MK IV HORIZONTAL SLIDING DOOR REPLACEMENT PARTS BOOK

Transcription

1 MK IV HORIZONTAL SLIDING DOOR REPLACEMENT PARTS BOOK BI-PARTING DOOR SHOWN-SINGLE DOOR SIMILAR JAMISON DOOR COMPANY P.O. BOX 70 HAGERSTOWN, MARYLAND INTERNET: ECN CS-2169 AFTER INSTALLING THE DOOR PLEASE FORWARD TO JAMISON DOOR COMPANY THE MAINTENANCE DEPARTMENT OR OWNER. P/N

2 THIS PAGE LEFT BLANK ECN CS

3 CONTENTS SECTION TITLE PAGE 1. Instruction Sheet for Ordering Replacement Parts 4 2. General Information 6 3. Steel Track, Track Assembly 7 4. Plastic Track, Track Assembly 8 5. Carrier Assembly 9 6. Chain Lock Stay Roller Heavy Duty Stay Roller Stay Bracket Idler Power Unit Control Panel (for Control Panels Shipped Prior to 1/1/06) Control Panel Standard Speed (for Control Panels Shipped After 1/1/06) Control Panel Standard Speed 575 V (for Control Panels Shipped After 1/1/06) Control Panel Dual Speed (for Control Panels Shipped After 1/1/06) Control Panel Dual Speed 575 V (for Control Panels Shipped After 1/1/06) Limit Switch Assembly DMC Assembly Control Panel Box, DMC DMC Control Panel Assembly Control Panel Components Continued, DMC Control Panel Components Continued, DMC 575 V JamECO Control Box Pull Cord Switch Manual Disconnect Front Padlocking Hardware Pneumatic Reversing Edge Miscellaneous Door Parts Gasket Assembly Optional Pull Bar Handle (Single Manual Door Only) 50 ECN CS

4 NOTES: 1. INSTRUCTION SHEET FOR ORDERING REPLACEMENT PARTS 1. Sufficient information must be included with all orders so that we can give prompt and accurate service. The specific information needed includes: a. The stock number, drawing number and name of the part I. If possible give the stock number or drawing number of the part to be replaced. b. The HIC and WIC of the door. c. State whether the door is a bi-parting or single. If the door is a single state which direction it opens. d. Finish I. Galvanized (Galv), chrome (Chr), bright chrome (BChr), stainless steel (SST), or Tuffkote finish (similar to gray paint). Other coatings may be available see the applicable parts lists for information. 2. Parts highlighted in gray are no longer available. ECN CS

5 DETAIL A ECN CS

6 2. GENERAL INFORMATION ECN CS

7 3. STEEL TRACK, TRACK ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Track Support Angle Single Door LH 5 0 WIC Track Support Angle Single Door RH 5 0 WIC Track Support Angle Single Door LH 6 0 WIC Track Support Angle Single Door RH 6 0 WIC Track Support Angle Bi-Parting Door 6 0 WIC Track Support Angle Single Door LH 7 0 WIC Track Support Angle Single Door RH 7 0 WIC Track Support Angle Bi-Parting Door 7 0 WIC Track Support Angle Single Door LH 8 0 WIC Track Support Angle Single Door RH 8 0 WIC Track Support Angle Bi-Parting Door 8 0 WIC Track Support Angle Single Door LH 10 0 WIC Track Support Angle Single Door RH 10 0 WIC Track Support Angle Bi-Parting Door 10 0 WIC Flat Washer 13/16 x 13/32 x 13 GA Bolt 3/8-16 x 1-3/ Track Stop Bumper Screw Thread Form #10-24 x 1/2" Note: See instruction sheet for ordering parts. Note if the track is one or two piece construction. ECN CS

