Row Unit Operation. Eccentric bushing

Transcription

1 Row Unit 006 and on Row Unit Operation Planting Depth Planting depth is maintained by adjustable row unit gauge wheels. Depth adjustment range is approximately ½" to 3½".. Raise planter to remove weight from wheels.. Push down on depth adjustment handle and reposition it forward to decrease or rearward to increase planting depth. Initially adjust all units to the same setting. 3. Lower planter and check operation and planting depth of all row units. Readjust individual rows as needed for uniform operation. Planting depth adjustment handle Deeper Shallower Planting depth adjustment V Closing Wheel Adjustment (Rubber or Cast Iron) Down pressure adjustment lever Eccentric bushing Set closing wheels in forward hole for directly opposite installation. Increase Decrease Eccentric bushing V Closing wheel adjustments V closing wheels should have enough down pressure to close the seed trench and ensure good soil to seed contact. Move 5-position quick adjustable down force lever on the top of closing wheel arm to the rear to increase closing wheel spring pressure. Move lever forward to decrease pressure. Adjust all row units to a similar setting. Light soil usually requires less down force at average depth (approximately ") while heavy soil requires increased down force. Eccentric bushings in the wheel arm stop allow for lateral adjustment of the V closing wheel assembly. Use a ¾" wrench to loosen hardware attaching closing wheel arm to wheel arm stop. Use another ¾" wrench to turn eccentric bushings until closing wheels are aligned with seed trench. Tighten hardware. Closing wheels can be installed offset (to improve residue flow) or directly opposite. Use forward installation holes If set directly opposite. Closing Wheel Shield (Rubber or Cast Iron V Closing Wheels) Optional closing wheel shield is installed on underside of closing wheel arm to help prevent root balls and stalks from clogging closing wheels. Closing wheel shield (Closing wheel removed) Rev. 9/

2 Row Unit Operation Row Unit 006 and on Drag Closing Attachment Drag closing attachment pulls loose soil over seed trench. NOTE: Use of a seed firming wheel or other seed firming device is recommended with drag closing attachment. Eccentric bushing Front and rear adjustment is made using slotted holes in blades. Adjust all rows the same. Wheel arm stop eccentric bushings provide lateral adjustment. Use a ¾" wrench to loosen closing wheel arm to wheel arm stop hardware. Use another ¾" wrench to turn eccentric bushings until drag closing attachment is aligned with seed trench. Tighten hardware. Covering Discs/Single Press Wheel Adjustment Adjustment slots Blade Drag closing attachment Adjusting bolt ½" Tab ½" Locking nut Press wheel down force adjustment Check operation of covering discs/single press wheels after adjusting planting depth. Initial press wheel down force spring setting is ½" between mounting arm tab and locking nut. Loosen ½" locking nut and turn adjusting bolt in to increase down force or out to decrease down force. Tighten locking nut against spring plug. Adjust all row units to a similar setting. Locate for staggered or side-by-side operation Blade depth adjustment Wheel arm stop Blade angle adjustment Eccentric bushing Covering disc adjustments Eccentric bushings in the wheel arm stop allow for lateral adjustment of covering discs/single press wheel assembly. Use a ¾" wrench to loosen hardware attaching closing wheel arm to wheel arm stop. Use another ¾" wrench to turn eccentric bushings until covering discs/single press wheel assembly is aligned with seed trench. Tighten hardware. Two sets of holes in mounting arm locate covering discs for staggered or side-by-side operation. Five sets of holes in each disc bracket allow ½" incremental blade depth adjustment. Slotted holes in disc mount and bracket allow for 0-5 blade angle adjustment. Adjust covering discs on all row units to similar settings. Rev. 9/

3 Row Unit 006 and on Row Unit Operation Seed Hoppers Mechanical seed hopper has a capacity of.9 bushels. EdgeVac seed hopper has a capacity of.75 bushels. Use clean seed and make certain there are no foreign objects inside when filling seed hopper. Replace hopper lids after hoppers are filled to prevent accumulation of dust or dirt in seed meter which can cause premature wear. See Finger Pickup Seed Meter and/or Brush-Type Seed Meter. Periodically empty hoppers completely to remove any foreign objects and to ensure proper seed meter operation. Mechanical seed hopper Disengage meter drive and hopper latch and lift hopper off hopper support. See Seed Meter Drive Release. Seed Meter Drive Release A clutch release mechanism disengages seed meter drive from seed meter to remove seed hopper. Disconnecting drive allows operator to check granular chemical application rates without dropping seed. It also allows one or more rows to be disconnected when finishing fields. Disengage Turn knob ¼ turn counterclockwise to disengage or ¼ turn clockwise to engage. Engage Seed meter drive release Row Unit Extension Brackets Row unit extension brackets extend row units rearward 4" to provide clearance for coulter mounted residue wheels and HD single disc fertilizer openers. Extension bracket Extension bracket Row unit extension brackets Rev. 9/ 3

4 Row Unit Operation Row Unit 006 and on Row Unit Chain Routing Row unit drive chains must be properly tensioned and aligned for proper operation and to minimize wear. Inspect and replace weak, worn or broken springs, idlers, and idler bushings. Mechanical pull row unit meter drive EdgeVac pull row unit meter drive Mechanical push row unit meter drive EdgeVac push row unit meter drive Direction of travel Closed end NOTE: Install connector link with closed end facing direction of travel. Row unit granular chemical drive NOTE: Reverse idler when worn on one side for extended use. 4 Rev. 9/

5 Row Unit 006 and on Row Unit Operation Quick Adjustable Down Force Springs Option (Standard or Heavy Duty) Standard and heavy duty quick adjustable down force springs are available in increase penetration in hard soil and keep row unit from bouncing in rough field conditions. Two springs per row, one on each side parallel arms, are used unless equipped with row unit mounted no till coulters. Row unit mounted no till coulters require four springs per row. Two springs per row (Dual) Four springs per row (Quad) Pin Pin Pin Pin Position (Least) Position Position 3 Position 4 (Most) There are four positions to set down pressure spring tension. Position Standard and Heavy Duty Spring Down Force Pressure* Standard D849 Springs 4 Springs Heavy Duty D337 Standard D849 Heavy Duty D337 4lb (8.6 kg) 43 lb (9.5 kg) 74 lb (33.6 kg) 80 lb (36.3 kg) 73 lb (33. kg) 86 lb (39.0 kg) 0 lb (54.4 kg) 44 lb (65.3 kg) 3 36 lb (6.7 kg) 67 lb (75.7 kg) 55 lb (5.7 kg) 307 lb (39.3 kg) 4 07 lb (93.9 kg) 49 lb (3.0 kg) 369 lb (67.4 kg) 470 lb (3. kg) *Pressure does not include weight of row unit, seed, or options. NOTICE Springs must be installed with open side of spring hooks toward seed hoppers to prevent binding on spring mount adjustment pins.. Raise planter and remove spring mount pin at top of spring.. Slide mount to desired position and install pin. NOTE: Adjust springs for field conditions. Too much down pressure in hard field conditions can cause row units to lift planter and keep drive wheels from making contact. Too much down pressure in soft field conditions can cause row unit to run too deep. Rev. 9/ 5

6 Row Unit Operation Row Unit 006 and on PNEUMATIC DOWN PRESSURE PACKAGE OPTION Row unit down pressure can be adjusted on-the-go as field conditions change with pneumatic down pressure option. A cab-mounted control box adjusts pressure (Older models may have a digital readout). A planter-mounted VDC air compressor with 3 gallon capacity air tank supplies air for the down pressure system. Packages include upper and lower air spring mounting castings for pull row units (front and rear air spring mounting castings for push row units), 50 psi rated air springs, ⅜" O.D. nylon hoses, dual solenoid air valve and stainless steel, 60 psi, " liquid-filled gauge and planter wiring harness. Pneumatic down pressure row unit extension brackets are required in some applications. Pull row unit air spring Push row unit air spring NOTE: If additional down pressure is needed with the Pneumatic Down Pressure Package, assist springs are available through your Kinze dealer. One spring is installed on the outer side of the parallel arms on each side of the row unit as shown below. Pull row unit assist springs Push row unit assist springs 6 Rev. 9/

7 Row Unit 006 and on Row Unit Operation FIELD OPERATION NOTE: Adjust down pressure with planter lowered and row openers in ground for most accurate adjustment. Pressure can be adjusted from tractor using control console, or at planter using manual control valves on compressor assembly. Pressure gauge Shutoff valve Increase pressure Decrease pressure Control console Air compressor assembly controls ADJUST DOWN PRESSURE FROM CAB Push toggle switch left to increase or right to decrease pressure. ADJUST DOWN PRESSURE AT PLANTER Push and hold decrease or increase button on compressor assembly to decrease or increase pressure. NOTE: Value on the air pressure gauge is NOT down pressure force. Multiply air pressure (psi) by four (4) to calculate down pressure. LOCK UP PUSH ROW UNITS EQUIPPED WITH PNEUMATIC DOWN PRESSURE SPRINGS. Press and hold button on solenoid until pressure gauge reads 5 PSI.. Lock up units. See Interplant Push Unit Lockup for instructions. 3. Turn shutoff valve handle perpendicular to valve body to turn off push row unit air supply. Interplant Push Row Unit Clutch Sprocket Push row unit clutch sprocket disengages interplant drive from push row unit drill shaft when only pull row units are used. DISENGAGE Rotate knurled collar ¼ turn. Rock drill shaft slightly using a ⅞" wrench to take pressure off of spring loaded pins in clutch to allow pins to pop out, disengaging drive. ENGAGE Rotate knurled collar ¼ turn and turn drill shaft with a ⅞" wrench until drive pins engage drive sprocket. Interplant clutch sprocket Rev. 9/ 7

8 Row Unit Operation Row Unit 006 and on Interplant Push Row Unit Lockups Push row unit lockups lock interplant row units in the raised position. CAUTION Improper lifting of row units can cause serious injury. An empty row unit requires minimum 90 lb (40.8 kg) lift. Set down pressure springs to minimum, lower planter to ground, and empty seed hopper before attempting to lift with this lever. Lift lever positioned on push row unit Lift lever in storage location Lockup released for field operation Push row unit locked in raised position Interplant Push Row Unit Vacuum Hose Shutoff Storage mount Interplant vacuum hose shutoff When push row units are not used, move row unit end of " vacuum hose on each push row unit to storage mount located on side of shank. 8 Rev. 9/ TM

9 Row Unit 006 and on Row Unit Operation Frame Mounted Coulter (Pull Row Only) Frame mounted coulters with " bubbled, " fluted (8 flutes) or ¾" fluted (3 flutes) blades are used on pull row units only. Spring adjustment bolt Spring anchor bar Springs provide down pressure on coulter for maximum penetration while exerting less shock load on row unit. Initial coulter blade location is in top hole. Relocate blade to one of lower two holes (" increments) as wear occurs or for deeper blade operation. Blade depth adjustment holes Frame mounted coulter adjustment DOWN PRESSURE ADJUSTMENT NOTICE Excessive down pressure can damage coulter components when coulter strikes an obstacle. Do not set down pressure higher than needed for consistent soil penetration. Raise planter. Turn spring adjustment bolts clockwise to increase or counterclockwise to decrease down pressure. Set both springs to specification shown in following table: Frame Mounted Coulter Spring Downpressure Settings End flush with spring Extended ½" through All threads used anchor bar spring anchor bar 75 lb (4.7 kg) 400 lb (8.4 kg) 500 lb (6.8 kg) Residue Wheels (for Frame Mounted Coulter) NOTE: Opening in weed guard must face down. NOTICE Tined wheel forward mounting positions cannot be used behind 3600 axles due to limited cklearance. Residue wheels attach to frame mounted coulter with two cap screws and sleeves allowing the unit to free-float. A -position spindle bolt mounting positions wheels interlocked or staggered. Depth adjustment is made with a springloaded cam and pin with positions in ¼" increments. A high point on the cam allows wheels to be locked up. A weed guard on the inboard side of each wheel helps prevent weed wrap which can cause premature bearing failure. Rev. 9/ 9

