14. GA Valve Stem 15. GA Rim, 5.5" x 20" 16. GD Bar Clamp (If Applicable) 17. G Hex Head Cap Screw, ½"-13 x 1 ½" G Hex Head Cap Screw, ½"-13 x 1 ¾" G Lock Washer, ½" G Hex Nut, ½" G Carriage Bolt, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Scraper 20. GA Scraper A. GA Tire And Rim Assembly (Specify Brand*) (Items 13-15) B. GA Hub And Spindle Assembly (Items 8, 9, 11 And 12) * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. P79 10/08

80 SEED RATE TRANSMISSION AND ROW UNIT DRILL SHAFTS (TWL14o) 8/12 Row Shown (Per Side) 1. GD Shaft, ⅞" x 15" 2. GD Lynch Pin, ¼" 3. GA Sprocket, 15 Tooth GA Sprocket, 17 Tooth GA Sprocket, 19 Tooth GA Sprocket, 23 Tooth GA Sprocket, 24 Tooth GA Sprocket, 25 Tooth GA Sprocket, 26 Tooth GA Sprocket, 27 Tooth GA Sprocket, 28 Tooth GA Sprocket, 30 Tooth 4. G Spring Pin, ¼" x 1 ½" 5. G Clevis Pin, ⅜" x 1" G Retaining Ring, ⅜" 6. G Hex Head Cap Screw, ½"-13 x 2 ¼" GD Sleeve, 1" O.D. x 9 16" I.D. x ⅞" G Lock Washer, ½", Internal/External G Lock Nut, ½" GD Spring 8. GA Sprocket Storage Rod 9. GB Coupler See Inner Module Drive, Page P GD Coupler, 1 ¾", 16 Row 30" Only 12. GD Hex Shaft, ⅞" x 31 ⅜", 16 Row 30" Only 13. G Square Head Set Screw, 5 16"-18 x ¾" 14. G Square Head Set Screw, ⅜"-16 x ⅝" 15. GD Shear Coupler 16. G Cotter Pin, 3 16" x 2" 17. G Chain, No. 40, 80 Pitch Including Connector Link GR Connector Link, No GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth G Hex Head Cap Screw, ⅜"-16 x 1 ¾" GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" P80 10/08

81 SEED RATE TRANSMISSION AND ROW UNIT DRILL SHAFTS (Per Side) 19. GD Shaft, ⅞" x 13 ½" 20. G Carriage Bolt, 5 16"-18 x 1" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Special Bearing 22. G Flangette 23. G Bearing, ⅞" Hex Bore, Spherical 24. GA Sprocket, 19 Tooth, Interplant Package Drive 25. GD Lock Clamp 26. GD Hex Shaft, ⅞" x 58 ½" (No Holes), Wing, 8 Row 36"/38" GD Hex Shaft, ⅞" x 106 ½" (No Holes), Wing, 12 Row 30" GD Hex Shaft, ⅞" x 166 ¾" (No Holes), Wing, 16 Row 30" 27. GA Hanger Bearing, ⅞" Hex Bore 28. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 29. G Machine Bushing, 1", 10 Gauge 30. GA U-Joint W/Grease Fitting, Female, 18 ⅛" Long, 8 Row 36"/38" And 12 Row 36"/38" GA U-Joint W/Grease Fitting, Female, 10 ¼" Long, 12 Row 30" And 16 Row 30" GR Grease Fitting, 45, Metric GR Inboard Yoke And Outer Profile (18 ¼" U-Joint) GR Inboard Yoke And Outer Profile (10 ¼" U-Joint) GR Cross And Bearing Kit GR Yoke, ⅞" Hex 31. GA U-Joint W/Grease Fitting, Male, 12 ¼" Long GR Grease Fitting, 45, Metric GR Inner Profile GR Inboard Yoke GR Spring Pin, 8 mm x 50 mm GR Cross And Bearing Kit GR Yoke, ⅞" Hex 32. GD Hex Shaft, ⅞" x 53" (No Holes), R.H. Main Frame, 8 Row 36"/38" GD Hex Shaft, ⅞" x 44" (No Holes), L.H. Main Frame, 8 Row 36"/38" GD Hex Shaft, ⅞" x 45" (No Holes), R.H. Main Frame, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 35" (No Holes), L.H. Main Frame, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 38" (No Holes), L.H. Main Frame, 12 Row 30" And 16 Row 30" (If Applicable) (Air Clutch) 33. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Tightener Shaft, 3 ⅜" 35. GD Handle 36. G Vinyl Cap 37. G Hex Socket Button Head Cap Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 38. G Machine Bushing, ⅞", 14 Gauge 39. G External Inverted Snap Ring, 1 ½" 40. G External Inverted Snap Ring, ⅞" 41. GD Sleeve, 1 ¼" 42. GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench)(Shown) GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) 43. GD Release Collar, Gray, L.H. (Shown) GD Release Collar, Blue, R.H. A. G1K269 - Lock Clamp Kit (Items 25 And 28) B. G1K381 - Wrap Spring Wrench Replacement Kit, Gray Collar, L.H. (Items 34-43) (Shown) G1K380 1 Wrap Spring Wrench Replacement Kit, Blue Collar, R.H. (Items 34-43) P81 10/08

82 BOLT-ON WHEEL MODULE/TRANSPORT LATCH CATCH PFA072(TWL15a) 8 Row 36"/38" (Per Side) 1. GD U-Bolt, 5" x 7" x ¾"-10 G Lock Washer, ¾" G Hex Nut, ¾" GA Wheel Tower W/Grease Fitting, L.H. GA Wheel Tower W/Grease Fitting, R.H. G Grease Fitting, ¼" GA Transport Latch Catch 4. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" P82 10/08

83 INNER MODULE DRIVE PTD058/PFA046/PTD077(TWL16e) 16 Row (Per Module) 1. - See Seed Rate Transmission And Row Unit Drill Shafts, Pages P80 And P See Contact Wheel And Drive Shaft(s), Pages P76-P78 3. G Hex Head Cap Screw, ⅝"-11 x 3 ¾" G Machine Bushing, ⅝", 14 Gauge (As Required) G Hex Jam Nut, ⅝"-11, Grade 2 G Lock Nut, ⅝" GA Idler W/Sprocket And Hardware, L.H. Side Of Planter GA Idler W/Sprocket And Hardware, R.H. Side Of Planter GA Sprocket W/Bearing, 18 Tooth G Hex Head Cap Screw, ½"-13 x 3" GD Spacer, 1 ⅛" Long G Washer, ½" SAE G Lock Nut, ½" GD Spring 6. GA Sprocket, 50 Tooth 7. G Hex Head Cap Screw, ½"-13 x 2 ¼" GD Bushing, 1" O.D. x 9 16" I.D. x 7 16" Long G Machine Bushing, ½", 7 Gauge G Washer, ⅝" SAE G Lock Nut, ½" GA Sprocket W/Bearing, 18 Tooth 9. GA Sprocket, 28 Tooth 10. G Spring Pin, ¼" x 1 ½" 11. G Chain, No. 40, 100 Pitch Including Connector Link GR Connector Link, No G Clevis Pin, ⅜" x 1" G Retaining Ring, ⅜" P83 10/08

84 POINT ROW CLUTCH PRC019(TWL70d/TWL71d/TWL71/TWL18/ A10054) L.H. Point Row Clutch Shown (Used On L.H. Side Of Planter) Input Shaft Connects To Clutch Solenoid Connects To Planter Harness At Valve Block On Rear Center Frame On Point Row Clutch P84 10/08

85 POINT ROW CLUTCH (Per Assy.) 1. GD Input Shaft, R.H. Threads (Shown) GD Input Shaft, L.H. Threads 2. G Hex Socket Head Cap Screw, ¼"-20 x 1" G Lock Washer, ¼" 3. G External Inverted Snap Ring, 1 ½" 4. GD V-Ring Seal 5. GD Input Hub 6. GA Hub/Sleeve Assembly W/Spring Pins G Spring Pin, ¼" x 1" G Spring Pin, 5 32" x ⅞" 7. G Hex Head Cap Screw, ¼"-20 x ¾" G Lock Washer, ¼" G Hex Nut, ¼" GA Solenoid Complete GR Snap Ring GR Spring GR Boot GR Plunger 9. G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Hex Nut, ⅜"-16 G Washer, ⅜" SAE G Lock Washer, ⅜" G Hex Jam Nut, ⅜"-16, Grade G Hex Socket Head Cap Screw, ¼"-20 x 1 ¾", Grade 8 G Lock Washer, ¼" G Hex Nut, ¼" GD Spring 12. GD Mounting Plate 13. GD Bushing 14. GD Coupler W/R.H. Threads (Shown) GD Coupler W/L.H. Threads 15. GD Felt Washer 16. GD Spring, L.H. (Shown) GD Spring, R.H. 17. GD Stop Collar 18. GD Rue Ring Cotter, 5 16" 19. GD Actuator Arm 20. G Spring Pin, 3 16" x 2 ¼" 21. G Hex Socket Head Screw, No x ½" G Lock Washer, No GD Hex Shaft, ⅞" x 13" 23. GA Wiring Harness, 192", R.H. Side, 8 Row 36"/38" GA Wiring Harness, 228", L.H. Side, 8 Row 36"/38" And R.H. Side, 12 Row 30" GA Wiring Harness, 264", L.H. Side, 12 Row 30" GA Wiring Harness, 252", R.H. Side, 16 Row 30" GA Wiring Harness, 300", L.H. Side, 16 Row 30" 24. GA Ground Cable, Green 25. G Fork Terminal 26. GD Lock Wire, 10", Stainless Steel 27. G Spring Pin, 3 16" x 1 ¼" A. GA Point Row Clutch Assembly, R.H. (R.H. Side Of Machine) (Items 1-21, 24, 26 And 27) GA Point Row Clutch Assembly, L.H. (L.H. Side Of Machine) (Items 1-21, 24, 26 And 27) P85 10/08

86 TWO-SPEED POINT ROW CLUTCH PRC023(FF47b/A7274/TWL71/TWL18/A10054) L.H. Two-Speed Point Row Clutch Shown (Used On L.H. Side Of Planter) Input Shaft Jumper Wire Between Point Row Clutch Solenoids Connects To Planter Harness At Valve Block On Rear Center Frame Connects To Clutch Solenoids P86 10/08

87 TWO-SPEED POINT ROW CLUTCH (Per Assy.) 1. GD Threaded Rod, ¼"-20 x 3 ½" G Hex Nut, ¼"-20 G Lock Washer, ¼" GD Allen Nut, ¼" G Hex Head Cap Screw, ¼"-20 x ¾" G Lock Washer, ¼" G Hex Nut, ¼" GD Threaded Rod, ⅜"-16 x 4 ½" G Lock Nut, ⅜"-16 G Lock Washer, ⅜" G Hex Nut, ⅜" GD Spring 5. GA Hub/Sleeve Assembly W/Seals, Sleeve, Pins And Screws GD Seal GD Sleeve G Hex Socket Set Screw, 5 16"-18 x ¾" G Hex Socket Set Screw, 5 16"-18 x ¼" G Spring Pin, 5 32" x ⅞" G Spring Pin, ¼" x 1" 6. GD Actuator Arm 7. GD Bushing 8. GA Solenoid Complete GR Snap Ring GR Spring GR Boot GR Plunger 9. GD Mounting Plate 10. G Spring Pin, 3 16" x 2 ¼" 11. G Hex Socket Head Screw, No x ¼" 12. GD Spring, L.H. (Shown) 13. GD Stop Collar 14. GD Felt Washer 15. GA Hub W/Seal GD Seal 16. G External Inverted Snap Ring, 1 ½" 17. GD Output Sprocket, 28 Tooth 18. GD Rue Ring Cotter, 5 16" 19. G Hex Socket Head Cap Screw, ¼"-20 x 1" GD Key 20. GD Input Shaft, R.H. Threads (Shown) GD Input Shaft, L.H. Threads 21. GD Input Sprocket, 28 Tooth 22. GD Coupler W/R.H. Threads (Shown) GD Coupler W/L.H. Threads 23. GA Hub W/Seal GD Seal 24. G Fork Terminal 25. GD Contact 26. GD Housing, Black GD Housing, Red 27. GA Jumper Wire W/Ring Terminals, " 28. GA Wiring Harness, 228", R.H. And L.H. Sides, 8 Row 36"/38" And R.H. Side, 12 Row 30" GA Wiring Harness, 264", L.H. Side, 12 Row 30" GA Wiring Harness, 252", R.H. Side, 16 Row 30" GA Wiring Harness, 300", L.H. Side, 16 Row 30" 29. GD Spring, R.H. P87 10/08