8 4. PLASTIC TRACK, TRACK ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Track Support Angle 5 0 WIC Track Support Angle 5 6 WIC Track Support Angle 6 0 WIC Track Support Angle 7 0 WIC Track Support Angle 8 0 WIC Track Support Angle 9 0 WIC Track Support Angle 10 0 WIC Galv Hex Head Washer Screw Track Stop Bumpers Leading Edge Plastic Standard Ramp LH ** Leading Edge Plastic Short Ramp LH Leading Edge Plastic Standard Ramp RH ** Leading Edge Plastic Short Ramp RH * Intermediate Track Piece #6 (Specify Length) (Single) XXX-XXX 5* Intermediate Track Piece #6 (Specify Length) (Bi-parting) XXX-XXX 6 Trailing Edge Plastic Standard Ramp LH ** Trailing Edge Plastic Short Ramp LH Trailing Edge Plastic Standard Ramp RH ** Trailing Edge Plastic Short Ramp RH * Tail Track Piece #7 (Specify Length) (Single) XXX-XXX 7* Tail Track Piece #7 (Specify Length) (Bi-parting) XXX-XXX 8 Track Stop Screw Self Tap 3/8-16 x 1-1/ Screw Thread form #10-24 x 1/ Nut Nylock 3/ Under Track Stop Bolt Machine Hex Head Washer 13 ga. X 13/16 OD X 13/32 ID *Please specify the serial number of the door when ordering. ** Short Ramps are only to be used with pull bar. Note: See instruction sheet for ordering parts. ECN CS

9 5. CARRIER ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 a Bolt 3/4-10 X a Hanger Bracket (4 & 6 Door) A a Hanger Bracket (2 Door) a Roll Pin 3/16 Dia. X a Hex Nut 3/ S.Assy. Hanger Sub-Assy. (Consist of Items in Group (a)) Galv Trolley Wheel Leading Edge SST Trolley Wheel Leading Edge Trolley Wheel Leading Edge (Heat Treated for Steel Track) Galv Trolley Wheel Trailing Edge SST Trolley Wheel Trailing Edge Trolley Wheel Trailing Edge (Heat Treated for Steel Track) * Self Tapping Screw #10-24 X 3/8 (MK III Steel Track Only) * Track Cleaner (MK III Steel Track Only) Hex Jam Nut 3/ Ext. Tooth Lock Washer 3/ Hex Bolt Self Tapping 3/8-16 X Spring Lock Washer 1/ Hex Bolt 1/2 13 X Carrier Single Carrier Single Carrier Bi-Parting Carrier Single Carrier Bi-Parting Carrier Single Carrier Bi-Parting Carrier Single Carrier Bi-Parting Trolley Wheel Spacer * Specify Door Thickness Note: See instruction sheet for ordering parts. Specify whether the door is single or bi-parting and give the WIC. ECN CS

10 6. CHAIN LOCK ECN CS

11 Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1B Galv Chain Lock Assy. LH A Galv Chain Lock Assy. RH B SST Chain Lock Assy. LH, (Items 1, 3 and 4 are Galv) A SST Chain Lock Assy. RH, (Items 1, 3 and 4 are Galv) Galv Guide Block Base Galv Plunger Galv Guide Plate Extension Bracket (RH Only) Hex Nut 3/ Set Screw 1/4 20 X 5/ Spring Galv Bushing Plate (Which includes Bushing No. 16) SST Bushing Plate (Which includes Bushing No. 16) Hex Bolt 3/8-16 X Hex Bolt 3/8-16 X Drive Link Connecting Link Pitch Offset Link Pitch Drive Chain Pitch Bushing Extension Bracket Tapping Plate Note: See instruction sheet for ordering parts. ECN CS

12 7. STAY ROLLER 2 8 Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. SST Complete Stay Roller Assy. (For Use When Stay Roller is Located in Freezer) Assy. SST Complete Stay Roller Assy. Standard Hex Bolt 3/8 16 x 2-1/ Flat Washer 1-1/16 x 33/64 x 13 GA (Freezer) Wheel Only (Cooler) Wheel Only (Freezer) Flat Washer 13/16 x 13/32 x 13 GA SST Stay Roller Bracket Hex Lock Nut 3/ * Anchor Bolt 1/2 x 3-3/ Spindle *Item is not included in assembly. Note: See instruction sheet for ordering parts. ECN CS

13 8. HEAVY DUTY STAY ROLLER Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Galv Heavy Duty Stay Roller Assy. SST Heavy Duty Stay Roller Galv Bracket SST Bracket Galv Mounting Plate SST Mounting Plate SST Flat Washer 13/16 x 13/32 x 13 GA SST Hex Head Mach Bolt 3/8-16 x 2-1/ Hex Head Mach Bolt 3/8-16 x 1-1/4 (Zn Plated) Hex Nut Nylock 3/8-16 (Zn Plated) SST Bushing Tube Polyolefin Wheel Note: See instruction sheet for ordering parts. ECN CS