10 Row Unit Operation Row Unit 006 and on Row Unit Mounted Disc Furrower (Pull Row Only) Disc furrowers are used to clear crop residue, dirt clods, and dry soil from in front of row units for a clean and smooth seed bed. The disc furrower may be equipped with " solid blades or " notched blades. Notched blades are for heavier residue conditions and cut crop residue and move it aside to prevent plugging or pushing. Set screw Lynch pin Dust cap Slotted holes Disc furrower adjustment Vertical adjustment can be made in ⅓" increments. Remove lynch pin in vertical support arm and move arm up or down. Reinstall lynch pin. Finer adjustment can be made by removing lynch pin and using ⅝" x ¼" set screw to clamp support arm in position. Slotted holes in support arm allow front to rear disc blade adjustment. Blades can be adjusted so front edges meet or cutting edge of one blade overlaps edge of other blade. NOTE: Dust cap must be removed to make adjustments. Row Unit Mounted Bed Leveler (Pull Row Only) NOTE: Row unit mounted bed leveler is not compatible with row spacings less than 36". Vertical adjustment can be made in ⅓" increments. Remove lynch pin in vertical support arm and move arm up or down. Reinstall lynch pin. Finer adjustment can be made by removing lynch pin and using ⅝" x ¼" set screw to clamp support arm in position. Slotted holes in support arm allow blade adjustment. Blades can be tilted up or down. Set screw Slotted holes behind blades in support arm. Lynch pin Bed leveler adjustment 0 Rev. 9/

11 Row Unit 006 and on Row Unit Operation Row Unit Mounted Residue Wheel Row unit mounted residue wheels are used on pull and push row units. Row Unit Mounted Residue Wheel Two adjustable springs on each residue wheel parallel links provide down force adjustment. Position provides minimum down pressure and position 3 maximum down pressure. Position (Least) Position Position 3 (Most) Additional uplift or float Raise row unit and reposition springs to adjust down pressure. Depth adjustment Least aggressive Most aggressive Lock up bolt Wheel depth adjustment Wheel angle adjustment Wheel lock up A full threaded bolt and jam nut located on the upper link sets maximum depth for loose soil conditions. Initial setting is ¾" above row unit double disc opener depth. Three holes in upper link adjust wheel angle. With wheel mount in most vertical position, using the rear hole in the upper link, the residue wheel is most aggressive. Moving wheel mount to a forward hole reduces aggressiveness of residue wheel for use in mulch till applications where soil is loose. To lock residue wheel up, remove ½" x 5" lockup bolt, raise residue wheel and install bolt. Rev. 9/

12 Row Unit Operation Row Unit 006 and on Row Unit Mounted No Till Coulter Row unit mounted no till coulters with " bubbled, " fluted (8 flutes) or ¾" fluted (3 flutes) blades may be used on pull row units and push row units (¾" fluted shown). Four quick adjustable down force springs are required per row when using row unit mounted no till coulters. See Quick Adjustable Down Force Springs Options. Align coulter blade to row unit double disc openers. Adjust by loosening four attaching bolts, moving coulter arm, and tightening four attaching bolts. Coulter blade can be adjusted to one of four ½" incremental settings in the forked arm. Initial location is the top hole. Blade adjustment holes. Row Unit Mounted No Till Coulter Move blade as it wears to one of the three lower hole to maintain coulter blade at or slightly below opener discs. Adjust coulter below depth of double disc opener blades in very hard soil conditions such as compacted wheel tracks to improve opener penetration and cutting of surface residue. Check operating depth by setting planter down on a level concrete floor and checking relationship between coulter blade and row unit opener blade. Make sure planter is level and coulter is square with planter frame and aligned with row unit disc opener. NOTE: Torque ⅝" spindle hardware to 0 ft-lb (6.7 N-m). Coulter Mounted Residue Wheels Coulter mounted residue wheels are designed for use on pull row units and push row units. Row unit extension brackets are required on the four center pull row units if the planter is equipped with coulter mounted residue wheels. Weed guard NOTE: Opening in weed guard must face down. Coulter mounted residue wheels Residue wheels attach to row unit mounted coulter with two cap screws and sleeves allowing unit to free-float. A -position spindle bolt mounting positions wheels interlocked or staggered. Depth adjustment is made with a springloaded cam and pin with positions in ¼" increments. A high point on the cam allows wheels to be locked up. A weed guard on the inboard side of each wheel helps prevent weed wrap which can cause premature bearing failure. Rev. 9/

13 Row Unit 006 and on Row Unit Operation Granular Chemical Hopper and Drive WARNING Agricultural chemicals can cause death or serious injury to persons, animals, and plants or seriously damage soil, equipment, or property. Read and follow all chemical and equipment manufacturers labels and instructions. The granular chemical hopper has a.4 cubic feet capacity. Make sure no foreign objects get into hopper when it is being filled. Replace hopper lids after filling to prevent accumulation of dirt and moisture. A metering gate on bottom of hopper regulates the application rate. See Dry Insecticide and Dry Herbicide Application Rate Charts in this manual. Calibrate using chemical manufacturers instructions. Granular chemical hopper Granular chemical clutch drive coupler and meter shaft can be disengaged and engaged by turning throwout knob at rear of hopper support panel. Disengage Rotate knob ¼ turn counterclockwise to disengage and ¼ turn clockwise to engage. Slotted holes in hopper support panel and clutch housing allow for alignment adjustment between clutch drive coupler and meter shaft. Engage Granular chemical drive release Spring Tooth Incorporator Spring tooth incorporator smooths soil behind row unit and incorporates granular chemicals. Adjust two mounting chains on each spring tooth incorporator so there is approximately ⅛" slack in chain when unit is lowered to planting position. NOTE: Spring tooth incorporator is not compatible with covering discs/single press wheel option. Spring tooth incorporator Rev. 9/ 3

14 Row Unit Operation Row Unit 006 and on Granular Chemical Banding Options Granular chemical banding options allow 4½" slope-compensating banding, straight drop in-furrow placement or 4" rear banding. NOTE: Granular chemical rear bander is not compatible with covering discs/single press wheel option. 4" rear banding 4½" slope-compensating bander Straight drop in-furrow placement Granular Chemical Bander Shield Bander shield Wheel arm stop ⅜"-6 x ½" hex head cap screw Optional granular chemical bander shield is installed on underside of wheel arm stop to shield crop residue from lodging in granular chemical bander. Hardened washer Granular chemical bander shield installation 4 Rev. 9/

15 Row Unit 006 and on Lubrication and Maintenance Chain Tension Adjustment Drive chains have spring loaded idlers and are self-adjusting. Remove link to shorten chain if wear stretches chain and reduces spring tension. Check idler pivot points to make sure they rotate freely. See Wrap Spring Wrench Assembly in this section for additional information. Additional chain links are stored inside planter frame. Additional chain links Drag Closing Attachment Inspect each drag closing attachment and replace any worn or broken parts before storing planter. Check for loose hardware and tighten as needed. Drag Closing Attachment Gauge Wheel Adjustment Machine bushings Shim gauge wheel to lightly contact opener disc blade. Check adjustment in field position. Gauge wheel adjustment Gauge wheels should lightly contact opener blades to prevent accumulation of dirt or trash. Gauge wheels and opener blades should turn with only slight resistance. Add or remove machine bushings between shank and gauge wheel arm to adjust clearance between gauge wheels and opener blades. Store remaining machine bushings between gauge wheel arm and flat washer on outer side of gauge wheel arm. NOTE: It may be desirable to space gauge wheel further from blade when operating in sticky soils. Rev. 9/ 5

16 Lubrication and Maintenance Row Unit 006 and on Gauge Wheel Arm Bushing/Seal Replacement Gauge wheel arm bushings/seals Seal Seal Bushing Bushing NOTE: Gauge Wheel Arm Bushing and Seal Driver Kit (GK96) is available through your Kinze Dealer.. Remove gauge wheel from arm.. Remove gauge wheel arm from shank assembly. 3. Remove seal and bushing and discard. Clean and dry inner bore. 4. Drive/press replacement bushing inside bore of arm to a depth of.5" below flush. 5. Coat wiping edge of seal with grease. 6. Drive/press seal into place with lip to outside. NOTE: Use extra care to protect the sealing lip during installation. Apply uniform pressure to assemble the seal into the bore of the arm. Never apply a direct hammer blow to the seal surface. 7. Inspect gauge wheel pivot spindle. 8. Reinstall gauge wheel arm assembly and gauge wheel. NOTE: Use special machine bushing between gauge wheel arm and gauge wheel. 9. Shim for proper gauge wheel tire/disc blade clearance. 0. Lubricate with an SAE multipurpose grease. Gauge Wheel Arm Pivot Spindle Replacement. Remove gauge wheel and arm assemblies from shank assembly. Pivot spindle cap screw. Remove ½" x ¾" cap screw that locks pivot spindle in place and remove spindle. 3. Install replacement spindle and position as shown. Exact centering is critical. ⅞" 4. Install ½" x ¾" cap screw and torque to lock pivot spindle in place. 5. Install gauge wheel and arm assemblies. Shim for proper gauge wheel tire/disc blade clearance. 6 Rev. 9/

17 Row Unit 006 and on Lubrication and Maintenance 5" Seed Opener Disc Blade/Bearing Assembly NOTICE Excessive blade contact may result in premature disc opener bearing/hub failures and excessive wear on seed tube guard/inner scraper. When properly adjusted, if one blade is held in fixed position, opposite blade should rotate with less than 5 pounds force at outer edge of blade. Maintain approximately " - ½" of blade-to-blade contact to properly open and form seed trench. As blade diameter decreases due to wear, it is necessary to relocate machine bushings from inside to outside to maintain " - ½" of contact. Approximately " - ½" blade-to-blade contact. NOTE: Replace blades If proper blade-to-blade contact cannot be maintained after relocating machine bushings or if blade diameter wears below 4½". REPLACE DISC BLADE/BEARING ASSEMBLY NOTE: Only bearing may need to be replaced if there is excessive endplay or if bearing sounds or feels rough when disc blade is rotated.. Remove gauge wheel, scraper, and bearing dust cap.. Remove cap screw, washer and disc blade/bearing assembly. Machine bushings between shank and disc blade are used to maintain approximate " - ½" of blade-to-blade contact. NOTICE Left hand side of opener uses a left hand threaded cap screw. DO NOT OVER TIGHTEN. Damage to shank threads require replacement of row unit shank assembly. 3. Install machine bushing(s), new disc blade bearing assembly, washer and cap screw. Torque ⅝"- Grade 5 cap screw to 0 ft-lb (49.4 N-m). NOTE: Replace disc blades only with disc blades of equal thickness. 4. Install bearing dust cap, scraper, and gauge wheel. REPLACE BEARING ONLY. Remove gauge wheel, scraper, bearing cap, cap screw, washer and disc blade/bearing assembly.. Remove ¼" rivets from bearing housing to expose bearing. 3. Installing new bearing. install three evenly spaced ¼" cap screws into three of six holes in bearing housing to hold bearing and bearing housing in place. Install rivets in other three holes. Remove ¼" cap screws and install rivets in those three holes. 4. Reinstall disc blade/bearing assembly, washer and cap screw. Torque ⅝"- cap screw to 0 ft-lb (49.4 N-m). 5. Install bearing dust cap, scraper, and gauge wheel. Rev. 9/ 7

18 Lubrication and Maintenance Row Unit 006 and on Seed Tube Guard/Inner Scraper Seed tube guard protects seed tube and acts as inner scraper for seed opener disc blades. Remove seed tube and check for wear. Excessive wear on seed tube indicates a worn seed tube guard. Replace seed tube guard if it measures ⅝" or less at lower end. A new seed tube guard measures approximately ⅞". NOTE: No till planting or planting in hard ground conditions, especially when planter is not equipped with no till coulters, and/or excessive blade-to-blade contact increases seed tube guard wear and requires more frequent inspection and/or replacement. NOTICE Over tightening hex socket head cap screws may damage shank threads and require replacement of shank. An excessively worn seed tube guard may allow blades to wear into row unit shank, also requiring replacement of shank. Remove seed tube and two hex socket head cap screws that attach seed tube guard. Hold replacement seed tube guard centered between seed opener disc blades. Install hex socket head cap screws. DO NOT TIGHTEN. Using a clamp or vise-grip, squeeze opener blades together in front of seed tube guard. Tighten seed tube guard retaining screws. Remove clamps. Distance between seed tube guard and opener blades should be equal on both sides. Reinstall seed tube. Frame Mounted Coulter Seed tube guard/inner scraper (Gauge wheel/seed opener disc blade removed NOTE: Torque ⅝" spindle hardware to 0 ft-lb (6.7 N-m) See Frame Mounted Coulter in Row Unit Operation section of this manual for depth and spring adjustment. Replace 6" diameter coulter blade (" fluted, " bubbled or ¾" fluted) when worn to 4½" (maximum allowable wear). Residue Wheels (For Use With Frame Mounted Coulter) Wheel hub is equipped with sealed bearings. Replace bearings if a bearing sounds or feels rough when wheel is rotated. Frame mounted coulter spindle Frame mounted coulter residue wheels 8 Rev. 9/

