INTERPLANT SYSTEM Interplant Push Row Unit...P38 Interplant Push Row Unit Drive...P110

Transcription

1 PARTS LIST INDEX ROW UNIT 15" Seed Opener Disc Blade/Bearing Assembly And Scrapers...P11 Brush-Type Seed Meter...P21 Coulter Mounted Residue Wheels...P34 Covering Discs/Single Press Wheel...P13 Drag Closing Attachment...P15 Finger Pickup Seed Meter...P20 Frame Mounted Coulter W/Residue Wheels...P36 Gauge Wheels...P12 Granular Chemical Banding Options...P25 Granular Chemical Hopper And Hopper Panel Extension...P22 Granular Chemical Meter And Meter Drive...P24 Hopper Support And Meter Drive...P18 Parallel Arms, Mounting Support Plate And Pneumatic Down Pressure Package Option...P4 Parallel Arms, Mounting Support Plate And Quick Adjustable Down Force Springs Option...P10 Pneumatic Down Pressure Control Box, Sending Unit And Harnesses...P6 Pneumatic Down Pressure Air Compressor, Dual Solenoid Assembly, Tubing And Fittings...P8 Row Unit Mounted Bed Leveler...P28 Row Unit Mounted Disc Furrower...P30 Row Unit Mounted No Till Coulter...P27 Row Unit Mounted Residue Wheel...P32 Seed Hopper And Lid...P19 Shank Assembly, Seed Tube And Depth Adjustment...P2 Spring Tooth Incorporator...P26 V Closing Wheels...P14 BASE MACHINE 2-Point Hitch Option...P42 Axle Assembly...P56 Bolt-On Wheel Module/Transport Latch Catch...P66 Center Frame...P50 Center Pivot...P54 Contact Wheel And Drive Shaft(s)...P60 Cylinders...P80 Electrical Components...P100 Ground Drive Wheel...P63 Hose Take-Up...P48 Hydraulic Hoses And Fittings...P94 Inner Hitch...P44 Inner Module Drive...P67 Outer Hitch...P40 Point Row Clutch...P68 Row Marker Assemblies...P76 Row Marker Spindle/Hub/Blade...P75 Safety Chain...P34 Seed Rate Transmission And Row Unit Drill Shafts...P64 Transport Wheels/Rock Guards...P58 Two-Speed Point Row Clutch...P70 Two-Speed Point Row Clutch Wheel Module Extension...P72 Valve And Junction Blocks...P88 Valves (Solenoid, Flow Control, Pressure Relief, Check)...P92 Wing Frame...P52 ELECTRONIC SEED MONITOR KPM I Electronic Seed Monitor...P102 KPM II Stack-Mode Electronic Seed Monitor...P104 KPM III Electronic Seed Monitor...P106 Planter Monitor Module...P108 INTERPLANT SYSTEM Interplant Push Row Unit...P38 Interplant Push Row Unit Drive...P110 FERTILIZER Dry Fertilizer...P126 Fertilizer Openers, Mounts And Attachments...P114 Liquid Fertilizer...P132 Rear Trailer Hitch...P152 Decals, Paint And Miscellaneous...P154 Numerical Index...P157 P1 Rev. 8/07

2 SHANK ASSEMBLY, SEED TUBE AND DEPTH ADJUSTMENT (METR29cc/D16245) P2 Rev. 8/07

3 SHANK ASSEMBLY, SEED TUBE AND DEPTH ADJUSTMENT (Per Row) 1. G Hex Washer Head Cap Screw, ⅜"-16 x 1 ¼" 2. GB Cover, Depth Adjustment 3. GB Handle, Depth Adjustment 4. GB Lever, Depth Adjustment 5. GD Cap Plug 6. GD Spring 7. GD Pin, ⅜" x 1 ⅔" 8. GD Sleeve, ⅜" I.D. x ⅝" O.D. x " Long 9. G Hex Head Cap Screw, ⅜"-24 x 2 ½", Grade 8 G Lock Nut, ⅜"-24, Grade C 10. G Chain, No. 41, 98 Pitch Including Connector Link G Chain, No. 41, 16 Pitch Including Connector Link (Used W/Row Unit Extension Brackets) GR Connector Link, No GD Sleeve, " Long 12. G Special Washer, ⅜" x 1 ½" O.D. 13. GD Idler Spring 14. GD Sleeve, 1" Long 15. G Lock Nut, ⅜" G Washer, ⅜" USS 17. GD Idler 18. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Lock Nut, ⅜" GD Stop 20. G Hex Head Cap Screw, ⅜"-16 x 3 ¾" 21. G Clevis Pin, ¼" x 2 ½" G Hair Pin Clip, No G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" GD Shield See Gauge Wheels, Pages P12 And P GA Shank W/Gauge Wheel Pivot Spindle And Set Screw GD Spindle G Hex Head Cap Screw, ½"-13 x ¾" 26. G Washer, ⅞" O.D. x 13 32" I.D. x.134" (If Applicable) 27. GD Dust Cap 28. See KPM I Electronic Seed Monitor, KPM II Stack-Mode Electronic Seed Monitor, KPM III Electronic Seed Monitor And Planter Monitor Module, Pages P102-P GB Collar, Depth Adjustment 30. GB Pivot Link, Depth Adjustment 31. GD Sun Shade 32. G Carriage Bolt, ⅜"-16 x 3" G Lock Nut, ⅜" GD Sun Shade (Rubber) P3 Rev. 8/07

4 PARALLEL ARMS, MOUNTING SUPPORT PLATE AND PNEUMATIC DOWN PRESSURE PACKAGE OPTION (RU157a/RU159/RU157aa) Pull Row Unit Shown Push Row Unit Shown P4 Rev. 8/07

5 PARALLEL ARMS, MOUNTING SUPPORT PLATE AND PNEUMATIC DOWN PRESSURE PACKAGE OPTION (Per Row) 1. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Mounting Support Plate 3. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 4. GD Upper Parallel Arm 5. G Hex Head Cap Screw, ⅝"-18 x 2" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Lower Parallel Arm 7. GA Bearing/Sprocket, ⅞" Hex Bore 8. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" See Hopper Support And Meter Drive, Page P GA Air Spring Assembly 11. GB Saddle 12. G Hex Head Cap Screw, ⅝"-18 x 1 ¼" GD Special Washer, ⅝", Hardened GD Sleeve, ⅞" O.D. x ⅝" I.D. x 21 32" 13. GB Head Mount 14. GB Shoulder Nut, ¾" GB Bracket 16. G Hex Socket Cap Screw, ½"-13 x 1 ½" G Serrated Flange Nut, ½" G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" SAE GD Spacer, ¼" G Lock Nut, ⅜" GD Link 19. GB Plate 20. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Washer, ½" SAE (Lower Two Holes Only) G Lock Washer, ½" See Interplant Push Row Unit, Pages P38 And P GB Yoke Mount 23. GB Yoke 24. GB Mount 25. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GB Plate 27. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GB Extension Bracket 29. GB Extension 30. G Hex Head Cap Screw, ½"-13 x 1 ¾" G Washer, ½" SAE G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 1 ¼" G Lock Washer, ½" A. G6325X - U-Bolt Package For 5" x 7" Toolbar, Includes: (2) GD1113, (4) G10230, (4) G10104 P5 Rev. 8/07

6 PNEUMATIC DOWN PRESSURE CONTROL BOX, SENDING UNIT AND HARNESSES (PNE01/MTR27a/ELC27b/MTR45/MTR27t) P6 Rev. 8/07

7 PNEUMATIC DOWN PRESSURE CONTROL BOX, SENDING UNIT AND HARNESSES 1. GA Power Lead Adapter 2. GA Control Box Assembly 3. GA Sending Unit 4. GA Wiring Harness W/Fuse Holder And Fuse, 206" GD Fuse Holder GD Fuse, 2 Amp Delay Action 5. G1K268 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (1) Lock Ring, (3) Female Terminal Pins 6. G1K267 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (3) Male Terminal Pins 7. GA Strain Relief 8. GR Pan Head Screw, No x ½" 9. GR Hex Face Nut, 15 32" GA Switch, 3 Position Toggle, ON-OFF-ON 11. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 12. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 13. GA Pin Female Connector Kit, Includes: (1) 4-Pin Female Housing, (4) Pin Contacts, (4) Seals 14. GA Pin Male Connector Kit, Includes: (1) 4-Pin Male Housing, (4) Socket Contacts, (4) Seals 15. G1K396-6-Pin Female Connector Kit (Black), Includes: (3) 6-Pin Female Housings,(18) Pin Contacts, (18) Seals 16. G1K395-6-Pin Male Connector Kit (Black), Includes: (3) 6-Pin Male Housings, (18) Socket Contacts, (18) Seals 17. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 18. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 19. GA Strain Relief 20. GA Wiring Harness W/Fuse Holder And Fuse, 60' GD Fuse Holder GD Fuse, 20 Amp 21. GA Wiring Harness, 60' See Pneumatic Down Pressure Air Compressor, Dual Solenoid Assembly, Tubing And Fittings, Pages P8 And P9 P7 Rev. 8/07

8 PNEUMATIC DOWN PRESSURE AIR COMPRESSOR, DUAL SOLENOID ASSEMBLY, TUBING AND FITTINGS (PNE06/PNE02/PNE05/A13169/PNE09/PNE08) P8 Rev. 8/07

9 PNEUMATIC DOWN PRESSURE AIR COMPRESSOR, DUAL SOLENOID ASSEMBLY, TUBING AND FITTINGS 1. GD Cover 2. G Phillips Pan Head Machine Screw, No x ¾", Stainless Steel G Serrated Flange Nut, No GA Air Compressor 4. GA Filter Assembly GR Filter 5. GA Mount 6. G Hex Head Cap Screw, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" GD Manifold, ¼" NPT 8. GD Close Nipple, ¼" NPT 9. GD Plug, ¼" NPT 10. GD Reducer, ⅛" Male To ¼" Female 11. GA Tank, 3 Gallon 12. GA Drain, ¼" NPT 13. GR Pressure Switch 14. GA Valve Stem, ⅛" NPT 15. G Slotted Pan Head Machine Screw, M4-0.7 x GA Shutoff Valve, ¼" NPT 17. GD Plug, ¼" NPT 18. GA Breather, ¼" NPT 19. GD Connector, ¼" Male 20. GA Block 21. GD Connector, ¼" Male 22. GA Solenoid 23. GD Female Cross, ¼" NPT 24. GA Pressure Gauge, ¼" NPT 25. GD Swivel Elbow, ¼" NPT x ⅜" 26. GD U-Bolt, 3" x 3" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Bracket 28. G Hex Head Cap Screw, ¼"-20 x 1 ½" G Lock Washer, ¼" G Washer, ¼" USS 29. GD Tee, ⅜" Tube Union 30. GD Nylon Tubing, ⅜" O.D. x 44', 8 Row Pull Row Units GD Nylon Tubing, ⅜" O.D. x 64', 12 Row Pull Row Units GD Nylon Tubing, ⅜" O.D. x 86', 16 Row Pull Row Units GD Nylon Tubing, ⅜" O.D. x 40', 7 Row Push Row Units GD Nylon Tubing, ⅜" O.D. x 60', 11 Row Push Row Units GD Nylon Tubing, ⅜" O.D. x 82', 15 Row Push Row Units GD Nylon Tubing, ⅜" O.D. x 5', Even-Row Push Row Unit 31. GD Elbow, ⅜" x ⅛" NPT Extended See Parallel Arms, Mounting Support Plate And Pneumatic Down Pressure Package Option, Pages P4 And P5 33. GD Tee, ⅜" x ⅛" NPT Extended, Push Row Unit 34. GA Tube Cutter W/Blade GR Blade A. GA Air Compresor Assembly (Items 1-14) B. GA Dual Solenoid Assembly (Items 15-25) P9 Rev. 8/07

10 PARALLEL ARMS, MOUNTING SUPPORT PLATE AND QUICK ADJUSTABLE DOWN FORCE SPRINGS OPTION RUB021/RUB022(RU78f/B0366) (Per Row) 1. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Mounting Support Plate 3. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 4. GD Upper Parallel Arm 5. G Hex Head Cap Screw, ⅝"-18 x 2" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GB Spring Anchor 7. GD Tab Lock Pin, 7 16" x 1 ½" 8. GD Spring 9. - See Hopper Support And Meter Drive, Page P GA Lower Parallel Arm 11. GA Bearing/Sprocket, ⅞" Hex Bore 12. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GB Extension Bracket A. G6325X - U-Bolt Package For 5" x 7" Toolbar, Includes: (2) GD1113, (4) G10230, (4) G10104 P10 Rev. 8/07

11 15" SEED OPENER DISC BLADE/BEARING ASSEMBLY AND SCRAPERS (RU139) (Per Row) 1. G Hex Head Cap Screw, ⅜"-16 x ⅝" G Serrated Flange Nut, ⅜" GA2012R 1 Disc Scraper, R.H. GA2012L - Disc Scraper, L.H. (Shown) 3. G Rivet, ¼" x ½" 4. GD Special Hex Head Cap Screw, ⅝"-11 x 1 ½", L.H. Threads G Hex Head Cap Screw, ⅝"-11 x 1 ½" 5. GD Dust Cap 6. G Special Machine Bushing, ⅝" x 1" O.D. 7. GD Bearing Housing 8. GA Bearing 9. GD Disc Blade, 3.5 mm x 15" 10. G Machine Bushing, ⅝" (.030" Thick)(As Required) See Shank Assembly, Pages P2 And P3 12. GB Seed Tube Guard/Inner Scraper 13. G Hex Socket Head Cap Screw, 5 16"-18 x 1", Grade G Hex Head Cap Screw, ⅜"-16 x 2 ¾" G Serrated Flange Nut, ⅜" GD Sleeve, ⅜" I.D. x ⅝" O.D. x " Long A. GA Disc Blade/Bearing Assembly, Less Dust Cap (Items 3 And 7-9) P11 Rev. 8/07

12 GAUGE WHEELS (RU140) P12 Rev. 8/07

13 GAUGE WHEELS (Per Row) 1. G Machine Bushing, 1" (.048" Thick) 2. G Washer, ½" USS 3. G Lock Washer, ½" 4. G Hex Head Cap Screw, ½"-13 x 1" 5. GD Cover 6. G Carriage Bolt, 5 16"-18 x 1 1 / 4 " G Serrated Flange Nut, 5 16" G Carriage Bolt, 5 16"-18 x 1 ¾" G Serrated Flange Nut, 5 16" G Hex Head Cap Screw, ⅝"-11 x 3" G Lock Washer, ⅝" 9. G Hex Head Cap Screw, 5 16"-18 x ⅝" G Lock Nut, 5 16"-18, Grade GD Half Wheel 11. GD Tire 12. GA Bearing 13. G Special Machine Bushing, ⅝" x 1" O.D. 14. GA Wheel Arm W/Grease Fitting, Bushings And Seals, L.H. (Shown) GA Wheel Arm W/Grease Fitting, Bushings And Seals, R.H. G Grease Fitting, ¼"-28 (Per Arm) GB Bushing, 1" I.D. x 1 ¼" O.D. x 1" Long (Per Arm) GD Seal (Per Arm) See Shank Assembly, Pages P2 And P3 A. GA Gauge Wheel Complete (Items 5-7 And 9-12) B. G1K296 - Gauge Wheel Arm Bushing And Seal Driver Kit, Includes: (1) Seal Driver, (1) Bushing Driver, (1) Instruction P13 Rev. 8/07

14 COVERING DISCS/SINGLE PRESS WHEEL RUA054/RUB026(RU94d) P14 Rev. 8/07

15 COVERING DISCS/SINGLE PRESS WHEEL (Per Row) 1. G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS 2. GB Wheel Arm Stop 3. G Carriage Bolt, ½"-13 x 2 ¼" G Carriage Bolt, ½"-13 x 2 ½" (Used W/Straight Drop In-Furrow Granular Chemical Bracket) G Hex Nut, ½" GA Spring 5. GB Eccentric Bushing 6. G Hex Nut, ½" G Adjusting Bolt, ½"-13 x 5" 8. GA Mounting Arm 9. G Cotter Pin, ¼" x 1 ½" 10. G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Bracket 12. GA Mount 13. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" G Lock Nut, ⅝" GD Bushing, 41 64" I.D. x ⅞" O.D. x ¼" Long 16. GD Disc Blade, 8" 17. G Hex Head Cap Screw, 5 16"-18 x ⅝" G Lock Nut, 5 16"-18, Grade G Hex Head Cap Screw, 5 / 8 "-11 x 9" 19. GD Sleeve, ⅝" I.D. x ⅞" O.D. x 2 ⅞" Long 20. GD Half Wheel 21. GA Bearing 22. GD Tire 23. GA Bearing 24. GD Bearing Housing 25. G Rivet, ¼" x ½" 26. G Hex Head Cap Screw, ⅝"-11 x 2 ¼" 27. GD Dust Cap A. GA Single Press Wheel Complete W/Bearing (Items 17 And 20-22) B. GA Covering Disc Blade Complete W/Bearing (Items 16 And 23-25) P15 Rev. 8/07

16 V CLOSING WHEELS (RU83i/RU83n) (Per Row) 1. G Carriage Bolt, ½"-13 x 2 ¼" G Carriage Bolt, ½"-13 x 2 ½" (Used W/Straight Drop In-Furrow Granular Chemical Bracket) G Lock Nut, ½" GB Wheel Arm Stop 3. G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS 4. GB Stepped Bushing 5. GB Eccentric Bushing 6. GD Spring 7. G Hex Head Cap Screw, ¼"-20 x 1" 8. G Hex Head Cap Screw, ⅝"-11 x 3 ½" G Lock Nut, ⅝" G1K345 - Closing Wheel Shield Kit W/Hardware And Instruction G Carriage Bolt, ⅜"-16 x ¾" G Carriage Bolt, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Nylon Half Wheel 11. GA Bearing 12. GD Rubber Tire, 1" x 12" 13. GD Bushing, 41 64" I.D. x ⅞" O.D. x ¼" Long 14. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade GA Cast Iron Closing Wheel W/Bearing GA Bearing 16. GA Arm 17. GB Lever 18. GD Special Washer, ⅝", Hardened 19. G Lock Washer, ⅝" A. GA Rubber Closing Wheel Complete W/Bearing (Items 7 And 10-12) P16 Rev. 8/07

17 DRAG CLOSING ATTACHMENT RUB050(RU90c) (Per Row) 1. G Carriage Bolt, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Front Bracket 3. GD Blade 4. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GD Rear Bracket A. G7566X - Drag Closing Attachment Complete (Items 1-5) P17 Rev. 8/07

18 HOPPER SUPPORT AND METER DRIVE (METR22d) (Per Row) 1. GB Hopper Mount 2. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 3. G Hex Head Cap Screw, ⅝"-18 x 2 ¼" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Hex Head Cap Screw, ⅝"-18 x 1 ¾" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Spring Pin, ¼" x 1 ½" 6. G External Retaining Ring, ⅝" 7. GD Knob 8. G Carriage Bolt, 5 16"-18 x 1 ¼" G Serrated Flange Nut, 5 16" GB Clutch Adapter Plate 10. G Hex Head Cap Screw, ⅜"-16 x 3 ½" G Washer, ⅜" USS G Lock Nut, ⅜" G Carriage Bolt, ¼"-20 x ⅝", Grade 2 G Serrated Flange Nut, ¼" GA Hopper Hold Down Latch 13. GA Hopper Support 14. GA Double Sprocket And Bearing, Drive Clutch, 11/19 Tooth 15. GD Spring 16. GD Shaft 17. GB Coupler 18. G Spring Pin, 3 16" x 1 ¼" A. GA Meter Drive Assembly Complete, 11/19 Tooth (Items 5-7 And 14-18) P18 Rev. 8/07

19 SEED HOPPER AND LID (RU87e/RU87a) (Per Row) 1. GD Lid 2. GA Seed Hopper, Reinforced 3. GD Seed Reserve Baffle P19 Rev. 8/07

20 FINGER PICKUP SEED METER RUA015/RUA056/RUA057(RU13k/RU13d) Left Rear View Of Complete Meter (Per Row) 1. G Spring Pin, ¼" x 1 ½" 2. G Spring Pin, 3 16" x 1 ½" 3. GD Housing Cover 4. GD Belt Drive Sprocket 5. GD Seed Belt 6. GA Bearing 7. GA Conveyor Housing 8. GB Bearing Housing 9. GR Carrier Plate W/Brush And Screw GA Brush G Rolling Thread Screw, No. 10 x ¾" 10. G Slotted Hex Washer Head Screw, No x ⅝" 11. GD Finger, Corn 12. GD Spring 13. GB Cam 14. GD Finger Holder 15. G Cotter Pin, 5 32" x 1" 16. G Locking Thumbscrew, 5 16"-18 x ¾" 17. GD Seed Baffle 18. GD Cover Nut 19. G Jam Nut, ⅝"-18 UNF 20. GA Wave Washer, ⅝" (Triple Wave) 21. G Hex Head Cap Screw, ¼"-20 x ⅝" G Hex Flange Nut, ¼"-20, No Serrations 22. G Hex Head Cap Screw, ¼"-20 x ½" G Serrated Flange Nut, ¼" G Hex Head Cap Screw, ¼"-20 x 1 ½" G Serrated Flange Nut, ¼" G Spring Pin, ¼" x 1 ¼" 25. GD Idler 26. GB Bushing, 17 64" I.D. x " Long 27. GD Finger, Oil Sunflower 28. GD Shank Cover, Finger Pickup Seed Meter 29. GD Half Rate Blank Finger A. GR Finger Assembly, Corn (Items And 20) B. GR Finger Assembly, Oil Sunflower (Items 12-14, 20 And 27) P20 Rev. 8/07

21 BRUSH-TYPE SEED METER RUA037/RUA056/RUA057(RU14f) Left Rear View Of Complete Meter Used W/Soybean And Cotton Discs Used W/ Milo/Grain Sorghum Discs 3 / 4 " 3 / 8 " (Per Row) 1. G Locking Thumbscrew, 5 16"-18 x ¾" 2. GA Housing W/Bearing GA Bearing 3. GA Hub W/Shoulder Bolts GD Shoulder Bolt, ¼"-20 (2 Used) 4. G Spring Pin, ¼" x 1 ¼" 5. G Spring Pin, ¼" x 1 ½" 6. GD Wear Strip 7. GA Upper Brush 8. GD Upper Brush Retainer (Used W/Soybean And Cotton Discs) 9. GA Lower Brush 10. GA Seed Disc, Soybean, 60 Cell, Black Color-Coded GA Seed Disc, Specialty Soybean, 48 Cell, Dark Blue Color-Coded GA Seed Disc, Cotton, Acid-Delinted, 30 Cell, White Color-Coded GA Seed Disc, Large Cotton, Acid-Delinted, 36 Cell, Tan Color-Coded GA Seed Disc, High-Rate Cotton, Acid-Delinted, 48 Cell, Light Green Color-Coded GA Seed Disc, Hill-Drop Cotton, Acid-Delinted, 12 Cell, Brown Color-Coded GA Seed Disc, Small Hill-Drop Cotton, Acid-Delinted, 12 Cell, Dark Green Color-Coded 11. G Wing Nut W/Nylon Insert, ¼" G Hex Washer Head Screw, No x ½" G Slotted Tap Screw, No x ⅝" (Use As Required) 13. GD Cover 14. GD Shank Cover, Brush-Type Seed Meter 15. GA Seed Disc, Small Milo/Grain Sorghum, 30 Cell, Red Color-Coded GA Seed Disc, Large Milo/Grain Sorghum, 30 Cell, Light Blue Color-Coded GA Seed Disc, High-Rate Small Milo/Grain Sorghum, 60 Cell, Red Color-Coded GA Seed Disc, High-Rate Large Milo/Grain Sorghum, 60 Cell, Yellow Color-Coded 16. GD Upper Brush Retainer (Used W/Milo/Grain Sorghum Discs) P21 Rev. 8/07