14 9. STAY BRACKET Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Stay Wedge Assy Painted Yellow (For 4 Thick Door) Assy SST Stay Wedge Assy. (For 4 Thick Door) Assy Stay Wedge Assy Painted Yellow (For 6 Thick Door) Assy SST Stay Wedge Assy (For 6 Thick Door) *Kit Stay Wedge Assy Painted Yellow (For 4 Thick Door) Retrofit Kit (Floor Mount Only) *Kit SST Stay Wedge Assy (For 4 Thick Door) *Kit Retrofit Kit (Floor Mount Only) Stay Wedge Assy Painted Yellow (For 6 Thick Door) Retrofit Kit (Floor Mount Only) *Kit SST Stay Wedge Assy (For 6 Thick Door) Retrofit Kit (Floor Mount Only) *1 Hex Head Machine Screw 1/4-20 x 1-1/ Flat Washer 9/16 x ¼ x 18 Ga *3 Flat Washer 5/8 x 9/32 x 16 GA SST Lock Washer Split 1/ *5 Expansion Shield Round HD Mach Screw ¼ -20 x ¾ **7 Hex Taptite 3/8-16 x Wedge Assembly Bracket Painted Yellow (For 4 Thick Door) SST Bracket (For 4 Thick Door) Bracket Painted Yellow (For 6 Thick Door) SST Bracket (For 6 Thick Door) *Used for retrofits (items 1,3 & 5 are used to fasten floor wedge to floor) **Used for non-retrofits Note: See instruction sheet for ordering parts. When retrofitting a bi-parting door with stay brackets a RH and LH kit should be ordered. ECN CS

15 10. IDLER Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Idler Assy Sprocket Bracket Sprocket Mounting Bracket Idler Adjustment Bracket Idler Bearing Idler Sprocket Idler Spring Spacer Plate Carriage Bolt 1/2-13 x Hex Lock Nut 3/ Hex Bolt 3/8-16 x 1-1/ Hex Lock Nut 1/ Hex Bolt 3/8-16 x Hex Bolt 3/8 16 x 1 Taptite Flat Washer 1-3/4 x 13/32 x 1/ Flat Washer 1-3/8 x 9/16 x 20 GA Split Lock Washer 3/ Hex Bolt 3/8 16 x 1-1/ Note: See instruction sheet for ordering parts. ECN CS

16 11. POWER UNIT ECN CS

17 Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Power Unit Assy. (Specify Power Requirements and Give Model and Serial Numbers) X-XX X 1A Gear Box Sub-Assy. (Standard Powertron) B Gear Box Sub-Assy. (Dual Speed) Limit Switch Drive Sprocket (Standard Speed) Limit Switch Drive Sprocket (Dual Speed) A Drive Sprocket (Standard Speed and Reduced Dual Speed) B Drive Sprocket (Dual Speed) * Bearing Bracket A* a Bearing Bracket, Current Design * Bearing A* a Bearing, Current Design Assy. Bearing Bracket Assy. (Consists of Items in Group (a)) (The Current Design is a Direct Replacement for Older Designs) B a Bolt (For Mounting the Bearing Bracket) (Not Shown) C a Washer (For Mounting the Bearing Bracket) (Not Shown) D a Nut (For Mounting the Bearing Bracket) (Not Shown) Mounting Plate Motor (1/2 HP 120 VAC) Motor (1/4 HP VAC) Motor (1/2 HP VAC) (Soft Start) Motor Dual Speed ( VAC) Motor Dual Speed (480 VAC) Motor (1/4 HP 575 VAC) Motor Dual Speed (575 VAC) Motor (1/2 HP 575 VAC) (Soft Start) Clip Angle Rubber Grommet * Limit Switch Assy. (See Limit Switch Assy.) XX * Control Panel Assy. (See Control Panel Assy.) 13 Hex Nut 3/ Hex Nut 1/ Flat Washer 5/8 X 9/32 X 16 GA Rubber Washer 11/16 X 9/32 X 1/ Hex Bolt 1/4 20 X 3/ Flat Washer 1-1/4 X 9/32 X 16 GA Flat Washer 13/16 X 13/32 X 16 GA Hex Bolt 3/8-16 X Limit Switch Chain 20-1/2 Long Key 1/4 x 1/4 x Key 1/8 Square X 1 Long Split Lock Washer 3/ Hex Bolt 3/8-16 X 7/ Hex Bolt 3/8 16 X 1-1/ Mounting Bracket Connecting Link Offset Link (Not Shown) Note: See instruction sheet for ordering parts. ECN CS