19 Row Unit 006 and on Lubrication and Maintenance Row Unit Mounted Disc Furrower Lubricate bushings in support arm mounting bracket at frequency indicated in Lubrication of this section. Check each bolt for proper torque. If bolt is loose, it should be removed and bushing inspected for cracks and wear. Replace bushings as necessary. NOTE: Use only hardened flat washers. Replace damaged flat washers with proper part. Torque bolts to 30 ft-lb (76. N-m). Blade hubs are equipped with sealed bearings. Replace bearings if a bearing sounds or feels rough when wheel is rotated. Row unit mounted disc furrower Replace solid or notched " diameter blades when worn to ". Row Unit Mounted Bed Leveler Lubricate bushings in mounting bracket and links at frequency indicated in Lubrication of this section. Check each bolt for proper torque. If bolt is loose, it should be removed and bushing inspected for cracks and wear. Replace bushing if necessary. NOTE: Use only hardened flat washers. Replace damaged flat washers with proper part. Torque bolts to 30 ft-lb (76. N-m). Row unit mounted bed leveler Row Unit Mounted No Till Coulter Check nuts and hardware periodically for proper torque. Be sure coulter is positioned square with row unit and aligned in front of row unit disc opener. NOTE: Torque ⅝" spindle hardware to 0 ft-lb (6 N-m). Coulter blade can be adjusted to one of four settings. Initially blade is set in highest position. As blade wears it can be adjusted to one of three lower settings. See Row Unit Mounted No Till Coulter in Row Unit Operation section of this manual. Replace 6" diameter coulter blade when worn to 4½". Row unit mounted no till coulter Rev. 9/ 9

20 Lubrication and Maintenance Row Unit 006 and on Coulter Mounted Residue Wheels Wheel hubs are equipped with sealed bearings. If bearings sound or feel rough when wheel is rotated, replace them. Coulter mounted residue wheels Row Unit Mounted Residue Wheel Wheel hub is equipped with sealed bearings. If a bearing sounds or feels rough when wheel is rotated, replace them. Granular Chemical Attachment Before storing planter, disengage granular chemical drive by rotating throwout knob ¼ turn counterclockwise. Remove drive chain and empty and clean all granular chemical hoppers. Clean drive chains and coat them with a rust preventive spray or submerge chains in oil. Inspect and replace worn or broken parts. Install hoppers and chains. Check chain alignment. Row unit mounted residue wheels Disengage Engage Spring Tooth Incorporator Before storing planter, inspect each spring tooth incorporator and replace worn or broken parts. Check for loose hardware and tighten as needed. Granular chemical throwout knob Spring tooth incorporator 0 Rev. 9/

21 Row Unit 006 and on Lubrication and Maintenance Air Clutch Cleaning (Yearly at end of planting season) NOTE: If system is equipped with Pneumatic Down Pressure, air clutches must be removed from planter for cleaning. If system is not equipped with Pneumatic Down Pressure, air clutches can be disassembled and cleaned on planter. At each row unit:. Remove meter assembly.. Press down collar on air fitting and remove air hose. 3. Loosen tension from chain and remove from air clutch sprocket. 4. Loosen lock clamp and slide clamp, washer, and air clutch away from chain. 5. Use a 5 6" wrench and remove sprocket from air clutch assembly. 6. Remove small Phillips-head screw from side of air clutch housing and remove housing cover. 7. Expand retaining ring and remove from assembly. 8. Remove and separate sprocket hub, ratchet gear, clutch spring, and hex bushing from air clutch housing. 9. Remove debris and dirt from clutch components. Clean parts with brake cleaner or equivalent cleaner. 0. Make sure parts are completely dry. Lubricate sprocket hub, ratchet gear, clutch spring, and hex bushing with silicone spray.. Reverse procedure to assemble air clutch assembly.. Place one drop of pneumatic or light-duty hydraulic oil in air cylinder fitting before attaching air line. 3. Install meter assembly. Rev. 9/

22 Troubleshooting Row Unit 006 and on Air Clutch PROBLEM POSSIBLE CAUSE SOLUTION Clutches slip (effected row does not plant or skips). Plunger in cylinder seized. Worn Clutch. Dirt / debris buildup inside clutch. Remove air line and lubricated with pneumatic or light duty hydraulic oil. Replace worn items. Disassemble clean as needed. Reassemble. Closing Wheel PROBLEM POSSIBLE CAUSE SOLUTION Closing wheel(s) leave severe imprint in soil. Closing wheel(s) not firming soil around seed. V closing wheel running on top of seed furrow. Single closing wheel not directly over seed. Too much closing wheel down pressure. Not enough closing wheel down pressure. Improper centering. Improper centering. Adjust closing wheel pressure. Adjust closing wheel pressure. Severe no till conditions may require use of cast iron closing wheels. Align. See V Closing Wheel Adjustment. Align. See Covering Discs/Single Press Wheel Adjustment. Rev. 9/

23 This page left blank intentionally.

24 Shank Assembly, Seed Tube, and Depth Adjustment Row Unit 006 and on (IP74) Rev. 9/

25 Row Unit 006 and on Shank Assembly, Seed Tube, and Depth Adjustment ITEM PART NO. QTY. (Per Row) GD937 *G0003 *G008 GA3580 G98 G84 3 G036 G387 4 G G G DESCRIPTION GR096-5 GD96 Idler 6 GD06 Sleeve, 3 6" Long 7 G00 Special Washer, ⅜" x ½" O.D. 8 GD065 Idler Spring 9 GD738 Sleeve, " Long 0 GD645 Sun Shade (Rubber) GD845 Dust Cap GD0867 G0003 G008 3 G055 G G03 G060 Implement Switch Bracket Hex Head Cap Screw, ⅜"-6 x ½" Lock Nut, ⅜"-6 Limit Switch W/Cable Hex Slotted Head Cap Screw, #0-3 x " Serrated Flange Nut, #0-3 Hex Head Cap Screw, ⅜"-6 x 3¾" Flat Washer, ⅜" SAE Chain, No. 4, 98 Pitch Including Connector Link (Mechanical) Chain, No. 4, 08 Pitch Including Connector Link (EdgeVac) Chain, No. 4, 6 Pitch Including Connector Link (Used W/Row Unit Extension Brackets) Connector Link, No. 4 Stop Hex Head Cap Screw, ⅜"-6 x ½" Lock Nut, ⅜"-6 Clevis Pin, ¼" x ½" Hair Pin Clip, No. Carriage Bolt, 5 6"-8 x ¾" Serrated Flange Nut, 5 6"-8 5 GD033 Shield See Gauge Wheels on page See KPM III Electronic Seed Monitor on page <?> See Planter Monitor Module (PMM) on page <?> 8 G008 G007 Hex Head Cap Screw, ⅜"-4 x ½", Grade 8 Lock Nut, ⅜"-4, Grade C 9 GA057 Shank W/Gauge Wheel Pivot Spindle And Set Screw 0 G0438 Hex Head Cap Screw, ½"-3 x ¾" GB065 Pivot Link, Depth Adjustment GD00 Spindle 3 GD59 Sleeve, ⅜" I.D. x ⅝" O.D. x 5 3" Long 4 GB085 G007 Collar, Depth Adjustment Washer, ⅞" O.D. x 3 3" I.D. x.34" (If Applicable) 5 GD336 Pin, ⅜" x ⅔" 6 GB067 GD0993 Lever, Depth Adjustment Spring 7 GB066 GD36 Handle, Depth Adjustment Cap Plug 8 GB074 G05 Cover, Depth Adjustment Hex Washer Head Cap Screw, ⅜"-6 x ¼" 9 GD704 Hose Guide 30 G0047 G387 G008-3 Hex Head Cap Screw, ⅜"-6 x ¾" Flat Washer, ⅜" SAE Lock Nut, ⅜"-6 A GA Implement Switch Assembly, (Items -) *Items not included in Implement Switch Assembly Rev. 9/ 5

26 Pneumatic Down Pressure Package Option Row Unit 006 and on (RU57c/RU59a/RU57d/A405) Pull Row Unit Shown NOTE: Items that are not referenced on this page may be referenced on page Push Row Unit Shown Rev. 9/

27 Row Unit 006 and on Pneumatic Down Pressure Package Option ITEM PART NO. QTY. (Per Row) GA98 G0037 G08 GB0394 Saddle 3 G08 G39 GD DESCRIPTION 4 GB0396 Head Mount 5 GB0397 GD909 GD Air Spring Assembly Hex Head Cap Screw, ½"-3 x ¼" Lock Washer, ½" Hex Head Cap Screw, ⅝"-8 x ¼" Flat Washer, ⅝" SAE Sleeve, ⅞" O.D. x ⅝" I.D. x 3" Shoulder Nut, ¾"-6 Connector, ⅜" x ⅛" NPT Elbow, ⅜" x ⅛" NPT Extended (used on outer push units) 6 GB0395 Bracket 7 GA80 - Hanger Bearing, ⅞" Hex Bore 8 G0004 G387 GD G008 Hex Head Cap Screw, ⅜"-6 x ¼" Flat Washer, ⅜" SAE Spacer, ¼" Lock Nut, ⅜"-6 9 GD7794 Link (not applicable with row unit extension brackets) 0 GB0393 Plate G0037 G389 G08 GB0390 Yoke Mount 3 GB039 Yoke 4 GB039 Mount 5 G007 G389 G08 G00 6 GB0389 Plate 7 GB0398 Extension 8 G0039 G389 G Hex Head Cap Screw, ½"-3 x ¼" Flat Washer, ½" SAE (Lower Two Holes Only) Lock Washer, ½" Hex Head Cap Screw, ½"-3 x ½" Flat Washer, ½" SAE Lock Washer, ½" Hex Nut, ½"-3 Hex Head Cap Screw, ½"-3 x ¾" Flat Washer, ½" SAE Lock Nut, ½"-3 9 GD045 - Lock Clamp See Air Clutch, Pull Row Unit on page 8 G030 G Square Head Machine Bolt, 5 6"-8 x ¾" Flange Nut, 5 6"-8, No Serration Rev. 9/ 7

28 Air Clutch, Pull Row Unit Row Unit 006 and on (IP65) ITEM PART NO. QTY. DESCRIPTION (Per Row) GD889 Spacer, ¼" O.D. x " G39 3 Hex Head Cap Screw, 0-3 x ½" 3 GR83 Sprocket, 9 Tooth 4 G95 Retaining Ring 5 G43 Slotted Flat Head Machine Screw, No. 8-3 x ½", Stainless Steel 6 GR894 Air Housing Cover 7 GR89 Sprocket Hub 8 GR83 Clutch Spring 9 GR88 Ratchet Gear 0 GR830 Hex Bushing G003 Hex Head Cap Screw, ¼"-0 x ¾" G003 Hex Nut, ¼"-0 3 GR89 Push Connect, ⅛" NPT Male x ¼" 4 GR896 Air Cylinder 5 GR898 Filter 6 G96 Pan Head Machine Screw, ¼"-0 x ¾" x ¾" 7 GR895 Air Clutch Housing A GA405 - Air Clutch Assembly, (Items -7) 8 Rev. 9/

29 This page left blank intentionally.

30 Parallel Arms, Mounting Support Plate, and Quick Adjustable Down Forces Springs Option Row Unit 006 and on (IP77) Rev. 9/