22 GRANULAR CHEMICAL HOPPER AND HOPPER PANEL EXTENSION (METR14d) P22 Rev. 8/07

23 GRANULAR CHEMICAL HOPPER AND HOPPER PANEL EXTENSION (Per Row) 1. G Washer, ⅜" USS 2. GD Sleeve, 9 16" Long 3. GD Spring 4. G Special Washer, ⅜" x 1 ½" O.D. 5. GD Sleeve, " Long 6. GD Idler 7. G Lock Nut, ⅜" G Hair Pin Clip, No GD1059L 1 Support, L.H. (Shown) GD1059R 1 Support, R.H. 10. G Hex Head Cap Screw, ⅜"-16 x ¾" G Lock Washer, ⅜" 11. G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" G Hex Head Cap Screw, ⅜"-16 x 2 ¾" 13. G External Retaining Ring, ⅝" 14. GD Plate 15. A Hopper Panel Extension (Non-Stock Item) (Sub Wholegoods Order Code ) 16. GD Block 17. G Hex Head Cap Screw, ¼"-20 x ¾" G Serrated Flange Nut, ¼" GD Hinge 19. GA Hopper 20. GA Lid 21. GD Knob 22. G Spring Pin, ¼" x 1 ½" P23 Rev. 8/07

24 GRANULAR CHEMICAL METER AND METER DRIVE RUA051/RUB028(RU91a) (Per Row) 1. G External Retaining Ring, ⅝" 2. GD Knob 3. G Spring Pin, ¼" x 1 ½" 4. - See Granular Chemical Hopper And Hopper Panel Extension, Pages P22 And P23 5. GA Sprocket And Bearing, Drive Clutch, 24 Tooth 6. GD Spring 7. GD Shaft 8. GB Coupler 9. G Spring Pin, 3 16" x 1 ¼" 10. GD Shaft 11. G Hex Socket Head Cap Screw, No x ⅞" G Lock Washer, No GD Feed Roller, Hex Bore 13. GB Bearing 14. GD Hex Bushing 15. G Chain, No. 41, 114 Pitch Including Connector Link GR Connector Link, No G Wave Washer, ½" 17. G Washer, ¼" USS 18. G Slotted Hex Self-Tapping Screw, ¼"-20 x ¾" 19. G Slotted Hex Self-Tapping Screw, No. 10 x ⅜" 20. GD Support Strap 21. GD Metering Gate 22. GB Granular Housing A. GA Granular Chemical Meter Complete (Items 1, 9, 10, And 16-22) P24 Rev. 8/07

25 GRANULAR CHEMICAL BANDING OPTIONS RUA061/RUA073(RU101m/RU83m) 1. GD Funnel 2. G Wire Hose Clamp, ¾" 3. GD Hose, 7 16" x 28" 4. G Slotted Pan Head Self-Tapping Screw, No. 10 x ½" 5. GA Slope-Compensating Bander W/Hardware (4 ½" Band Width) G Uni-Clamp G Pan Head Screw, No x 1 ¼" G Hex Nut, No GD U-Bolt, 1 ½" x " x ¼"-20 G Washer, ¼" USS G Lock Nut, ¼"-20, Grade B 7. GD Spacer 8. GD1115L - Hanger Bracket, L.H. 9. G Cotter Pin, ⅛" x ½" 10. GD1115R - Hanger Bracket, R.H. 11. G Carriage Bolt, ¼"-20 x 3 ¾", Grade 2 G Lock Washer, ¼" G Hex Nut, ¼" GD Hanger 13. GA Diffuser, 14" Band 14. G Carriage Bolt, ⅜"-16 x 2" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Clamp 16. G Carriage Bolt, ½"-13 x 2 ½" (Replaces Existing ½" x 2 ¼" Hardware) 17. GA Bracket (Straight Drop In-Furrow) 18. G1K385 - Bander Shield Kit W/Hardware And Instruction G Hex Head Cap Screw, ⅜"-16 x 1 ½" GD Special Washer, ⅜", Hardened P25 Rev. 8/07

26 SPRING TOOTH INCORPORATOR RUA055(RU95) (Per Row) 1. G Serrated Flange Nut, ¼" GD Eyebolt, ¼" G Twin Loop Chain, 9 Links 4. GD Front Bracket 5. G Carriage Bolt, ⅜"-16 x 1" G External Tooth Lock Washer, ⅜" G Serrated Flange Nut, ⅜" GD Spring Tooth 7. G Carriage Bolt, ⅜"-16 x ¾" G Serrated Flange Nut, ⅜" GD Rear Bracket 9. GA Cable Assembly P26 Rev. 8/07

27 ROW UNIT MOUNTED NO TILL COULTER (D14398/RU102c/RU152) STYLE A STYLE B (Per Row) 1. G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GA Arm (Style A) 3. G Hex Head Cap Screw, ⅝"-11 x 4" G Lock Nut, ⅝" G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GD Adapter 6. GA Hub W/Bearing And Retaining Ring GA Bearing, Double Row GD Retaining Ring, " 7. GD Disc Blade, Fluted, 1", 8 Flutes (Shown) GD Disc Blade, Bubbled, 1" GD Disc Blade, Fluted, ¾", 13 Flutes 8. GD Spacer 9. GA Arm (Style B) P27 Rev. 8/07

28 ROW UNIT MOUNTED BED LEVELER RUA059/RUA060(RU99/RU100) P28 Rev. 8/07

29 ROW UNIT MOUNTED BED LEVELER (Per Row) 1. G Detent Pin, ½" x 2 ½" Grip 2. G Square Head Set Screw, ⅝"-11 x 2 ¼" 3. G Hex Jam Nut, ⅝"-11, Grade 2 4. GA Mounting Bracket 5. GD Bushing, 1" O.D. x 9 16" I.D. x 7 16" Long 6. G Hex Head Cap Screw, ½"-13 x 1 ¾" GD Special Washer, ½", Hardened G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Nut, ½" GD Link 9. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Nut, ½" GA Anchor 11. G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Nut, ½" GA Leveler 13. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Nut, 5 16"-18, Grade GD Blade P29 Rev. 8/07

30 ROW UNIT MOUNTED DISC FURROWER RUA059/RUA058(RU99/RU98g) P30 Rev. 8/07

31 ROW UNIT MOUNTED DISC FURROWER (Per Row) 1. G Detent Pin, ½" x 2 ½" Grip 2. G Square Head Set Screw, ⅝"-11 x 2 ¼" 3. G Hex Jam Nut, ⅝"-11, Grade 2 4. GA Mounting Bracket 5. GD Bushing, 1" O.D. x 9 16" I.D. x 7 16" Long 6. G Hex Head Cap Screw, ½"-13 x 1 ¾" GD Special Washer, ½", Hardened G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Nut, ½" GD Link 9. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Nut, ½" GA Anchor 11. G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Nut, ½" GA Support Arm 13. G Truss Head Slotted Machine Screw, 5 16"-18 x ⅞" G Hex Nut, 5 16" GD Dust Cap 15. G Hex Head Cap Screw, ⅝"-11 x 4 ½" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Hub W/Bearings GA Bearing 17. GD Disc Blade, Solid, 12" (Shown) GD Disc Blade, Notched, 12" 18. GD Spacer, 11 16" I.D. x ¾" Long GD Spacer, 11 16" I.D. x ½" Long P31 Rev. 8/07

32 ROW UNIT MOUNTED RESIDUE WHEEL (RU103dd/RU103d) STYLE B STYLE A P32 Rev. 8/07

33 ROW UNIT MOUNTED RESIDUE WHEEL (Per Row) 1. GD Dust Cap 2. GD Wheel, 12 Tine, ⅜" x 12" 3. G Hex Head Cap Screw, ⅝"-11 x 2 ¼" 4. GD Backing Plate 5. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade 8 6. GD Spacer, ½" x " Long 7. GA Wheel Mount 8. G Hex Head Cap Screw, ½"-13 x 3 ½" G Lock Washer, ½" G Hex Nut, ½" GD Spring 10. G Hex Head Cap Screw, ½"-13 x 4 ½" G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 5" (Lockup Bolt) G Lock Nut, ½" GD Spacer, ½" x 3" Long 13. GA Lower Link 14. GA Mount 15. G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GA Upper Link 17. G Hex Head Cap Screw, ½"-13 x 3", Full Thread G Hex Jam Nut, ½"-13, Grade GA Hub W/Bearings GA Bearing 19. GD Cover 20. GB Wheel, 12 Tine, ⅜" x 12" A. GA Wheel Assembly, 12 Tine (Items 2, 4, 5 And 18) B. GA Wheel Assembly, 12 Tine, R.H. (Items 4, 5, 18 And 20) P33 Rev. 8/07

34 COULTER MOUNTED RESIDUE WHEELS (RU104uuu/RU153) STYLE A - Used With Style A Row Unit Mounted No Till Coulter STYLE B - Used With Style B Row Unit Mounted No Till Coulter P34 Rev. 8/07

35 COULTER MOUNTED RESIDUE WHEELS (Per Row) 1. GD Dust Cap 2. G Hex Head Cap Screw, ⅝"-11 x 3" G Hex Jam Nut, ⅝"-11, Grade 2 3. GD Wheel, 12 Tine, ⅜" x 12" 4. GA Hub W/Bearings GA Bearing 5. GA Cam 6. GD Spring 7. G Washer, ½" SAE 8. G Lock Nut W/Nylon Insert, ½" G Hex Head Cap Screw, ½"-13 x 9 ½", Grade 8 GD Special Washer, ½", Hardened G Lock Nut W/Nylon Insert, ½" GA Mount 11. GD Sleeve, 7 ½" 12. G Machine Bushing, ⅝" (.030" Thick) 13. GA Weed Guard W/Spring Pin G Spring Pin, ¼" x 1" 14. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade GD Backing Plate 16. GB Wheel, 12 Tine, ⅜" x 12" 17. GB Mount 18. G Hex Head Cap Screw, ¾"-10 x 10 ½" GB Bushing, 1 ⅛" O.D. x 25 32" I.D. x ¾" Long G Washer, ¾" SAE G Lock Nut, ¾" GA Locking Pin 20. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Lock Washer, ⅜" A. GA Wheel Assembly, 12 Tine, R.H. (Items 3, 4, 14 And 15) (Shown) GA Wheel Assembly, 12 Tine, L.H. (Items 3, 4, 14 And 15) B. GA Wheel Assembly, 12 Tine, R.H. (Items 4, 14, 15 And 16) (Shown) GA Wheel Assembly, 12 Tine, L.H. (Items 4, 14, 15 And 16) P35 Rev. 8/07

36 FRAME MOUNTED COULTER W/RESIDUE WHEELS (RU135c/RU135g/RU135hh) With Residue Wheels STYLE B STYLE A P36 Rev. 8/07

37 FRAME MOUNTED COULTER W/RESIDUE WHEELS (Per Row) 1. G Hex Head Cap Screw, ¾"-10 x 12" 2. GA Plate W/Angle 3. G Hex Head Cap Screw, ½"-13 x 1 ¾" 4. GA Coulter Frame 5. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 6 ½" G Lock Nut, ¾" GD Spring Anchor Bar 8. G Carriage Bolt, ½"-13 x 1 ¼" G Lock Nut, ½" GD Adapter 10. GA Hub W/Bearing And Retaining Ring GA Double Row Bearing GD Retaining Ring, " 11. GD Disc Blade, Fluted, 1", 8 Flutes (Shown) GD Disc Blade, Bubbled, 1" GD Disc Blade, Fluted, ¾", 13 Flutes 12. GB Spring Seat 13. GD Compression Spring 14. GD Sleeve 15. G Hex Head Cap Screw, ⅝"-11 x 5" G Lock Nut, ⅝" GA Coulter Arm W/Grease Fitting G Grease Fitting, 45, ¼" G Hex Head Cap Screw, ⅝"-11 x 5 ½" G Lock Nut, ⅝" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 19. GD Dust Cap 20. G Hex Head Cap Screw, ⅝"-11 x 3" G Hex Jam Nut, ⅝"-11, Grade GD Wheel, 12 Tine, ⅜" x 12" 22. GA Hub W/Bearings GA Bearing 23. GD Backing Plate 24. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade G Machine Bushing, ⅝" (.030" Thick) 26. GA Weed Guard W/Spring Pin G Spring Pin, ¼" x 1" 27. GA Mount 28. GA Cam 29. GD Spring 30. G Lock Nut W/Nylon Insert, ½" G Hex Head Cap Screw, ⅝"-11 x 1 ¾" G Lock Nut, ⅝" GA Support 33. G Hex Head Cap Screw, ½"-13 x 1" G Hex Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 5 ½" G Washer, ⅝" SAE G Lock Nut W/Nylon Insert, ⅝" GD Sleeve, 3" 36. GB Wheel, 12 Tine, ⅜" x 12" A. GA Wheel Assembly, 12 Tine, R.H. (Items 21-24) (Shown) GA Wheel Assembly, 12 Tine, L.H. (Items 21-24) B. GA Wheel Assembly, 12 Tine, R.H. (Items 22, 23, 24 And 36) (Shown) GA Wheel Assembly, 12 Tine, L.H. (Items 22, 23, 24 And 36) P37 Rev. 8/07

38 INTERPLANT PUSH ROW UNIT (RU156c/R141d) NOTE: Push row units use the same seed tube, row unit depth adjustment components, quick adjustable down force springs, 15" opener disc blades, gauge wheels, closing wheels, meter drive and seed hopper as the pull row unit. See those pages for common parts. P38 Rev. 8/07

39 INTERPLANT PUSH ROW UNIT (Per Row) 1. GD Sleeve, " Long 2. GD Spring 3. G Special Washer, ⅜" x 1 ½" O.D. 4. GD Sleeve, 1 ⅜" Long 5. GD Idler 6. G Washer, ⅜" USS 7. G Lock Nut, ⅜" G Chain, No. 41, 96 Pitch Including Connector Link GR Connector Link, No GA Push Row Unit Shank 10. GB Hopper Mount 11. G Hex Head Cap Screw, ⅝"-18 x 1 ¾" G Lock Nut, ⅝" G Carriage Bolt, ⅜"-16 x 1 ¼" G Hex Nut, ⅜"-16 G Lock Nut, ⅜" G Carriage Bolt, ⅜"-16 x 3 ½" 14. GD Stop 15. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Nut, ⅜" GB Seed Tube Guard/Inner Scraper 17. G Hex Socket Head Cap Screw, 5 16"-18 x 1", Grade G Hex Head Cap Screw, ⅝"-18 x 1 ¾" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 20. GA Upper Arm 21. GA Lower Arm 22. G Hex Head Cap Screw, ⅝"-18 x 2" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Bearing/Sprocket, ⅞" Hex Bore 24. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" GA Mounting Plate 26. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" G Spring Pin, 5 16" x 1 ⅛" 28. GD Lockup 29. G Cotter Pin, ¼" x 1 ½" 30. GD Spring 31. G Clevis Pin, ½" x 1 ½" G Cotter Pin, ⅛" x ¾" 32. GD Spring Tab 33. G Washer, ½" USS 34. GA Lift Lever W/Boot GD Boot 35. GD Bracket 36. GD Wire Lock Pin, ¼" x 1 ¾" 37. GD Mount 38. G Washer, ⅜" SAE 39. GA T-Bolt, ⅝"-11 x 6" G Lock Washer, ⅝" G Hex Nut, ⅝" GA Upper Arm 41. GA Mounting Plate P39 Rev. 8/07

40 OUTER HITCH/SAFETY CHAIN PHA038/PHA025(TWL1f/WGN47a/B0292) 1. GB Clevis, Single 2. GA Hitch Mount, 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" 3. G Hex Head Cap Screw, 1 ¼"-7 x 6" G Lock Nut, 1 ¼"-7 4. G Hex Head Cap Screw, ¾"-10 x 2 ¾" G Lock Washer, ¾" G Hex Nut, ¾" GD Pin, 1 ¼" x 5 ⅛" G Cotter Pin, 3 16" x 2" 6. G Hex Head Cap Screw, ⅝"-11 x 2 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GA Jack Assembly Complete GA Detent Pin Assembly GR Pin GR Crank Assembly GR Bevel Gear Set, Includes: (2) Bevel Gears, (1) Gear Pin, (1) Groove Pin 8. GA Hitch Mount, 8 Row 36"/38" And 12 Row 30", 12 Row 36"/38" ( Y Hitch Only) 9. GD Hose Holder 10. GA Detent Pin W/Chain (Transport Latch Locking Pin) 11. See Transport Latch Cylinder, Page P G Hex Head Cap Screw, ⅝"-11 x 2 ¼" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Catch Bar 14. GD Spring 15. GA Transport Latch 16. G Spring Pin, ¼" x 1" P40 Rev. 8/07

41 OUTER HITCH/SAFETY CHAIN 17. G Hex Head Cap Screw, ⅜"-16 x 3" GD Sleeve, 2" Long G Lock Nut, ⅜" G Washer, ½" USS G Lock Nut, ½" GD Pin, ¾" x 3 ⅜" G Cotter Pin, 5 32" x 1 ½" 20. GD Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 21. GD Hose Clamp, ⅝" x 1 ½" x 1 ½" 22. GD U-Bolt, 3" x 4" x ⅝"-11 G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" See Hose Take-Up, Pages P48 And P GA Roller W/Bronze Bushings, 8 Row Y And T Hitch, 12 Row Y Hitch GA Roller W/Bronze Bushings, 12 Row T Hitch And 16 Row Y and T Hitch GD Bronze Bushing 25. G Lock Nut, ⅜" G Lock Nut, ½" G Hex Head Cap Screw, ¾"-10 x 2" G Lock Nut, ¾" GA Bracket, Jack Mount GD Rubber Pad 29. GA Safety Pin, 12 ¾", 8 Row 36"/38" And 12 Row 30", 12 Row 36"/38" ( Y Hitch Only) GA Safety Pin, 14 ¾", 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" GD Lynch Pin, ¼" GD Lynch Pin, 7 16" 30. G Hex Head Cap Screw, ½"-13 x 1" G Lock Washer, ½" 31. G Hex Head Cap Screw, ½"-13 x 1 ½", 8/12 Row G Hex Head Cap Screw, ½"-13 x 2", 16 Row G Lock Washer, ½" G Hex Nut, ½" GA Wear Mount, 8 Row 36"/38" And 12 Row 30", 12 Row 36"/38" ( Y Hitch Only) GA Wear Mount, L.H., 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" GA Wear Mount, R.H., 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" GA Wear Pad Retainer, 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" 33. GD Shim, 4" x 4" (As Required), All Sizes GD Shim, 4" x 6" (As Required), 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" 34. GD Wear Pad, Nylatron, 4" x 4" (As Required), All Sizes GD Wear Pad, Nylatron, 4" x 6" (As Required), 12 Row 36"/38" ( T Hitch Only) And 16 Row 30" 35. GD Shim, 16 Gauge (16 Row Only) GD Shim, ⅜" (16 Row Only) 36. G Hex Head Cap Screw, ½"-13 x 1" G Lock Washer, ½" G Washer, ½" USS 37. A Outer Hitch, Y, 73", 8 Row 36"/38" (Non-Stock Item) A Outer Hitch, T, 97", 8 Row 36"/38" (Non-Stock Item) A Outer Hitch, Y, 97", 12 Row 30" (Non-Stock Item) A Outer Hitch, T, 121", 12 Row 30" (Non-Stock Item) A Outer Hitch, Y, 121", 12 Row 36"/38" (Non-Stock Item) A Outer Hitch, T, 151 ½", 12 Row 36"/38" (Non-Stock Item) A Outer Hitch, Y, 127 ½", 16 Row 30" (Non-Stock Item) A Outer Hitch, T, 151 ½", 16 Row 30" (Non-Stock Item) 38. GD Pin, 1 ¼" x 12", 8 Row Y And T Hitch, 12 Row Y Hitch GD Pin, 1 ¼" x 14", 12 Row T Hitch And 16 Row Y and T Hitch G Spring Pin, ⅜" x 2" 39. GA Safety Chain, ½" G1K412 - Safety Chain Repair Kit, Includes Hook, Flat Washer, Latch Pin, Safety Latch, Spring And Retaining Ring 40. G Hex Head Cap Screw, 1 ¼"-7 x 3" GD Special Washer G Washer, 1 ¼" SAE G Lock Nut, 1 ¼" GB Hitch Clevis, Single P41 Rev. 8/07

42 2-POINT HITCH OPTION (A12406) P42 Rev. 8/07

43 2-POINT HITCH OPTION 1. GA Hammer Strap, Category 3N And 3 2. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" 3. GA Hitch Bar 4. GA Pivot Mount 5. GA Pivot Bolt W/Grease Fitting, 1 ¾" x 10 ⅜" (Total Length) G Grease Fitting, ¼"-28 GD Washer, 3" O.D. x " x ¼" Thick GD Sleeve, 3" O.D. x " x Thick 6. G Hex Head Cap Screw, ⅝"-11 x 1 ¼" G Washer, ⅝" USS 7. GD Pivot Lock 8. GA Pin, 13 ⅜" 9. GA Hitch Pivot W/Bushings And Grease Fittings GD Hardened Bushing, 2 ¾" O.D. x 2 ¼" I.D. x 3 G Grease Fitting, 90, ¼" G Hex Head Cap Screw, 1"-8 x 2" G Lock Washer, 1" GD Washer, 4" O.D. x " I.D. x ⅜" 11. G Hex Head Cap Screw, 1 ¼"-7 x 6" G Lock Nut, 1 ¼" GD Washer, 4" O.D. x 2 ¼" I.D. x ¼" P43 Rev. 8/07