18 12. CONTROL PANEL (FOR CONTROL PANELS SHIPPED PRIOR TO 1/1/2006) Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Control Panel Assy. (Give Model Number & Serial Numbers) (Specify NEMA 1, 3, 4, 4X or 12) XX *1 Housing NEMA 3, 4 or Housing NEMA Housing NEMA 4X Mounting Plate Baffle Transformer (240/480 Primary 24 Volt Secondary) Transformer (120/208/380 Primary 24 Volt Secondary) Fuse FNM Reversing Contactor Brass Cup Washer Marker Strip Terminal Strip Stop Switch Relay Pilot Light (120V or 240V) Pilot Light with Resister (480V) Time Delay Termostst (80 ) Optional Heater (20 Watt) Optional *17 Rubber Washer 11/16 X 9/32 X 1/ Self Tapping Screw #6-32 X 3/ Self Tapping Screw #6-32 X 1/ Self Tapping Screw #6-32 X 5/ Self Tapping Screw #8-32 X 3/ Round Head Machine Screw #10-32 X 3/ Self Tapping Screw #10-24 X 1/ Dual Speed Adder Block Note: See instruction sheet for ordering parts. ECN CS

19 THIS PAGE LEFT BLANK ECN CS

20 13. CONTROL PANEL POWERTRON STANDARD SPEED (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS

21 Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay Rev. Contactor 60 Hz Floor Loop Socket 11-Pins, Octal Style Time Delay Switch, Stop Thermostat Transformer Class Fuse 3AG, 1/4 Amp Fuse, 3 Amp FNQ-R VAC Counter ENM #E4B74D Floor Loop Unit 326SF24A-7, Harness 802A Radio Control Multi-Code End Stop Fuse Block 2 Poles Fuse Block 1 Pole Grounding Lug Terminal Blocks Marker, Number Enclosure, NEMA Enclosure, NEMA 4x Terminal Block 8 Rowes Enclosure, NEMA Base Plate #16 GA. x 11 x Din Rail 35mm x Bracket, Fuse Block #16 GA Baffle Plate #16 GA Bracket #16 GA Retainer #16 GA Heater Assy. 50W.120V Pilot Light Assy. NEMA 1 120V / 240V Pilot Light Assy. NEMA 1 480V Pilot Light Assy. NEMA 4 480V (STD) Pilot Light Assy. NEMA 4 240V Grounding Wire, Control Panel 14 AWG 13 Lg Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (ACTIVE MODEL NUMBERS) (ALSO SPECIFY NEMA 1, 4, OR 4X) STANDARD SPEED XX OPTIONAL KITS AVAILABLE CONTROL PANEL HEAT.. H FLOOR LOOP.. H RADIO CONTROL H TIME DELAY.. H ECN CS

22 14. CONTROL PANEL POWERTRON STANDARD SPEED 575 V (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS

23 Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay Rev. Contactor 60 Hz Floor Loop Socket 11-Pins, Octal Style Time Delay Switch, Stop Thermostat Transformer 575 Volts Fuse 3AG, 1/4 Amp Fuse, 3 Amp FNQ-R VAC Counter ENM #E4B74D Floor Loop Unit 326SF24A-7, Harness 802A Radio Control Multi-Code End Stop Fuse Block 2 Poles Fuse Block 1 Pole Grounding Lug Terminal Blocks Marker, Number Enclosure, NEMA Enclosure, NEMA 4x Terminal Block 8 Rowes Enclosure, NEMA Base Plate #16 GA. x 11 x Din Rail 35mm x Bracket, Fuse Block #16 GA Baffle Plate #16 GA Bracket #16 GA Retainer #16 GA Heater Assy. 50W.120V Pilot Light Assy. NEMA 1 480V Pilot Light Assy. NEMA 4 575V (STD) Grounding Wire, Control Panel 14 AWG 13 Lg Fuse Holder Din Rail Mtg Fuse FNM-3 3 Amp Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (ACTIVE MODEL NUMBERS) (ALSO SPECIFY NEMA 1, 4, OR 4X) STANDARD SPEED 575 VOLT XX OPTIONAL KITS AVAILABLE CONTROL PANEL HEAT.. H FLOOR LOOP.. H RADIO CONTROL H TIME DELAY.. H ECN CS

