Nor-Cal Products. where technology takes shape. vacuum products catalog

Transcription

1 Nor-al Products where technology takes shape vacuum products catalog

2 s & Fittings Section Two.0 s & Fittings General Information 8. NW s & Fittings 9. ISO s & Fittings 9.3 S s & Fittings 38.4 F s & Fittings 45.5 luminum to Stainless Steel Transitions 67.6 Wire Seal s 68.7 EV hain lamp omponents & Hardware 69.8 dapter Fittings 73.9 Flexible Hose & ouplings 8.0 Weld Fittings & Tubing 90 opyright 07b, Nor-al Products, Inc. ll rights reserved. 7

3 SETION.0 s & Fittings s & Fittings General Information Nor-al Products manufactures a complete selection of 304 or 36 stainless steel vacuum line hardware and maintains a large inventory of flanges, fittings, gaskets, clamps, bolts, O-rings and other hardware components for prompt deliveries and to meet those unexpected demands to complete your project. hoose from more than,500 flanges, fittings, weld fittings, adapters, and aluminum to stainless steel transitions. types include NW (ISO-KF), ISO, F (onflat), S and Wire Seal as well as EV chain clamps and aluminum seals for converting NW and ISO flanges from high vacuum to UHV. Most standard vacuum components can be customized to meet your specific needs. s, Fittings, dapters & Hardware Nor-al Products flanges are made from 304 stainless steel material, which is specially processed to reduce impurities, grain size and microscopic leak paths. They are available in all commonly used high and ultra-high vacuum flange types, including S, NW (ISO-KF), ISO, F and wire seal flanges. We also offer EV chain clamps and metal seals to convert a high vacuum NW flange to ultra-high vacuum. Fittings are available with or without flanges. Weld fittings (without flanges) are typically sold to mechanical contractors for use during the fit up phase of new fab construction. Nor-al Products provides a broad range of adapter fittings in order to connect two dissimilar types of components. They are made from 304 stainless steel and are TIG welded, cleaned and leak checked for vacuum service. Flexible Hose & ouplings Nor-al Products is your source for a comprehensive range of tubing, flexible vacuum connections, hose, and couplings, along with PV hose. Flexible hose and couplings can dampen vibration issues and offer an expansion joint between pieces of equipment, and compensate for unusual geometries. Flexible vacuum connections are typically made by using edge welded bellows, hydroformed flexible couplings, flexible hose or PV hose. Nor-al Products offers flexible couplings and flexible hose as standards. PV hose offers a low-cost alternative to stainless steel flexible hose. Edge-welded bellows provide the greatest stroke and flexibility but are more susceptible to damage. They are also more expensive. Edge welded bellows assemblies can be provided in a variety of materials as specials. luminum to Stainless Steel Transitions luminum/stainless steel transitions are used with standard F flanges for UHV sealing and have the ability to provide value-added, custom designed vacuum-line assemblies in a variety of configurations and sizes. Thermal ontrol Nor-al Products carries a full line of heater jackets, controllers, insulators and accessories to fit any of our valves or vacuum line components. Heating vacuum lines reduces the build-up of semiconductor process by-products in valves and other exhaust line components while reducing particle generation and system downtime. Uniform line heating will minimize condensation and particle build-up in gas delivery and pump lines. Stainless Steel Tubing Nor-al Products consumption of stainless steel tubing for its own products makes it possible to offer 304 and 36L stainless steel tubing in lengths up to 0 feet. 304 stainless steel tubing standard finishes are white pickled (Number unpolished), bright annealed or polished and ID, depending on the size. 36L stainless steel tubing is offered with a bright annealed finish only. right annealed and polished tubing has been pickled and passivated. Polished tube can be described as No. 4 polished. The surface meets STM 70, and has received a 50 grit polish on the and 80 grit on the ID. Special cleaning, materials and surface finishes are available for an additional charge. 8

4 s & Fittings NW General Information SETION. SPEIFITIONS Tube sizes: 3 /8 to inches (9.53 to 50.8mm) Materials : 304 or 36L stainless steel O-rings: FKM, una & silicone Fittings Tube finishes: eadblast standard (Tumbled & electropolish available) Fasteners: Wing nut, SureSeal, bulkhead & chain clamps Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º Silicone: -50º to 30º una: -30º to 0º Metal seal: -70 to 50 Nor-al Products NW flanges are designed to ISO 86 specifications for standard US tube sizes from 3 /8 to inches (9.53 to 50.8mm). They are compatible with other manufacturers ISO-KF style flanges. NW flanges utilize an aluminum clamp with a single wing nut fastener or a lock-over-center clamp allowing Wingnut lamp frequent disassembly without tools. The vacuum seal is effected by the application of uniform pressure from the clamp on the 5º surface of the 304 stainless steel flanges. The mating flange surfaces compress a FKM O-ring held in place by a centering ring. The resultant seal can be used in vacuum applications of up O-ring O-ring with entering Ring Tube entering Ring to 0-8 mbar and baked to 00º, however sustained baking above 50º may result in deterioration of O-rings. dditionally, NW flanges allow components to be rotated before assembly for ease of component alignment. NW flanges are available on virtually all Nor-al Products components and fittings. Nor-al Products manufactures a full line of NW adapters so you can add to or build an entire system with NW components. (See adapters - Section.7) NW flanges can also be used with EV chain clamps and aluminum seals to obtain a UHV seal bakeable to 50º. (EV chain clamps and seals are described in detail in Section.7.) Trapped entering Rings Nor-al Products trapped centering rings for NW flanges feature easy assembly with exact centering and are appropriate for vacuum or pressure by externally supporting the sealing ring. Trapped O-rings are intended for use where pressures range from rough vacuum to above atmosphere. pplications include vacuum pump exhaust lines and abatement tools. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. SureSeal lamp with Lanyard Lock 9

5 SETION. s & Fittings NW ored lank s & lank Off aps.50 (3.8).50 (3.8) Diagram Diagram NW ored lank s (NW) DIGRM TUE NW / 8 (9.53) 0.38 (9.65) 0.36 (8.8).8 (9.97) NW / (.70) 0.5 (.95) 0.45 (.46).8 (9.97) NW / 8 (9.53) 0.38 (9.65) 0.36 (8.8).8 (9.97) NW / (.70) 0.5 (.95) 0.45 (.46).8 (9.97) NW / 4 (9.05) 0.76 (9.30) 0.68 (7.7).8 (9.97) NW / 8 (9.53) 0.38 (9.65) 0.36 (8.8).575 (40.0) NW / (.70) 0.5 (.95) 0.45 (.46).575 (40.0) NW / 4 (9.05) 0.76 (9.30) 0.75 (8.6).575 (40.0) NW-5-00 (5.40).0 (5.65) (3.83).575 (40.0) NW / 8 (9.53) 0.38 (9.65).36 (8.8).6 (54.86) NW / (.70) 0.5 (.95) 0.45 (.46).6 (54.86) NW / 4 (9.05) 0.76 (9.30) 0.75 (8.6).6 (54.86) NW (5.40).0 (5.65) (3.83).6 (54.86) NW / (38.0).5 (38.35).438 (36.53).6 (54.86) NW / 8 (9.53) 0.38 (9.65).36 (8.8).95 (74.93) NW / (.70) 0.5 (.95) 0.45 (.46).95 (74.93) NW / 4 (9.05) 0.76 (9.30) 0.75 (8.6).95 (74.93) NW (5.40).0 (5.65) (3.83).95 (74.93) NW / (38.0).5 (38.35).438 (36.53).95 (74.93) NW (50.80).0 (5.05).938 (49.3).95 (74.93) NW 36L Stainless Steel ored lank s (NW) DIGRM TUE NW L (5.40).0 (5.65) (3.83).575 (40.0) NW L / (38.0).5 (38.35).438 (36.53).6 (54.86) NW L (50.80).0 (5.05).938 (49.3).95 (74.93) SPEIFITIONS Tube sizes: 3 /8 to inches (9.53 to 50.8mm) Materials : 304 or 36L stainless steel O-rings: FKM, una & silicone Fasteners: Wing nut, SureSeal, bulkhead & chain clamps Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º Silicone: -50º to 30º una: -30º to 0º Metal seal: -70 to 50 lank Off aps NW (5.08).8 (9.97) NW (5.08).8 (9.97) NW (5.08).575 (40.0) NW (5.08).6 (54.86) NW (5.08).95 (74.93) 36L lank Off aps NW-6-36L 0.00 (5.08).8 (9.97) NW-5-36L 0.00 (5.08).575 (40.0) NW-40-36L 0.00 (5.08).6 (54.86) NW-50-36L 0.00 (5.08).95 (74.93) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. See Section.7 for EV metal seals 0

6 s & Fittings NW Socket Weld & Weld Neck s SETION. NW Socket Weld s TUE D E NW-0-SW / (.70).8 (9.97) 0.48 (.9) 0.5 (.95) 0.6 (5.49) - NW-6-SW 3 / 4 (9.05).8 (9.97) 0.68 (7.7) 0.76 (9.30) (0.7) - NW-5-SW (5.40).575 (40.0).03 (6.9).0 (5.65).4 (8.96) (3.83) NW-40-SW / (38.0).6 (54.86).6 (4.5).5 (38.35).64 (4.66).438 (36.53) NW-50-SW (50.80).95 (74.93).06 (5.3).0 (5.05).4 (54.36).938 (49.3).500 (.7).50 (3.8) E D.0 (3.05).575 (40.0).00 (.54) 5 NW Long Weld Neck s D NW-0FL.8 (9.97) 0.48 (.9) 0.38 (9.65) / (.70) NW-6FL.8 (9.97) 0.68 (7.7) 0.65 (5.88) 3 / 4 (9.05) NW-5FL.575 (40.0).03 (6.9) 0.87 (.0) (5.40) NW-40FL.6 (54.86).6 (4.5).37 (34.80) / (38.0) NW-50FL.95 (74.93).06 (5.3).87 (47.50) (50.80) NW 36L Stainless Steel Long Weld Neck s D D NW-5FL-36L.575 (40.0).03 (6.9) 0.87 (.0) (5.40) NW-40FL-36L.6 (54.86).6 (4.5).37 (34.80) / (38.0) NW-50FL-36L.95 (74.93).06 (5.3).87 (47.50) (50.80) NW Short Weld Neck s DIGRM TUE D E NW-0F / (.70).8 (9.97) 0.48 (.9) 0.38 (9.65) / (.70) 0.5 (.70) NW-6F 3 / (9.05) 4.8 (9.97) 0.68 (7.7) 0.65 (5.88) 3 / 4 (9.05) 0.56 (4.) NW-6F 3 / 4 (9.05).8 (9.97) 0.68 (7.7) 0.65 (5.88) 3 / 4 (9.05) 0.5 (.70) NW-5F (5.40).575 (40.0).03 (6.9).087 (.0) (5.40) 0.5 (.70) NW-40F / (38.0).6 (54.86).6 (4.5).37 (34.80) / (38.0) 0.75 (9.05) NW-50F (50.80).95 (74.93).06 (5.3).87 (47.50) (50.80) 0.75 (9.05) E.0 (3.05) Diagram.00 (.54) 5 o E.0 (3.05) Diagram.00 (.54) 5 o SPEIFITIONS Tube sizes: 3 /8 to inches (9.53 to 50.8mm) Materials : 304 or 36L stainless steel O-rings: FKM, una & silicone Fasteners: Wing nut, SureSeal, bulkhead & chain clamps Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º Silicone: -50º to 30º una: -30º to 0º Metal seal: -70 to 50 D.67 (7.07) D ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. See Section.7 for EV metal seals

7 SETION. s & Fittings NW ssembly Hardware NW Wing Nut lamps Nor-al Products Wing Nut and SureSeal NW lamps feature special centering ribs and evenly distributed clamping force to assure uniform O-ring compression and reduce the probability of failure under loads. dditional hinge knuckles and tighter manufacturing tolerances result in precise alignment and reduced side play. lamp opening is limited to facilitate one-handed installation in hard-to-reach spaces. In addition to the above features, the SureSeal clamp provides instant closure with a fixed geometry to attain optimal O-ring compression. ll NW clamps are designed and manufactured to meet Pneurop specifications for ISO-KF 0 through 50 flanges, so you can be confident of universal compatibility. We also provide chain clamps and metal seals for ISO-KF components to transform them from high vacuum to ultra-high vacuum connections. NW-0-P.69 (4.93).39 (60.76) 0.65 (5.88) NW-6-P.69 (4.93).39 (60.76) 0.65 (5.88) NW-5-P.4 (54.36).796 (7.0) 0.65 (5.88) NW-40-P.75 (69.85) (87.30) 0.65 (5.88) NW-50-P 3.50 (88.90) 4.45 (07.8) 0.70 (8.03) NW SureSeal lamps NW-0-SS.750 (44.45).39 (60.76) 0.74 (8.8) NW-6-SS.750 (44.45).39 (60.76) 0.74 (8.8) NW-40-SS.947 (74.85) (87.30) 0.74 (8.8) NW-50-SS (96.) 4.45 (07.8) (.3) NW SureSeal lamps with Lanyard NW-0-SS-L.750 (44.45).39 (60.76) 0.74 (8.8) NW-6-SS-L.750 (44.45).39 (60.76) 0.74 (8.8) NW-40-SS-L.947 (74.85) (87.30) 0.74 (8.8) NW-50-SS-L (96.) 4.45 (07.8) (.3) LMP NW lamp learance Details FLNGE MIN. DI. TO INSTLL MX. DI. LOSED MIN. DI. LOSED NW-0-P NW-0.86 (7.64).65 (67.3).75 (44.45) NW-6-P NW-6.86 (7.64).65 (67.3).75 (44.45) NW-5-P NW (84.33) 3.00 (76.0).4 (56.90) NW-40-P NW (0.60) 3.7 (94.49).90 (73.66) NW-50-P NW (38.43) 4.6 (7.35) 3.69 (93.73) 0.57 D NW ulkhead lamps OF SREWS THROUGH HOLE D NW-6-P.00 (50.80).50 (38.0) 0.36 (9.7) (.86) NW-5-P.37 (60.0).89 (48.0).0387 (9.83) 6.6 (3.00) NW-40-P.94 (74.68).44 (6.98) (9.30) 6.84(46.74) NW-50-P 3.75 (95.5) 3.5 (8.55) (0.6) 8.35 (59.69) dd -M5 for metric bolts 0-3 x 5/ 8 " Screws NW ulkhead or aseplate ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. ulkhead clamps provide a simple means of fastening an NW flange to a baseplate. Each aluminum clamp is sold with stainless steel socket head cap screws and washers for attachment. Leave inch (mm) minimum between the bottom of the tapped hole and the inside of the chamber wall. ulkhead lamps NW entering Ring

8 s & Fittings NW entering Rings SETION. Nor-al Products offers aluminum and stainless steel centering rings for NW and ISO flanges. una, silicone and FKM O-rings are available for NW, while una and FKM are stocked for ISO centering rings. luminum ISO centering rings are provided with an aluminum spacer ring. Stainless steel ISO centering rings are also provided with aluminum spacer rings as an option. NW luminum entering Rings with O-ring O-RING MTERIL NW-0-R-V FKM (.4) (.58) NW-0-R- una (.4) (.58) NW-6-R-V FKM (6.99) 0.65 (5.88) NW-6-R- una (6.99) 0.65 (5.88) NW-5-R-V FKM.04 (6.0) (4.99) NW-5-R- una.04 (6.0) (4.99) NW-40-R-V FKM.64 (4.00).57 (39.88) NW-40-R- una.64 (4.00).57 (39.88) NW-50-R-V FKM.047 (5.99).967 (49.96) NW-50-R- una.047 (5.99).967 (49.96).30 (7.87).0 (5.33).54 (3.9) NW Stainless Steel entering Rings with O-ring O-RING MTERIL NW-0-R-SV FKM (.4) (.58) NW-0-R-SS Silicone (.4) (.58) NW-0-R-S una (.4) (.58) NW-6-R-SV FKM (6.99) 0.65 (5.88) NW-6-R-SS Silicone (6.99) 0.65 (5.88) NW-6-R-S una (6.99) 0.65 (5.88) NW-5-R-SV FKM.04 (6.0) (4.99) NW-5-R-SS Silicone.04 (6.0) (4.99) NW-5-R-S una.04 (6.0) (4.99) NW-40-R-SV FKM.64 (4.00).570 (39.88) NW-40-R-SS Silicone.64 (4.00).570 (39.88) NW-40-R-S una.64 (4.00).570 (39.88) NW-50-R-SV FKM.047 (5.99).967 (49.96) NW-50-R-SS Silicone.047 (5.99).967 (49.96) NW-50-R-S una.047 (5.99).967 (49.96).30 (7.87).0 (5.33).54 (3.9) NW 36L Stainless Steel entering Rings with O-ring O-RING MTERIL NW-5-R-SV-36L FKM.04 (6.0) (4.99) NW-40-R-SV-36L FKM.64 (4.00).570 (39.88) NW-50-R-SV-36L FKM.047 (5.99).967 (49.96).30 (7.87).0 (5.33).54 (3.9) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 3

9 SETION. s & Fittings NW entering Rings & Replacement O-rings.30 (7.87).0 (5.33).54 (3.9) NW Screened Stainless Steel entering Rings with FKM O-ring O-RING MTERIL MESH NW-5-R-SV-74 FKM.04 (6.0) (4.99) 74 NW-40-R-SV-74 FKM.64 (4.00).570 (39.88) 74 NW-50-R-SV-74 FKM.047 (5.99).967 (49.96) (7.87).54 (3.9).0 (5.33) NW Reducer Stainless Steel entering Rings with FKM O-ring O-RING MTERIL NW-0/6-R FKM 0.48 (.9) 0.67 (7.0) NW-0/5-R FKM 0.87 (.0).0 (5.9) NW-3/40-R FKM.34 (34.04).6 (40.89) una and Silicone O-rings available. all for pricing. For dimensions refer to the centering ring/o-ring assembly drawing on the previous page and the overpressure ring diagram this page. NW Stainless Steel entering Rings with FKM O-ring and Over Pressure Ring NW-0-R-SV-PR NW-6-R-SV-PR NW-5-R-SV-PR NW-40-R-SV-PR NW-50-R-SV-PR una and Silicone O-rings available. all for pricing. NW Stainless Steel Over Pressure Rings DESRIPTION ontains model numbers NW-0-PR and NW-0-R-SV ontains model numbers NW-6-PR and NW-6-R-SV ontains model numbers NW-5-PR and NW-5-R-SV ontains model numbers NW-40-PR and NW-40-R-SV ontains model numbers NW-50-PR and NW-50-R-SV MXIMUM PSIG NW-0-PR.5 (3.75).86 (30.) (8.79) 00 NW-6-PR.5 (3.75).86 (30.) (8.79) 00 NW-5-PR.66 (4.6).583 (40.) (8.79) 00 NW-40-PR.5 (57.5).69 (55.09) (8.79) 75 NW-50-PR.75 (69.85).60 (66.55) 0.45 (3.68) (3.9) NW Stainless Steel aptured entering Rings with FKM O-ring O-RING MTERIL MXIMUM PSIG NW-6-R-SV FKM.5 (3.75) 0.65 (5.88) 00 NW-5-R-SV FKM.66 (4.6) (4.99) 00 NW-40-R-SV FKM.5 (57.5).570 (39.88) 75 NW-50-R-SV FKM.75 (69.85).967 (49.96) 50 una and Silicone O-rings available. all for pricing..57 (3.99).35 (8.00) NW trapped centering rings are composed of an aluminum outer ring, FKM O-ring, and stainless steel centering ring NW Stainless Steel Trapped entering Rings with O-ring O-RING MTERIL NW-0/6-RT-SV FKM.8 (9.97) 0.63 (6.00) 0.9 (3.) NW-5-RT-SV FKM.58 (40.3) 0.95 (4.3).3 (33.0) NW-40-RT-SV FKM.7 (55.).58 (40.3).89 (48.0) NW-50-RT-SV FKM.95 (74.93).97 (50.04).3 (58.93) una and Silicone O-rings available. all for pricing. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. FKM O-Rings NW-0-OR-V NW-6-OR-V NW-5-OR-V NW-40-OR-V NW-50-OR-V FLNGE TYPE NW-0 NW-6 NW-5 NW-40 NW-50 Silicone O-Rings NW-0-OR-S NW-6-OR-S NW-5-OR-S NW-40-OR-S NW-50-OR-S FLNGE TYPE NW-0 NW-6 NW-5 NW-40 NW-50 una O-Rings NW-0-OR- NW-6-OR- NW-5-OR- NW-40-OR- NW-50-OR- FLNGE TYPE NW-0 NW-6 NW-5 NW-40 NW-50 4

10 s & Fittings NW Fittings SETION. SPEIFITIONS Tube sizes: / to inches (.7 to 50.8mm) Materials : 304 stainless steel (36L available upon request) O-rings: FKM, una & silicone Fittings Tube finishes: eadblast standard (Tumbled & electropolish available) Fasteners: Wing nut, SureSeal, bulkhead & chain clamps Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º Silicone: -50º to 30º una: -30º to 0º Metal seal: -70 to 50 See Section.7 for EV metal seals Nor-al Products manufactures a complete line of NW vacuum fittings. The tube portions are fabricated from 304 stainless steel. 36L stainless steel can be supplied on request. Nor-al Products makes its own elbows, and all tees and crosses are made with the pulled-port technique. This allows smooth, crevice-free butt welds to provide the maximum in cleanliness for UHV applications. akeout range is up to 00. Nor-al Products fittings are also available with F, ISO and S flanges. Standard finish is bead blasted. Electropolished finish can also be provided as an option. all for pricing. NW Half Nipples TUE N-NW-0 / (.70).5 (3.75) N-NW-6 3 / 4 (9.05).5 (9.) N-NW-5 (5.40).03 (5.56) N-NW-40 / (38.0).40 (60.96) N-NW-50 (50.80) 3.5 (80.0) NW Full Nipples TUE N-NW-0 / (.70).50 (63.50) N-NW-6 3 / 4 (9.05).30 (58.4) N-NW-5 (5.40) 4.06 (03.) N-NW-40 / (38.0) 4.80 (.9) N-NW-50 (50.80) 6.30 (60.0) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 5

11 SETION. s & Fittings NW Fittings NW Reducer Nipples FLNGE FLNGE TUE NR-NW-6-0 NW-6 NW-0 / (.70).40 (35.56) NR-NW-5-0 NW-5 NW-0 / (.70).40 (35.56) NR-NW-5-6 NW-5 NW-6 3 / 4 (9.05).30 (33.0) NR-NW-40-0 NW-40 NW-0 / (.70).40 (35.56) NR-NW-40-6 NW-40 NW-6 3 / 4 (9.05).30 (33.0) NR-NW-40-5 NW-40 NW-5 (5.40).8 (55.37) NR-NW-50-0 NW-50 NW-0 / (.70).40 (35.56) NR-NW-50-6 NW-50 NW-6 3 / 4 (9.05).30 (33.0) NR-NW-50-5 NW-50 NW-5 (5.40).8 (55.37) NR-NW NW-50 NW-40 / (38.0).55 (64.77) NW onical Reducer Nipples FLNGE FLNGE NR-NW-5-6 NW-5 NW (5.75).57 (39.88) NR-NW-40-6 NW-40 NW (5.75).57 (39.88) NR-NW-50-6 NW-50 NW (5.75).57 (39.88) NR-NW-40-5 NW-40 NW (.0).57 (39.88) NR-NW-50-5 NW-50 NW (.0).57 (39.88) NR-NW NW-50 NW (35.05).57 (39.88) NW 36L onical Reducer Nipples FLNGE FLNGE NR-NW L NW-40 NW (.0).57 (39.88) NR-NW L NW-50 NW (.0).57 (39.88) Typ. NW Tees TUE 3T-NW-0 / (.7).5 (3.75) 3T-NW-6 3 / 4 (9.05).5 (9.) 3T-NW-5 (5.4).03 (5.56) 3T-NW-40 / (38.).40 (60.96) 3T-NW-40H / (38.).56 (65.0) 3T-NW-50 (50.8) 3.5 (80.0) 3T-NW-50H (50.8).76 (70.0) NW Reducer Tees TUE & RM TUE 3 LEG 3TR-NW-5-6 (5.40) 3 / 4 (9.05).03 (5.56).7 (3.6) 3TR-NW-40-6 / (38.0) 3 / 4 (9.05).40 (60.96).53 (38.86) 3TR-NW-40-5 / (38.0) (5.40).40 (60.96).8 (57.9) 3TR-NW-50-6 (50.80) 3 / 4 (9.05) 3.5 (80.0).78 (45.) 3TR-NW (50.80) / (38.0) 3.5 (80.0).65 (67.3) 3 Typ. 6

12 s & Fittings NW Fittings SETION. NW 45 Radius Elbows TUE K-NW-5 (5.40) 0.77 (9.56) K-NW-40 / (38.0).08 (7.43) K-NW-50 (50.80).39 (35.3) NW 45 Radius Elbows with Tangents TUE KL-NW-6 3 / 4 (9.05) 0.9 (3.) KL-NW-5 (5.40). (8.45) KL-NW-40 / (38.0).68 (4.67) KL-NW-50 (50.80).99 (50.55) NW 90 Radius Elbows TUE E-NW-0 / (.70).5 (3.75) 0.75 (9.05) E-NW-6 3 / 4 (9.05).5 (9.).00 (5.40) E-NW-5 (5.40).65 (4.9).50 (38.0) E-NW-40 / (38.0).40 (60.96).5 (57.5) E-NW-40H / (38.0).56 (65.0).5 (57.5) E-NW-40HL / (38.0) 5. (30.05).5 (57.5) E-NW-50 (50.80) 3.5 (80.0) 3.00 (76.0) E-NW-50HL (50.80) 5.5 (39.95) 3.00 (76.0) Typ. Typ. Typ. NW 90 Mitered Elbows TUE E-NW-6M 3 / 4 (9.05).5 (9.) E-NW-5M (5.40).03 (5.56) E-NW-40M / (38.0).40 (60.96) E-NW-40MH / (38.0).56 (65.0) E-NW-50M (50.80) 3.5 (80.0) E-NW-50MH (50.80).76 (70.0) Typ. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 7

13 SETION. s & Fittings NW Fittings Typ. NW 4-Way rosses TUE 4-NW-0 / (.70).5 (3.75) 4-NW-6 3 / 4 (9.05).5 (9.) 4-NW-5 (5.40).03 (5.56) 4-NW-40 / (38.0).40 (60.96) 4-NW-40H / (38.0).56 (65.0) 4-NW-50 (50.80) 3.5 (80.0) 4-NW-50H (50.80).76 (70.0) 3 NW Reducer rosses TUE & TUE 3 & 4 4R-NW-5-6 (5.40) 3 / 4 (9.05).03 (5.56).7 (3.6) 4R-NW-40-6 / (38.0) 3 / 4 (9.05).40 (60.96).53 (38.86) 4R-NW-40-5 / (38.0) (5.40).40 (60.96).8 (57.9) 4R-NW-50-6 (50.80) 3 / 4 (9.05) 3.5 (80.0).78 (45.) 4R-NW (50.80) / (38.0) 3.5 (80.0).65 (67.3) Typ. 4 Typ. 5th Leg Opposite Typ. NW 5-Way rosses TUE 5-NW-6 3 / 4 (9.05).50 (38.0) 5-NW-5 (5.40).03 (5.56) 5-NW-40 / (38.0).40 (60.96) 5-NW-50 (50.80) 3.5 (80.0) Typ. NW 6-Way rosses TUE 6-NW-6 3 / 4 (9.05).50 (38.0) 6-NW-5 (5.40).03 (5.56) 6-NW-40 / (38.0).40 (60.96) 6-NW-50 (50.80) 3.5 (80.0) 6th Leg Opposite Typ. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 8

14 s & Fittings ISO General Information SETION. SPEIFITIONS General: Optional fastener or nonrotatable flanges with clearance bolt holes Nominal sizes: ISO-63 to ISO-500 Tube sizes: / to 0 inches ( mm) Materials : 304 or 36L stainless steel O-rings: FKM, una olts: 8-8 stainless steel Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º una: -30º to 0º Metal seal: -70 to 50 Nor-al Products ISO flanges and hardware are manufactured to the International Standards Organization specification so they can be mated to other manufacturers ISO flanges. ISO flanges are made from rgon Oxygen Decarburization () 304 stainless steel material that is certified to meet STM-40 and has less than 0.0% sulfur in order to prevent sulfur stringers. Grain size is 3 to 6 per STM E-. Maximum inclusion size is.5 per STM E-45. Normally our standard material is in the low carbon range for 304 stainless steel. For increased corrosion resistance, some sizes are available from stock in 36L stainless steel. Optional fastener and nonrotatable ISO flanges are available from stock for / to 0 inch ( mm) tube sizes. oth use a FKM O-ring, held in place by a centering ring, to effect a seal with a vacuum range of 0-8 mbar. ISO components can be baked to 04º. ISO flanges can also be used with standard clamps and aluminum seals to obtain a UHV seal bakeable to 50º. Seals are described in detail in atalog Section.7. ISO ssembly Instructions Optional fastener flanges are joined around the periphery with clamps. Double claw clamps are used when a pair of OF flanges are joined (See diagram.), or single claw clamps are used to join an OF flange to a tapped nonrotatable on a pump or gate valve. (See diagram.) This fastening method allows the OF flange to be rotated for ease of component alignment. dditionally, a rotatable bolt ring can be used to fasten an OF flange to a nonrotatable flange using bolts. (See diagram.) retainer ring prevents the OF flange from slipping through the bolt ring. Nonrotatable ISO flanges are assembled with bolts. (See diagram D.) They do not allow rotation of bolt holes on mating flanges to align components.. Optional Fastener/ Optional Fastener with Double law lamp. Optional Fastener/ Nonrotatable with Rotatable olt Ring and olts. Optional Fastener/ Tapped Nonrotatable with Single law lamp D. Nonrotatable/Nonrotatable with bolts ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 9

15 SETION. s & Fittings ISO s and Hardware ISO Optional Fastener s Seal Side Diagram Diagram D DIGRM NOMINL ID D E ISO OF (95.00) 0.47 (.94) ISO OF / (63.50) 3.74 (95.00) 0.47 (.94).438 (6.93).50 (63.75) 0.5 (6.35) ISO OF (0.0) 0.47 (.94) ISO OF 3 (76.0) 4.33 (0.0) 0.47 (.94).938 (74.63) 3.00 (76.45) 0.5 (6.35) ISO OF (30.00) 0.47 (.94) ISO OF 4 (0.60) 5.8 (30.00) 0.47 (.94) 3.90 (99.3) 4.00 (0.85) 0.5 (6.35) ISO OF (80.00) 0.47 (.94) ISO OF 6 (5.40) (80.0) 0.47 (.94) (49.3) 6.00 (5.9) (9.53) ISO OF (40.00) 0.47 (.94) ISO OF 8 (03.0) (40.00) 0.47 (.94) (00.03) 8.00 (03.7) (9.53) ISO OF -.47 (89.99) 0.47 (.94) ISO OF 0 (54.00).47 (89.99) 0.47 (.94) (50.83) 0.00 (54.5) (9.53) ISO OF (370.00) 0.67 (7.0) ISO OF (304.80) (370.00) 0.67 (7.0).760 (98.70).00 (305.3) (9.53) ISO OF (304.80) (370.00) 0.67 (7.0).40 (35.47).770 (34.36) (9.53) ISO OF (449.99) 0.67 (7.0) ISO OF 6 (406.40) 7.76 (449.99) 0.67 (7.0) 5.64 (396.85) 6.00 (406.9) (9.53) ISO OF (549.99) 0.67 (7.0) ISO OF 0 (508.00).653 (549.99) 0.67 (7.0) 9.64 (498.45) 0.0 (508.5) (9.53) E Seal Side ISO 36L Optional Fastener s DIGRM NOMINL ID D E ISO OF-36L / (63.05) (95.00) 0.47 (.94).438 (6.93).50 (63.75) 0.5 (6.35) ISO OF-36L 3 (76.0) 4.33 (0.0) 0.47 (.94).938 (74.63) 3.00 (76.45) 0.5 (6.35) ISO OF-36L 4 (0.60) 5.8 (30.00) 0.47 (.94) 3.90 (99.3) 4.00 (0.85) 0.5 (6.35) SPEIFITIONS General: Optional fastener or nonrotatable flanges with clearance bolt holes Nominal sizes: ISO-63 to ISO-500 Tube sizes: / to 0 inches ( mm) Materials : 304 or 36L stainless steel O-rings: FKM, una olts: 8-8 stainless steel Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º Silicone: -50º to 30º una: -30º to 0º Metal seal: -70 to 50 ISO Rotatable olt Ring and Retainer Ring FLNGE SIZE ISO-63-R ISO (0.0) 5.8 (30.00) 0.47 (.99) ISO-80-R ISO (4.99) (45.0) 0.47 (.99) ISO-00-R ISO (45.0) (65.00) 0.47 (.99) ISO-60-R ISO (00.00) (4.99) (6.00) ISO-00-R ISO (59.99).0 (84.99) (6.00) ISO-50-R ISO (30.0) 3.89 (335.00) (6.00) ISO-30-R ISO (395.00) 6.73 (44.99) (9.99) ISO-400-R ISO (480.0) (50.0) (9.99) ISO-500-R ISO (580.0) 4.06 (60.0) (9.99) luminum Retaining Ring Replacement Retainer Ring ISO-63-RR ISO-80-RR ISO-00-RR ISO-60-RR ISO-00-RR ISO-50-RR ISO-30-RR ISO-400-RR ISO-500-RR ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. See Section.7 for EV metal seals 30