44 INNER HITCH, Y PHA035/PHA037(TWL2i) P44 Rev. 8/07

45 INNER HITCH, Y 1. G Hex Head Cap Screw, ½"-13 x 1", 8 Row 36"/38" And 12 Row 30"/36"/38" G Hex Head Cap Screw, ½"-13 x 1 ½", 16 Row 30" G Lock Washer, ½", 16 Row 30" 2. GD Wear Pad, Nylatron, 4" x 4" GD Shim, 4" x 4" 3. G External Washer 4. GD Shaft, 1 ¼" x 6 ⅜", 8 Row 36"/38" And 12 Row 30"/36"/38" GD Shaft, 1 ¼" x 7 ⅜", 16 Row 30" 5. GA Tongue Hook W/Grease Fittings, 8/12 Row GA Tongue Hook W/Grease Fittings,16 Row G Grease Fitting, ⅛" NPT 6. GD Pin, 1 ¼" x 12", 8/12 Row GD Pin, 1 ¼" x 14 ½", 16 Row G Cotter Pin, ⅜" x 2" 7. GD Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 8. See Hose Take-Up, Pages P48 And P49 9. G Hex Head Cap Screw, ½"-13 x 3 ½" G Lock Nut, ½" G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Hose Clamp 12. G Hex Head Cap Screw, ⅜"-16 x 1 ½" G Washer, ⅜" USS G Lock Nut, ⅜" GD Shield (If Applicable) 14. GD Pin, 1 ¼" x 5 ⅛" G Cotter Pin, 3 16" x 2" 15. G Square Head Set Screw, 5 16"-18 x ¾" 16. GB Shoe 17. GD Shaft, 1 ¼" x 7", 8/12 Row GD Shaft, 1 ¼" x 8", 16 Row 18. A Inner Hitch, 145 ⅜", 8 Row 36"/38" (Non-Stock Item) A Inner Hitch, 169 ⅜", 12 Row 30" (Shown) (Non-Stock Item) A Inner Hitch, 191 ⅝", 12 Row 36"/38" (Non-Stock Item) A7426 Inner Hitch, 205 ⅜", 16 Row 30" (Non-Stock Item) See Tongue Cylinder, Pages P83-P See Tongue Lock Cylinder, Page P GD U-Bolt, 2 ⅛" x 1 ⅞" x ⅜"-16 G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Sleeve 24. GD Shim, 2 ½" x 10", 7 Gauge GD Shim, 2 ½" x 10", 10 Gauge GD Shim, 2 ½" x 10", 12 Gauge GD Shim, 2 ½" x 10", 14 Gauge P45 Rev. 8/07

46 INNER HITCH, T PHA035/PHA036(TWL3f) P46 Rev. 8/07

47 INNER HITCH, T 1. G Hex Head Cap Screw, ½"-13 x 1", 8 Row 36"/38" And 12 Row 30" G Hex Head Cap Screw, ½"-13 x 1 ½", 12 Row 36"/38" And 16 Row 30" G Lock Washer, ½", 12 Row 36"/38" And 16 Row 30" 2. GD Wear Pad, Nylatron, 4" x 4" GD Shim, 4" x 4" 3. G External Washer 4. GD Shaft, 1 ¼" x 6 ⅜", 8 Row 36"/38" And 12 Row 30" GD Shaft, 1 ¼" x 7 ⅜", 12 Row 36"/38" And 16 Row 30" 5. GA Tongue Hook W/Grease Fittings, 8 Row 36"/38" And 12 Row 30" GA Tongue Hook W/Grease Fittings,12 Row 36"/38" And 16 Row 30" G Grease Fitting, ⅛" NPT 6. GD Pin, 1 ¼" x 12", 8 Row 36"/38" And 12 Row 30" GD Pin, 1 ¼" x 14 ½", 12 Row 36"/38" And 16 Row 30" G Cotter Pin, ⅜" x 2" 7. - See Hose Take-Up, Pages P48 And P49 8. GD Pin, 1 ¼" x 5 ⅛" G Cotter Pin, 3 16" x 2" 9. G Square Head Set Screw, 5 16"-18 x ¾" 10. GB Shoe 11. GD Shaft, 1 ¼" x 7", 8 Row 36"/38" And 12 Row 30" GD Shaft, 1 ¼" x 8", 12 Row 36"/38" And 16 Row 30" 12. A Inner Hitch, 121 ⅝", 8 Row 36"/38" (Non-Stock Item) A Inner Hitch, 145 ⅜", 12 Row 30" (Shown) (Non-Stock Item) A Inner Hitch, 183 ⅛", 12 Row 36"/38" And 16 Row 30" (Non-Stock Item) See Tongue Cylinder, Pages P83-P See Tongue Lock Cylinder, Page P GD U-Bolt, 2 ⅛" x 1 ⅞" x ⅜"-16 G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 3 ¼" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Sleeve 18. GD Shim, 2 ½" x 10", 7 Gauge GD Shim, 2 ½" x 10", 10 Gauge GD Shim, 2 ½" x 10", 12 Gauge GD Shim, 2 ½" x 10", 14 Gauge P47 Rev. 8/07

48 HOSE TAKE-UP PHA039(TWL137/TWL171) STYLE B STYLE A P48 Rev. 8/07

49 HOSE TAKE-UP 1. G Carriage Bolt, ⅝"-11 x 2" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Take-Up, 28 ¼", 8 Row 36"/38" Y Hitch GA Take-Up, 44 ¼", 8 Row 36"/38" T Hitch And 12 Row 30" Y Hitch (Shown) GA Take-Up, 56 ¼", 12 Row 30" T Hitch, 12 Row 36"/38" And 16 Row 30" Y Hitch GA Take-Up, 67 ⅝", 12 Row 36"/38" And 16 Row 30" T Hitch 3. GD Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 4. G Hex Head Cap Screw, ½"-13 x 2 ¼" G Hex Head Cap Screw, ½"-13 x 2 ½" G Lock Nut, ½" G Hex Head Cap Screw, ½"-13 x 2 ¼" G Lock Nut, ½" GA Take-Up, 28 ¼", 8 Row 36"/38" Y Hitch GA Take-Up, 44 ¼", 8 Row 36"/38" T Hitch And 12 Row 30" Y Hitch (Shown) GA Take-Up, 56 ¼", 12 Row 30" T Hitch And 12 Row 36"/38" And 16 Row 30" Y Hitch GA Take-Up, 67 ⅝", 12 Row 36"/38" And 16 Row 30" T Hitch 7. GD Cover, 8 Row 36"/38" T Hitch, 12 Row 30"/36"/38" Y / T Hitch And 16 Row 30" Y / T Hitch (Shown) GD Cover, 8 Row 36"/38" Y Hitch 8. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Washer, ⅜" SAE G Hex Nut, ⅜" G Hex Head Cap Screw, ⅜"-16 x 5" G Washer, ⅜" USS G Lock Nut, ⅜" See Valve Block - Located On Hitch, Pages P90 And P GA Mount (If Applicable) See Relief Valve - Located On Hitch, Page P G Carriage Bolt, 5 16"-18 x 2 ½" G Lock Washer, 5 16" G Hex Nut, 5 16"-18 P49 Rev. 8/07

50 CENTER FRAME PFA070/VVB034(TWL138a) 12 ROW 30" SHOWN P50 Rev. 8/07

51 CENTER FRAME 1. G Hex Nut, ½"-13 G Hex Socket Set Screw, ½"-13 x 1 ¼" 2. G Machine Bushing, 3 ⅛" x 2 ⅛" x 3 16" (As Required) G Machine Bushing, 2 ⅛", 10 Gauge (As Required) G Machine Bushing, 2 ⅛", 14 Gauge (As Required) 3. GD Hinge Pin, 2 ⅛" x 25 ¾" 4. GD Adjustment Block 5. G Hex Head Cap Screw, ¾"-10 x 3 ¾" G Washer, ¾" USS G Lock Nut, ¾" GA Safety Hook 7. GD Pin, 1 ¼" x " 8. G Washer, ⅝" SAE G Lock Nut, ⅝" GD Spring 10. GD Pin, 1 ¼" x 6" 11. GA Spring Rod 12. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Washer, ½" SAE G Lock Washer, ½" GD Sleeve, ½" x ½" Long 13. GA Pad Holder W/Bars GD Bar, 1 ¼" x 6" x ¼" Thick GD Bar, 1 ¼" x 6" (⅜" Thick) G Hex Head Cap Screw, ⅜"-16 x 1" 14. GD Wear Pad, 7" x 7", ½" Thick 15. GD Special Washer, ⅝", Hardened G Hex Nut, ⅝" GD Cap 17. GD Clamp, ⅞" x 3" x 5 ⅜" GD Rubber Pad 18. G Hex Head Cap Screw, ½"-13 x 2 ½" G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ¾"-10 x 3", Full Thread G Hex Nut, ¾" See Valve Blocks - Located On Rear Center Frame, Page P A Frame W/Cam Follower Mounts, 166", 8 Row 36"/38" And 12 Row 36"/38" (Non-Stock Item) A Frame W/Cam Follower Mounts, 136", 12 Row 30" And 16 Row 30" (Non-Stock Item) GA Cam Follower Mount, L.H. GA Cam Follower Mount, R.H. 22. G Hex Head Cap Screw, ¾"-10 x 1 ½" 23. GB Spring Washer 24. GD Sleeve 25. GA Cam Follower W/Grease Fitting G Grease Fitting, ¼"-28 P51 Rev. 8/07

52 WING FRAME (TWL180a/TWL139g) WITH INTERPLANT PACKAGE OPTIONS NOTE: Installed On Even-Row Push Row Unit 1. GA Light Bracket (Wide Row Sizes Only) 2. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" G Hex Head Cap Screw, ⅜"-16 x 1" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Light Bracket (Wide Row Sizes Only) 5. G Hex Head Cap Screw, ¼"-20 x 1" G Lock Nut, ¼"-20, Grade B 6. - See Electrical Components, Pages P100 And P101 P52 Rev. 8/07

53 WING FRAME 7. GD Hose Clamp, 9 16" x 2 ½" x 2" 8. G Lock Nut, ⅜" GD Pin, 1 ¼" x 9" G Cotter Pin, ¼" x 2" 10. A Wing, R.H., 75 ½", 8 Row 36"/38" (Non-Stock Item) A Wing, L.H., 75 ½", 8 Row 36"/38" (Non-Stock Item) A Wing, R.H., 119 ¼", 12 Row 30" (Non-Stock Item) A Wing, L.H., 119 ¼", 12 Row 30" (Non-Stock Item) A Wing, R.H., 152", 12 Row 36"/38" (Non-Stock Item) A Wing, L.H., 152", 12 Row 36"/38" (Non-Stock Item) A Wing, R.H., 179 ¼", 16 Row 30" (Two Wheel Towers Per Wing) (Non-Stock Item) A Wing, L.H., 179 ¼", 16 Row 30" (Two Wheel Towers Per Wing) (Non-Stock Item) 11. GA Link 12. GD Strap, 56", 8 Row 36"/38" And 12 Row 36"/38" GD Strap, 41", 12 Row 30" And 16 Row 30" 13. GD Pin, 1 ¼" x 10 ½" G Machine Bushing, 1 ¼", 10 Gauge G Cotter Pin, ¼" x 2" 14. GA Toggle Link 15. GD Pin, 1 ¼" x 7" G Machine Bushing, 1 ¼", 10 Gauge G Cotter Pin, ¼" x 2" See Wing Lock Cylinder, Page P GD Pin 1 ¼" x 7" G Spring Pin, ¼" x 2" 18. GD Bracket 19. GD Pin, 1 ¼" x 5" G Cotter Pin, ¼" x 2" 20. G Detent Pin, ½" x 3 ½" Grip 21. GD Push Row Unit Light Bracket 22. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 3 ½" G Washer, ½" SAE G Lock Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 7" G Lock Washer, ⅝" G Hex Nut, ⅝" GD Mounting Bracket 26. G Carriage Bolt, 5 16"-18 x ¾" G Serrated Flange Nut, 5 16" GD Light Mount Extension 28. G Hex Head Cap Screw, ¼"-20 x 1" G Lock Washer, ¼" G Hex Nut, ¼" GA Light Bracket 30. GB Light Mount Bracket A. G7698X - Push Row Unit Mounted Light Bracket Package (Items 21 And 22 On This Page And 42" Harness Extension, Item 5 On Pages P90 And P91) P53 Rev. 8/07

54 CENTER PIVOT PFA067/PFA068(TWL7c) P54 Rev. 8/07

55 CENTER PIVOT 1. - See Center Lift Cylinder, Page P80 2. GA Hook Strap 3. GD Sleeve, 3 ⅝" GD Sleeve, " 4. G Hex Head Cap Screw, ⅝"-11 x 5 ½" G Lock Nut, ⅝" G Carriage Bolt, ⅝"-11 x 2" G Lock Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 2 ½" GD Special Washer, 25 32" I.D. x 1 ¼" O.D., Hardened 7. GA Pin, 2 ⅛" 8. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GR Pin, 1" x 3 ½" GR Hair Pin Clip 10. GA Center Post 11. G Hex Head Cap Screw, ⅞"-9 x 3", Grade 8 GD Hardened Washer, ⅞" G Hex Nut, ⅞"-9, Grade GA Cone 13. GA Bearing Housing W/Cups, Less Grease Fitting GD Cup G Grease Fitting, 90, ¼" GD Shim,.005" Thick (As Required) GD Shim,.020" Thick (As Required) GD Shim,.007" Thick (As Required) 15. GD O-Ring 16. GD Bearing Cap P55 Rev. 8/07

56 AXLE ASSEMBLY HTA043/HTA044/PFA071/PHA033/PHA034/PFA073(TWL140cc) P56 Rev. 8/07

57 AXLE ASSEMBLY 1. GD Lynch Pin, ¼" 2. G Hex Head Cap Screw, ¾"-10 x 2 ¾" G Hex Head Cap Screw, ¾"-10 x 3" G Lock Washer, ¾" G Hex Nut, ¾" GA Manual Safety Lockup W/Detent Pin GA Detent Pin W/Chain 4. GA Bulkhead Mount 5. GD Pin G Lock Washer, 7 16" G Hex Nut, 7 16" GA Cable, 8 Row 36"/38" And 12 Row 36"/38" GA Cable Assembly, 12 Row 30" And 16 Row 30" 7. G Lock Washer, ½" G Hex Nut, ½" G Lock Nut, ¾"-16 G Lock Nut, ⅞" GD Pin, 1 ¼" x 5 1 / 4 " G Washer, 1 ¼" SAE G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Lock Nut, ⅜" See Rotation Cylinder, Page P G Hex Head Cap Screw, ¾"-8 x 2 ½", Grade 8, Y Hitch G Hex Head Cap Screw, ¾"-10 x 3 ½", Grade 8, T Hitch GD Special Washer, 25 32" I.D. x 1 ¼" O.D., Hardened G Hex Nut, ¾" GD Pin, 1 ¼" x 5 ¼", All Sizes G Cotter Pin, ¼" x 2" 13. GA Axle W/Stub Axle, 12 Row 30" And 16 Row 30" GA Stub Axle, Narrow Row GA Axle W/Stub Axle, 8 Row 36"/38" And 12 Row 36"/38" GA Stub Axle, Wide Row 14. GD Scraper 15. G Carriage Bolt, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, 1"-8 x 10", Grade 8, Y Hitch G Hex Head Cap Screw, 1"-8 x 11", Grade 8, T Hitch GD Special Washer, " I.D. x 2" O.D. G Hex Nut, 1"-8, Grade G Carriage Bolt, ½"-13 x 1 ½" G Lock Washer, ½" G Hex Nut, ½"-13 P57 Rev. 8/07

58 TRANSPORT WHEELS/ROCK GUARDS HTA032/HTA040/HTA043/HTA004(TWL141c) P58 Rev. 8/07

59 TRANSPORT WHEELS/ROCK GUARDS (Per Assy.) 1. G Hex Head Cap Screw, ⅞"-9 x 2 ½", Grade 8 G Lock Washer, ⅞" 2. GA Spindle W/Retaining Ring, 1 ¾" G External Retaining Ring, 2 ½" 3. GA Seal 4. GA Bearing 5. GA Hub W/Cups, Bolts, Nuts And Grease Fitting, 8 Bolt, 1 ¾" Bore G Grease Fitting, ¼"-28 GD Cup GR Lug Bolt, ⅝"-12 x 2 ¼", Grade 8 GR Lug Nut, ⅝"-18 UNF 6. GD Special Nut, 1 ¾"-12 UNF 7. GD Special Hex Nut, 1 ¾"-12 UNF 8. GA Rim, 5.5" x 22.5", All Sizes 9. GD Tire, R 22.5" W/O Center Rib, Tubeless (Specify Brand*) 10. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Lock Washer, ½" G Hex Nut, ½" GA Rock Guard (Optional) 12. GA Valve Stem A. GA Tire And Rim Assembly (Items 8, 9 And 12) (Specify Brand*) * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. P59 Rev. 8/07

60 CONTACT DRIVE WHEEL AND DRIVE SHAFT(S) (PLTR155/TWL11e/TWL11k/PLTR150/TWL11f) 16 Row 8/12 Row P60 Rev. 8/07

61 CONTACT DRIVE WHEEL AND DRIVE SHAFT(S) (TWL157/TWL156) See Pages P56 And P57 See Pages P56 And P57 B B 8/12 Row (L.H. Side) 16 Row (L.H. Side) (Per Assy.) 1. GD SMV Sign 2. G Hex Head Cap Screw, ¼"-20 x ½" G Lock Washer, ¼" G Hex Nut, ¼" GD Bracket 4. GD Cover 5. GD Spring 6. - See Hydraulic Hoses And Fittings On Planter Frame, Pages P98 And P See Inner Module Drive, Page P67 8. GD Hex Shaft, ⅞" x 13", See Point Row Clutch, Pages P68-P71 For 8 And 12 Row Machines Equipped With Point Row Clutches 9. G Spring Pin, ¼" x 1 ½" 10. G Hex Head Cap Screw, ⅜"-16 x 10" (Used To Secure Point Row Clutch) G Lock Nut, ⅜" GA Sprocket, 30 Tooth 12. G Machine Bushing, 1", 10 Gauge G Machine Bushing, 1", 14 Gauge 13. G Hex Head Cap Screw, ⅝"-11 x 4" G Hex Nut, ⅝"-11 G Lock Nut, ⅝" G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GA Pin, 2 ⅛" 16. G Clevis Pin, ⅜" x 1" G Retaining Ring, ⅜" See Wing Lift Cylinder, Page P GA Spring W/Plug 19. GD Lynch Pin, ¼" 20. GA Sprocket, 30 Tooth GA Sprocket, 15 Tooth, Half Rate (2 To 1) Drive (Continued On Following Page) P61 Rev. 8/07

62 CONTACT DRIVE WHEEL AND DRIVE SHAFT(S) (Per Assy.) (Continued) 21. GD Hex Shaft, ⅞" x 11 ¾" (2 Holes) 22. GA Flanged Bearing, ⅞" Hex Bore 23. G Carriage Bolt, 5 16"-18 x 1" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Idler W/Sprocket And Hardware, L.H. Side Of Planter GA Idler W/Sprocket And Hardware, R.H. Side Of Planter GA Sprocket W/Bearing, 19 Tooth G Hex Head Cap Screw, ½"-13 x 1 ½" G Machine Bushing, ½", 14 Gauge G Hex Jam Nut, ½"-13, Grade G Hex Head Adjusting Bolt, ½"-13 x 4", Grade 2 G Hex Jam Nut, ½"-13, Grade GD Tire, 4.80" x 8", 4 Ply, Rib Implement (Specify Brand*) GD Valve Stem 27. GA Rim, 3.75" x 8" 28. G Machine Bushing, 1", 10 Gauge 29. GA Wheel Arm 30. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 31. GD Shield 32. G Hex Head Cap Screw, ⅝"-11 x 1 ¾" G Machine Bushing, ⅞", 14 Gauge GD Special Washer, ⅝", Hardened G Washer, ⅝" SAE G Lock Nut, ⅝" GD Hinge, Female GD Hinge W/Pins, Male 34. G Hex Head Cap Screw, ¼"-20 x 1" G Washer, ¼" USS G Lock Washer, ¼" G Hex Nut, ¼" GD Hex Shaft, ⅞" x 29 ⅝" 36. G Cotter Pin, 3 16" x 1" 37. GD Spring 38. GA Block And Hub Assembly 39. GD L-Pin 40. GA Sprocket, 30 Tooth 41. G External Retaining Ring, 1 ¼" 42. G Chain, No. 40, 110 Pitch Including Connector Link, Half Rate (2 To 1) Drive G Chain, No. 40, 118 Pitch Including Connector Link GR Connector Link, No GD Coupler, 1 ¾", 16 Row Only See Point Row Clutch, Pages P68-P71 A. GA Tire And Rim Assembly (Items 26 And 27) (Specify Brand*) B. GA Ratchet/Sprocket Assembly, L.H. Side Of Planter (Items 36-41) GA Ratchet/Sprocket Assembly, R.H. Side Of Planter (Items 36-41) C. G1K324 - Contact Wheel Arm Replacement Kit (Items 9, 21-23, 25, 28 And 29) * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any change in contact tires. P62 Rev. 8/07

63 GROUND DRIVE WHEEL PTD057(TWL142c) (Per Assy.) 1. GD Pin, 1 ¼" x 13 ¼" 2. GA Wheel Module 3. G Spring Pin, ⅜" x 2" 4. GD Pin, 1 ¼" x 5 ⅝" G Washer, 1 ¼" SAE G Cotter Pin, ¼" x 2" 5. G Hex Head Cap Screw, ¾"-10 x 2" G Lock Washer, ¾" 6. G Hex Head Cap Screw, ¾"-10 x 2" G Lock Washer, ¾" G Hex Nut, ¾" GD Scraper Arm 8. GA Spindle W/Round External Retaining Ring, 10" GD Round External Retaining Ring 9. GA Bearing 10. GR Lug Bolt, 9 16" GA Hub W/Cups, 6 Bolt GR Cup 12. G Hex Jam Nut, 1 ½"-12, Grade GD Tire, 7.50" x 20", 8 Ply, Tubeless W/O Center Rib (Specify Brand*) 14. GA Valve Stem 15. GA Rim, 5.5" x 20" 16. GD Bar Clamp 17. G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Washer, ½" G Hex Nut, ½" G Carriage Bolt, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Scraper A. GA Tire And Rim Assembly (Specify Brand*)(Items 13-15) B. GA Hub And Spindle Assembly (Items 8, 9, 11 And 12) * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. P63 Rev. 8/07

64 SEED RATE TRANSMISSION AND ROW UNIT DRILL SHAFTS (TWL14n) 8/12 Row Shown (Per Side) 1. GD Shaft, ⅞" x 15" 2. GD Lynch Pin, ¼" 3. GA Sprocket, 17 Tooth GA Sprocket, 19 Tooth GA Sprocket, 23 Tooth GA Sprocket, 24 Tooth GA Sprocket, 25 Tooth GA Sprocket, 26 Tooth GA Sprocket, 27 Tooth GA Sprocket, 28 Tooth 4. G Spring Pin, ¼" x 1 ½" 5. G Clevis Pin, ⅜" x 1" G Retaining Ring, ⅜" 6. G Hex Head Cap Screw, ½"-13 x 2 ¼" GD Sleeve, 1" O.D. x 9 16" I.D. x ⅞" G Lock Washer, ½", Internal/External G Lock Nut, ½" GD Spring 8. GA Sprocket Storage Rod 9. GB Coupler See Inner Module Drive, Page P GD Coupler, 1 ¾", 16 Row Only 12. GD Hex Shaft, ⅞" x 31 ⅜", 16 Row Only 13. G Square Head Set Screw, 5 16"-18 x ¾" 14. G Square Head Set Screw, ⅜"-16 x ⅝" 15. GD Shear Coupler 16. G Cotter Pin, 3 16" x 2" 17. G Chain, No. 40, 80 Pitch Including Connector Link GR Connector Link, No GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth G Hex Head Cap Screw, ⅜"-16 x 1 ¾" GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" P64 Rev. 8/07