88 TWO-SPEED POINT ROW CLUTCH WHEEL MODULE EXTENSION (TWL77h/TWL84b/TWL79a/TWL80) Output Sprocket TRAVEL See Inner Module Drive Input Sprocket TRAVEL TRAVEL P88 10/08

89 TWO-SPEED POINT ROW CLUTCH WHEEL MODULE EXTENSION (Per Assy.) 1. GD Spring 2. G Spring Pin, ¼" x 1 ½" 3. GA Sprocket, 24 Tooth GA Sprocket, 15 Tooth GA Sprocket, 17 Tooth GA Sprocket, 27 Tooth GA Sprocket, 23 Tooth (From Transmission) GA Sprocket, 25 Tooth (From Transmission) GA Sprocket, 26 Tooth (From Transmission) 4. GA Sprocket, 28 Tooth 5. G Machine Bushing, 1", 10 Gauge 6. G Flangette 7. G Bearing, ⅞" Hex Bore, Spherical 8. G Carriage Bolt, 5 16"-18 x ¾" G Lock Washer, 5 16" G Hex Nut, 5 16" GD Shaft, ⅞" x 13 ¾" 10. GA Extension Bracket 11. G Hex Head Cap Screw, ¼"-20 x 1 ¼" G Washer, ¼" USS G Lock Washer, ¼" G Hex Nut, ¼" G Clevis Pin, 5 16" x ¾" G Retaining Ring, 5 16" 13. G Hex Head Cap Screw, ¼"-20 x 1" G Washer, ¼" USS G Lock Washer, ¼" G Hex Nut, ¼" See Contact Wheel And Drive Shaft(s), Pages P76-P See Two-Speed Point Row Clutch, Pages P86 And P G Chain, No. 40, 74 Pitch Including Connector Link GR Connector Link, No G Chain, No. 40, 100 Pitch Including Connector Link GR Connector Link, No GA Overrunning Sprocket Assembly, R.H. GA Overrunning Sprocket Assembly, L.H. G External Retaining Ring, 1 ¼" GD L-Pin G Spring Pin, 3 16" x 1 ¼" G Cotter Pin, 5 32" x 1" GD Spring GA Block GA Sprocket W/Bushing, 30 Tooth 19. GD Hex Shaft, ⅞" x 13" 20. GA Idler W/Sprocket And Hardware GD Bushing, ¾" Long G Machine Bushing, ½", 14 Gauge G Hex Jam Nut, ½"-13, Grade 2 G Hex Head Cap Screw, ½"-13 x 2 ½" GA Sprocket W/Bearing, 18 Tooth (Continued On Following Page) P89 10/08

90 TWO-SPEED POINT ROW CLUTCH WHEEL MODULE EXTENSION (Per Assy.) (Continued) 21. GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" 22. G Hex Head Cap Screw, ⅝"-11 x 4" G Lock Nut, ⅝"-11 G Hex Nut, ⅝" G Hex Head Cap Screw, ⅜"-16 x 10" G Lock Nut, ⅜" G External Inverted Snap Ring, 1 ½" 25. G External Inverted Snap Ring, ⅞" 26. GD Sleeve, 1 ¼" 27. GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench) (Shown) GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) 28. GD Release Collar, Gray, L.H. (Shown) GD Release Collar, Blue, R.H. 29. GD Tightener Shaft, 3 ⅜" 30. GD Handle 31. G Machine Bushing, ⅞", 14 Gauge 32. G Hex Socket Button Head Cap Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 33. G Vinyl Cap 34. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GA Sprocket Storage Rod 36. GD Lynch Pin, ¼" A. G1K381 - Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 24-33) (Shown) G1K380 1 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 24-33) P90 10/08

91 ROW MARKER SPINDLE/HUB/BLADE MKR020(MKR4) (Per Assy.) 1. G Hex Head Cap Screw, ½"-20 x 1" G Lock Washer, ½" 2. GD Retainer 3. GD Disc Blade, Solid, 16" (Shown) GD Disc Blade, Notched, 16" (Optional) 4. GD Dust Cap 5. G Slotted Hex Nut, ⅝" G Cotter Pin, 5 32" x 1" 7. G Washer, ⅝" SAE 8. GA Bearing 9. GA Hub W/Cups, 4 Bolt GR Outer Cup GR Inner Cup 10. GA Bearing 11. GA Grease Seal 12. GA Rubber Seal 13. GA Spindle, R.H. GA Spindle, L.H. (Shown) 14. G Carriage Bolt, ½"-13 x 3 ½" G Machine Bushing, ½", 7 Gauge G Lock Washer, ½" G Hex Nut, ½" GA Depth Band 16. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Nut, 5 16"-18, Grade 8 A. GA Hub And Spindle Assembly, L.H. (Items 1, 2 And 4-13) GA Hub And Spindle Assembly, R.H. (Items 1, 2 And 4-13) P91 10/08

92 ROW MARKER ASSEMBLY, 8 ROW 36"/38" AND 12 ROW 30" MKR019/MKR027(MKR14i/A11590) P92 10/08

93 ROW MARKER ASSEMBLY, 8 ROW 36"/38" AND 12 ROW 30" (Per Assy.) 1. GA Arm W/Grease Fittings, Second Stage, 110", 12 Row 30" G Grease Fitting, ⅛" NPT GA Arm, Second Stage, 67", 8 Row 36"/38" 2. G Washer, 1 ¼" SAE (As Required) G Machine Bushing, 1 ¼", 10 Gauge (As Required) G Machine Bushing, 1 ¼", 18 Gauge (As Required) 3. GA Pin W/Grease Fitting, 1 ¼" x " G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" 4. GA Arm, First Stage 5. GD Sleeve, 1" 6. GA Safety Lockup W/Detent Pins, 19 ⅜" G Detent Pin, ½" x 2 ½" Grip 7. G Hex Head Cap Screw, ⅝"-11 x 5 ½" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 5" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 2" (If Applicable) GD Special Washer, ⅝", Hardened G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" GD Extension Tube, 45", 12 Row 30" GD Extension Tube, 60", 12 Row 30" (L.H. Even-Row Marker) (If Applicable) GD Extension Tube, 65", 8 Row 36"/38" 9. - See Row Marker (Cushion) Cylinder, Page P GD Pin, 1 ¼" x 8 ¼" G Cotter Pin, ¼" x 2" 11. GA Pin W/Grease Fitting, 1 ¼" x 9 ½" G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" 12. GD Shim, 2 ½" x 7 ¼", 16 Gauge (As Required) 13. GA Mount 14. GA Stand, 20" (12 Row 30" Only) 15. GD U-Bolt, 2" x 2" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Bar 17. GD U-Bolt, 3" x 3" x ½"-13 G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" SAE G Lock Nut, ½" GA Molded Stop, 12 ¼" Long 20. GD Plate, 6" x 6" P93 10/08

94 ROW MARKER ASSEMBLY, 16 ROW 30" MKR019/MKR023MKR027(MKR15jj/A11569) P94 10/08

95 ROW MARKER ASSEMBLY, 16 ROW 30" (Per Assy.) 1. GA Arm, Second Stage, 172 ¼", 16 Row 30" 2. GD Pin, 1 ¼" x 6 ½" G Cotter Pin, ¼" x 2" 3. G Special Washer, 1 ¼" (As Required) G Machine Bushing, 1 ¼", 10 Gauge (As Required) G Machine Bushing, 1 ¼", 18 Gauge (As Required) 4. GA Pin W/Grease Fitting, 1 ¼" x 13" G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" 5. GA Arm, First Stage, L.H. (Shown) GA Arm, First Stage, R.H. 6. GA Safety Lockup W/Detent Pins, 19 ⅜" G Detent Pin, ½" x 2 ½" Grip 7. G Hex Head Cap Screw, ⅝"-11 x 6 ½" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 6" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 2 ½" (If Applicable) GD Special Washer, ⅝", Hardened G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" GD Extension Tube, 75", 16 Row 30" (L.H. Even-Row Marker) (If Applicable) GD Extension Tube, 50", 16 Row 30" 9. - See Row Marker (Cushion) Cylinder, Page P GD Pin, 1 ¼" x 9 ½" G Cotter Pin, ¼" x 2" 11. GA Pin W/Grease Fitting, 1 ¼" x 11 ½" G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" 12. GD Shim, 2 ½" x 12 ½", 16 Gauge (As Required) (Shown) GD Shim, 2 ½" x 8 ¼", 16 Gauge (As Required) 13. GA Mount 14. GA Stand, 30" 15. GD U-Bolt, 2" x 2" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Bar 17. GD U-Bolt, 3" x 3" x ½"-13 G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" SAE G Lock Nut, ½" GA Molded Stop, 12 ¼" Long 20. G Special Washer, 1 ¼" (As Required) 21. GD Plate, 7" x 7" 22. G Washer, 1 ¼" SAE G Machine Bushing, 1 ¼", 18 Gauge P95 10/08

96 ROTATION CYLINDER, ALL SIZES (CYL11i) 1. GA Threaded Ball Joint End 2. G Hex Jam Nut, 1 ¼"-12, Grade 2 3. GD Gland 4. GD Rod 5. GD Piston 6. G Lock Nut, 1 ¼" A Barrel (Non-Stock Item) A. GA Cylinder Complete, 4" x 16" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) U-Cup, (1) Wiper, (1) Seal, (2) Cast Iron Rings, (1) BU Ring, (1) Expander CENTER LIFT CYLINDER, ALL SIZES (CYL39c) Port Type Rephasing 1. GD Clevis 2. G Set Screw, ¼"-20 x ¼" 3. GD Cap 4. GD Rod 5. GD Gland 6. GD Piston 7. G Lock Nut, 1" GA Barrel 9. G Hex Head Cap Screw, ⅜"-16 x 2 ¼" G Lock Nut, ⅜" G6408-H04-O 1 Hex Socket Head Plug W/O-Ring, 7 16"-20 O-Ring GR O-Ring A. GA Cylinder Complete, 3" x 48" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (2) BU Rings, (1) Wiper, (1) U-Cup, (1) Piston Seal, (2) Cast Iron Rings, (1) Expander P96 10/08

97 WING LIFT CYLINDER, 8 AND 12 ROW CYL031/CYL011(CYL45d) ITEM PART NO. QTY DESCRIPTION Port Type Rephasing 1. GA Rod Assembly W/Grease Fitting G Grease Fitting, ¼" GD Gland 3. GD Piston 4. G Lock Nut, 1" A Barrel (Non-Stock Item) A. GA Cylinder Complete, 4 ¼" x 6" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (1) Wiper, (2) O-Rings, (1) BU Ring, (1) U-Cup, (1) Seal, (2) Cast Iron Rings, (1) Expander WING LIFT CYLINDER, 16 ROW CYL031/CYL011(CYL41c) 1. G Set Screw, ¼"-20 x ¼" 2. GD Cap 3. GA Rod Assembly W/Grease Fitting G Grease Fitting, 3 16", Drive-In 4. GD Gland 5. GD Piston 6. G Lock Nut, 1" A Barrel (Non-Stock Item) Port Type Rephasing A. GA Cylinder Complete, 3" x 6" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (2) BU Rings, (1) Expander, (1) Wiper, (1) U-Cup, (1) Piston Seal, (2) Cast Iron Rings P97 10/08