16 s & Fittings ISO s and Hardware SETION. ISO Nonrotatable s DIGRM NOMINL ID D E F ISO N - ISO-63-50N / (63.50) ISO N - ISO N 3 / (88.90) ISO N - ISO N 4 (0.06) ISO N - ISO N 6 (5.40) ISO N - ISO N 8 (03.0) ISO N - ISO N 0 (54.00) ISO N - ISO-30-00N ISO-30-75N (304.80) (304.80) ISO N - ISO N 6 (406.80) ISO N - ISO N 0 (508.00) 5.8 (30.00) 5.8 (30.00) (45.0) (45.0) (65.00) (65.00) (4.99) (4.99).0 (84.99).0 (84.99) 3.89 (335.00) 3.89 (335.00) 6.73 (44.99) 6.73 (44.99) 6.73 (44.99) (50.0) (50.0) 4.06 (60.0) 4.06 (60.0) ISO olt Kits-Metric -ISO-63 -ISO-80 -ISO-00 -ISO-60 -ISO-00 -ISO-50 -ISO-30 -ISO-400 -ISO (.99) 0.47 (.99) 0.47 (.99) 0.47 (.99) 0.47 (.99) 0.47 (.99) (6.00) (6.00) (6.00) (6.00) (6.00) (6.00) (9.99) (9.99) (9.99) (9.99) (9.99) (9.99) (9.99) (6.93).50 (63.75) 0.50 (6.35) (74.63) 3.00 (76.45) 0.50 (6.35) (99.3) 4.00 (0.85) 0.50 (6.35) (49.3) 6.00 (5.9) (9.53) (00.03) 8.00 (03.7) (9.53) (50.83) 0.00 (54.5) (9.53) (98.70).40 (35.47).00 (305.3).770 (34.36) (9.53) (9.53) (397.3) 6.00 (406.9) (9.53) (498.9) DESRIPTION (4) SS bolts, nuts & washers, M8 x 40mm (8) SS bolts, nuts & washers, M8 x 40mm (8) SS bolts, nuts & washers, M8 x 40mm (8) SS bolts, nuts & washers, M0 x 50mm () SS bolts, nuts & washers, M0 x 50mm () SS bolts, nuts & washers, M0 x 50mm () SS bolts, nuts & washers, M x 60mm (6) SS bolts, nuts & washers, M x 60mm (6) SS bolts, nuts & washers, M x 60mm 0.00 (508.5) (9.53) 4.33 (0.0) 4.33 (0.0) 4.9 (4.99) 4.9 (4.99) (45.0) (45.0) (00.00) (00.00) 0.36 (59.99) 0.36 (59.99).05 (30.0).05 (30.0) 5.55 (395.00) 5.55 (395.00) 5.55 (395.00) (480.0) (480.0).835 (580.0).835 (580.0) OLT HOLES OLT DIMETER (9.) (9.) (9.) (9.) (9.) (9.) (.3) (.3) (.3) (.3) (.3) (.3) 0.55 (4.00) 0.55 (4.00) 0.55 (4.00) (4.00) (4.00) (4.00) (4.00) E Diagram F Diagram D F Seal Side SPEIFITIONS General: Optional fastener or nonrotatable flanges with clearance bolt holes Nominal sizes: ISO-63 to ISO-500 Tube sizes: / to 0 inches ( mm) Materials : 304 or 36L stainless steel O-rings: FKM, una olts: 8-8 stainless steel Vacuum range Elastomer seal: > x 0-8 mbar -High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º una: -30º to 0º Metal seal: -70 to 50 ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. See Section.7 for EV metal seals Seal Side 3

17 SETION. s & Fittings ISO lamps ISO Double law luminum lamps Thread Size FLNGE SIZE THRED SIZE LMPS REQUIRED ISO-63-DP ISO (3.88).96 (49.78) 5 /6-8 4 ISO-80-DP ISO (3.88).96 (49.78) 5 /6-8 8 ISO-00-DP ISO (3.88).96 (49.78) 5 /6-8 8 ISO-60-DP ISO-60.0 (7.94).96 (49.78) 5/6-8 8 ISO-00-DP ISO-00.0 (7.94).96 (49.78) 5 /6-8 ISO-50-DP ISO-50.0 (7.94).96 (49.78) 5 /6-8 ISO-30-DP ISO (34.04).50 (63.50) 7 /6-4 ISO-400-DP ISO (34.04).50 (63.50) 7/6-4 6 ISO-500-DP ISO (34.04).50 (63.50) 7/6-4 6 ISO Single law luminum lamps Thread Size FLNGE SIZE THRED SIZE LMPS REQUIRED ISO-63-SP ISO (3.88).8 (9.97) 0.5 (3.) 5 /6-8 4 ISO-80-SP ISO (3.88).8 (9.97) 0.5 (3.) 5/6-8 8 ISO-00-SP ISO (3.88).8 (9.97) 0.5 (3.) 5/6-8 8 ISO-60-SP ISO-60.0 (7.94).8 (9.97) 0.5 (3.) 5 /6-8 8 ISO-00-SP ISO-00.0 (7.94).8 (9.97) 0.5 (3.) 5 /6-8 ISO-50-SP ISO-50.0 (7.94).8 (9.97) 0.5 (3.) 5 /6-8 ISO-30-SP ISO (34.04).46 (37.08) 0.88 (.35) 7 /6-4 ISO-400-SP ISO (34.04).46 (37.08) 0.88 (.35) 7 /6-4 6 ISO-500-SP ISO (34.04).46 (37.08) 0.88 (.35) 7 /6-4 6 ISO Single law luminum lamps Metric FLNGE SIZE METRI THRED SIZE LMPS REQUIRED ISO-63-SP-M ISO (3.88).0 (30.48) 0.40 (0.6) M8 x.5 4 ISO-80-SP-M ISO (3.88).0 (30.48) 0.40 (0.6) M8 x.5 8 ISO-00-SP-M ISO (3.88).0 (30.48) 0.40 (0.6) M8 x.5 8 ISO-60-SP-M ISO-60.0 (7.94).0 (30.48) 0.40 (0.6) M0 x.50 8 ISO-00-SP-M ISO-00.0 (7.94).0 (30.48) 0.40 (0.6) M0 x.50 ISO-50-SP-M ISO-50.0 (7.94).0 (30.48) 0.40 (0.6) M0 x.50 ISO-30-SP-M ISO (34.04).48 (37.59) 0.79 (0.07) M x.75 ISO-400-SP-M ISO (34.04).48 (37.59) 0.79 (0.07) M x.75 6 ISO-500-SP-M ISO (34.04).48 (37.59) 0.79 (0.07) M x.75 6 ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 3

18 s & Fittings ISO entering Rings SETION. ISO luminum entering Rings with O-ring and luminum Spacer Ring DIGRM O-RING MTERIL ISO-63-R-V* FKM.63 (66.80).74 (69.60) ISO-63-R-* una.63 (66.80).74 (69.60) ISO-80-R-V FKM 3.4 (79.76) 3.5 (8.55) ISO-80-R- una 3.4 (79.76) 3.5 (8.55) ISO-00-R-V FKM 3.89 (98.8) 4.00 (0.60) ISO-00-R- una 3.89 (98.8) 4.00 (0.60) ISO-60-R-V FKM 5.90 (49.86) 6.0 (5.65) ISO-60-R- una 5.90 (49.86) 6.0 (5.65) ISO-00-R-V FKM 8.6 (09.80) 8.37 (.60) ISO-00-R- una 8.6 (09.80) 8.37 (.60) ISO-50-R-V FKM 0.4 (57.56) 0.5 (60.35) ISO-50-R- una 0.4 (57.56) 0.5 (60.35) ISO-30-R-V FKM.3 (3.93).5 (37.75) ISO-30-R- una.3 (3.93).5 (37.75) ISO-400-R-V FKM 5.55 (394.97) 5.75 (400.05) ISO-400-R- una 5.55 (394.97) 5.75 (400.05) ISO-500-R-V FKM 9.53 (496.06) 9.7 (500.89) ISO-500-R- una 9.53 (496.06) 9.7 (500.89).3 (7.95).550 (3.970) Diagram Diagram.0 (5.334).75 (6.985).54 (3.9).4 (5.690) *Machined centering ring. ISO Stainless Steel entering Rings with O-Ring and luminum Spacer Ring DIGRM O-RING MTERIL ISO-63-R-SV FKM.63 (66.80).74 (69.60) ISO-80-R-SV FKM 3.4 (79.76) 3.5 (8.55) ISO-00-R-SV FKM 3.89 (98.8) 4.00 (0.60) ISO-60-R-SV FKM 5.90 (49.86) 6.0 (5.65) ISO-00-R-SV FKM 8.6 (09.80) 8.37 (.60) ISO-50-R-SV FKM 0.4 (57.56) 0.5 (60.35) ISO-30-R-SV FKM.36 (33.94).5 (38.0) ISO-400-R-SV FKM 5.55 (394.97) 5.75 (400.05).3 (7.95).550 (3.970) Diagram Diagram.0 (5.334).75 (6.985).54 (3.9).4 (5.690) ISO 36L Stainless Steel entering Rings with O-Ring and luminum Spacer Ring O-RING MTERIL ISO-63-R-SV-36L FKM.63 (66.80).74 (69.60) ISO-80-R-SV-36L FKM 3.4 (79.76) 3.5 (8.55) ISO-00-R-SV-36L FKM 3.89 (98.8) 4.00 (0.60).3 (7.95).0 (5.334).54 (3.9) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 33

19 SETION. s & Fittings ISO entering Rings Diagram ISO Stainless Steel entering Rings with O-ring.550 (3.970).3 (7.95) Diagram.75 (6.985).4 (5.690).0 (5.334) DIGRM O-RING MTERIL ISO-63-R FKM.63 (66.80).74 (69.60) ISO-80-R FKM 3.4 (79.76) 3.5 (8.55) ISO-00-R FKM 3.89 (98.8) 4.00 (0.60) ISO-60-R FKM 5.90 (49.86) 6.0 (5.65) ISO-00-R FKM 8.6 (09.80) 8.37 (.60) ISO-50-R FKM 0.4 (57.56) 0.5 (60.35) ISO-30-R FKM.3 (3.93).5 (38.0) ISO-400-R FKM 5.55 (394.97) 5.74 (399.80).54 (3.9) See below for replacement O-rings. ISO Screened Stainless Steel entering Rings with O-ring and luminum Spacer Ring.3 (7.95).0 (5.334).54 (3.9) O-RING MTERIL MESH (sq./in.) ISO-63-R-SV-6 FKM.63 (66.80).74 (69.60).38 (60.45) 6 ISO-80-R-SV-6 FKM 3.4 (79.76) 3.5 (8.55).87 (7.90) 6 ISO-00-R-SV-6 FKM 3.89 (98.8) 4.00 (0.60) 3.50 (88.90) 6 ISO-60-R-SV-6 FKM 5.90 (49.86) 6.0 (5.65) 5.50 (39.70) 6 Includes O-ring. See below for replacement O-rings. FKM O-Rings ISO-63-0R-V ISO-80-OR-V ISO-00-OR-V ISO-60-OR-V ISO-00-OR-V ISO-50-OR-V ISO-30-OR-V ISO-400-OR-V ISO-500-OR-V FLNGE TYPE ISO-63 ISO-80 ISO-00 ISO-60 ISO-00 ISO-50 ISO-30 ISO-400 ISO-500 una O-Rings ISO-63-0R- ISO-80-OR- ISO-00-OR- ISO-60-OR- ISO-00-OR- ISO-50-OR- ISO-30-OR- ISO-400-OR- ISO-500-OR- FLNGE TYPE ISO-63 ISO-80 ISO-00 ISO-60 ISO-00 ISO-50 ISO-30 ISO-400 ISO-500 ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 34

20 s & Fittings ISO Fittings SETION. Nor-al Products manufactures a complete line of ISO vacuum fittings with optional fastener or nonrotatable flanges. The fitting tube portions are fabricated from 304 stainless steel. For increased resistance to corrosion in downstream semiconductor processes, some ISO flanges and fittings are available in 36L stainless steel. Elbows, tees and crosses are fabricated in-house using a pulled-port technique for smooth, crevice-free butt welds to provide the maximum in cleanliness for UHV applications. Fittings are shown with optional fastener (OF) flanges only. To order a fitting with nonrotatable flanges substitute -N for -OF in the model number. Fittings are also available with F (onflat style), NW (ISO-KF compatible) and S flanges. Standard finish is bead blasted. Electropolished finish also available. all for pricing. SPEIFITIONS General: Optional fastener or nonrotatable flanges with clearance bolt holes Nominal sizes: ISO-63 to ISO-500 Tube sizes: / to 0 inches ( mm) Tube finish: eadblast, tumbled, or electropolish Materials : 304 or 36L stainless steel O-rings: FKM, una olts: 8-8 stainless steel Vacuum range Elastomer seal: > x 0-8 mbar - High vacuum Metal seal: > x 0 - mbar - UHV Temperature range FKM: -0º to 00º una: -30º to 0º Metal seal: -70 to 50 See Section.7 for EV metal seals ISO 90 Mitered Elbows TUE E-ISO-63-OF-M / (63.50) 3.5 (8.55) E-ISO-80-OF-M 3 (76.0) 3.50 (88.90) E-ISO-00-OF-M 4 (0.60) 4.3 (04.90) E-ISO-60-OF-M 6 (5.40) 5.38 (36.65) E-ISO-00-OF-M 8 (03.0) 7.38 (87.45) E-ISO-50-OF-M 0 (54.00) 9.88 (50.95) ISO 90 Radius Elbows TUE E-ISO-63-OF / (63.50) 4.00 (0.60) 3.75 (95.5) E-ISO-80-OF 3 (76.0) 4.75 (0.65) 4.50 (4.30) E-ISO-00-OF 4 (0.60) 6.5 (58.75) 6.00 (5.40) E-ISO-60-OF 6 (5.40) 9.38 (38.5) 9.00 (8.60) E-ISO-00-OF 8 (03.0).38 (34.45).00 (304.80) E-ISO-50-OF 0 (54.00) 5.38 (390.65) 5.00 (38.00) ISO 45 Elbows with Tangents TUE KL-ISO-63-OF / (63.50) 3.5 (8.55) KL-ISO-80-OF 3 (76.0) 3.93 (99.8) KL-ISO-00-OF 4 (0.60) 5.03 (7.76) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 35

21 SETION. s & Fittings ISO Fittings ISO Half Nipples TUE N-ISO-63-OF / (63.50) 3.5 (8.55) N-ISO-63-OF-V / (63.50) 4.00 (0.60) N-ISO-63-OF-H / (63.50) 3.94 (00.08) N-ISO-80-OF 3 (76.0) 3.50 (88.90) N-ISO-80-OF-H 3 (76.0) 3.94 (00.08) N-ISO-00-OF 4 (0.60) 4.3 (04.90) N-ISO-00-OF-V 4 (0.60) 5. (30.05) N-ISO-00-OF-H 4 (0.60) 3.94 (00.08) N-ISO-60-OF 6 (5.40) 5.38 (36.65) N-ISO-60-OF-V 6 (5.40) 6.44 (63.58) N-ISO-60-OF-H 6 (5.40) 3.94 (00.08) N-ISO-00-OF 8 (03.0) 7.38 (87.45) N-ISO-50-OF 0 (54.00) 9.88 (50.95) N-ISO-30-OF (304.80) 9.88 (50.95) N-ISO-400-OF 6 (406.40) 9.88 (50.95) N-ISO-500-OF 0 (508.00) 9.88 (50.95) ISO 36L Half Nipples TUE N-ISO-63-OF-36L / (63.50) 3.5 (8.55) N-ISO-80-OF-36L 3 (76.0) 3.50 (88.90) N-ISO-00-OF-36L 4 (0.60) 4.3 (04.90) ISO Full Nipples TUE N-ISO-63-OF / (63.50) 6.50 (65.0) N-ISO-80-OF 3 (76.0) 7.00 (77.80) N-ISO-00-OF 4 (0.60) 8.6 (09.80) N-ISO-60-OF 6 (5.40) 0.76 (73.30) N-ISO-00-OF 8 (03.0) 4.76 (374.90) N-ISO-50-OF 0 (54.00) 9.76 (50.90) N-ISO-30-OF (304.80) 9.76 (50.90) N-ISO-400-OF 6 (406.40) 9.76 (50.90) N-ISO-500-OF 0 (508.00) 9.76 (50.90) ISO Reducer Nipples 3.00 FLNGE FLNGE TUE NR-ISO OF ISO-80 ISO-63 / (63.50) NR-ISO OF ISO-00 ISO-63 / (63.50) NR-ISO OF ISO-00 ISO-80 3 (76.0) NR-ISO OF ISO-60 ISO-63 / (63.50) NR-ISO OF ISO-60 ISO-80 3 (76.0) NR-ISO OF ISO-60 ISO-00 4 (0.60) NR-ISO OF ISO-00 ISO-63 / (63.50) NR-ISO OF ISO-00 ISO-80 3 (76.0) NR-ISO OF ISO-00 ISO-00 4 (0.60) NR-ISO OF ISO-00 ISO-60 6 (5.40) NR-ISO OF ISO-50 ISO-63 / (63.50) NR-ISO OF ISO-50 ISO-80 3 (76.0) NR-ISO OF ISO-50 ISO-00 4 (0.60) NR-ISO OF ISO-50 ISO-60 6 (5.40) NR-ISO OF ISO-50 ISO-00 8 (03.0) ISO onical Reducer Nipples FLNGE FLNGE TYPE TUE TYPE TUE NR-ISO OF ISO-80 3 (76.) ISO-63 / (63.50) 4. (04.65) NR-ISO OF ISO-00 4 (0.6) ISO-63 / (63.50) 4. (04.65) NR-ISO OF ISO-00 4 (0.6) ISO-80 3 (76.0) 4. (04.65) 36

22 s & Fittings ISO Fittings SETION. ISO Tees ISO Reducer Tees FLNGE & FLNGE 3 TYPE RM TYPE LEG 3TR-ISO OF ISO-80 3 (76.) ISO-63 / (63.50) 3.50 (88.90) 3.50 (88.90) 3TR-ISO OF ISO-00 4 (0.6) ISO-63 / (63.50) 4.3 (04.90) 4.00 (0.60) 3TR-ISO OF ISO-00 4 (0.6 ISO-80 3 (76.0) 4.3 (04.90) 4.00 (0.60) 3TR-ISO OF ISO-60 6 (5.4) ISO-63 / (63.50) 5.38 (36.65) 5.00 (7.00) 3TR-ISO OF ISO-60 6 (5.4) ISO-80 3 (76.0) 5.38 (36.65) 5.00 (7.00) 3TR-ISO OF ISO-60 6 (5.4) ISO-00 4 (0.60) 5.38 (36.65) 5.3 (30.30) 3TR-ISO OF ISO-00 8 (03.) ISO-63 / (63.50) 7.38 (87.45) 6.00 (5.40) 3TR-ISO OF ISO-00 8 (03.) ISO-80 3 (76.0) 7.38 (87.45) 6.00 (5.40) 3TR-ISO OF ISO-00 8 (03.) ISO-00 4 (0.60) 7.38 (87.45) 6.3 (55.70) 3TR-ISO OF ISO-00 8 (03.) ISO-60 6 (5.40) 7.38 (87.45) 6.38 (6.05) TUE 3T-ISO-63-OF / (63.50) 3.5 (8.55) 3T-ISO-80-OF 3 (76.0) 3.50 (88.90) 3T-ISO-00-OF 4 (0.60) 4.3 (04.90) 3T-ISO-60-OF 6 (5.40) 5.38 (36.65) 3T-ISO-00-OF 8 (03.0) 7.38 (87.45) 3T-ISO-50-OF 0 (54.00) 9.88 (50.95) 3 Typ. Typ. Typ. Typ. ISO 4-Way rosses TUE 4-ISO-63-OF / (63.50) 3.5 (8.55) 4-ISO-80-OF 3 (76.0) 3.50 (88.90) 4-ISO-00-OF 4 (0.60) 4.3 (04.90) 4-ISO-60-OF 6 (5.40) 5.38 (36.65) 4-ISO-00-OF 8 (03.0) 7.38 (87.45) 4-ISO-50-OF 0 (54.00) 9.88 (50.95) ISO 4-Way Reducer rosses 3 FLNGES & FLNGES 3 & 4 TYPE RM TYPE LEG 4R-ISO OF ISO-80 3 ISO-63 / (63.50) 3.50 (88.90) 3.50 (88.90) 4R-IS OF ISO-00 4 IS0-63 / (63.50) 4.3 (04.90) 4.00 (0.60) 4R-ISO OF ISO-00 4 IS (76.0) 4.3 (04.90) 4.00 (0.60) 4R-ISO OF IS ISO-63 / (63.50) 5.38 (36.65) 5.00 (7.00) 4R-ISO OF ISO-60 6 ISO-80 3 (76.0) 5.38 (36.65) 5.00 (7.00) 4R-ISO OF ISO-60 6 ISO-00 4 (0.60) 5.38 (36.65) 5.3 (30.30) 4R-ISO OF ISO-00 8 ISO-60 6 (5.40) 7.38 (87.45) 6.38 (6.05) 4 Typ. Typ. 5th Leg Opposite Typ. Typ. ISO 5-Way rosses TUE 5-ISO-63-OF / (63.50) 3.5 (8.55) 5-ISO-80-OF 3 (76.0) 3.50 (88.90) 5-ISO-00-OF 4 (0.60) 4.3 (04.90) 5-ISO-60-OF 6 (5.40) 5.38 (36.65) 5-ISO-00-OF 8 (03.0) 7.38 (87.45) 5-ISO-50-OF 0 (54.00) 9.88 (50.95) ISO 6-Way rosses TUE 6-ISO-63-OF / (63.50) 3.5 (8.55) 6-ISO-80-OF 3 (76.0) 3.50 (88.90) 6-ISO-00-OF 4 (0.60) 4.3 (04.90) 6-ISO-60-OF 6 (5.40) 5.38 (36.65) 6-ISO-00-OF 8 (03.0) 7.38 (87.45) 6-ISO-50-OF 0 (54.00) 9.88 (50.95) 6th Leg Opposite Typ. Typ. 37

23 SETION.3 s & Fittings S General Information SPEIFITIONS General: Rotatable or nonrotatable flanges Nominal sizes: 5 to 6 inches (5-400mm) Tube sizes: to inches (50-30mm) Materials : 304 stainless steel O-rings: FKM olts: 8-8 stainless steel Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 04º Sustained: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Rotatable S Nor-al Products S flanges are manufactured from specially treated 304 stainless steel. These flanges mate with standard 50 lb. S flanges or 50 NSI flanges. They are available from stock for standard tube sizes from to inches (50.8 to 304.8mm). Larger sizes are available upon request. S TO NSI ONVERSION HRT S NSI Nuts and bolts are used to apply pressure between the mating flanges and a seal is effected when a FKM O-ring Receiver Insert O-ring is compressed. S flanges can be baked to 04 and have a vacuum range of up to 0-8 mbar. esides being sold separately, they are available as standards on nipples, adapters, tees, crosses, elbows and valves. Rotatable Option When components of several systems are used interchangeably, use of rotatable flanges is recommended. ssembly is facilitated by rotation of mating flanges, to align bolt holes. Nonrotatable S flanges, unlike rotatable, contain both sealing surface and bolt holes in one unit rather than two. This makes the nonrotatable flange less expensive, and therefore the preferred choice when mating component orientation is not a Nonrotatable S with O-ring Groove concern. ll fittings are priced with nonrotatable flanges. For fittings with rotatable flanges, add the difference between a nonrotatable and rotatable flange of the desired size. Multiply by the number of rotatable flanges required. e sure to specify the flange numbers which are rotatable. O-Ring Groove Option One of each pair of mating S flanges requires an O-ring groove. When ordering flanges with grooves indicate this by adding -G to the flange model number. n example would be a rotatable S- flange bored out for six inch (5.4mm) tubing with a groove. The model number would be S--600R-G. The same rule applies when ordering a fitting or adapter flange with only one S flange. n example would be adapter flange model number S Z-G. When a fitting has more than one S flange, such as a four-way cross, indicate which flanges are desired with grooves by using the flange numbers on the drawing. If, for example, you desired a cross with S-9 flanges and a six inch (60mm) tube with grooved flanges on the left and bottom ports, the model number would be 4-S G-G3. dd the appropriate amount for each O-ring groove to the price of the fitting. 38

24 s & Fittings S s & Hardware SETION.3 S s - 5 to 9 Inch (5-5mm) One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. TYPE DIGRM D E OLT HOLES NO. SIZE S-5-000N lank 5.00 (7.00) (.70) (98.55) (5.8) S-5-00N ored (7.00) (.70).0 (5.05).938 (49.3) (98.55) (5.8) S-5-50N ored (7.00) (.70).5 (63.75).438 (6.93) (98.55) (5.8) S-5-000R lank 5.00 (7.00) (.70) (98.55) (5.8) S-5-00R ored (7.00) (.70).0 (5.05).938 (49.3) (98.55) (5.8) S-5-50R ored (7.00) (.70).5 (63.75).438 (6.93) (98.55) (5.8) S-6-000N lank 6.00 (5.40) (.70) (0.65) (9.05) S-6-300N ored (5.40) (.70) 3.0 (76.45).938 (74.63) (0.65) (9.05) S-6-350N ored (5.40) (.70) 3.5 (89.5) (87.33) (0.65) (9.05) S-6-000R lank 6.00 (5.40) 0.6 (5.54) (0.65) (9.05) S-6-300R ored (5.40) 0.6 (5.54) 3.0 (76.45).938 (74.63) (0.65) (9.05) S-6-350R ored (5.40) 0.6 (5.54) 3.5 (89.5) (87.33) (0.65) (9.05) S N lank 7.50 (90.50) (.70) (5.40) (9.05) S N ored (90.50) (.70) 4.0 (0.85) 3.90 (99.3) (5.40) (9.05) S R lank 7.50 (90.50) 0.6 (5.54) (5.40) (9.05) S R ored (90.50) 0.6 (5.54) 4.0 (0.85) 3.90 (99.3) (5.40) (9.05) S-9-000N lank 9.00 (8.60) (.70) (90.50) (9.05) S-9-400N ored (8.60) (.70) 4.0 (0.85) 3.90 (99.3) (90.50) (9.05) S-9-600N ored (8.60) (.70) 6.0 (5.9) (49.3) (90.50) (9.05) S-9-000R lank 9.00 (8.60) 0.6 (5.54) (90.50) (9.05) S-9-400R ored (8.60) 0.6 (5.54) 4.0 (0.85) 3.90 (99.3) (90.50) (9.05) S-9-600R ored (8.60) 0.6 (5.54) 6.0 (5.9) (49.3) (90.50) (9.05) Model Number Definitions N = Nonrotatable R = Rotatable O-ring Groove Option Indicate grooved flanges by adding -G to the end of the main part number. dd the appropriate cost for each grooved flange. Example: S-9-000R-G.50 (6).50 (6) Optional O-ring Groove Optional O-ring Groove Optional O-ring Groove Optional O-ring Groove Diagram E Diagram E Diagram 3 E D Diagram 4 E D S Hardware FLNGE SIZE DESRIPTION -5 S-5 (4) SS bolts ( 9 /6- x.5) nuts and washers OR--3 S-5 () FKM O-ring -6 S-6 (4) SS bolts ( 5 /8- x.5) nuts and washers OR--38 S-6 () FKM O-ring -7.5 S-7.5 (4) SS bolts ( 5 /8- x.5) nuts and washers OR--43 S-7.5 () FKM O-ring -9 S-9 (8) SS bolts ( 5 /8- x.5) nuts and washers OR--59 S-9 () FKM O-ring SPEIFITIONS General: Rotatable and nonrotatable Materials s: 304 stainless steel Gaskets: FKM olts: 8-8 stainless steel Torque:.5 Nm Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 04º Sustained: -0º to 50º S Hardware for Mating to Gate Valves FLNGE SIZE DESRIPTION -6GV S-6 (4) SS bolts ( 3 /8-6x.0) & reducer bushings ( 3 /8 x 3 /4) -7.5GV S-7.5 (4) SS bolts ( 3 /8-6x.0) & reducer bushings ( 3 /8 x 3 /4) -9GV S-9 (8) SS bolts ( 3 /8-6x.0) & reducer bushings ( 3 /8 x 3 /4) 39

25 SETION.3 s & Fittings S s & Hardware Optional O-ring Groove Optional O-ring Groove.375 Optional O-ring Groove.375 Optional O-ring Groove Diagram D Diagram D Diagram 3 D Diagram 4 D.750 (9.050).750 (9.050).750 (9.050).750 (9.050) S s - to 6 Inch (85-400mm) One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. TYPE DIGRM D OLT HOLES NO. SIZE S--000N lank.00 (79.40) (5.3) (0.6) S--600N ored 3.00 (79.40) 6.0 (5.9) (49.5) (5.3) (0.6) S--800N ored 3.00 (79.40) 8.0 (03.7) (00.05) (5.3) (0.6) S--000R lank.00 (79.40) (5.3) (0.6) S--600R ored 4.00 (79.40) 6.0 (5.9) (49.5) (5.3) (0.6) S--800R ored 4.00 (79.40) 8.0 (03.7) (00.05) (5.3) (0.6) S N lank 3.50 (343.90) (98.45) (0.6) S N ored (343.90) 8.0 (03.7) (00.05).750 (98.45) (0.6) S N ored (343.90) 0.03 (54.76) (50.85).750 (98.45) (0.6) S R lank 3.50 (343.90) (98.45) (0.6) S R ored (343.90) 8.0 (03.7) (00.05).750 (98.45) (0.6) S R ored (343.90) 0.03 (54.76) (50.85).750 (98.45) (0.6) S-6-000N lank 6.00 (406.40) (36.95) 0.8 (0.6) S-6-000N ored (406.40) 0.03 (54.76) (50.85) 4.50 (36.95) 0.8 (0.6) S-6-00N ored (406.40).03 (305.56).875 (30.65) 4.50 (36.95) 0.8 (0.6) S-6-000R lank 6.00 (406.40) (36.95) 0.8 (0.6) S-6-000R ored (406.40) 0.03 (54.76) (50.85) 4.50 (36.95) 0.8 (0.6) S-6-00R ored (406.40).03 (305.56).875 (30.65) 4.50 (36.95) 0.8 (0.6) Model Number Definitions N = Nonrotatable R = Rotatable O-ring Groove Option Indicate grooved flanges by adding -G to the end of the main part number. dd the appropriate cost for each grooved flange. Example: S-9-000R-G SPEIFITIONS General: Rotatable and nonrotatable Material s: 304 stainless steel Gaskets: FKM olts: 8-8 stainless steel Torque:.5 Nm Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0 to 04º Operating: -0º to 50º S Hardware SIZE DESRIPTION - S- (8) SS bolts ( 3 /4-0 x.5) nuts and washers OR--66 S- () FKM O-ring -3.5 S-3.5 (8) SS bolts ( 3 /4-0 x.5) nuts and washers OR--74 S-3.5 () FKM O-ring -6 S-6 () SS bolts ( 3 /4-0 x.5) nuts and washers OR--78 S-6 () FKM O-ring S Hardware for Mating to Gate Valves SIZE DESRIPTION -GV S- (8) SS bolts ( 3 /8-6 x.0) -6GV S-6 () SS bolts ( 3 /8-6 x.0) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 40