24 15. CONTROL PANEL POWERTRON DUAL SPEED (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS

25 Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay Rev. Contactor 60 Hz Aux. Contact Adder Deck A-B #100-FA40 (Dual Speed) Floor Loop Socket 11-Pins, Octal Style Time Delay Switch, Stop Thermostat Transformer Class Fuse 3AG, 1/4 Amp Fuse, 3 Amp FNQ-R VAC Counter ENM #E4B74D Floor Loop Unit 326SF24A-7, Harness 802A Radio Control Multi-Code End Stop Fuse Block 2 Poles Fuse Block 1 Pole Grounding Lug Terminal Blocks Marker, Number Enclosure, NEMA Enclosure, NEMA 4x Terminal Block 8 Rowes Enclosure, NEMA Base Plate #16 GA. x 11 x Din Rail 35mm x Bracket, Fuse Block #16 GA Baffle Plate #16 GA Bracket #16 GA Retainer #16 GA Heater Assy. 50W.120V Pilot Light Assy. NEMA 1 240V Pilot Light Assy. NEMA Pilot Light Assy. NEMA 4 240V Pilot Light Assy. NEMA 4 460V Grounding Wire, 14 AWG 13 lg Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (ACTIVE MODEL NUMBER) (ALSO SPECIFY NEMA 1, 4, OR 4X) DAUL SPEED XX OPTIONAL KITS AVAILABLE CONTROL PANEL HEAT.. H FLOOR LOOP.. H RADIO CONTROL H TIME DELAY.. H ECN CS

26 16. CONTROL PANEL POWERTRON DUAL SPEED 575 V (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS

27 Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay Rev. Contactor 60 Hz Aux. Contact Adder Deck A-B #100-FA40 (Dual Speed) Floor Loop Socket 11-Pins, Octal Style Time Delay Switch, Stop Thermostat Transformer 575 Volts Fuse 3AG, 1/4 Amp Fuse, 3 Amp FNQ-R VAC Counter ENM #E4B74D Floor Loop Unit 326SF24A-7,Harness 802A Radio Control Multi-Code End Stop Fuse Block 2 Poles Fuse Block 1 Pole Grounding Lug Terminal Blocks Marker, Number Enclosure, NEMA Enclosure, NEMA 4x Terminal Block 8 Rows Enclosure, NEMA Base Plate #16 GA. x 11 x Din Rail 35mm x Bracket, Fuse Block #16 GA Baffle Plate #16 GA Bracket #16 GA Retainer #16 GA Heater Assy. 50W.120V Pilot Light Assy. NEMA 1 575V (DS) Pilot Light Assy. NEMA 4 575V (DS) Fuse Holder Din Rail Mtg Fuse FNM-3 3 Amp Grounding Wire, Control Panel Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (GIVE MODEL NUMBER & SERIAL NUMBERS) (ALSO SPECIFY NEMA 1, 4, OR 4x) -DUAL SPEED 575 V xx OPTIONAL KITS AVAILABLE -CONTROL PANEL HEAT.H FLOOR LOOP.H RADIO CONTROL..H TIME DELAY....H ECN CS