98 TRANSPORT LATCH CYLINDER, ALL SIZES CYL035/CYL050(CYL9c) 1. G Internal Retaining Ring, " 2. GD Gland 3. GD Rod 4. GD Piston 5. G Lock Nut, ½" D Barrel (Non-Stock Item) 7. GD Tension Bushing, 1" x 2" Long 8. GD End Cap A. GA Cylinder Complete, 1 ½" x 2 ½" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (3) O-Rings, (2) BU Rings, (1) Wiper, (1) T-Seal, (1) Bronze Bushing, (1) Seal, (1) U-Cup TONGUE LOCK CYLINDER, ALL SIZES CYL035(CYL9d) 1. G Internal Retaining Ring, " 2. GD Gland 3. GD Rod 4. GD Piston 5. G Lock Nut, ½" D Barrel (Non-Stock Item) 7. GD Tension Bushing, 1" x 2" Long 8. GD End Cap A. GA Cylinder Complete, 1 ½" x 2 ½" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (3) O-Rings, (2) BU Rings, (1) Wiper, (1) T-Seal, (1) Bronze Bushing, (1) Seal, (1) U-Cup P98 10/08

99 TONGUE CYLINDER, 8 ROW 36"/38" WITH Y HITCH (CYL12f) ¾"-16 O-Ring Port 7 16"-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. A Barrel (Non-Stock Item) 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 36" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P99 10/08

100 TONGUE CYLINDER, 12 ROW 30" WITH Y HITCH (CYL12f) ¾"-16 O-Ring Port 7 16"-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. GA Barrel 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 60" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P100 10/08

101 TONGUE CYLINDER, 12 ROW 30" WITH T HITCH, AND 16 ROW 30" WITH Y HITCH CYL036(CYL12f) ¾"-16 O-Ring Port 7 16"-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. GA Barrel 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 84" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P101 10/08

102 TONGUE CYLINDER, 16 ROW 30" WITH T HITCH CYL036(CYL12f) ¾"-16 O-Ring Port 7 16"-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. GA Barrel 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 108" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P102 10/08

103 WING LOCK CYLINDER, ALL SIZES CYL032(CYL3f) 1. GA Rod Assembly 2. GD Gland 3. A Barrel (Non-Stock Item) 4. GD Piston 5. G Lock Nut, ⅞"-14 A. GA Cylinder Complete, 2 ½" x " (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (1) T-Seal, (2) O-Rings, (1) BU Ring, (1) U-Cup, (1) Wiper ROW MARKER (Cushion) CYLINDER, ALL SIZES (CYL3d) 1. GA Rod Assembly 2. GD Gland 3. A Barrel (Non-Stock Item) 4. G Cotter Pin, ⅛" x 1 ¾" 5. GD Piston 6. G Slotted Hex Nut, ⅞"-14 A. GA Cylinder Complete, 2 ½" x " (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (1) T-Seal, (2) O-Rings, (1) BU Ring, (1) Cast Iron Ring, (1) Wiper, (1) U-Cup P103 10/08

104 JUNCTION BLOCK - LOCATED ON R.H. SIDE OF CENTER PIVOT VVB036(TWL24k) 1. GD Manifold Block 2. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 3. G Connector W/O-Ring, ⅞"-14 Male JIC To ¾"-16 O-Ring GR O-Ring 4. G Hex Head Cap Screw, ⅜"-16 x 5" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Hose Clamp, ¾" x 4" x 3 ½" 6. G Hex Head Cap Screw, ½"-13 x 6" G Lock Washer, ½" G Hex Nut, ½"-13 P104 10/08

105 VALVE BLOCKS - LOCATED ON R.H. REAR CENTER FRAME VVB034(TWL25e) 1. G Hex Head Cap Screw, 5 16"-18 x 2 ¾" G Lock Washer, 5 16" 2. 2 See Check Valve, Page P See Solenoid Valve, Page P GD Block 5. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 6. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 7. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To ⅞"-14 O-Ring GR O-Ring 8. G Plug W/O-Ring, ¾"-16 O-Ring GR O-Ring 9. 2 See Flow Control Valve, Page P GD Block 11. G6408-H06-O 6 Hex Socket Head Plug W/O-Ring, 9 16"-18 O-Ring GR O-Ring 12. G Connector W/O-Ring, ¾"-16 Male JIC To ⅞"-14 O-Ring GR O-Ring 13. G Plug W/O-Ring, ⅞"-14 O-Ring GR O-Ring 14. GD Sleeve, 1" Long 15. GD Cover 16. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Washer, 5 16" 17. G Hex Head Cap Screw, 5 16"-18 x ½" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Terminal Strip W/Screws, No. 6, 14 Terminal GR Screw, No x ¼" 19. G Phillips Pan Head Machine Screw, No x ¾", Stainless Steel 20. G Phillips Pan Head Machine Screw, No x ¾", Stainless Steel 21. GA Terminal Strip Mount 22. G Phillips Pan Head Machine Screw, No x ½", Stainless Steel 23. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To O-Ring GR O-Ring 24. G6801-L-08 1 Long Elbow W/O-Ring, 90, ¾"-16 Male JIC To O-Ring GR O-Ring P105 10/08

106 VALVE BLOCK - LOCATED ON HITCH VVB035(TWL26f) 1. GD Block 2. - See Solenoid Valve, Page P See Pressure Relief Valve, Page P G Connector W/O-Ring, 9 16"-18 Male JIC To O-Ring GR O-Ring 5. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 6. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 7. G Swivel Elbow, 90, 9 16"-18 Male JIC To Female 8. G Elbow W/O-Ring, 90, 9 16"-18 Male JIC To O-Ring GR O-Ring 9. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To O-Ring GR O-Ring 10. G6408-H06-O 2 Hex Socket Head Plug W/O-Ring, 9 16"-18 O-Ring GR O-Ring See Hose Take-Up, Pages P62 And P GD Terminal Strip Mount 13. G Phillips Flat Head Machine Screw, No x ⅝", Stainless Steel 14. GA Terminal Strip W/Screws, No. 6, 8 Terminal GR Screw, No x ¼" 15. G Phillips Pan Head Machine Screw, No x ⅝", Stainless Steel See Electrical Components, Pages P114 And P115 P106 10/08

107 VALVE BLOCK - LOCATED ON L.H. REAR CENTER FRAME (PNE39a) 1. GA Hydraulic Motor 2. G Elbow W/O-Ring, "-12 Male JIC To ⅞"-14 O-Ring GR O-Ring 3. G6408-H O-Ring Plug 4. GA Proportional Valve 5. GA Coil 6. GR Manual Override 7. G Hex Socket Head Cap Screw, M x 2.75" 8. G Elbow W/O-Ring, 90, ⅞"-14 Male JIC To 3/4"-16 O-Ring GR O-Ring 9. GD Valve Block 10. GD O-Ring 11. GA Check Valve 12. GA Pressure Comp. Valve P107 10/08

108 SOLENOID VALVE VVB019(TWL27c/TWL18/PLTR75c/A9481) Solenoid Valve Holds Load In One Direction 1. GR Special Hex Nut, ½" G1K274 1 Coil Kit W/Contacts, Housings And Fork Terminals GD Housing, Black GD Contact G Fork Terminal 3. GR Cartridge A. G1K275 - Solenoid Valve Kit W/Solenoid Valve, Contacts, Housings And Fork Terminals GD Housing, Black GD Contact G Fork Terminal B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring Contact Fork Terminal Housing FLOW CONTROL VALVE VVB020(TWL28) A. GA Flow Control Valve B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring PRESSURE RELIEF VALVE VVB020(TWL29) A. GA Pressure Relief Valve, 1000 PSI B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring P108 10/08

109 CHECK VALVE VVB020(TWL30) A. GA Check Valve B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring PROPORTIONAL VALVE (TWL322) A. GA Proportional Valve B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring P109 10/08

110 HYDRAULIC HOSES AND FITTINGS ON HITCH (TWL107/TWL107b) Tongue Cylinder A3 B3 Transport Latch Cylinder B5 A5 A4 B4 C2 A5 A3 A2 B2 B3 A1 B1 B5 A6 B6 C1 D1 D2 Valve Bock - Located On Hitch NOTE: See pages P106 for additional information. B6 A6 Tongue Lock Cylinder C1 Hose Support/Junction - Located On L.H. Side Of Center Pivot D1 B1 A4 B4 Rotation Cylinder A1 P110 10/08

111 HYDRAULIC HOSES AND FITTINGS ON HITCH 1. GD ISO Coupler 2. *A Hose Assembly, ½" x 156", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 191", 12 Row 30" Y Hitch *A Hose Assembly, ½" x 250", 12 Row 30" T Hitch *A Hose Assembly, ½" x 246", 16 Row 30" Y Hitch 3. *A Hose Assembly, ⅜" x 156", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 191", 12 Row 30" Y Hitch *A Hose Assembly, ⅜" x 240", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 246", 16 Row 30" Y Hitch 4. *A Hose Assembly, ⅜" x 48", 8 Row 36"/38" Y Hitch (If Applicable) *A Hose Assembly, ⅜" x 72", 12 Row 30" Y Hitch (If Applicable) *A Hose Assembly, ⅜" x 96", 12 Row 30" T Hitch And 16 Row 30" Y Hitch (If Applicable) 5. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 6. *A Hose Assembly, ¼" x 90", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 110", 12 Row 30" Y Hitch *A Hose Assembly, ¼" x 157", 12 Row 30" T Hitch *A Hose Assembly, ¼" x 168", 16 Row 30" Y Hitch 7. G Elbow W/O-Ring, 90, 9 16"-18 Male JIC To ¾"-16 O-Ring GR O-Ring 8. G Swivel Elbow, 45, 9 16"-18 Male JIC To Female 9. G Connector W/O-Ring, 9 16"-18 Male JIC To ¾"-16 O-Ring GR O-Ring 10. *A Hose Assembly, ¼" x 32", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 40", 12 Row 30" Y / T Hitch And 16 Row 30" Y / T Hitch 11. *A Hose Assembly, ½" x 112", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 72", 12 Row 30" T Hitch *A Hose Assembly, ½" x 120", 12 Row 30" Y Hitch *A Hose Assembly, ½" x 128", 16 Row 30" Y Hitch 12. *A Hose Assembly, ⅜" x 116", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 79", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 125", 12 Row 30" Y Hitch *A Hose Assembly, ⅜" x 130", 16 Row 30" Y Hitch 13. G Bulkhead Tube Union, ⅞"-14 Male JIC 14. G Bulkhead Tube Union, ¾"-16 Male JIC 15. *A Hose Assembly, ¼" x 125", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 85", 12 Row 30" T Hitch *A Hose Assembly, ¼" x 130", 12 Row 30" Y Hitch *A Hose Assembly, ¼" x 136", 16 Row 30" Y Hitch 16. *A Hose Assembly, ⅜" x 60", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 68", 12 Row 30" Y Hitch *A Hose Assembly, ⅜" x 79", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 80", 16 Row 30" Y Hitch * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for quote. P111 10/08