65 SEED RATE TRANSMISSION AND ROW UNIT DRILL SHAFTS (Per Side) 19. GD Shaft, ⅞" x 13 ½" 20. G Carriage Bolt, 5 16"-18 x 1" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Special Bearing 22. G Flangette 23. G Bearing, ⅞" Hex Bore, Spherical 24. GA Sprocket, 19 Tooth, Interplant Package Drive 25. GD Lock Clamp 26. GD Hex Shaft, ⅞" x 58 ½" (No Holes), Wing, 8 Row 36"/38" GD Hex Shaft, ⅞" x 106 ½" (No Holes), Wing, 12 Row 30" GD Hex Shaft, ⅞" x 134 ½" (No Holes), Wing, 12 Row 36"/38" GD Hex Shaft, ⅞" x 166 ¾" (No Holes), Wing, 16 Row 30" 27. GA Hanger Bearing, ⅞" Hex Bore 28. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 29. G Machine Bushing, 1", 10 Gauge 30. GA U-Joint W/Grease Fitting, Female, 18 ⅛" Long, 8 Row 36"/38" And 12 Row 36"/38" GA U-Joint W/Grease Fitting, Female, 10 ¼" Long, 12 Row 30" And 16 Row 30" GR Grease Fitting, 45, Metric GR Inboard Yoke And Outer Profile (18 ¼" U-Joint) GR Inboard Yoke And Outer Profile (10 ¼" U-Joint) GR Cross And Bearing Kit GR Yoke, ⅞" Hex 31. GA U-Joint W/Grease Fitting, Male, 12 ¼ " Long GR Grease Fitting, 45, Metric GR Inner Profile GR Inboard Yoke GR Spring Pin, 8mm x 50mm GR Cross And Bearing Kit GR Yoke, ⅞" Hex 32. GD Hex Shaft, ⅞" x 53" (No Holes), R.H. Main Frame, 8 Row 36"/38" And 12 Row 36"/38" GD Hex Shaft, ⅞" x 44" (No Holes), L.H. Main Frame, 8 Row 36"/38" And 12 Row 36"/38" GD Hex Shaft, ⅞" x 45" (No Holes), R.H. Main Frame, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 35" (No Holes), L.H. Main Frame, 12 Row 30" And 16 Row 30" 33. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Tightener Shaft, 3 ⅜" 35. GD Handle 36. G Vinyl Cap 37. G Hex Socket Button Head Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 38. G Machine Bushing, ⅞", 14 Gauge 39. G External Inverted Snap Ring, 1 ½" 40. G Internal Inverted Snap Ring, ⅞" 41. GD Sleeve, 1 ¼" 42. GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench)(Shown) GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) 43. GD Release Collar, Silver, L.H. (Shown) GD Release Collar, Gold, R.H. A. G1K269 - Lock Clamp Kit (Items 25 And 28) B. G1K381 - Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 34-43) (Shown) G1K380 1 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 34-43) P65 Rev. 8/07

66 BOLT-ON WHEEL MODULE/TRANSPORT LATCH CATCH PFA072(TWL15a) 8 Row 36"/38" 12 Row 36"/38" (Per Side) 1. GD U-Bolt, 5" x 7" x ¾"-10 G Lock Washer, ¾" G Hex Nut, ¾" GA Wheel Tower W/Grease Fitting, L.H. GA Wheel Tower W/Grease Fitting, R.H. G Grease Fitting, ¼" GA Transport Latch Catch 4. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" P66 Rev. 8/07

67 INNER MODULE DRIVE PTD058/PFA046/PTD077(TWL16e) 16 Row (Per Module) 1. - See Seed Rate Transmission And Row Unit Drill Shafts, Pages P64 And P See Contact Drive Wheel And Drive Shaft(s), Pages P60-P62 3. G Hex Head Cap Screw, ⅝"-11 x 3 ¾" G Machine Bushing, ⅝", 14 Gauge (As Required) G Hex Nut, ⅝"-11 G Lock Nut, ⅝" GA Idler W/Sprocket And Hardware, L.H. Side Of Planter GA Idler W/Sprocket And Hardware, R.H. Side Of Planter GA Sprocket W/Bearing, 18 Tooth G Hex Head Cap Screw, ½"-13 x 3" GD Spacer, 1 ⅛" G Washer, ½" SAE G Lock Nut, ½" GD Spring 6. GA Sprocket, 50 Tooth 7. G Hex Head Cap Screw, ½"-13 x 2 ¼" GD Bushing, 1" O.D. x 9 16" I.D. x 7 16" Long G Machine Bushing, ½", 7 Gauge G Washer, ⅝" SAE G Lock Nut, ½" GA Sprocket W/Bearing, 18 Tooth 9. GA Sprocket, 28 Tooth 10. G Spring Pin, ¼" x 1 ½" 11. G Chain, No. 40, 100 Pitch Including Connector Link GR Connector Link, No G Clevis Pin, ⅜" x 1" G Retaining Ring, ⅜" P67 Rev. 8/07

68 POINT ROW CLUTCH PRC019(TWL70d/TWL71d/TWL71/TWL18/ L.H. Point Row Clutch Shown (Used On L.H. Side Of Planter) Input Shaft Connects To Clutch Solenoid Connects To Planter Harness At Valve Block On Rear Center Frame On Point Row Clutch P68 Rev. 8/07

69 POINT ROW CLUTCH (Per Assy.) 1. GD Input Shaft, R.H. Threads (Shown) GD Input Shaft, L.H. Threads 2. G Hex Socket Head Screw, ¼"-20 x 1" G Lock Washer, ¼" 3. G External Inverted Snap Ring, 1 ½" 4. GD V-Ring Seal 5. GD Input Hub 6. GA Hub/Sleeve Assembly W/Spring Pins G Spring Pin, ¼" x 1" G Spring Pin, 5 32" x ⅞" 7. G Hex Head Cap Screw, ¼"-20 x ¾" G Lock Washer, ¼" G Hex Nut, ¼" GA Solenoid Complete GR Snap Ring GR Spring GR Boot GR Plunger 9. G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Hex Nut, ⅜"-16 G Washer, ⅜" SAE G Lock Washer, ⅜" G Hex Jam Nut, ⅜"-16, Grade G Hex Socket Head Cap Screw, ¼"-20 x 1 ¾", Grade 8 G Lock Washer, ¼" G Hex Nut, ¼" GD Spring 12. GD Mounting Plate 13. GD Bushing 14. GD Coupler W/R.H. Threads (Shown) GD Coupler W/L.H. Threads 15. GD Felt Washer 16. GD Spring, L.H. (Shown) GD Spring, R.H. 17. GD Stop Collar 18. GD Rue Ring Cotter, 5 16" 19. GD Actuator Arm 20. G Spring Pin, 3 16" x 2 ¼" 21. G Hex Socket Head Screw, No x ½" G Lock Washer, No GD Hex Shaft, ⅞" x 13" 23. GA Wiring Harness, 192", R.H. Side, 8 Row 36"/38" GA Wiring Harness, 228", L.H. Side, 8 Row 36"/38" And R.H. Side, 12 Row 30" GA Wiring Harness, 264", L.H. Side, 12 Row 30" And R.H. Side, 12 Row 36"/38" GA Wiring Harness, 312", L.H. Side, 12 Row 36"/38" GA Wiring Harness, 252", R.H. Side, 16 Row 30" GA Wiring Harness, 300", L.H. Side, 16 Row 30" 24. GA Ground Cable, Green 25. G Fork Terminal 26. GD Lock Wire, 10", Stainless Steel 27. G Spring Pin, 3 16" x 1 ¼" A. GA Point Row Clutch Assembly, R.H. (R.H. Side Of Machine) (Items 1-21, 24, 26 And 27) GA Point Row Clutch Assembly, L.H. (L.H. Side Of Machine) (Items 1-21, 24, 26 And 27) P69 Rev. 8/07

70 TWO-SPEED POINT ROW CLUTCH PRC023(FF47b/A7274/TWL71/TWL18/A10054) L.H. Two-Speed Point Row Clutch Shown (Used On L.H.Side Of Planter) Input Shaft Jumper Wire Between Point Row Clutch Solenoids Connects To Planter Harness At Valve Block On Rear Center Frame Connects To Clutch Solenoids P70 Rev. 8/07

71 TWO-SPEED POINT ROW CLUTCH (Per Assy.) 1. GD Threaded Rod, ¼"-20 x 3 ½" G Hex Nut, ¼"-20 G Lock Washer, ¼" GD Allen Nut, ¼" G Hex Head Cap Screw, ¼"-20 x ¾" G Lock Washer, ¼" G Hex Nut, ¼" GD Threaded Rod, ⅜"-16 x 4 ¼" G Lock Nut, ⅜"-16 G Lock Washer, ⅜" G Hex Nut, ⅜" GD Spring 5. GA Hub/Sleeve Assembly W/Seals, Sleeve, Pins And Screws GD Seal GD Sleeve G Hex Socket Set Screw, 5 16"-18 x ¾" G Hex Socket Set Screw, 5 16"-18 x ¼" G Spring Pin, 5 32" x ⅞" G Spring Pin, ¼" x 1" 6. GD Actuator Arm 7. GD Bushing 8. GA Solenoid Complete GR Snap Ring GR Spring GR Boot GR Plunger 9. GD Mounting Plate 10. G Spring Pin, 3 16" x 2 ¼" 11. G Hex Socket Head Screw, No x ¼" 12. GD Spring, L.H. (Shown) 13. GD Stop Collar 14. GD Felt Washer 15. GA Hub W/Seal GD Seal 16. G External Inverted Snap Ring, 1 ½" 17. GD Output Sprocket, 28 Tooth 18. GD Rue Ring Cotter, 5 16" 19. G Hex Socket Head Screw, ¼"-20 x 1" GD Key 20. GD Input Shaft, R.H. Threads (Shown) GD Input Shaft, L.H. Threads 21. GD Input Sprocket, 28 Tooth 22. GD Coupler W/R.H. Threads (Shown) GD Coupler W/L.H. Threads 23. GA Hub W/Seal GD Seal 24. G Fork Terminal 25. GD Contact 26. GD Housing, Black GD Housing, Red 27. GA Jumper Wire W/Ring Terminals, " 28. GA Wiring Harness, 228", R.H. And L.H. Sides, 8 Row 36"/38" And R.H. Side, 12 Row 30" GA Wiring Harness, 264", L.H. Side, 12 Row 30" And R.H. Side, 12 Row 36"/38" GA Wiring Harness, 312", L.H. Side, 12 Row 36"/38" GA Wiring Harness, 252", R.H. Side, 16 Row 30" GA Wiring Harness, 300", L.H. Side, 16 Row 30" 29. GD Spring, R.H. P71 Rev. 8/07

72 TWO-SPEED POINT ROW CLUTCH WHEEL MODULE EXTENSION (TWL77g/TWL84b/TWL79a/TWL80) Output Sprocket TRAVEL See Inner Module Drive Input Sprocket TRAVEL TRAVEL P72 Rev. 8/07

73 TWO-SPEED POINT ROW CLUTCH WHEEL MODULE EXTENSION (Per Assy.) 1. GD Spring 2. G Spring Pin, ¼" x 1 ½" 3. GA Sprocket, 24 Tooth GA Sprocket, 15 Tooth GA Sprocket, 17 Tooth GA Sprocket, 27 Tooth GA Sprocket, 23 Tooth (From Transmission) GA Sprocket, 25 Tooth (From Transmission) GA Sprocket, 26 Tooth (From Transmission) 4. GA Sprocket, 28 Tooth 5. G Machine Bushing, 1", 10 Gauge 6. G Flangette 7. G Bearing, ⅞" Hex Bore, Spherical 8. G Carriage Bolt, 5 16"-18 x ¾" G Lock Washer, 5 16" G Hex Nut, 5 16" GD Shaft, ⅞" x 13 ¾" 10. GA Extension Bracket 11. G Hex Head Cap Screw, ¼"-20 x 1 ¼" G Washer, ¼" USS G Lock Washer, ¼" G Hex Nut, ¼" G Clevis Pin, 5 16" x ¾" G Retaining Ring, 5 16" 13. G Hex Head Cap Screw, ¼"-20 x 1" G Washer, ¼" USS G Lock Washer, ¼" G Hex Nut, ¼" See Contact Drive Wheel And Drive Shaft(s), Pages P60-P See Two-Speed Point Row Clutch, Pages P70 And P G Chain, No. 40, 74 Pitch Including Connector Link GR Connector Link, No G Chain, No. 40, 100 Pitch Including Connector Link GR Connector Link, No GA Overrunning Sprocket Assembly, R.H. GA Overrunning Sprocket Assembly, L.H. G External Retaining Ring, 1 ¼" GD L-Pin G Spring Pin, 3 16" x 1 ¼" G Cotter Pin, 5 32" x 1" GD Spring GA Block GA Sprocket W/Bushing, 30 Tooth 19. GD Hex Shaft, ⅞" x 13" 20. GA Idler W/Sprocket And Hardware GD Bushing, ¾" Long G Machine Bushing, ½", 14 Gauge G Hex Jam Nut, ½"-13, Grade 2 G Hex Head Cap Screw, ½"-13 x 2 ½" GA Sprocket W/Bearing, 18 Tooth (Continued On Following Page) P73 Rev. 8/07

74 TWO-SPEED POINT ROW CLUTCH WHEEL MODULE EXTENSION (Per Assy.) (Continued) 21. GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" 22. G Hex Head Cap Screw, ⅝"-11 x 4" G Lock Nut, ⅝"-11 G Hex Nut, ⅝" G Hex Head Cap Screw, ⅜"-16 x 10" G Lock Nut, ⅜" G External Inverted Snap Ring, 1 ½" 25. G Internal Inverted Snap Ring, ⅞" 26. GD Sleeve, 1 ¼" 27. GD Torsion Spring, R.H. (Used On L.H. Wrap Spring Wrench) (Shown) GD Torsion Spring, L.H. (Used On R.H. Wrap Spring Wrench) 28. GD Release Collar, Silver, L.H. (Shown) GD Release Collar, Gold, R.H. 29. GD Tightener Shaft, 3 ⅜" 30. GD Handle 31. G Machine Bushing, ⅞", 14 Gauge 32. G Hex Socket Button Head Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 33. G Vinyl Cap 34. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GA Sprocket Storage Rod 36. GD Lynch Pin, ¼" A. G1K381 - Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 24-33) (Shown) G1K380 1 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 24-33) P74 Rev. 8/07

75 ROW MARKER SPINDLE/HUB/BLADE MKR020(MKR4) (Per Assy.) 1. G Hex Head Cap Screw, ½"-20 x 1" G Lock Washer, ½" 2. GD Retainer 3. GD Disc Blade, Solid, 16" (Shown) GD Disc Blade, Notched, 16" (Optional) 4. GD Dust Cap 5. G Slotted Hex Nut, ⅝" G Cotter Pin, 5 32" x 1" 7. G Washer, ⅝" SAE 8. GA Bearing 9. GA Hub W/Cups, 4 Bolt GR Outer Cup GR Inner Cup 10. GA Bearing 11. GA Grease Seal 12. GA Rubber Seal 13. GA Spindle, R.H. GA Spindle, L.H. (Shown) 14. G Carriage Bolt, ½"-13 x 3 ½" G Machine Bushing, ½", 7 Gauge G Lock Washer, ½" G Hex Nut, ½" GA Depth Band 16. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Nut, 5 16"-18, Grade 8 A. GA Hub And Spindle Assembly, L.H. (Items 1, 2 And 4-13) GA Hub And Spindle Assembly, R.H. (Items 1, 2 And 4-13) P75 Rev. 8/07

76 ROW MARKER ASSEMBLY, 8 ROW 36"/38" AND 12 ROW 30" MKR019/MKR027(MKR14i/A11590) P76 Rev. 8/07

77 ROW MARKER ASSEMBLY, 8 ROW 36"/38" AND 12 ROW 30" (Per Assy.) 1. GA Arm W/Grease Fittings, Second Stage, 110", 12 Row 30" G Grease Fitting, ⅛" NPT GA Arm, Second Stage, 67", 8 Row 36"/38" 2. G Washer, 1 ¼" SAE (As Required) G Machine Bushing, 1 ¼", 10 Gauge (As Required) G Machine Bushing, 1 ¼", 18 Gauge (As Required) 3. GD Pin, 1 ¼" x 12 ¼" G Cotter Pin, ¼" x 2" 4. GA Arm W/Grease Fittings, First Stage G Grease Fitting, ⅛" NPT 5. GD Sleeve, 1" 6. GA Safety Lockup W/Detent Pins, 19 ⅜" G Detent Pin, ½" x 2 ½" 7. G Hex Head Cap Screw, ⅝"-11 x 5 ½" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 5" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 2" (If Applicable) GD Special Washer, ⅝", Hardened G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" GD Extension Tube, 45", 12 Row 30" GD Extension Tube, 60", 12 Row 30" (L.H. Even-Row Marker) (If Applicable) GD Extension Tube, 65", 8 Row 36"/38" 9. - See Row Marker (Cushion) Cylinder, Page P GD Pin, 1 ¼" x 8 ¼" G Cotter Pin, ¼" x 2" 11. GD Pin, 1 ¼" x 9 ½" G Cotter Pin, ¼" x 2" 12. GD Shim, 2 ½" x 7 ¼", 16 Gauge (As Required) 13. GA Mount 14. GA Stand, 20" (12 Row 30" Only) 15. GD U-Bolt, 2" x 2" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Bar 17. GD U-Bolt, 3" x 3" x ½"-13 G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" SAE G Lock Nut, ½" GA Molded Stop, 12 ¼" Long 20. GD Plate, 6" x 6" 21. GA Pin W/Grease Fitting, 1 ¼" x " G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" 22. GA Arm, First Stage 23. GA Pin W/Grease Fitting, 1 ¼" x 9 ½" G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" P77 Rev. 8/07

78 ROW MARKER ASSEMBLY, 12 ROW 36"/38" AND 16 ROW 30" MKR019/MKR023MKR027(MKR15j/A11569) P78 Rev. 8/07

79 ROW MARKER ASSEMBLY, 12 ROW 36"/38" AND 16 ROW 30" (Per Assy.) 1. GA Arm, Second Stage, 138 ¼", 12 Row 36"/38" GA Arm, Second Stage, 172 ¼", 16 Row 30" 2. GD Pin, 1 ¼" x 6 ½" G Cotter Pin, ¼" x 2" 3. G Special Washer, 1 ¼" (As Required) G Machine Bushing, 1 ¼", 10 Gauge (As Required) G Machine Bushing, 1 ¼", 18 Gauge (As Required) 4. GD Pin, 1 ¼" x 13 ¼" G Cotter Pin, ¼" x 2" 5. GA Arm W/Grease Fittings, First Stage, R.H. GA Arm W/Grease Fittings, First Stage, L.H. G Grease Fitting, ⅛" NPT 6. GA Safety Lockup W/Detent Pins, 19 ⅜" G Detent Pin, ½" x 2 ½" 7. G Hex Head Cap Screw, ⅝"-11 x 6 ½" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 6" (If Applicable) G Hex Head Cap Screw, ⅝"-11 x 2 ½" (If Applicable) GD Special Washer, ⅝", Hardened G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" GD Extension Tube, 75", 12 Row 36"/38" And 16 Row 30" (L.H. Even-Row Marker) (If Applicable) GD Extension Tube, 50", 16 Row 30" 9. - See Row Marker (Cushion) Cylinder, Page P GD Pin, 1 ¼" x 9 ½" G Cotter Pin, ¼" x 2" 11. GD Pin, 1 ¼" x 11 ½" G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Lock Nut, ⅜" GD Shim, 2 ½" x 12 ½", 16 Gauge (As Required) (Shown) GD Shim, 2 ½" x 8 ¼", 16 Gauge (As Required) 13. GA Mount 14. GA Stand, 30" 15. GD U-Bolt, 2" x 2" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Bar 17. GD U-Bolt, 3" x 3" x ½"-13 G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" SAE G Lock Nut, ½" GA Molded Stop, 12 ¼" Long 20. G Special Washer, 1 ¼" (As Required) 21. GD Plate, 7" x 7" 22. G Washer, 1 ¼" SAE G Machine Bushing, 1 ¼", 18 Gauge 23. GA Pin W/Grease Fitting, 1 ¼" x 13" G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" 24. GA Arm, First Stage, L.H. (Shown) GA Arm, First Stage, R.H. 25. GA Pin W/Grease Fitting, 1 ¼" x 11 ½" G Grease Fitting, ¼"-28 G Cotter Pin, ¼" x 1 ½" P79 Rev. 8/07

80 ROTATION CYLINDER, ALL SIZES (CYL11i) 1. GA Threaded Ball Joint End 2. G Hex Jam Nut, 1 ¼"-12, Grade 2 3. GD Gland 4. GD Rod 5. GD Piston 6. G Lock Nut, 1 ¼" A Barrel (Non-Stock Item) A. GA Cylinder Complete, 4" x 16" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) U-Cup, (1) Wiper, (1) Seal, (2) Cast Iron Rings, (1) BU Ring, (1) Expander CENTER LIFT CYLINDER, ALL SIZES (CYL39c) Port Type Rephasing 1. GD Clevis 2. G Set Screw, ¼"-20 x ¼" 3. GD Cap 4. GD Rod 5. GD Gland 6. GD Piston 7. G Lock Nut, 1" GA Barrel 9. G Hex Head Cap Screw, ⅜"-16 x 2 ¼" G Lock Nut, ⅜" G6408-H04-O 1 Hex Socket Head Plug W/O-Ring, 7 16"-20 O-Ring GR O-Ring A. GA Cylinder Complete, 3" x 48" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (2) BU Rings, (1) Wiper, (1) U-Cup, (1) Piston Seal, (2) Cast Iron Rings, (1) Expander P80 Rev. 8/07

81 WING LIFT CYLINDER, 8 AND 12 ROW CYL031/CYL011(CYL45d) ITEM PART NO. QTY DESCRIPTION Port Type Rephasing 1. GA Rod Assembly W/Grease Fitting G Grease Fitting, ¼" GD Gland 3. GD Piston 4. G Lock Nut, 1" A Barrel (Non-Stock Item) A. GA Cylinder Complete, 4 ¼" x 6" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (1) Wiper, (2) O-Rings, (1) BU Ring, (1) U-Cup, (1) Seal, (2) Cast Iron Rings, (1) Expander WING LIFT CYLINDER, 16 ROW CYL031/CYL011(CYL41c) 1. G Set Screw, ¼"-20 x ¼" 2. GD Cap 3. GA Rod Assembly W/Grease Fitting G Grease Fitting, 3 16", Drive-In 4. GD Gland 5. GD Piston 6. G Lock Nut, 1" A Barrel (Non-Stock Item) Port Type Rephasing A. GA Cylinder Complete, 3" x 6" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (2) BU Rings, (1) Expander, (1) Wiper, (1) U-Cup, (1) Piston Seal, (2) Cast Iron Rings P81 Rev. 8/07