28 17. LIMIT SWITCH ASSEMBLY ECN CS

29 Ref # Group Finish Offset Name of Part Stock No. Drawing Assy. Complete Limit Switch Assy. (Dual Speed) (NEMA1) Assy. Complete Limit Switch Assy. (Dual Speed) (NEMA 4) Housing (NEMA 4) Housing (NEMA 1) Housing (NEMA 4x) Label Base Limit Switch Mounting Block A Actuator Block (Standard) B Actuator Block (Dual Speed) Flange Bearing Pillow Block Bearing A Shaft (Standard) B Shaft (Dual Speed) Sprocket * Gasket (NEMA 3, 4, 4x or 12) * Gasket (NEMA 3, 4, 4x or 12) Switch Round Head Bolt 1/4 20 x 6 Green Round Head Bolt 1/4 20 x 6 Red Hex Head Bolt 1/4 20 x 3/ Hex Lock Nut 1/ Self Tapping Screw #6 32 x Flat Washer 1/2 x 9/32 x 16 GA Rubber Mounting Plate Flat Washer 5/8 x 9/32 x 16 GA Adapter Plate Pedestrian Opening Switch Plate Flat Head Self Tapping Screw #6 32 x Self Tapping Screw #10 24 x 3/ Split Lock Washer # Flat Washer 1/2 x 197 x 18 GA Pedestrian Opening Assy *Use item 20 for items 10 and 11 with NEMA 1 housing. Note: See instruction sheet for ordering parts. ECN CS

30 18. DMC ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing Assy. Digital Power Unit Assy. H Motor Unit; Long Sealtite; 1/2 Flexible Conduit Galv Sealtite Fitting, Straight Sealtite Fitting 90 Degree Sprocket, 40B22; PD x 3/4 ID Drive Sprocket Key, 3/16 x 3/16 x Hex Head Mach Bolt; 5/16-18NC x 3/ Hex Head Mach Bolt; 5/16-18NC x 1-1/ Galv Lock Washer, Ext; 5/16 Dia Spacer; 3/4 OD Mounting Bracket; 1/2 x 4-1/ Control Panel Assembly 16 x 14 x 8; NEMA1 H Note: See instruction sheet for ordering parts. For NEMA 4 & 4x control panel assemblies, see drawing H ECN CS

31 19. CONTROL PANEL BOX, DMC A. NEMA 1 APPLICATION Ref # Group Finish Offset Name of Part Stock No. Drawing 1 Enclosure 16 x 14 x Control Panel Assy. Bracket 10 GA (2 Required Per Unit) Notes: See instruction sheet for ordering parts. Enclosure stock numbers are shown for reference only. Warning labels are not included within the enclosure stock applications. Internal components are common for all NEMA applications. For floor loop option see H For radio control option see H B. NEMA 4 & 4X APPLICATIONS Ref # Group Finish Offset Name of Part Stock No. Drawing 1 Enclosure 16 x 14 x Control Panel Assy. Bracket 10 GA (2 Required Per Unit) Notes: See instruction sheet for ordering parts. Enclosure stock numbers are shown for reference only. Warning labels are not included within the enclosure stock applications. Internal components are common for all NEMA applications. For floor loop option see H For radio control option see H ECN CS

32 20. DMC CONTROL PANEL ASSEMBLY NOTES: 1. Enclosure not shown. Ref # Group Finish Offset Name of Part Stock No. Drawing 1 Transformer, Toroid 336 W, 50/60 HZ Radio Control Multi-Code Controller Drive Unit Grounding Lug Grommet for I Opening Retainer, Remote Control #16 GA Bracket, Transformer #12 GA Baseplate x (A16P14) Baffle Plate #16 GA Grounding Wire, Control Panel 14 AWG x 6 Lg NOTE: See instruction sheet for ordering parts. DMC control panel is only needed for a DMC drive unit. ECN CS

33 THIS PAGE LEFT BLANK ECN CS

34 21. CONTROL PANEL COMPONENTS CONTINUED, DMC NOTES: 1. Optional component 2. For fuse requirement please see the fuse replacement label within the control panel or contact the factory. ECN CS

35 Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay Relay Socket Socket, Floor Loop Transformer Class Fuse, 3 Amp FNQ-R Fuse,15 Amp FNQ-R Circuit Breaker, 20 Amp ABB S201-C Fuse, 6A FNQ-R Fuse, 12A FNQ-R Fuse, 25A FNQ-R Floor Loop Module 326SF24A-7; Harness 802A End Stop Fuse Block Pin Jumper Pin Jumper Terminal Block Beige, ZDU2. 5/3AN Terminal Block Orange, ZDU2. 5/3AN Terminal Block, Ground Terminal Barrier, Ground ZAP / TW Terminal Block Relay Allen Bradley 700-HLT-2Z Terminal Barrier, Block ZAP / TW Din Rail 35mm x 8in Note: See instruction sheet for ordering parts. ECN CS