112 HYDRAULIC HOSES AND FITTINGS ON PLANTER FRAME (TWL105b) 16 Row Shown (Two Wing Lift Cylinders Per Wing) 8 And 12 Row (One Wing Lift Cylinder Per Wing) A5 B5 Hose Support/Junction - Located On L.H. Side Of Center Pivot NOTE: See pages P110 and P111 for additional information. B1 C1 A1 D1 L.H. Row Marker Cylinder Valve Block - Located On L.H. Rear Center Frame NOTE: See page P107 for additional information. L.H. Wing Lift Cylinder(s) SLAVE D4 L.H. Wing Lock Cylinder A7 B7 C2 Center Lift Cylinder REAR L.H. MASTER D2 D1 D3 D1 Center Lift Cylinder FRONT R.H. MASTER 1. *A Hose Assembly, ⅜" x 260", 8 Row 36"/38" *A Hose Assembly, ⅜" x 272", 12 Row 30" *A Hose Assembly, ⅜" x 332", 16 Row 30" 2. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To O-Ring GR O-Ring 3. G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 4. *A Hose Assembly, ½" x 62", 8 Row 36"/38" *A Hose Assembly, ½" x 58", 12 Row 30" And 16 Row 30" 5. *A Hose Assembly, ⅜" x 62", 8 Row 36"/38" *A Hose Assembly, ⅜" x 58", 12 Row 30" And 16 Row 30" 6. G Tee, ¾"-16 Male JIC, 16 Row 30" 7. *A Hose Assembly, ⅜" x 230", 8 Row 36"/38" *A Hose Assembly, ⅜" x 250", 12 Row 30" *A Hose Assembly, ⅜" x 272", 16 Row 30" 8. *A Hose Assembly, ⅜" x 66" 9. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 10. *A Hose Assembly, ⅜" x 42" 11. G Bulkhead Tee, ⅞"-14 Male JIC To ¾"-16 JIC 12. G Reducer, ⅞"-14 Female JIC To ¾"-16 Male JIC P112 10/08

113 HYDRAULIC HOSES AND FITTINGS ON PLANTER FRAME D1 C1 B1 D1 A1 B1 Junction Block - Located On R.H. Side Of Center Pivot NOTE: See page P104 for additional information. C1 A1 B4 A4 R.H. Row Marker Cylinder R.H. Wing Lift Cylinder(s) SLAVE R.H. Wing Lock Cylinder B6 A6 D5 C3 C2 D4 C3 D5 D2 C1 D3 A5 B6 A7 B7 B1 A1 A4 B4 A6 B6 Valve Block - Located On R.H. Rear Center Frame NOTE: See page P105 for additional information. 13. *A Hose Assembly, ⅜" x 30" 14. *A Hose Assembly, ⅜" x 52" 15. *A Hose Assembly, ⅜" x 40", 16 Row 30" 16. *A Hose Assembly, ½" x 41" 17. *A Hose Assembly, ½" x 30" 18. *A Hose Assembly, ⅜" x 30" 19. *A Hose Assembly, ⅜" x 204", 8 Row 36"/38" *A Hose Assembly, ⅜" x 225", 12 Row 30" *A Hose Assembly, ⅜" x 288", 16 Row 30" 20. *A Hose Assembly, ⅜" x 30" 21. *A Hose Assembly, ⅜" x 168", 8 Row 36"/38" *A Hose Assembly, ⅜" x 186", 12 Row 30" *A Hose Assembly, ⅜" x 216", 16 Row 30" 22. G6400-L-08 - Long Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 23. *A Hose Assembly, ⅜" x 10 ½", 16 Row 30" 24. G Swivel Elbow, 90, ¾"-16 Male JIC To Female 25. GA Hose Assembly, ¾" x 510" 26. GA Hose Assembly, ½" x 510" 27. GD ISO Coupler * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for quote. P113 10/08

114 ELECTRICAL COMPONENTS (TWL19a/TWL18/ELC14/ELC3a/ELC5c/MTR27a/ELC39/TWL26e/ELC8/A9481/ELC12b/MTR27t/A9689b/A10924ELC4/FF27b/FF27c/ELC38/A9201a/A9202a/TWL20g/ELC34/ELC35/ ELC10c) Socket Contact (Tractor) Pin Contact (Planter) Sealing Plug Amber Amber Red See Wing Frame, pages P68 and P69 for light brackets. For Planter Harness For Tractor Harness See Digital Vacuum Gauge, Analog Vacuum Gauge And Vacuum Fan Assembly, pages P44 and P45 for vacuum gauge electrical components. Harness Extension Planter Harness Tractor Harness 1. GA Ground Clamp 2. GD Contact 3. GD Housing, Black GD Housing, Red 4. GA Double Light Assembly (Shown) GA Double Light Assembly GR Red Lens GR Amber Lens GR Cover GR Rubber Grommet (4) GR Lamp Unit GR Bulb 5. GA Harness Extension, 42" 6. GD Sealing Plug, No GD Socket Contact, No GD Pin Contact, No. 14 P114 10/08

115 ELECTRICAL COMPONENTS 9. GA Wiring Harness W/7 Terminal Female Connector, 786" (2 Light Connections), 12 Row 30" GA Wiring Harness W/7 Terminal Female Connector, 882" (2 Light Connections), 16 Row 30" GA Terminal Female Connector 10. GA Connector W/Cable Clamp, 23 Pin Capacity 11. GA Dust Cap W/Chain 12. GA Dust Cap W/Chain 13. GA Connector W/Cable Clamp, 23 Socket Capacity 14. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 15. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 16. GD Sealing Plug 17. GA Dust Plug (Black) 18. GA Wiring Harness W/Dust Cap, 516", 8 Row 36"/38" And 12 Row 30" GA Wiring Harness W/Dust Cap, 636", 16 Row 30" 19. GA Harness Extension W/Dust Caps, 180" 20. GA Indicator Light 21. GA Fuse Holder W/Spade, " 22. GD Fuse, 15 Amp, Type AGC 23. GD Fuse, MDL 10 Amp Delay Action 24. GR Hex Face Nut, 15 32"-32 GR Internal Tooth Lock Washer, 15 32" 25. GA Cover Plate (Shown) GA Cover Plate, Planters Equipped With Two-Speed Point Row Clutch 26. GR Pan Head Screw, No x ½" 27. GD O-Ring (If Applicable) 28. GA Switch, 3 Position Toggle, On-Off-On 29. GA Switch, 3 Position Toggle, Momentary On-Off-Momentary On 30. GA Switch, 2 Position Toggle, On-Off 31. GA Switch, Push Button W/Transformer 32. GD Mounting Bracket 33. G Washer, ¼" SAE 34. GA Knob 35. GR Cage Nut, ¼" G1K267 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (3) Male Terminal Pins 37. G1K268 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (1) Lock Ring, (3) Female Terminal Pins 38. GA Power Lead Adapter 39. GA Wiring Harness W/Dust Cap And Power Cable 40. G7633X - Backlit Control Console Assembly W/Mounting Brackets, Short Harness W/Dust Cap And Power Cable G7639X - Backlit Control Console Assembly W/Mounting Brackets, Short Harness W/Dust Cap And Power Cable (Planters Equipped With Two-Speed Point Row Clutch) 41. GD Insulated Clamp, ⅜" GD Insulated Clamp, 11 16" 42. GD Jumper, 7 16" 43. GA Jumper Wire W/Fork Terminal, 13" G Fork Terminal 44. GA Wiring Harness W/7 Terminal Female Connector, 714" (4 Light Connections), 8 Row 36"/38" GA Wiring Harness W/7 Terminal Female Connector, 870" (4 Light Connections), 12 Row 36"/38" GA Terminal Female Connector 45. GA Single Amber Light Assembly GR Amber Lens GR Rubber Grommet (2) GR Lamp Unit GR Bulb 46. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 47. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 48. GA Work Light Assembly 49. GD Bracket, 4 ¼" x 4" 50. G T-Bolt Clamp, 3 ½", Stainless Steel 51. GA Wiring Harness, 348" NOTE: See Point Row Clutch or Two-Speed Point Row Clutch for R.H. and L.H. Wiring Harness for the point row clutches. See KPM III Electronic Seed Monitor for those components. P115 10/08

116 VALVE BOX MODULE (A12554) P116 10/08

117 VALVE BOX MODULE 1. GD Straight Union, ¼" 2. GD Strap 3. GA Valve Box Harness 4. GA Manifold 5. GA Valve 6. G Slotted Flat Head Machine Screw, No x ½", Stainless Steel 7. GD Male Connector, ¼" 8. G Phillips Flat Head Machine Screw, No x 1 ½" G Hex Nut, No G Hex Head Cap Screw, ¼"-20 x ½" G Lock Nut, ¼"-20, Grade B 10. GD Nylon Tube, ¼" O.D. x 5" Long 11. GD Hex Nipple, ⅛" Pipe 12. GA Strain Relief 13. GD Valve Box Cover A. GA Valve Box Module Assembly, (Items 1-13) P117 10/08

118 KPM III ELECTRONIC SEED MONITOR (MTR59) Shaft Rotation Sensor Radar Distance Sensor Magnetic Distance Sensor (MDS) Shaft Rotation Sensor Power Lead Adapter Blue Radar Y-Cable Adapter Harness Planter Harness Extension Harness Blue Acre Counter Switch Kit Magnetic Distance Sensor (MDS) Adapter 1. GA Radar Distance Sensor W/20' Cable 2. GA Radar Sensor Pipe/Mounting Bracket Package 3. G1K323-4-Pin Connector Kit W/Female Housing, Includes: (4) Pins, (1) Cable Clamp 4. GA Magnetic Distance Sensor 5. GD Magnetic Distance Sensor Pulse Wheel 6. GD Insulated Clamp, ⅜" 7. GD Bracket 8. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Spring Wave Washer P118 10/08

119 KPM III ELECTRONIC SEED MONITOR 10. GD Mount 11. GA Power Lead Adapter 12. GA Monitor/Radar Adapter Cable, 10" 13. G1K267 - Console Cable Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (3) Male Terminal Pins 14. G1K268 - Console Cable Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (1) Lock Ring, (3) Female Terminal Pins 15. GA KPM III Backlit Console W/Brush (Item 22), Dust Plug (Item 33), Mounting Bracket Assembly, Console Mounting Bracket Hardware And Power Harness GA Mounting Bracket Assembly, Includes: (2) Mounting Brackets, (2) Connector Halves, (1) Compression Spring, (1) Tension Knob, (1) ¼"-20 x 1 ¾" Hex Head Cap Screw, (1) ¼" Plastic Washer, (1) ¼" Steel Washer GR Console Mounting Bracket Hardware Package, Includes: (3) No x ⅝" Hex Socket Pan Head Screws, (3) No. 10 Lock Washers GR Power Harness 16. G1K322-4-Pin Connector Kit W/Male Housing, Includes: (4) Female Socket Contacts And (1) Cable Clamp See Tractor/Planter Wiring Harness, Items 18 And 39 On Pages P114 And P GA Planter Harness W/Dust Caps, 6 Row (9 Connectors) GA Planter Harness W/Dust Caps, 8 Row (12 Connectors) GA Planter Harness W/Dust Caps, 12 Row (16 Connectors) GA Planter Harness W/Dust Caps, 16 Row (20 Connectors) GD Dust Cap 19. GA Seed Tube W/Computerized Sensor GR Sensor Only GA Seed Tube (With Holes For Sensor Installation) 20. GA Magnetic Distance Sensor Adapter (Analog To Digital) 21. GD Shaft Sensor Mount 22. GR Brush 23. GR Radar Y-Cable (Used To Connect Radar Distance Sensor For Multiple Functions) 24. GA Adapter Harness, 1' 25. GA Extension Harness W/Dust Cap, 15' GA Extension Harness W/Dust Cap, 30' GD Dust Cap 26. G1K364 - Rotation Sensor Mount Kit, Includes: (2) Mounts, (2) GD " x 7" U-Bolts, (4) G10228 Lock Washers, (4) G10102 Hex Nuts, (1) Instruction 27. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 28. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 29. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals G1K362-3-Pin Female Connector Kit (Blue), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 30. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals G1K363-3-Pin Male Connector Kit (Blue), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 31. GD Sealing Plug 32. G1K249 - Acre Counter Switch Kit 33. GA Dust Plug (Black) GA Dust Plug (Blue) 34. GA Dust Plug (Black) GA Dust Plug (Blue) 35. GR Rotation Sensor 36. GD Mount 37. G Pan Head Screw, No x 1 ¼" G Washer, No. 10 SAE G Hex Nut, No GD Cover 39. GD Spring 40. GD Spring Mount 41. GR Actuator 42. G Pan Head Machine Screw, No x 1 ¼", Stainless Steel G Lock Washer, No. 8, Internal/External, Stainless Steel G Hex Nut, No. 8-32, Stainless Steel 43. G Hex Head Cap Screw, ⅜"-16 x 8" G Lock Washer, ⅜" G Hex Nut, ⅜"-16 A. GA Magnetic Distance Sensor And Mounting Package (Items 4-9) P119 10/08