26 s & Fittings S Fittings SETION.3 Nor-al Products manufactures a complete line of flanged vacuum component fittings. The tube portions are fabricated from 304 stainless steel. On request, 36 stainless steel can be supplied. Nor-al Products makes its own elbows, and all tees and crosses are made with the pulled-port technique. This allows smooth, crevice-free butt welds to provide the maximum in cleanliness for UHV applications. ake-out range is up to 00. Nor-al Products fittings are also available with F (onflat style), NW and ISO flanges. S Half Nipples One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE N-S (7.00) (50.80) 3.5 (8.55) N-S (7.00) / (63.50) 3.5 (8.55) N-S-5-50V 5.00 (7.00) / (63.50) 4.00 (0.60) N-S (5.40) 3 (76.0) 3.50 (88.90) N-S (90.50) 4 (0.60) 4.3 (04.90) N-S V 7.50 (90.50) 4 (0.60) 5. (30.05) N-S (8.60) 4 (0.60) 4.3 (04.90) N-S-9-400V 9.00 (8.60) 4 (0.60) 5. (30.05) N-S (8.60) 6 (5.40).5 (33.35) N-S-9-600V 9.00 (8.60) 6 (5.40) 6.3 (60.7) N-S (79.40) 6 (5.40) 5.38 (36.65) N-S--600V.00 (79.40) 6 (5.40) 6.44 (63.58) N-S (79.40) 8 (03.0) 7.38 (87.45) N-S (34.90) 8 (03.0) 7.75 (96.85) N-S (34.90) 0 (54.00) 9.88 (50.95) N-S (406.40) 0 (54.00) 9.88 (50.95) N-S (406.40) (304.80) 9.88 (50.95) S Full Nipples One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE N-S-5-00N 5.00 (7.00) (50.80) 6.50 (65.0) N-S-5-50N 5.00 (7.00) / (63.50) 6.50 (65.0) N-S-5-50NV 5.00 (7.00) / (63.50) 8.00 (03.0) N-S-6-300N 6.00 (5.40) 3 (76.0) 7.00 (77.80) N-S N 7.50 (90.50) 4 (0.60) 8.6 (09.80) N-S NV 7.50 (90.50) 4 (0.60) 0.4 (60.0) N-S-9-400N 9.00 (8.60) 4 (0.60) 8.6 (09.80) N-S-9-400NV 9.00 (8.60) 4 (0.60) 0.4 (60.0) N-S-9-600N 9.00 (8.60) 6 (5.40) 0.50 (66.70) N-S-9-600NV 9.00 (8.60) 6 (5.40).6 (30.55) N-S--600N.00 (79.40) 6 (5.40) 0.76 (73.30) N-S--600NV.00 (79.40) 6 (5.40).88 (37.5) N-S--800N.00 (79.40) 8 (03.0) 4.76 (374.90) N-S N 3.50 (34.90) 8 (03.0) 5.50 (393.70) N-S N 3.50 (34.90) 0 (54.00) 9.76 (50.90) N-S-6-000N 6.00 (406.40) 0 (54.00) 9.76 (50.90) N-S-6-00N 6.00 (406.40) (304.80) 9.76 (50.90) TUE TUE SPEIFITIONS General: Rotatable and nonrotatable Materials s: 304 stainless steel Gaskets: FKM olts: 8-8 stainless steel Torque:.5 Nm Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 04º Sustained: -0º to 50º O-ring Groove Option Indicate grooved flanges by adding -G + number from drawing to the end of main part number. dd the appropriate cost for each grooved flange. Example: 4-S G-G3 4

27 SETION.3 s & Fittings S Fittings 5.00 S Reducer Nipples One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE FLNGE NR-S-9-5-N S-9 S-5 (50.80) NR-S-9-6-N S-9 S-6 3 (76.0) NR-S N S-9 S (0.60) NR-S--5-N S- S-5 (50.80) NR-S--6-N S- S-6 3 (76.0) NR-S--7.5-N S- S (0.60) NR-S--9-N S- S-9 6 (5.40) NR-S N S-3.5 S-5 (50.80) NR-S N S-3.5 S-6 3 (76.0) NR-S N S-3.5 S (0.60) NR-S N S-3.5 S-9 6 (5.40) NR-S-3.5--N S-3.5 S- 8 (03.0) NR-S-6-5-N S-6 S-5 (50.80) NR-S-6-6-N S-6 S-6 3 (76.0) NR-S N S-6 S (0.60) NR-S-6-9-N S-6 S-9 6 (5.40) NR-S-6--N S-6 S- 8 (03.0) NR-S N S-6 S (54.00) TUE 4. onical Reducer Nipples One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE SIZE FLNGE TUE FLNGE SIZE FLNGE TUE NR-S-6-5-N S-6 3 (76.0) S-5 (50.80) NR-S N S (0.60) S-5 (50.80) NR-S N S (0.60) S-6 3 (76.0) S 45º Radius Elbows with Tangents One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE KL-S-5-N 5.00 (7.00) (50.80).09 (53.09) KL-S-6-N 6.00 (5.40) 3 (76.0) 3.93 (99.8) KL-S-7.5-N 7.50 (90.50) 4 (0.60) 5.0 (7.5) KL-S-9-N 9.00 (8.60) 4 (0.60) 5.0 (7.5) TUE O-ring Groove Option Indicate grooved flanges by adding -G + number from drawing to the end of main part number. dd the appropriate cost for each grooved flange. Example: 4-S G-G3 ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 4

28 s & Fittings S Fittings SETION.3 S 90 Radius Elbows One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE TUE E-S-5-N 5.00 (7.0) (50.80) 3.5 (8.55) 3 (76.0) E-S-6-N 6.00 (5.4) 3 (76.0) 4.75 (0.65) 4 / (4.30) E-S-9-N 9.00 (8.6) 4 (0.60) 6.5 (58.75) 6 (5.40) E-S--N.00 (79.4) 6 (5.40) 9.38 (38.5) 9 (8.60) E-S-3.5-N 3.50 (34.9) 8 (03.0).38 (34.45) (304.80) E-S-6-N 6.00 (406.4) 0 (54.00) 5.38 (390.65) 5 (38.00) S 90 Mitered Elbows One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE E-S-5-00NM 5.00 (7.00) (50.80) 3.5 (8.55) E-S-5-50NM 5.00 (7.00) / (63.50) 3.5 (8.55) E-S-5-50NMV 5.00 (7.00) / (63.50) 4.00 (0.60) E-S NMV 7.50 (90.50) 4 (0.60) 5. (30.05) E-S-9-400NMV 9.00 (8.60) 4 (0.60) 5. (30.05) E-S-9-600NM 9.00 (8.60) 6 (5.40) 5.5 (33.35) E-S-9-600NMV 9.00 (8.60) 6 (5.40) 6.3 (60.7) E-S--600NMV.00 (79.40) 6 (5.40) 6.44 (63.58) E-S--800NM.00 (79.40) 8 (03.0) 7.38 (87.45) E-S NM 3.50 (34.90) 8 (03.0) 7.75 (96.85) E-S NM 3.50 (34.90) 0 (54.00) 9.88 (50.95) E-S-6-000NM 6.00 (406.40) 0 (54.00) 9.88 (50.95) TUE S Tees One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. FLNGE 3T-S-5-00N 5.00 (7.00) (50.80) 3.5 (8.55) 3T-S-5-50N 5.00 (7.00) / (63.50) 3.5 (8.55) 3T-S-5-50NV 5.00 (7.00) / (63.50) 4.00 (0.60) 3T-S NV 7.50 (90.50) 4 (0.60) 5. (30.05) 3T-S-9-400NV 9.00 (8.60) 4 (0.60) 5. (30.05) 3T-S-9-600N 9.00 (8.60) 6 (5.40) 5.5 (33.35) 3T-S-9-600NV 9.00 (8.60) 6 (5.40) 6.3 (60.7) 3T-S--600NV.00 (79.40) 6 (5.40) 6.44 (63.58) 3T-S--800N.00 (79.40) 8 (03.0) 7.38 (87.45) 3T-S N 3.50 (34.90) 8 (03.0) 7.75 (96.85) 3T-S N 3.50 (34.90) 0 (54.00) 9.88 (50.95) 3T-S-6-000N 6.00 (406.40) 0 (54.00) 9.88 (50.95) TUE 3 O-ring Groove Option Indicate grooved flanges by adding -G + number from drawing to the end of main part number. dd the appropriate cost for each grooved flange. Example: 4-S G-G3 43

29 SETION.3 s & Fittings S Fittings 4 S 4-Way rosses One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. 3 Typ. Typ. FLNGE 4-S-5-00N 5.00 (7.00) (50.80) 3.5 (8.55) 4-S-5-50N 5.00 (7.00) / (63.50) 3.5 (8.55) 4-S-5-50NV 5.00 (7.00) / (63.50) 4.00 (0.60) 4-S NV 7.50 (90.50) 4 (0.60) 5. (30.05) 4-S-9-400NV 9.00 (8.60) 4 (0.60) 5. (30.05) 4-S-9-600N 9.00 (8.60) 6 (5.40) 5.5 (33.35) 4-S-9-600NV 9.00 (8.60) 6 (5.40) 6.3 (60.7) 4-S--600NV.00 (79.40) 6 (5.40) 6.44 (63.58) 4-S--800N.00 (79.40) 8 (03.0) 7.38 (87.45) 4-S N 3.50 (34.90) 8 (03.0) 7.75 (96.85) 4-S N 3.50 (34.90) 0 (54.00) 9.88 (50.95) 4-S-6-000N 6.00 (406.40) 0 (54.00) 9.88 (50.95) TUE 4 S 5-Way rosses One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. 5 3 Typ. Typ. FLNGE 5-S-5-00N 5.00 (7.00) (50.80) 3.5 (8.55) 5-S-5-50N 5.00 (7.00) / (63.50) 3.5 (8.55) 5-S-5-50NV 5.00 (7.00) / (63.50) 4.00 (0.60) 5-S NV 7.50 (90.50) 4 (0.60) 5. (30.05) 5-S-9-400NV 9.00 (8.60) 4 (0.60) 5. (30.05) 5-S-9-600N 9.00 (8.60) 6 (5.40) 5.5 (33.35) 5-S-9-600NV 9.00 (8.60) 6 (5.40) 6.3 (60.7) 5-S--600NV.00 (79.40) 6 (5.40) 6.44 (63.58) 5-S--800N.00 (79.40) 8 (03.0) 7.38 (87.45) 5-S N 3.50 (34.90) 8 (03.0) 7.75 (96.85) 5-S N 3.50 (34.90) 0 (54.00) 9.88 (50.95) 5-S-6-000N 6.00 (406.40) 0 (54.00) 9.88 (50.95) TUE 6 (other side) 4 S 6-Way rosses One of each pair of mating S flanges requires an O-ring groove. To specify grooved flanges refer to the instructions below. 5 3 Typ. Typ. FLNGE 6-S-5-00N 5.00 (7.00) (50.80) 3.5 (8.55) 6-S-5-50N 5.00 (7.00) / (63.50) 3.5 (8.55) 6-S-5-50NV 5.00 (7.00) / (63.50) 4.00 (0.60) 6-S NV 7.50 (90.50) 4 (0.60) 5. (30.05) 6-S-9-400NV 9.00 (8.60) 4 (0.60) 5. (30.05) 6-S-9-600N 9.00 (8.60) 6 (5.40) 5.5 (33.35) 6-S-9-600NV 9.00 (8.60) 6 (5.40) 6.3 (60.7) 6-S--600NV.00 (79.40) 6 (5.40) 6.44 (63.58) 6-S--800N.00 (79.40) 8 (03.0) 7.38 (87.45) 6-S N 3.50 (34.90) 8 (03.0) 7.75 (96.85) 6-S N 3.50 (34.90) 0 (54.00) 9.88 (50.95) 6-S-6-000N 6.00 (406.40) 0 (54.00) 9.88 (50.95) TUE ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. O-ring Groove Option Indicate grooved flanges by adding -G + number from drawing to the end of main part number. dd the appropriate cost for each grooved flange. Example: 4-S G-G3 44

30 SETION.4 s & Fittings F General Information SPEIFITIONS General: Rotatable or nonrotatable with tapped or clearance bolt holes Nominal sizes: /3 to 6 / inches (34-49mm) Tube sizes: /4 to 4 inches (6-350mm) Materials : 304 stainless steel (36L available on request) Gaskets: FKM, copper or silver plated olts: 8-8 stainless steel or silver plated Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Nor-al Products onflat (F) flanges are compatible with other onflat style flanges and are available in sizes from /3 to 6 / inch ( mm) for /4 to 4 inch ( mm) tube diameters. Normally our standard material is in the low carbon range for 304. s are made from 304 that has been specially treated to remove impurities inherent in 300 series steels. Special UHV flanges 4 ½ inches (4.3mm) and smaller can be made from 304 electroslag remelt (ESR) bar stock. ESR is a refining process that produces stainless steel with higher purity, fewer inclusions and more uniform grain structure to eliminate microscopic leak paths. Our standard flange material is certified to meet STM -40 and has less than 0.0% sulfur to prevent sulfur stringers. Grain size is 3 to 6 per STM E-. Maximum inclusion size is.5 per STM E-45. s specials, 304L and 36L material can be supplied in roll-forged rings. Machining is consistent with good UHV practice. Machine coolant is sulfur free to reduce outgassing. State-of-the-art N machine centers are used to produce flanges with consistent high quality. s are machine washed in approved aqueous detergent after machining. hem-cleaning and clean room packaging are available. F flanges utilize OFH opper Gasket an OFH copper gasket to produce a vacuum tight seal up to 0-3 mbar, even when baked repeatedly to 450º. When the copper gasket is compressed between the knife edges of F flanges, its material flows laterally to fill surface imperfections. Nor-al Products offers F flanges in rotatable as well as nonrotatable versions. (Refer to diagram on page 46.) When components of several systems are used interchangeably, the use of rotatable flanges is recommended. ssembly is facilitated by rotating the receiver portion of the flange to align its bolt holes with those of the mating flange. The insert is welded to the tube or component and contains the knife edge portion of the F flange. Nonrotatable F flanges, unlike rotatable, contain both sealing surface and bolt holes in one unit. This makes the nonrotatable flange less expensive, and therefore the preferred choice when mating component orientation is not a concern. ll fittings are priced with a rotatable flange opposing a nonrotatable. For fittings with all nonrotatable flanges subtract the difference in price between a rotatable and nonrotatable flange of the desired size multiplied by the number of additional nonrotatable flanges. Metric s and Hardware Nor-al Products now stocks bored metric tapped F flanges in 3 /4, 4 /, 6, 8 and 0 inch (69.85, 4.3, 5.5, 03. and 54mm) s. Other sizes are available upon request. Fasteners for metric flanges are stocked for each flange size. Silver plated Gaskets and olts We are now offering silver plated copper gaskets and bolt kits in a variety of sizes. Silver plated copper gaskets are recommended when the use of pure copper is unacceptable. Silver plated bolt kits offer an alternative to using anti-seize thread lubricant. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 45

31 SETION.4 s & Fittings F ssembly Instructions SPEIFITIONS General: Rotatable or nonrotatable flanges with tapped or clearance bolt holes Nominal sizes: /3 to 6 / inches (34-49mm) Tube sizes: /4 to 4 inches ( mm) Materials : 304 stainless steel (36L available on request) Gaskets: FKM, copper or silver plated olts: 8-8 stainless steel or silver plated Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Plate Nut Nut Nonrotatable Receiver Insert Gasket Rotatable Fastening Hardware F flanges are available with tapped or untapped holes. Tapped flanges are available in UN/UNF or metric threads. Tapped flanges have through holes, so bolts may protrude slightly from the back of the flange when fastened to an untapped flange. Untapped F flanges can be fastened to each other with stainless steel bolts and hex nuts or plate nuts. Plate nuts center themselves over two adjacent holes and can be held in place with one finger while the bolts are tightened. They are available for most flange sizes from /3 to 0 inch ( mm) s. s an alternative to hex head bolts, -point bolts are available for F flanges from 3 /4 to 0 inch (33.96 to 354mm) s. Silver plated bolts eliminate the need for anti-seize compound in clean room environments. ssembly Instructions for Nor-al F (onflat) s. pply a small amount of high temperature anti-seize compound to the bolt threads.. heck that both flange surfaces are clean and sealing edges are free from nicks and scratches. 3. Using clean, lint free gloves, unpack gasket. 4. Place gasket in the knife edge counterbore of nonrotatable flange. 5. lign the mating hole pattern and leak test grooves. 6. Install the proper bolts and tighten hand tight. heck to see that the flange faces are parallel. 7. Tighten the bolts /4 to / turns using a star pattern until the flange faces are metal to metal. 8. Torque the fasteners to the listed value using the same pattern. Torque Specifications * NOMINL OLT SIZE TORQUE IN NM /3 (34) 8-3 (M4) 3. /8 (54) /4-8 (M6).4 3 /4 (70) /4-8 (M6) /8 (86) 5 /6-4 (M8).5 4 / (4) 5 /6-4 (M8) /8 (7) 5 /6-4 (M8).5 6 (5) 5 /6-4 (M8) /4 (7) 5 /6-4 (M8).5 8 (03) 5 /6-4 (M8).5 0 (54) 5 /6-4 (M8).5 (305) 5/6-4 (M8).5 3 /4 (337) 3 /8-4 (M8) (356) 3 /8-4 (M8) / (368) 3/8-4 (M8) / (49) 3 /8-4 (M8) 39.0 * Specifications for Nor-al supplied fasteners only ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 46

32 s & Fittings F Mini s and Hardware SETION.4 F mini flanges are manufactured to the same high standard as our other F flanges for 4, 3 8,, and 3 4 inch (6.35, 9.53,.7 and 9.05mm) tube sizes. Nor-al Products offers special purpose, double-sided and zero-length reducer mini flanges along with fittings, viewports and feedthroughs in this size, so we can supply all the components necessary to build a complete table-top, small laboratory or gas handling system from stock. F Mini s TYPE DIGRM OLT HOLES Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes K=Weld neck with weld prep K=Weld neck without weld prep dd -M4= Metric Thread DIMETER OR THRED N lank NK lank weld neck with weld prep G N ored D.55 (6.48) N ored D.0380 (9.65) N ored D (.83) N ounterbored for tube E 0.65 (5.88) NK ored weld neck with weld prep G 0.65 (5.88) NK ored weld neck without weld prep F 0.65 (5.88) NT lank NKT lank weld neck with weld prep G NT ored D.55 (6.48) NT ored D.0380 (9.65) NT ored D (.83) NT ounterbored for tube E 0.65 (5.88) NKT ored weld neck with weld prep G 0.65 (5.88) NKT ored weld neck without weld prep F 0.65 (5.88) R lank RK lank weld neck with weld prep H R ored.55 (6.48) R ored.0380 (9.65) R ored (.83) R ored 0.65 (5.88) RK ored weld neck with weld prep H 0.65 (5.88) RK ored weld neck without weld prep I 0.65 (5.88) RT lank RKT lank weld neck with weld prep H RT ored.55 (6.48) RT ored.0380 (9.65) RT ored (.83) RT ored 0.65 (5.88) RKT ored weld neck with weld prep H 0.65 (5.88) RKT ored weld neck without weld prep I 0.65 (5.88) (4.45) Diagram.330 (33.78).06 (6.98) Diagram.330 (33.78).06 (6.98) Diagram.330 (33.78).06 (6.98) Diagram D.330 (33.78).06 (6.98) Diagram E.330 (33.78).06 (6.98).755 (9.8).300 (7.6).300 (7.6).300 (7.6).300 (7.6).300 (7.6) Diagram I.330 (33.78).06 (6.98) Diagram H.330 (33.78).06 (6.98) Diagram G.330 (33.78).06 (6.98) Diagram F.330 (33.78).06 (6.98).500 (.70).060 (.5).500 (.70).060 (.5).500 (.70).500 (.70) F Mini Hardware.750 (9.05) DESRIPTION.67 (7.07).750 (9.05) G-33 (0) OFH copper gaskets G-33-SP (0) Silver plated copper gaskets G-33V (5) FKM gaskets -33 (5) SS 8-3 x.75 inch bolts, nuts & washers -33T (5) SS 8-3 x.56 inch bolts & washers -33-SP (5) Silver plated SS 8-3 x.75 inch bolts, nuts & washers -33T-SP (5) Silver plated SS 8-3 x.56 inch bolts & washers NP-075 (4) 8-3 plate nuts. See page 63. KNP-075 () Plate nuts and (4) 8-3 x.75 inch bolts.67 (7.07).750 (9.05) SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Materials s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque: 3. Nm Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: >x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º.750 (9.05) 47

33 SETION.4 s & Fittings F s and Hardware SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Materials s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM olts: 8-8 stainless steel Torque:.4 Nm Diagram. (53.85).65 (4.8) Diagram. (53.85).65 (4.8) Diagram. (53.85).65 (4.8) Diagram D. (53.85).65 (4.8) Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º (.9) (.9) (.9) (.9) F s - /8 Inch (54mm) Nominal TYPE DIGRM ID Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M6 = Metric tapped bolt holes OLT HOLES DIMETER OR THRED -000N lank N ored 0.55 (6.48) N ored (.83) N ored (7.48) (9.30) 0.67 (4.4) N ored (3.83).00 (5.65) 0.67 (4.4) NT lank NT ored 0.55 (6.48) NT ored (.83) NT ored (7.48) (9.30) 0.67 (4.4) NT ored (3.83).00 (5.65) 0.67 (4.4) R lank R ored D 0.55 (6.48) R ored D (.83) R ored D (7.48) (9.30) 0.67 (4.4) R ored D (3.83).00 (5.65) 0.67 (4.4) RT lank RT ored D 0.55 (6.48) RT ored D (.83) RT ored D (7.48) (9.30) 0.67 (4.4) RT ored D (3.83).00 (5.65) 0.67 (4.4) F Hardware - /8 (54mm) Inch Nominal DESRIPTION G- (0) OFH copper gaskets G-V (5) FKM gaskets - (5) SS 4-8 x 4 inch bolts, nuts & washers -T (5) SS 4-8 x 7 /8 inch bolts & washers -- (5) SS -pt. 4-8 x 4 inch bolts, nuts & washers -T- (5) SS -pt. 4-8 x 7 /8 inch bolts & washers ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 48

34 s & Fittings F s and Hardware SETION.4 F s - 3 /4 Inch (70mm) Nominal TYPE DIGRM ID OLT HOLES DIMETER OR THRED N lank N ored 0.55 (6.48) N ored (.83) N ored (7.48) (9.30) 0.09 (5.3) N ored (3.83).00 (5.65) 0.09 (5.3) N ored.88 (30.8).60 (3.00) 0.09 (5.3) N ored.438 (36.53).50 (38.35) 0.09 (5.3) N ored.560 (39.6).635 (4.53) 0.09 (5.3) N ored.60 (4.5).760 (44.70) 0.09 (5.3) NT lank NT ored 0.55 (6.48) NT ored (.83) NT ored (7.48) (9.30) 0.09 (5.3) NT ored (3.83).00 (5.65) 0.09 (5.3) NT ored.88 (30.8).60 (3.00) 0.09 (5.3) NT ored.438 (36.53).50 (38.35) 0.09 (5.3) NT ored.560 (39.6).635 (4.53) 0.09 (5.3) NT ored.60 (4.5).760 (44.70) 0.09 (5.3) R lank R ored D 0.55 (6.48) R ored D (.83) R ored D (30.8) (9.30) 0.09 (5.3) R ored D (3.83).00 (5.65) 0.09 (5.3) R ored D.88 (30.8).60 (3.00) 0.09 (5.3) R ored D.438 (36.53).50 (38.35) 0.09 (5.3) RT lank RT ored D 0.55 (6.48) RT ored D (.83) RT ored D (30.8) (9.30) 0.09 (5.3) RT ored D (3.83).00 (5.65) 0.09 (5.3) RT ored D.88 (30.8).60 (3.00) 0.09 (5.3) RT ored D.438 (36.53).50 (38.35) 0.09 (5.3) Diagram.73 (69.34).3 (58.73) Diagram.73 (69.34).3 (58.73) Diagram.73 (69.34).3 (58.73) Diagram D.73 (69.34).3 (58.73) (.70) (.70) (.70) (.70) Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M6 = Metric tapped bolt holes F Hardware - 3 /4 (70mm) Inch Nominal DESRIPTION G-75 (0) OFH copper gaskets G-75V (5) FKM gaskets G-75-SP (0) Silver plated copper gaskets -75 (5) SS /4-8 x /4 inch bolts, nuts & washers -75T (5) SS /4-8 x inch bolts & washers -75- (5) SS -pt. /4-8 x /4 inch bolts, nuts & washers -75--SP (5) Silver plated SS -pt. /4-8 x /4 inch bolts, nuts & washers -75T- (5) SS -pt. /4-8 x inch bolts & washers -75T--SP (5) Silver plated SS -pt. /4-8 x 7 /8 inch bolts & washers -75T-M (5) SS (metric) M6 x.00 x 5mm bolts & washers NP-50 (4) 4-8 plate nuts. See page 66 KNP-50 () Plate nuts, (4) /4-8 x /4 inch bolts & washers KNP-50- () Plate nuts, (4) -pt. /4-8 x /4 inch bolts & washers SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance holes Materials s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque:.4 Nm Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 49

35 SETION.4 s & Fittings F s and Hardware D D Diagram E Diagram E Diagram E Diagram D E F F F F F s /8 Inch (86mm) Nominal TYPE DIGRM ID D E F OLT HOLES DIMETER OR THRED N lank 3.36 (85.34) (7.39) (7.45) N ored 3.36 (85.34).438 (36.53).50 (38.35) 0.5 (5.7).850 (7.39) (7.45) N ored 3.36 (85.34).938 (49.3).00 (5.05) 0.5 (5.7).850 (7.39) (7.45) NT lank 3.36 (85.34) (7.39) (7.45) NT ored 3.36 (85.34).438 (36.53).50 (38.35) 0.5 (5.7).850 (7.39) (7.45) NT ored 3.36 (85.34).938 (49.3).00 (5.05) 0.5 (5.7).850 (7.39) (7.45) R lank 3.36 (85.34) (7.39) (7.45) R ored D 3.36 (85.34).438 (36.53).50 (38.35) 0.5 (5.7).850 (7.39) (7.45) R ored D 3.36 (85.34).938 (49.3).00 (5.05) 0.5 (5.7).850 (7.39) (7.45) RT lank 3.36 (85.34) (7.39) (7.45) RT ored D 3.36 (85.34).438 (36.53).50 (38.35) 0.5 (5.7).850 (7.39) (7.45) RT ored D 3.36 (85.34).938 (49.3).00 (5.05) 0.5 (5.7).850 (7.39) (7.45) F s - 4 / Inch (4mm) Nominal TYPE DIGRM ID D E F OLT HOLES DIMETER OR THRED N lank 4.47 (3.54) (9.5) (7.45) N ored 4.47 (3.54).438 (36.53).50 (38.35) (9.53) 3.68 (9.5) (7.45) N ored 4.47 (3.54).938 (49.3).00 (5.05) (9.53) 3.68 (9.5) (7.45) N ored 4.47 (3.54).438 (6.93).50 (63.75) (9.53) 3.68 (9.5) (7.45) NT lank 4.47 (3.54) (9.5) (7.45) NT ored 4.47 (3.54).438 (36.53).50 (38.35) (9.53) 3.68 (9.5) (7.45) NT ored 4.47 (3.54).938 (49.3).00 (5.05) (9.53) 3.68 (9.5) (7.45) NT ored 4.47 (3.54).438 (6.93).50 (63.75) (9.53) 3.68 (9.5) (7.45) R lank 4.47 (3.54) (9.5) (9.05) R ored D 4.47 (3.54).438 (36.53).50 (38.35) (9.53) 3.68 (9.5) (9.05) R ored D 4.47 (3.54).938 (49.3).00 (5.05) (9.53) 3.68 (9.5) (9.05) R ored D 4.47 (3.54).438 (6.93).50 (63.75) (9.53) 3.68 (9.5) (9.05) RT lank 4.47 (3.54) (9.5) (9.05) RT ored D 4.47 (3.54).438 (36.53).50 (38.35) (9.53) 3.68 (9.5) (9.05) RT ored D 4.47 (3.54).938 (49.3).00 (5.05) (9.53) 3.68 (9.5) (9.05) RT ored D 4.47 (3.54).438 (6.93).50 (63.75) (9.53) 3.68 (9.5) (9.05) SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Materials s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque:.5 Nm Vacuum range Metal seal: > x 0-3 mbar- UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M8 = Metric tapped bolt holes F Hardware /8 Inch (86mm) Nominal DESRIPTION G-338 (0) OFH copper gaskets G-338-SP (0) Silver plated copper gaskets G-338V () FKM gasket -338 (5) SS x 3 /4 inch bolts, nuts & washers -338T (5) SS x /4 inch bolts & washers (5) SS -pt x 3 /4 inch bolts, nuts & washers -338T- (5) SS -pt x /4 inch bolts & washers SP (5) Silver plated SS -pt. 5 /6-4 x 3 /4 inch bolts, nuts & washers -338T--SP (5) Silver plated SS -pt. 5 /6-4 x /4 inch bolts, washers NP-00 (4) plate nuts. See page 66 KNP-00 (6) Plate nuts, (3) x 3 /4 inch bolts & washers KNP-00- (6) Plate nuts, (3) -pt x 3 /4 inch bolts & washers F Hardware - 4 / Inch (4mm) Nominal DESRIPTION G-450 (0) OFH copper gaskets G-450-SP (0) Silver plated copper gaskets G-450V () FKM gasket -450 (5) SS x inch bolts, nuts & washers -450T (5) SS x /4 inch bolts & washers (5) SS -pt x inch bolts, nuts & washers -450T- (5) SS -pt x /4 inch bolts & washers SP (5) Silver plated SS -pt. 5 /6-4 x inch bolts, nuts & washers -450T--SP (5) Silver plated SS -pt. 5 /6-4 x /4 inch bolts & washers -450-M (5) SS (metric) M8 x.5 x 35mm bolts & washers NP-50 (4) plate nuts. See page 66 KNP-50 (6) Plate nuts, (3) x inch bolts & washers KNP-50- (6) Plate nuts, (3) -pt x inch bolts & washers 50

36 s & Fittings F s and Hardware SETION.4 F s /8 Inch (7mm) Nominal TYPE DIGRM ID D E F OLT HOLES DIMETER OR THRED N lank 4.6 (7.09) (0.6) (0.36) N ored 4.6 (7.09).938 (74.63) 3.00 (76.45) 0.8 (0.6) 0.8 (7.4) (0.36) NT lank 4.6 (7.09) (0.6) (0.36) NT ored 4.6 (7.09).938 (74.63) 3.00 (76.45) 0.8 (0.6) 0.8 (7.4) (0.36) R lank 4.6 (7.09) (0.6) (0.36) R ored D 4.6 (7.09).938 (74.63) 3.00 (76.45) 0.8 (0.6) 0.8 (7.4) (0.36) RT lank 4.6 (7.09) (0.6) (0.36) RT ored D 4.6 (7.09).938 (74.63) 3.00 (76.45) 0.8 (0.6) 0.8 (7.4) (0.36) Diagram F Diagram F D F s - 6 Inch (5mm) Nominal TYPE DIGRM ID D E F OLT HOLES DIMETER OR THRED N lank 5.97 (5.64) (9.84) (30.5) N ored 5.97 (5.64) 3.90 (99.3) 4.00 (0.85) 0.78 (9.84) (.3) 5.8 (30.5) NT lank 5.97 (5.64) (9.84) (30.5) NT ored 5.97 (5.64) 3.90 (99.3) 4.00 (0.85) 0.78 (9.84) (.3) 5.8 (30.5) R lank 5.97 (5.64) (.44) (30.5) R ored D 5.97 (5.64) 3.90 (99.3) 4.00 (0.85) (.44) (.3) 5.8 (30.5) RT lank 5.97 (5.64) (.44) (30.5) RT ored D 5.97 (5.64) 3.90 (99.3) 4.00 (0.85) (.44) (.3) 5.8 (30.5) E Diagram F D D Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M8 = Metric tapped bolt holes E Diagram D F D F Hardware /8 Inch (7mm) Nominal DESRIPTION G-46 (0) OFH copper gaskets G-46V () FKM gasket -46 (5) SS x /4 inch bolts, nuts & washers -46T (5) SS x /4 inch bolts & washers -46- (5) SS -pt x /4 inch bolts, nuts & washers -46T- (5) SS -pt x /4 inch bolts & washers NP-300 (4) plate nuts. See page 66 KNP-300 (0) Plate nuts, (40) x /4 inch bolts & washers KNP-300- (0) Plate nuts, (40) -pt x /4 inch bolts & washers F Hardware - 6 Inch (5mm) Nominal DESRIPTION G-600 (0) OFH copper gaskets G-600V () FKM gasket G-600-SP (0) Silver plated copper gaskets -600 (5) SS x /4 inch bolts, nuts & washers -600T (5) SS x /4 inchbolts & washers (5) SS -pt x /4 inch bolts, nuts & washers -600T- (5) SS -pt x /4 inch bolts & washers SP (5) Silver plated SS -pt x /4 inch bolts, nuts & washers -600T--SP (5) Silver plated SS -pt x /4 inch bolts & washers -600T-M (5) SS (metric) M8 x /4 x 35mm bolts & washers NP-400 (4) plate nuts. See page 66 KNP-400 (6) Plate nuts (3) x /4 inch bolts & washers KNP-400- (6) Plate nuts (3) -pt x /4 inch bolts & washers SPEIFITIONS General:Rotatable and nonrotatable with tapped or clearance bolt holes Materials s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM and silver plated olts: 8-8 stainless steel and silver plated Torque:.5 Nm Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º 5