82 TRANSPORT LATCH CYLINDER, ALL SIZES CYL035/CYL050(CYL9c) 1. G Internal Retaining Ring, " 2. GD Gland 3. GD Rod 4. GD Piston 5. G Lock Nut, ½" D Barrel (Non-Stock Item) 7. GD Tension Bushing, 1" x 2" Long 8. GD End Cap A. GA Cylinder Complete, 1 ½" x 2 ½" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (3) O-Rings, (2) BU Rings, (1) Wiper, (1) T-Seal, (1) Bronze Bushing, (1) Seal, (1) U-Cup TONGUE LOCK CYLINDER, ALL SIZES CYL035(CYL9d) 1. G Internal Retaining Ring, " 2. GD Gland 3. GD Rod 4. GD Piston 5. G Lock Nut, ½" D Barrel (Non-Stock Item) 7. GD Tension Bushing, 1" x 2" Long 8. GD End Cap A. GA Cylinder Complete, 1 ½" x 2 ½" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (3) O-Rings, (2) BU Rings, (1) Wiper, (1) T-Seal, (1) Bronze Bushing, (1) Seal, (1) U-Cup P82 Rev. 8/07

83 TONGUE CYLINDER, 8 ROW 36"/38" WITH Y HITCH (CYL12f) 3 / 4 "-16 O-Ring Port 7 / 16 "-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 1 / 4 " G Connector W/O-Ring, 3 / 4 "-16 Male JIC To 7 / 16 "-20 O-Ring GR O-Ring 7. A Barrel (Non-Stock Item) 8. GA Steel Hydraulic Line, / 16 " 9. G Bulkhead Tube Union, 3 / 4 "-16 Male JIC 10. GD Bracket 11. G Lock Nut, 3 / 4 " G Hex Head Cap Screw, 3 / 8 "-16 x 5 / 8 " G Lock Washer, 3 / 8 " 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 36" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P83 Rev. 8/07

84 TONGUE CYLINDER, 8 ROW 36"/38" WITH T HITCH, 12 ROW 30" WITH Y HITCH (CYL12f) 3 / 4 "-16 O-Ring Port 7 / 16 "-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. GA Barrel 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 60" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P84 Rev. 8/07

85 TONGUE CYLINDER, 12 ROW 30" WITH T HITCH, 12 ROW 36"/38" AND 16 ROW 30" WITH Y HITCH CYL036(CYL12f) ¾"-16 O-Ring Port 7 16"-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. GA Barrel 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 84" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P85 Rev. 8/07

86 TONGUE CYLINDER, 12 ROW 36"/38" AND 16 ROW 30" WITH T HITCH CYL036(CYL12f) ¾"-16 O-Ring Port 7 16"-20 O-Ring Port 1. GA Rod Assembly 2. GD Gland 3. GD Spacer 4. GD Piston 5. G Lock Nut, 1 ¼" G Connector W/O-Ring, ¾"-16 Male JIC To 7 16"-20 O-Ring GR O-Ring 7. GA Barrel 8. GA Steel Hydraulic Line, " 9. G Bulkhead Tube Union, ¾"-16 Male JIC 10. GD Bracket 11. G Lock Nut, ¾" G Hex Head Cap Screw, ⅜"-16 x ⅝" G Lock Washer, ⅜" 13. G Hose Clamp, No. 52 A. GA Cylinder Complete, 3" x 108" (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring, (1) Wear Ring, (1) Wiper, (1) U-Cup, (1) T-Seal P86 Rev. 8/07

87 WING LOCK CYLINDER, ALL SIZES CYL032(CYL3f) 1. GA Rod Assembly 2. GD Gland 3. A Barrel (Non-Stock Item) 4. GD Piston 5. G Lock Nut, 7 / 8 "-14 A. GA Cylinder Complete, 2 1 / 2 " x 20 1 / 16 " (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (1) T-Seal, (2) O-Rings, (1) BU Ring, (1) U-Cup, (1) Wiper MARKER (Cushion) CYLINDER, ALL SIZES (CYL3d) 1. GA Rod Assembly 2. GD Gland 3. A Barrel (Non-Stock Item) 4. G Cotter Pin, 1 / 8 " x 1 3 / 4 " 5. GD Piston 6. G Slotted Hex Nut, 7 / 8 "-14 A. GA Cylinder Complete, 2 1 / 2 " x 20 1 / 16 " (Part Number Stamped On Barrel) B. GR Seal Kit, Includes: (1) T-Seal, (2) O-Rings, (1) BU Ring, (1) Cast Iron Ring, (1) Wiper, (1) U-Cup P87 Rev. 8/07

88 JUNCTION BLOCK - LOCATED ON R.H. SIDE OF CENTER PIVOT VVB036(TWL24) 1. GD Manifold Block 2. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 3. G Connector W/O-Ring, ⅞"-14 Male JIC To ¾"-16 O-Ring GR O-Ring 4. G Hex Head Cap Screw, ⅜"-16 x 5" G Lock Washer, ⅜" G Hex Nut, ⅜"-16 P88 Rev. 8/07

89 VALVE BLOCKS - LOCATED ON REAR CENTER FRAME VVB034(TWL25e) 1. G Hex Head Cap Screw, 5 16"-18 x 2 ¾" G Lock Washer, 5 16" 2. 2 See Check Valve, Page P See Solenoid Valve, Page P GD Block 5. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 6. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 7. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To ⅞"-14 O-Ring GR O-Ring 8. G Plug W/O-Ring, ¾"-16 O-Ring GR O-Ring 9. 2 See Flow Control Valve, Page P GD Block 11. G6408-H06-O 6 Hex Socket Head Plug W/O-Ring, 9 16"-18 O-Ring GR O-Ring 12. G Connector W/O-Ring, ¾"-16 Male JIC To ⅞"-14 O-Ring GR O-Ring 13. G Plug W/O-Ring, ⅞"-14 O-Ring GR O-Ring 14. GD Sleeve, 1" Long 15. GD Cover 16. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Washer, 5 16" 17. G Hex Head Cap Screw, 5 16"-18 x ½" G Lock Washer, 5 16" G Hex Nut, 5 16" GA Terminal Strip W/Screws, No. 6, 14 Terminal GR Screw, No x ¼" 19. G Phillips Pan Head Machine Screw, No x ¾", Stainless Steel 20. G Phillips Pan Head Machine Screw, No x ¾", Stainless Steel 21. GA Terminal Strip Mount 22. G Phillips Pan Head Machine Screw, No x ½", Stainless Steel P89 Rev. 8/07

90 VALVE BLOCK - LOCATED ON HITCH VVB035(TWL26f) P90 Rev. 8/07

91 VALVE BLOCK - LOCATED ON HITCH 1. GD Block 2. - See Solenoid Valve, Page P See Pressure Relief Valve, Page P92 4. G Connector W/O-Ring, 9 16"-18 Male JIC To O-Ring GR O-Ring 5. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 6. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 7. G Swivel Elbow, 90, 9 16"-18 Male JIC To Female 8. G Elbow W/O-Ring, 90, 9 16"-18 Male JIC To O-Ring GR O-Ring 9. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To O-Ring GR O-Ring 10. G6408-H06-O 2 Hex Socket Head Plug W/O-Ring, 9 16"-18 O-Ring GR O-Ring See Hose Take-Up, Pages P48 And P GD Terminal Strip Mount 13. G Phillips Flat Head Machine Screw, No x ⅝", Stainless Steel 14. GA Terminal Strip W/Screws, No. 6, 8 Terminal GR Screw, No x ¼" 15. G Phillips Pan Head Machine Screw, No x ⅝", Stainless Steel See Electrical Components, Pages P100 And P101 P91 Rev. 8/07

92 SOLENOID VALVE VVB019(TWL27c/TWL18/PLTR75c/A9481) Solenoid Valve Holds Load In One Direction 1. GR Special Hex Nut, ½" G1K274 1 Coil Kit W/Coil, Contacts, Housings And Fork Terminals GD Housing, Black GD Contact G Fork Terminal 3. GR Cartridge A. G1K275 - Solenoid Valve Kit W/Solenoid Valve, Contacts, Housings And Fork Terminals GD Housing, Black GD Contact G Fork Terminal B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring Contact Fork Terminal Housing FLOW CONTROL VALVE VVB020(TWL28) A. GA Flow Control Valve B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring PRESSURE RELIEF VALVE VVB020(TWL29) A. GA Pressure Relief Valve, 1000 PSI B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring P92 Rev. 8/07

93 RELIEF VALVE (LOCATED ON HITCH), 8 AND 12 ROW (Prior To Serial Number ) (TWL147) STYLE A B 1. GR Body 2. GR Cartridge A. GA8129A - Relief Valve Complete B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring STYLE B (TWL171) 1. GR Body 2. GR Cartridge A. GA8129B - Relief Valve Complete B. GR Seal Kit, Includes: (2) O-Rings, (2) BU Rings CHECK VALVE VVB020(TWL30) A. GA Check Valve B. GR Seal Kit, Includes: (2) O-Rings, (1) BU Ring P93 Rev. 8/07

94 HYDRAULIC HOSES AND FITTINGS ON HITCH (TWL107c/TWL107b) STYLE A Relief Valve NOTE: See page P93 for additional information. 8 AND 12 ROW (Prior To Serial Number ) * * * Tongue Cylinder A3 B3 Transport Latch Cylinder B5 A5 A4 B4 C2 A5 D2 A3 B3 Valve Bock A2 B2 - Located On Hitch NOTE: See A1 B1 pages P90 B5 and P91 for A6 B6 additional information. C1 D1 B6 A6 Tongue Lock Cylinder C1 Hose Support/Junction - Located On L.H. Side Of Center Pivot D1 B1 A4 B4 Rotation Cylinder A1 P94 Rev. 8/07

95 HYDRAULIC HOSES AND FITTINGS ON HITCH 1. GD ISO Coupler 2. *A Hose Assembly, ½" x 138", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 159", 8 Row 36"/38" T Hitch *A Hose Assembly, ½" x 147", 12 Row 30" Y Hitch *A Hose Assembly, ½" x 182", 12 Row 30" T Hitch *A Hose Assembly, ½" x 178", 12 Row 36"/38" And 16 Row 30" Y Hitch *A Hose Assembly, ½" x 209", 12 Row 36"/38" And 16 Row 30" T Hitch 3. *A Hose Assembly, ⅜" x 156", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 203", 8 Row 36"/38" T Hitch *A Hose Assembly, ⅜" x 191", 12 Row 30" Y Hitch *A Hose Assembly, ⅜" x 240", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 246", 12 Row 36"/38" And 16 Row 30" Y Hitch *A Hose Assembly, ⅜" x 300", 12 Row 36"/38" And 16 Row 30" T Hitch 4. G Connector W/O-Ring, ⅞"-14 Male JIC To O-Ring GR O-Ring 5. *A Hose Assembly, ½" x 17", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 43", 8 Row 36"/38" T And 12 Row 30" Y Hitch *A Hose Assembly, ½" x 68", 12 Row 30" T Hitch, 12 Row 36"/38" Y Hitch And 16 Row 30" Y Hitch *A Hose Assembly, ½" x 90", 12 Row 36"/38" T Hitch And 16 Row 30" T Hitch 6. *A Hose Assembly, ¼" x 90", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 130", 8 Row 36"/38" T Hitch *A Hose Assembly, ¼" x 110", 12 Row 30" Y Hitch *A Hose Assembly, ¼" x 157", 12 Row 30" T Hitch And 12 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 204", 12 Row 36"/38" T Hitch *A Hose Assembly, ¼" x 168", 16 Row 30" Y Hitch *A Hose Assembly, ¼" x 216", 16 Row 30" T Hitch 7. G Elbow W/O-Ring, 90, 9 16"-18 Male JIC To ¾"-16 O-Ring GR O-Ring 8. G Swivel Elbow, 45, 9 16"-18 Male JIC To Female 9. G Connector W/O-Ring, 9 16"-18 Male JIC To ¾"-16 O-Ring GR O-Ring 10. *A Hose Assembly, ¼" x 32", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 40", 8 Row 36"/38" T Hitch, 12 Row 30" Y / T Hitch, 12 Row 36"/38" Y / T Hitch And 16 Row 30" Y / T Hitch 11. *A Hose Assembly, ½" x 112", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 68", 8 Row 36"/38" T Hitch *A Hose Assembly, ½" x 72", 12 Row 30" T Hitch *A Hose Assembly, ½" x 120", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ½" x 78", 12 Row 36"/38" And 16 Row 30" T Hitch *A Hose Assembly, ½" x 128", 16 Row 30" Y Hitch 12. *A Hose Assembly, ⅜" x 116", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 76", 8 Row 36"/38" T Hitch *A Hose Assembly, ⅜" x 79", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 125", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ⅜" x 84", 12 Row 36"/38" And 16 Row 30" T Hitch *A Hose Assembly, ⅜" x 130", 16 Row 30" Y Hitch 13. G Bulkhead Tube Union, ⅞"-14 Male JIC 14. G Bulkhead Tube Union, ¾"-16 Male JIC 15. *A Hose Assembly, ¼" x 125", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 85", 8 Row 36"/38" And 12 Row 30" T Hitch *A Hose Assembly, ¼" x 130", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ¼" x 95", 12 Row 36"/38" T Hitch And 16 Row 30" T Hitch *A Hose Assembly, ¼" x 136", 16 Row 30" Y Hitch 16. *A Hose Assembly, ⅜" x 60", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 74", 8 Row 36"/38" T Hitch *A Hose Assembly, ⅜" x 68", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ⅜" x 97", 12 Row 36"/38" And 16 Row 30" T Hitch *A Hose Assembly, ⅜" x 79", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 80", 16 Row 30" Y Hitch 17. *A Hose Assembly, ⅜" x 48", 8 Row 36"/38" Y Hitch (If Applicable) *A Hose Assembly, ⅜" x 72", 8 Row 36"/38" T And 12 Row 30" Y Hitch (If Applicable) *A Hose Assembly, ⅜" x 96", 12 Row 36"/38" Y Hitch, 12 Row 30" T Hitch And 16 Row 30" Y Hitch (If Applicable) 18. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 19. G Union, ⅞"-14 Male JIC * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for quote. P95 Rev. 8/07

96 HYDRAULIC HOSES AND FITTINGS ON HITCH (TWL107d/TWL107b) STYLE B STYLE A Tongue Cylinder A3 B3 Transport Latch Cylinder B5 A5 A4 B4 C2 A5 D2 A3 B3 Valve Bock A2 B2 - Located On Hitch NOTE: See A1 B1 pages P90 B5 and P91 for A6 B6 additional information. C1 D1 B6 A6 Tongue Lock Cylinder C1 Hose Support/Junction - Located On L.H. Side Of Center Pivot D1 B1 A4 B4 Rotation Cylinder A1 P96 Rev. 8/07

97 HYDRAULIC HOSES AND FITTINGS ON HITCH 1. GD ISO Coupler 2. *A Hose Assembly, ½" x 156", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 203", 8 Row 36"/38" T Hitch *A Hose Assembly, ½" x 191", 12 Row 30" Y Hitch *A Hose Assembly, ½" x 250", 12 Row 30" T Hitch *A Hose Assembly, ½" x 246", 12 Row 36"/38" And 16 Row 30" Y Hitch *A Hose Assembly, ½" x 300", 12 Row 36"/38" And 16 Row 30" T Hitch 3. *A Hose Assembly, ⅜" x 156", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 203", 8 Row 36"/38" T Hitch *A Hose Assembly, ⅜" x 191", 12 Row 30" Y Hitch *A Hose Assembly, ⅜" x 240", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 246", 12 Row 36"/38" And 16 Row 30" Y Hitch *A Hose Assembly, ⅜" x 300", 12 Row 36"/38" And 16 Row 30" T Hitch 4. *A Hose Assembly, ⅜" x 48", 8 Row 36"/38" Y Hitch (If Applicable) *A Hose Assembly, ⅜" x 72", 8 Row 36"/38" T And 12 Row 30" Y Hitch (If Applicable) *A Hose Assembly, ⅜" x 96", 12 Row 36"/38" Y Hitch, 12 Row 30" T Hitch And 16 Row 30" Y Hitch (If Applicable) 5. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 6. *A Hose Assembly, ¼" x 90", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 130", 8 Row 36"/38" T Hitch *A Hose Assembly, ¼" x 110", 12 Row 30" Y Hitch *A Hose Assembly, ¼" x 157", 12 Row 30" T Hitch And 12 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 204", 12 Row 36"/38" T Hitch *A Hose Assembly, ¼" x 168", 16 Row 30" Y Hitch *A Hose Assembly, ¼" x 216", 16 Row 30" T Hitch 7. G Elbow W/O-Ring, 90, 9 16"-18 Male JIC To ¾"-16 O-Ring GR O-Ring 8. G Swivel Elbow, 45, 9 16"-18 Male JIC To Female 9. G Connector W/O-Ring, 9 16"-18 Male JIC To ¾"-16 O-Ring GR O-Ring 10. *A Hose Assembly, ¼" x 32", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 40", 8 Row 36"/38" T Hitch, 12 Row 30" Y / T Hitch, 12 Row 36"/38" Y / T Hitch And 16 Row 30" Y / T Hitch 11. *A Hose Assembly, ½" x 112", 8 Row 36"/38" Y Hitch *A Hose Assembly, ½" x 68", 8 Row 36"/38" T Hitch *A Hose Assembly, ½" x 72", 12 Row 30" T Hitch *A Hose Assembly, ½" x 120", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ½" x 78", 12 Row 36"/38" And 16 Row 30" T Hitch *A Hose Assembly, ½" x 128", 16 Row 30" Y Hitch 12. *A Hose Assembly, ⅜" x 116", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 76", 8 Row 36"/38" T Hitch *A Hose Assembly, ⅜" x 79", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 125", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ⅜" x 84", 12 Row 36"/38" And 16 Row 30" T Hitch *A Hose Assembly, ⅜" x 130", 16 Row 30" Y Hitch 13. G Bulkhead Tube Union, ⅞"-14 Male JIC 14. G Bulkhead Tube Union, ¾"-16 Male JIC 15. *A Hose Assembly, ¼" x 125", 8 Row 36"/38" Y Hitch *A Hose Assembly, ¼" x 85", 8 Row 36"/38" And 12 Row 30" T Hitch *A Hose Assembly, ¼" x 130", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ¼" x 95", 12 Row 36"/38" T Hitch And 16 Row 30" T Hitch *A Hose Assembly, ¼" x 136", 16 Row 30" Y Hitch 16. *A Hose Assembly, ⅜" x 60", 8 Row 36"/38" Y Hitch *A Hose Assembly, ⅜" x 74", 8 Row 36"/38" T Hitch *A Hose Assembly, ⅜" x 68", 12 Row 30"/36"/38" Y Hitch *A Hose Assembly, ⅜" x 97", 12 Row 36"/38" And 16 Row 30" T Hitch *A Hose Assembly, ⅜" x 79", 12 Row 30" T Hitch *A Hose Assembly, ⅜" x 80", 16 Row 30" Y Hitch * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for quote. P97 Rev. 8/07

98 HYDRAULIC HOSES AND FITTINGS ON PLANTER FRAME (TWL105b) 16 Row Shown (Two Wing Lift Cylinders Per Wing) 8 And 12 Row (One Wing Lift Cylinder Per Wing) Hose Support/Junction - Located On L.H. Side Of Center Pivot NOTE: See pages P94-P97 for additional information. B1 C1 A1 A5 B5 D1 L.H. Row Marker Cylinder L.H. Wing Lift Cylinder(s) SLAVE D4 L.H. Wing Lock Cylinder A7 B7 C2 Center Lift Cylinder REAR L.H. MASTER D2 D1 D3 D1 Center Lift Cylinder FRONT R.H. MASTER 1. *A Hose Assembly, ⅜" x 260", 8 Row 36"/38" *A Hose Assembly, ⅜" x 272", 12 Row 30" *A Hose Assembly, ⅜" x 318", 12 Row 36"/38" *A Hose Assembly, ⅜" x 332", 16 Row 30" 2. G Elbow W/O-Ring, 90, ¾"-16 Male JIC To O-Ring GR O-Ring 3. G Connector W/O-Ring, ¾"-16 Male JIC To 7 / 16 "-20 O-Ring GR O-Ring 4. *A Hose Assembly, ½" x 62", 8 Row 36"/38" And 12 Row 36"/38" *A Hose Assembly, ½" x 58", 12 Row 30" And 16 Row 30" 5. *A Hose Assembly, ⅜" x 62", 8 Row 36"/38" And 12 Row 36"/38" *A Hose Assembly, ⅜" x 58", 12 Row 30" And 16 Row 30" 6. G Tee, ¾"-16 Male JIC, 16 Row 30" 7. *A Hose Assembly, ⅜" x 230", 8 Row 36"/38" *A Hose Assembly, ⅜" x 250", 12 Row 30" *A Hose Assembly, ⅜" x 284", 12 Row 36"/38" *A Hose Assembly, ⅜" x 272", 16 Row 30" 8. *A Hose Assembly, ⅜" x 66" 9. G Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 10. *A Hose Assembly, ⅜" x 42" 11. G Bulkhead Tee, ⅞"-14 Male JIC 12. G Reducer, ⅞"-14 Female JIC To ¾"-16 Male JIC 13. *A Hose Assembly, ⅜" x 30" P98 Rev. 8/07

99 HYDRAULIC HOSES AND FITTINGS ON PLANTER FRAME D1 C1 B1 D1 A1 B1 Junction Block - Located On R.H. Side Of Center Pivot NOTE: See page P88 for additional information. C1 A1 B4 A4 R.H. Row Marker Cylinder R.H. Wing Lift Cylinder(s) SLAVE R.H. Wing Lock Cylinder B6 A6 D5 C3 C2 D4 C3 D5 D2 C1 D3 A5 B6 A7 B7 B1 A1 A4 B4 A6 B6 Valve Block - Located On Rear Center Frame NOTE: See page P89 for additional information. 14. *A Hose Assembly, ⅜" x 52" 15. *A Hose Assembly, ⅜" x 40", 16 Row 30" 16. *A Hose Assembly, ½" x 41" 17. *A Hose Assembly, ½" x 30" 18. *A Hose Assembly, ⅜" x 30" 19. *A Hose Assembly, ⅜" x 204", 8 Row 36"/38" *A Hose Assembly, ⅜" x 225", 12 Row 30" *A Hose Assembly, ⅜" x 280", 12 Row 36"/38" *A Hose Assembly, ⅜" x 288", 16 Row 30" 20. *A Hose Assembly, ⅜" x 30" 21. *A Hose Assembly, ⅜" x 168", 8 Row 36"/38" *A Hose Assembly, ⅜" x 186", 12 Row 30" *A Hose Assembly, ⅜" x 234", 12 Row 36"/38" *A Hose Assembly, ⅜" x 216", 16 Row 30" 22. G6400-L-08 - Long Connector W/O-Ring, ¾"-16 Male JIC To O-Ring GR O-Ring 23. *A Hose Assembly, ⅜" x 10 ½", 16 Row 30" 24. G Swivel Elbow, 90, ¾"-16 Male JIC To Female * Hydraulic hose is not stocked by KINZE Repair Parts, but can be made available on a special order basis. Call for P99 Rev. 8/07