120 KINZE COBALT DISPLAY (CO1a/VI18/VI21/A12553/GR1838/GR1839/A12852/A12853) P120 10/08

121 KINZE COBALT DISPLAY 1. *GA Cobalt Display 2. GA Power Supply 3. GA Seed Rate Module 4. GR Flash Card 5. GR SMS CD 6. GA Display Cable 7. GA Power Cable 8. GA Power Control Relay 9. GA Seed Rate Power Cable 10. GA Radar Adapter Cable 11. GA Switch Box Module 12. GR Dust Plug 13. GR Dust Plug 14. GA Mounting Bracket Assembly GD Ram Base GD Ram Vesa Base 15. GA Clutch Control Module 16. GA Implement Cable (12 Row) GA Implement Cable (16 Row) 17. GA Seed Command Cable 18. GA Can Stub Cable, 8'' 19. GA Can Extension, 5'' 20. GA Implement Switch Extension Cable 21. GA Encoder Module 22. GR Switch Box Bracket See Planter Monitor Module (PMM), Pages P124 And P See Planter Monitor Module (PMM), Pages P124 And P GA Hall Effect Sensor 27. GA Limit Switch W/Cable 28. See Center Frame, Pages P64 And P See Pneumatic Down Pressure Package Option And Pull Row Unit, Air Clutch Package Option, Pages P6 And P7 And Interplant Push Row Unit, Air Clutch Package, Pages P42 And P GD Y-Splice Connector 31. GD Terminator 32. GA Seed Rate Cable *See alternate view for mounting bracket. P121 10/08

122 KINZE VISION DISPLAY (VI50a/VI18/VI21/A12553/GR1838/GR1839/A12852/A12853) P122 10/08

123 KINZE VISION DISPLAY 1. *GA Vision Display 2. GA Power Supply 3. GA Null Modem Cable 4. GR Flash Card 5. GR SMS CD 6. GA Display Cable 7. GA Power Cable 8. GA Power Control Relay 9. GA Seed Rate Power Cable 10. GA Radar Adapter Cable 11. *GA Switch Box Module 12. GR Dust Plug 13. GR Dust Plug 14. GA Mounting Bracket Assembly GD Ram Base GD Ram Vesa Base 15. GA Clutch Control Module 16. GA Implement Cable (12 Row) GA Implement Cable (16 Row) 17. GA Seed Command Cable 18. GA Can Stub Cable, 8'' 19. GA Can Extension, 5'' 20. GA Implement Switch Extension Cable 21. GA Encoder Module 22. GR Switch Box Bracket See Planter Monitor Module (PMM), Pages P124 And P See Planter Monitor Module (PMM), Pages P124 And P GA Hall Effect Sensor 27. GA Limit Switch W/Cable 28. GA GPS Cable 29. GA GPS Antenna 30. GD Y-Splice Connector 31. GD Terminator 32. GA Seed Rate Cable 33. GA Seed Rate Module See Center Frame, Pages P64 And P See Valve Block - Located On L.H. Rear Center Frame, Page P See Pneumatic Down Pressure Package Option, Pages P6 And P7 And Interplant Push Row Unit, Air Clutch Package, Pages P42 And P43 *See alternate view for mounting bracket. P123 10/08

124 PLANTER MONITOR MODULE (PMM) (MTR60/MTR63/PMM01/MTR65/MTR61/MTR64/MTR62/PMM02) Shaft Rotation Sensor Magnetic Distance Sensor (MDS) Planter Harness Blue Magnetic Distance Sensor (MDS) Adapter 1. G Hex Head Cap Screw, ⅜"-16 x 8" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Shaft Sensor Mount 3. GR Rotation Sensor 4. GR Actuator 5. GD Mount 6. G Pan Head Screw, No x 1 ¼" G Washer, No. 10 SAE G Hex Nut, No P124 10/08

125 PLANTER MONITOR MODULE (PMM) 7. GD Cover 8. G Pan Head Machine Screw, No x 1 ¼", Stainless Steel G Lock Washer, No. 8, Internal/External, Stainless Steel G Hex Nut, No. 8-32, Stainless Steel 9. GA Magnetic Distance Sensor 10. GD Magnetic Distance Sensor Pulse Wheel 11. GD Insulated Clamp, ⅜" 12. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Bracket 14. GD Spring Wave Washer 15. GA Dust Plug (Black) GA Dust Plug (Blue) 16. GA Dust Plug (Black) GA Dust Plug (Blue) 17. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals G1K362-3-Pin Female Connector Kit (Blue), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 18. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals G1K363-3-Pin Male Connector Kit (Blue), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 19. GD Sealing Plug 20. GA Module Cover Assembly W/Lock Clamps GA Lock Clamp G Phillips Pan Head Machine Screw, No x ⅝", Stainless Steel G Lock Nut W/Nylon Insert, No. 8-32, Stainless Steel 21. GD Bracket 22. GA Planter Monitor Module 23. G Hex Head Cap Screw, 5 16"-18 x 1 ¾" G Lock Washer, 5 16" G Hex Nut, 5 16" See Manifolds And Distribution Hoses, Pages P50 And P G Hex Head Cap Screw, 5 16"-18 x ¾" G Lock Washer, 5 16" G Hex Nut, 5 16" GD Sleeve, ⅞" Long 27. GR Brush 28. GA Planter Harness W/Dust Caps, 8 Row (12 Connectors) GA Planter Harness W/Dust Caps, 12 Row (16 Connectors) GA Planter Harness W/Dust Caps, 16 Row (20 Connectors) GD Dust Cap 29. GA Seed Tube W/Computerized Sensor GR Sensor Only GA Seed Tube (With Holes For Sensor Installation) 30. GA Magnetic Distance Sensor Adapter (Analog To Digital) 31. GA Planter Monitor Module Cable A. GA Magnetic Distance Sensor And Mounting Package (Items 9-14) P125 10/08

126 INTERPLANT PUSH ROW UNIT DRIVE (RU134/TWL516) 8 Row 36"/38" 12 Row 30" If Applicable (Viewed From Front Of Machine) (Per Side) 1. G Machine Bushing, 1", 10 Gauge (As Required) 2. GD Lock Clamp 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 4. GA Hanger Bearing, ⅞" Hex Bore 5. GD Hex Shaft, ⅞" x 55" (No Holes), R.H. Side, 8 Row 36"/38" GD Hex Shaft, ⅞" x 84" (No Holes), L.H. Side, 8 Row 36"/38" GD Hex Shaft, ⅞" x 48" (No Holes), R.H. Side, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 66" (No Holes), L.H. Side, 12 Row 30" And 16 Row 30" 6. GD Hex Shaft, ⅞" x 49" (No Holes), Both Sides, 8 Row 36"/38" GD Hex Shaft, ⅞" x 90" (No Holes), Both Sides, 12 Row 30" GD Hex Shaft, ⅞" x 124" (No Holes), R.H. Side, 16 Row 30" GD Hex Shaft, ⅞" x 138" (No Holes), L.H. Side, 16 Row 30" 7. GD Hex Shaft, ⅞" x 24" (No Holes), 12 Row 30" W/Even-Row Push Row Unit GD Hex Shaft, ⅞" x 33" (No Holes), 16 Row 30" W/Even-Row Push Row Unit 8. GA U-Joint W/Grease Fitting, Female, 18 ⅛" Long, 8 Row 36"/38" And 12 Row 36"/38" GA U-Joint W/Grease Fitting, Female, 10 ¼" Long, 12 Row 30" And 16 Row 30" GR Grease Fitting, 45, Metric GR Inboard Yoke And Outer Profile (10 ¼" U-Joint) GR Inboard Yoke And Outer Profile (18 ⅛" U-Joint) GR Cross And Bearing Kit GR Yoke, ⅞" Hex P126 10/08

127 INTERPLANT PUSH ROW UNIT DRIVE (Per Side) 9. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G External Inverted Snap Ring, 1 ½" 11. G Spring Pin, 5 32" x 7 16" 12. GR Lock Collar 13. GR Spring 14. GR Drive Shaft 15. GR Shim 16. GR Bushing 17. GR Sprocket, 19 Tooth 18. G Hex Socket Set Screw, ⅜"-16 x ¾" 19. GR Pin 20. GR Knurled Collar 21. GR Compression Spring 22. GD U-Bolt, 7" x 5" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Plate (Shown) GD Plate 24. G Chain, No. 40, 226 Pitch Including Connector Link GR Connector Link, No GD Brace 26. GA Sprocket W/Bearing, 18 Tooth 27. G Hex Head Cap Screw, ½"-13 x 2" G Washer, ½" SAE G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 2" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GA Sprocket, 19 Tooth 30. GD Support Angle, R.H. 31. GD Support Angle, L.H. 32. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Coupler, 4" 34. GA U-Joint W/Grease Fitting, Male, 12 ¼" Long GR Grease Fitting, 45, Metric GR Inner Profile GR Inboard Yoke GR Spring Pin, 8 mm x 50 mm GR Cross And Bearing Kit GR Yoke, ⅞" Hex 35. G Hex Head Cap Screw, ⅝"-18 x 2 ¼" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Square Head Set Screw, ⅜"-16 x ⅝" A. GA Clutch Sprocket Assembly, 19 Tooth (Items 10-21) B. G1K269 - Lock Clamp Kit (Items 2 And 3) C. G1K331 - Clutch Sprocket Kit (Items 11, 16 And 17) P127 10/08

128 DOUBLE DISC FERTILIZER OPENER AND MOUNT FOC007(PT25e/TWL34a/FRTZ208) To Pump To Opener Optional - Liquid Fertilizer Only P128 10/08