37 SETION.4 s & Fittings F s and Hardware E Diagram F Diagram F D D F s /4 Inch (7mm) Nominal TYPE DIGRM ID D E F OLT HOLES DIMETER OR THRED N lank 6.73 (70.94) (.44) (5.6) N ored 6.73 (70.94) (3.83) 5.00 (7.5) (.44) (.68) (5.6) NT lank 6.73 (70.94) (.44) (5.6) ) NT ored 6.73 (70.94) (3.83) 5.00 (7.5) (.44) (.68) (5.6) R lank 6.73 (70.94) (.44) (5.6) R ored D 6.73 (70.94) (3.83) 5.00 (7.5) (.44) (.68) (5.6) RT lank 6.73 (70.94) (.44) (5.6) RT ored D 6.73 (70.94) (3.83) 5.00 (7.5) (.44) (.68) (5.6) Diagram F Diagram D F D F s - 8 Inch (03mm) Nominal TYPE DIGRM ID D E F OLT HOLES OR DIMETER THRED N lank 7.97 (0.44) (.3) (8.05) N ored 7.97 (0.44) (49.3) 6.00 (5.9) (.3) (.7) 7.8 (8.05) NT lank 7.97 (0.44) (.3) (8.05) NT ored 7.97 (0.44) (49.3) 6.00 (5.9) (.3) (.7) 7.8 (8.05) R lank 7.97 (0.44) (.3) (8.05) R ored D 7.97 (0.44) (49.3) 6.00 (5.9) (.3) (.7) 7.8 (8.05) RT lank 7.97 (0.44) (.3) (8.05) RT ored D 7.97 (0.44) (49.3) 6.00 (5.9) (.3) (.7) 7.8 (8.05) E D Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M8 = Metric tapped bolt holes SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque:.5 Nm Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. F Hardware /4 Inch (7mm) Nominal DESRIPTION G-675 (0) OFH copper gaskets G-675V () FKM gasket -675 (5) SS x /4 inch bolts, nuts & washers -675T (5) SS x / inch bolts & washers (5) SS -pt x /4 inch bolts, nuts & washers -675T- (5) SS -pt x 3 /4 inch bolts & washers F Hardware - 8 Inch (03mm) Nominal DESRIPTION G-800 (0) OFH copper gaskets G-800V () FKM gasket G-800-SP (0) Silver plated copper gaskets -800 (5) SS x /4 inch bolts, nuts & washers -800T (5) SS x 3 /4 inch bolts & washers (5) SS -pt x /4 inch bolts, nuts & washers -800T- (5) SS -pt x 3 /4 inch bolts & washers SP (5) Silver plated SS -pt. 5 /6-4 x /4 inch bolts, nuts & washers -800T--SP (5) Silver plated SS -pt. 5 /6-4 x 3 /4 inch bolts & washers -800T-M (5) SS (metric) M8 x /4 x 45mm bolts & washers NP-600 (4) plate nuts. See page 66 KNP-600 (0) Plate nuts, (40) x /4 inch bolts & washers KNP-600- (0) Plate nuts, (40) x /4 inch -pt. bolts & washers 5

38 SETION.4 s & Fittings F s and Hardware F s - 0 Inch (54mm) Nominal Diagram TYPE DIGRM ID D E F OLT HOLES OR DIMETER THRED N lank 9.97 (53.4) (4.59) (3.85) N ored 9.97 (53.4) (00.03) 8.00 (03.7) (4.59) (.70) 9.8 (3.85) NT lank 9.97 (53.4) (4.59) (3.85) NT ored 9.97 (53.4) (00.03) 8.00 (03.7) (4.59) (.70) 9.8 (3.85) R lank 9.97 (53.4) (4.59) (3.85) R ored D 9.97 (53.4) (00.03) 8.00 (03.7) (4.59) (.70) 9.8 (3.85) RT lank 9.97 (53.4) (4.59) (3.85) RT ored D 9.97 (53.4) (00.03) 8.00 (03.7) (4.59) (.70) 9.8 (3.85) E F Diagram F D D F s - Inch (305mm) Nominal TYPE DIGRM ID D E F OLT HOLES OR DIMETER THRED N lank.00 (304.80) (8.58) -.8 (84) N ored.00 (304.80) (50.83) 0.00 (54.5).5 (8.58) (.70).8 (84) NT lank.00 (304.80) (8.58) -.8 (84) NT ored.00 (304.80) (50.83) 0.00 (54.5).5 (8.58) (.70).8 (84) R lank.00 (304.80) (8.58) -.8 (84) R ored D.00 (304.80) (50.83) 0.00 (54.5).5 (8.58) (.70).8 (84) RT lank.00 (304.80) (8.58) -.8 (84) RT ored D.00 (304.80) (50.83) 0.00 (54.5).5 (8.58) (.70).8 (84) Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M8 = Metric tapped bolt holes E Diagram F Diagram D F D D F Hardware - 0 Inch (54mm) Nominal DESRIPTION G-000 (0) OFH copper gaskets G-000V () FKM gasket G-000-SP (0) Silver plated copper gaskets -000 (5) SS x / inch bolts, nuts & washers -000T (5) SS x 3 /4 inch bolts & washers (5) SS -pt x / inch bolts, nuts & washers -000T- (5) SS -pt x 3 /4 inch bolts & washers SP (5) Silver plated SS -pt. 5 /6-4 x / inch bolts, nuts & washers -000T--SP (5) Silver plated SS -pt. 5 /6-4 x 3 /4 inch bolts & washers -000T-M (5) SS (metric) M8 x /4 x 45mm bolts & washers NP-800 (4) plate nuts. See page 66 KNP-800 (4) Plate nuts, (48) x /4 inch bolts & washers KNP-800- (4) Plate nuts, (48) -pt x /4 inch bolts & washers SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque:.5 Nm Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º F Hardware - Inch (305mm) Nominal DESRIPTION G-00 () OFH copper gasket -00 (3) SS x 3 inch bolts, nuts & washers -00T (3) SS x 3 /4 inch bolts & washers 53

39 SETION.4 s & Fittings F s and Hardware D Diagram E Diagram E.5 (8.58).5 (8.58) F s - 3 /4 Inch (337mm) Nominal TYPE DIGRM ID D E OLT HOLES DIMETER OR THRED N lank 3.5 (336.55) (306.0) N ored 3.5 (336.55) (50.83) 0.00 (54.5) (.70).055 (306.0) NT lank 3.5 (336.55) (306.0) NT ored 3.5 (336.55) (50.83) 0.00 (54.5) (.70).055 (306.0) R lank 3.5 (336.55) (306.0) R ored D 3.5 (336.55) (50.83) 0.00 (54.5) (.70).055 (306.0) RT lank 3.5 (336.55) (306.0) RT ored D 3.5 (336.55) (50.83) 0.00 (54.5) (.70).055 (306.0) Diagram E Diagram D E.5 (8.58) F s - 4 Inch (356mm) Nominal TYPE DIGRM ID D E OLT HOLES DIMETER OR THRED N lank 4.00 (355.60) (35.37) N ored 4.00 (355.60).875 (30.63).030 (305.56) (.70).80 (35.37) NT lank 4.00 (355.60) (35.37) NT ored 4.00 (355.60).875 (30.63).030 (305.56) (.70).80 (35.37) R lank 4.00 (355.60) (35.37) R ored D 4.00 (355.60).875 (30.63).030 (305.56) (.70).80 (35.37) RT lank 4.00 (355.60) (35.37) RT ored D 4.00 (355.60).875 (30.63).030 (305.56) (.70).80 (35.37) Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M8 = Metric tapped bolt holes D.5 (8.58) SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM olts: 8-8 stainless steel Torque: 39.0 Nm Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º F Hardware -3 /4 Inch (337mm) Nominal DESRIPTION G-35 () OFH copper gasket G-35V () FKM gasket -35 (30) SS x 3 inch bolts, nuts & washers -35T (30) SS x inch bolts & washers F Hardware - 4 Inch (356mm) Nominal DESRIPTION G-400 () OFH copper gasket G-400V () FKM gasket -400 (30) SS x 3 inch bolts, nuts & washers -400T (30) SS x inch bolts & washers ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 54

40 SETION.4 s & Fittings F s and Hardware F s - 4 / Inch (368mm) Nominal TYPE DIGRM ID D E OLT HOLES DIMETER OR THRED N lank 4.50 (368.30) lank (338.07) N ored 4.50 (368.30).875 (30.63).00 (305.3) (.70) 3.30 (338.07) NT lank 4.50 (368.30) lank (338.07) NT ored 4.50 (368.30).875 (30.63).00 (305.3) (.70) 3.30 (338.07) R lank 4.50 (368.30) lank (338.07) R ored D 4.50 (368.30).875 (30.63).00 (305.3) (.70) 3.30 (338.07) RT lank 4.50 (368.30) lank (338.07) RT ored D 4.50 (368.30).875 (30.63).00 (305.3) (.70) 3.30 (338.07) D Diagram E Diagram E.5 (8.58).5 (8.58) F s - 6 / Inch (49mm) Nominal TYPE DIGRM ID D E OLT HOLES DIMETER OR THRED N lank 6.50 (49.0) lank (388.87) N ored 6.50 (49.0) (349.5) 4.00 (356.) (.70) 5.30 (388.87) NT lank 6.50 (49.0) lank (388.87) NT ored 6.50 (49.0) (349.5) 4.00 (356.) (.70) 5.30 (388.87) R lank 6.50 (49.0) lank (388.87) R ored D 6.50 (49.0) (349.5) 4.00 (356.) (.70) 5.30 (388.87) RT lank 6.50 (49.0) lank (388.87) RT ored D 6.50 (49.0) (349.5) 4.00 (356.) (.70) 5.30 (388.87) Model Number Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes R = Rotatable, clearance bolt holes RT = Rotatable, tapped bolt holes dd -M8 = Metric tapped bolt holes Diagram E Diagram D E.5 (8.58) D.5 (8.58) F Hardware - 4 / Inch (368mm) Nominal DESRIPTION G-450 () OFH copper gasket -450 (3) SS x 3 inch bolts, nuts & washers -450T (3) SS x inch bolts & washers F Hardware - 6 / Inch (49mm) Nominal DESRIPTION G-650 () OFH copper gasket G-650V () FKM gasket -650 (36) SS x 3 inch bolts, nuts & washers -650T (36) SS x inch bolts & washers SPEIFITIONS General: Rotatable and nonrotatable with tapped or clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM olts: 8-8 stainless steel Torque: 39 Nm. Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 55

41 SETION.4 s & Fittings F Special Purpose s SPEIFITIONS General:Nonrotatable with clearance bolt holes Material s:304 stainless steel (36L available on request) Gaskets: opper, FKM olts: 8-8 stainless steel Torque: See page 46 Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Diagram Diagram Diagram Diagram D 0 0 Nor-al s special purpose F flanges are used as roughing accessories, accommodating thermocouple gauge tubes, up-to-air valves and/or NPT threaded fittings. Double-sided flanges are provided with one or more radially tapped holes. lank flanges are provided with a single concentric /8 NPT tapped hole. Hardware for special purpose flanges is located on the appropriate flange size pages. F Double-Sided Special Purpose s FLNGE FETURE DIGRM 33-D.33 (33.78) () 6 inch (.59) NPT hole 0.5 (6.35) 0.50 (.70) 75-D.75 (69.85) () 8 inch (3.8) NPT hole 0.38 (9.65) 0.75 (9.05) 33-D.33 (33.78) () 6 inch (.59) NPT holes 0.5 (6.35) 0.50 (.70) 75-D.75 (69.85) () 8 inch (3.8) NPT holes 0.38 (9.65) 0.75 (9.05) 33-DT.33 (33.78) Thermocouple gauge tube 0.5 (6.35) 0.50 (.70) 75-DT.75 (69.85) Thermocouple gauge tube 0.38 (9.65) 0.75 (9.05) 33-DV.33 (33.78) Up-to-air valve D 0.5 (6.35) 0.50 (.70) 75-DV.75 (69.85) Up-to-air valve D 0.38 (9.65) 0.75 (9.05) 33-DV- 4 MVR.33 (33.78) Up-to-air valve & 4 inch (6.35) ajon male VR fitting on valve D 0.5 (6.35) 0.50 (.70) 75-DV- 4 MVR.75 (69.85) Up-to-air valve & 4 inch (6.35) ajon male VR fitting on valve D 0.38 (9.65) 0.75 (9.05) 33-DV- 4 FVR.33 (33.78) Up-to-air valve & 4 inch (6.35) ajon female VR fitting on valve D 0.5 (6.35) 0.50 (.70) 75-DV- 4 FVR.75 (69.85) Up-to-air valve & 4 inch (6.35) ajon female VR fitting on valve D 0.38 (9.65) 0.75 (9.05) 33-DV- 4 SWG.33 (33.78) Up-to-air valve & 4 inch (6.35) Swagelok fitting on valve D 0.5 (6.35) 0.50 (.70) 75-DV- 4 SWG.75 (69.85) Up-to-air valve & 4 inch (6.35) Swagelok fitting on valve D 0.38 (9.65) 0.75 (9.05) 33-DV.33 (33.78) () 6 inch (.59) NPT hole & up-to-air valve F 0.5 (6.35) 0.50 (.70) 75-DV.75 (69.85) () 8 inch (3.8) NPT hole & up-to-air valve F 0.38 (9.65) 0.75 (9.05) 33-DTV.33 (33.78) Thermocouple gauge tube & up-to-air valve E 0.5 (6.35) 0.50 (.70) 75-DTV.75 (69.85) Thermocouple gauge tube & up-to-air valve E 0.38 (9.65) 0.75 (9.05) 33-DTV- 4 MVR.33 (33.78) 75-DTV- 4 MVR.75 (69.85) 33-DTV- 4 FVR.33 (33.78) 75-DTV- 4 FVR.75 (69.85) 33-DTV- 4 SWG.33 (33.78) 75-DTV- 4SWG.75 (69.85) Thermocouple gauge tube & up-to-air valve with 4 inch (6.35) ajon male VR fitting on valve Thermocouple gauge tube & up-to-air valve with 4 inch (6.35) ajon male VR fitting on valve Thermocouple gauge tube & up-to-air valve with 4 inch (6.35) ajon female VR fitting on valve Thermocouple gauge tube & up-to-air valve with 4 inch (6.35) ajon female VR fitting on valve Thermocouple gauge tube & up-to-air valve with 4 inch (6.35) Swagelok fitting on valve Thermocouple gauge tube & up-to-air valve with 4 inch (6.35) Swagelok fitting on valve E 0.5 (6.35) 0.50 (.70) E 0.38 (9.65) 0.75 (9.05) E 0.5 (6.35) 0.50 (.70) E 0.38 (9.65) 0.75 (9.05) E 0.5 (6.35) 0.50 (.70) E 0.38 (9.65) 0.75 (9.05) 75-DS-MINI.75 (69.85) ().33 inch (33.78) side port G 0.38 (9.65) 0.75 (9.05) Diagram E Optional fitting WELD Diagram F Optional fitting Optional fitting WELD Diagram G WELD WELD.33 F 56

42 SETION.4 s & Fittings F Special Purpose s F Straight-Through Special Purpose s FLNGE FETURE DIGRM 33-ST.33 (33.78) () 8 inch (3.8) NPT hole 75-ST.75 (69.85) () 8 inch (3.8) NPT hole 33-STT.33 (33.78) Thermocouple gauge tube 75-STT.75 (69.85) Thermocouple gauge tube 33-STV.33 (33.78) Up-to-air valve 75-STV.75 (69.85) Up-to-air valve 33-STV- 4 MVR.33 (33.78) Up-to-air valve and 4 inch (6.35) ajon male VR fitting on valve 75-STV- 4 MVR.75 (69.85) Up-to-air valve and 4 inch (6.35) ajon male VR fitting on valve 33-STV- 4 FVR.33 (33.78) Up-to-air valve and 4 inch (6.35) ajon female VR fitting on valve 75-STV- 4 FVR.75 (69.85) Up-to-air valve and 4 inch (6.35) ajon female VR fitting on valve 33-STV- 4 SWG.33 (33.78) Up-to-air valve and 4 inch (6.35) Swagelok fitting on valve 75-STV- 4 SWG.75 (69.85) Up-to-air valve and 4 inch (6.35) Swagelok fitting on valve SPEIFITIONS General:Nonrotatable with clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM olts: 8-8 stainless steel Torque: See page 46 Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Diagram Diagram Diagram /8 (3.8) NPT /8 (3.8) NPT WELD Optional fitting ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 57

43 SETION.4 s & Fittings F Double-Sided s Nor-al Products double-sided flanges are identical to standard F flanges except the same gasket-sealing detail is machined into both faces of the flange. These flanges can be inserted between like-sized flanges as spacers, orifice plates, or when radially drilled, as custom penetrations into vacuum systems. F Double-Sided s NOMINL MDE FROM D 3 (34) N (7.6) 33-05D 3 (34) N 0.55 (6.48) (7.6) D 3 (34) N (9.65) (7.6) D 3 (34) N (.83) (7.6) D 3 (34) N (6.00) (7.6) DS 3 (34) NS (.7) DS 3 (34) NS (6.00) (.7) -000D 8 (54) -000N (.94) -00D 8 (54) -000N.00 (5.65) (.94) D 8 (54) N (.7) 75-05D 3 4 (70) N 0.55 (6.48) (.7) D 3 4 (70) N (.83) (.7) D 3 4 (70) N (9.30) (.7) 75-00D 3 4 (70) N.00 (5.65) (.7) 75-5D 3 4 (70) N.60 (3.00) (.7) 75-50D 3 4 (70) N.50 (38.35) (.7) DS 3 4 (70) NS (9.05) 75-50DS 3 4 (70) NS.50 (38.35) (9.05) D (86) N (7.45) D (86) N.50 (38.35) (7.45) D (86) N.00 (5.05) (7.45) D 4 (4) N (7.45) D 4 (4) N.50 (38.35) (7.45) D 4 (4) N.00 (5.05) (7.45) D 4 (4) N.50 (63.75) (7.45) D (7) N (0.6) D (7) N 3.00 (76.45) 0.8 (0.6) D 6 (5) N (9.84) D 6 (5) N 4.00 (0.85) 0.78 (9.84) D (7) N (.44) D (7) N 5.00 (7.5) (.44) D 8 (03) N (.3) D 8 (03) N 6.00 (5.9) (.3) D 0 (54) N (4.59) D 0 (54) N 8.00 (03.7) (4.59) D 3 4 (337) N -.5 (8.58) D 3 4 (337) N 0.00 (54.5).5 (8.58) D 4 (356) N -.5 (8.58) D 4 (356) N.00 (305.3).5 (8.58) DS = Thicker than standard flange D = Double-sided flange, nonrotatable F Double-Sided Hardware NOMINL DESRIPTION G-33 3 (34) (0) OFH copper gaskets G-33V 3 (34) (5) FKM gaskets -33D 3 (34) (5) SS 8-3 x /4 inch bolts, nuts and washers G- 8 (54)) (0) OFH copper gaskets G-V 8 (54) (5) FKM gaskets -D 8 (54) (5) SS 4-8 x 3 /4 inch bolts, nuts and washers G (70) (0) OFH copper gaskets G-75V 3 4 (70) (5) FKM gaskets -75DS 3 4 (70) (5) SS 4-8 x inch bolts, nuts and washers -75D 3 4 (70) (5) SS 4-8 x 3 /4 inch bolts, nuts and washers KNP-50D 3 4 (70) (6) Plate nuts, 4-8 x inch () bolts and washers G (86) (0) OFH copper gaskets G-338V (86) () FKM gaskets -338D (86) (5) SS x / inch bolts, nuts and washers G (4) (0) OFH copper gaskets G-450V 4 (4) () FKM gaskets -450D 4 (4) (5) SS x 3 3 /4 inch bolts, nuts and washers G (7) (0) OFH copper gaskets G-46V (7) () FKM gaskets -46D (7) (5) SS x 3 inch bolts, nuts and washers G (5) (0) OFH copper gaskets G-600V 6 (5) () FKM gaskets -600D 6 (5) (5) SS x 3 inch bolts, nuts and washers G (7) (0) OFH copper gaskets G-675V (7) () FKM gaskets -675D (7) (5) SS x 3 inch bolts, nuts and washers G (03) (0) OFH copper gaskets G-800V 8 (03) () FKM gaskets -800D 8 (03) (5) SS x 3 inch bolts, nuts & washers G (54) (0) OFH copper gaskets G-000V 0 (54) () FKM gaskets -000D 0 (54) (5) SS x 3 / inch bolts, nuts and washers G (337) () OFH copper gaskets G-35V 3 4 (337) () FKM gaskets SPEIFITIONS General: Nonrotatable with clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM olts: 8-8 stainless steel Torque: See page 46 Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º 58

44 SETION.4 s & Fittings F Zero Length Reducer s Nor-al Products zero length reducer flanges are a convenient and inexpensive way to reduce a large flange for smaller vacuum plumbing and/or component connection. To list all possible reducer combinations would require excessive space, therefore only the most commonly used reducers are listed. If your requirement is not listed, please inquire. F Zero Length Reducer s SMLL FLNGE DETIL LRGE FLNGE DETIL Z NT -000NT 0.65 (5.88) (.94) Z NT N 0.65 (5.88) (.70) Z -000NT NT.000 (5.40) (.70) Z NT N 0.65 (5.88) (7.45) Z -000NT NT.000 (5.40) (7.45) Z NT NT.500 (38.0) (7.45) Z NT N 0.65 (5.88) (7.45) Z -000NT N.000 (5.40) (7.45) Z NT N.500 (38.0) (7.45) Z NT NT.000 (50.80) (7.45) Z NT N 0.65 (5.88) 0.8 (0.6) Z -000NT N.000 (5.40) 0.8 (0.6) Z NT N.500 (38.0) 0.8 (0.6) Z NT N.000 (50.80) 0.8 (0.6) Z NT N 0.65 (5.88) 0.78 (9.84) Z -000NT N.000 (5.40) 0.78 (9.84) Z NT N.500 (38.0) 0.78 (9.84) Z NT N.000 (50.80) 0.78 (9.84) Z NT N.500 (63.50) 0.78 (9.84) Z NT NT (76.0) 0.78 (9.84) Z NT N 0.65 (5.88) (.44) Z -000NT N.000 (5.40) (.44) Z NT N.500 (38.0) (.44) Z NT N.000 (50.80) (.44) Z NT N.500 (63.50) (.44) Z NT N (76.0) (.44) Z NT NT (0.60) (.44) Z NT N 0.65 (5.88) (.3) Z -000NT N.000 (5.40) (.3) Z NT N.500 (38.0) (.3) Z NT N.000 (50.80) (.3) Z NT N.500 (63.50) (.3) Z NT N (76.0) (.3) Z NT N (0.60) (.3) Z NT NT (7.00) (.3) Z NT N 0.65 (5.88) (4.59) Z -000NT N.000 (5.40) (4.59) Z NT N.500 (38.0) (4.59) Z NT N.000 (50.80) (4.59) Z NT N.500 (63.50) (4.59) Z NT N (76.0) (4.59) Z NT N (0.60) (4.59) Z NT N (7.00) (4.59) Z NT N (5.40) (4.59) Z NT N 0.65 (5.88).5 (8.58) Z -000NT N.000 (5.40).5 (8.58) Z 75-00NT N.500 (38.0).5 (8.58) Z NT N.000 (50.80).5 (8.58) Z NT N.500 (63.50).5 (8.58) Z NT N (76.0).5 (8.58) Z NT N (0.60).5 (8.58) Z NT N (7.00).5 (8.58) Z NT N (5.40).5 (8.58) Z NT N (03.0).5 (8.58) SPEIFITIONS General: Nonrotatable with tapped or clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque: See page 46 Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Small Detail Large Detail For gasket and hardware options please refer to appropriate flange page Detail Definitions N = Nonrotatable, clearance bolt holes NT = Nonrotatable, tapped bolt holes ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 59

45 SETION.4 s & Fittings F Fittings SPEIFITIONS General: Rotatable or nonrotatable with clearance bolt holes Materials Tube / s: 304 stainless steel (36L available on request) Gaskets: FKM, copper or silver plated olts: 8-8 stainless steel or silver plated Torque: Refer to specific flange specs Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer: -0º to 50º Nor-al Products manufactures a complete line of vacuum fittings with F flanges. The tube portions are fabricated from 304 stainless steel. On request 36L stainless steel can be supplied. Nor-al Products makes its own elbows, and all tees and crosses are made with the pulled port technique. This allows smooth, crevice-free butt welds to provide the maximum in cleanliness for UHV applications. akeout range is up to 450. Standard finish is bead blasted. Electropolish can also be provided as an option. all for pricing. Nonrotatable F Half Nipples FLNGE TUE N (33.78) 3/4 (9.05).50 (38.0) N-00. (53.85) (5.40).05 (5.07) N (69.85) / (38.0).46 (6.48) N (85.85) (50.80) 3. (8.79) N (4.30) / (63.50) 3.38 (85.85) N-50V 4.50 (4.30) / (63.50) 4. (04.65) N (7.35) 3 (76.0) 3.53 (89.66) N (5.40) 4 (0.60) 4.3 (09.73) N-400V 6.00 (5.40) 4 (0.60) 5.3 (34.87) N (03.0) 6 (5.40) 5.50 (39.70) N-600V 8.00 (03.0) 6 (5.40) 6.56 (66.6) N (54.00) 8 (03.0) 7.50 (90.50) N (336.55) 0 (54.00) 0.00 (54.00) N (355.60) (304.80) 0.00 (54.00) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 60

46 SETION.4 s & Fittings F Fittings F Full Nipples FLNGE TUE N (33.78) 3/4 (9.05) 3.00 (76.0) N-00. (53.85) (5.40) 4.0 (04.4) N (69.85) / (38.0) 4.9 (4.97) N (85.85) (50.80) 6.44 (63.58) N (4.30) / (63.50) 6.76 (7.70) N-50V 4.50 (4.30) / (63.50) 8.4 (09.3) N (7.35) 3 (76.0) 7.06 (79.3) N (5.40) 4 (0.60) 8.64 (9.46) N-400V 6.00 (5.40) 4 (0.60) 0.6 (69.75) N (03.0) 6 (5.40).00 (79.40) N-600V 8.00 (03.0) 6 (5.40) 3. (333.5) N (54.00) 8 (03.0) 5.00 (38.00) N (336.55) 0 (54.00) 0.00 (508.00) N (355.60) (304.80) 0.00 (508.00) Nonrotatable Rotatable Nonrotatable 5.00 (7.00) Rotatable F Reducer Nipples FLNGE FLNGE TUE NR (5.40) 3 /4 (69.85).50 (38.0) NR (03.0) 3 /4 (69.85).50 (38.0) NR (03.0) 4 / (4.30).50 (63.50) NR (03.0) 6 (5.40) 4.00 (0.60) NR (54.00) 3 /4 (69.85).50 (38.0) NR (54.00) 4 / (4.30).50 (63.50) NR (54.00) 6 (5.40) 4.00 (0.60) NR (54.00) 8 (03.0) 6.00 (5.40) NR (336.55) 0 (54.00) 8.00 (03.0) NR (355.60) (304.80) 0.00 (54.00) Note: Reducer nipples with other F flanges and different lengths are available upon request. F onical Reducer Nipples FLNGE FLNGE TUE FLNGE FLNGE TUE NR--33. (53.85) (5.40).33 (33.78) 3 /4 (9.05).04 (5.8) NR (69.85) / (38.0).33 (33.78) 3 /4 (9.05) 3.08 (78.3) NR (69.85) / (38.0). (53.85) (5.40).75 (69.85) NR (85.85) (50.80). (53.85) (5.40).77 (70.36) NR (85.85) (50.80).75 (69.85) / (38.0).8 (7.37) NR (4.3) / (63.50).75 (69.85) / (38.0).96 (75.8) NR (4.3) / (63.50) 3.38 (85.85) (50.80).98 (75.69) NR (7.35) 3 (76.0).75 (69.85) / (38.0) 4. (04.65) NR (7.35) 3 (76.0) 3.38 (85.85) (50.80) 4.3 (04.90) NR (7.35) 3 (76.0) 4.50 (4.30) / (63.50) 4.8 (08.7) NR (5.40) 4 (0.60) 3.38 (85.85) (50.80) 4.9 (08.97) NR (5.40) 4 (0.60) 4.50 (4.30) / (63.50) 4.44 (.78) NR (5.40) 4 (0.60) 4.6 (7.35) 3 (76.0) 4.34 (0.4) Nonrotatable Rotatable ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 6

47 SETION.4 s & Fittings F Fittings F 45 Radius Elbow with Tangents FLNGE TUE KL (33.78) 3 /4 (9.05) 0.94 (3.88) KL-00. (53.85) (5.40).4 (8.96) KL (69.85) / (38.0).74 (44.0) KL (85.85) (50.80).07 (5.58) KL (4.30) / (63.50) 3.37 (85.60) KL (7.35) 3 (76.0) 3.96 (00.58) KL (5.40) 4 (0.60) 5. (3.59) oth s Rotatable F 90º Radius Elbows FLNGE TUE E (33.78) 3 /4 (9.05).50 (38.0).00 (5.40) E-00. (5.85) (5.40).67 (4.4).50 (38.0) E (69.85) / (38.0).46 (6.48).5 (57.5) E (85.85) (50.80) 3. (8.79) 3.00 (76.0) E (4.30) / (63.50) 4. (04.65) 3.75 (95.5) E (7.35) 3 (76.0) 4.78 (.4) 4.50 (4.30) E (5.40) 4 (0.60) 6.44 (63.58) 6.00 (5.40) E (03.0) 6 (5.40) 9.50 (4.30) 9.00 (8.60) E (54.00) 8 (03.0).50 (37.50).00 (304.80) E (336.55) 0 (54.00) 5.50 (393.70) 5.00 (38.00) Typ. oth s Rotatable Typ. oth s Rotatable F 90 Mitered Elbows FLNGE TUE E-075M.33 (33.78) 3 /4 (9.05).50 (38.0) E-00M. (53.85) (5.40).05 (5.07) E-50M.75 (69.85) / (38.0).46 (6.48) E-00M 3.38 (85.85) (50.80) 3. (8.79) E-50M 4.50 (4.30) / (63.50) 3.38 (85.85) E-50MV 4.50 (4.30) / (63.50) 4. (04.65) E-300M 4.6 (7.35) 3 (76.0) 3.53 (89.66) E-400M 6.00 (5.40) 4 (0.60) 4.3 (09.73) E-400MV 6.00 (5.40) 4 (0.60) 5.3 (34.87) E-500M 6.75 (7.45) 5 (7.00) 4.7 (9.63) E-600M 8.00 (03.0) 6 (5.40) 5.50 (39.70) E-600MV 8.00 (03.0) 6 (5.40) 6.56 (66.6) E-800M 0.00 (54.00) 8 (03.0) 7.50 (90.50) E-000M 3.5 (336.55) 0 (54.00) 0.00 (54.00) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 6

48 SETION.4 s & Fittings F Fittings Nonrotatable F Tees FLNGE 3T (33.78) 3 /4 (9.05).50 (38.0) 3T-00. (53.85) (5.40).05 (5.07) 3T (69.85) / (38.0).46 (6.48) 3T (85.85) (50.80) 3. (8.79) 3T (4.30) / (63.50) 3.38 (85.85) 3T-50V 4.50 (4.30) / (63.50) 4. (04.65) 3T (7.35) 3 (76.0) 3.53 (89.66) 3T (5.40) 4 (0.60) 4.3 (09.73) 3T-400V 6.00 (5.40) 4 (0.60) 5.3 (34.87) 3T (7.45) 5 (7.00) 4.7 (9.63) 3T (03.0) 6 (5.40) 5.50 (39.70) 3T-600V 8.00 (03.0) 6 (5.40) 6.56 (66.6) 3T (54.00) 8 (03.0) 7.50 (90.50) 3T (336.55) 0 (54.00) 0.00 (54.00) Note: Reducer tees in other tube sizes are available upon request. TUE Rotatable Typ. F Reducer Tees Nonrotatable FLNGE & FLNGE FLNGE & TUE FLNGE 3 FLNGE FLNGE 3 TUE 3TR (69.85) / (38.0).33 (33.78) 3 /4 (9.05).46 (6.48).87 (47.50) 3TR (69.85) / (38.0). (53.85) (5.40).46 (6.48).9 (58.7) 3TR (85.85) (50.80).33 (33.78) 3 /4 (9.05) 3. (8.79).3 (54.0) 3TR (85.85) (50.80).75 (69.85) / (38.0) 3. (8.79).7 (68.83) 3TR (4.30) / (63.50).75 (69.85) / (38.0) 3.38 (85.85).96 (75.8) 3TR (4.30) / (63.50) 3.38 (85.85) (50.80) 3.38 (85.85) 3.48 (88.39) 3TR (7.35) 3 (76.0) 3.38 (85.85) (50.80) 3.53 (89.66) 3.73 (94.74) 3TR (7.35) 3 (76.0) 4.50 (4.3)0 / (63.50) 3.53 (89.66) 3.63 (9.0) 3TR (5.40) 4 (0.60).75 (69.85) / (38.0) 4.3 (09.73) 3.7 (94.3) 3TR (5.40) 4 (0.60) 3.38 (85.85) (50.80) 4.3 (09.73) 4.3 (07.44) 3TR (5.40) 4 (0.60) 4.50 (4.30) / (63.50) 4.3 (09.73) 4.3 (04.90) 3TR (5.40) 4 (0.60) 4.6 (7.35) 3 (76.0) 4.3 (09.73) 4.03 (0.36) 3TR (7.45) 5 (7.00) 6.00 (5.40) 4 (0.60) 4.7 (9.63) 4.8 (.43) 3TR (03.0) 6 (5.40).75 (69.85) / (38.0) 5.50 (39.70) 4.7 (9.63) 3TR (03.0) 6 (5.40) 3.38 (85.85) (50.80) 5.50 (39.70) 5.3 (3.84) 3TR (03.0) 6 (5.40) 4.50 (4.30) / (63.50) 5.50 (39.70) 5.3 (30.30) 3TR (03.0) 6 (5.60) 6.00 (5.40) 4 (0.60) 5.50 (39.70) 5.3 (35.3) 3TR (54.00) 8 (03.0) 8.00 (03.0) 6 (5.40) 7.50 (90.50) 6.50 (65.0) Rotatable 3 Typ. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 63