100 ELECTRICAL COMPONENTS (TWL19a/TWL18/ELC14/ELC3a/ELC5c/MTR27a/ELC39/TWL26e/ELC8/A9481/ELC12b/MTR27t/A9689b/A10924ELC4/FF27b/FF27c/ELC38/A9201a/A9202a/TWL20g/ELC34/ELC35/ Socket Contact (Tractor) Pin Contact (Planter) Sealing Plug Amber Amber Red See Wing Frame, pages P52 and P53 for light brackets. For Planter Harness For Tractor Harness Planter Harness Harness Extension Tractor Harness 1. GA Ground Clamp 2. GD Contact 3. GD Housing, Black GD Housing, Red 4. GA Double Light Assembly (Shown) GA Double Light Assembly GR Red Lens GR Amber Lens GR Cover GR Rubber Grommet (4) GR Lamp Unit GR Bulb 5. GA Harness Extension, 42" 6. GD Sealing Plug, No GD Socket Contact, No GD Pin Contact, No. 14 P100 Rev. 8/07

101 ELECTRICAL COMPONENTS 9. GA Wiring Harness W/7 Terminal Female Connector, 786" (2 Light Connections), 12 Row 30" GA Wiring Harness W/7 Terminal Female Connector, 882" (2 Light Connections), 16 Row 30" GA Terminal Female Connector 10. GA Connector W/Cable Clamp, 23 Pin Capacity 11. GA Dust Cap W/Chain 12. GA Dust Cap W/Chain 13. GA Connector W/Cable Clamp, 23 Socket Capacity 14. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 15. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 16. GD Sealing Plug 17. GA Dust Plug (Black) 18. GA Wiring Harness W/Dust Cap, 516", 8 Row 36"/38" And 12 Row 30" GA Wiring Harness W/Dust Cap, 636", 12 Row 36"/38" And 16 Row 30" 19. GA Harness Extension W/Dust Caps, 180" 20. GA Indicator Light 21. GA Fuse Holder W/Spade, " 22. GD Fuse, 15 Amp, Type AGC 23. GD Fuse, MDL 10 Amp Delay Action 24. GR Hex Face Nut, 15 32"-32 GR Internal Tooth Lock Washer, 15 32" 25. GA Cover Plate (Shown) GA Cover Plate, Planters Equipped With Two-Speed Point Row Clutches 26. GR Pan Head Screw, No x ½" 27. GD O-Ring (If Applicable) 28. GA Switch, 3 Position Toggle, On-Off-On 29. GA Switch, 3 Position Toggle, Momentary On-Off-Momentary On 30. GA Switch, 2 Position Toggle, On-Off 31. GA Switch, Push Button W/Transformer 32. GD Mounting Bracket 33. G Washer, ¼" SAE 34. GA Knob 35. GR Cage Nut, ¼" G1K267 - Power Lead Adapter Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (3) Male Terminal Pins 37. G1K268 - Console Cable Connector Kit, Includes: (1) 3-Pin Connector, (1) Cable Clamp, (1) Lock Ring, (3) Female Terminal Pins 38. GA Power Lead Adapter 39. GA Wiring Harness W/Dust Cap And Power Cable 40. G7633X - Backlit Control Console Assembly W/Mounting Brackets, Short Harness W/Dust Cap And Power Cable G7639X - Backlit Control Console Assembly W/Mounting Brackets, Short Harness W/Dust Cap And Power Cable, Planters Equipped With Two-Speed Point Row Clutches 41. GD Insulated Clamp, ⅜" GD Insulated Clamp, 11 16" 42. GD Jumper, 7 16" 43. GA Jumper Wire W/Fork Terminal, 13" G Fork Terminal 44. GA Wiring Harness W/7 Terminal Female Connector, 714" (4 Light Connections), 8 Row 36"/38" GA Wiring Harness W/7 Terminal Female Connector, 870" (4 Light Connections), 12 Row 36"/38" GA Terminal Female Connector 45. GA Single Amber Light Assembly GR Amber Lens GR Rubber Grommet (2) GR Lamp Unit GR Bulb 46. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 47. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 48. GA Work Light Assembly 49. GD Bracket 50. G T-Bolt Clamp, 3 ½" Stainless Steel 51. GA Wiring Harness, 348" NOTE: See Point Row Clutch or Two-Speed Point Row Clutch for R.H. and L.H. Wiring Harness for the point row clutches. P101 Rev. 8/07

102 KPM I ELECTRONIC SEED MONITOR (MTR46b) Power Lead Adapter Adapter Harness Blue Extension Harness Planter Harness Blue Junction Y-Harness P102 Rev. 8/07

103 KPM I ELECTRONIC SEED MONITOR 1. GA Power Lead Adapter 2. G1K267 - Power Lead Adapter Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (3) Male Terminal Pins 3. G1K268 - Console Cable Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (1) Lock Ring, (3) Female Terminal Pins 4. GA KPM I Backlit Console W/Mounting Bracket, Fuse Holder And Fuse, Power Lead Adapter (Item 1), Brush (Item 8) And Dust Plug (Item 16) GR Mounting Bracket, KPM I GR Console Mounting Bracket Hardware Package (Includes 2 Knobs And ¼" Hardware) GA Fuse Holder GD Fuse 5. - Included In Tractor/Planter Wiring Harness, See Items 18 And 39, Pages P100 And P GA Planter Harness W/Dust Caps, 6 Row (9 Connectors) GA Planter Harness W/Dust Caps, 8 Row (12 Connectors) GA Planter Harness W/Dust Caps, 12 Row (16 Connectors) GA Planter Harness W/Dust Caps, 16 Row (20 Connectors) GD Dust Cap 7. GA Seed Tube W/Computerized Sensor GR Sensor Only GA Seed Tube (With Holes For Sensor Installation) 8. GR Brush 9. G Hex Head Cap Screw, ¼"-20 x ½" G Washer, ¼" SAE G Lock Washer, ¼" G Hex Nut, ¼" GA Adapter Harness, 1' 11. GA Extension Harness W/Dust Cap, 15' GA Extension Harness W/Dust Cap, 30' GD Dust Cap 12. GA Junction Y-Harness W/Dust Cap GD Dust Cap 13. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals G1K362-3-Pin Female Connector Kit (Blue), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 14. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals G1K363-3-Pin Male Connector Kit (Blue), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 15. GD Sealing Plug 16. GA Dust Plug (Black) GA Dust Plug (Blue) 17. GA Dust Plug (Black) GA Dust Plug (Blue) P103 Rev. 8/07

104 KPM II STACK-MODE ELECTRONIC SEED MONITOR (MTR43ss/A10901a) Shaft Rotation Sensor Radar Distance Sensor Magnetic Distance Sensor (MDS) Power Lead Adapter SMM Blue KPM II Stack-Mode Blue Radar Y-Cable Adapter Harness Planter Harness Extension Harness Blue Acre Counter Switch Kit Magnetic Distance Sensor (MDS) Adapter 1. GA Radar Distance Sensor W/20' Cable 2. GA Radar Sensor Pipe/Mounting Bracket Package 3. G1K323-4-Pin Connector Kit W/Female Housing, Includes: (4) Pins, (1) Cable Clamp 4. GA Magnetic Distance Sensor 5. GD Magnetic Distance Sensor Pulse Wheel 6. GD Insulated Clamp, ⅜" 7. GD Bracket 8. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Spring Wave Washer P104 Rev. 8/07

105 KPM II STACK-MODE ELECTRONIC SEED MONITOR 10. GA SMM Backlit Console W/Mounting Bracket And Dust Plug (Item 36) GR Mounting Bracket, KPM II Stack-Mode And SMM Consoles GR Console Mounting Bracket Hardware Package (Includes 2 Knobs And ¼" Hardware) 11. GA Power Lead Adapter 12. GA Monitor/Radar Adapter Cable, 10" 13. G1K267 - Power Lead Adapter Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (3) Male Terminal Pins 14. G1K268 - Console Cable Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (1) Lock Ring, (3) Female Terminal Pins 15. GA KPM II Backlit Console W/Mounting Bracket, Fuse Holder And Fuse, Power Lead Adapter (Item 11), Brush (Item 22), Dust Plug (Item 33) And Monitor/Radar Adapter Cable, 10" (Item 12) GR Mounting Bracket, KPM II GR Console Mounting Bracket Hardware Package (Includes 4 Knobs And ¼" Hardware) GA Fuse Holder GD Fuse 16. G1K322-4-Pin Connector Kit W/Male Housing, (4) Female Socket Contacts And (1) Cable Clamp See Tractor /Planter Wiring Harness, Items 18 And 39 On Pages P100 And P GA Planter Harness W/Dust Caps, 6 Row (9 Connectors) GA Planter Harness W/Dust Caps, 8 Row (12 Connectors) GA Planter Harness W/Dust Caps, 12 Row (16 Connectors) GA Planter Harness W/Dust Caps, 16 Row (20 Connectors) GD Dust Cap 19. GA Seed Tube W/Computerized Sensor GR Sensor Only GA Seed Tube (With Holes For Sensor Installation) 20. GA Magnetic Distance Sensor Adapter (Analog To Digital) 21. G Hex Head Cap Screw, ¼"-20 x ½" G Washer, ¼" SAE G Lock Washer, ¼" G Hex Nut, ¼" GR Brush 23. GR Radar Y-Cable (Used To Connect Radar Distance Sensor For Multiple Functions) 24. GA Adapter Harness, 1' 25. GA Extension Harness W/Dust Cap, 15' GA Extension Harness W/Dust Cap, 30' GD Dust Cap 26. G1K364 - Rotation Sensor Mount Kit, Includes: (2) Mounts, (2) GD " x 7" U-Bolts, (4) G10228 Lock Washers, (4) G10102 Hex Nuts, (1) Instruction 27. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 28. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 29. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals G1K362-3-Pin Female Connector Kit (Blue), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 30. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals G1K363-3-Pin Male Connector Kit (Blue), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 31. GD Sealing Plug 32. G1K249 - Acre Counter Switch Kit 33. GA Dust Plug (Black) GA Dust Plug (Blue) 34. GA Dust Plug (Black) GA Dust Plug (Blue) 35. GR Rotation Sensor 36. GD Mount 37. G Pan Head Screw, No x 1 ¼" G Washer, No. 10 SAE G Hex Nut, No GD Cover 39. GD Spring 40. GD Spring Mount 41. GR Actuator 42. G Pan Head Machine Screw, No x 1 ¼", Stainless Steel G Lock Washer, No. 8, Internal/External, Stainless Steel G Hex Nut, No. 8-32, Stainless Steel A. GA Magnetic Distance Sensor And Mounting Package (Items 4-9) P105 Rev. 8/07

106 KPM III ELECTRONIC SEED MONITOR (MTR59) Shaft Rotation Sensor Radar Distance Sensor Magnetic Distance Sensor (MDS) Shaft Rotation Sensor Power Lead Adapter Blue Radar Y-Cable Adapter Harness Planter Harness Extension Harness Blue Acre Counter Switch Kit Magnetic Distance Sensor (MDS) Adapter 1. GA Radar Distance Sensor W/20' Cable 2. GA Radar Sensor Pipe/Mounting Bracket Package 3. G1K323-4-Pin Connector Kit W/Female Housing, Includes: (4) Pins, (1) Cable Clamp 4. GA Magnetic Distance Sensor 5. GD Magnetic Distance Sensor Pulse Wheel 6. GD Insulated Clamp, ⅜" 7. GD Bracket 8. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Spring Wave Washer P106 Rev. 8/07

107 KPM III ELECTRONIC SEED MONITOR 10. GD Mount 11. GA Power Lead Adapter 12. GA Monitor/Radar Adapter Cable, 10" 13. G1K267 - Power Lead Adapter Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (3) Male Terminal Pins 14. G1K268 - Console Cable Connector Kit, Includes: (1) Cable Clamp, (1) 3-Pin Connector, (1) Lock Ring, (3) Female Terminal Pins 15. GA KPM III Backlit Console W/Brush (Item 22), Dust Plug (Item 33), Mounting Bracket Assembly, Console Mounting Bracket Hardware And Power Harness GA Mounting Bracket Assembly, Includes: (2) Mounting Brackets, (2) Connector Halves, (1) Compression Spring, (1) Tension Knob, (1) ¼"-20 x 1 ¾" Hex Head Cap Screw, (1) ¼" Plastic Washer, (1) ¼" Steel Washer GR Console Mounting Bracket Hardware Package, Includes: (3) No x ⅝" Hex Socket Pan Head Screws, (3) No. 10 Lock Washers GR Power Harness 16. G1K322-4-Pin Connector Kit W/Male Housing, (4) Female Socket Contacts And (1) Cable Clamp See Tractor /Planter Wiring Harness, Items 18 And 39 On Pages P100 And P GA Planter Harness W/Dust Caps, 6 Row (9 Connectors) GA Planter Harness W/Dust Caps, 8 Row (12 Connectors) GA Planter Harness W/Dust Caps, 12 Row (16 Connectors) GA Planter Harness W/Dust Caps, 16 Row (20 Connectors) GD Dust Cap 19. GA Seed Tube W/Computerized Sensor GR Sensor Only GA Seed Tube (With Holes For Sensor Installation) 20. GA Magnetic Distance Sensor Adapter (Analog To Digital) 21. GD Shaft Sensor Mount 22. GR Brush 23. GR Radar Y-Cable (Used To Connect Radar Distance Sensor For Multiple Functions) 24. GA Adapter Harness, 1' 25. GA Extension Harness W/Dust Cap, 15' GA Extension Harness W/Dust Cap, 30' GD Dust Cap 26. G1K364 - Rotation Sensor Mount Kit, Includes: (2) Mounts, (2) GD " x 7" U-Bolts, (4) G10228 Lock Washers, (4) G10102 Hex Nuts, (1) Instruction 27. G1K321-2-Pin Female Connector Kit (Black), Includes: (3) 2-Pin Female Housings, (6) Pin Contacts, (6) Seals 28. G1K320-2-Pin Male Connector Kit (Black), Includes: (3) 2-Pin Male Housings, (6) Socket Contacts, (6) Seals 29. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals G1K362-3-Pin Female Connector Kit (Blue), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 30. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals G1K363-3-Pin Male Connector Kit (Blue), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 31. GD Sealing Plug 32. G1K249 - Acre Counter Switch Kit 33. GA Dust Plug (Black) GA Dust Plug (Blue) 34. GA Dust Plug (Black) GA Dust Plug (Blue) 35. GR Rotation Sensor 36. GD Mount 37. G Pan Head Screw, No x 1 ¼" G Washer, No. 10 SAE G Hex Nut, No GD Cover 39. GD Spring 40. GD Spring Mount 41. GR Actuator 42. G Pan Head Machine Screw, No x 1 ¼", Stainless Steel G Lock Washer, No. 8, Internal/External, Stainless Steel G Hex Nut, No. 8-32, Stainless Steel 43. G Hex Head Cap Screw, ⅜"-16 x 8" G Lock Washer, ⅜" G Hex Nut, ⅜"-16 A. GA Magnetic Distance Sensor And Mounting Package (Items 4-9) P107 Rev. 8/07

108 PLANTER MONITOR MODULE (PMM) (MTR60/MTR63/PMM01/MTR65/MTR61/MTR64/MTR62/PMM02) Shaft Rotation Sensor Magnetic Distance Sensor (MDS) Planter Harness Blue Magnetic Distance Sensor (MDS) Adapter NOTE: See Ag Leader manual for Ag Leader Insight display and associated cab harness components. 1. G Hex Head Cap Screw, ⅜"-16 x 8" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Shaft Sensor Mount 3. GR Rotation Sensor 4. GR Actuator 5. GD Mount P108 Rev. 8/07

109 PLANTER MONITOR MODULE (PMM) 6. G Pan Head Screw, No x 1 ¼" G Washer, No. 10 SAE G Hex Nut, No GD Cover 8. G Pan Head Machine Screw, No x 1 ¼", Stainless Steel G Lock Washer, No. 8, Internal/External, Stainless Steel G Hex Nut, No. 8-32, Stainless Steel 9. GA Magnetic Distance Sensor 10. GD Magnetic Distance Sensor Pulse Wheel 11. GD Insulated Clamp, ⅜" 12. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Washer, ⅜" G Hex Nut, ⅜" GD Bracket 14. GD Spring Wave Washer 15. GA Dust Plug (Black) GA Dust Plug (Blue) 16. GA Dust Plug (Black) GA Dust Plug (Blue) 17. G1K248-3-Pin Female Connector Kit (Black), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals G1K362-3-Pin Female Connector Kit (Blue), Includes: (3) 3-Pin Female Housings, (9) Pin Contacts, (9) Seals 18. G1K252-3-Pin Male Connector Kit (Black), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals G1K363-3-Pin Male Connector Kit (Blue), Includes: (3) 3-Pin Male Housings, (9) Socket Contacts, (9) Seals 19. GD Sealing Plug 20. GA Module Cover Assembly W/Lock Clamps GA Lock Clamp G Phillips Pan Head Machine Screw, No x ⅝", Stainless Steel G Lock Nut W/Nylon Insert, No. 8-32, Stainless Steel 21. GD Bracket 22. GA Planter Monitor Module 23. G Hex Head Cap Screw, 5 16"-18 x ¾" G Lock Washer, 5 16" G Hex Nut, 5 16" GD U-Bolt, 5" x 7" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Spacer, 1½" x 9" 26. GD Support 27. GR Brush 28. GA Planter Harness W/Dust Caps, 6 Row (9 Connectors) GA Planter Harness W/Dust Caps, 8 Row (12 Connectors) GA Planter Harness W/Dust Caps, 12 Row (16 Connectors) GA Planter Harness W/Dust Caps, 16 Row (20 Connectors) GD Dust Cap 29. GA Seed Tube W/Computerized Sensor GR Sensor Only GA Seed Tube (With Holes For Sensor Installation) 30. GA Magnetic Distance Sensor Adapter (Analog To Digital) 31. GA Planter Monitor Cable A. GA Magnetic Distance Sensor And Mounting Package (Items 9-14) P109 Rev. 8/07

110 INTERPLANT PUSH ROW UNIT DRIVE PTD073/PTD076(RU134/TWL33n/TWL33o) 8 Row 36"/38" 12 Row 30"/36"/38" If Applicable (Viewed From Front Of Machine) STYLE A (Per Side) 1. G Machine Bushing, 1", 10 Gauge (As Required) 2. GD Lock Clamp 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 4. GA Hanger Bearing, ⅞" Hex Bore 5. GD Hex Shaft, ⅞" x 55" (No Holes), R.H. Side, 8 Row 36"/38" GD Hex Shaft, ⅞" x 84" (No Holes), L.H. Side, 8 Row 36"/38" GD Hex Shaft, ⅞" x 48" (No Holes), R.H. Side, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 66" (No Holes), L.H. Side, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 55" (No Holes), R.H. Side, 12 Row 36"/38" GD Hex Shaft, ⅞" x 84" (No Holes), L.H. Side, 12 Row 36"/38" 6. GD Hex Shaft, ⅞" x 49" (No Holes), Both Sides, 8 Row 36"/38" GD Hex Shaft, ⅞" x 90" (No Holes), Both Sides, 12 Row 30" GD Hex Shaft, ⅞" x 108" (No Holes), Both Sides, 12 Row 36"/38" GD Hex Shaft, ⅞" x 124" (No Holes), R.H. Side, 16 Row 30" GD Hex Shaft, ⅞" x 138" (No Holes), L.H. Side, 16 Row 30" 7. GD Hex Shaft, ⅞" x 24" (No Holes), 12 Row 30" W/Even-Row Push Row Unit GD Hex Shaft, ⅞" x 33" (No Holes), 16 Row 30" W/Even-Row Push Row Unit P110 Rev. 8/07

111 INTERPLANT PUSH ROW UNIT DRIVE (Per Side) 8. GA U-Joint W/Grease Fitting, Female, 18 ⅛" Long, 8 Row 36"/38" And 12 Row 36"/38" GA U-Joint W/Grease Fitting, Female, 10 ¼" Long, 12 Row 30" And 16 Row 30" GR Grease Fitting, 45, Metric GR Inboard Yoke And Outer Profile (10 ¼" U-Joint) GR Inboard Yoke And Outer Profile (18 ⅛" U-Joint) GR Cross And Bearing Kit GR Yoke, ⅞" Hex 9. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G External Inverted Snap Ring, 1 ½" 11. G Spring Pin, 5 32" x 7 16" 12. GR Lock Collar 13. GR Spring 14. GR Drive Shaft 15. GR Shim 16. GR Bushing 17. GR Sprocket, 19 Tooth 18. G Hex Socket Set Screw, ⅜"-16 x ¾" 19. GR Pin 20. GR Knurled Collar 21. GR Compression Spring 22. GD U-Bolt, 7" x 5" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GA Mount 24. G Chain, No. 40, 226 Pitch Including Connector Link GR Connector Link, No GD Spacer, 1 ¼" O.D. x ½" Long (If Applicable) 26. GA Sprocket W/Bearing, 18 Tooth 27. G Hex Head Cap Screw, ½"-13 x 2" G Machine Bushing, ½", 7 Gauge G Lock Washer, ½" G Hex Nut, ½" GD Hose Protector 29. GA Sprocket, 19 Tooth 30. GD Support Angle, R.H. 31. GD Support Angle, L.H. 32. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Coupler, 4" 34. GA U-Joint W/Grease Fitting, Male, 12 ¼" Long GR Grease Fitting, 45, Metric GR Inner Profile GR Inboard Yoke GR Spring Pin, 8mm x 50mm GR Cross And Bearing Kit GR Yoke, ⅞" Hex 35. G Hex Head Cap Screw, ⅝"-18 x 2 ¼" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Square Head Set Screw, ⅜"-16 x ⅝" A. GA Clutch Sprocket Assembly, 19 Tooth (Items 10-21) B. G1K269 - Lock Clamp Kit (Items 2 And 3) C. G1K331 - Clutch Sprocket Kit (Items 11, 16 And 17) P111 Rev. 8/07