129 DOUBLE DISC FERTILIZER OPENER AND MOUNT (Per Assy.) 1. GA Bracket 2. G Grease Fitting, ¼"-28, Taper Thread 3. G Cotter Pin, ⅛" x 1" 4. GD Lockup Pin 5. GD Hex Head Adjusting Bolt, ⅝"-18 x 3 ¼" G Hex Jam Nut, ⅝"-18, Grade 2 6. GA Spring 7. GD Bushing, 41 64" I.D. x 3 ½" Long 8. G Machine Bushing, ⅝" (.030" Thick) 9. G Rivet, ¼" x " 10. GD Dust Cap 11. G Hex Jam Nut, ⅝"-11, Grade 2 G Hex Jam Nut, ⅝"-11, L.H. Threads, Grade G Special Machine Bushing, ⅝" x 1" O.D. 13. GB Hub 14. GA Bearing 15. GD Disc Blade, 3.5 mm x 15" 16. GD Inner Scraper 17. GA Mount 18. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Washer, 5 16" 19. GA Drop Tube, Dry Fertilizer 20. GD Extension 21. G Hose Clamp, No GA Drop Tube, Liquid Fertilizer 23. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Washer, 5 16" SAE G Lock Nut, 5 16"-18, Grade GA Shank 25. GA Scraper Mount 26. GD Scraper 27. G Carriage Bolt, ⅜"-16 x 1" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 4 ½" G Lock Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 5" G Lock Nut, ⅝" GD U-Bolt, 2 ½" x 2 ½" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GA Mount W/U-Bolts (One Per Opener) GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Check Valve, Low Rate A. GA Disc Blade And Bearing Assembly (Items 9 And 13-15) P129 10/08

130 HD SINGLE DISC FERTILIZER OPENER (Soil Press Wheel) (TWL35d/TWL35b) P130 10/08

131 HD SINGLE DISC FERTILIZER OPENER (Soil Press Wheel) (Per Assy.) 1. GD J-Bolt, ½"-13 G Lock Washer, ½" G Hex Nut, ½" See HD Single Disc Fertilizer Opener (Blade And Drop Tube), Pages P132 And P GD Lockup Bar 4. G Hex Head Cap Screw, ⅝"-11 x 3" 5. G Flanged Whiz Lock Screw, 5 16"-18 x ⅝", No Serration G Serrated Flange Nut, 5 16" GD Half Wheel Cover, Nylon 7. GA Bearing 8. GD Offset Tire 9. GD Half Wheel 10. G Hex Head Cap Screw, ½"-13 x ¾" G Lock Washer, ½" G Washer, ½" USS 11. G Lock Washer, ⅝" 12. G Machine Bushing, 1" (.048" Thick) 13. G Clevis Pin, ½" x 1 ¾" G Cotter Pin, ⅛" x ¾" 14. GD Yoke 15. G Washer, ⅝" SAE See HD Single Disc Fertilizer Opener (Blade And Drop Tube), Pages P132 And P GD Pivot Pin 18. G Spring Pin, ⅜" x 2" 19. GA Wheel Arm W/Grease Fitting, R.H. GA Wheel Arm W/Grease Fitting, L.H. (Shown) G Grease Fitting, ¼" GD Spring 21. GB Spring Washer 22. GD Special Bolt A. G1K215 - Lockup Kit (Items 1 And 3) B. GA Gauge Wheel Complete (Items 5-9) P131 10/08

132 HD SINGLE DISC FERTILIZER OPENER (Blade And Drop Tube) FOC016/FOC007/FOC019(PT27c/FRTZ208) To Pump To Opener Optional - Liquid Fertilizer Only (Per Assy.) 1. GD Disc Blade, 18" GD Disc Blade, 20" (Optional) 2. GB Spindle 3. GA Seal 4. GA Bearing 5. GA Arm W/Cups And Washers GD Inner Cup GR Outer Cup G Washer, ⅝" SAE 6. G Hex Head Cap Screw, ⅝"-11 x 1 ½" 7. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Nut, ⅜" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 9. GD Channel 10. GD Spring 11. G Grease Fitting, ⅛" NPT 12. G Hex Nut, ¾" GD Tap Block 14. GB Spring Seat 15. GA Bearing 16. G Machine Bushing, ", 10 Gauge 17. G Slotted Nut, 1" GD Dust Cap P132 10/08

133 HD SINGLE DISC FERTILIZER OPENER (Blade And Drop Tube) (Per Assy.) 19. GD Pin G Lock Washer, 7 16" G Hex Nut, 7 16" GD Compression Spring 21. G Hair Pin Clip, No G Bolt, ½"-13 x 1 ½" G Lock Nut, ½" G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Washer, ⅜" USS G Lock Nut, ⅜" G Carriage Bolt, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Scraper 26. GB Drop Tube, R.H., Dry Fertilizer GB Drop Tube, L.H., Dry Fertilizer (Shown) 27. GA Drop Tube, L.H., Liquid Fertilizer (Shown) GA Drop Tube, R.H., Liquid Fertilizer 28. GD Bar 29. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" 30. GD Clamp 31. GD Angle, R.H. GD Angle, L.H. (Shown) 32. G Hex Head Cap Screw, ½"-13 x 2" G Lock Nut, ½" G Machine Bushing, 1 ¼", 18 Gauge (As Required) 34. G Hex Head Cap Screw, ⅝"-11 x 3 ¼" G Washer, ⅝" SAE G Lock Washer, ⅝" 35. G Grease Fitting, ¼" GD Bushing, 2 ¼" 37. G Hex Head Cap Screw, ½"-13 x 1 ¾" G Lock Nut, ½" G Cotter Pin, 3 16" x 1 ½" 39. GA Opener Mount, R.H. GA Opener Mount, L.H. (Shown) 40. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Special Bolt 42. GB Rod Guide 43. GD Storage Strap 44. GD Sleeve, ½" x ½" Long 45. G Washer, ½" USS 46. GA Check Valve, Low Rate P133 10/08

134 NOTCHED SINGLE DISC FERTILIZER OPENER (FRTZ208/B0405/TWL34e/TWL34g/FRTZ268/A12108) To Pump To Opener Optional - Liquid Fertilizer Only Liquid Fertilizer Dry Fertilizer P134 10/08

135 NOTCHED SINGLE DISC FERTILIZER OPENER (Per Assy.) 1. G Hex Head Cap Screw, ½"-13 x 1 ½" G Hex Nut, ½" GB Mount, L.H. GB Mount, R.H. (Shown) 3. GB Arm, 13 ½" 4. G Grease Fitting, ¼" GD Bushing, ¾" O.D. x ½" Long 6. GA Compression Spring Assembly 7. G Hex Head Cap Screw, ⅜"-16 x 1 ¾" G Washer, ⅜" USS G Lock Nut, ⅜" GD Sleeve, " Long 9. GA Pivot Arm, L.H. GA Pivot Arm, R.H. (Shown) 10. GD Scraper, L.H. GD Scraper, R.H. (Shown) 11. G Hex Head Cap Screw, ⅜"-16 x ¾" 12. G Carriage Bolt, ⅜"-16 x 2" G Lock Nut, ⅜" G Hex Head Cap Screw, 5 16"-18 x ⅞" G Lock Washer, 5 16" G Washer, 5 16" USS 14. GD Stepped Spacer, 3" Long 15. GA Hub W/Bearing GA Bearing, Double Row 16. G Hex Head Cap Screw, ⅝"-11 x 5 ½" GD Washer, 1 ½" O.D., 7 Gauge, Hardened G Lock Nut, ⅝" G Hex Head Cap Screw, ⅝"-11 x 5" G Washer, ⅝" USS G Machine Bushing, 1 ½", 18 Gauge (As Required) G Lock Nut, ⅝" GD Disc Blade, Notched, 16 ¾" 19. G Hex Head Cap Screw, ½"-13 x 6" G Washer, ½" SAE G Lock Nut, ½" GD U-Bolt, 1 ½" x 2 ½" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GB Knife, L.H GB Knife, R.H. (Shown) 22. GA Drop Tube, Liquid Fertilizer (Shown) GA Drop Tube, Liquid Fertilizer 23. GA Drop Tube, L.H., Dry Fertilizer GA Drop Tube, R.H., Dry Fertilizer (Shown) 24. GA Check Valve, Low Rate 25. GA Mount W/U-Bolts, Liquid Fertilizer GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Mount W/U-Bolts, L.H., Dry Fertilizer GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Mount W/U-Bolts, R.H., Dry Fertilizer GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝"-11 P135 10/08

136 RESIDUE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER DFC024(FRTZ165l) P136 10/08

137 RESIDUE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER (Per Assy.) 1. - See Notched Single Disc Fertilizer Opener, Pages P134 And P GD Bushing, 1 ⅓" Long 3. GD Adjustment Lever 4. G Spring Pin, ¼" x 1 ¼" 5. G Hex Head Cap Screw, ½"-13 x 7" G Lock Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 7 ½" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GD Sleeve, 2 ⅛" Long 8. GD Spring 9. G Carriage Bolt, ⅜"-16 x 2" G Washer, ⅜" SAE G Lock Nut, ⅜" GA Mount W/Grease Fitting, L.H. (Shown) GA Mount W/Grease Fitting, R.H. G Grease Fitting, ¼" G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade GD Dust Cap 13. GD Wheel, 12 Tine, ⅜" x 12" 14. GA Hub W/Bearings GA Bearing 15. GD Backing Plate 16. GD Spacer, 11 16" I.D. x ½" Long 17. GD Spacer 18. G Carriage Bolt, ⅝"-11 x 3" G Hex Jam Nut, ⅝"-11, Grade GD Spring, L.H. (Shown) GD Spring, R.H. A. GA Wheel Assembly, 12 Tine, L.H. (Items 11 And 13-15)(Shown) GA Wheel Assembly, 12 Tine, R.H. (Items 11 And 13-15) P137 10/08

138 DEPTH/GAUGE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER (FRTZ256) Three Depth Adjustment Holes P138 10/08

139 DEPTH/GAUGE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER (Per Assy.) 1. G Hex Head Cap Screw, ⅝"-11 x 3" 2. GD Special Washer, ⅝", Hardened 3. - See Notched Single Disc Fertilizer Opener, Pages P130 And P GA Blade Mount 5. G Machine Bushing, 1", 10 Gauge 6. GA Wheel Mount, L.H. (Shown) GA Wheel Mount, R.H. 7. GD Spacer 8. GD Half Wheel 9. GD Offset Tire 10. GA Bearing 11. GD Half Wheel Cover, Nylon 12. G Flanged Whiz Lock Screw, 5 16"-18 x ¾", No Serration G Serrated Flange Nut, 5 16" G Special Machine Bushing, ⅝" x 1" O.D. (As Required) A. GA Gauge Wheel Complete (Items 8-12) P139 10/08

140 DRY FERTILIZER DRIVE (TWL37g) (Per Side) 1. G Chain, No. 40, 88 Pitch Including Connector Link GR Connector Link, No GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" 3. GD Shear Coupler 4. G Cotter Pin, 3 16" x 2" 5. GD Shaft, ⅞" x 7 ½" 6. GA Sprocket, 15 Tooth GA Sprocket, 19 Tooth GA Sprocket, 30 Tooth GA Sprocket, 33 Tooth GA Sprocket, 35 Tooth 7. G Spring Pin, ¼" x 1 ½" 8. GA Special Bearing, ⅞" Hex Bore x 1.6" 9. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Lock Nut, ½"-13 P140 10/08

141 DRY FERTILIZER DRIVE (Per Side) 10. GA Sprocket Storage Rod 11. GD Lynch Pin, ¼" 12. GD Shaft, ⅞" x " 13. GD Spring 14 G Grease Fitting, ¼" See Dry Fertilizer Couplers/Shafts, Pages P144 And P GA Bearing, ⅞" Hex Bore, Cylindrical 17. G Machine Bushing, 1", 10 Gauge 18. GD Sleeve, ⅝" I.D. x ⅞" O.D. x 3 ¼" Long 19. GD Sleeve, 1 ¼" O.D. x ⅝" Long 20. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" SAE G Lock Washer, ½" G Hex Nut, ½" G Chain, No. 40, 130 Pitch Including Connector Link GR Connector Link, No GA Sprocket, 30 Tooth 23. G Carriage Bolt, ½"-13 x 4 ½" G Washer, ½" SAE G Lock Nut, ½" GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Lock Nut, ⅜" GD U-Bolt, 7" x 5" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Mount, L.H. (Shown) GA Mount, R.H. 27. GA Transmission Plate, L.H. (Shown) GA Transmission Plate, R.H. 28. GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) (Shown) GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench) 29. GD Handle 30. G Hex Socket Button Head Cap Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 31. G External Inverted Snap Ring, ⅞" 32. G External Inverted Snap Ring, 1 ½" 33. GD Tightener Shaft, 4 ⅞" 34. G Vinyl Cap 35. GD Sleeve, 1 ¼" 36. GD Release Collar, Blue, R.H. (Shown) GD Release Collar, Gray, L.H. 37. GA Sprocket, 22 Tooth A. G1K378 1 Wrap Spring Wrench Replacement Kit, Blue Collar, R.H. (Items 28-36) (Shown) G1K379 - Wrap Spring Wrench Replacement Kit, Gray Collar, L.H. (Items 28-36) P141 10/08