49 SETION.4 s & Fittings F Fittings Rotatable 4 3 Nonrotatable Typ. Typ. F Reducer rosses FLNGE & FLNGE FLNGE & TUE FLNGE 3 & 4 FLNGE FLNGE 3 & 4 TUE 4R (69.85) / (38.0).33 (33.78) 3/4 (9.05).46 (6.48).87 (47.50) 4R (69.85) / (38.0). (53.85) (5.40).46 (6.48).9 (58.7) 4R (85.85) (50.80).33 (33.78) 3 /4 (9.05) 3. (8.79).3 (54.0) 4R (85.85) (50.80).75 (69.85) / (38.0) 3. (8.79).7 (68.83) 4R (4.30) / (63.50).75 (69.85) / (38.0) 3.38 (85.85).96 (75.8) 4R (4.30) / (63.50) 3.38 (85.85) (50.80) 3.38 (85.85) 3.48 (88.39) 4R (7.35) 3 (76.0) 3.38 (85.85) (50.80) 3.53 (89.66) 3.73 (94.74) 4R (7.35) 3 (76.0) 4.50 (4.30) / (63.50) 3.53 (89.66) 3.63 (9.) 4R (5.40) 4 (0.60).75 (69.85) / (38.0) 4.3 (09.73) 3.7 (94.3) 4R (5.40) 4 (0.60) 3.38 (85.85) (50.80) 4.3 (09.73) 4.3 (07.44) 4R (5.40) 4 (0.60) 4.50 (4.30) / (63.50) 4.3 (09.73) 4.3 (04.90) 4R (5.40) 4 (0.60) 4.6 (7.35) 3 (76.0) 4.3 (09.73) 4.03 (0.36) 4R (7.45) 5 (7.00) 6.00 (5.40) 4 (0.60) 4.7 (9.63) 4.8 (.43) 4R (03.0) 6 (5.40).75 (69.85) / (38.0) 5.50 (39.70) 4.7 (9.63) 4R (03.0) 6 (5.40) 3.38 (85.85) (50.80) 5.50 (39.70) 5.3 (3.84) 4R (03.0) 6 (5.40) 4.50 (4.30) / (63.50) 5.50 (39.70) 5.3 (30.30) 4R (03.0) 6 (5.40) 6.00 (5.40) 4 (0.60) 5.50 (39.70) 5.3 (35.3) 4R (54.00) 6 (5.40) 8.00 (03.0) 6 (5.40) 7.50 (90.50) 6.50 (65.0) Note: Other reducer combinations can be supplied upon request. F 6-Way ube rosses NOMINL FLNGE SIZE U.33 (33.78) 0.67 (7.0) 6-50-U.75 (69.85).37 (34.80) 6-50-U 4.50 (4.30).4 (56.90) U 6 (5.40).98 (75.69) U 8.00 (03.0) 3.98 (0.09) Note: ube crosses are available in other sizes upon request Typical ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 64

50 SETION.4 s & Fittings F Fittings F 4-Way rosses FLNGE TUE (33.78) 3/4 (9.05).50 (38.0) (53.85) (5.40).05 (5.07) (69.85) / (38.0).46 (6.48) (85.85) (50.80) 3. (8.79) (4.30) / (63.5) (85.85) 4-50V 4.50 (4.30) / (63.50) 4. (04.65) (7.35) 3 (76.0) 3.53 (89.66) (5.40) 4 (0.60) 4.3 (09.73) 4-400V 6.00 (5.40) 4 (0.60) 5.3 (34.87) (7.45) 5 (7.00) 4.7 (9.63) (03.0) 6 (5.40) 5.50 (39.70) 4-600V 8.00 (03.0) 6 (5.40) 6.56 (66.6) (54.00) 8 (03.0) 7.50 (90.50) (336.55) 0 (54.00) 0.00 (54.00) Rotatable Typ. Nonrotatable Typ. F 5-Way rosses Rotatable Typ. Nonrotatable Typ. FLNGE TUE (33.78) 3 /4 (9.05).50 (38.0) (53.85) (5.40).05 (5.07) (69.85) / (38.0).46 (6.48) (85.85) (50.80) 3. (8.79) (4.30) / (63.50) 3.38 (85.85) 5-50V 4.50 (4.30) / (63.50) 4. (04.65) (7.35) 3 (76.0) 3.53 (89.66) (5.40) 4 (0.60) 4.3 (09.73) 5-400V 6.00 (5.40) 4 (0.60) 5.3 (34.87) (7.45) 5 (7.00) 4.7 (9.63) (03.0) 6 (5.40) 5.50 (39.70) 5-600V 8.00 (03.0) 6 (5.40) 6.56 (66.6) (54.00) 8 (03.0) 7.50 (90.50) (336.55) 0 (54.00) 0.00 (54.00) F 6-Way rosses FLNGE TUE (33.78) 3 /4 (9.05).50 (38.0) (53.85) (5.40).05 (5.07) (69.85) / (38.0).46 (6.48) (85.85) (50.80) 3. (8.79) (4.30) / (63.50) 3.38 (85.85) 6-50V 4.50 (4.30) / (63.50) 4. (04.65) (7.35) 3 (76.0) 3.53 (89.66) (5.40) 4 (0.60) 4.3 (09.73) 6-400V 6.00 (5.40) 4 (0.60) 5.3 (34.87) (7.45) 5 (7.00) 4.7 (9.63) (03.0) 6 (5.40) 5.50 (39.70) 6-600V 8.00 (03.0) 6 (5.40) 6.56 (66.6) (54.00) 8 (03.0) 7.50 (90.50) (336.55) 0 (54.00) 0.00 (54.00) Rotatable Nonrotatable (incl. flange not shown) Typ. Typ. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 65

51 SETION.4 s & Fittings Plate Nuts Nor-al Products manufactures plate nuts for most sizes of F flanges from /3 to 0 inches (33.96 to 54mm). These handy backing nuts center themselves over two adjacent bolt holes on the back side of a flange and can be held in place with one finger while bolts are tightened with a single wrench. Plate nuts are perfect for those hard to reach (and see) spaces that are encountered during system assembly and service. Plate Nut for /3 (33.78) and 3 /4 (69.85) s D Plate Nuts FLNGE THRED SIZE D NP-075 /3 (40) (0.3) 0.3 (7.6) 0.53 (3.46) 0.5 (3.8) NP-50 3 /4 (70) (40.39) 0.5 (.70).5 (9.) 0.8 (4.57) NP-50M 3 /4 (70) M6.59 (40.39) 0.5 (.70).5 (9.) 0.8 (4.57) NP /8 (86) (44.45) 0.5 (.70).09 (7.69) 0. (5.59) NP-50 4 / (4) (5.56) 0.5 (.70).39 (35.3) 0. (5.59) NP-50M 4 / (4) M8.03 (5.56) 0.5 (.70).39 (35.3) 0. (5.59) NP /8 (7) (44.45) 0.5 (.70).5 (3.75) 0. (5.59) NP (5) (44.45) 0.5 (.70).00 (5.40) 0. (5.59) NP-400M 6 (5) M8.75 (44.45) 0.5 (.70).00 (5.40) 0. (5.59) NP (00) (44.45) 0.5 (.70). (8.45) 0. (5.59) NP-600M 8 (00) M8.75 (44.45) 0.5 (.70). (8.45) 0. (5.59) NP (54) (44.45) 0.5 (.70).9 (30.3) 0. (5.59) Plate Nut for s larger than 3 /4 (69.85) D ll plate nuts 4 per package Plate Nut ssembly Kits with Hex Head olts FLNGE DESRIPTION KNP-075 /3 (34) () Plate nuts (4) SS 8-3 x 3 /4 inch bolts and washers KNP-50 3 /4 (70) () Plate nuts (4) SS 4-8 x /4 inch bolts and washers KNP /8 (86) (6) Plate nuts (3) SS x 3 /4 inch bolts and washers KNP-50 4 / (4) (6) Plate nuts (3) SS x inch bolts and washers KNP /8 (7) (0) Plate nuts (40) SS x /4 inch bolts and washers KNP (5) (6) Plate nuts (3) SS x /4 inch bolts and washers KNP (00) (6) Plate nuts (3) SS x /4 inch bolts and washers KNP (54) (4) Plate nuts (48) SS x / inch bolts and washers ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Plate Nut ssembly Kits with -pt. olts FLNGE DESRIPTION KNP-50-3 /4 (70) () Plate nuts (4) SS -pt. 4-8 x /4 inch bolts and washers KNP /8 (86) (6) Plate nuts (3) SS -pt x 3 /4 inch bolts and washers KNP-50-4 / (4) (6) Plate nuts (3) SS -pt x inch bolts and washers KNP /8 (7) (0) Plate nuts (40) SS -pt x /4 inch bolts and washers KNP (5) (6) Plate nuts (3) SS -pt x /4 inch bolts and washers KNP (00) (0) Plate nuts (49) SS -pt x /4 inch bolts and washers KNP (54) (4) Plate nuts (48) SS -pt x / inch bolts and washers 66

52 SETION.5 s & Fittings luminum to Stainless Steel Transitions Nor-al Products luminum to Stainless Steel Transitions provide a reliable UHV seal for aluminum vacuum systems. n explosion-bonded composite of aluminum, stainless steel and two other UHV materials make these transitions leak-tight at UHV pressures. Transitions are welded to a stainless steel F flange as a complete unit ready to weld to your aluminum chamber or beamline, or the transition can be purchased separately for welding to your own F flange. The explosion bonds have been tested for tensile, shear and thermal stress. Testing included thermal quenching from 773ºK to 77 K. This process has shown vacuum integrity to better than 5 x 0-0 standard cc per second with wall thickness as thin as 0.05 inch (6.35mm). Each unit is thermally cycled to 300. Helium leak testing is done before and after thermal cycling. pplications ccelerators Synchrotrons Semiconductor processing luminum to Stainless Steel Transitions DESRIPTION D E LST-075-F Nonrotatable F.33 (33.78) 0.50 (.70) (9.05).0 (55.88).00 (5.40) LST-075 Transition only (.70) (9.05) -.00 (5.40) LST-50-F Nonrotatable F.73 (69.34).5 (3.75).500 (38.0).9 (48.5).75 (44.45) LST-50 Transition only -.5 (3.75).500 (38.0) -.75 (44.45) LST-50-F Nonrotatable F 4.47 (3.54).5 (57.5).500 (63.50).08 (5.83).75 (69.85) LST-50 Transition only -.5 (57.5).500 (63.50) -.75 (69.85) LST-400-F Nonrotatable F 5.97 (5.64) 3.75 (95.5) (0.60).4 (54.36) 4.5 (07.95) LST-400 Transition only (95.5) (0.60) (07.95) LST-600-F Nonrotatable F 7.97 (0.44) 5.75 (46.05) (5.40).0 (55.88) 6.5 (58.75) LST-600 Transition only (46.05) (5.40) (58.75) LST-800-F Nonrotatable F 9.97 (53.4) 7.75 (96.85) (03.0).0 (55.88) 8.5 (09.55) LST-800 Transition only (96.85) (03.0) (09.55) SPEIFITIONS General:Nonrotatable with clearance bolt holes Material s: 304 stainless steel (36L available upon request) Gaskets: opper, FKM or silver plated olts: 8-8 stainless steel or silver plated Torque:.5 Nm. Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º E E.5" (6.35) luminum.5" (6.35) D Stainless Steel 45.70" (43.8) hamfer.00"(.5) x 45 F ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 67

53 SETION.6 s & Fittings Wire Seal s SPEIFITIONS General: Nonrotatable flanges with clearance bolt holes Nominal sizes: 3 /8 to 7 /8 inches (34 to 689mm) Tube sizes: 0 to 4 inches (54 to 609.6mm) Materials : 304 stainless steel (36L available on request) Gaskets: opper olts: 8-8 stainless steel Vacuum range: x 0-3 mbar - UHV Temperature range: -00º to 450º Wire Seal ssembly Instructions. pply a small amount of high temperature anti-seize compound to the bolt threads.. heck that both flange surfaces are clean and sealing edges are free from nicks and scratches. 3. Using clean, lint free gloves, unpack gasket. 4. Place seal over the sealing area on the male flange. 5. lign the mating flange hole pattern and leak test grooves. 6. Install the proper bolts and tighten hand tight. heck to see that the flange faces are parallel. 7. Tighten the bolts /4 to / turns using a circular clockwise pattern until the flange faces are metal to metal. 8. Torque the fasteners until leak tight using the same pattern. Never exceed maximum torque. Wire Seal Female lank Nor-al Products wire seal flanges are designed for use on bell jars, custom vacuum chambers and related systems. Standard sizes range from to 7 inch (305 to 686mm) nominal for tube sizes from 0 to 4 inch (54 to 609.6mm). male and female flange compress a inch (0.3mm) diameter OFH copper wire to effect a seal. Gasket flow is confined by the geometry of the flange surfaces to the area of the seal. Minor nicks and scratches within this contact area are filled with crushed copper wire providing a seal that is leak tight at 0-3 mbar after repeated bake out to 450. Solid blanks are standard. Dished head blanks are offered as a lower cost alternative. Wire Seal s D E F WS--000M.375 (34.33) (8.70) (88.) 4 WS--000M.375 (34.33) (47.65) 0.00 (54.5).3 (8.70) (6.00).343 (88.) 4 WS--000F.375 (34.33) (8.70) (88.) 4 WS--000F.375 (34.33) (47.65) 0.00 (54.5).3 (8.70) (6.00).343 (88.) 4 WS-4-000M 4.65 (37.48) (8.70) (345.6) 3 WS-4-00M 4.65 (37.48).750 (98.45).00 (305.3).3 (8.70) (6.00) (345.6) 3 WS-4-000F 4.65 (37.48) (8.70) (345.6) 3 WS-4-00F 4.65 (37.48).750 (98.45).00 (305.3).3 (8.70) (6.00) (345.6) 3 WS-7-000M 7.50 (438.5) (8.70) (399.4) 36 WS-7-400M 7.50 (438.5) (349.5) 4.00 (356.).3 (8.70) (6.00) 5.78 (399.4) 36 WS-7-000F 7.50 (438.5) (8.70) (399.4) 36 WS-7-400F 7.50 (438.5) (349.5) 4.00 (356.).3 (8.70) (6.00) 5.78 (399.4) 36 WS-9-000M 9.56 (496.87) (33.7) (454.03) 36 WS-9-600M 9.56 (496.87) (400.05) 6.00 (406.9).3 (33.7) (6.00) (454.03) 36 WS-9-000F 9.56 (496.87) (33.7) (454.03) 36 WS-9-600F 9.56 (496.87) (400.05) 6.00 (406.9).3 (33.7) (6.00) (454.03) 36 WS--000M.5 (56.98) (38.0) (5.75) 36 WS--800M.5 (56.98) (450.85) 8.00 (457.7).50 (38.0).000 (5.40) 0.87 (5.75) 36 WS--000F.5 (56.98) (38.0) (5.75) 36 WS--800F.5 (56.98) (450.85) 8.00 (457.7).50 (38.0).000 (5.40) 0.87 (5.75) 36 WS-7-000M 7.5 (688.98) (44.45) (656.4) 40 WS-7-400M 7.5 (688.98) 3.65 (600.08) 4.00 (60.).75 (44.45).5 (8.58) (656.4) 40 WS-7-000F 7.5 (688.98) (44.45) (656.4) 40 WS-7-400F 7.5 (688.98) 3.65 (600.08) 4.00 (60.).75 (44.45).5 (8.58) (656.4) 40 Model Number Definitions M = Male flange F = Female flange Female lank F D Male lank F OLT HOLES D Female ored Male ored Male ored E D E D Torque Specifications NOMINL OLT SIZE MX. TORQUE NM (305) 3 / (356) 3/ (43) / (483) / (559) 5 / (686) 5 / ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Wire Seal Gaskets and olt Sets F FLNGE DESRIPTION QUNTITY WG-.375 (34.33) opper gasket W-.375 (34.33) SS x bolts and nuts 4 WG (37.48) opper gasket W (37.48) SS x bolts and nuts 3 WG (438.5) opper gasket W (438.5) SS -0 x 3 4 bolts and nuts 36 WG (496.87) opper gasket W (496.87) SS -0 x 3 bolts and nuts 36 WG-.5 (56.98) opper gasket W-.5 (56.98) SS x 3 bolts and nuts 36 WG (688.98) opper gasket W (688.98) SS x 4 bolts and nuts 40 F 68

54 s & Fittings EV omponents General Information SETION.7 SPEIFITIONS Tube sizes: 3 /4 to 4 inches (9.05 to 0.6mm) Materials : 304 stainless steel Seal: luminum Vacuum range: > x 0 - mbar - UHV Temperature range: -70º to 50º Nor-al Products stocks a complete line of EV chain clamps and aluminum metal seals for converting elastomer seal NW (KF) and ISO flanges to UHV metal seals. They provide a number of benefits over elastomer seals: reduced outgassing, no permeation, no hydrocarbons, resistance to radiation and short half-life. luminum seals are used in high-energy physics, other UHV applications and cryogenic applications. luminum seals are reliable in high vibration or temperature cycling environments. hain clamps and NW flanges are the standard vacuum flange for many Japanese semiconductor equipment manufacturers. The advantages over using the standard ISO flange are the time and space savings during assembly and the flexibility to form high vacuum or UHV seals. To install a metal seal on an existing NW flange, simply remove the standard clamp, centering ring and O-ring assembly. Replace them with an aluminum knife edge seal and chain clamp. (See diagram). Standard ISO claw clamps can be used with aluminum seals to convert ISO flanges from high vacuum to UHV. Nor-al Products large NW flanges are available in 63, 80 and 00 NW sizes from stock. hain clamps are used to form either elastomer or metal seals with large NW flanges. hain lamp luminum Knife Edge Seal EV luminum Metal Seals luminum seals locate on the centering ring groove (inner centering) or outside edge of the flange (outer centering) depending on the size. (Inner and outer centering versions are available for all NW flange sizes.) luminum knifeedges are compressed by the flange sealing surfaces when the chain clamp or ISO claw clamp is tightened. The resultant seal has a helium leak rate of less than x0 - standard mbar l/sec and can be baked repeatedly to 50. The aluminum alloy is soft enough to make a good seal with reasonable force but will not flow at moderate temperatures. luminum Seals will even work with aluminum flanges. EV Large NW s Nor-al Products offers blank and bored NW-63, NW-80 and NW-00 flanges that are compatible with other manufacturers large QF/KF flanges made to the ISO 96 specification. They can be used with chain clamps to form elastomer or aluminum metal seals. Elastomer seals are formed with standard ISO centering ring/o-ring assemblies and elastomer chain clamps. UHV connections are formed with aluminum metal seals and chain clamps. NW flanges are made from 304 stainless steel for.5 to 4.0 inch (63.5 to 0.6mm) tube sizes. s for tube sizes up to 8 inches (7.mm), metric tube sizes can be supplied. EV efix s, Seals, hain lamps & Fittings Nor-al Products now offers efix connections in sizes NW6 up to NW50. all for more information. The efix system enables reaching XHV leakproof connections within seconds. The main difference between the F and efix systems is found in the compression of the metal gasket. The F knife edge makes a circular imprint into the gasket causing one time usability. The efix system creates a completely particle-free -pressing mechanism that allows seals to be reused. further advantage of the wide overlapping area with a wide cross section is its extensive thermocycling capability with a sheer range of -7 to (usually breaking the fragile F knife edge after one cycle). This technology requires only 50% of the F compression force at the seal surface in order to achieve gas-tight intermetallic diffusion bonds. pplications & enefits: UHV applications up to 0 - mbar Pressurized applications up to 300 bar ryo applications down to Oven applications up to (copper seals) efix system registered by EV seals reusable up to 0 times (provided no scratches) 36L stainless steel for nuclear and military applications 69

55 SETION.7 s & Fittings EV Metal Seals.75/.57 Diagram (4.445/3.734).098/.079 (.489/.007) Diagram.76 (7.00).36 (5.994) EV luminum Metal Seals with Outer entering Ring for NW-6 to NW-50 Tapered s DIGRM FLNGE Z NW-0/6.8 (9.97) 0.79 (0.00) 0.9 (3.) Z NW-0/5.58 (40.3).6 (3.00).30 (33.0) Z NW-3/40.6 (54.86).77 (40.3).89 (48.0) Z NW (75.00).56(65.00).68 (68.00) Z NW (87.00) 3.03 (77.00) 3.4 ( /.57 (4.394/3.988) Diagram.76 (7.00) EV luminum Metal Seals with Inner entering Ring for NW-6 to NW-50 Tapered s DIGRM FLNGE IZ NW (7.00) 0.60 (5.00) 0.83 (.00) IZ NW-5.0 (6.00) 0.94 (4.00).8 (30.00) IZ NW-40.6 (4.00).54 (39.00).85 (47.00) IZ NW (5.00).97 (50.00).3 (59.00) IZ NW (70.00).68 (68.00) 3.03 (77.00) NW (83.00) 4.49 (4.00) 3.54 (90.00) NW (0.00) 5.8 (34.00) 4.9 (09.00) NW ( (90.00) 6.30 (60.00) NW ( (5.00) 8.66 (0.00) NW (6.00).85 (30.00) 0.55 (68.00).77/.57 (4.496/3.988).76 (7.00) EV luminum Metal Seals with Outer entering Ring for ISO-63 to ISO-50 s FLNGE TORQUE LMPS* ISO (95.00) 3.47 (88.4).3 Nm ISO (09.98) 4.06 (03.).3 Nm ISO (30.05) 4.84 (.94).3 Nm 8 *Use with Nor-al Products ISO double or single claw clamps. ll dimensions are in inches and (mm) unless otherwise noted 70

56 s & Fittings EV Tapered s SETION.7 EV NW-63 to NW-50 Tapered s DESRIPTION D E lank 3.43 (87.) -.76 (70.0) lank 4.49 (4.05) (83.06) lank 5.8 (34.) (0.) ored for / inch (63mm) tube 3.43 (87.).44 (6.98).76 (70.0).5 (63.75).7 (68.83).470 (.938) D E.00 (5.080).50 (6.350) ored for 3 inch (75mm) tube 4.49 (4.05).87 (7.90) 3.7 (83.06) 3.0 (76.45) 3.8 (97.03) ored for 4 inch (00mm) tube 5.8 (34.) 3.87 (98.30) 4.0 (0.) 4.0 (0.85) 4.6 (7.09).453 (.506).787 (9.990).590 (4.986) D E 7

57 SETION.7 s Diagram.787 (9.990) & Fittings EV hain lamps Nor-al Products stocks chain clamps for NW flanges in two styles: one with PTFE coated aluminum links and an uncoated version. The less expensive uncoated version is the preferred choice for sealing standard NW flanges with aluminum metal seals. The uncoated chain clamps can be used with NW flanges that have a radius of approximately.060 of an inch (.5mm) on the outer edge of the nonsealing side. Radius.060 Most manufacturers NW flanges have this feature. If the flanges to be sealed have a sharp edge, the PTFE coated chain clamps are required to ensure adequate sealing force for aluminum metal seals. oth versions use a single, hex head nut for closure. Stainless steel chain clamps and low cost composite chain clamps are available for elastomer NW connections. hain clamps for NW-63 flanges are similar to the NW-6 to 50 sizes. The style to use with NW-63 elastomer seals has a single knob for tightening. The clamp used for sealing aluminum metal seals has a single hex head nut. oth have uncoated aluminum links, although PTFE coated aluminum versions are available. hain clamps for 80 to 00mm flanges are stocked in two styles: one with a single knob for elastomer seals and another with two allen head bolts for aluminum metal seals. lthough chain clamps are bakeable to 50, the knobs should not be baked above 60. hain clamps for tube sizes up to 8 inch (7mm) can be supplied on request. Diagram.57 (3.988).787 (9.990) EV hain lamps for NW-6 to NW-63 s luminum Links FLNGE SIZE NO. OF LINKS DIGRM PPLITION MX. TEMP. TORQUE ELSTOMER / METL /6 3 Metal or Elastomer Seals 4.53 (5.06).36 (59.94) Nm /.486 Nm /5 3 Metal or Elastomer Seals 4.9 (4.97).76 (70.0) Nm /.938 Nm /40 4 Metal or Elastomer Seals 5.3 (35.3) 3.35 (85.09) Nm / Nm Metal or Elastomer Seals 5.98 (5.89) 4.3 (04.90) Nm / 4.97 Nm Metal or Elastomer Seals 6.30(60.0) 4.7(9.89) Nm / 4.97 Nm Diagram.57 (3.988) (38.0) EV hain lamps for NW-6 to NW-63 s - PTFE oated Links * FLNGE SIZE NO. OF LINKS DIGRM PPLITION MX. TEMP. TORQUE ELSTOMER / METL /6 3 No radius, metal/elastomer 4.53 (5.06).36 (59.94) Nm /.486 Nm /5 3 No radius, metal/elastomer 4.9 (4.97).76 (70.0) Nm /.938 Nm /40 4 No radius, metal/elastomer 5.3 (35.3) 3.35 (85.09) Nm / Nm No radius, metal/elastomer 5.98 (5.89) 4.3 (04.90) Nm / 4.97 Nm No radius, metal/elastomer 6.30(60.0) 4.7(9.89) Nm / 4.97 Nm *Not radiation resistant EV hain lamps for NW-63 to NW-50 s FLNGE SIZE DIGRM PPLITION MX. TEMP. TORQUE ELSTOMER/METL Elastomer seals only 6.69 (69.93) 4.7 (9.89) Nm D Elastomer seals only 9.6 (44.09) 6.06 (53.9) Nm D Elastomer seals only 0.08 (56.03) 6.77 (7.98) Nm Diagram D (38.0) ll dimensions are in inches and (mm) unless otherwise noted 7

58 dapter Fittings General Information SETION.8 dapter Fittings Nor-al Products provides a broad range of adapter fittings in order to connect two dissimilar types of components. They are made from 304 or 36L stainless steel and are TIG welded, cleaned and leak checked for vacuum service. Tube finishes are normally bead blasted. However, tumbled or electropolished finish can be provided upon request. s and nipples used to adapt different sizes of the same flange type are called reducers. They are listed in the flanges and fittings section for the particular flange type. For example, F zero length reducer flanges are listed in the F section of s and Fittings. SPEIFITIONS Materials: 304 or 36L stainless steel Vacuum range Metal seal: > x 0-3 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature range Metal seal: -00º to 450º Elastomer seal: -0º to 50º -to- dapters -to-flange adapter fittings are used as a transition between two dissimilar flange types. We offer adapter fittings with flange combinations for F (onflat), NW (ISO-KF), ISO and S (NSI) components as standards. We frequently provide other flange combinations as specials. These include wire seal, JIS, MES, and other flanges. -to-flange adapter nipples usually have a short length of straight tubing between the two flanges. Where possible, we offer conical adapters as an option to reduce conductance loss at the opening of the larger flange. Nor-al Products also offers adapter tees and crosses with ISO and NW flanges. S to F adapter flanges are also found in this section. -to-fitting dapters -to-fitting adapters are commonly used on chamber ports to connect flanges to special fittings. Nor-al Products offers these with F, NW, ISO and S flanges for Swagelok, male and female VR, quick disconnect, male and female NPT, ball socket and Welch pump fittings as standards. Other combinations can be supplied quickly as specials. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 73

59 dapter SETION.8 Fittings -to- NW to F onical dapter Nipples FLNGE TYPE NOM. TUE FLNGE TYPE NOM. TUE N-NW-6- NW-6 3 /4 (9.05). F (5.40).69 (4.93) N-NW-6-75 NW-6 3 /4 (9.05).75 F / (38.0).73 (69.34) N-NW-5-33 NW-5 (5.40).33 F 3 /4 (9.05).03 (5.56) N-NW-5-75 NW-5 (5.40).75 F / (38.0).73 (69.34) N-NW NW-5 (5.40) 3.38 F (50.80).75 (69.85) N-NW NW-40 / (38.0).33 F 3 /4 (9.05) 3.03 (76.96) N-NW-40- NW-40 / (38.0). F (5.40).69 (68.33) N-NW NW-40 / (38.0) 3.38 F (50.80).75 (69.85) N-NW NW-40 / (38.0) 4.50 F / (63.50).90 (73.66) N-NW NW-40 / (38.0) 4.6 F 3 (76.0) 4.06 (03.) N-NW-50- NW-50 (50.80). F (5.40).69 (68.33) N-NW NW-50 (50.80).75 F / (38.0).73 (69.34) N-NW NW-50 (50.80) 4.50 F / (63.50).90 (73.66) N-NW NW-50 (50.80) 4.6 F 3 (76.50) 4.06 (03.) N-NW NW-50 (50.80) 6.00 F 4 (0.60) 4. (06.93) NW to F dapter Nipples FLNGE TYPE FLNGE TYPE NOM. TUE N-NW-0-33 NW-0.33 F / (.70) N-NW-6-33 NW-6.33 F 3 /4 (9.05) N-NW-5- NW-5. F (5.40) N-NW NW F / (38.0) N-NW NW F 3/4 (9.05) N-NW NW F (50.80).00 (50.8) NW to S onical dapter Nipples FLNGE TYPE NOM. TUE FLNGE TYPE NOM. TUE N-NW-5-S-5 NW-5 (5.40) S-5 (50.80).78 (70.6) N-NW-40-S-5 NW-40 / (38.0) S-5 / (63.50).78 (70.6) N-NW-40-S-6 NW-40 / (38.0) S-6 3 (76.0) 4.03 (0.36) N-NW-50-S-5 NW-50 (50.80) S-5 / (63.50).78 (70.6) N-NW-50-S-6 NW-50 (50.80) S-6 3 (76.0) 4.03 (0.36) N-NW-50-S-7.5 NW-50 (50.80) S (0.60) 4.03 (0.36) NW to S dapter Nipples SPEIFITIONS Materials: 304 stainless steel (36L available upon request) Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 50º FLNGE TYPE FLNGE TYPE NOM. TUE N-NW-6-S-5 NW-6 S-5 3 /4 (9.05) N-NW-6-S-6 NW-6 S-6 3 /4 (9.05) N-NW-6-S-7.5 NW-6 S /4 (9.05) N-NW-6-S-9 NW-6 S-9 3 /4 (9.05) N-NW-6-S- NW-6 S- 3 /4 (9.05) N-NW-5-S-6 NW-5 S-6 (5.40) N-NW-5-S-7.5 NW-5 S-7.5 (5.40) N-NW-5-S-9 NW-5 S-9 (5.40) N-NW-5-S- NW-5 S- (5.40) N-NW-40-S-7.5 NW-40 S-7.5 / (38.0) N-NW-40-S-9 NW-40 S-9 / (38.0) N-NW-40-S- NW-40 S- / (38.0) N-NW-50-S-9 NW-50 S-9 (50.80) N-NW-50-S- NW-50 S- (50.80) Note: dd suffix -G to model number if O-Ring Groove is required on S flange. all for S groove prices..00 (50.8) 74