31 Row Unit 006 and on Parallel Arms, Mounting Support Plate, and Quick Adjustable Down Forces Springs Option ITEM PART NO. QTY. (Per Row) GD3 G030 G DESCRIPTION U-Bolt, 5" x 7" x ⅝"- Lock Washer, ⅝" Hex Nut, ⅝"- GD0036 Mounting Support Plate 3 GB08 8 Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long 4 GD4 Upper Parallel Arm 5 G39 8 Flat Washer, ⅝" SAE 6 G073 G Hex Head Cap Screw, ⅝"-8 x " Lock Nut, ⅝"-8 7 GB086 Spring Anchor 8 GD47 Tab Lock Pin, 7 6" x ½" 9 GD849 GD337 0 G075 G Standard Down Pressure Spring Heavy Duty Down Pressure Spring Hex Head Cap Screw, ⅝"-8 x ¼" Lock Nut, ⅝"-8 GA565 Lower Parallel Arm G075 G04 Hex Head Cap Screw, ⅝"-8 x ¾" Lock Nut, ⅝"-8 3 GA70 Bearing/Sprocket, ⅞" Hex Bore 4 G0004 G09 5 G0007 G030 G Hex Head Cap Screw, ⅜"-6 x ¼" Serrated Flange Nut, ⅜"-6 Hex Head Cap Screw, ⅝"- x ½" Lock Washer, ⅝" Hex Nut, ⅝"- 6 GB0366 Extension Bracket A G635X - U-Bolt Package For 5" x 7" Toolbar, Includes: () GD3, (4) G030, (4) G004 Rev. 9/ 3

32 5" Seed Opener Disc Blade/Bearing Assembly and Scrapers Row Unit 006 and on (IP7) Rev. 9/

33 Row Unit 006 and on 5" Seed Opener Disc Blade/Bearing Assembly and Scrapers ITEM PART NO. QTY. DESCRIPTION (Per Row) See Shank Assembly, Seed Tube, and Depth Adjustment on page 4 G03 - Machine Bushing, ⅝" (.030" Thick)(As Required) 3 GD59 Sleeve, ⅜" I.D. x ⅝" O.D. x 5 3" Long 4 GA0R GA0L 5 G035 G06 6 G038 G06 - Disc Scraper, R.H. Disc Scraper, L.H. (Shown) Hex Head Cap Screw, ⅜"-6 x ¾" Serrated Flange Nut, ⅜"-6 Hex Head Cap Screw, ⅜"-6 x ⅝" Serrated Flange Nut, ⅜"-6 7 GD845 Dust Cap 8 GD07 Special Hex Head Cap Screw, ⅝"- x ½", L.H. Threads 9 G004 Special Machine Bushing, ⅝" x " O.D. 0 G047 Rivet, ¼" x ½" GD0473 Bearing Housing GA04 Bearing 3 GD306 Disc Blade, 3.5 mm x 5" 4 GB030 Seed Tube Guard/Inner Scraper 5 G09 Hex Socket Head Cap Screw, 5 6"-8 x ", Grade 8 A GA834 - Disc Blade/Bearing Assembly, Less Dust Cap (Items 0-3) Rev. 9/ 33

34 Gauge Wheels Row Unit 006 and on (IP68) Rev. 9/

35 Row Unit 006 and on Gauge Wheels ITEM PART NO. QTY. DESCRIPTION (Per Row) See Shank Assembly, Seed Tube, and Depth Adjustment on page 4 GA7975 GA7976 Wheel Arm W/Grease Fitting, Bushings And Seals, L.H. (Shown) (Includes Items 3 and 3) Wheel Arm W/Grease Fitting, Bushings And Seals, R.H. (Includes Items 3 and 3) 3 GB076 Bushing, " I.D. x ¼" O.D. x " Long (Per Arm) 4 G004 G08 G06 5 GD43 4 Half Wheel 6 GD086 Tire 7 GD453 Cover 8 G094 G060 9 G0338 G Hex Head Cap Screw, ½"-3 x " Lock Washer, ½" Washer, ½" USS Carriage Bolt, 5 6"-8 x ¾" Serrated Flange Nut, 5 6"-8 Carriage Bolt, 5 6"-8 x ¼" Serrated Flange Nut, 5 6"-8 0 G000 Hex Head Cap Screw, ⅝"- x 3" G008 G Hex Head Cap Screw, 5 6"-8 x ⅝" Lock Nut, 5 6"-8, Grade 8 GA67 Bearing 3 GD099 Seal (Per Arm) 4 G004 Special Machine Bushing, ⅝" x " O.D. 5 G0640 Grease Fitting, ¼"-8 (Per Arm) 6 G Machine Bushing, " (.048" Thick) A GA Gauge Wheel Complete (Items 5-9 And -) B GK96 - Gauge Wheel Arm Bushing And Seal Driver Kit, Includes: () Seal Driver, () Bushing Driver, () Instruction Rev. 9/ 35

36 Covering Discs/Single Press Wheel Row Unit 006 and on RUA054/RUB06(RU94d) 36 Rev. 9/

37 Row Unit 006 and on Covering Discs/Single Press Wheel ITEM PART NO. QTY. (Per Row) G000 G387 DESCRIPTION Hex Head Cap Screw, ⅜"-6 x " Flat Washer, ⅜" SAE GB068 Wheel Arm Stop 3 G080 G035 G00 4 GA054 Spring 5 GB039 Eccentric Bushing 6 G00 Hex Nut, ½"-3 7 G005 Adjusting Bolt, ½"-3 x 5" 8 GA669 Mounting Arm 9 G0463 Cotter Pin, ¼" x ½" 0 G07 G03 G006 GA660 Bracket GA668 Mount 3 G0303 G386 G03 G Carriage Bolt, ½"-3 x ¼" Carriage Bolt, ½"-3 x ½" (Used W/Straight Drop In-Furrow Granular Chemical Bracket) Hex Nut, ½"-3 Hex Head Cap Screw, 5 6"-8 x ¼" Lock Washer, 5 6" Hex Nut, 5 6"-8 Carriage Bolt, 5 6"-8 x " Flat Washer, 5 6" SAE Lock Washer, 5 6" Hex Nut, 5 6"-8 4 G007 3 Lock Nut, ⅝"- 5 GD09 Bushing, 4 64" I.D. x ⅞" O.D. x ¼" Long 6 GD990 Disc Blade, 8" 7 G008 G Hex Head Cap Screw, 5 6"-8 x ⅝" Lock Nut, 5 6"-8, Grade 8 8 G05 Hex Head Cap Screw, ⅝"- x 9" 9 GD380- Sleeve, ⅝" I.D. x ⅞" O.D. x ⅞" Long 0 GD956 Half Wheel GA67 Bearing GD9305 Tire 3 GA04 Bearing 4 GD0473 Bearing Housing 5 G047 Rivet, ¼" x ½" 6 G0006 Hex Head Cap Screw, ⅝"- x ¼" 7 GD845 Dust Cap A GA Single Press Wheel Complete W/Bearing (Items 7 And 0-) B GA680 - Covering Disc Blade Complete W/Bearing (Items 6 And 3-5) Rev. 9/ 37

38 V Closing Wheels Row Unit 006 and on (IP08) Rev. 9/

39 Row Unit 006 and on V Closing Wheels ITEM PART NO. QTY. (Per Row) GD90 G DESCRIPTION Nylon Half Wheel Hex Head Cap Screw, ¼"-0 x " GD085 Rubber Tire, " x " 3 GA67 Bearing 4 GA6597 GA67 5 GB054 G033 G009 Cast Iron Closing Wheel W/Bearing Bearing Lever Hex Head Cap Screw, 5 6"-8 x ½" Lock Nut, 5 6"-8, Grade 8 6 GA83 Arm 7 GB068 Wheel Arm Mount 8 G000 G387 9 G49 G035 G GB08 Stepped Bushing GB039 Eccentric Bushing G0 Lock Nut, ½"-3 3 GD8460 Spring 4 GK345 GD4065 G0599 G0308 G00 5 G003 G39 GD09 G030 G007-3 Hex Head Cap Screw, ⅜"-6 x " Flat Washer, ⅜" SAE Carriage Bolt, ½"-3 x ¼" Carriage Bolt, ½"-3 x ½" (Used W/Straight Drop In-Furrow Granular Chemical Bracket) Flat Washer, ⅜" SAE Closing Wheel Shield Kit W/Hardware and Instruction Closing Wheel Shield Carriage Bolt, ⅜"-6 x ¼" Carriage Bolt, ⅜"-6 x ¾" Hex Nut, ⅜"-6 Hex Head Cap Screw, ⅝"- x 3½" Flat Washer, ⅝" SAE Bushing, 4 64" I.D. x ⅞" O.D. x ¼" Long Lock Washer, ⅝" Lock Nut, ⅝"- A GA Rubber Closing Wheel Complete W/Bearing (Items -3) Rev. 9/ 39

40 Drag Closing Attachment Row Unit 006 and on (IP0) ITEM PART NO. QTY. DESCRIPTION (Per Row) GD509 Rear Bracket G0007 G030 G004 3 GA83 Arm 4 GD33 Blade 5 GD508 Front Bracket 6 G0599 G09 G387 G Hex Head Cap Screw, ⅝"- x ½" Lock Washer, ⅝" Hex Nut, ⅝"- Carriage Bolt, ⅜"-6 x ¼" Lock Washer, ⅜" Flat Washer, ⅜" SAE Hex Nut, ⅜"-6 A G7566X - Drag Closing Attachment Complete (Items -6) 40 Rev. 9/

41 This page left blank intentionally.

42 Hopper Support and Meter Drive Row Unit 006 and on (IP09) Rev. 9/

43 Row Unit 006 and on Hopper Support and Meter Drive ITEM PART NO. QTY. (Per Row) GA007 G06 G0309 GA055 G006 G387 G008 3 GD39 G060 G G075 G39 G04 DESCRIPTION Hopper Hold Down Latch Serrated Flange Nut, ¼"-0 Carriage Bolt, ¼"-0 x ⅝", Grade Hopper Support Hex Head Cap Screw, ⅜"-6 x 3½" Flat Washer, ⅜" SAE Lock Nut, ⅜"-6 Knob Spring Pin, ¼" x ½" External Retaining Ring, ⅝" Hex Head Cap Screw, ⅝"-8 x ¼" Flat Washer, ⅝" SAE Lock Nut, ⅝"-8 5 GB08 Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long 6 GB034 Hopper Mount 7 GB033 G060 G GA037 GA43 9 GD43 Spring 0 GD5747 Shaft GB078 G0546 Clutch Adapter Plate Serrated Flange Nut, 5 6"-8 Carriage Bolt, 5 6"-8 x ¼" Double Sprocket And Bearing, Drive Clutch, /9 Tooth (Mechanical) Double Sprocket And Bearing, Drive Clutch, /8 Tooth (EdgeVac) Coupler Spring Pin, 3 6" x ¼" A GA44 - Meter Drive Assembly, /8 Tooth (Items 3 And 8-) (EdgeVac Shown) B GA05 - Meter Drive Assembly Complete, /9 Tooth (Items 3 And 8-) Rev. 9/ 43

44 Row Unit 006 and on 44 Rev. 9/

45 Row Unit 006 and on Seed Hopper and Lid (METR/RU87e) ITEM PART NO. QTY. DESCRIPTION GD79 Lid GA0634 Seed Hopper (EdgeVac) 3 GA974 Seed Hopper, Reinforced (Mechanical) Rev. 9/ 45

46 Granular Chemical Hopper and Hopper Panel Extension Row Unit 006 and on (METR4d) 46 Rev. 9/

47 Row Unit 006 and on Granular Chemical Hopper and Hopper Panel Extension ITEM PART NO. QTY. DESCRIPTION (Per Row) G387 3 Flat Washer, ⅜" SAE GD97-0 Sleeve, 9 6" Long 3 GD9 Spring 4 G00 Special Washer, ⅜" x ½" O.D. 5 GD06 Sleeve, 3 6" Long 6 GD96 Idler 7 G008 Lock Nut, ⅜"-6 8 G0670 Hair Pin Clip, No. 3 9 GD059L GD059R 0 G000 G09 G03 G Support, L.H. (Shown) Support, R.H. Hex Head Cap Screw, ⅜"-6 x ¾" Lock Washer, ⅜" Carriage Bolt, 5 6"-8 x ¾" Serrated Flange Nut, 5 6"-8 G035 Hex Head Cap Screw, ⅜"-6 x ¾" 3 G External Retaining Ring, ⅝" 4 GD305 Plate 5 A0759 Hopper Panel Extension (Non-Stock Item) (Sub Wholegoods Order Code ) 6 GD44 4 Block 7 G003 G06 Hex Head Cap Screw, ¼"-0 x ¾" Serrated Flange Nut, ¼"-0 8 GD060 Hinge 9 GA837 Hopper 0 GA4444 Lid GD39 Knob G060 Spring Pin, ¼" x ½" Rev. 9/ 47

48 Granular Chemical Meter and Meter Drive Row Unit 006 and on RUA05/RUB08(RU9a) ITEM PART NO. QTY. DESCRIPTION (Per Row) G External Retaining Ring, ⅝" GD39 Knob 3 G060 Spring Pin, ¼" x ½" See Granular Chemical Hopper and Hopper Panel Extension on page P3 5 GA8364 Sprocket And Bearing, Drive Clutch, 4 Tooth 6 GD43 Spring 7 GD40 Shaft 8 GB078 Coupler 9 G0546 Spring Pin, 3 6" x ¼" 0 GD97 Shaft G09 G057 GD748 Feed Roller, Hex Bore 3 GB05 Bearing 4 GD758 Hex Bushing 5 G GR Hex Socket Head Cap Screw, No. 0-4 x ⅞" Lock Washer, No. 0 Chain, No. 4, 08 Pitch Including Connector Link Connector Link, No. 4 6 G0660 Wave Washer, ½" 7 G385 Flat Washer, ¼" SAE 8 G0570 Slotted Hex Self-Tapping Screw, ¼"-0 x ¾" 9 G073 Slotted Hex Self-Tapping Screw, No. 0 x ⅜" 0 GD06 Support Strap GD063 Metering Gate GB06 Granular Housing A GA836 - Granular Chemical Meter Complete (Items, 9, 0, -4 And 6-) B GA Granular Chemcial Meter Clutch (Items -3 and 5-9) 48 Rev. 9/

49 This page left blank intentionally.

50 Granular Chemical Banding Options Row Unit 006 and on RUA06/RUA073(RU0mm/RU83m) 50 Rev. 9/

51 Row Unit 006 and on Granular Chemical Banding Options ITEM PART NO. QTY. DESCRIPTION GD43 Funnel G09 Wire Hose Clamp, ¾" 3 GD947 Hose, 7 6" x 8" 4 G053 Slotted Pan Head Self-Tapping Screw, No. 0 x ½" 5 GA6907 G0864 G0757 G GD0963 G385 G00 7 GD0984 Spacer 8 GD5L - Hanger Bracket, L.H. 9 G045 - Cotter Pin, ⅛" x ½" 0 GD5R - Hanger Bracket, R.H. G030 G07 G Slope-Compensating Bander W/Hardware (4½" Band Width) Uni-Clamp Pan Head Screw, No. 0-3 x ¼" Hex Nut, No. 0-3 U-Bolt, ½" x 5 6" x ¼"-0 Flat Washer, ¼" SAE Lock Nut, ¼"-0, Grade B Carriage Bolt, ¼"-0 x ¾", Grade Lock Washer, ¼" Hex Nut, ¼"-0 GD6 - Hanger 3 GA075 - Diffuser, 4" Band 4 G0306 G09 G Carriage Bolt, ⅜"-6 x " Lock Washer, ⅜" Hex Nut, ⅜"-6 5 GD8 - Clamp 6 G035 Carriage Bolt, ½"-3 x ½" (Replaces Existing ½" x ¼" Hardware) 7 GA674 Bracket (Straight Drop In-Furrow) 8 GK385 G0003 G387 - Bander Shield Kit W/Hardware And Instruction Hex Head Cap Screw, ⅜"-6 x ½" Flat Washer, ⅜" SAE Rev. 9/ 5

52 Spring Tooth Incorporator Row Unit 006 and on RUA055(RU95) ITEM PART NO. QTY. DESCRIPTION (Per Row) G06 4 Serrated Flange Nut, ¼"-0 GD460 Eyebolt, ¼"-0 3 G Twin Loop Chain, 9 Links 4 GD43 Front Bracket 5 G0305 G059 G06 6 GD45 7 Spring Tooth 7 G0305 G Carriage Bolt, ⅜"-6 x " External Tooth Lock Washer, ⅜" Serrated Flange Nut, ⅜"-6 Carriage Bolt, ⅜"-6 x " Serrated Flange Nut, ⅜"-6 8 GD44 Rear Bracket 9 GA094 Cable Assembly 5 Rev. 9/

53 Row Unit 006 and on Row Unit Mounted No Till Coulter (D4398/RU0c/RU5) STYLE A STYLE B ITEM PART NO. QTY. (Per Row) G0574 G0 4 4 DESCRIPTION Carriage Bolt, ½"-3 x ¼" Lock Nut, ½"-3 GA565 Arm (Style A) 3 G0036 G007 4 G0574 G GD677 Adapter 6 GA864 GA8603 GD65 7 GD7803 GD7804 GD954 8 GD Spacer 9 GA50 Arm (Style B) Hex Head Cap Screw, ⅝"- x 4" Lock Nut, ⅝"- Carriage Bolt, ½"-3 x ¼" Lock Nut, ½"-3 Hub W/Bearing and Retaining Ring Bearing, Double Row Retaining Ring, 7 6" Disc Blade, Fluted, ", 8 Flutes (Shown) Disc Blade, Bubbled, " Disc Blade, Fluted, ¾", 3 Flutes Rev. 9/ 53

54 Row Unit Mounted Bed Leveler Row Unit 006 and on (IP83) Rev. 9/

55 Row Unit 006 and on Row Unit Mounted Bed Leveler ITEM PART NO. QTY. DESCRIPTION (Per Row) G0536 Detent Pin, ½" x ½" Grip G0597 Square Head Set Screw, ⅝"- x ¼" 3 G0503 Hex Jam Nut, ⅝"-, Grade 4 GA579 Mounting Bracket 5 GD Bushing, " O.D. x 9 6" I.D. x 7 6" Long 6 G0039 G389 G0 7 GD7890 Link 8 GA575 Anchor 9 G007 G389 G0 0 GA589 Leveler GD866 Blade G0303 G386 G009 3 G0585 G389 G Hex Head Cap Screw, ½"-3 x ¾" Flat Washer, ½" SAE Lock Nut, ½"-3 Hex Head Cap Screw, ½"-3 x ½" Flat Washer, ½" SAE Lock Nut, ½"-3 Carriage Bolt, 5 6"-8 x " Flat Washer, 5 6" SAE Lock Nut, 5 6"-8, Grade 8 Hex Head Cap Screw, ½"-3 x 3¼" Flat Washer, ½" SAE Lock Nut, ½"-3 Rev. 9/ 55

56 Row Unit Mounted Disc Furrower Row Unit 006 and on (IP84) Rev. 9/

57 Row Unit 006 and on Row Unit Mounted Disc Furrower ITEM PART NO. QTY. DESCRIPTION (Per Row) GA579 Mounting Bracket GD7890 Link 3 GA575 Anchor 4 G007 G0 Hex Head Cap Screw, ½"-3 x ½" Lock Nut, ½"-3 5 GA578 Support Arm 6 GD787-0 Spacer, 6" I.D. x ¾" Long 7 GD Spacer, 6" I.D. x ½" Long 8 G057 G006 9 GD783 GD GA5654 GA GD3 Dust Cap G038 G007 G39 3 G389 G007 G0 4 G0585 G389 G0 Truss Head Slotted Machine Screw, 5 6"-8 x ⅞" Hex Nut, 5 6"-8 Disc Blade, Solid, " (Shown) Disc Blade, Notched, " Hub W/Bearings Bearing Hex Head Cap Screw, ⅝"- x 4½" Lock Nut, ⅝"- Flat Washer, ⅝" SAE Flat Washer, ½" SAE Hex Head Cap Screw, ½"-3 x ½" Lock Nut, ½"-3 Hex Head Cap Screw, ½"-3 x 3¼" Flat Washer, ½" SAE Lock Nut, ½"-3 5 G0536 Detent Pin, ½" x ½" Grip 6 G0039 G0 Hex Head Cap Screw, ½"-3 x ¾" Lock Nut, ½"-3 7 G389 Flat Washer, ½" SAE 8 GD Bushing, " O.D. x 9 6" I.D. x 7 6" Long 9 G0597 Square Head Set Screw, ⅝"- x ¼" 0 G0503 Hex Jam Nut, ⅝"-, Grade Rev. 9/ 57

58 Row Unit Mounted Residue Wheel Row Unit 006 and on (RU03dd/RU03d) STYLE B STYLE A 58 Rev. 9/

59 Row Unit 006 and on Row Unit Mounted Residue Wheel ITEM PART NO. QTY. DESCRIPTION (Per Row) GD3 Dust Cap GD055 Wheel, Tine, ⅜" x " 3 G0006 Hex Head Cap Screw, ⅝"- x ¼" 4 GD974 Backing Plate 5 G033 G Hex Head Cap Screw, 5 6"-8 x ½" Lock Nut, 5 6"-8, Grade 8 6 GD970 Spacer, ½" x 3 6" Long 7 GA6838 Wheel Mount 8 G0033 G08 G00 9 GD5857 Spring 0 G0045 G08 G00 G0348 G0 Hex Head Cap Screw, ½"-3 x 3½" Lock Washer, ½" Hex Nut, ½"-3 GD975 Spacer, ½" x 3" Long 3 GA6834 Lower Link 4 GA683 Mount 5 G0574 G0 6 GA6833 Upper Link 7 G037 G050 8 GA5654 GA Hex Head Cap Screw, ½"-3 x 4½" Lock Washer, ½" Hex Nut, ½"-3 Hex Head Cap Screw, ½"-3 x 5" (Lockup Bolt) Lock Nut, ½"-3 Carriage Bolt, ½"-3 x ¼" Lock Nut, ½"-3 Hex Head Cap Screw, ½"-3 x 3", Full Thread Hex Jam Nut, ½"-3, Grade Hub W/Bearings Bearing 9 GD534 - Cover 0 GB0387 Wheel, Tine, ⅜" x " A GA Wheel Assembly, Tine, R.H. (Items, 4, 5 and 8) B GA36 - Wheel Assembly, Tine, R.H. (Items 4, 5, 8 and 0) Rev. 9/ 59

60 Coulter Mounted Residue Wheels Row Unit 006 and on (RU04uuu/RU53) STYLE A - Used With Style A Row Unit Mounted No Till Coulter STYLE B - Used With Style B Row Unit Mounted No Till Coulter 60 Rev. 9/

61 Row Unit 006 and on Coulter Mounted Residue Wheels ITEM PART NO. QTY. DESCRIPTION (Per Row) GD3 Dust Cap G000 G0503 Hex Head Cap Screw, ⅝"- x 3" Hex Jam Nut, ⅝"-, Grade 3 GD055 Wheel, Tine, ⅜" x " 4 GA5654 GA04 - Hub W/Bearings Bearing 5 GA45 Cam 6 GD059 Spring 7 G389 Flat Washer, ½" SAE 8 G0974 Lock Nut W/Nylon Insert, ½"-3 9 G098 G389 G0974 Hex Head Cap Screw, ½"-3 x 9½", Grade 8 Flat Washer, ½" SAE Lock Nut W/Nylon Insert, ½"-3 0 GA77 Mount GD056 Sleeve, 7½" G03 Machine Bushing, ⅝" (.030" Thick) 3 GA8760 G G033 G009 - Weed Guard W/Spring Pin Spring Pin, ¼" x " Hex Head Cap Screw, 5 6"-8 x ½" Lock Nut, 5 6"-8, Grade 8 5 GD974 Backing Plate 6 GB0387 Wheel, Tine, ⅜" x " 7 GB040 Mount 8 G36 GB0383 G39 G8 9 GA450 Locking Pin 0 G0003 G09 Hex Head Cap Screw, ¾"-0 x 0½" Bushing, ⅛" O.D. x 5 3" I.D. x ¾" Long Flat Washer, ¾" SAE Lock Nut, ¾"-0 Hex Head Cap Screw, ⅜"-6 x ½" Lock Washer, ⅜" A B GA7446 GA7445 GA36 GA Wheel Assembly, Tine, R.H. (Items 3, 4, 4 and 5) (Shown) Wheel Assembly, Tine, L.H. (Items 3, 4, 4 and 5) Wheel Assembly, Tine, R.H. (Items 4, 4, 5 and 6) (Shown) Wheel Assembly, Tine, L.H. (Items 4, 4, 5 and 6) C GK467 - Residue Wheel Mount Kit (Items 7-0) Rev. 9/ 6

62 Frame Mounted Coulter W/Residue Wheels Row Unit 006 and on (RU35c/RU35g/RU53b/RU35hh) With Residue Wheels STYLE B STYLE A 6 Rev. 9/

63 Row Unit 006 and on Frame Mounted Coulter W/Residue Wheels ITEM PART NO. QTY. DESCRIPTION (Per Row) G00 Hex Head Cap Screw, ¾"-0 x " GA9844 Plate W/Angle 3 G Hex Head Cap Screw, ½"-3 x ¾" 4 GA93 Coulter Frame 5 G Hex Head Cap Screw, ⅝"- x ½" G007 4 Lock Nut, ⅝"- 6 G0400 G0 7 GD86 Spring Anchor Bar 8 G G0 4 9 GD87 Adapter 0 GA864 GA8603 GD65 Retaining Ring, 7 6" GD7803 GD7804 GD Hex Head Cap Screw, ¾"-0 x 6½" Lock Nut, ¾"-0 Carriage Bolt, ½"-3 x ¼" Lock Nut, ½"-3 Hub W/Bearing and Retaining Ring Bearing, Double Row Disc Blade, Fluted, ", 8 Flutes (Shown) Disc Blade, Bubbled, " Disc Blade, Fluted, ¾", 3 Flutes GB03 Spring Seat 3 GD87 Compression Spring 4 GD89 Sleeve 5 G0046 G007 Hex Head Cap Screw, ⅝"- x 5" Lock Nut, ⅝"- 6 GA9845 G Coulter Arm W/Grease Fitting Grease Fitting, 45, ¼"-8 7 G00 G007 Hex Head Cap Screw, ⅝"- x 5½" Lock Nut, ⅝"- 8 GB08 3 Bushing, 3" I.D. x ⅞" O.D. x 9 3" Long 9 GD3 Dust Cap 0 G000 G0503 Hex Head Cap Screw, ⅝"- x 3" Hex Jam Nut, ⅝"-, Grade GD055 Wheel, Tine, ⅜" x " GA5654 GA04 - Hub W/Bearings Bearing 3 GD974 Backing Plate 4 G033 G009 Hex Head Cap Screw, 5 6"-8 x ½" Lock Nut, 5 6"-8, Grade 8 5 G03 Machine Bushing, ⅝" (.030" Thick) 6 GA986 G Weed Guard W/Spring Pin Spring Pin, ¼" x " 7 GA9865 Mount 8 GA986 Cam 9 GD059 Spring 30 G0974 Lock Nut W/Nylon Insert, ½"-3 3 G0005 G007 4 Hex Head Cap Screw, ⅝"- x ¾" Lock Nut, ⅝"- 3 GA9864 Support 33 G004 G00 Hex Head Cap Screw, ½"-3 x " Hex Nut, ½"-3 34 G00 G39 G0730 Hex Head Cap Screw, ⅝"- x 5½" Flat Washer, ⅝" SAE Lock Nut W/Nylon Insert, ⅝"- 35 GD470 Sleeve, 3" 36 GB0387 Wheel, Tine, ⅜" x " A B GA7446 GA7445 GA36 GA Wheel Assembly, Tine, R.H. (Items -4) (Shown) Wheel Assembly, Tine, L.H. (Items -4) Wheel Assembly, Tine, R.H. (Items, 3, 4 and 36) (Shown) Wheel Assembly, Tine, L.H. (Items, 3, 4 and 36) Rev. 9/ 63

64 This page left blank intentionally.

65 ROW UNIT ASSEMBLY & INSTALLATION INSTRUCTIONS (SDS Planters w/mechanical Seed Metering) IS69 Rev. /08 Throughout these instructions the symbol and/or the words NOTE, IMPORTANT, CAUTION, WARNING or DANGER are used to call your attention to important information. The definition of each of these terms follows: NOTE: Indicates a special point of information or addresses a machine adjustment. IMPORTANT: Indicates an operation or maintenance condition which, if not corrected, could result in damage to machine, property, crops or the environment. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate personal injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious personal injury. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious personal injury. 0 Rev. /08

66 SAFETY PRECautions IS69 WORK AREA Make sure there are no persons near the planter when row markers are in operation. Always install all lockup devices and/or lower planter to the ground before working under the unit. Never clean, lubricate or adjust a machine that is in motion. Before applying pressure to the hydraulic system, make sure all connections are tight and that hoses and fittings have not been damaged. Hydraulic fluid escaping under pressure can have sufficient force to penetrate skin, causing injury or infection. The seed and fertilizer metering systems of this planter are designed to be driven by ground tires. Hydraulic motors power the seed delivery systems. The use of aftermarket hydraulic, electric or PTO drives may create serious safety hazards to you and others nearby. Always follow all appropriate safety standards and practices to protect you and others near this planter from injury. Make sure all safety shields are installed correctly. The row unit has been designed and built with your safety in mind. Do not make any alterations or changes to this equipment. Any alteration to the design or construction may create safety hazards. Keep the work area clean and dry. Wet or oily floors are slippery. Wet spots can be dangerous when working with electrical equipment. Make sure the service area is adequately vented. Be sure all electrical outlets and tools are properly grounded. Use adequate light for the job. Be prepared if an accident or fire should occur. Know where first aid kits and fire extinguishers are located and know how to use them. SAFETY WARNING SIGNS The WARNING sign illustrated on this page is placed on the machine to warn of hazards. This and other warning found on these signs are for your personal safety and the safety of those around you. OBSERVE THESE WARNINGS! Keep these signs clean so they can be observed readily. Wash with soap and water or cleaning solution as required. Replace WARNING signs should they become damaged, painted over or if they are missing. Check the reflective decals and SMV sign periodically. Replace if they show loss of any of their reflective properties. When replacing decals, clean the machine surface thoroughly using soap and water or cleaning solution to remove all dirt and grease. Part No. G700-5 (Located on the under side of each granular chemical hopper lid.) 0 Rev. 8/07

67 INTRODUCtion IS69 The KINZE Pull Row Units have been assembled as completely as possible before shipment. Read completely through all instructions before beginning assembly. Before beginning set-up, using the shipping order and the contents listings in each instruction, check to be sure you have all the packages needed to complete assembly. GENERAL INFORMATION The information used in these instructions was current at the time of printing. However, due to KINZE s continual attempts to improve its product, production changes may cause your machine to appear slightly different in detail. KINZE Manufacturing, Inc. reserves the right to change specifications or design without notice and without incurring obligation to install the same on machines previously manufactured. Right hand (R.H.) and left hand (L.H.), as used throughout these instructions, are determined by facing in the direction the machine will travel when in use, unless otherwise stated. (RU49) Model 3800 Planter Pull Row Unit (Shown With Optional Quick Adjustable Down Force Springs) 03 Rev. 8/07

68 MOUNTING BOLTS AND HARDWARe IS69 All hardware furnished with the row unit unless otherwise noted is SAE Grade 5. Grade 5 cap screws are marked with three radial lines on the head. If hardware must be replaced, be sure to replace it with hardware of equal size, strength and thread type. Refer to the torque values chart when tightening hardware. It is suggested that hardware be left somewhat loose until all parts have been assembled. This especially applies to bearing flanges and idler sprockets. Then as a final step, tighten all hardware to the torque value specified in the chart. NOTE: Over tightening hardware can cause as much damage as under tightening. Tightening hardware beyond the recommended torque range can reduce its shock load capacity. Before operating the planter for the first time, check to be sure all hardware is tight. Check all hardware again after approximately the first 50 hours of operation and at the beginning of each planting season thereafter. Row Unit Parallel Linkage Bushing Bolts/Lock Nuts - 30 Ft. Lbs. (See Bushings in the Lubrication Section of the Operator & Parts Manual.) TORQUE VALUES CHART - PLATED HARDWARE Bolt Grade Grade 5 Grade 8 Diameter Coarse Fine Coarse Fine Coarse Fine ¼" 50 In. Lbs. 56 In. Lbs. 76 In. Lbs. 87 In. Lbs. 9 Ft. Lbs. 0 Ft. Lbs. 5 6" 8 Ft. Lbs. 9 Ft. Lbs. 3 Ft. Lbs. 4 Ft. Lbs. 8 Ft. Lbs. 0 Ft. Lbs. ⅜" 5 Ft. Lbs. 7 Ft. Lbs. 3 Ft. Lbs. 6 Ft. Lbs. 33 Ft. Lbs. 37 Ft. Lbs. 7 6" 5 Ft. Lbs. 7 Ft. Lbs. 37 Ft. Lbs. 4 Ft. Lbs. 5 Ft. Lbs. 58 Ft. Lbs. ½" 35 Ft. Lbs. 40 Ft. Lbs. 57 Ft. Lbs. 64 Ft. Lbs. 80 Ft. Lbs. 90 Ft. Lbs. 9 6" 50 Ft. Lbs. 60 Ft. Lbs. 80 Ft. Lbs. 90 Ft. Lbs. 5 Ft. Lbs. 30 Ft. Lbs. ⅝" 70 Ft. Lbs. 80 Ft. Lbs. 0 Ft. Lbs. 5 Ft. Lbs. 60 Ft. Lbs. 80 Ft. Lbs. ¾" 30 Ft. Lbs. 45 Ft. Lbs. 00 Ft. Lbs. 0 Ft. Lbs. 80 Ft. Lbs. 35 Ft. Lbs. ⅞" 5 Ft. Lbs. 40 Ft. Lbs. 30 Ft. Lbs. 350 Ft. Lbs. 450 Ft. Lbs. 500 Ft. Lbs. " 90 Ft. Lbs. 05 Ft. Lbs. 480 Ft. Lbs. 530 Ft. Lbs. 675 Ft. Lbs. 750 Ft. Lbs. ⅛" 65 Ft. Lbs. 300 Ft. Lbs. 600 Ft. Lbs. 670 Ft. Lbs. 960 Ft. Lbs. 075 Ft. Lbs. ¼" 375 Ft. Lbs. 45 Ft. Lbs. 840 Ft. Lbs. 930 Ft. Lbs. 360 Ft. Lbs. 500 Ft. Lbs. ⅜" 490 Ft. Lbs. 560 Ft. Lbs. 00 Ft. Lbs. 50 Ft. Lbs. 780 Ft. Lbs. 030 Ft. Lbs. ½" 650 Ft. Lbs. 730 Ft. Lbs. 450 Ft. Lbs. 650 Ft. Lbs. 307 Ft. Lbs. 670 Ft. Lbs. NOTE: Unplated hardware and bolts with lock nuts should be torqued approximately ⅓ higher than the above values. Bolts lubricated prior to installation should be torqued to 70% of value shown on chart. GRADE grade 5 grade 8 no Marks 3 Marks 6 Marks 04 Rev. 8/06

69 TABLE OF Contents is69 PULL ROW UNIT (Less Closing Wheels)...6 DOWN PRESSURE OPTIONS Quick Adjustable Down Force Springs Package...7 Pneumatic Down Pressure Package (Pull Row Unit)... See Instructions Supplied With Package CLOSING WHEEL OPTIONS Cast Iron V Closing Wheels...8 Rubber V Closing Wheels...8 OPTIONAL ATTACHMENTS Coulter Mounted Residue Wheels... 7 Frame Mounted Coulter...3 Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander...9 Residue Wheels For Frame Mounted Coulter...6 Row Unit Mounted Disc Furrower...9 Row Unit Mounted No Till Coulter...4 Row Unit Mounted Residue Wheel... FINAL INSPECTION/DELIVERY CHECKLIST/AFTER DELIVERY CHECKLIST Rev. 8/07

70 F AC T OR Y T OU R PULL ROW unit (Less Closing Wheels And Down Pressure Options) is69 NOTE: See Closing Wheel Options section of these instructions for information on the assembly of rubber V closing wheels or cast iron V closing wheels. NOTE: Row units and U-bolts are installed on the base machine. Down pressure options, seed meters, seed discs or seed tubes are not supplied with base machine. STEP Install seed metering unit with shank cover on mini-hopper. Assemble selected seed disc on meter if installing brush-type seed meters. D (RU3l/RU4g) DO NOT OVER TIGHTEN. Shank Cover 5 6" x ¾" Locking Thumbscrews STEP Repeat STEP on all row units. Check row unit drive chain alignment and routing. Repeat procedure on all row units. D Tooth Driven Sprocket Bearing Sprocket NOTE: Make sure connector link is installed with closed end oriented properly as shown. (PLTR4) Direction Of Chain Travel Closed End STEP 3 Install seed tube (not supplied as part of row unit) in shank as shown. Position hook on the front of the seed tube over lower cross pin in shank. Pivot top of seed tube forward and secure with retaining pin and locking clip. Repeat on all row units. (METR9ddd) STEP 4 Refer to the instructions supplied with the electronic seed monitor installaton instructions for additional information. If additional optional equipment is being installed on the row unit, see Optional Attachment assembly section. 06 Hook ¼" x ½" Clevis Pin And Hair Pin Clip Rev. 8/07

71 DOWN PRESSURE OPtions is69 Quick Adjustable Down Force Springs Package ( Row) () 86X Mechanical Down Pressure Package ( Row) (4)D849 Spring ()D47 Tab Lock Pin, 7 6" x ½" ()B086 Spring Anchor With the planter raised until the bottom of the toolbar is approximately 30" above the floor. Install support stands to safely hold the planter until assembly is complete. Install one down force spring to the L.H. parallel arms and one down force spring to the R.H. parallel arms. (a)install spring onto outside of lower parallel arm at spring tab with open end of spring hook facing toward seed hopper. (b) Position spring mount onto upper parallel arm, rotate mount forward and position spring onto spring mount tab with open end of spring hook toward seed hopper. (c)rotate spring down until mount aligns with hole in parallel arm as shown below and install pin. Repeat on all row units. (PLTR7e) Pin Location D D a NOTE: If no till coulters are to be installed, install all four down force springs as shown below. D D Pull Row Unit Push Row Unit NOTE: It is necessary for the operator to adjust springs according to field conditions. If springs are adjusted for too much down pressure for field conditions, it is possible for the row units to lift the planter to the extent that the drive wheels do not make sufficient contact. NOTE: See instructions supplied with Pneumatic Down Pressure Package for installation of that option. 07 Rev. 8/07

72 CLOSING WHEEL OPtions Rubber V And Cast Iron V Rubber V Closing Wheel (779X) Cast Iron V Closing Wheel ()A6434 Rubber Wheel ()A6597 Cast Iron Wheel (RU83d) Closing Wheel Arm LF99-5a is69 Eccentric Bushing Installation Holes Closing Wheel ⅝" Lock Washer ⅝" x 3 ½" Cap Screw ¼" Bushing And Lock Nut Shown With Rubber Closing Wheel ⅝" Hardened Washer Shown With Cast Iron Closing Wheels Installed A0948 Hardware Bag (6 Rows) ()003 Hex Head Cap Screw, ⅝"- x 3 ½" ()030 Lock Washer, ⅝" ()D7805 Special Washer, ⅝", Hardened ()D09 Bushing, 4 64" I.D. x ⅞" O.D. x ¼" Long ()007 Lock Nut, ⅝"- A0949 Hardware Bag (8 Rows) (6)003 Hex Head Cap Screw, ⅝"- x 3 ½" (6)030 Lock Washer, ⅝" (6)D7805 Special Washer, ⅝", Hardened (6)D09 Bushing, 4 64" I.D. x ⅞" O.D. x ¼" Long (6)007 Lock Nut, ⅝"- NOTE: Hardware for installing closing wheels is shipped in the bulk seed hopper. STEP PULL ROW UNIT CLOSING WHEEL INSTALLATION Install closing wheel on each side of arm using installation holes at the rear of the arm as shown. Assemble ⅝" x 3 ½" cap screw through ⅝" lock washer, through closing wheel, through ¼" bushing, through ⅝" hardened washer and through arm. Secure with ⅝" lock nut on inside of arm. STEP Position eccentric bushings to align closing wheels to seed trench. Tighten closing wheel attaching hardware. NOTE: Install cast iron closing wheel with beveled edge to inside as shown in photo above. Initial setting: adjust the eccentric bushing on both sides with the long portion of the eccentric straight back as shown. D Rev. 8/07

73 OPTIONAL ATTAChments Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander is69 Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander ()753X Chemical Hopper W/Meter And Bander ()A8368 Hardware Bag (Chain, Chain Idler, Meter Drive, Funnel, Hose, 4 ½" Slope-Compensating Bander And Straight Drop In-Furrow Placement Components) ()A8367 Hopper And Meter ()7888X Chemical Hopper Support Package (6)03 Carriage Bolt, 5 6"-8 x ¾" (6)060 Flange Nut, 5 6"-8 ()A0757 Hopper Panel Extension ()779X Reflective Decals Package ( Package Per Rows) (IS490) D (METR4e) The Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander is designed for use on the KINZE Pull Row Unit. This package includes parts for 4 ½" slope-compensating banding or straight drop in-furrow placement of granular chemical. DANGER: Agricultural chemicals can be dangerous. Improper selection or use can seriously injure persons, animals, plants, soil or other property. BE SAFE: Select the right chemical for the job. Handle it with care. Follow the instructions on the container label and of the equipment manufacturer. D (RU43c) Granular Chemical Hopper Be sure the G700-5 warning decal is in place on the underside of each granular chemical hopper lid. 09 Rev. 8/07

74 OPTIONAL ATTAChments Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander STEP Install hopper panel extension onto hopper support as shown below. (METR4cc) is69 5 6"-8 x ¾" Carriage Bolts And Flange Nuts STEP Install idler supplied in hardware bag as shown below. (METR4aa) 3 6" Long Sleeve Special Washer Spring 9 6" Long Sleeve ⅜" USS Washers ⅜"-6 Lock Nut ⅜" USS Washer ⅜"-6 x ¾" Cap Screw STEP 3 Install meter drive clutch supplied in hardware bag as shown below. (METR4bb) 4 Tooth Sprocket And Bearing Drive Clutch (Meter Drive) 5 6"-8 x ¾" Carriage Bolt And Flange Nut Plate 0 Rev. 8/07

75 OPTIONAL ATTAChments Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander STEP 4 Install granular chemical hopper as shown below. is69 Engage drive by rotating knob clockwise. To disengage drive turn knob counterclockwise. Align clutch drive coupler with meter shaft. Tighten hardware. (METR39a) No. 3 Hair Pin Clip Granular Chemical Hopper With Meter STEP 5 Install drive chains. Remove hopper. Install granular chemical drive chain through idler and around tooth sprocket of double sprocket in row unit drive clutch. Route chain through slot in hopper support and around granular chemical clutch sprocket. Use connecting link provided to couple chain. D RH004 (RU57b) Granular Chemical Driven Sprocket Tooth Sprocket On Seed Drive (PLTR4) NOTE: Make sure connector link is installed with closed end properly oriented as shown. Closed End DIRECTION OF CHAIN TRAVEL STEP 6 Reposition granular chemical hopper on hopper support panel and secure using two No. 3 hair pin clips. Rev. 8/06

76 OPTIONAL ATTAChments Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander is69 STEP 7 Install granular chemical funnel. The granular chemical funnel is designed to attach to the hopper support panel directly under the granular chemical meter using two No. 0 x ½" self tapping screws. The funnel can be installed facing forward or rearward, depending on application. The funnel is shown in the forward configuration for installation of 4 ½" slope-compensating banding or straight drop in-furrow placement. Slide the wire hose clamp onto the end of the hose. Install hose over funnel outlet and slide wire hose clamp into place over funnel outlet and hose to secure hose in place. (RU0oo) IMPORTANT: The hose should be shortened as required to eliminate bends, ensuring even distribution of chemical. (RU43d/RU43e) WRong RIGHT Install 4 ½" slope-compensating bander or straight drop in-furrow bracket as shown on next page. Rev. /07

77 F AC T OR T OU R F AC T OR T OU OPTIONAL ATTAChments Granular Chemical Hopper With Meter, Hopper Panel Extension And Bander 4 ½" SLOPE-COMPENSATING BANDING is69 (RU0kk/RU40) A. Install bottom of hose through shank cover, wheel arm stop and into slope-compensating bander. Install clamp at top of bander. Spacer B. Install U-bolt through holes in shank as shown at left. Secure using ¼" USS washers, lock nuts and spacer. Place plastic spacer between bander and shank side to center the bander. DO NOT over tighten lock nuts. Over tightening will crush the bander. NOTE: Hose should be shortened as required. DIRECTION OF TRAVEL Y R STRAIGHT DROP IN-FURROW PLACEMENT (RU0pp) ½" x ½" Carriage Bolt Supplied In Hardware Bag A. Attach direct drop bracket to wheel arm stop as shown below and at left. B. Insert bottom of hose through shank cover, wheel arm stop and into straight drop in-furrow bracket as shown. NOTE: Replace ½" x ¼" closing wheel attaching carriage bolt with ½" x ½" carriage bolt to install straight drop bracket. DIRECTION OF TRAVEL Y STEP 8 Install reflective decals on hopper panel extensions following instructions supplied with that package. 3 Rev. 8/07

78 OPTIONAL ATTAChments Row Unit Mounted No Till Coulter is69 Row Unit Mounted No Till Coulter With " Bubbled Blade (Style A) (()A564 Coulter Arm Assembly () D7803 " Fluted Blade (8 Flutes) Row Unit Mounted No Till Coulter With ¾" Fluted Blade (Style A) ()A564 Coulter Arm Assembly ()D954 ¾" Fluted Blade (3 Flutes) Row Unit Mounted No Till Coulter With " Fluted Blade (Style A) ()A564 Coulter Arm Assembly )D7804 " Bubbled Blade Row Unit Mounted No Till Coulter With " Bubbled Blade (Style B) (()A5 Coulter Arm Assembly () D7803 " Fluted Blade (8 Flutes) Row Unit Mounted No Till Coulter With ¾" Fluted Blade (Style B) ()A5 Coulter Arm Assembly ()D954 ¾" Fluted Blade (3 Flutes) Row Unit Mounted No Till Coulter With " Fluted Blade (Style B) ()A5 Coulter Arm Assembly )D7804 " Bubbled Blade Row unit mounted no till coulters with " bubbled," fluted or ¾" fluted blades may be used on pull row units and/ or push row units. One package is required per row. DANGER: Always install all safety lockup devices or lower machine to the ground before working under or around the machine. LF99-9a LF Style A Shown With ¾" Fluted Blade (3 Flutes) (Two Sleeves For Installing Coulter Mounted Residue Wheels) D a " Fluted Blade (8 Flutes) ¾" Fluted Blade (3 Flutes) " Bubbled Blade Style B Shown With ¾" Fluted Blade (3 Flutes) (One Sleeve For Installing Coulter Mounted Residue Wheels) 4 Rev. 8/07

79 OPTIONAL ATTAChments Row Unit Mounted No Till Coulter is69 STEP Install coulter blade onto hub. (RU0d) Remove ⅝" x 4" cap screw and remove hub from forked arm. Install coulter blade onto hub using carriage bolts and lock nuts. Tighten hardware alternately to avoid distorting the blade. LF99-9a STEP Install hub and coulter blade assembly using the top adjustment hole in the forked arm. Install hub and coulter blade assembly into the top adjustment hole in the forked arm using ⅝" x 4" cap screw and lock nut. (If bearing adapters have been removed from hub, reinstall into hub before installing hub into forked arm.) Torque ⅝" spindle bolt to 0 ft. lbs. Coulter Operation Depth Adjustment Holes D STEP 3 Attach coulter arm assembly to row unit face plate. Raise the planter until the bottom of the toolbar is approximately 30" above the floor. Install support stands to safely support the planter until assembly is complete. Attach coulter arm assembly to row unit face plate using carriage bolts and lock nuts as shown. Do not tighten completely at this time. ½" x ¼" Carriage Bolts And Lock Nuts Shown Installed On Push Row Unit STEP 4 Align coulter arm assembly. Shift coulter arm assembly within the limits of the adjustment slots (See photo in STEP 3) until coulter is aligned with row unit double disc openers. Torque ½" bolts to 57 ft. lbs. 5 Rev. 8/07