112 INTERPLANT PUSH ROW UNIT DRIVE (RU134/TWL516) 8 Row 36"/38" 12 Row 30"/36"/38" If Applicable (Viewed From Front Of Machine) STYLE B (Per Side) 1. G Machine Bushing, 1", 10 Gauge (As Required) 2. GD Lock Clamp 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 4. GA Hanger Bearing, ⅞" Hex Bore 5. GD Hex Shaft, ⅞" x 55" (No Holes), R.H. Side, 8 Row 36"/38" GD Hex Shaft, ⅞" x 84" (No Holes), L.H. Side, 8 Row 36"/38" GD Hex Shaft, ⅞" x 48" (No Holes), R.H. Side, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 66" (No Holes), L.H. Side, 12 Row 30" And 16 Row 30" GD Hex Shaft, ⅞" x 55" (No Holes), R.H. Side, 12 Row 36"/38" GD Hex Shaft, ⅞" x 84" (No Holes), L.H. Side, 12 Row 36"/38" 6. GD Hex Shaft, ⅞" x 49" (No Holes), Both Sides, 8 Row 36"/38" GD Hex Shaft, ⅞" x 90" (No Holes), Both Sides, 12 Row 30" GD Hex Shaft, ⅞" x 108" (No Holes), Both Sides, 12 Row 36"/38" GD Hex Shaft, ⅞" x 124" (No Holes), R.H. Side, 16 Row 30" GD Hex Shaft, ⅞" x 138" (No Holes), L.H. Side, 16 Row 30" 7. GD Hex Shaft, ⅞" x 24" (No Holes), 12 Row 30" W/Even-Row Push Row Unit GD Hex Shaft, ⅞" x 33" (No Holes), 16 Row 30" W/Even-Row Push Row Unit 8. GA U-Joint W/Grease Fitting, Female, 18 ⅛" Long, 8 Row 36"/38" And 12 Row 36"/38" GA U-Joint W/Grease Fitting, Female, 10 ¼" Long, 12 Row 30" And 16 Row 30" GR Grease Fitting, 45, Metric GR Inboard Yoke And Outer Profile (10 ¼" U-Joint) GR Inboard Yoke And Outer Profile (18 ⅛" U-Joint) GR Cross And Bearing Kit GR Yoke, ⅞" Hex P112 Rev. 8/07

113 INTERPLANT PUSH ROW UNIT DRIVE (Per Side) 9. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G External Inverted Snap Ring, 1 ½" 11. G Spring Pin, 5 32" x 7 16" 12. GR Lock Collar 13. GR Spring 14. GR Drive Shaft 15. GR Shim 16. GR Bushing 17. GR Sprocket, 19 Tooth 18. G Hex Socket Set Screw, ⅜"-16 x ¾" 19. GR Pin 20. GR Knurled Collar 21. GR Compression Spring 22. GD U-Bolt, 7" x 5" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Plate (Shown) GD Plate 24. G Chain, No. 40, 226 Pitch Including Connector Link GR Connector Link, No GD Brace 26. GA Sprocket W/Bearing, 18 Tooth 27. G Hex Head Cap Screw, ½"-13 x 2" G Washer, ½" SAE G Lock Washer, ½" G Hex Nut, ½" G Hex Head Cap Screw, ½"-13 x 2" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GA Sprocket, 19 Tooth 30. GD Support Angle, R.H. 31. GD Support Angle, L.H. 32. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Coupler, 4" 34. GA U-Joint W/Grease Fitting, Male, 12 ¼" Long GR Grease Fitting, 45, Metric GR Inner Profile GR Inboard Yoke GR Spring Pin, 8mm x 50mm GR Cross And Bearing Kit GR Yoke, ⅞" Hex 35. G Hex Head Cap Screw, ⅝"-18 x 2 ¼" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" G Square Head Set Screw, ⅜"-16 x ⅝" A. GA Clutch Sprocket Assembly, 19 Tooth (Items 10-21) B. G1K269 - Lock Clamp Kit (Items 2 And 3) C. G1K331 - Clutch Sprocket Kit (Items 11, 16 And 17) P113 Rev. 8/07

114 DOUBLE DISC FERTILIZER OPENER AND MOUNT FOC007(PT25e/TWL34a/FRTZ208) To Pump To Opener Optional - Liquid Fertilizer Only P114 Rev. 8/07

115 DOUBLE DISC FERTILIZER OPENER AND MOUNT (Per Assy.) 1. GA Bracket 2. G Grease Fitting, ¼"-28, Taper Thread 3. G Cotter Pin, ⅛" x 1" 4. GD Lockup Pin 5. GD Hex Head Adjusting Bolt, ⅝"-18 x 3 ¼" G Hex Jam Nut, ⅝"-18, Grade 2 6. GA Spring 7. GD Bushing, 41 64" I.D. x 3 ½" Long 8. G Machine Bushing, ⅝" (.030" Thick) 9. G Rivet, ¼" x " 10. GD Dust Cap 11. G Hex Jam Nut, ⅝"-11, Grade 2 G Hex Jam Nut, ⅝"-11, L.H. Threads, Grade G Special Machine Bushing, ⅝" x 1" O.D. 13. GB Hub 14. GA Bearing 15. GD Disc Blade, 3.5 mm x 15" 16. GD Inner Scraper 17. GA Mount 18. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Washer, 5 16" 19. GA Drop Tube, Dry Fertilizer 20. GD Extension 21. G Hose Clamp, No GA Drop Tube, Liquid Fertilizer 23. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Washer, 5 16" SAE G Lock Nut, 5 16"-18, Grade GA Shank 25. GA Scraper Mount 26. GD Scraper 27. G Carriage Bolt, ⅜"-16 x 1" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ½"-13 x 4 ½" G Lock Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 5" G Lock Nut, ⅝" GD U-Bolt, 2 ½" x 2 ½" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GA Mount (One Per Opener) W/U-Bolts GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Check Valve, Low Rate A. GA Disc Blade And Bearing Assembly (Items 9 And 13-15) P115 Rev. 8/07

116 HD SINGLE DISC FERTILIZER OPENER (Soil Press Wheel) (TWL35d/TWL35b) P116 Rev. 8/07

117 HD SINGLE DISC FERTILIZER OPENER (Soil Press Wheel) (Per Assy.) 1. GD J-Bolt, ½"-13 G Lock Washer, ½" G Hex Nut, ½" See HD Single Disc Fertilizer Opener (Blade And Drop Tube), Pages P118 And P GD Lockup Bar 4. G Hex Head Cap Screw, ⅝"-11 x 3" 5. G Flanged Whiz Lock Screw, 5 16"-18 x ⅝", No Serration G Serrated Flange Nut, 5 16" GD Half Wheel Cover, Nylon 7. GA Bearing 8. GD Offset Tire 9. GD Half Wheel 10. G Hex Head Cap Screw, ½"-13 x ¾" G Lock Washer, ½" G Washer, ½" USS 11. G Lock Washer, ⅝" 12. G Machine Bushing, 1" (.048" Thick) 13. G Clevis Pin, ½" x 1 ¾" G Cotter Pin, ⅛" x ¾" 14. GD Yoke 15. G Washer, ⅝" SAE See HD Single Disc Fertilizer Opener (Blade And Drop Tube), Pages P118 And P GD Pivot Pin 18. G Spring Pin, ⅜" x 2" 19. GA Wheel Arm W/Grease Fitting, R.H. GA Wheel Arm W/Grease Fitting, L.H. (Shown) G Grease Fitting, ¼" GD Spring 21. GB Spring Washer 22. GD Special Bolt A. G1K215 - Lockup Kit (Items 1 And 3) B. GA Gauge Wheel Complete (Items 5-9) P117 Rev. 8/07

118 HD SINGLE DISC FERTILIZER OPENER (Blade And Drop Tube) FOC016/FOC007/FOC019(PT27c/FRTZ208) To Pump To Opener Optional - Liquid Fertilizer Only (Per Assy.) 1. GD Disc Blade, 18" GD Disc Blade, 20" (Optional) 2. GB Spindle 3. GA Seal 4. GA Bearing 5. GA Arm W/Cups And Washers GD Inner Cup GR Outer Cup G Washer, ⅝" SAE 6. G Hex Head Cap Screw, ⅝"-11 x 1 ½" 7. G Hex Head Cap Screw, ⅜"-16 x 1" G Lock Nut, ⅜" GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 9. GD Channel 10. GD Spring 11. G Grease Fitting, ⅛" NPT 12. G Hex Nut, ¾" GD Tap Block 14. GB Spring Seat 15. GA Bearing 16. G Machine Bushing, ", 10 Gauge 17. G Slotted Nut, 1" GD Dust Cap P118 Rev. 8/07

119 HD SINGLE DISC FERTILIZER OPENER (Blade And Drop Tube) (Per Assy.) 19. GD Pin G Lock Washer, 7 16" G Hex Nut, 7 16" GD Compression Spring 21. G Hair Pin Clip, No G Bolt, ½"-13 x 1 ½" G Lock Nut, ½" G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Washer, ⅜" USS G Lock Nut, ⅜" G Carriage Bolt, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" GD Scraper 26. GB Drop Tube, R.H., Dry Fertilizer GB Drop Tube, L.H., Dry Fertilizer (Shown) 27. GA Drop Tube, L.H., Liquid Fertilizer (Shown) GA Drop Tube, R.H., Liquid Fertilizer 28. GD Bar 29. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Washer, ⅜" 30. GD Clamp 31. GD Angle, R.H. GD Angle, L.H. (Shown) 32. G Hex Head Cap Screw, ½"-13 x 2" G Lock Nut, ½" G Machine Bushing, 1 ¼", 18 Gauge (As Required) 34. G Hex Head Cap Screw, ⅝"-11 x 3 ¼" G Washer, ⅝" SAE G Lock Washer, ⅝" 35. G Grease Fitting, ¼" GD Bushing, 2 ¼" 37. G Hex Head Cap Screw, ½"-13 x 1 ¾" G Lock Nut, ½" G Cotter Pin, 3 16" x 1 ½" 39. GA Opener Mount, R.H. GA Opener Mount, L.H. (Shown) 40. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Special Bolt 42. GB Rod Guide 43. GD Storage Strap 44. GD Sleeve, ½" x ½" Long 45. G Washer, ½" USS 46. GA Check Valve, Low Rate P119 Rev. 8/07

120 NOTCHED SINGLE DISC FERTILIZER OPENER (FRTZ208/B0405/TWL34e/TWL34g/FRTZ268/A12108) To Pump To Opener Optional - Liquid Fertilizer Only Liquid Fertilizer STYLE A (Part Number Stamped On Part) STYLE B (Part Number Stamped On Part) Dry Fertilizer P120 Rev. 8/07

121 NOTCHED SINGLE DISC FERTILIZER OPENER (Per Assy.) 1. G Hex Head Cap Screw, ½"-13 x 1 ½" G Hex Nut, ½" GB Mount 3. GB Arm, 13 ½" 4. G Grease Fitting, ¼" GD Bushing, ¾" O.D. x ½" Long 6. GA Compression Spring Assembly 7. G Hex Head Cap Screw, ⅜"-16 x 1 ¾" G Washer, ⅜" USS G Lock Nut, ⅜" GD Sleeve, " Long 9. GA Pivot Arm, L.H. (Shown) GA Pivot Arm, R.H. 10. GD Scraper, L.H. (Shown) GD Scraper, R.H. 11. G Hex Head Cap Screw, ⅜"-16 x ¾" 12. G Carriage Bolt, ⅜"-16 x 2" G Lock Nut, ⅜" G Hex Head Cap Screw, 5 16"-18 x ⅞" G Lock Washer, 5 16" G Washer, 5 16" USS 14. GD Stepped Spacer, 3" Long 15. GA Hub W/Bearing GA Double Row Bearing 16. G Hex Head Cap Screw, ⅝"-11 x 5 ½" GD Washer, 1 ½" O.D., 7 Gauge, Hardened G Lock Nut, ⅝" G Hex Head Cap Screw, ⅝"-11 x 5" G Washer, ⅝" USS G Machine Bushing, 1 ½", 18 Gauge (As Required) G Lock Nut, ⅝" GD Disc Blade, Notched, 16 ¾" 19. G Hex Head Cap Screw, ½"-13 x 6" G Washer, ½" SAE G Lock Nut, ½" GD U-Bolt, 1 ½" x 2 ½" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GB Knife, L.H. (Shown) GB Knife, R.H. 22. GA Drop Tube, L.H., Liquid Fertilizer (Shown) GA Drop Tube, R.H., Liquid Fertilizer 23. GA Drop Tube, L.H., Dry Fertilizer (Shown) GA Drop Tube, R.H., Dry Fertilizer 24. GA Check Valve, Low Rate 25. GA Mount W/U-Bolts, Liquid Fertilizer GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Mount W/U-Bolts, L.H., Dry Fertilizer GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Mount W/U-Bolts, R.H., Dry Fertilizer GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GB Mount, L.H. (Shown) GB Mount, R.H. 29. GA Drop Tube, Liquid Fertilizer (Shown) GA Drop Tube, Liquid Fertilizer P121 Rev. 8/07

122 RESIDUE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER DFC024(FRTZ165l) P122 Rev. 8/07

123 RESIDUE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER (Per Assy.) 1. - See Notched Single Disc Fertilizer Opener, Pages P120 And P GD Bushing, 1 ⅓" Long 3. GD Adjustment Lever 4. G Spring Pin, ¼" x 1 ¼" 5. G Hex Head Cap Screw, ½"-13 x 7" G Lock Nut, ½" G Hex Head Cap Screw, ⅝"-11 x 7 ½" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GD Sleeve, 2 ⅛" Long 8. GD Spring 9. G Carriage Bolt, ⅜"-16 x 2" G Washer, ⅜" SAE G Lock Nut, ⅜" GA Mount W/Grease Fitting, L.H. (Shown) GA Mount W/Grease Fitting, R.H. G Grease Fitting, ¼" G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Lock Nut, 5 16"-18, Grade GD Dust Cap 13. GD Wheel, 12 Tine, ⅜" x 12" 14. GA Hub W/Bearings GA Bearing 15. GD Backing Plate 16. GD Spacer, 11 16" I.D. x ½" Long 17. GD Spacer 18. G Carriage Bolt, ⅝"-11 x 3" G Hex Jam Nut, ⅝"-11, Grade GD Spring, L.H. (Shown) GD Spring, R.H. A. GA Wheel Assembly, 12 Tine, L.H. (Items 11 And 13-15)(Shown) GA Wheel Assembly, 12 Tine, R.H. (Items 11 And 13-15) P123 Rev. 8/07

124 DEPTH/GAUGE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER (FRTZ256) Three Depth Adjustment Holes P124 Rev. 8/07

125 DEPTH/GAUGE WHEEL ATTACHMENT FOR NOTCHED SINGLE DISC FERTILIZER OPENER (Per Assy.) 1. G Hex Head Cap Screw, ⅝"-11 x 3" 2. GD Special Washer, ⅝", Hardened 3. - See Notched Single Disc Fertilizer Opener, Pages P120 And P GA Blade Mount 5. G Machine Bushing, 1", 10 Gauge 6. GA Wheel Mount, L.H. (Shown) GA Wheel Mount, R.H. 7. GD Spacer 8. GD Half Wheel 9. GD Offset Tire 10. GA Bearing 11. GD Half Wheel Cover, Nylon 12. G Flanged Whiz Lock Screw, 5 16"-18 x ¾", No Serration G Serrated Flange Nut, 5 16" G Special Machine Bushing, ⅝" x 1" O.D. (As Required) A. GA Gauge Wheel Complete (Items 8-12) P125 Rev. 8/07

126 DRY FERTILIZER DRIVE (TWL37f) (Per Side) 1. G Chain, No. 40, 88 Pitch Including Connector Link GR Connector Link, No GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" 3. GD Shear Coupler 4. G Cotter Pin, 3 16" x 2" 5. GD Shaft, ⅞" x 7 ½" 6. GA Sprocket, 15 Tooth GA Sprocket, 19 Tooth GA Sprocket, 30 Tooth GA Sprocket, 33 Tooth GA Sprocket, 35 Tooth 7. G Spring Pin, ¼" x 1 ½" 8. GA Special Bearing, ⅞" Hex Bore x 1.6" 9. G Hex Head Cap Screw, ½"-13 x 1 ¼" G Lock Nut, ½"-13 P126 Rev. 8/07

127 DRY FERTILIZER DRIVE (Per Side) 10. GA Sprocket Storage Rod 11. GD Lynch Pin, ¼" 12. GD Shaft, ⅞" x " 13. GD Spring 14 G Grease Fitting, ¼" See Dry Fertilizer Couplers/Shafts, Pages P130 And P GA Bearing, ⅞" Hex Bore, Cylindrical 17. G Machine Bushing, 1", 10 Gauge 18. GD Sleeve, ⅝" I.D. x ⅞" O.D. x 3 ¼" Long 19. GD Sleeve, 1 ¼" O.D. x ⅝" Long 20. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" SAE G Lock Washer, ½" G Hex Nut, ½" G Chain, No. 40, 130 Pitch Including Connector Link GR Connector Link, No GA Sprocket, 24 Tooth 23. G Carriage Bolt, ½"-13 x 4 ½" G Washer, ½" SAE G Lock Nut, ½" GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" G Hex Head Cap Screw, ⅜"-16 x 2 ½" G Lock Nut, ⅜" GD U-Bolt, 7" x 5" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Mount, L.H. (Shown) GA Mount, R.H. 27. GA Transmission Plate, L.H. (Shown) GA Transmission Plate, R.H. 28. GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) (Shown) GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench) 29. GD Handle 30. G Hex Socket Button Head Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 31. G Internal Inverted Snap Ring, ⅞" 32. G External Inverted Snap Ring, 1 ½" 33. GD Tightener Shaft, 4 ⅞" 34. G Vinyl Cap 35. GD Sleeve, 1 ¼" 36. GD Release Collar, Gold, R.H. (Shown) GD Release Collar, Silver, L.H. A. G1K378 1 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 28-36) (Shown) G1K379 - Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 28-36) P127 Rev. Rev. 3/058/07

128 DRY FERTILIZER HOPPER AND MOUNTS DFC009/DFC018(TWL36) P128 Rev. 8/07

129 DRY FERTILIZER HOPPER AND MOUNTS (Per Hopper) 1. GA Lid W/Retainers, Clips, Rivets, Rubber Straps And Hardware GD Front Clip GD Rear Retainer G Rivet, 3 16" x 13 32" GD Rubber Strap G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" GB Auger, R.H. 3. GB Auger, L.H. 4. G Hex Head Cap Screw, 5 16"-18 x 1 ½" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" GD Shaft 6. G Hex Head Cap Screw, ¼"-20 x 2", Stainless Steel G Hex Nut, ¼"-20, Stainless Steel 7. GD Strap 8. G Hair Pin Clip, No GD Baffle 10. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" G Hex Head Cap Screw, 5 16"-18 x 1 ¼" G Special Washer, ⅜" x 1 ½" O.D. GD Rubber Washer G Lock Washer, 5 16" G Hex Nut, 5 16" G Grease Fitting, ⅛" NPT 13. GD Hopper 14. GD Outlet Housing 15. G Carriage Bolt, 5 16"-18 x 1" G Hex Head Cap Screw, 5 16"-18 x 1 ¼" (If Applicable) G Washer, 5 16" USS (If Applicable) G Special Washer, ⅜" x 1 ½" O.D. GD Rubber Washer G Lock Washer, 5 16" G Hex Nut, 5 16" G Cotter Pin, ¼" x 2" 17. GB Bearing 18. G Hose Clamp, No G Hose Clamp, No GD Rubber Tube 21. GD U-Bolt, 7" x 5" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" G Hex Head Cap Screw, ½"-13 x 1 ½" G Lock Washer, ½" G Hex Nut, ½" GD Angle, L.H. 24. GA Mount, L.H. 25. GD Angle, R.H. 26. GA Mount, R.H. 27. GD Holder, Rubber Tube (As Required) A. GA Hopper Sub-Assembly (Items 8, 10 And 12-15) B. GA Hopper Hardware Box (Items 2-7, 9, 11, 16 And 17) P129 Rev. 8/07

130 DRY FERTILIZER COUPLERS/SHAFTS RH100594(TWL38a) 8 Row 36" 8 Row 38" 12 Row 30" 12 Row 36" 12 Row 38" 16 Row 30" L.H. Side Of Machine Shown Direction Of Travel P130 Rev. 8/07

131 DRY FERTILIZER COUPLERS/SHAFTS 1. - See Dry Fertilizer Drive, Pages P126 And P GD Coupler, 6" 3. G Cotter Pin, ¼" x 2" 4. GA U-Joint W/Grease Fitting, Male, 12 ¼" Long GR Yoke, ⅞" Hex GR Cross And Bearing Kit GR Inboard Yoke GR Inner Profile GR Grease Fitting, 45, Metric GR Spring Pin, 8mm x 50mm 5. GA U-Joint W/Grease Fitting, Female, " Long GR Yoke, ⅞" Hex GR Cross And Bearing Kit GR Inboard Yoke And Outer Profile GR Grease Fitting, 45, Metric 6. G Machine Bushing, 1", 10 Gauge 7. GD Coupler, 3" 8. GD Hex Shaft, ⅞" x 15 ½" (1 Hole) 9. G Spring Pin, ¼" x 1 ½" 10. GD Coupler, 1 ¾" 11. GA U-Joint W/Grease Fitting, Female, 10 ¼" Long GR Yoke, ⅞" Hex GR Cross And Bearing Kit GR Inboard Yoke And Outer Profile GR Grease Fitting, 45, Metric 12. GD Coupler, 4" 13. GD Hex Shaft, ⅞" x 24 ½" (1 Hole) 14. GD Hex Shaft, ⅞" x 13 ½" (1 Hole) 15. GD Coupler, 10 ¾" 16. G Square Head Set Screw, ⅜"-16 x ⅝" P131 Rev. 8/07

132 LIQUID FERTILIZER TANKS, SADDLES, SADDLE MOUNTS AND HOSES LFC021/LFC023/LFC030/LFC012(FRTZ201g) 8" Lid 1 1 / 4 " At Bottom Of Tank 3 / 4 " At Bottom And Top Of Tank Polypropylene Fitting Assemblies See Items 5 And G Elbow, 90, ¾" NPT To Barb 2. GD Band, 30" (4 Per Tank) 3. G Hose Clamp, No G Hose, ¾" x 72" (One Per Tank) 5. GA Tank W/Lid And Fittings, 30" x 150 Gallon, 8 Row Sizes (Qty. 2), 12/16 Row Sizes (Qty. 4) GR Lid W/Vent, 8" (Top Of Tank) GR ¾" Polypropylene Fitting Assembly (Overflow Fitting, Nut, Bushing And O-Ring) (Top And Bottom Of Tank) GR Overflow Fitting GR ¼" Polypropylene Fitting Assembly (Nut, Bushing And O-Ring) (Bottom Of Tank) P132 Rev. 8/07

133 LIQUID FERTILIZER TANKS, SADDLES, SADDLE MOUNTS AND HOSES 6. GD Pad, 8" x 14' (For Two 30" Tanks) 7. GA Tank Mount (2 Per Tank) 8. GD Mounting Angle (2 Per Tank) 9. G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GD U-Bolt, 5" x 7" x ¾"-10 G Lock Washer, ¾" G Hex Nut, ¾" G Adapter, 1 ¼" NPT To Barb 12. GD J-Bolt, 5 16"-18 (8 Per Tank) G Lock Nut W/Nylon Insert, 5 16"-18, Grade 8 (8 Per Tank) 13. G Hose Clamp, No GA Shutoff Valve, 1 ¼" NPT GR Body O-Ring GR Stem O-Ring GR Teflon Seat GR Ball GR Handle 15. G Elbow, 90, 1 ¼" Male NPT To Female 16. G Close Nipple, 1 ¼" NPT 17. G Plug, ¾" NPT 18. G Tee, 1 ¼" Barb 19. G Hose, 1 ¼" x 32', 8 Row 36"/38" And 12 Row 30" G Hose, 1 ¼" x 40', 12 Row 36"/38" And 16 Row 30" 20. G Tee, 2" Female NPT 21. G Reducing Bushing, 2" Male NPT To 1 ¼" Female 22. GD Dust Plug, 2" Male Cam Lock 23. GD Adapter, 2" Female NPT To Cam Lock 24. GD Dust Cap, 2" Cam Lock 25. G Elbow, 45, 2" Male NPT To Female 26. GD Adapter, 2" Male NPT To Cam Lock 27. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GA Shutoff Valve, 2" NPT 29. G Elbow, 90, 2" NPT To Barb 30. G Hose Clamp, No. 36, Stainless Steel 31. G Hose, 2" x 12', 8 Row G Hose, 2" x 18', 12/16 Row 32. GA Quick Fill Mount, 2" 33. G Close Nipple, 2" NPT 34. G Hex Head Cap Screw, ¾"-10 x 8" G Washer, ¾" USS G Lock Washer, ¾" G Hex Nut, ¾"-10 P133 Rev. 8/07

134 LIQUID FERTILIZER PISTON PUMP MOUNT AND GROUND DRIVE WHEEL (TWL219rr) Model LM-4405-R 48 Tooth Drive Sprocket And 18 Tooth Driven Sprocket 18 Tooth Sprocket 48 Tooth Sprocket 1. G Hex Head Cap Screw, ⅝"-11 x 7 ½" G Lock Washer, ⅝" G Hex Nut, ⅝" GA Wheel Arm Mount 3. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 4. G Hex Head Cap Screw, 5 / 8 "-11 x 1 ¾" GD Special Washer, ⅝", Hardened G Lock Nut, ⅝" GA Spring Mount 6. GD Pin, 1 ¼" x 13 ½" G Cotter Pin, ¼" x 2" 7. GA Arm W/Grease Fittings G Grease Fitting, ⅛" NPT 8. GA Wheel, 5" x 15" 9. GD Valve Stem P134 Rev. 8/07

135 LIQUID FERTILIZER PISTON PUMP MOUNT AND GROUND DRIVE WHEEL 10. G Hex Head Cap Screw, ⅝"-11 x 6 ½" GD Special Washer, ⅝", Hardened 11. GA Spring Mount 12. GB Washer 13. GD Compression Spring 14. GA Spring Guide 15. G Hex Head Cap Screw, ⅝"-11 x 12" G Lock Nut, ⅝" G Hex Head Cap Screw, ¾"-10 x 2" G Lock Washer, ¾" 17. G Hex Head Cap Screw, ¾"-10 x 1 ¾" G Lock Washer, ¾" G Hex Nut, ¾" GD Hose Holder 19. GR Sprocket, 18 Tooth See Liquid Fertilizer Piston Pump (Crankcase Assembly), Pages P138 And P139 GR Offset Link, No See Liquid Fertilizer Piston Pump (Cylinder Assembly), Pages P140 And P G Hex Head Cap Screw, ⅝"-11 x 1 ½" G Washer, ⅝" USS G Lock Washer, ⅝" G Hex Nut, ⅝" GA Pump Mount 24. G Hex Head Cap Screw, ½"-13 x 1 ½" G Washer, ½" USS G Lock Washer, ½" G Hex Nut, ½" GD Scraper 26. G Hex Head Cap Screw, ⅝"-11 x 3 ½" G Washer, ⅝" SAE G Lock Washer, ⅝" G Hex Nut, ⅝" GA Idler Sprocket W/Bearing, 15 Tooth 28. GD Spacer, 11 16" I.D. x 1 ¼" Long 29. GD Tire, 7.60" x 15", 8 Ply (Specify Brand*) 30. GA Spindle 31. GA Seal 32. GA Bearing 33. GR Lug Nut, ½" G Sprocket, 48 Tooth 35. G Hex Head Cap Screw, 5 16"-18 x 1" G Lock Washer, 5 16" 36. GD Shoulder Nut, 1 ¼"-12 UNF-2A 37. GA Hub W/Cups And Studs, 5 Bolt GR Cup GR Stud 38. G Chain, No. 2050, 62 Pitch Including Connector Link, Used With L-4405 Piston Pump G Chain, No. 2050, 63 Pitch Including Connector And Offset Link, Used With NGP-7075 Piston Pump GR Connector Link, No GR0200 `- Offset Link, No GD Lynch Pin, ¼" * Specific brand requests will be supplied only as available from current KINZE Repair Parts stock. If a specific brand requested is not in stock, the brand available will be supplied. Different brand tires may have different diameters. Change in tire brand may affect rates. Field checks are recommended after any P135 Rev. 8/07

136 LIQUID FERTILIZER FLOW DIVIDER MOUNT AND HOSES (FRTZ280/FRTZ298) P136 Rev. 8/07

137 LIQUID FERTILIZER FLOW DIVIDER MOUNT AND HOSES 1. G Hose, ⅜" x 160', 12 Row 30" G Hose, ⅜" x 120', 8 Row 36"/38", 12 Row 36"/38" And 16 Row 30" 2. G Hose Clamp, No GD Adapter, ¼" NPT To ⅜" Barb 4. - See Liquid Fertilizer Piston Pump Flow Divider, Pages P144 And P G Plug, ¼" NPT 6. G Reducing Bushing, 1" Male NPT To ¾" Female, Stainless Steel (If Applicable) 7. GA Support, ¾" NPT 8. GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" G Elbow, 90, ¾" Female NPT 10. G Adapter, ¾" NPT To Barb 11. GA Strainer Complete GR Screen, No. 40 Mesh GR Gasket GR Y-Body GR End Cap 12. G Hose Clamp, No G Adapter, 1 ¼" NPT To Barb 14. G Reducing Bushing, 1 ½" Male NPT To 1 ¼" Female 15. G Elbow, 90, 1 ¼" NPT To Barb ¼" Hose, See Liquid Fertilizer Tanks, Saddles, Saddle Mounts And Hoses, Pages P132 And P G Hose Clamp, No G Coupler, ¾" Female NPT 19. G Hose, ¾" x 200" 20. G Pipe Nipple, ¾" NPT x 1 ½" Long 21. G Elbow, 90, ¾" Male NPT To Female 22. G Reducing Bushing, 1 ½" Male NPT To ¾" Female 23. G Elbow, 90, ¾" NPT To Barb See Liquid Fertilizer Piston Pump, Pages P42 And P G Reducing Bushing, 1 ½" Male NPT To 1 ¼" Female 26. G Close Nipple, 1 ¼" NPT 27. G Elbow, 90, 1 ¼" Male NPT To Female See Liquid Fertilizer Piston Pump, Pages P138-P141 P137 Rev. 8/07

138 LIQUID FERTILIZER PISTON PUMP (Crankcase Assembly) (PT38a/GR1100) Model L-4405 P138 Rev. 8/07

139 LIQUID FERTILIZER PISTON PUMP (Crankcase Assembly) 1. - See Liquid Fertilizer Piston Pump Mount And Ground Drive Wheel, Pages P134 And P G Square Head Set Screw, ⅜"-16 x ⅝" 3. GR Spacer 4. G Hex Head Cap Screw, 5 16"-18 x 1" 5. GR Housing 6. GR Repair Kit, Includes Item 5 On Liquid Fertilizer Piston Pump (Cylinder Assembly), Pages P140 And P GR Bearing 8. GR Name Plate 9. G Hex Head Cap Screw, 5 16"-18 x ½" 10. GR Crankcase 11. GR Vent Plug See Liquid Fertilizer Piston Pump (Cylinder Assembly), Pages P140 And P GR Adjustment Wrench 14. GR Plug 15. GR Disc 16. GR Connecting Rod 17. GR Large Eccentric 18. GR Small Eccentric 19. GR Eccentric Pin 20. GR Sleeve 21. GR Setting Arm Key 22. GR Woodruff Key 23. GR Crankshaft 24. GR Bearing 25. GR Cover Plate 26. GR Square Head Cap Screw, ⅜"-16 x 1 ¾" 27. GR Scale 28. G Lock Nut, ⅜" GR Flange 30. G Hex Head Cap Screw, ⅝"-11 x 4 ½" G Hex Nut, ⅝" GR Arm 32. G Hex Socket Head Set Screw, 5 16"-18 x ⅜" 33. G Hex Head Cap Screw, ⅜"-16 x 1 ½" GR Rubber Washer G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜"-16 A. GA Piston Pump Complete Less Sprocket (Model L-4405), Includes: Crankcase Assembly (Items 2-33 On This Page) And Cylinder Assembly (Items 1-22 On Pages P140 And P141) P139 Rev. 8/07

140 LIQUID FERTILIZER PISTON PUMP (Cylinder Assembly) (PT39a) Model L-4405 P140 Rev. 8/07

141 LIQUID FERTILIZER PISTON PUMP (Cylinder Assembly) 1. - See Liquid Fertilizer Piston Pump (Crankcase Assembly), Pages P138 And P G Hex Head Cap Screw, ⅜"-16 x 8" G Hex Nut, ⅜" GR Discharge Manifold 4. GR Discharge Valve 5. GR Repair Kit, Includes Item 6 On Liquid Fertilizer Piston - Pump (Crankcase Assembly), Pages P138 And P G Hex Head Cap Screw, ⅜"-16 x 5 ½" G Hex Nut, ⅜" GR Outboard Cylinder 8. GR Suction Valve 9. GR Suction Manifold 10. G Hex Head Cap Screw, 5 16"-18 x 1" 11. GR Flange Packing Washer 12. GR Plunger 13. GR Inboard Cylinder 14. GR Stuffing Box Insert 15. GR Retaining Ring 16. GR Washer 17. GR Packing Spring 18. GR Outboard Stuffing Box 19. GR Crosshead Guide 20. GR Piston Rod 21. GR Pin P141 Rev. 8/07

142 LIQUID FERTILIZER PISTON PUMP Uses 18 Tooth Sprocket (A12335a/GR1808) Model NGP-7055 P142 Rev. 8/07

143 LIQUID FERTILIZER PISTON PUMP Uses 18 Tooth Sprocket 1. GR Flange Cover Assembly G Hex Head Cap Screw, 5 16"-18 x ⅞" 2. GR Connecting Rod Assembly 3. GR Spacer Assembly G Hex Socket Head Set Screw, 5 16"-18 x ⅜" 4. GR Plug 5. GR Vent Plug 6. GR Woodruff Key 7. GR Eccentric Pin 8. GR Pin 9. GR Bearing 10. GR Setting Hub Assembly 11. GR Stuffing Box Insert 12. GR Sprocket, 18 Tooth 13. GR Adjustment Wrench 14. GR Setting Pointer Assembly 15. GR Repair Kit, Includes: (6) Gaskets, (9) O-Rings, (4) Washers, (1) Retaining Ring, (2) Oil Seals, (1) Snap Ring, (1) Thrust Washer, (1) Rod Bushing, (2) Flange Plunger Packings, (2) Packing Springs, (2) Rod Vee Packing Sets 16. GR Discharge Valve Assembly 17. GR Suction Valve Assembly 18. GR Setting Arm Key 19. GR Bearing 20. G Carriage Bolt, ⅜"-16 x 2" G Lock Nut, ⅜" G Hex Head Head Cap Screw, ⅜"-16 x 1 ½" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜"-16 A. GA Piston Pump Complete W/18 Tooth Sprocket (Model NGP-7055) P143 Rev. 8/07

144 LIQUID FERTILIZER PISTON PUMP FLOW DIVIDER (FRTZ159/PT40a/FRTZ202c) Model FD-1200 Flow Divider, 12 Outlet Model FD-2000 Flow Divider, 20 Outlet ¾" NPT 1" NPT P144 Rev. 8/07

145 LIQUID FERTILIZER PISTON PUMP FLOW DIVIDER 1. GR Plug 2. GR Hex Socket Head Screw, ¼"-20 x ¾", Stainless Steel GR Lock Washer, ¼", Stainless Steel 3. GR Cap 4. GR Needle Assembly W/Seal Kit (Item 22) 5. GR Seal Kit, Includes: (3) O-Rings, (1) Seal, (1) Spring, (1) Stainless Steel Sleeve 6. GR Sleeve 7. GR Body, 12 Outlet 8. G Hex Socket Head Plug, ¼" NPT, Stainless Steel 9. GR Cap 10. GR Needle Assembly W/Seal Kit (Item 22) 11. GR Seal Kit, Includes: (3) O-Rings, (1) Seal, (1) Spring 12. GR Sleeve 13. GR Body, 20 Outlet 14. GR Sleeve, 1" O.D. x ½" Long, Stainless Steel A. GA Liquid Fertilizer Piston Pump Flow Divider Complete, 12 Outlet (Model FD-1200) (Items 1-7) (8/12 Row Planters) B. GA Liquid Fertilizer Piston Pump Flow Divider Complete, 20 Outlet (Model FD-2000) (Items 1, 2 And 8-14) (16 Row Planters) P145 Rev. 8/07

146 LIQUID FERTILIZER SQUEEZE PUMP DRIVE (TWL46e) (Per Side) 1. GA Idler W/Bolt-On Sprockets GD Sprocket, 12 Tooth GD Sleeve, " Long G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Head Cap Screw, ⅜"-16 x 1 ¾" 2. GD Lock Clamp 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Flange Nut, 5 16"-18, No Serration 4. G Machine Bushing, 1", 10 Gauge (As Required) 5. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Lock Washer, 5 16" G Hex Nut, 5 16" G Clevis Pin, 5 16" x 1" G Retaining Ring, 5 16" 7. GD Spring P146 Rev. 8/07

147 LIQUID FERTILIZER SQUEEZE PUMP DRIVE (Per Side) 8. GA Sprocket, 15 Tooth GA Sprocket, 19 Tooth GA Sprocket, 32 Tooth GA Sprocket, 34 Tooth GA Sprocket, 46 Tooth GA Sprocket, 62 Tooth (Optional) 9. GD Hex Shaft, ⅞" x 48" (1 Hole), 8 Row GD Hex Shaft, ⅞" x 54" (1 Hole), 12/16 Row 10. G Hex Head Cap Screw, 5 16"-18 x 2" G Lock Washer, 5 16" G Hex Nut, 5 16" G Cotter Pin, 3 16" x 2" 12. GD Lynch Pin, ¼" 13. GA Sprocket Storage Rod 14. GD Shear Coupler See Liquid Fertilizer Squeeze Pump, Pages P148-P GA Pump Mount, L.H. 17. GA Pump Mount, R.H. 18. G Bearing, ⅞" Hex Bore, Spherical 19. G Flangette 20. GA Drive Plate W/Grease Fitting GA Drive Plate W/Grease Fitting (Shown) G Grease Fitting, ¼" GD U-Bolt, 7" x 5" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD U-Bolt, 5" x 7" x ⅝"-11 G Lock Washer, ⅝" G Hex Nut, ⅝" GD Coupler 24. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Washer, ⅜" USS G Lock Washer, ⅜" G Hex Nut, ⅜" G Chain, No. 40, 170 Pitch Including Connector Link GR Connector Link, No See Seed Rate Transmission And Row Unit Drill Shafts, Pages P64 And P GD Sleeve, 1 ¼" 28. GD Release Collar, Silver, L.H. (Shown) GD Release Collar, Gold, R.H. 29. GD Torsion Spring, R.H. (Used In L.H. Wrap Spring Wrench) (Shown) GD Torsion Spring, L.H. (Used In R.H. Wrap Spring Wrench) 30. GD Handle 31. G Hex Socket Button Head Screw, ¼"-20 x ½", Grade 8 G Lock Washer, ¼" G Washer, ¼" USS 32. GD Sleeve, 1 ¼" O.D. x ⅝" Long 33. G Internal Inverted Snap Ring, ⅞" 34. G External Inverted Snap Ring, 1 ½" 35. GD Tightener Shaft, 4 ⅞" 36. G Vinyl Cap A. G1K269 - Lock Clamp Kit (Items 2 And 3) B. G1K379 - Wrap Spring Wrench Replacement Kit, Silver Collar, L.H. (Items 27-36) (Shown) G1K378 1 Wrap Spring Wrench Replacement Kit, Gold Collar, R.H. (Items 27-36) P147 Rev. 8/07

148 LIQUID FERTILIZER SQUEEZE PUMP, 8 ROW SIZE LFC011(PT46a) 1. GR Spring Anchor Bar 2. GR Spring 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Washer, 5 16" USS G Wing Nut, 5 16" GR Plate 5. GR Nylon Bushing 6. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Wing Nut, 5 16" GR Metering Hose, ½" x 13" 8. G Hose Clamp, No G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Hex Nut, ⅜" GR Angle 11. GR Manifold Plug 12. GR Adapter 13. GR Intake Manifold 14. GR Discharge Manifold Less Hose Barbs 15. G Hose, ⅜" x 120' 16. GR Rubber Cap 17. GR Nylon Washer 18. G Square Head Set Screw, 5 16"-18 x ¾" 19. G Grease Fitting, ¼" GR Roller Arm 21. GR Roller 22. G Spring Pin, 5 16" x 1 ⅛" 23. GD Sleeve 24. GD Shaft 25. GR Shim, 3 64" 26. GR Shim, 1 32" 27. GR Frame 28. GR Nylon Hose Barb, ½" x ⅜" (If Applicable) A. GA Squeeze Pump Complete, 4 Rows (Items 1-14, And 24-28) P148 Rev. 8/07

149 LIQUID FERTILIZER SQUEEZE PUMP, 12 ROW SIZES LFC011/LFC011(PT47a) 1. GR Spring Anchor Bar 2. GR Spring 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Washer, 5 16" USS G Wing Nut, 5 16" GR Plate 5. GR Nylon Bushing 6. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Wing Nut, 5 16" GR Metering Hose, ½" x 13" 8. G Hose Clamp, No G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Hex Nut, ⅜" GR Angle 11. GR Manifold Plug 12. GR Adapter 13. GR Intake Manifold 14. GR Discharge Manifold Less Hose Barbs 15. G Hose, ⅜" x 160', 12 Row 30" G Hose, ⅜" x 120', 12 Row 36"/38" 16. GR Rubber Cap 17. GR Nylon Washer 18. GR Bushing 19. G Square Head Set Screw, 5 16"-18 x ¾" 20. G Grease Fitting, ¼" GR Roller Arm 22. GR Roller 23. G Spring Pin, 5 16" x 1 ⅛" 24. GD Sleeve 25. GD Shaft 26. GR Shim, 3 64" 27. GR Shim, 1 32" 28. GR Frame 29. GR Nylon Hose Barb, ½" x ⅜" (If Applicable) A. GA Squeeze Pump Complete, 6 Rows (Items 1-13, And 25-29) P149 Rev. 8/07

150 LIQUID FERTILIZER SQUEEZE PUMP, 16 ROW SIZE LFC010(PT48a) P150 Rev. 8/07

151 LIQUID FERTILIZER SQUEEZE PUMP, 16 ROW SIZE 1. GR Spring Anchor Bar 2. GR Spring 3. G Square Head Machine Bolt, 5 16"-18 x 1 ¾" G Washer, 5 16" USS G Wing Nut, 5 16" GR Plate 5. GR Nylon Bushing 6. G Carriage Bolt, 5 16"-18 x 1" G Washer, 5 16" USS G Wing Nut, 5 16" GR Metering Hose, ½" x 13" 8. G Hose Clamp, No GR Adapter 10. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Hex Nut, ⅜" GR Angle, L.H. GR Angle, R.H 12. GR Manifold Plug 13. GR Intake Manifold 14. GR Discharge Manifold Less Hose Barbs 15. G Hose, ⅜" x 120' 16. GR Rubber Cap 17. GR Nylon Washer 18. GR Bushing 19. G Square Head Set Screw, 5 16"-18 x ¾" 20. G Grease Fitting, ¼" GR Roller Arm 22. GR Roller 23. GR Set Collar 24. GR Back Up Roller 25. G Spring Pin, 5 16" x 1 ⅛" 26. GD Sleeve 27. GD Shaft 28. GR Shim, 3 64" 29. GR Shim, 1 32" 30. GR Frame 31. GR Nylon Hose Barb, ½" x ⅜" (If Applicable) A. GA Squeeze Pump Complete, 8 Rows (Items 1-14, And 27-31) P151 Rev. 8/07

152 REAR TRAILER HITCH PHA032/LFC003(TWL47a) P152 Rev. 8/07

153 REAR TRAILER HITCH 1. GA Hitch 2. G Hex Head Cap Screw, ⅝"-11 x 1 ½" GD Special Washer, ⅝", Hardened G Lock Washer, ⅝" 3. G Washer, 1 ¼" SAE 4. GD Pin, 1 ¼" x 12 ¾" G Cotter Pin, ¼" x 2" 5. GA Hitch 6. GB Bushing, 21 32" I.D. x ⅞" O.D. x 19 32" Long 7. GD Tap Block 8. GB Spring Seat 9. GD Spring 10. GB Rod Guide 11. GD Special Bolt G Hex Nut, ¾" G Hex Head Cap Screw, 1"-8 x 2 ½" G Lock Nut, 1" GD U-Bolt, 2" x 2" x ½"-13 G Lock Washer, ½" G Hex Nut, ½" GD Hanger Tube 15. GD Spring 16. G Twin Loop Chain, 15 Links 17. GA Hose Support 18. G Hex Head Cap Screw, ¼"-20 x 1" G Washer, ¼" USS G Lock Nut, ¼"-20, Grade B 19. GA Hose Support 20. G Hex Head Cap Screw, ⅜"-16 x 1 ¼" G Lock Nut, ⅜" G Hose, 1 ¼" x 22' 22. G Hose Clamp, No G Adapter, 1 ¼" NPT To Barb 24. GA Shutoff Valve, 1 ¼" NPT GR Body O-Ring GR Stem O-Ring GR Teflon Seat GR Ball GR Handle 25. GD Adapter, 1 ¼" Male NPT To Cam Lock 26. GD Dust Cap, 1 ¼" Cam Lock 27. GD Adapter, 1 ¼" Barb To Female Cam Lock 28. GD Dust Plug, 1 ¼" Male Cam Lock 29. G Hex Head Cap Screw, ⅜"-16 x 5" G Lock Washer, ⅜" G Hex Nut, ⅜" G Hex Head Cap Screw, ⅜"-16 x 6" G Lock Washer, ⅜" G Hex Nut, ⅜"-16 P153 Rev. 8/07

154 DECALS, PAINT AND MISCELLANEOUS Connect directly to DO NOT REMOVE THIS ASSEMBLY AFTER PLANTER IS ASSEMBLED FOR USE. REMOVAL OF THIS WHEEL AND AXLE ASSEMBLY CAN CAUSE THE MACHINE TO BECOME UNSTABLE AND TIP OVER CAUSING DAMAGE OR SERIOUS INJURY NOTE It is the responsibility of the user to read and understand the Operator s Manual in regards to safety, operation, lubrication and maintenance before operation of this equipment. AN OPERATOR & PARTS MANUAL IS AVAILABLE FOR THIS MACHINE. To obtain a manual, furnish model number and serial number and contact your KINZE Dealer or KINZE Manufacturing, Inc., P.O. Box 806 Williamsburg, IA USA P154 Rev. 8/07

155 DECALS, PAINT AND MISCELLANEOUS A A 9 P155 Rev. 8/07