60 dapter Fittings -to- SETION.8 NW to ISO onical dapter Nipples FLNGE TYPE NOM. TUE FLNGE TYPE NOM. TUE N-NW-40-ISO-63 NW-40 / (38.0) ISO-63 / (63.50).78 (70.6) N-NW-40-ISO-80 NW-40 / (38.0) ISO-80 3 (76.0) 4.03 (0.36) N-NW-50-ISO-63 NW-50 (50.80) ISO-63 / (63.50).78 (70.6) N-NW-50-ISO-80 NW-50 (50.80) ISO-80 3 (76.0) 4.03 (0.36) N-NW-50-ISO-00 NW-50 (50.80) ISO-00 4 (0.60) 4.03 (0.36) NW to ISO dapter Nipples.75 (44.45) FLNGE TYPE NW to ISO dapter Tees FLNGE TYPE NOM. TUE N-NW-6-ISO-63-OF NW-6 ISO-63 3 /4 (9.05) N-NW-5-ISO-63-OF NW-5 ISO-63 (5.40) N-NW-5-ISO-80-OF NW-5 ISO-80 (5.40) N-NW-5-ISO-00-OF NW-5 ISO-00 (5.40) N-NW-40-ISO-00-OF NW-40 ISO-00 / (38.0) N-NW-50-ISO-60-OF NW-50 ISO-60 (50.80) FLNGE FLNGE TYPE NOM. TUE TYPE NOM. TUE (8.55) (73.66) (88.90) (80.0) (04.90) (9.7) (36.65) (8.) (8.55) (86.36) (88.90) (9.7) (04.90) (05.4) (36.65) (30.8) 3T-NW-40-ISO-63-OF ISO-63 / (63.50) NW-40 / (38.0) 3T-NW-40-ISO-80-OF ISO-80 3 (76.0) NW-40 / (38.0) 3T-NW-40-ISO-00-OF ISO-00 4 (0.60) NW-40 / (38.0) 3T-NW-40-ISO-60-OF ISO-60 6 (5.40) NW-40 / (38.0) 3T-NW-50-ISO-63-OF ISO-63 / (63.50) NW-50 (50.80) 3T-NW-50-ISO-80-OF ISO-80 3 (76.0) NW-50 (50.80) 3T-NW-50-ISO-00-OF ISO-00 4 (0.60) NW-50 (50.80) 3T-NW-50-ISO-60-OF ISO-60 6 (5.40) NW-50 (50.80) 3 Typ. NW to ISO dapter rosses 4 Typ. Typ. 3 FLNGE FLNGE TYPE NOM. TUE TYPE NOM. TUE 4-NW-40-ISO-63-OF ISO-63 / (63.50) NW-40 / (38.0) 3.5 (8.55).90 (73.66) 4-NW-40-ISO-80-OF ISO-80 3 (76.0) NW-40 / (38.0) 3.50 (88.90) 3.5 (80.0) 4-NW-40-ISO-00-OF ISO-00 4 (0.60) NW-40 / (38.0) (04.90) (9.7) 4-NW-40-ISO-60-OF ISO-60 6 (5.4) NW-40 / (38.0) (36.65) (8.) 4-NW-50-ISO-63-OF ISO-63 / (63.50) NW-50 (50.80) 3.5 (8.55) 3.40 (86.36) 4-NW-50-ISO-80-OF ISO-80 3 (76.0) NW-50 (50.80) 3.50 (88.90) 3.65 (9.7) 4-NW-50-ISO-00-OF ISO-00 4 (0.60) NW-50 (50.80) (04.90) (05.4) 4-NW-50-ISO-60-OF ISO-60 6 (5.40) NW-50 (50.80) (36.65) (30.8) SPEIFITIONS Materials: 304 stainless steel (36L available upon request) Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 75

61 dapter SETION.8 Fittings -to- F to ISO onical dapter Nipples FLNGE FLNGE TYPE NOM. TUE TYPE NOM. TUE N-75-ISO-63-OF.75 F / (40) ISO-63-OF / (63).83 (7.88) N-75-ISO-80-OF.75 F / (40) ISO-80-OF 3 (75) 4.08 (03.63) N-338-ISO-63-OF 3.38 F (50) ISO-63-OF / (63).85 (7.39) N-338-ISO-80-OF 3.38 F (50) ISO-80-OF 3 (75) 4.0 (04.4) N-338-ISO-00-OF 3.38 F (50) ISO-00-OF 4 (00) 4.0 (04.4) N-450-ISO-80-OF 4.50 F / (63) ISO-80-OF 3 (75) 4.5 (07.95) N-450-ISO-00-OF 4.50 F / (63) ISO-00-OF 4 (00) 4.5 (07.95) N-46-ISO-63-OF 4.6 F 3 (75) ISO-63-OF / (63) 4.6 (05.66) N-46-ISO-00-OF 4.6 F 3 (75) ISO-00-OF 4 (00) 4.6 (05.66) N-600-ISO-63-OF 6.00 F 4 (00) ISO-63-OF / (63) 4.3 (09.47) N-600-ISO-80-OF 6.00 F 4 (00) ISO-80-OF 3 (75) 4.3 (09.47) F to ISO dapter Nipples FLNGE TYPE FLNGE TYPE NOM. TUE N-450-ISO-63-OF 4.50 F ISO-63-OF / (63.50) N-46-ISO-80-OF 4.6 F ISO-80-OF 3 (76.0) N-600-ISO-00-OF 6.00 F ISO-00-OF 4 (0.60) N-800-ISO-60-OF 8.00 F ISO-60-OF 6 (5.40) N-000-ISO-00-OF 0.00 F ISO-00-OF 8 (03.0) ISO to S onical dapter Nipples FLNGE TYPE NOM. TUE FLNGE TYPE NOM. TUE N-ISO-63-OF-S-5 ISO-63 / (63.50) S-5 (50.80).88 (73.5) N-ISO-63-OF-S-6 ISO-63 / (63.50) S-6 3 (76.0) 4.3 (04.90) N-ISO-63-OF-S-7.5 ISO-63 / (63.50) S (0.60) 4.3 (04.90) N-ISO-80-OF-S-5 ISO-80 3 (76.0) S-5 (50.80) 4.3 (04.90) N-ISO-80-OF-S-7.5 ISO-80 3 (76.0) S (0.60) 4.3 (04.90) N-ISO-00-OF-S-5 ISO-00 4 (0.60) S-5 (50.80) 4.3 (04.90) N-ISO-00-OF-S-6 ISO-00 4 (0.60) S-6 3 (76.0) 4.3 (04.90) Note: dd suffix -G to model number if O-ring groove is required on S flange. all for groove prices SPEIFITIONS Materials: 304 or stainless steel (36L available upon request) Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 50º ISO to S dapter Nipples FLNGE TYPE FLNGE TYPE NOM. TUE N-ISO-63-OF-S- ISO-63 S- / (63.50) N-ISO-80-OF-S-6 ISO-80 S-6 3 (76.0) N-ISO-80-OF-S- ISO-80 S- 3 (76.0) N-ISO-00-OF-S-7.5 ISO-00 S (0.60) N-ISO-00-OF-S-9 ISO-00 S-9 4 (0.60) N-ISO-00-OF-S- ISO-00 S- 4 (0.60) N-ISO-60-OF-S-9 ISO-60 S-9 6 (5.40) N-ISO-60-OF-S- ISO-60 S- 6 (5.40) N-ISO-00-OF-S- ISO-00 S- 8 (03.0) N-ISO-00-OF-S-3.5 ISO-00 S (03.0) Note: dd suffix -G to model number if O-ring groove is required on S flange. all for groove prices. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 76

62 dapter Fittings -to- SETION.8 F to S onical dapter Nipples FLNGE TYPE NOM. TUE FLNGE TYPE NOM. TUE N--S-5. F (5.40) S-5 (50.80).79 (70.87) N-75-S-5.75 F / (38.0) S-5 (50.80).83 (7.88) N-75-S-6.75 F / (38.0) S-6 3 (76.0) 4.08 (03.63) N-338-S F (50.80) S-5 / (63.50).85 (7.38) N-338-S F (50.80) S-6 3 (76.0) 4.0 (04.4) N-338-S F (50.80) S (0.60) 4.0 (04.4) N-450-S F (50.80) S-5 (50.80) 3.00 (76.0) N-450-S F / (63.50) S-6 3 (76.0) 4.5 (07.95) N-450-S F / (63.50) S (0.60) 4.5 (07.95) N-46-S F 3 (76.0) S-5 (50.80) 4.6 (05.66) N-46-S F 3 (76.0) S (0.60) 4.6 (05.66) N-600-S F 4 (0.60) S-5 (50.80) 4.3 (09.47) N-600-S F 4 (0.60) S-6 3 (76.0) 4.3 (09.47) Non-Rotatable Rotatable Note: dd suffix -G to model number if O-ring groove is required on S flange. all for groove prices. Rotatable Non-Rotatable F to S dapter Nipples FLNGE TYPE FLNGE TYPE NOMINL TUE N-33-S-5.33 F S-5 3 /4 (9.05) N-33-S-6.33 F S-6 3 /4 (9.05) N--S-6. F S-6 (5.40) N-46-S F S-6 3 (76.0) N-33-S F S /4 (9.05) N--S-7.5. F S-7.5 (5.40) N-75-S F S-7.5 / (38.0) N-33-S-9.33 F S-9 3/4 (9.05) N--S-9. F S-9 (5.40) N-75-S-9.75 F S-9 / (38.0) N-338-S F S-9 (50.80) N-450-S F S-9 / (63.50) N-46-S F S-9 3 (76.0) N-600-S F S-9 4 (0.60) N-33-S-.33 F S- 3 /4 (9.05) N--S-. F S- (5.40) N-75-S-.75 F S- / (38.0) N-338-S F S- (50.80) N-450-S F S- / (63.50) N-46-S- 4.6 F S- 3 (76.0) N-600-S F S- 4 (0.60) N-800-S F S- 6 (5.40) N-33-S F S /4 (9.05) N--S-3.5. F S-3.5 (5.40) N-75-S F S-3.5 / (38.0) N-338-S F S-3.5 (50.80) N-450-S F S-3.5 / (63.50) N-46-S F S (76.0) N-600-S F S (0.60) N-800-S F S (5.40) N-000-S F S (03.0) N-33-S-6.33 F S-6 3/4 (9.05) N--S-6. F S-6 (5.40) N-75-S-6.75 F S-6 / (38.0) N-338-S F S-6 (50.80) N-450-S F S-6 / (63.50) N-46-S F S-6 3 (76.0) N-600-S F S-6 4 (0.60) N-800-S F S-6 6 (5.40) N-000-S F S-6 8 (03.0) N-35-S F S-6 0 (54.00) SPEIFITIONS Materials: 304 or stainless steel (36L available upon request) Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Note: dd suffix -G to model number if O-ring groove is required on S flange. all for groove prices. 77

63 dapter SETION.8 Fittings dapter and -to-fitting SPEIFITIONS Materials: 304 stainless steel Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 50º Large Detail Small Detail F to S dapter s SMLL FLNGE LRGE FLNGE S Z NT S-5-000N 0.63 (6.00) 0.50 (.70) S-5--00Z -000NT S-5-000N.00 (5.40) 0.50 (.70) S Z NT S-5-000N.50 (38.0) 0.50 (.70) S Z NT S-6-000N 0.63 (6.00) 0.50 (.70) S-6--00Z -000NT S-6-000N.00 (5.40) 0.50 (.70) S Z NT S-6-000N.50 (38.0) 0.50 (.70) S Z NT S-6-000N.00 (50.80) 0.75 (9.05) S Z NT S N 0.63 (6.00) 0.50 (.70) S Z -000NT S N.00 (5.40) 0.50 (.70) S Z NT S N.50 (38.0) 0.50 (.70) S Z NT S N.00 (50.80) 0.75 (9.05) S Z NT S N.50 (63.50) 0.75 (9.05) S Z NT S-9-000N 0.63 (6.00) 0.75 (9.05) S-9--00Z -000NT S-9-000N.00 (5.40) 0.75 (9.05) S Z NT S-9-000N.50 (38.0) 0.75 (9.05) S Z NT S-9-000N.00 (50.80) 0.75 (9.05) S Z NT S-9-000N.50 (63.50) 0.75 (9.05) S Z NT S-9-000N 3.00 (76.0) 0.75 (9.05) S Z NT S-9-000N 4.00 (0.60) 0.75 (9.05) S Z NT S--000N 0.63 (6.00) 0.75 (9.05) S---00Z -000NT S--000N.00 (5.40) 0.75 (9.05) S Z NT S--000N.50 (38.0) 0.75 (9.05) S Z NT S--000N.00 (50.80) 0.75 (9.05) S Z NT S--000N.50 (63.50) 0.75 (9.05) S Z NT S--000N 3.00 (76.0) 0.75 (9.05) S Z NT S--000N 4.00 (0.60) 0.75 (9.05) S Z NT S--000N 6.00 (5.40) 0.75 (9.05) SPEIFITIONS Materials: 304 stainless steel Vacuum range: > x 0-8 mbar - High vacuum Temperature range: -0º to 50º NW Welch Pump dapters USE WITH WELH PUMP THRED TUE ID N-NW , 400, 40 3 /8-8 NPSM x (.43) N-NW /4-0 NPSM x (4.8) N-NW /4-0 NPSM x (4.8) N-NW , 40, 403, 8806, 88, 886, 88-0 NPSM x (9.05) N-NW , 40, 403, 8806, 88, 886, 88-0 NPSM x (9.05) N-NW , 376, 883 /- NPSM x.00.5 (8.58) N-NW , /4-0 NPSM x (34.93) N-NW , /4-0 NPSM x (34.93) Note: Includes aluminum gasket ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 78

64 dapter Fittings -to-fitting SETION.8 NW Female Pipe dapters NPT NW-0- /8 FPT /8 (3.8) 0.9 (3.37) NW-6- /8 FPT /8 (3.8) 0.9 (3.37) NW-5- /8 FPT /8 (3.8) 0.9 (3.37) NW-40- /8 FPT /8 (3.8) 0.9 (3.37) NW-50- /8 FPT /8 (3.8) 0.9 (3.37) NW-0- /4 FPT /4 (6.35).07 (7.8) NW-6- /4 FPT /4 (6.35).07 (7.8) NW-5- /4 FPT /4 (6.35).07 (7.8) NW-40- /4 FPT /4 (6.35).07 (7.8) NW-50- /4 FPT /4 (6.35).07 (7.8) NW-6- / FPT / (.70).44 (36.58) NW-5- / FPT / (.70).39 (35.3) NW-40- / FPT / (.70).39 (35.3) NW-50- / FPT / (.70).39 (35.3) NW-5-3 /4 FPT 3 /4 (9.05).45 (36.83) NW-40-3 /4 FPT 3 /4 (9.05).45 (36.83) NW-50-3 /4 FPT 3/4 (9.05).45 (36.83) NW-5- FPT (5.40).57 (39.88) NW-40- FPT (5.40).57 (39.88) NW-50- FPT (5.40).57 (39.88) SPEIFITIONS Materials s: 304 stainless steel NPT Fittings: 36L stainless steel Vacuum range: > x 0-6 mbar - High vacuum Temperature range: -0º to 50º Female NPT NW NW Machined NW Female Pipe dapters NPT FLT NW-6- /8-FPTM /8 (3.8).65 (5.88) 0.75 (9.05) NW-6- /4-FPTM /4 (6.35).65 (5.88) 0.75 (9.05) NW-5- /8-FPTM /8 (3.8).875 (.3).00 (5.40) NW-5- /4-FPTM /4 (6.35).875 (.3).00 (5.40) NW-40- /8-FPTM /8 (3.8).5 (3.75).50 (38.0) NW-40- /4-FPTM /4 (6.35).5 (3.75).50 (38.0) NW Male Pipe dapters NPT NW-0- /8 MPT /8 (3.8) 0.89 (.6) NW-6- /8 MPT /8 (3.8) 0.89 (.6) NW-5- /8 MPT /8 (3.8) 0.89 (.6) NW-40- /8 MPT /8 (3.8) 0.89 (.6) NW-50- /8 MPT /8 (3.8) 0.89 (.6) NW-0- /4 MPT /4 (6.35).0 (7.94) NW-6- /4 MPT /4 (6.35).0 (7.94) NW-5- /4 MPT /4 (6.35).0 (7.94) NW-40- /4 MPT /4 (6.35).0 (7.94) NW-50- /4 MPT /4 (6.35).0 (7.94) NW-6- / MPT / (.70).35 (34.9) NW-5- / MPT / (.70).35 (34.9) NW-40- / MPT / (.70).35 (34.9) NW-50- / MPT / (.70).35 (34.9) NW-5-3 /4 MPT 3 /4 (9.05).35 (34.9) NW-40-3 /4 MPT 3 /4 (9.05).35 (34.9) NW-50-3 /4 MPT 3 /4 (9.05).35 (34.9) NW-5- MPT (5.40).64 (4.66) NW-40- MPT (5.40).64 (4.66) NW-50- MPT (5.40).64 (4.66) Male NPT NW ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 79

65 dapter SETION.8 Fittings -to-fitting NW Female VR dapters Female VR NW FLNGE TYPE VR SIZE NW-0- /4 FVR NW-0 /4 (6.35).46 (37.08).96 (49.78) NW-6- /4 FVR NW-6 /4 (6.35).46 (37.08).96 (49.78) NW-5- /4 FVR NW-5 /4 (6.35).46 (37.08).96 (49.78) NW-40- /4 FVR NW-40 /4 (6.35).46 (37.08).96 (49.78) NW-50- /4 FVR NW-50 /4 (6.35).46 (37.08).96 (49.78) NW-6-3 /8 FVR NW-6 3/8 (9.53).65 (4.9).0 (55.88) NW-5-3 /8 FVR NW-5 3/8 (9.53).65 (4.9).0 (55.88) NW-40-3 /8 FVR NW-40 3 /8 (9.53).65 (4.9).0 (55.88) NW-50-3 /8 FVR NW-50 3 /8 (9.53).65 (4.9).0 (55.88) NW-6- / FVR NW-6 / (.70).65 (4.9).0 (55.88) NW-5- / FVR NW-5 / (.70).65 (4.9).0 (55.88) NW-40- / FVR NW-40 / (.70).65 (4.9).0 (55.88) NW-50- / FVR NW-50 / (.70).65 (4.9).0 (55.88) F Female VR dapters FLNGE TYPE VR SIZE 33-4 FVR.33 F /4 (6.35).36 (34.54).88 (47.75) FVR.33 F 3 /8 (9.53).55 (39.37).3 (54.0) 75-4 FVR.75 F /4 (6.35).36 (34.54).88 (47.75) FVR.75 F 3 /8 (9.53).55 (39.37).3 (54.0) Female VR F Male VR NW NW Male VR dapters FLNGE SIZE VR SIZE NW-0- /4 MVR NW-0 /4 (6.35).46 (37.08) NW-6- /4 MVR NW-6 /4 (6.35).46 (37.08) NW-5- /4 MVR NW-5 /4 (6.35).46 (37.08) NW-40- /4 MVR NW-40 /4 (6.35).46 (37.08) NW-50- /4 MVR NW-50 /4 (6.35).46 (37.08) NW-6-3 /8 MVR NW-6 3 /8 (9.53).65 (4.9) NW-5-3 /8 MVR NW-5 3 /8 (9.53).65 (4.9) NW-40-3 /8 MVR NW-40 3 /8 (9.53).65 (4.9) NW-50-3 /8 MVR NW-50 3 /8 (9.53).65 (4.9) NW-6- / MVR NW-6 / (.70).65 (4.9) NW-5- / MVR NW-5 / (.70).65 (4.9) NW-40- / MVR NW-40 / (.70).65 (4.9) NW-50- / MVR NW-50 / (.70).65 (4.9) F Male VR dapters Male VR F SPEIFITIONS Materials s: 304 stainless steel VR Fittings: 36L stainless steel Vacuum range: NW : > x 0-8 mbar - High vacuum F : > x 0-0 mbar - UHV Temperature range: -0º to 00º FLNGE TYPE VR SIZE 33-4 MVR.33 F /4 (6.35).46 (37.08) MVR.33 F 3 /8 (9.53).65 (4.9) 75-4 MVR.75 F /4 (6.35).46 (37.08) MVR.75 F 3 /8 (9.53).65 (4.9) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 80

66 dapter Fittings -to-fitting SETION.8 NW Quick Disconnect dapters FLNGE TYPE ID NW-0- /4 QD NW-0 /4 (6.35) 0.87 (4.75).48 (37.59) NW-6- /4 QD NW-6 /4 (6.35) 0.87 (4.75).48 (37.59) NW-5- /4 QD NW-5 /4 (6.35) 0.87 (4.75).48 (37.59) NW-40- /4 QD NW-40 /4 (6.35) 0.87 (4.75).48 (37.59) NW-0-3 /8 QD NW-0 3 /8 (9.53) 0.8 (7.4).6 (4.5) NW-6-3 /8 QD NW-6 3 /8 (9.53) 0.8 (7.4).6 (4.5) NW-5-3 /8 QD NW-5 3 /8 (9.53) 0.8 (7.4).6 (4.5) NW-40-3 /8 QD NW-40 3/8 (9.53) 0.8 (7.4).6 (4.5) NW-6- / QD NW-6 / (.70) (0.3).79 (45.47) NW-5- / QD NW-5 / (.70) (0.3).79 (45.47) NW-40- / QD NW-40 / (.70) (0.3).79 (45.47) NW-50- / QD NW-50 / (.70) (0.3).79 (45.47) NW-5-3 /4 QD NW-5 3/4 (9.05) 0.65 (5.88).93 (49.0) NW-40-3 /4 QD NW-40 3/4 (9.05) 0.65 (5.88).93 (49.0) NW-50-3 /4 QD NW-50 3/4 (9.05) 0.65 (5.88).93 (49.0) NW-40- QD NW-40 (5.40) (.3).95 (49.53) NW-50- QD NW-50 (5.40) (.3).95 (49.53) ID SPEIFITIONS Materials s: 304 stainless steel QD Fittings: 36L stainless steel Vacuum range: > x 0-8 mbar- High vacuum Temperature range: -0º to 50º Note: On request, NW Quick Disconnects can be provided bored through for the tube. dd -T suffix to the part number and call for price. Example: NW-0-/4 QD-T F Quick Disconnect dapters FLNGE ID 33-4 QD.33 F /4 (6.35) 3 6 (4.76).39 (35.3) QD.33 F 3 /8 (9.53) 9 3 (7.4).53 (38.86) 33- QD.33 F / (.70) 3 3 (0.3).70 (43.8) 75-4 QD.75 F /4 (6.35) 3 6 (4.76).39 (35.3) QD.75 F 3/8 (9.53) 9 3 (7.4).53 (38.86) 75- QD.75 F / (.70) 3 3 (0.3).70 (43.8) QD.75 F 3 /4 (9.05) 5 8 (5.88).99 (50.55) 75- QD.75 F (5.40) 7 8 (.3).0 (5.05) ID Note: On request, F Quick Disconnects can be provided bored through for the tube. dd -T suffix to the part number and call for price. Example: 33-4 QD-T NW Swagelok dapters FLNGE TYPE NW-0- /4 SWG NW-0 /4 (6.35).47 (37.34) NW-6- /4 SWG NW-6 /4 (6.35).47 (37.34) NW-5- /4 SWG NW-5 /4 (6.35).47 (37.34) NW-40- /4 SWG NW-40 /4 (6.35).47 (37.34) NW-50- /4 SWG NW-50 /4 (6.35).47 (37.34) NW-0-3 /8 SWG NW-0 3 /8 (9.53).63 (4.40) NW-6-3 /8 SWG NW-6 3 /8 (9.53).63 (4.40) NW-5-3 /8 SWG NW-5 3 /8 (9.53).63 (4.40) NW-40-3 /8 SWG NW-40 3 /8 (9.53).63 (4.40) NW-50-3 /8 SWG NW-50 3/8 (9.53).63 (4.40) ID ID Swagelok NW Swagelok F F Swagelok dapters FLNGE TYPE 33-4 SWG.33 F /4 (6.35).37 (34.80) SWG.33 F 3 /8 (9.53).58 (40.3) 75-4 SWG.75 F /4 (6.35).37 (34.80) SWG.75 F 3 /8 (9.53).54 (39.) ID ID SPEIFITIONS Materials s: 304 stainless steel Swagelok Fittings: 36L stainless steel Vacuum range: > x 0-6 mbar - High vacuum Temperature range NW : -0º to 00º F : -00º to 450º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 8

67 SETION.9 Flexible Hose & ouplings General Information SPEIFITIONS Nominal ID sizes ellows: 3 /4 to 4 inch ( mm) PV Hose: / to inch ( mm) Flex ouplings: 3 /8 to inch ( mm) Types: NW, ISO, F, S Materials ellows: 36L or 3 stainless steel PV Hose: Wire reinforced polyvinyl chloride s: 304 stainless steel (36L available on request) Vacuum Range Metal seal: > x 0-0 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum PV Hose: > x 0 - Rough vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º PV Hose: -4º to 65º Options: Protective braided sleeving ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Spring rates are called out in pounds/inch Flexible Vacuum onnections Flexible vacuum connections are typically made by using edge welded bellows, hydroformed flexible couplings and hose or PV hose. Edge welded bellows provide the greatest stroke and flexibility, but are the most susceptible to damage. Edge welded bellows are also more expensive than the other flexible connections. Nor-al Products offers flexible couplings and flexible hose as standards. Edge welded bellows assemblies can be provided in a variety of materials as specials. PV hose offers a low cost alternative to stainless steel flexible hose. Flexible Hose Flexible stainless steel hose is available in 3 /4 to 4 inch ( mm) diameters in standard lengths of, 8, 4 and 36 inches (304.8, 457., and 94.4mm) with NW, ISO, F and S flanges. Hose with NW and ISO flanges are also available In 0, 0 and 40 Inch (metric equivalent) lengths. F and S flanged hose has one rotatable and one nonrotatable flange for ease of bolt hole alignment. S flanged hose may require an O-ring groove on one flange for proper installation. e sure to specify. NW to F adapter hose provides a flexible transition between components with NW and F flanges. NW hose is available in medium wall FH- (0.00 Inch (.54mm) wall thickness), heavy wall TH- (0.07 Inches (.43mm)), Minimum Static end Radius (permanently bent) and thin wall LH- (0.006 Inches (.5mm)). Thin wall hose is the perfect choice for applications requiring increased flexibility. Protective braiding is offered as a standard for NW and F medium wall tubing FH- in diameters up to and including 4 inches (0.6mm). Flexible ouplings Pressurizing the inside of thin wall stainless steel tubing inside a mold forms convolutions in flexible couplings and hose. Generally speaking, when comparing flexible couplings to hose, couplings are thinner walled, and have more convolutions per inch, resulting in greater flexibility and stroke, and are used for alignment or vibration isolation rather than as roughing lines. eing thinner, flexible couplings are more susceptible to mechanical damage than hose. Nor-al Products flexible couplings have more convolutions than comparable products, resulting in greater flexibility and lower spring rates. Maximum compression for flexible couplings is typically 0% of the convolution (flexible) length. Extension is typically 0%. ouplings are available in 3 or 36L stainless steel in various lengths with NW, ISO, F and S flanges. PV Hose Plasticized PV hose can be used as a low cost rough vacuum line. n embedded spiral wire prevents the wall from collapsing under vacuum. Unlike edge welded bellows, flexible couplings and hose, which are UHV compatible, PV hose should be used for rough vacuum due to the higher outgassing rate. lthough it can be bent relatively easily, it cannot be compressed or extended. Order by the foot with or without NW flanges. Each length includes two hose clamps for installation. end radii are listed for each wall thickness and diameter, while the hose is under vacuum. 8

68 Flexible Hose & ouplings Flexible ouplings SETION.9 NW Flexible ouplings FLNGE TYPE ELLOWS ID WLL THIKNESS FREE LENGTH SPRING RTE OMPRESSED LENGTH F-NW-0- NW-0 3 /8 (9.55) (.5) 3.0 (8.8) (76.0) F-NW-0- NW-0 3 /8 (9.55) (.5) 4.0 (06.68) (96.5) F-NW-0-3 NW-0 3 /8 (9.55) (.5) 5.0 (3.08) 4.6 (6.84) F-NW-6- NW-6 / (.70) (.5) 3.0 (8.8) (76.0) F-NW-6- NW-6 / (.70) (.5) 4.0 (06.68) (96.5) F-NW-6-3 NW-6 / (.70) (.5) 5.0 (3.08) (6.84) F-NW-5- NW-5 3 /4 (9.05) (.5) 3.0 (8.8) (76.0) F-NW-5- NW-5 3 /4 (9.05) (.5) 4.0 (06.68) (96.5) F-NW-5-3 NW-5 3 /4 (9.05) (.5) 5.0 (3.08) (6.84) F-NW-40- NW-40 / (38.0) (.5) 3.0 (8.8) (76.0) F-NW-40- NW-40 / (38.0) (.5) 4.0 (06.68) (96.5) F-NW-40-3 NW-40 / (38.0) (.5) 5.0 (3.08) (6.84) F-NW-40-6 NW-40 / (38.0) (.5) 8.0 (08.8) (77.80) F-NW-50- NW-50 3 /4 (44.45) (.5) 3.0 (8.8) (76.0) F-NW-50- NW-50 3 /4 (44.45) (.5) 4.0 (06.68) (96.5) F-NW-50-3 NW-50 3 /4 (44.45) (.5) 5.0 (3.08) (6.84) Free Length Rotatable Nonrotatable Free Length Free Length ISO Flexible ouplings FLNGE TYPE ELLOWS ID WLL THIKNESS FREE LENGTH SPRING RTE OMPRESSED LENGTH F-ISO-50-4 ISO-63 / (63.50) (.0) 7.00 (77.80) (57.48) F-ISO ISO-80 3 (76.0) (.0) 7.00 (77.80) (57.48) F-ISO ISO-00 4 (0.60) 0.00 (.5) 7.00 (77.80) (57.48) F-ISO ISO-60 6 (5.40) 0.00 (.5) 7.00 (77.80) (57.48) F-ISO ISO-00 8 (03.0) 0.00 (.5) 7.00 (77.80) (57.48) F-ISO ISO-50 0 (54.00) 0.0 (.30) 3.50 (34.90) (89.56) S Flexible ouplings FLNGE TYPE ELLOWS ID WLL THIKNESS FREE LENGTH SPRING RTE OMPRESSED LENGTH F-S-5-00N-3 S 5 (50.80) (.5) 6.00 (5.40) (37.6) F-S-5-50N-4 S 5 / (63.50) (.0) 7.00 (77.80) (57.48) F-S-6-300N-4 S 6 3 (76.0) (.0) 7.00 (77.80) (57.48) F-S N-4 S (0.60) (.0) 7.00 (77.80) (57.48) F-S-9-400N-4 S 9 4 (0.60) (.0) 7.00 (77.80) (57.48) F-S-9-600N-4 S 9 6 (5.40) 0.00 (.5) 7.00 (77.80) (57.48) F-S--600N-4 S 6 (5.40) 0.00 (.5) 7.00 (77.80) (57.48) F-S--800N-4 S 8 (03.0) 0.00 (.5) 7.00 (77.80) (57.48) F-S N-4 S (03.0) 0.00 (.5) 7.00 (77.80) (57.48) F-S N-0 S (54.00) 0.0 (.30) 4.00 (355.60) 87.0 (304.80) F-S-6-000N-0 S 6 0 (54.00) 0.0 (.30) 4.00 (355.60) 87.0 (304.80) F-S-6-00N-.8 S 6 (304.8) 0.0 (.30) 5.87 (403.0) (350.5) Note: all for S O-ring groove pricing F Flexible ouplings FLNGE TYPE ELLOWS ID WLL THIKNESS FREE LENGTH SPRING RTE OMPRESSED LENGTH F F / (.70) (.5) 3.0 (8.8) (76.0) F F / (.70) (.5) 4.0 (06.68) (96.5) F F / (.70) (.5) 5.0 (3.08) (6.84) F-00-. F 3/4 (9.05) (.5) 3.0 (8.8) (76.0) F-00-. F 3 /4 (9.05) (.5) 4.0 (06.68) (96.5) F F 3 /4 (9.05) (.5) 5.0 (3.08) (6.84) F F / (38.0) (.5) 3.0 (8.8) (76.0) F F / (38.0) (.5) 4.0 (06.68) (96.5) F F / (38.0) (.5) 5.0 (3.08) (6.84) F F / (38.0) (.5) 8.0 (08.8) (77.80) F F (50.80) (.5) 6.00 (5.40) (37.6) F F / (63.50) (.0) 7.00 (77.80) (57.48) F F 3 (76.0) (.0) 7.00 (77.80) (57.48) F F 4 (0.60) (.0) 7.00 (77.80) (57.48) F F 5 (7.00) (.0) 7.00 (77.80) (57.48) F F 6 (5.40) 0.00 (.5) 7.00 (77.80) (57.48) F F 8 (03.0) 0.00 (.5) 7.00 (77.80) (57.48) Free Length SPEIFITIONS Nominal ID sizes: 3 /8 to inches ( mm) Materials ellows: 36L or 3 stainless steel s: 304 stainless steel (36L available on request) Vacuum Range Metal seal: > x 0-0 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 83

69 SETION.9 Flexible Hose & ouplings Flexible Stainless Steel Hose SPEIFITIONS Nominal ID sizes: 3 /4 to 4 inch ( mm) Materials ellows: 3 stainless steel Tube ends: 304 stainless steel Vacuum Range: > x 0-0 mbar - UHV Temperature Range: -00º to 450º Options: Protective braided sleeving Length Flexible Stainless Steel Hose without s NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS FH-075-3/4 (9.05). (8.9) (304.80) (.0).6 (3.00) FH /4 (9.05). (8.9) 8 (457.0) (.0).6 (3.00) FH /4 (9.05). (8.9) 4 (609.60) (.0).6 (3.00) FH /4 (9.05). (8.9) 36 (94.40) (.0).6 (3.00) FH-00- (5.40).37 (34.80) (304.80) (.0).46 (37.08) FH-00-8 (5.40).37 (34.80) 8 (457.0) (.0).46 (37.08) FH-00-4 (5.40).37 (34.80) 4 (609.60) (.0).46 (37.08) FH (5.40).37 (34.80) 36 (94.40) (.0).46 (37.08) FH-50- / (38.0).06 (5.3) (304.80) 0.00 (.5).6 (54.86) FH-50-8 / (38.0).06 (5.3) 8 (457.0) 0.00 (.5).6 (54.86) FH-50-4 / (38.0).06 (5.3) 4 (609.60) 0.00 (.5).6 (54.86) FH / (38.0).06 (5.3) 36 (94.40) 0.00 (.5).6 (54.86) FH-00- (50.80).55 (64.77) (304.80) 0.0 (.30) 3.50 (88.90) FH-00-8 (50.80).55 (64.77) 8 (457.0) 0.0 (.30) 3.50 (88.90) FH-00-4 (50.80).55 (64.77) 4 (609.60) 0.0 (.30) 3.50 (88.90) FH (50.80).55 (64.77) 36 (94.40) 0.0 (.30) 3.50 (88.90) FH-50- / (63.50) 3.34 (84.84) (304.80) 0.06 (.4) 4.5 (07.95) FH-50-8 / (63.50) 3.34 (84.84) 8 (457.0) 0.06 (.4) 4.5 (07.95) FH-50-4 / (63.50) 3.34 (84.84) 4 (609.60) 0.06 (.4) 4.5 (07.95) FH / (63.50) 3.34 (84.84) 36 (94.40) 0.06 (.4) 4.5 (07.95) FH (76.0) 3.99 (0.35) (304.80) 0.06 (.4) 6.00 (5.40) FH (76.0) 3.99 (0.35) 8 (457.0) 0.06 (.4) 6.00 (5.40) FH (76.0) 3.99 (0.35) 4 (609.60) 0.06 (.4) 6.00 (5.40) FH (76.0) 3.99 (0.35) 36 (94.40) 0.06 (.4) 6.00 (5.40) FH (0.60) 4.83 (.68) (304.80) 0.06 (.4) 8.60 (8.44) FH (0.60) 4.83 (.68) 8 (457.0) 0.06 (.4) 8.60 (8.44) FH (0.60) 4.83 (.68) 4 (609.60) 0.06 (.4) 8.60 (8.44) FH (0.60) 4.83 (.68) 36 (94.40) 0.06 (.4) 8.60 (8.44) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 84