36 22. CONTROL PANEL COMPONENTS CONTINUED, DMC 575 V NOTES: 1. Optional component 2. For fuse requirement please see the fuse replacement label within the control panel or contact the factory. Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay Relay Socket Socket, Floor Loop Transformer 575V Fuse, 2A FNM Fuse, 3A FNQ-R Fuse, 5A FNQ-R Circuit Breaker, 20 Amp ABB S201-C Floor Loop Module 326SF24A-7 Harness 802A End Stop Fuse Block Pin Jumper Pin Jumper Terminal Block Beige, ZDU2. 5/3AN Terminal Block Orange, ZDU2. 5/3AN Terminal Block, Ground Terminal Barrier, Ground ZAP / TW Terminal Block Relay Allen Bradley 700-HLT-2Z Terminal Barrier, Block ZAP / TW Din Rail 35mm x 8in Note: See instruction sheet for ordering parts. ECN CS

37 23. JAMECO CONTROL BOX ECN CS

38 Ref # Group Finish Offset Name of Part Stock Stock No. No. Drawing 1 Toggle Switch Humidity based fan control Receptacle cover Wire SO18/ Fork Terminal Ring Terminal C Compact Splice C Compact Splice Gang Lug Box Liquidtight Cord Grip ECN CS

39 24. PULL CORD SWITCH Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete WPS Switch (W/o Heat) Assy. Complete WPS Switch (W/ Heat) Pull Cord Rope W/ Tassel (Not Shown) Pull Cord Rope Vinyl 60 (Not Shown) Note: See instruction sheet for ordering parts. ECN CS

40 25. MANUAL DISCONNECT Ref # Group Finish Offset Name of Part Stock No. Drawing No. S Assy. Complete Sub-Assy. (W/ Thru-Door Operator) (4 Door) (1,2,3A,4,5,7) S Assy. Complete Sub-Assy. (for RH Leaf Bi-Part) (4 Door) (1,3B,4,7) S Assy. Complete Sub-Assy. (W/ Thru-Door Operator) (6 Door) Cable Boss Push Nut A Washer (Thru-Door Operator) B Stub Shaft/Washer Pop Rivet Back Handle Sub-Assy. (4 Door) A Back Handle Sub-Assy. (2 Door) B Back Handle Sub-Assy. (6 Door) * Disconnect Cable (Advise H.I.C., Date of Mfg and Handle) Set-Screw Vinyl Cable End Cap Turn Handle For Manual Release Label Note: See instruction sheet for ordering parts. ECN CS

41 THIS PAGE LEFT BLANK ECN CS

42 26. FRONT PADLOCKING HARDWARE ECN CS

43 Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 SST Safety Release Handle (4 Door) SST Safety Release Handle (2 Door) SST Safety Release Handle (6 Door) Galv Washer SST Washer Alum Door Cup W/o Hole Alum Door Cup W/ Hole Door Cup W/ Hole (Powder Coat Chrome) Pop Rivet Galv Staple Lock Washer Chr Staple Lock Washer Phenolic Washer Galv Staple Eye Chr Staple Eye SST Switch Plate Sub-Assy. (Power Doors Only) Pop Rivets (Power Doors Only) Galv Hasp Blade Mounting Angle Sub-Assy. (4 ) (Manual) Chr Hasp Blade Mounting Angle Sub-Assy. (4 ) (Manual) Galv Hasp Blade Mounting Angle Sub-Assy. (4 ) (Power) Chr Hasp Blade Mounting Angle Sub-Assy. (4 ) (Power) Galv Hasp Blade Mounting Angle Sub-Assy. (6 ) (Manual) Chr Hasp Blade Mounting Angle Sub-Assy. (6 ) (Manual) Galv Hasp Blade Mounting Angle Sub-Assy. (6 ) (Power) Galv Hasp Blade Mounting Angle Sub-Assy. (6 ) (Power) Galv Hasp Blade Mounting Angle Sub-Assy. (2 ) (Manual) Galv Hasp Blade Mounting Angle Sub-Assy. (2 ) (Power) A SST Hasp Blade Mounting Angle (2 ) B SST Hasp Blade Mounting Angle (4 ) C SST Hasp Blade Mounting Angle (6 ) Magnet (Power Doors Only) Galv Hasp Blade Sub-Assy. (Manual Bi-parting Door) Chr Hasp Blade Sub-Assy. (Manual Bi-parting Door) Galv Staple Chr Staple Galv Hasp Blade Sub-Assy. W/o Emergency Release 4 door, (Not a Stock Item) H SST Hasp Blade Sub-Assy. W/o Emergency Release 4 door, (Not a Stock Item) H Self Tapping Screw Pop Rivet Note: See instruction sheet for ordering parts. ECN CS

44 27. PNEUMATIC REVERSING EDGE Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Assy. (When Ordering Specify Door Model, Serial Number, Size and Slide) XX Outer Gasket Wrapper (.035 X 5 ) (HIC + 1/2 ) (Specify Length Required) Inner Wrapper (.04 X 3-3/8 ) (Ripstop Nylon) (HIC 3-1/2 ) Switch Bushing Hose (Specify Length Required) End Plug (to be Glued in Place) Plug Sub Base (Specify Length) XX Note: See instruction sheet for ordering parts. ECN CS

45 THIS PAGE LEFT BLANK ECN CS

46 28. MISCELLANEOUS DOOR PARTS ECN CS

47 Ref # Group Finish Offset Name of Part Stock No. Drawing 1 SST Leading Edge Wedge (4 & 6 ) (Single Door Only) A SST Leading Edge Wedge (2 ) (Single Door Only) Alum Front and Rear Strafing Bar 2 Single 5 0 WIC Single 6 0 WIC Bi-Part (Front) 6 0 WIC Bi-Part (Rear) 6 0 WIC Single 7 0 WIC Bi-Part (Front) 7 0 WIC Bi-Part (Rear) 7 0 WIC Single 8 0 WIC Bi-Part (Front) 8 0 WIC Bi-Part (Rear) 8 0 WIC Single 10 0 WIC Bi-Part (Front) 10 0 WIC Bi-Part (Rear) 10 0 WIC SST Trailing Edge Wedge (4 Door) A SST Trailing Edge Wedge (2 Door) B SST Trailing Edge Wedge (6 Door) Sill Gasket (.04 X 2-3/8 ) (Hypalon) Galv Front Door Pull Chr Front Door Pull Alum Rear Door Pull Cup Rear Door Pull Cup (Powder Coat Chrome) Alum Rear Door Pull Cup, Rear Door Pull Cup, 7 (Powder Coat Chrome) Alum Rear Door Pull Bar Rear Door Pull Bar (Powder Coat Chrome) Alum Rear Door Pull Bar, Rubber Bumper Track Wedge Galv Reversing Edge Retainer SST Reversing Edge Retainer Frame Wedge Ped. Opening Push Button Switch Wicket Door Cut-Out Switch Note: See instruction sheet for ordering parts. ECN CS

48 29. GASKET ASSEMBLY ECN CS

49 Ref # Group Finish Offset Name of Part Stock No. Drawing 1* Gasket Sub-Assembly Horiz. (White) 1* * * * * * * Gasket Sub-Assy. Vert. (White) (Specify Hand) 2* * * * * * Gasket Retainer 3* SST 5 0 LH * SST 5 0 RH * SST 6 0 LH * SST 6 0 RH * SST 7 0 LH * SST 7 0 RH * SST 8 0 LH * SST 8 0 RH * SST 9 0 LH * SST 9 0 RH * SST 10 0 LH * SST 10 0 RH A Head Gasket Retainer (Order Reference 3, RH) 4 SST Pan Head Screw #14 x * Gasket Outer Wrapper.04 x * Flat Gasket Retainer for Doors w/jambs (Not Shown) xx Screw (for Flat Gasket Retainer) Gasket Heat Wire (Call Factory w/serial Number) xxx-xxx *Please specify the HIC and WIC of the door that the item is to be used on. Note: See instruction sheet for ordering parts. ECN CS

50 30. OPTIONAL PULL BAR HANDLE (SINGLE MANUAL DOOR ONLY) Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Assy. (Items 3, 4, & 5 Not Included) H Oilite Bearing Shaft Collar Taptite, Hex Head 5/16 X Taptite, Hex Head 3/8 X Opener Bracket Oilite Bearing Modified Bottom Bracket Top Bracket Handle Assy Note: See instruction sheet for ordering parts. ECN CS