142 DRY FERTILIZER HOPPER AND MOUNTS DFC009/DFC018(TWL36) P142 10/08

143 DRY FERTILIZER HOPPER AND MOUNTS (Per Hopper) 1. GA Lid W/Retainers, Clips, Rivets, Rubber Straps And Hardware GD Front Clip GD Rear Retainer G Rivet, 3 16" x 13 32" GD Rubber Strap G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" GB Auger, R.H. 3. GB Auger, L.H. 4. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" GD Shaft 6. G Hex Head Cap Screw, ¼"-20 x 2", Stainless Steel G Hex Nut, ¼"-20, Stainless Steel 7. GD Strap 8. G Hair Pin Clip, No GD Baffle 10. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Special Washer, ⅜" x 1 ½" O.D. GD Rubber Washer G Lock Washer, 5 16" G Hex Nut, 5 16" G Grease Fitting, ⅛" NPT 13. GD Hopper 14. GD Outlet Housing 15. G Carriage Bolt, 5 16"-18 x 1" G Hex Head Cap Screw, 5 16"-18 x 1 ¼" (If Applicable) G Washer, 5 16" USS (If Applicable) G Special Washer, ⅜" x 1 ½" O.D. GD Rubber Washer G Lock Washer, 5 16" G Hex Nut, 5 16" G Cotter Pin, ¼" x 2" 17. GB Bearing 18. G Hose Clamp, No. 36, Stainless Steel 19. G Hose Clamp, No GD Rubber Tube 21. GD U-Bolt, 7" x 5" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Washer, ½" G Hex Nut, ½" GD Angle, L.H. 24. GA Mount, L.H. 25. GD Angle, R.H. 26. GA Mount, R.H. 27. GD Holder, Rubber Tube (As Required) A. GA Hopper Sub-Assembly (Items 8, 10 And 12-15) B. GA Hopper Hardware Box (Items 2-7, 9, 11, 16 And 17) P143 10/08

144 DRY FERTILIZER COUPLERS/SHAFTS RH100594(TWL38a) 8 Row 36" 8 Row 38" 12 Row 30" 12 Row 36" 12 Row 38" 16 Row 30" L.H. Side Of Machine Shown Direction Of Travel P144 10/08

145 DRY FERTILIZER COUPLERS/SHAFTS 1. - See Dry Fertilizer Drive, Pages P140 And P GD Coupler, 6" 3. G Cotter Pin, ¼" x 2" 4. GA U-Joint W/Grease Fitting, Male, 12 ¼" Long GR Yoke, ⅞" Hex GR Cross And Bearing Kit GR Inboard Yoke GR Inner Profile GR Grease Fitting, 45, Metric GR Spring Pin, 8 mm x 50 mm 5. GA U-Joint W/Grease Fitting, Female, " Long GR Yoke, ⅞" Hex GR Cross And Bearing Kit GR Inboard Yoke And Outer Profile GR Grease Fitting, 45, Metric 6. G Machine Bushing, 1", 10 Gauge 7. GD Coupler, 3" 8. GD Hex Shaft, ⅞" x 15 ½" (1 Hole) 9. G Spring Pin, ¼" x 1 ½" 10. GD Coupler, 1 ¾" 11. GA U-Joint W/Grease Fitting, Female, 10 ¼" Long GR Yoke, ⅞" Hex GR Cross And Bearing Kit GR Inboard Yoke And Outer Profile GR Grease Fitting, 45, Metric 12. GD Coupler, 4" 13. GD Hex Shaft, ⅞" x 24 ½" (1 Hole) 14. GD Hex Shaft, ⅞" x 13 ½" (1 Hole) 15. GD Coupler, 10 ¾" 16. G Square Head Set Screw, ⅜"-16 x ⅝" P145 10/08

146 LIQUID FERTILIZER TANKS, SADDLES, SADDLE MOUNTS AND HOSES LFC021/LFC023/LFC030/LFC012(FRTZ201g) 8" Lid 1 ¼" At Bottom Of Tank ¾" At Bottom And Top Of Tank Polypropylene Fitting Assemblies See Items 5 And G Elbow, 90, ¾" NPT To Barb 2. GD Band, 30" (4 Per Tank) 3. G Hose Clamp, No G Hose, ¾" x 72" (One Per Tank) 5. GA Tank W/Lid And Fittings, 30" x 150 Gallon, 8 Row Sizes (Qty. 2), 12/16 Row Sizes (Qty. 4) GR Lid W/Vent, 8" (Top Of Tank) GR ¾" Polypropylene Fitting Assembly (Overflow Fitting, Nut, Bushing And O-Ring) (Top And Bottom Of Tank) GR Overflow Fitting GR ¼" Polypropylene Fitting Assembly (Nut, Bushing And O-Ring) (Bottom Of Tank) P146 10/08

147 LIQUID FERTILIZER TANKS, SADDLES, SADDLE MOUNTS AND HOSES 6. GD Pad, 8" x 14' (For Two 30" Tanks) 7. GA Tank Mount (2 Per Tank) 8. GD Mounting Angle (2 Per Tank) 9. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 8" G Washer, ¾" USS G Lock Washer, ¾" G Hex Nut, ¾" G Adapter, 1 ¼" NPT To Barb 12. GD J-Bolt, 5 16"-18 (8 Per Tank) G Lock Nut W/Nylon Insert, 5 16"-18, Grade 8 (8 Per Tank) 13. G Hose Clamp, No GA Shutoff Valve, 1 ¼" NPT GR Body O-Ring GR Stem O-Ring GR Teflon Seat GR Ball GR Handle 15. G Elbow, 90, 1 ¼" Male NPT To Female 16. G Close Nipple, 1 ¼" NPT 17. G Pipe Plug, ¾" NPT 18. G Tee, 1 ¼" Barb 19. G Hose, 1 ¼" x 32', 8 Row 36"/38" And 12 Row 30" G Hose, 1 ¼" x 40', 16 Row 30" 20. G Tee, 2" Female NPT 21. G Reducing Bushing, 2" Male NPT To 1 ¼" Female 22. GD Dust Plug, 2" Male Cam Lock 23. GD Adapter, 2" Female NPT To Cam Lock 24. GD Dust Cap, 2" Cam Lock 25. G Elbow, 45, 2" Male NPT To Female 26. GD Adapter, 2" Male NPT To Cam Lock 27. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Shutoff Valve, 2" NPT 29. G Elbow, 90, 2" NPT To Barb 30. G Hose Clamp, No. 36, Stainless Steel 31. G Hose, 2" x 12', 8 Row G Hose, 2" x 18', 12/16 Row 32. GA Quick Fill Mount, 2" 33. G Close Nipple, 2" NPT P147 10/08

148 LIQUID FERTILIZER PISTON PUMP MOUNT AND GROUND DRIVE WHEEL (TWL219rr) 48 Tooth Drive Sprocket And 18 Tooth Driven Sprocket 18 Tooth Sprocket 48 Tooth Sprocket 1. G Hex Head Cap Screw, ⅝"-11 x 7 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GA Wheel Arm Mount 3. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 4. G Hex Head Cap Screw, 5 / 8 "-11 x 1 ¾" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Spring Mount 6. GD Pin, 1 ¼" x 13 ½" G Cotter Pin, ¼" x 2" 7. GA Arm W/Grease Fittings G Grease Fitting, ⅛" NPT 8. GA Wheel, 5" x 15" 9. GD Valve Stem P148 10/08

149 LIQUID FERTILIZER PISTON PUMP MOUNT AND GROUND DRIVE WHEEL 10. G Hex Head Cap Screw, ⅝"-11 x 6 ½" GD Special Washer, ⅝", Hardened 11. GA Spring Mount 12. GB Washer 13. GD Compression Spring 14. GA Spring Guide 15. G Hex Head Cap Screw, ⅝"-11 x 12" G Lock Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 2" G Lock Washer, ¾" 17. G Hex Head Cap Screw, ¾"-10 x 1 ¾" G Lock Washer, ¾" G Hex Nut, ¾" GD Hose Holder 19. GR Sprocket, 18 Tooth 20. G Hex Head Cap Screw, ⅜"-16 x 1 ½" GR Mounting Pad G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜"-16 GR Offset Link, No See Liquid Fertilizer Piston Pump, Pages P152 And P G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Washer, ⅝" USS G Lock Washer, ⅝" G Hex Nut, ⅝" GA Pump Mount 24. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Scraper 26. G Hex Head Cap Screw, ⅝"-11 x 3 ½" G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" GA Idler Sprocket W/Bearing, 15 Tooth 28. GD Spacer, 11 16" I.D. x 1 ¼" Long 29. GD Tire, 7.60" x 15", 8 Ply (Specify Brand*) 30. GA Spindle 31. GA Seal 32. GA Bearing 33. GR Lug Nut, ½" G Sprocket, 48 Tooth 35. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Washer, 5 16" 36. GD Shoulder Nut, 1 ¼"-12 UNF-2A 37. GA Hub W/Cups And Studs, 5 Bolt GR Cup GR Stud 38. G Chain, No. 2050, 63 Pitch Including Connector And Offset Link, Used With NGP-7075 Piston Pump GR Connector Link, No GR0200 `- Offset Link, No GD Lynch Pin, ¼" * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any change in tires. P149 10/08

150 LIQUID FERTILIZER FLOW DIVIDER MOUNT AND HOSES (FRTZ280/FRTZ298) P150 10/08

151 LIQUID FERTILIZER FLOW DIVIDER MOUNT AND HOSES 1. G Hose, ⅜" x 160', 12 Row G Hose, ⅜" x 120', 16 Row 2. G Hose Clamp, No GD Adapter, ¼" NPT To ⅜" Barb 4. - See Liquid Fertilizer Piston Pump Flow Divider, Pages P154 And P G Pipe Plug, ¼" NPT 6. G Reducing Bushing, 1" Male NPT To ¾" Female, Stainless Steel (If Applicable) 7. GA Mount, ¾" NPT 8. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Strainer Complete GR Screen, No. 40 Mesh GR Gasket GR Y-Body GR End Cap 10. G Hose Clamp, No G Adapter, 1 ¼" NPT To Barb See Liquid Fertilizer Tanks, Saddles, Saddle Mounts And Hoses, Pages P146 And P G Hose Clamp, No G Coupler, ¾" Female NPT 15. G Hose, ¾" x 200" 16. G Reducing Bushing, 1 ½" Male NPT To ¾" Female 17. G Elbow, 90, ¾" NPT To Barb See Liquid Fertilizer Piston Pump, Pages P152 And P G Reducing Bushing, 1 ½" Male NPT To 1 ¼" Female 20. G Close Nipple, 1 ¼" NPT 21. G Elbow, 90, 1 ¼" Male NPT To Female P151 10/08

152 LIQUID FERTILIZER PISTON PUMP Uses 18 Tooth Sprocket (A12335a/GR1808) Model NGP-7055 P152 10/08

153 LIQUID FERTILIZER PISTON PUMP Uses 18 Tooth Sprocket 1. GR Flange Cover Assembly G Hex Head Cap Screw, 5 16"-18 x ⅞" 2. GR Connecting Rod Assembly 3. GR Spacer Assembly G Hex Socket Head Set Screw, 5 16"-18 x ⅜" 4. GR Plug 5. GR Vent Plug 6. GR Woodruff Key 7. GR Eccentric Pin 8. GR Pin 9. GR Bearing 10. GR Setting Hub Assembly 11. GR Stuffing Box Insert 12. GR Sprocket, 18 Tooth 13. GR Adjustment Wrench 14. GR Setting Pointer Assembly 15. GR Repair Kit, Includes: (6) Gaskets, (9) O-Rings, (4) Washers, (1) Retaining Ring, (2) Oil Seals, (1) Snap Ring, (1) Thrust Washer, (1) Rod Bushing, (2) Flange Plunger Packings, (2) Packing Springs, (2) Rod Vee Packing Sets 16. GR Discharge Valve Assembly 17. GR Suction Valve Assembly 18. GR Setting Arm Key 19. GR Bearing 20. G Carriage Bolt, ⅜"-16 x 2" G Lock Nut, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜"-16 A. GA Piston Pump Complete W/18 Tooth Sprocket (Model NGP-7055) P153 10/08

154 LIQUID FERTILIZER PISTON PUMP FLOW DIVIDER (FRTZ159/PT40a/FRTZ202c) Model FD-1200 Flow Divider, 12 Outlet Model FD-2000 Flow Divider, 20 Outlet ¾" NPT 1" NPT P154 10/08

155 LIQUID FERTILIZER PISTON PUMP FLOW DIVIDER 1. GR Vent Plug 2. GR Hex Socket Head Screw, ¼"-20 x ¾" GR Lock Washer, ¼", Stainless Steel 3. GR Cap 4. GR Needle Assembly W/Seal Kit (Item 22) 5. GR Seal Kit, Includes: (3) O-Rings, (1) Seal, (1) Spring, (1) Stainless Steel Sleeve 6. GR Sleeve 7. GR Body, 12 Outlets 8. G Hex Socket Head Plug, ¼" NPT, Stainless Steel 9. GR Cap 10. GR Needle Assembly W/Seal Kit (Item 22) 11. GR Seal Kit, Includes: (3) O-Rings, (1) Seal, (1) Spring 12. GR Sleeve 13. GR Body, 20 Outlets 14. GR Sleeve, 1" O.D. x ½" Long, Stainless Steel A. GA Liquid Fertilizer Piston Pump Flow Divider Complete, 12 Outlet (Model FD-1200) (Items 1-7) (8/12 Row Sizes) B. GA Liquid Fertilizer Piston Pump Flow Divider Complete, 20 Outlet (Model FD-2000) (Items 1, 2 And 8-14) (16 Row Size) P155 10/08

156 LIQUID FERTILIZER SQUEEZE PUMP DRIVE (TWL46e) (Per Side) 1. GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" 2. GD Lock Clamp 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 4. G Machine Bushing, 1", 10 Gauge (As Required) 5. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" G Clevis Pin, 5 16" x 1" G Retaining Ring, 5 16" 7. GD Spring 8. GD Hex Shaft, ⅞" x 48" (1 Hole), 8 Row GD Hex Shaft, ⅞" x 54" (1 Hole), 12/16 Row P156 10/08

157 LIQUID FERTILIZER SQUEEZE PUMP DRIVE (Per Side) 9. GA Sprocket, 15 Tooth GA Sprocket, 17 Tooth GA Sprocket, 19 Tooth GA Sprocket, 23 Tooth GA Sprocket, 24 Tooth GA Sprocket, 30 Tooth GA Sprocket, 46 Tooth GA Sprocket, 50 Tooth GA Sprocket, 62 Tooth GA Sprocket, 66 Tooth 10. G Hex Head Cap Screw, 5 16"-18 x 2" G Lock Washer, 5 16" G Hex Nut, 5 16" G Cotter Pin, 3 16" x 2" 12. GD Lynch Pin, ¼" 13. GA Sprocket Storage Rod 14. GD Shear Coupler See Liquid Fertilizer Squeeze Pump, Pages P158-P GA Pump Mount, L.H. 17. GA Pump Mount, R.H. 18. G Bearing, ⅞" Hex Bore, Spherical 19. G Flangette 20. GA Drive Plate W/Grease Fitting GA Drive Plate W/Grease Fitting (Shown) G Grease Fitting, ¼" GD U-Bolt, 7" x 5" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Coupler 24. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G Chain, No. 40, 170 Pitch Including Connector Link GR Connector Link, No See Seed Rate Transmission And Row Unit Drill Shafts, Pages P80 And P GD Sleeve, 1 ¼" 28. GD Release Collar, Gray, L.H. (Shown) GD Release Collar, Blue, R.H. 29. GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench) (Shown) GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) 30. GD Handle 31. G Hex Socket Button Head Cap Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 32. GD Sleeve, 1 ¼" O.D. x ⅝" Long 33. G External Inverted Snap Ring, ⅞" 34. G External Inverted Snap Ring, 1 ½" 35. GD Tightener Shaft, 4 ⅞" 36. G Vinyl Cap A. G1K269 - Lock Clamp Kit (Items 2 And 3) B. G1K379 - Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 27-36) (Shown) G1K378 1 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 27-36) P157 10/08

158 LIQUID FERTILIZER SQUEEZE PUMP, 8 ROW SIZE LFC011(PT46a) 1. GR Spring Anchor Bar 2. GR Spring 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Washer, 5 16" USS G Wing Nut, 5 16" GR Plate 5. GR Nylon Bushing 6. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Wing Nut, 5 16" GR Metering Hose, ½" x 13" 8. G Hose Clamp, No G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Hex Nut, ⅜" GR Angle 11. GR Manifold Plug 12. GR Adapter 13. GR Intake Manifold 14. GR Discharge Manifold Less Hose Barbs 15. G Hose, ⅜" x 120' 16. GR Rubber Cap 17. GR Nylon Washer 18. G Square Head Set Screw, 5 16"-18 x ¾" 19. G Grease Fitting, ¼" GR Roller Arm 21. GR Roller 22. G Spring Pin, 5 16" x 1 ⅛" 23. GD Sleeve 24. GD Shaft 25. GR Shim, 3 64" 26. GR Shim, 1 32" 27. GR Frame 28. GR Nylon Hose Barb, ½" x ⅜" (If Applicable) A. GA Squeeze Pump Complete, 4 Rows (Items 1-14, And 24-28) P158 10/08

159 LIQUID FERTILIZER SQUEEZE PUMP, 12 ROW SIZES LFC011/LFC011(PT47a) 1. GR Spring Anchor Bar 2. GR Spring 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Washer, 5 16" USS G Wing Nut, 5 16" GR Plate 5. GR Nylon Bushing 6. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Wing Nut, 5 16" GR Metering Hose, ½" x 13" 8. G Hose Clamp, No G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Hex Nut, ⅜" GR Angle 11. GR Manifold Plug 12. GR Adapter 13. GR Intake Manifold 14. GR Discharge Manifold Less Hose Barbs 15. G Hose, ⅜" x 160', 12 Row 30" G Hose, ⅜" x 120', 12 Row 36"/38" 16. GR Rubber Cap 17. GR Nylon Washer 18. GR Bushing 19. G Square Head Set Screw, 5 16"-18 x ¾" 20. G Grease Fitting, ¼" GR Roller Arm 22. GR Roller 23. G Spring Pin, 5 16" x 1 ⅛" 24. GD Sleeve 25. GD Shaft 26. GR Shim, 3 64" 27. GR Shim, 1 32" 28. GR Frame 29. GR Nylon Hose Barb, ½" x ⅜" (If Applicable) A. GA Squeeze Pump Complete, 6 Rows (Items 1-13, And 25-29) P159 10/08

160 LIQUID FERTILIZER SQUEEZE PUMP, 16 ROW SIZE LFC010(PT48a) P160 10/08

161 LIQUID FERTILIZER SQUEEZE PUMP, 16 ROW SIZE 1. GR Spring Anchor Bar 2. GR Spring 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Washer, 5 16" USS G Wing Nut, 5 16" GR Plate 5. GR Nylon Bushing 6. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Wing Nut, 5 16" GR Metering Hose, ½" x 13" 8. G Hose Clamp, No GR Adapter 10. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Hex Nut, ⅜" GR Angle, L.H. GR Angle, R.H 12. GR Manifold Plug 13. GR Intake Manifold 14. GR Discharge Manifold Less Hose Barbs 15. G Hose, ⅜" x 120' 16. GR Rubber Cap 17. GR Nylon Washer 18. GR Bushing 19. G Square Head Set Screw, 5 16"-18 x ¾" 20. G Grease Fitting, ¼" GR Roller Arm 22. GR Roller 23. GR Set Collar 24. GR Back Up Roller 25. G Spring Pin, 5 16" x 1 ⅛" 26. GD Sleeve 27. GD Shaft 28. GR Shim, 3 64" 29. GR Shim, 1 32" 30. GR Frame 31. GR Nylon Hose Barb, ½" x ⅜" (If Applicable) A. GA Squeeze Pump Complete, 8 Rows (Items 1-14, And 27-31) P161 10/08

162 REAR TRAILER HITCH PHA032/LFC003(TWL47a) P162 10/08

163 REAR TRAILER HITCH 1. GA Hitch 2. G Hex Head Cap Screw, ⅝"-11 x 1 ½" GD Special Washer, ⅝", Hardened G Lock Washer, ⅝" 3. G Washer, 1 ¼" SAE 4. GD Pin, 1 ¼" x 12 ¾" G Cotter Pin, ¼" x 2" 5. GA Hitch 6. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 7. GD Tap Block 8. GB Spring Seat 9. GD Spring 10. GB Rod Guide 11. GD Special Bolt G Hex Nut, ¾" G Hex Head Cap Screw, 1"-8 x 2 ½" G Lock Nut, 1" GD U-Bolt, 2" x 2" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Hanger Tube 15. GD Spring 16. G Twin Loop Chain, 15 Links 17. GA Hose Support 18. G Hex Head Cap Screw, ¼"-20 x 1" G Washer, ¼" USS G Lock Nut, ¼"-20, Grade B 19. GA Hose Support 20. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Nut, ⅜" G Hose, 1 ¼" x 22' 22. G Hose Clamp, No G Adapter, 1 ¼" NPT To Barb 24. GA Shutoff Valve, 1 ¼" NPT GR Body O-Ring GR Stem O-Ring GR Teflon Seat GR Ball GR Handle 25. GD Adapter, 1 ¼" Male NPT To Cam Lock 26. GD Dust Cap, 1 ¼" Cam Lock 27. GD Adapter, 1 ¼" Barb To Female Cam Lock 28. GD Dust Plug, 1 ¼" Male Cam Lock 29. G Hex Head Cap Screw, ⅜"-16 x 5" G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ⅜"-16 x 6" G Lock Washer, ⅜" G Hex Nut, ⅜"-16 P163 10/08

164 DECALS, PAINT AND MISCELLANEOUS Connect directly to DO NOT REMOVE THIS ASSEMBLY AFTER PLANTER IS ASSEMBLED FOR USE. REMOVAL OF THIS WHEEL AND AXLE ASSEMBLY CAN CAUSE THE MACHINE TO BECOME UNSTABLE AND TIP OVER CAUSING DAMAGE OR SERIOUS INJURY P164 10/08

165 DECALS, PAINT AND MISCELLANEOUS A A 9 P165 10/08