70 Flexible Hose & ouplings Flexible Stainless Steel Hose SETION.9 NW Flexible Stainless Steel Hose Thin Wall FLNGE TYPE NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS LH NW NW-6 3 /4 (9.05).0 (5.9) 0 (54.00) (.5) 3.0 (76.0) LH-075--NW NW-6 3 /4 (9.05).0 (5.9) (304.80) (.5) 3.0 (76.0) LH NW NW-6 3 /4 (9.05).0 (5.9) 8 (457.0) (.5) 3.0 (76.0) LH NW NW-6 3 /4 (9.05).0 (5.9) 4 (609.60) (.5) 3.0 (76.0) LH NW NW-6 3 /4 (9.05).0 (5.9) 36 (94.40) (.5) 3.0 (76.0) LH-00-0-NW NW-5 (5.40).37 (34.80) 0 (54.00) (.5) 4.0 (0.60) LH-00--NW NW-5 (5.40).37 (34.80) (304.80) (.5) 4.0 (0.60) LH-00-8-NW NW-5 (5.40).37 (34.80) 8 (457.0) (.5) 4.0 (0.60) LH-00-4-NW NW-5 (5.40).37 (34.80) 4 (609.60) (.5) 4.0 (0.60) LH NW NW-5 (5.40).37 (34.80) 36 (94.40) (.5) 4.0 (0.60) LH-50-0-NW NW-40 / (38.0).9 (48.5) 0 (54.00) (.5) 6.0 (5.40) LH-50--NW NW-40 / (38.0).9 (48.5) (304.80) (.5) 6.0 (5.40) LH-50-8-NW NW-40 / (38.0).9 (48.5) 8 (457.0) (.5) 6.0 (5.40) LH-50-4-NW NW-40 / (38.0).9 (48.5) 4 (609.60) (.5) 6.0 (5.40) LH NW NW-40 / (38.0).9 (48.5) 36 (94.40) (.5) 6.0 (5.40) LH-00-0-NW NW-50 (50.80).45 (6.3) 0 (54.00) (.5) 7.5 (90.50) LH-00--NW NW-50 (50.80).45 (6.3) (304.80) (.5) 7.5 (90.50) LH-00-8-NW NW-50 (50.80).45 (6.3) 8 (457.0) (.5) 7.5 (90.50) LH-00-4-NW NW-50 (50.80).45 (6.3) 4 (609.60) (.5) 7.5 (90.50) LH NW NW-50 (50.80).45 (6.3) 36 (94.40) (.5) 7.5 (90.50) SPEIFITIONS Nominal ID sizes: 3 /4 to inch ( mm) Materials Hose: 3 stainless steel Tube ends: 304 stainless steel s: 304 stainless steel (36L available on request) Vacuum Range Metal seal: > x 0-0 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Options: Protective braided sleeving NW Flexible Stainless Steel Hose Medium Wall FLNGE TYPE NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS FH NW NW-6 3 /4 (9.05). (8.9) 0 (54.00) (.0).6 (3.00) FH-075--NW NW-6 3/4 (9.05). (8.9) (304.80) (.0).6 (3.00) FH NW NW-6 3/4 (9.05). (8.9) 8 (457.0) (.0).6 (3.00) FH NW NW-6 3 /4 (9.05). (8.9) 0 (508.00) (.0).6 (3.00) FH NW NW-6 3 /4 (9.05). (8.9) 4 (609.60) (.0).6 (3.00) FH NW NW-6 3 /4 (9.05). (8.9) 36 (94.40) (.0).6 (3.00) FH NW NW-6 3 /4 (9.05). (8.9) 40 (06.00) (.0).6 (3.00) FH-00-0-NW NW-5 (5.40).37 (34.80) 0 (54.00) (.0).46 (37.08) FH-00--NW NW-5 (5.40).37 (34.80) (304.80) (.0).46 (37.08) FH-00-8-NW NW-5 (5.40).37 (34.80) 8 (457.0) (.0).46 (37.08) FH-00-0-NW NW-5 (5.40).37 (34.80) 0 (508.00) (.0).46 (37.08) FH-00-4-NW NW-5 (5.40).37 (34.80) 4 (609.60) (.0).46 (37.08) FH NW NW-5 (5.40).37 (34.80) 36 (94.40) (.0).46 (37.08) FH NW NW-5 (5.40).37 (34.80) 40 (06.00) (.0).46 (37.08) FH-50-0-NW NW-40 / (38.0).06 (5.3) 0 (54.00) 0.00 (.5).6 (54.86) FH-50--NW NW-40 / (38.0).06 (5.3) (304.80) 0.00 (.5).6 (54.86) FH-50-8-NW NW-40 / (38.0).06 (5.3) 8 (457.0) 0.00 (.5).6 (54.86) FH-50-0-NW NW-40 / (38.0).06 (5.3) 0 (508.00) 0.00 (.5).6 (54.86) FH-50-4-NW NW-40 / (38.0).06 (5.3) 4 (609.60) 0.00 (.5).6 (54.86) FH NW NW-40 / (38.0).06 (5.3) 36 (94.40) 0.00 (.5).6 (54.86) FH NW NW-40 / (38.0).06 (5.3) 40 (06.00) 0.00 (.5).6 (54.86) FH-00-0-NW NW-50 (50.80).55 (64.77) 0 (54.00) 0.0 (.30) 3.50 (88.90) FH-00--NW NW-50 (50.80).55 (64.77) (304.80) 0.0 (.30) 3.50 (88.90) FH-00-8-NW NW-50 (50.80).55 (64.77) 8 (457.0) 0.0 (.30) 3.50 (88.90) FH-00-0-NW NW-50 (50.80).55 (64.77) 0 (508.00) 0.0 (.30) 3.50 (88.90) FH-00-4-NW NW-50 (50.80).55 (64.77) 4 (609.60) 0.0 (.30) 3.50 (88.90) FH NW NW-50 (50.80).55 (64.77) 36 (94.40) 0.0 (.30) 3.50 (88.90) FH NW NW-50 (50.80).55 (64.77) 40 (06.00) 0.0 (.30) 3.50 (88.90) Length Larger hose IDs and other flange configurations available upon request. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 85

71 SETION.9 Flexible Hose & ouplings Flexible Stainless Steel Hose Length NW Flexible Stainless Steel Hose Thick Wall FLNGE TYPE NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS TH NW NW-6 3 /4 (9.05).0 (7.94) 0 (54.00) 0.07 (.43).3 (54.0) TH NW NW-6 3 /4 (9.05).0 (7.94) 0 (508.00) 0.07 (.43).3 (54.0) TH NW NW-6 3 /4 (9.05).0 (7.94) 40 (06.00) 0.07 (.43).3 (54.0) TH-00-0-NW NW-5 (5.40).50 (38.0) 0 (54.00) 0.07 (.43).88 (73.5) TH-00-0-NW NW-5 (5.40).50 (38.0) 0 (508.00) 0.07 (.43).88 (73.5) TH NW NW-5 (5.40).50 (38.0) 40 (06.00) 0.07 (.43).88 (73.5) TH-50-0-NW NW-40 / (38.0).0 (53.34) 0 (54.00) 0.00 (.5) 3.50 (88.90) TH-50-0-NW NW-40 / (38.0).0 (53.34) 0 (508.00) 0.00 (.5) 3.50 (88.90) TH NW NW-40 / (38.0).0 (53.34) 40 (06.00) 0.00 (.5) 3.50 (88.90) TH-00-0-NW NW-50 (50.80).63 (66.80) 0 (54.00) 0.00 (.5) 5.5 (33.35) TH-00-0-NW NW-50 (50.80).63 (66.80) 0 (508.00) 0.00 (.5) 5.5 (33.35) TH NW NW-50 (50.80).63 (66.80) 40 (06.00) 0.00 (.5) 5.5 (33.35) F NW Nonrotatable Length NW/F Flexible Stainless Steel dapter Hose Medium Wall FLNGE TYPE FLNGE TYPE NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS FH-075--NW-F NW-6 F /4 (9.05). (8.9) (304.80) (.0).6 (3.00) FH NW-F NW-6 F-.33 3/4 (9.05). (8.9) 8 (457.0) (.0).6 (3.00) FH NW-F NW-6 F-.33 3/4 (9.05). (8.9) 4 (609.60) (.0).6 (3.00) FH NW-F NW-6 F /4 (9.05). (8.9) 36 (94.40) (.0).6 (3.00) FH-50--NW-F NW-40 F-.75 / (38.0).06 (5.3) (304.80) 0.00 (.5).6 (54.86) FH-50-8-NW-F NW-40 F-.75 / (38.0).06 (5.3) 8 (457.0) 0.00 (.5).6 (54.86) FH-50-4-NW-F NW-40 F-.75 / (38.0).06 (5.3) 4 (609.60) 0.00 (.5).6 (54.86) FH NW-F NW-40 F-.75 / (38.0).06 (5.3) 36 (94.40) 0.00 (.5).6 (54.86) SPEIFITIONS Nominal ID sizes: 3 /4 to 4 inch ( mm) Materials Hose: 3 stainless steel Tube ends: 304 stainless steel s: 304 stainless steel (36L available on request) Vacuum Range Metal seal: > x 0-0 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Options: Protective braided sleeving Length ISO Flexible Stainless Steel Hose Medium Wall ISO Flexible Stainless Steel Hose Thick Wall FLNGE TYPE FLNGE TYPE NOMINL ID NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS TH-50-0-ISO ISO-63 / (63.50) 3.0 (78.74) 0 (508.00) 0.00 (.5) 8.00 (03.0) TH ISO ISO-63 / (63.50) 3.0 (78.74) 40 (06.00) 0.00 (.5) 8.00 (03.0) TH ISO ISO-80 3 (76.0) 3.9 (99.57) 0 (508.00) 0.00 (.5) 9.00 (8.60) TH ISO ISO-80 3 (76.0) 3.9 (99.57) 40 (06.00) 0.00 (.5) 9.00 (8.60) TH ISO ISO-00 4 (0.60) 4.8 (.43) 0 (508.00) 0.00 (.5) 3.00 (330.0) TH ISO ISO-00 4 (0.60) 4.8 (.43) 40 (06.00) 0.00 (.5) 3.00 (330.0) HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS FH-50-0-ISO ISO-63 / (63.50) 3.34 (84.84) 0 (54.00) 0.06 (.4) 3.5 (80.0) FH-50--ISO ISO-63 / (63.50) 3.34 (84.84) (304.80) 0.06 (.4) 3.5 (80.0) FH-50-8-ISO ISO-63 / (63.50) 3.34 (84.84) 8 (457.0) 0.06 (.4) 3.5 (80.0) FH-50-0-ISO ISO-63 / (63.50) 3.34 (84.84) 0 (508.00) 0.06 (.4) 3.5 (80.0) FH-50-4-ISO ISO-63 / (63.50) 3.34 (84.84) 4 (609.60) 0.06 (.4) 3.5 (80.0) FH ISO ISO-63 / (63.50) 3.34 (84.84) 36 (94.40) 0.06 (.4) 3.5 (80.0) FH ISO ISO-63 3 (76.0) 3.99 (0.35) 40 (06.00) 0.06 (.4) 3.5 (80.0) FH ISO ISO-80 3 (76.0) 3.99 (0.35) 0 (54.00) 0.06 (.4) 3.8 (97.03) FH-300--ISO ISO-80 3 (76.0) 3.99 (0.35) (304.80) 0.06 (.4) 3.8 (97.03) FH ISO ISO-80 3 (76.0) 3.99 (0.35) 8 (457.0) 0.06 (.4) 3.8 (97.03) FH ISO ISO-80 3 (76.0) 3.99 (0.35) 0 (508.00) 0.06 (.4) 3.8 (97.03) FH ISO ISO-80 3 (76.0) 3.99 (0.35) 4 (609.60) 0.06 (.4) 3.8 (97.03) FH ISO ISO-80 3 (76.0) 3.99 (0.35) 36 (94.40) 0.06 (.4) 3.8 (97.03) FH ISO ISO-80 4 (0.60) 4.83 (.68) 40 (06.00) 0.06 (.4) 3.8 (97.03) FH lSO ISO-00 4 (0.60) 4.83 (.68) 0 (54.00) 0.06 (.4) 4.45 (3.03) FH-400--lSO ISO-00 4 (0.60) 4.83 (.68) (304.80) 0.06 (.4) 4.45 (3.03) FH ISO ISO-00 4 (0.60) 4.83 (.68) 8 (457.0) 0.06 (.4) 4.45 (3.03) FH ISO ISO-00 4 (0.60) 4.83 (.68) 0 (508.00) 0.06 (.4) 4.45 (3.03) FH ISO ISO-00 4 (0.60) 4.83 (.68) 4 (609.60) 0.06 (.4) 4.45 (3.03) FH ISO ISO-00 4 (0.60) 4.83 (.68) 36 (94.40) 0.06 (.4) 4.45 (3.03) FH ISO ISO-00 4 (0.60) 4.83 (.68) 40 (06.00) 0.06 (.4) 4.45 (3.03) 86

72 Flexible Hose & ouplings Flexible Stainless Steel Hose SETION.9 F Flexible Stainless Steel Hose NOMINL ID HOSE OVERLL LENGTH FLNGE WLL THIKNESS STTI END RDIUS FH-075--F 3 4 (9.05). (8.9) (304.80).33 (33.78) (.0).6 (3.00) FH F 3 4 (9.05). (8.9) 8 (547.0).33 (33.78) (.0).6 (3.00) FH F 3 4 (9.05). (8.9) 4 (609.60).33 (33.78) (.0).6 (3.00) FH F 3 4 (9.05). (8.9) 36 (94.40).33 (33.78) (.0).6 (3.00) FH-00--F (5.40).37 (34.80) (304.80). (53.85) (.0).46 (37.08) FH-00-8-F (5.40).37 (34.80) 8 (547.0). (53.85) (.0).46 (37.08) FH-00-4-F (5.40).37 (34.80) 4 (609.60). (53.85) (.0).46 (37.08) FH F (5.40).37 (34.80) 36 (94.40). (53.85) (.0).46 (37.08) FH-50--F (38.0).06 (5.3) (304.80).75 (69.85) 0.00 (.5).6 (54.86) FH-50-8-F (38.0).06 (5.3) 8 (547.0).75 (69.85) 0.00 (.5).6 (54.86) FH-50-4-F (38.0).06 (5.3) 4 (609.60).75 (69.85) 0.00 (.5).6 (54.86) FH F (38.0).06 (5.3) 36 (94.40).75 (69.85) 0.00 (.5).6 (54.86) FH-00--F (50.80).55 (64.77) (304.80) 3.38 (85.85) 0.0 (.30) 3.50 (88.90) FH-00-8-F (50.80).55 (64.77) 8 (547.0) 3.38 (85.85) 0.0 (.30) 3.50 (88.90) FH-00-4-F (50.80).55 (64.77) 4 (609.60) 3.38 (85.85) 0.0 (.30) 3.50 (88.90) FH F (50.80).55 (64.77) 36 (94.40) 3.38 (85.85) 0.0 (.30) 3.50 (88.90) FH-50--F (63.50) 3.34 (84.84) (304.80) 4.50 (4.30) 0.06 (.4) 4.5 (07.95) FH-50-8-F (63.50) 3.34 (84.84) 8 (547.0) 4.50 (4.30) 0.06 (.4) 4.5 (07.95) FH-50-4-F (63.50) 3.34 (84.84) 4 (609.60) 4.50 (4.30) 0.06 (.4) 4.5 (07.95) FH F (63.50) 3.34 (84.84) 36 (94.40) 4.50 (4.30) 0.06 (.4) 4.5 (07.95) FH-300--F 3 (76.0) 3.99 (0.35) (304.80) 4.6 (7.35) 0.06 (.4) 6.00 (5.40) FH F 3 (76.0) 3.99 (0.35) 8 (547.0) 4.6 (7.35) 0.06 (.4) 6.00 (5.40) FH F 3 (76.0) 3.99 (0.35) 4 (609.60) 4.6 (7.35) 0.06 (.4) 6.00 (5.40) FH F 3 (76.0) 3.99 (0.35) 36 (94.40) 4.6 (7.35) 0.06 (.4) 6.00 (5.40) FH-400--F 4 (0.60) 4.83 (.68) (304.80) 6.00 (5.40) 0.06 (.4) 8.60 (8.44) FH F 4 (0.60) 4.83 (.68) 8 (547.0) 6.00 (5.40) 0.06 (.4) 8.60 (8.44) FH F 4 (0.60) 4.83 (.68) 4 (609.60) 6.00 (5.40) 0.06 (.4) 8.60 (8.44) FH F 4 (0.60) 4.83 (.68) 36 (94.40) 6.00 (5.40) 0.06 (.4) 8.60 (8.44) Note: See raided Hose selection next page. S Flexible Stainless Steel Hose DESRIPTION NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS FH-50--S S-5 on one port / (63.50) 3.34 (84.84) (304.80) 0.06 (.4) 4.5 (07.95) FH-50--S S-5 on both ports / (63.50) 3.34 (84.84) (304.80) 0.06 (.4) 4.5 (07.95) FH-50-8-S S-5 on one port / (63.50) 3.34 (84.84) 8 (457.0) 0.06 (.4) 4.5 (07.95) FH-50-8-S S-5 on both ports / (63.50) 3.34 (84.84) 8 (457.0) 0.06 (.4) 4.5 (07.95) FH-50-4-S S-5 on one port / (63.50) 3.34 (84.84) 4 (609.60) 0.06 (.4) 4.5 (07.95) FH-50-4-S S-5 on both ports / (63.50) 3.34 (84.84) 4 (609.60) 0.06 (.4) 4.5 (07.95) FH S S-5 on one port / (63.50) 3.34 (84.84) 36 (94.40) 0.06 (.4) 4.5 (07.95) FH S S-5 on both ports / (63.50) 3.34 (84.84) 36 (94.40) 0.06 (.4) 4.5 (07.95) FH-300--S S-6 on one port 3 (76.0) 3.99 (0.35) (304.80) 0.06 (.4) 6.00 (5.40) FH-300--S S-6 on both ports 3 (76.0) 3.99 (0.35) (304.80) 0.06 (.4) 6.00 (5.40) FH S S-6 on one port 3 (76.0) 3.99 (0.35) 8 (457.0) 0.06 (.4) 6.00 (5.40) FH S S-6 on both ports 3 (76.0) 3.99 (0.35) 8 (457.0) 0.06 (.4) 6.00 (5.40) FH S S-6 on one port 3 (76.0) 3.99 (0.35) 4 (609.60) 0.06 (.4) 6.00 (5.40) FH S S-6 on both ports 3 (76.0) 3.99 (0.35) 4 (609.60) 0.06 (.4) 6.00 (5.40) FH S S-6 on one port 3 (76.0) 3.99 (0.35) 36 (94.40) 0.06 (.4) 6.00 (5.40) FH S S-6 on both ports 3 (76.0) 3.99 (0.35) 36 (94.40) 0.06 (.4) 6.00 (5.40) FH-400--S S-7.5 on one port 4 (0.60) 4.83 (.68) (304.80) 0.06 (.4) 8.60 (8.44) FH-400--S S-7.5 on both ports 4 (0.60) 4.83 (.68) (304.80) 0.06 (.4) 8.60 (8.44) FH S S-7.5 on one port 4 (0.60) 4.83 (.68) 8 (457.0) 0.06 (.4) 8.60 (8.44) FH S S-7.5 on both ports 4 (0.60) 4.83 (.68) 8 (457.0) 0.06 (.4) 8.60 (8.44) FH S S-7.5 on one port 4 (0.60) 4.83 (.68) 4 (609.60) 0.06 (.4) 8.60 (8.44) FH S S-7.5 on both ports 4 (0.60) 4.83 (.68) 4 (609.60) 0.06 (.4) 8.60 (8.44) FH S S-7.5 on one port 4 (0.60) 4.83 (.68) 36 (94.40) 0.06 (.4) 8.60 (8.44) FH S S-7.5 on both ports 4 (0.60) 4.83 (.68) 36 (94.40) 0.06 (.4) 8.60 (8.44) Note: all for O-ring groove pricing if required Length Length ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 87

73 SETION.9 Flexible Hose & ouplings raided Stainless Steel Flexible Hose Length NW Flexible Stainless Steel raided Hose FLNGE TYPE NOMINL ID HOSE OVERLL LENGTH WLL THIKNESS STTI END RDIUS FH-075--NW NW-6 3 /4 (9.05) /4 (3.75) (304.80) (.0).09 (53.09) FH NW NW-6 3 /4 (9.05) /4 (3.75) 8 (457.0) (.0).09 (53.09) FH NW NW-6 3/4 (9.05) /4 (3.75) 0 (508.00) (.0).09 (53.09) FH NW NW-6 3/4 (9.05) /4 (3.75) 4 (609.60) (.0).09 (53.09) FH NW NW-6 3 /4 (9.05) /4 (3.75) 36 (94.40) (.0).09 (53.09) FH NW NW-6 3 /4 (9.05) /4 (3.75) 40 (06.00) (.0).09 (53.09) FH-00--NW NW-5 (5.40) 5 /8 (4.8) (304.80) (.0).5 (64.0) FH-00-8-NW NW-5 (5.40) 5 /8 (4.8) 8 (457.0) (.0).5 (64.0) FH-00-0-NW NW-5 (5.40) 5 /8 (4.8) 0 (508.00) (.0).5 (64.0) FH-00-4-NW NW-5 (5.40) 5 /8 (4.8) 4 (609.60) (.0).5 (64.0) FH NW NW-5 (5.40) 5 /8 (4.8) 36 (94.40) (.0).5 (64.0) FH NW NW-5 (5.40) 5 /8 (4.8) 40 (06.00) (.0).5 (64.0) FH-50--NW NW-40 / (38.0) /4 (57.5) (304.80) 0.00 (.5) 3.86 (98.04) FH-50-8-NW NW-40 / (38.0) /4 (57.5) 8 (457.0) 0.00 (.5) 3.86 (98.04) FH-50-0-NW NW-40 / (38.0) /4 (57.5) 0 (508.00) 0.00 (.5) 3.86 (98.04) FH-50-4-NW NW-40 / (38.0) /4 (57.5) 4 (609.60) 0.00 (.5) 3.86 (98.04) FH NW NW-40 / (38.0) /4 (57.5) 36 (94.40) 0.00 (.5) 3.86 (98.04) FH NW NW-40 / (38.0) /4 (57.5) 40 (06.00) 0.00 (.5) 3.86 (98.04) FH-00--NW NW-50 (50.80) 3 /4 (69.85) (304.80) 0.0 (.30) 4.7 (9.89) FH-00-8-NW NW-50 (50.80) 3 /4 (69.85) 8 (457.0) 0.0 (.30) 4.7 (9.89) FH-00-0-NW NW-50 (50.80) 3 /4 (69.85) 0 (508.00) 0.0 (.30) 4.7 (9.89) FH-00-4-NW NW-50 (50.80) 3 /4 (69.85) 4 (609.60) 0.0 (.30) 4.7 (9.89) FH NW NW-50 (50.80) 3 /4 (69.85) 36 (94.40) 0.0 (.30) 4.7 (9.89) FH NW NW-50 (50.80) 3 /4 (69.85) 40 (06.00) 0.0 (.30) 4.7 (9.89) Length F Flexible Stainless Steel raided Hose NOMINL ID HOSE OVERLL LENGTH FLNGE WLL THIKNESS STTI END RDIUS FH-075--F 3 /4 (9.05) /4 (3.75) (304.80).33 (33.78) (.0).09 (53.09) FH F 3 /4 (9.05) /4 (3.75) 8 (457.0).33 (33.78) (.0).09 (53.09) FH F 3 /4 (9.05) /4 (3.75) 4 (609.60).33 (33.78) (.0).09 (53.09) FH F 3 /4 (9.05) /4 (3.75) 36 (94.40).33 (33.78) (.0).09 (53.09) FH-00--F (5.40) 5 /8 (4.8) (304.80). (53.85) (.0).5 (64.0) FH-00-8-F (5.40) 5 /8 (4.8) 8 (457.0). (53.85) (.0).5 (64.0) FH-00-4-F (5.40) 5 /8 (4.8) 4 (609.60). (53.85) (.0).5 (64.0) FH F (5.40) 5 /8 (4.8) 36 (94.40). (53.85) (.0).5 (64.0) FH-50--F / (38.0) /4 (57.5) (304.80).75 (69.85) 0.00 (.5) 3.86 (98.04) FH-50-8-F / (38.0) /4 (57.5) 8 (457.0).75 (69.85) 0.00 (.5) 3.86 (98.04) FH-50-4-F / (38.0) /4 (57.5) 4 (609.60).75 (69.85) 0.00 (.5) 3.86 (98.04) FH F / (38.0) /4 (57.5) 36 (94.40).75 (69.85) 0.00 (.5) 3.86 (98.04) FH-00--F (50.80) 3 /4 (69.85) (304.80) 3.38 (85.85) 0.0 (.30) 4.7 (9.89) FH-00-8-F (50.80) 3 /4 (69.85) 8 (457.0) 3.38 (85.85) 0.0 (.30) 4.7 (9.89) FH-00-4-F (50.80) 3 /4 (69.85) 4 (609.60) 3.38 (85.85) 0.0 (.30) 4.7 (9.89) FH F (50.80) 3 /4 (69.85) 36 (94.40) 3.38 (85.85) 0.0 (.30) 4.7 (9.89) SPEIFITIONS Nominal ID sizes: 3 /4 to inch ( mm) Materials ellows: 3 stainless steel Tube ends: 304 stainless steel s: 304 stainless steel (36L available on request) Vacuum Range Metal seal: > x 0-0 mbar - UHV Elastomer seal: > x 0-8 mbar - High vacuum Temperature Range Metal seal: -00º to 450º Elastomer seal: -0º to 50º Larger hose IDs and other flange configurations available upon request. 88

74 Flexible Hose & ouplings PV Flexible Hose SETION.9 PV Flexible Hose Each length includes two hose clamps for installation. NOMINL ID HOSE STTI END RDIUS PV-050 / (.70) 0.83 (0.65).00 (50.80) PV /4 (9.05).5 (8.58) 3.00 (76.0) PV-00 (5.40).375 (34.93) 4.00 (0.60) PV-50 / (38.0).000 (50.80) 6.00 (5.40) PV-00 (50.80).500 (63.50) 8.00 (03.0) Note: To order specify length required in feet as follows: PV and PV ID Length.500 NW PV Hose Nipples FLNGE TYPE NIPPLE MTERIL HN-NW NW SS 0.50 (.70).6 (3.00) HN-NW NW SS 0.75 (9.05).6 (3.00) HN-NW-5-00 NW SS.00 (5.40).50 (38.0) HN-NW NW SS.50 (38.0).97 (50.04) HN-NW NW SS.00 (50.80).7 (55.) PV Hose with NW s FLNGE TYPE NOMINL ID HOSE OVERLL LENGTH STTI END RDIUS PV-050--NW NW-0 / (.70) 0.83 (0.65) (304.80).00 (50.80) PV NW NW-0 / (.70) 0.83 (0.65) 4 (609.60).00 (50.80) PV NW NW-0 / (.70) 0.83 (0.65) 36 (94.40).00 (50.80) PV NW NW-0 / (.70) 0.83 (0.65) 7 (88.80).00 (50.80) PV-075--NW NW-6 3 /4 (9.05).5 (8.58) (304.80) 3.00 (76.0) PV NW NW-6 3 /4 (9.05).5 (8.58) 4 (609.60) 3.00 (76.0) PV NW NW-6 3/4 (9.05).5 (8.58) 36 (94.40) 3.00 (76.0) PV NW NW-6 3 /4 (9.05).5 (8.58) 7 (88.80) 3.00 (76.0) PV-00--NW NW-5 (5.40).375 (34.93) (304.80) 4.00 (0.60) PV-00-4-NW NW-5 (5.40).375 (34.93) 4 (609.60) 4.00 (0.60) PV NW NW-5 (5.40).375 (34.93) 36 (94.40) 4.00 (0.60) PV-00-7-NW NW-5 (5.40).375 (34.93) 7 (88.80) 4.00 (0.60) PV-50--NW NW-40 / (38.0).000 (50.80) (304.80) 6.00 (5.40) PV-50-4-NW NW-40 / (38.0).000 (50.80) 4 (609.60) 6.00 (5.40) PV NW NW-40 / (38.0).000 (50.80) 36 (94.40) 6.00 (5.40) PV-50-7-NW NW-40 / (38.0).000 (50.80) 7 (88.80) 6.00 (5.40) PV-00--NW NW-50 (50.80).500 (63.50) (304.80) 8.00 (03.0) PV-00-4-NW NW-50 (50.80).500 (63.50) 4 (609.60) 8.00 (03.0) PV NW NW-50 (50.80).500 (63.50) 36 (94.40) 8.00 (03.0) PV-00-7-NW NW-50 (50.80).500 (63.50) 7 (88.80) 8.00 (03.0) Length SPEIFITIONS Nominal ID sizes: / to inch ( mm) Materials Hose: Wire reinforced polyvinyl chloride (PV) Nipples: 304 stainless steel s: 304 stainless steel (36L available on request) Vacuum Range: > x 0 - Rough vacuum Maximum Temperature: -4º to 65º 89

75 Weld SETION.0 Fittings General Information SPEIFITIONS Tube sizes: / to inches ( mm) Materials: 304 or 36L stainless steel Vacuum range: x 0-3 mbar Temperature range: -00º to 450º Nor-al Products has served industry and research for over 55 years as a premier source for manufactured stainless steel weld fittings. We worked with Lawrence Livermore National Laboratory in the 960 s to develop their specification for vacuum piping, which has become the standard in the industry. Weld fittings are commonly used in vacuum roughing lines on semiconductor process equipment and for foreline and pump exhaust lines in semiconductor subfabs. ll tees and crosses are fabricated with the pulled-port technique and full penetration butt welds, providing crevice-free weld joints and the maximum in cleanliness for UHV applications. Weld fittings are available from stock in 304 stainless steel. Some sizes are stocked in 36L stainless steel for additional corrosion resistance. ll weld fittings are available with various flange combinations. Please refer to the appropriate flange fittings section in this catalog. eadblasted Finish Tumbled Finish Tube Finishes The standard finish for all weld fittings is tumbled, although there are some fittings that are not available with the tumbled finish. These weld fittings are bead-blasted and are designated by a - suffix on the part number. (See photo at right) ll weld fittings can be electropolished on request. all for pricing. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 90