80 OPTIONAL ATTAChments Row Unit Mounted No Till Coulter is69 Important: Be sure down pressure options have been installed correctly as instructed in that section. STEP 5 Remove support stands and lower planter to the ground. 6 Rev. 8/07

81 OPTIONAL ATTAChments Coulter Mounted Residue Wheels is69 Coulter Mounted Residue Wheels Attachment (Style A) ()A743 Wheel Mount Assembly ()A7446 Wheel Assembly, R.H. ()A7445 Wheel Assembly, L.H. ()A744 Hardware Bag (4)03 Machine Bushing, ⅝" (.030" Thick) ()A8760 Weed Guard W/Roll Pin ()D3 Dust Cap ()000 Cap Screw, ⅝"- x 3" ()0503 Hex Jam Nut, ⅝"-, Grade LF99-3 Coulter Mounted Residue Wheels Attachment (Style B) ()A5 Wheel Mount Assembly ()A36 Wheel Assembly, R.H. ()A35 Wheel Assembly, L.H. ()A744 Hardware Bag (4)03 Machine Bushing, ⅝" (.030" Thick) ()A8760 Weed Guard W/Roll Pin ()D3 Dust Cap ()000 Cap Screw, ⅝"- x 3" ()0503 Hex Jam Nut, ⅝"-, Grade D a The Coulter Mounted Residue Wheel Attachment is attached to the Row Unit Mounted No Till Coulter Attachment using one ½" x 9 ½" (Style A) or ¾" x 0 ½" (Style B)cap screw, sleeve or bushings and lock nut which allows the unit to free-float. Two holes in each residue wheel mounting bracket arm allow the tined wheels to be mounted interlocked or staggered. Depth adjustment is made using a spring-loaded cam and pin with positions in ¼" increments. A high point on the cam allows the wheels to be locked up so they do not contact the ground. Model 3700 planters with 0" or " row spacings require the use of row unit extension brackets (8 each of Order Code for row) at the wing lift wheel arms when the planter is equipped with Coulter Mounted Residue Wheels. Model 3800 planters have row unit extension brackets on the 6 center row units as standard equipment. If equipped with Coulter Mounted Residue Wheels and Notched Single Disc Fertilizer Openers, row unit extension brackets (Order Code for row) are required on all inner and outer wing row units. DANGER: Always install all safety lockup devices or lower machine to the ground before working under or around the machine. 7 Rev. 8/07

82 OPTIONAL ATTAChments Coulter Mounted Residue Wheel is69 STYLE A Coulter Mounted Residue Wheels Attachment STEP Assemble wheels on arm. STEP Install wheel arm assembly on coulter arm. Install R.H. and L.H. wheel assemblies (interlocked or staggered) onto mount assembly using ⅝" x 3" cap screws, machine bushings (between wheel and weed guard), weed guard, hex jam nuts and dust caps supplied in the Hardware Bag. Torque cap screws to 0 ft. lbs. Tighten jam nuts securely. Raise the planter to transport position (except 340) and install all safety lockup devices. Insert 7 ½" sleeve into welded sleeves on no till coulter arm. Attach the mount assembly onto the no till coulter arm using the ½" x 9 ½" cap screw, ½" hardened washers and ½" lock nut supplied with the mount assembly. Torque hardware to 57 ft. lbs. NOTE: Opening in weed guard must point down. (RU04r) 7 ½" Sleeve Welded Sleeves STYLE B Coulter Mounted Residue Wheels Attachment STEP Assemble wheels on arm. STEP Install wheel arm assembly on coulter arm. Install R.H. and L.H. wheel assemblies (interlocked or staggered) onto mount assembly using ⅝" x 3" cap screws, machine bushings (between wheel and weed guard), weed guard, hex jam nuts and dust caps supplied in the Hardware Bag. Torque cap screws to 0 ft. lbs. Tighten jam nuts securely. Raise the planter to transport position (except 340) and install all safety lockup devices. Attach the mount assembly onto the no till coulter arm using the ¾" x 0 ½" cap screw, ¾" long bushings, ¾" SAE washers and ¾" lock nut supplied with the mount assembly. Torque hardware to 00 ft. lbs. NOTE: Opening in weed guard must point down. (RU53aa) Welded Sleeve 8 Rev. 8/07

83 OPTIONAL ATTAChments Row Unit Mounted Disc Furrower is69 Row Unit Mounted Disc Furrower Row Unit Mounted Disc Furrower With Solid Disc Blades With Notched Disc Blades (78X) (748X) ()A578 Support Arm ()A578 Support Arm ()A5896 Mounting Bracket Assembly ()A5896 Mounting Bracket Assembly ()0585 Cap Screw, ½"-3 x 3 ¼" ()0585 Cap Screw, ½"-3 x 3 ¼" ()0536 Pin ()0536 Pin (4)06 Washer, ½" (4)06 Washer, ½" (5)0 Lock Nut, ½"-3 (5)0 Lock Nut, ½"-3 (4)007 Cap Screw, ½"-3 x ½" (4)007 Cap Screw, ½"-3 x ½" ()0503 Jam Nut, ⅝"- ()0503 Jam Nut, ⅝"- (4)D7889 Bushing (4)D7889 Bushing ()D7890 Link ()D7890 Link ()0597 Set Screw, ⅝"- x ¼" ()0597 Set Screw, ⅝"- x ¼" ()A575 Anchor ()A575 Anchor ()A579 Mounting Bracket ()A579 Mounting Bracket () A5897 Hardware Bag () A5897 Hardware Bag ()D787-0 Spacer, ¾" ()D787-0 Spacer, ¾" ()D Spacer, ½" ()D Spacer, ½" ()0039 Cap Screw, ½"-3 x ¾" ()0039 Cap Screw, ½"-3 x ¾" ()038 Cap Screw, ⅝"- x 4 ½" ()038 Cap Screw, ⅝"- x 4 ½" ()D7805 Washer, ⅝" ()D7805 Washer, ⅝" ()007 Lock Nut, ⅝"- ()007 Lock Nut, ⅝"- ()D7889 Bushing ()D7889 Bushing ()0 Lock Nut, ½"-3 ()0 Lock Nut, ½"-3 ()D4674 Special Washer, ½", Hardened ()D4674 Special Washer, ½", Hardened ()D3 Dust Cap ()D3 Dust Cap ()A596 Solid Disc/Hub Assembly ()A5655 Notched Disc/Hub Assembly (6)006 Hex Nut, 5 6"-8 (6)006 Hex Nut, 5 6"-8 (6)057 Slotted Machine Screw (6)057 Slotted Machine Screw ()D783 Solid Disc Blade ()D8307 Notched Disc Blade ()A5654 Hub Assembly ()A5654 Hub Assembly The row unit mounted disc furrower may be equipped with either " solid or " notched disc blades. One package is required per row. DANGER: Always install all safety lockup devices or lower machine to the ground before working under or around the machine. LF Shown With Solid Disc Blades 9 Shown With Notched Disc Blades Rev. 8/07

84 OPTIONAL ATTAChments Row Unit Mounted Disc Furrower is69 STEP Install support stands. Raise the planter until the bottom of the toolbar is approximately 30" above the floor. Install support stands to safely support the planter until assembly is complete. STEP Attach lower anchor portion of mounting bracket assembly to row unit face plate. Attach lower anchor portion of mounting bracket assembly to row unit face plate using two ½" x ½" cap screws and lock nuts. Attach upper portion of mounting bracket assembly using rear hole in the row unit lower parallel arms. On each lower parallel arm install one ½" x ¾" cap screw and washer supplied in Hardware Bag through mounting bracket then through hole in lower parallel arm. Install bushing and ½" lock nut. Torque all mounting hardware to 57 ft. lbs. (RU40a) Row Unit Lower Parallel Arms Mounting Bracket Assembly ½"-3 x ¾" Cap Screw, Washer, Bushing And Lock Nut ½"-3 x ½" Cap Screw And Lock Nut DIRECTION OF TRAVEL 0 Rev. 8/07

85 OPTIONAL ATTAChments Row Unit Mounted Disc Furrower is69 STEP 3 Install support arm. Remove lynch pin from shipping storage position in mounting bracket assembly and slide support arm into place in mounting bracket assembly with the V in the angle pointed forward. Install lynch pin to secure support arm in shallowest position. See Operator & Parts Manual for additional information. (RU98f) DIRECTION OF TRAVEL STEP 4 ⅝"- x 4 ½" Cap Screw STEP 3 Lynch Pin Support Arm STEP 5 Dust Cap STEP 4 Lock Nut STEP 4 GD7805 Hardened Washer STEP 4 Spacers STEP 4 Install disc blade/hub assembly. Using ⅝" x 4 ½" cap screws, hardened washers (GD7805), ½" and ¾" spacers and lock nuts from Hardware Bag, install disc blade/hub assembly onto each side of V angle. Disc blades can be installed edge to edge or with R.H. or L.H. blade leading. If using leading set-up, use an equal number of R.H. and L.H. attachments to minimize draft. Adjust all blades equally and torque mounting hardware to specs. See Operator & Parts Manual for additional information. STEP 5 Install dust cap onto each hub assembly. STEP 6 Remove support stands and lower planter to the ground. 6/05

86 OPTIONAL ATTAChments Row Unit Mounted Residue Wheel is68 (A685) Row Unit Mounted Residue Wheel (A685) The row unit mounted residue wheel attachment is installed in front of the pull row unit. One package is required per row. DANGER: Always install all safety lockup devices or lower machine to the ground before working under or around the machine. STEP Attach row unit mounted residue wheel attachment to row unit face plate. Raise the planter until the bottom of the toolbar is approximately 30" above the floor. Install support stands to safely support the planter until assembly is complete. Attach row unit mounted residue wheel attachment to row unit face plate using ½" carriage bolts and lock nuts supplied with the attachment. STEP Center residue wheel ahead of double disc openers and torque bolts to 57 ft. lbs. STEP 3 Remove support stands and lower planter to the ground. See Row Unit Mounted Residue Wheel in the row unit operation section in the Operator & Parts Manual for additional information. Rev. 8/07

87 OPTIONAL ATTAChments Frame Mounted Coulter is69 Frame Mounted Coulter Frame Mounted Coulter With " Bubbled Blade With " Fluted Blade ()A935 Frame Mounted Coulter ()A935 Frame Mounted Coulter ()D7804 " Bubbled Blade ()D7803 " Fluted Blade (8 Flutes) Frame Mounted Coulter With ¾" Fluted Blade ()A935 Frame Mounted Coulter ()D954 ¾" Fluted Blade (3 Flutes) The frame mounted coulter is designed to allow necessary spring down pressure on the coulter for maximum penetration while exerting less shock load on the row unit. LF DANGER: Always install all safety lockup devices or lower machine to the ground before working under or around the machine. " Bubbled Blade ¾" Fluted Blade (3 Flutes) " Fluted Blade (8 Flutes) D03004b Coulter Frame LF Attaching Plate W/Angle Coulter Arm STEP Raise the planter until the bottom of the toolbar is approximately 3" above the floor. D03007b Remove seed hoppers from row units to allow easier access for installation of coulters. Reinstall hoppers after installation. STEP Install blade. Remove the hub assembly from the coulter assembly and install blade. 3 Rev. 8/07

88 OPTIONAL ATTAChments Frame Mounted Coulter is69 LF STEP 3 Reinstall hub/blade assembly into the coulter arm. Reinstall hub/blade assembly into the coulter arm using the top hole. Torque to 0 ft. lbs. STEP 4 Remove the attaching plate w/angle. D03003a Remove the attaching plate w/angle from the coulter assembly. NOTE: A portion of the angle on the attaching plate will need to be trimmed on the first row out from each wing hinge on 3650 planters as shown below. (A9844) Trim 5 ½" R.H. Side Shown D a STEP 5 Install coulter assembly. Using an overhead crane or hoist, position the coulter assembly onto the row unit mounting support plate. Slide the attaching plate w/angle up in between the toolbar and the existing row unit mounting support plate. Install the four ½"-3 x ¾" hex head cap screws. STEP 6 Center coulter blade with row unit V opener disc blades and tighten mounting bolts evenly. Torque mounting bolts to 57 ft. lbs. 4 Rev. 8/07