76 Weld Fittings onical Reducers & End aps SETION.0 onical Reducers onical reducers provide a compact means of adapting to a smaller diameter tube with minimal loss in conductance. They are available from stock in 304 stainless steel. Some sizes are stocked in 36L stainless steel for additional corrosion resistance. onical adapter nipples are available with various flange combinations. See appropriate section. TUE TUE WLL THIKNESS -3W (5.40) 3 /4 (9.05).38 (35.05) (.65) -3W / (38.0) 3 /4 (9.05).38 (60.45) (.65) -3W / (38.0) (5.40).38 (60.45) (.65) -3W (50.80) (5.40).38 (60.45) (.65) -3W (50.80) / (38.0).38 (60.45) (.65) -3W / (63.50) / (38.0).38 (60.45) (.65) -3W / (63.50) (50.80).38 (60.45) (.65) -3W (76.0) / (38.0) 3.6 (9.95) (.65) -3W (76.0) (50.80) 3.6 (9.95) (.65) -3W (76.0) / (63.50) 3.6 (9.95) (.65) -3W (0.60) / (38.0) 3.6 (9.95) (.65) -3W (0.60) (50.80) 3.6 (9.95) (.65) -3W (0.60) / (63.50) 3.6 (9.95) (.65) -3W (0.60) 3 (76.0) 3.6 (9.95) (.65) -3W (5.40) 3 (76.0) 5.50 (39.70) (.88) -3W (5.40) 4 (0.60) 5.50 (39.70) (.88) -3W HW 6 (5.40) 4 (0.60) 5.50 (39.70) (.) 36L onical Reducers TUE TUE WLL THIKNESS -3W L (50.80) (5.40).38 (60.45) (.65) -3W L (50.80) / (38.0).38 (60.45) (.65) -3W L 3 (76.0) (50.80) 3.6 (9.95) (.65) -3W L- 4 (0.60) / (38.0) 5.5 (33.35) (.65) -3W L 4 (0.60) (50.80) 3.6 (9.95) (.65) End aps Tube TUE WLL THIKNESS G-W-050 / (.70) 0.3 (8.3) (.7) G-W /4 (9.05) 0.3 (7.87) (.7) G-W-00 (5.40) 0.43 (0.9) (.5) G-W-50 / (38.0) 0.56 (4.) (.5) G-W-00 (50.80) 0.75 (9.05) (.5) G-W-50 / (63.50) 0.70 (7.78) (.5) G-W (76.0) 0.67 (7.0) (.88) G-W (0.60) 0.48 (.9) (.88) G-W / (4.30) 0.5 (.95) (.5) G-W (5.40) 0.88 (.35) (.88) G-W (03.0) 0.83 (.08) (.88) End ap Reducers TUE TUE ER /4 (9.05) / (.70).38 (60.45) ER (5.40) / (.70).38 (60.45) ER (5.40) 3 /4 (9.050).38 (60.45) ER / (38.0) / (.70).38 (60.45) ER / (38.0) 3 /4 (9.05).38 (60.45) ER / (38.0) (5.40).38 (60.45) ER (50.80) / (38.0).38 (60.45) ER / (63.50) (50.80).38 (60.45) ER (76.0) / (38.0) 3.6 (9.95) ER (76.0) (50.80) 3.6 (9.95) ER (76.0) / (63.50) 3.6 (9.95) ER (0.60) (50.80) 3.6 (9.95) ER (0.60) 3 (76.0) 3.6 (9.95) ER (5.40) 4 (0.60) 3.6 (9.95) ER (03.0) 6 (5.40) 3.6 (9.95) Other reducer combinations can be supplied upon request. SPEIFITIONS Tube sizes: to 6 inches ( mm) Materials: 304 or 36L stainless steel Vacuum range: x 0-3 mbar Temperature range: -00º to 450º 9

77 Weld SETION.0 Fittings Elbows SPEIFITIONS Tube sizes: / to 0 inches (.7-54mm) Materials: 304 or 36L stainless steel Vacuum range: x 0-3 mbar Temperature range: -00º to 450º Nor-al Products offers 80 return bend radius elbows in sizes up to inches (50.8mm) and 45º and 90º radius elbows in sizes up to 0 inches (54mm). Radius elbows offer the highest conductance geometry in a tube bend. ll elbows are available from stock in 304 stainless steel, and some sizes are stocked in 36L stainless steel for additional corrosion resistance. We have added several 45º and 90º elbows with tangents to match other commonly available dimensions. Look for the HW suffix for elbows that match HPS weld fitting dimensions, for example. Elbows are also available with various flange combinations. See appropriate section. 80 Return end Radius Elbows TUE WLL THIKNESS G-WU-050 / (.70) (.4) 0.75 (9.05) G-WU /4 (9.05) (0.89).00 (5.40) G-WU-00 (5.40) (.65).50 (38.0) G-WU-50 / (38.0) (.65).5 (57.5) G-WU-00 (50.80) (.65) 3.00 (76.0) ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. 45 Radius Elbows TUE WLL THIKNESS 36L TNGENT G-WK-050 / (.70) (.4) 0.3 (7.87) 0.75 (9.05) G-WK /4 (9.05) (0.89) 0.4 (0.4).00 (5.40) G-WK-075T 3 /4 (9.05) (.65) 0.4 (0.4).3 (8.70) G-KL /4 (9.05) (0.89) 0.76 (9.30).00 (5.40) P G-WK-00 (5.40) (.65) 0.6 (5.75).50 (38.0) G-WK-00-36L (5.40) (.65) 0.6 (5.75).50 (38.0) P G-KL-00 (5.40) (.65) 0.97 (4.64).50 (38.0) P G-KL-00HW (5.40) (.65).9 (30.3).50 (38.0) P G-KL-00-36L (5.40) (.65) 0.97 (4.64).50 (38.0) P P G-WK-50 / (38.0) (.65) 0.93 (3.6).5 (57.5) G-WK-50-36L / (38.0) (.65) 0.93 (3.6).5 (57.5) P G-KL-50 / (38.0) (.65).53 (35.86).5 (57.5) P G-KL-50HW / (38.0) (.65).63 (4.40).5 (57.5) P G-KL-50-36L / (38.0) (.65).53 (35.86).5 (57.5) P P G-WK-00 (50.80) (.65).4 (3.50) 3.00 (76.0) G-WK-00-36L (50.80) (.65).4 (3.50) 3.00 (76.0) P G-KL-00 (50.80) (.65).84 (46.74) 3.00 (76.0) P G-KL-00HW (50.80) (.65).3 (58.67) 3.00 (76.0) P G-KL-00-36L (50.80) (.65).84 (46.74) 3.00 (76.0) P P G-WK-50 / (63.50) (.65).55 (39.37) 3.75 (95.5) G-WK-50-36L / (63.50) (.65).55 (39.37) 3.75 (95.5) P G-KL-50 / (63.50) (.65) 3.00 ( (95.5) P G-WK (76.0) (.65).86 (47.4) 4.50 (4.30) G-WK L 3 (76.0) (.65).86 (47.4) 4.50 (4.30) P G-KL (76.0) (.65) 3.68 (93.47) 4.50 (4.30) P G-KL L 3 (76.0) (.65) 3.68 (93.47) 4.50 (4.30) P P G-WK (0.60) (.).49 (63.5) 6.00 (5.40) G-WK L 4 (0.60) (.).49 (63.5) 6.00 (5.40) P G-KL (0.60) (.) 4.78 (.4) 6.00 (5.40) P G-KL-400HW 4 (0.60) (.) 4.8 (.7) 6.00 (5.40) P G-KL L 4 (0.60) (.) 4.78 (.4) 6.00 (5.40) P P G-WK (5.40) (.) 3.73 (94.74) 9.00 (8.60) G-WK (03.0) ( ) 4.97 (6.4).00 (304.80) G-WK (54.00) ( ) 6. (57.73) 5.00 (38.00) Elbow without Tangent 45 o 45 o Elbow with Tangent 9

78 Weld Fittings Elbows & all Sockets SETION.0 90 Radius Elbows Elbow without Tangent Elbow with Tangent Typ. Typ. TUE WLL THIKNESS 36L TNGENT G-W-050 / (.70) (.4) 0.75 (9.05) 0.75 (9.05) G-W /4 (9.05) (0.89).00 (5.40).00 (5.40) G-W-075H 3 /4 (9.05) (0.89).4 (36.07).00 (5.40) P G-W-00 (5.40) (.65).50 (38.0).50 (38.0) G-W-00-36L (5.40) (.65).50 (38.0).50 (38.0) P G-W-00H (5.40) (.65).8 (46.3).50 (38.0) P G-W-00HW (5.40) (.65).06 (5.3).50 (38.0) P G-W-00H-36L (5.40) (.65).8 (46.3).50 (38.0) P P G-W-50 / (38.0) (.65).5 (57.5).5 (57.5) G-W-50-36L / (38.0) (.65).5 (57.5).5 (57.5) P G-W-50H / (38.0) (.65).4 (6.).5 (57.5) P G-W-50HW / (38.0) (.65).94 (74.68).5 (57.5) P G-W-50HL / (38.0) (.65) 4.97 (6.4).5 (57.5) P G-W-50H-36L / (38.0) (.65).4 (6.).5 (57.5) P P G-W-00 (50.80) (.65) 3.00 (76.0) 3.00 (76.0) G-W-00-36L (50.80) (.65) 3.00 (76.0) 3.00 (76.0) P G-W-00H (50.80) (.65) 4.06 (03.) 3.00 (76.0) P G-W-00HL (50.80) (.65) 5.36 (36.4) 3.00 (76.0) P G-W-00H-36L (50.80) (.65) 4.06 (03.) 3.00 (76.0) P P G-W-50 / (63.50) (.65) 3.75 (95.5) 3.75 (95.5) G-W-50-36L / (63.50) (.65) 3.75 (95.5) 3.75 (95.5) P G-W-50H / (63.50) (.65) 5.9 (3.83) 3.75 (95.5) P G-W (76.0) (.65) 4.50 (4.30) 4.50 (4.30) G-W L 3 (76.0) (.65) 4.50 (4.30) 4.50 (4.30) P G-W-300H 3 (76.0) (.65) 6.3 (60.7) 4.50 (4.30) P G-W (0.60) (.) 6.00 (5.40) 6.00 (5.40) G-W L 4 (0.60) (.) 6.00 (5.40) 6.00 (5.40) P G-W-400H 4 (0.60) (.) 8.3 (.07) 6.00 (5.40) P G-W (5.40) 0.09 (.77) 9.00 (8.60) 9.00 (8.60) G-W (03.0) ( ).00 (304.80).00 (304.80) G-W (54.00) ( ) 5.00 (38.00) 5.00 (38.00) SPEIFITIONS Tube sizes: / to 0 inches (.7-54mm) Materials: 304 stainless steel (36L available upon request) Vacuum range: x 0-3 mbar Temperature range: -00º to 450º 90 Mitered Elbow TUE WLL THIKNESS E-075M 3 /4 (9.05) (0.89).00 (5.40) E-00M (5.40) (.65).88 (47.75) E-50M / (38.0) (.65).5 (57.5) E-50MH / (38.0) (.65).4 (6.) E-00M (50.80) (.65) 3.00 (76.0) E-00MH (50.80) (.65).6 (66.9) E-50M / (63.50) (.65) 3.00 (76.0) E-50MV / (63.50) (.65) 3.75 (95.5) E-300M 3 (76.0) (.65) 3.5 (8.55) E-400M 4 (0.60) (.) 3.88 (98.55) E-400MV- 4 (0.60) (.) 4.87 (3.70) E-500M- 5 (7.00) (.) 4.5 (07.95) E-600M- 6 (5.40) (.) 5.00 (7.00) E-600MV- 6 (5.40) (.) 6.06 (53.9) E-800M- 8 (03.0) 0.0 (3.05) 7.00 (77.80) E-000M- 0 (54.00) 0.0 (3.05) 9.50 (4.30) Typ. 93

79 Weld SETION.0 Fittings Tees 304 stainless steel tees and reducer tees are fabricated with the pulledport technique and full penetration welds. This provides crevice-free weld joints and the maximum in cleanliness for UHV applications. Other sizes are available on request. We have added tees to match other commonly available dimensions. Look for the HW suffix for tees that match HPS weld fitting dimensions, for example. These fittings are also offered with various flange combinations. See appropriate flange section. Tees TUE WLL THIKNESS G-7W-050 / (.70) (.4) 0.75 (9.05) G-7W /4 (9.05) (0.89).00 (5.40) G-7W-075HW 3/4 (9.05) (.65).88 (47.75) G-7W-075T 3 /4 (9.05) (.65).00 (5.40) G-7W-00 (5.40) (.65).88 (47.75) G-7W-50 / (38.0) (.65).5 (57.5) G-7W-50H / (38.0) (.65).4 (6.) G-7W-00 (50.80) (.65) 3.00 (76.0) G-7W-00H (50.80) (.65).6 (66.9) G-7W-50 / (63.50) (.65) 3.00 (76.0) G-7W-50V / (63.50) (.65) 3.75 (95.5) G-7W (76.0) (.65) 3.5 (8.55) G-7W (0.60) (.) 3.88 (98.55) G-7W-400V 4 (0.60) (.) 4.87 (3.70) G-7W (7.00) (.) 4.5 (07.95) G-7W (5.40) (.) 5.00 (7.00) G-7W-600V- 6 (5.40) (.) 6.06 (53.9) G-7W (03.0) 0.0 (3.05) 7.00 (77.80) G-7W (54.00) 0.0 (3.05) 9.50 (4.30) Typ. Tube Typ. Tube 3 SPEIFITIONS Tube sizes: / to 0 inches (.7-54mm) Materials: 304 or stainless steel (36L available upon request) Vacuum range: x 0-3 mbar Temperature range: -00º to 450º Tube Typ. ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. Reducer Tees TUE & RM TUE 3 LEG G-7WR (5.40) / (.70).88 (47.75).00 (5.40) G-7WR (5.40) 3 /4 (9.05).88 (47.75). (8.45) G-7WR / (38.0) / (.70).5 (57.5).5 (3.75) G-7WR / (38.0) 3 /4 (9.05).5 (57.5).38 (35.05) G-7WR / (38.0) (5.40).5 (57.5).3 (54.0) G-7WR (50.80) / (.70) 3.00 (76.0).50 (38.0) G-7WR (50.80) 3/4 (9.05) 3.00 (76.0).63 (4.40) G-7WR (50.80) (5.40) 3.00 (76.0).38 (60.45) G-7WR (50.80) / (38.0) 3.00 (76.0).50 (63.50) G-7WR / (63.50) / (38.0) 3.00 (76.0).75 (69.85) G-7WR / (63.50) (50.80) 3.00 (76.0) 3.5 (8.55) G-7WR (76.0) / (38.0) 3.5 (8.55) 3.00 (76.0) G-7WR (76.0) (50.80) 3.5 (8.55) 3.50 (88.90) G-7WR (76.0) / (63.50) 3.5 (8.55) 3.5 (8.55) G-7WR (0.60) / (38.0) 3.88 (98.55) 3.50 (88.90) G-7WR (0.60) (50.80) 3.88 (98.55) 4.00 (0.60) G-7WR (0.60) / (63.50) 3.88 (98.55) 3.75 (95.5) G-7WR (0.60) 3 (76.0) 3.88 (98.55) 3.75 (95.5) G-7WR (7.00) 4 (0.60) 4.5 (07.95) 4.38 (.5) G-7WR (5.40) / (38.0) 5.00 (7.00) 4.50 (4.30) G-7WR (5.40) (50.80) 5.00 (7.00) 5.00 (7.00) G-7WR (5.40) / (63.50) 5.00 (7.00) 4.75 (0.65) G-7WR (5.40) 4 (0.60) 5.00 (7.00) 4.88 (3.95) G-7WR (5.40) 5 (7.00) 5.00 (7.00) 4.75 (0.65) G-7WR (03.0) 6 (5.40) 7.00 (77.80) 6.00 (5.40) 94

80 Weld Fittings rosses SETION stainless steel crosses and reducer crosses are offered in a wide range of sizes as standard products. ll crosses are fabricated with the pulled-port technique and full penetration butt welds. This provides crevice-free weld joints and the maximum in cleanliness for UHV applications. s always, other sizes are available on request. These fittings are offered with various flange combinations. See appropriate sections. 4-Way rosses TUE WLL THIKNESS G-9W-050 / (.70) (.4) 0.75 (9.05) G-9W /4 (9.05) (.89).00 (5.40) G-9W-00 (5.40) (.65).88 (47.75) G-9W-50 / (38.0) (.65).5 (57.5) G-9W-50H / (38.0) (.65).4 (6.) G-9W-00 (50.80) (.65) 3.00 (76.0) G-9W-00H (50.80) (.65).6 (66.9) G-9W-50 / (63.50) (.65) 3.00 (76.0) G-9W-50V / (63.50) (.65) 3.75 (95.5) G-9W (76.0) (.65) 3.5 (8.55) G-9W (0.60) (.) 3.88 (98.55) G-9W-400V 4 (0.60) (.) 4.87 (3.70) G-9W (7.00) (.) 4.5 (07.95) G-9W (5.40) (.) 5.00 (7.00) G-9W-600V- 6 (5.40) (.) 6.06 (53.9) G-9W (03.0) 0.0 (3.05) 7.00 (77.80) G-9W (54.00) 0.0 (3.05) 9.50 (4.30) Typ. Typ. 5-Way rosses TUE WLL THIKNESS G-0W /4 (9.05) (0.89).00 (5.40) G-0W-00 (5.40) (.65).88 (47.75) G-0W-50 / (38.0) (.65).5 (57.5) G-0W-00 (50.80) (.65) 3.00 (76.0) G-0W-50 / (63.50) (.65) 3.00 (76.0) G-0W-50V / (63.50) (.65) 3.75 (95.5) G-0W (76.0) (.65) 3.5 (8.55) G-0W (0.60) (.) 3.88 (98.55) G-0W-400V- 4 (0.60) (.) 4.87 (3.70) G-0W (7.00) (.) 4.5 (07.95) G-0W (5.40) (.) 5.00 (7.00) G-0W-600V- 6 (5.40) (.) 6.06 (53.9) G-0W (03.0) 0.0 (3.05) 7.00 (77.80) G-0W (54.00) 0.0 (3.05) 9.50 (4.30) 6-Way rosses TUE WLL THIKNESS G-W /4 (9.05) (0.89).00 (5.40) G-W-00 (5.40) (.65).88 (47.75) G-W-50 / (38.0) (.65).5 (57.5) G-W-00 (50.80) (.65) 3.00 (76.0) G-W-50 / (63.50) (.65) 3.00 (76.0) G-W-50V / (63.50) (.65) 3.75 (95.5) G-W (76.0) (.65) 3.5 (8.55) G-W (0.60) (.) 3.88 (98.55) G-W-400V- 4 (0.60) (.) 4.87 (3.70) G-W (7.00) (.) 4.5 (07.95) G-W (5.40) (.) 5.00 (7.00) G-W-600V- 6 (5.40) (.) 6.06 (53.9) G-W (03.0) 0.0 (3.05) 7.00 (77.80) G-W (54.00) 0.0 (3.05) 9.50 (4.30) Typ. 95

81 Weld SETION.0 SPEIFITIONS Tube sizes: 3 /4 to inches ( mm) Materials: 304 or stainless steel (36L available upon request) Vacuum range: x 0-3 mbar Temperature range: -00º to 450º Tube Typ. Tube 3 Tube 4 Tube M Typ. Fittings Reducer rosses & Stainless Steel Tubing Reducer rosses TUE & RM TUE 3 & 4 LEG M G-9WR (5.40) / (.70).88 (47.75).00 (5.40) G-9WR (5.40) 3 /4 (9.05).88 (47.75). (8.45) G-9WR / (38.0) / (.70).5 (57.5).5 (3.75) G-9WR / (38.0) 3 /4 (9.05).5 (57.5).38 (35.05) G-9WR / (38.0) (5.40).5 (57.5).3 (54.0) G-9WR (50.80) / (.70) 3.00 (76.0).50 (38.0) G-9WR (50.80) 3 /4 (9.05) 3.00 (76.0).63 (4.40) G-9WR (50.80) / (38.0) 3.00 (76.0).50 (63.50) G-9WR / (63.50) / (38.0) 3.00 (76.0).75 (69.85) G-9WR / (63.50) (50.80) 3.00 (76.0) 3.5 (8.55) G-9WR (76.0) / (38.0) 3.5 (8.55) 3.00 (76.0) G-9WR (76.0) (50.80) 3.5 (8.55) 3.50 (88.90) G-9WR (76.0) / (63.50) 3.5 (8.55) 3.5 (8.55) G-9WR (0.60) / (38.0) 3.88 (98.55) 3.50 (88.90) G-9WR (0.60) (50.80) 3.88 (98.55) 4.00 (0.60) G-9WR (0.60) / (63.50) 3.88 (98.55) 3.75 (95.5) G-9WR (0.60) 3 (76.0) 3.88 (98.55) 3.75 (95.5) G-9WR (7.00) 4 (0.60) 4.5 (07.95) 4.38 (.5) G-9WR (5.40) / (38.0) 5.00 (7.00) 4.50 (4.30) G-9WR (5.40) (50.80) 5.00 (7.00) 5.00 (7.00) G-9WR (5.40) / (63.50) 5.00 (7.00) 4.75 (0.65) G-9WR (5.40) 3 (76.0) 5.00 (7.00) 4.75 (0.65) G-9WR (5.40) 4 (0.60) 5.00 (7.00) 4.88 (3.95) G-9WR (5.40) 5 (7.00) 5.00 (7.00) 4.75 (0.65) G-9WR (03.0) 6 (5.40) 7.00 (77.80) 6.00 (5.40) Other reducer combinations can be supplied upon request. 304 & 36L Stainless Steel Tubing Nor-al Products consumption of stainless steel tubing for its own products makes it possible to offer 304 and 36L stainless steel tubing in lengths up to 0 feet. 304 stainless steel tubing standard finishes are white pickled (Number unpolished), bright annealed or polished and ID, depending on the size. 36L stainless steel tubing is offered with a bright annealed finish only. right annealed and polished tubing has been pickled and passivated. Polished tube can be described as No. 4 polished. The surface meets STM 70, and has received a 50 grit polish on the and 80 grit on the ID. Special cleaning, materials and surface finishes are available for an additional charge. SPEIFITIONS Tube sizes: / to inches ( mm) Materials: 304 or 36L stainless steel Finishes: right nnealed, polished ID & & white pickled Vacuum range: x 0-3 mbar Temperature range: -00º to 450º ll dimensions are in inches (mm) & weights are in pounds (kg), unless otherwise noted. SURFE FINISH TUE TUE ID WLL THIKNESS SST-050 right annealed / (.70) 0.40 (0.) (.4) SST-075 right annealed 3 /4 (9.05) (7.7) (0.89) SST L right annealed 3 /4 (9.05) (7.7) (0.89) SST-00 Polished ID & (5.40) (.0) (.65) SST-00-36L right annealed (5.40) (.0) (.65) SST-5 right annealed /4 (3.75).0 (8.45) (.65) SST-50 Polished ID & / (38.0).370 (34.80) (.65) SST-50-36L right annealed / (38.0).370 (34.80) (.65) SST-6 right annealed 5 /8 (4.8).490 (37.85) (.65) SST-75 right annealed 3 /4 (44.45).630 (4.40) (.65) SST-00 Polished ID & (50.80).870 (47.50) (.65) SST-00-36L right annealed (50.80).870 (47.50) (.65) SST-50 Polished ID & / (63.5).370 (60.0) (.65) SST-50-36L right annealed / (63.5).370 (60.0) (.65) SST-300 Polished ID & 3 (76.0).870 (7.90) (.65) SST L right annealed 3 (76.0).870 (7.90) (.65) SST-400 Polished ID & 4 (0.60) (97.38) (.) SST L right annealed 4 (0.60) (97.38) (.) SST-500 White pickled 5 (7.00) (.78) (.) SST-600 White pickled 6 (5.40) (48.8) (.) SST-800 White pickled 8 (03.0) (97.0) 0.0 (3.05) SST-000 White pickled 0 (54.00) (47.90) 0.0 (3.05) SST-00 White pickled (304.80).760 (98.70) 0.0 (3.05) * utting fee applies, call for pricing. To order specify length required in feet as follows: SST (0 length of 4 tube) SST-50-36L-0.0 (0 length of.5 tube) 96

82 Order SETION.3 Information Regional Sales ontacts Manufacturing & orporate Global Headquarters 967 South Oregon Street, Yreka, Phone: Toll Free: Fax: Silicon Valley Sales & pplications Office 3375 Scott lvd., Suite 00, Santa lara, Phone: Fax: DIRET SLES: Locate your sales representative at or call for assistance Send drawings and quote requests to Follow us on Sylvie ouhier European Regional Sales Manager Ph: +44 (0) Nor-al Products, Europe Suite D, Dittons Engineering Park Dittons Road, Polegate N6 6HY United Kingdom Ph: +44 (0) Lena Tan sia-pacific Regional Sales Manager Ph: Nor-al Products, sia Pacific ng Mo Kio Street 64 #0-03 EON Industrial uilding Singapore MILING DDRESS: Nor-al Products, sia Pacific Serangoon Garden P. O. ox 48 Singapore 9553 IT Jang South Korea Regional Sales Manager Ph: Nor-al Products, South Korea Gadong nd Floor, 53-8 Gajang-ro, Osan-si, Gyeonggi-do, South Korea, 803 Republic of Korea Ph: Fax:

83 SETION.4 Order Order Information & Warranty Information Terms & onditions of Sale Payment terms are net 30 days from the date of the invoice once credit has been approved. Otherwise,.O.D. Most major credit cards are accepted. If payment in full is not received within 30 days, a.5% per month late charge may be added to the unpaid balance. Discounts may be revoked if an account is not paid within these terms. MINIMUM ORDERS: The minimum domestic order is $40. The minimum international order is $ QUNTITY PRIING: Quantity pricing is valid on single shipments only. VILILITY: Our inventory is updated automatically, but there is always a possibility that an item may be unavailable or sold-out. If this occurs, customers are notified as soon as possible and alternative options are offered if available. PKGING: The factory will determine the most cost effective method to package items for shipment. $5.00 USD per cardboard box charge will be applied to all orders with a maximum charge of $5.00 USD per shipment. Large products requiring a wooden crate will be charged an amount consistent with the fabrication of the necessary crate. FO POINT: ll orders ship FO Yreka from 967 S. Oregon, Yreka, alifornia, 96097, US unless quoted otherwise. LOST OR DMGED ITEMS: Nor-al does not assume responsibility for items lost or damaged in transit, or for any direct or indirect damages incurred. Shipping damages are to be handled by the customer. Nor-al will provide the tracking number and contact information for the shipping company as needed. ll items are purchased at the customer s risk. EXPORTED OMMITIES: US Export administration Regulations must be followed. Diversion contrary to US Law is prohibited. Pricing & Dimensions In order to meet the changing needs of our customers we periodically make design revisions in our standard product line. s a result, the dimensions, pricing and specifications are subject to change without notice. International pricing may also vary. SPEIL TOOLING: Products ordered to non-standard specifications should state specification requirements in detail. Fee for special tooling may apply. On request, test report(s) and/or certification(s) can be supplied at additional cost. Discounts OEM and quantity discounts are available to qualified customers. Return Policy n RM (Return Materials uthorization) number must be obtained from Nor-al Products before returning any merchandise. The RM form can be found under SUPPORT in the footer of pages at To expedite the assignment of an RM number, complete the form online and submit online. You may also print and the completed form to rma@n-c.com or fax to the attention of the RM oordinator at Nor-al Products reserves the right to refuse the return of non-stocked items. twenty-five (5) percent restocking fee may be charged. Nor-al Products shall incur no liability for damage, shortages or other cause alleged to have occurred at, or prior to, delivery to the carrier unless buyer shall have entered full details thereof on its receipt to the carrier. Products over 60 days old from the date of shipment will not be accepted for return. Nor-al Products must be allowed time to investigate all returns. ancellations & Rescheduling ny request by customers to reschedule or cancel in total or part of any purchase order must be approved at the sole discretion of Nor-al Products and shall be subject to the following conditions. Nor-al must receive written notice of Request for ancellation or Reschedule, stating the reasons therefore. ustomer shall be liable for payment of the ollowing charges to Nor-al in the event of ancellation or Reschedule. For all charges incurred (including overhead, G&, and profit) prior to the date that notice of cancellation is received by Nor-al for all parts peculiar to customer s requirements. Upon payment by the customer of these charges, such parts become the property of customer, Nor-al will store said parts for a reasonable period of time pending the receipt of customer s instructions for disposition. Such storage is at customer s risk and may be subject to storage charges if stored by Nor-al for longer than 30 days from the cancellation date; plus harges to convert modified standard parts for return to Nor-al s inventory; plus restocking charge of twenty (5) percent of the purchase price of the cancelled item. Warranty Products manufactured by Nor-al Products are warranted against defects in material and workmanship for a period of twelve () months from the date of shipment from Nor-al Products to the buyer. ny modification to the product by the buyer or their agent voids this warranty. Liability under this warranty is expressly limited to the replacement or repair (at Nor-al Products option) of defective parts. Nor-al Products may at any time discharge its warranty as to any of its products by refunding the purchase price and taking back the products. This warranty applies only to parts manufactured and labor provided by Nor-al Products under valid warranty claims received by Nor-al Products within the applicable warranty period and shall be subject to the terms and conditions hereof. Expendable items such as tubes, heaters, sources, bellows, etc., by their nature, may not function for one year; if such items fail to give reasonable service for a reasonable period of time, as determined solely by Nor-al Products, they will be repaired or replaced by Nor-al Products at its election. ll warranty replacement or repair of parts shall be limited to equipment malfunctions which, in the sole opinion of Nor-al Products, are due or traceable to defects in original materials or workmanship. Malfunctions caused by abuse or neglect of the equipment are expressly not covered by this warranty. Nor-al Products expressly disclaims responsibility for any loss or damage caused by the use of its products other than in accordance with proper operating and safety procedures. Reasonable care must be taken be the user to avoid hazards. The buyer shall give Nor-al Products prompt notice of any claim under this warranty. If Nor-al Products, in its sole discretion, determines that the product does not conform to this warranty, Nor-al Products shall replace or repair the product free of charge. If such replacement or repair is not feasible, Nor-al Products may, at its sole option, refund the purchase price. In-warranty repaired or replacement parts are warranted only for the remaining unexpired portion of the original warranty period applicable to the parts which have been repaired or replaced. fter the expiration of the applicable warranty period, the buyer shall be charged at Nor-al Products then current prices for parts and labor plus transportation. Except as stated herein, Nor-al Products makes no warranty, expressed or implied (either in fact or operation of law), statutory or otherwise: and, except as stated herein, Nor-al Products shall have no liability for special or consequential damages of any kind or from any cause arising out of the sale, installation, or use of any of its products. Statements made by any person, including representatives of Nor-al Products, which are inconsistent or in conflict with the terms of this warranty shall not be binding upon Nor-al unless reduced to writing and approved by an officer of Nor-al Products. This warranty shall not extend to any product, that in Nor-al Products judgment, has been affected by damage or wear resulting from operations performed after the sale, or misuse, abrasion, negligence, accident, tampering, faulty installation, inadequate maintenance, damage or casualty. DISLIMER OF WRRNTY: NOR-L MKES NO WRRNTIES WITH RESPET TO THIS SLE, WHETHER EXPRESSED OR IMPLIED, EXEPT S STTED HEREIN, NOR-L PRUTS MKES NO WRRNTY OF MERHNTILITY OR FITNESS FOR PRTIULR PURPOSE. LIMITTION OF REMEDY ND DMGES: THE EXLUSIVE REMEDY OF THE UYER WITH RESPET TO THE TRNSTIONS ONTEMPLTED HEREIN SHLL E THE REPLEMENT OR REPIR OF SID PRUTS, OR THE RETURN OF THE PURHSE PRIE, S SET FORTH UNDER WRRNTY. EXEPT S HEREIN PROVIDED, EVERY FORM OF LIILITY FOR DIRET OR ONSEQUENTIL DMGE FOR LOSS, RISING FROM ONTRT, TORT OR OTHERWISE, IS EXPRESSLY EXLUDED ND DENIED, INLUDING WITHOUT LIMITTION, LOSS OR DMGES TO UILDINGS, ONTENTS, PRUTS OR PERSONS. 9

84 Order SETION.5 Information Patents & Trademarks Nor-al Products, Inc. patents and trademarks: Genesis Modular Valves are manufactured under patent number Intellisys Pressure ontrol Products are manufactured under patent number 6633 Genesis is a trademark of Nor-al Products, Inc. Intellisys is a registered trademark of Nor-al Products, Inc. Other registered patents and trademarks: Magnetic Linear/Rotary Feedthroughs are manufactured under patent number Sample Transfer Systems are manufactured under patent number lumel is a registered trademark of oncept lloys, Inc. ajon is a registered trademark of Swagelok ompany hemraz is a registered trademark of Greene Tweed ompany hromel is a registered trademark of oncept lloys, Inc. onflat is a registered trademark of Varian ssociates orp. DeviceNet is a trademark of the Open DeviceNet Vendor ssociation (V) Dupra is a registered trademark of Daikin Industries, Ltd. Ethernet is a trademark of Xerox orporation EV-eFix is a registered trademark of EV G Inconel is a registered trademark of Special Metals orp. KF is a registered trademark of Leybold Vacuum Products Inc. Kalrez is a registered trademark of DuPont Dow Elastomers Kovar is a registered trademark of RS Holdings Inc. Macor is a registered trademark of orning, Inc. Microdot is a registered trademark of Tyco Electronics orp. Modbus is a registered trademark of Schneider Electric US Inc. Omicron is a registered trademark of Omicron Electric GmbH Penduroll is a patented technology of V-Tex orporation Perlast is a registered trademark of Precision Polymer Engineering LTD. SolidWorks is a registered trademark of Dassault Systémes SolidWorks orp. Swagelok is a registered trademark of Swagelok ompany UL is a registered trademark of Underwriters Laboratories, Inc. VR is a registered trademark of Swagelok ompany Windows is a registered trademark of Microsoft orporation 30

85 Nor-al Products, Inc. 967 South Oregon Street Yreka, alifornia or Fax: