POWERLine. WIESEL POWERLine WM with ball screw drive and integrated linear ball-bearing guide. Unit conversions.

Size: px

Start display at page:

Download "POWERLine. WIESEL POWERLine WM with ball screw drive and integrated linear ball-bearing guide. Unit conversions."

Maurice Dorsey
6 years ago
Views:

1 WIESEL WM with bll screw drive nd integrted liner bll-bering guide Technicl dt Liner speed: mx. 2.5 m/s Repetbility: ± 0.03 mm Accelertion: mx. 10 m/s 2 Rottionl speed: mx rpm Drive element: pretensioned bll screw drive with single nut, no bcklsh Dimeter: mm Led: , 20, 50 mm Stroke length: mm Power bridge: mm long Geometricl moment of inerti:...ly 5.8 x 10 5 mm 4 lz 5.9 x 10 5 mm 4 Weights Bsic unit with zero stroke: kg 100 mm stroke: kg Power bridge with crrige: kg Provided: pieces KAO mounting brckets Lods nd lod moments Lod dynm. [N] Fx drive 2800 Fy 1400 ± Fz 1400 Lod moment dynm. [Nm] Mx 50 My 100 Mz 100 Unit conversions Length: 1 m=1000 mm=39.37 inches 1 inch=25.4 mm Force: 1 N=0.225 lbf 1 lbf=4.45 N Moment of Force: 1 Nm=0.738 lb ft=8.85 lb inches 1 lb ft=1.36 Nm Geometricl moment of inerti: 1 m 4 =10 12 mm 4 = x 10 6 in 4 Mss moment of inerti: 1 kg m2 =10 4 kg cm2 =0.738 lb ft s 2 Mss: 1 kg=2.2 lb All figures shown in millimeters. Idle rques [Nm] Rottionl speed Led P [mm] [rpm] Additionl lengths s function of the stroke Stroke length [mm] A [mm] B [mm] Additionl length C [mm]

2 WIESEL nd WIESEL DYNALine WIESEL nd WIESEL DYNALine Selection of liner units with bll screw drivedrive with screw drive bestbll solution for down every ppliction Innovtive solutions, the very lst detil. Selection of liner drive units best solution for every ppliction Innovtive solutions, down the very lst detil. Guide system/lod High performnce smll liner drive unitwith for extremely miniturized pplictions. dimensions. Precision Technology USA, Inc. High performnce with extremely smll Bll screw bll screw drive combintion with theusa, high Inc. dimensions. inprecision Technology precision llows precise positioning. bll screwliner driveguide in combintion with the high precision liner guide llows precise positioning. Fx Rep. v 12 kn ± 0.01 mm 2.5 m/s 20 m/s2 Externl Fx Rep. v minimum. Fx 5 kn Rep. ± 0.05 mm v 10 m/s 40 m/s2 Screw sport ptented Screw sportscrew sport system permits high sport speeds ptented screw (mx. input speed) t system permits high speeds long (mx.strokes. input speed) t Centrl lubriction A stndrd feture. drive Centrl lubriction nd guide systems A stndrd feture. re drive conveniently relubricted nd guide systems re from centrlrelubricted point on the conveniently power bridge. Whether by from centrl point on the hnd or umticlly, mintepower bridge. Whether by nnce now simple mintemtter. hnd orisumticlly, long strokes. (1124 lbf) (0.002 in) (33 ft/s) (131 ft/s2) nnce is now simple mtter. Precise positioning is mde possible by polished liner Externl guide with high degree of guide ccurcy. A smll mor cn be dded thnks the low coefficient of friction. Rubber wipers protect the mechnism from dirt, thus incresing service life. 12 kn ± 0.01 mm 2.5 m/s 20 m/s2 (2698 lbf) ( in) (8.2 ft/s) (65 ft/s2) Internl Toothed belt drive Well proven nd ptented guide systemnd ptented Well proven high-performnce liner guide system bll-bering guide with liner high-performnce hrdened steel running bll-bering guide with trcks hs been integrted intrcks the hrdened steel running luminum profile. Optimum hs been integrted in the introduction of forces permits luminum profile. Optimum mximum force nd rque, introduction of forces permits s well s force optimizing the mximum nd rque, tensile s well stresses. s optimizing the tensile stresses. WIESEL WM60, WM120 WIESELWM80, WM60, WM80, WM120 is n WIESEL WIESEL Mnger/CAD-dt liner drive WIESEL ispckge nunit with powerful Get the extremely WIESEL Mnger softwre for the selection nd plnning of ll Precision Technology USA, Inc. liner bll screw drive nd integrted bllextremely powerful liner drive with drive units s well s our CAD-dt. Clickunit or send the order form on pge 102. Also benefit from bering guide. It llows high feed forces bll screw drive nd integrted blltechnicl consulttion service. nd lodguide. moments in llhigh directions. bering It llows feed forces nd lod moments in ll directions. performnce vlues of the Notes: Fx -Feed force respective sizes cn be found Rep.-Repetbility on pge 12. v -Liner speed Internl Toothed belt drive Guide system/lod Liner guides Bll screw (2698 lbf) ( in) (8.2 ft/s) (65 ft/s2) Ptented seling strip ptented seling Ptented seling stripstrip protects the mechnism ptented seling strip effectively from dirt. protects the mechnism friction for the devition effectively from dirt. of the seling stripdevition is reduced friction for the of minimum. the seling strip is reduced Drive WIESEL WM40 Drive liner drive unit for miniturized WIESEL WM40 pplictions. -Accelertion Bll cge bll berings of the liner guides re protected by bll cge. y cn be replced quickly nd sfely. Fx Rep. v 5 kn ± 0.05 mm 10 m/s 40 m/s2 Self-djusting thirdgenertion cover strip ptented seling strip relibly protects the mechnicl prts ginst excessive dirt nd is retensioned umticlly. Result: the mintennce effort is reduced virtully zero. Optimized bll screw pre-tensioning of the nut unit cn be djusted by the Precision Technology USA, Inc. service tem. This increses the lifetime of the xis. (1124 lbf) (0.002 in) (33 ft/s) (131 ft/s2) FEA optimized design Both the profile nd the entire liner drive unit hve been modeled nd optimized by finite element nlysis (FEA). Result: mximum performnce density nd relibility. WIESEL DYNALine WV60, WV80, WV120 WIESEL Mnger/CAD-dt WIESEL DYNALine permits Get the WIESEL Mnger softwre pckge for the selection nd plnning of ll Precision Technology USA, Inc. even linerin high feed forces, drive units s well s our CAD-dt. Click or send the order form on pge 102.combintion Also benefit from with long stroke technicl consulttion service. lengths nd high speeds. sported, covered bll screw must be used in performnce vlues of the Notes: Fx -Feed force combintion with externl respective sizes cn be found Rep.-Repetbility liner guides. on pge 12. v -Liner speed -Accelertion WIESEL DYNALine detil Precision Technology Precision Technology WIESEL detil WIESEL detil *only pplies WIESEL series Precision Technology

Mechnicl liner drive units WIESEL, WIESEL DYNALine, WIESEL VARIOLine WIESEL WM40 Fully integrted miniturized liner drive unit with liner bll guide, bll screw drive nd seling strip.

3 Mechnicl liner drive units WIESEL, WIESEL DYNALine, WIESEL VARIOLine WIESEL WM40 Fully integrted miniturized liner drive unit with liner bll guide, bll screw drive nd seling strip. WIESEL WM60/80 ZRT Fully integrted drive unit with oth belt drive nd liner bering guide. Trnsmission of the feed force nd hndling of lods nd lod moments. WIESEL VARIOLine Fully integrted liner drive unit with bll screw nd liner bll bering guide nd seling strip. Trnsmission of the feed force nd hndling of lods through rm type pisn. WIESEL WM60/80/120 Fully integrted liner drive unit with bll screw nd liner bll bering guide nd seling strip. Trnsmission of the feed force nd hndling of lods nd lod moments. Size WM60/ with short guide system. WIESEL DYNALine WV60/80/120 Fully integrted feed xis with bll screw. Trnsmission of the feed force. Used in combintion with externl liner guides. WIESEL DYNALine, WIESEL, WIESEL VARIOLine profile sectionl views

Generl technicl dt WIESEL, DYNALine, VARIOLine Liner speeds liner speed chieved by liner drive unit depends on the led of the mechnicl drive element nd on the input rottionl speed.

4 KGT 2) 4 3000 0.2 5 3000 0.25 10 3000 0.5 20 3000 1 40 3000 2 50 3000 2.5 VARIOLine 3000 1.5 ZRT 3) 20ATL5 120 1250 2.5 ZRT 3) 25ATL10 170 882 2.

4 Generl technicl dt WIESEL, DYNALine, VARIOLine Liner speeds liner speed chieved by liner drive unit depends on the led of the mechnicl drive element nd on the input rottionl speed. vrious liner speeds which cn be chieved by the individul sizes re listed in the following tble: Drive Led nmx vmx element [mm] [rpm] [m/s] TGT KGT 2) VARIOLine ZRT 3) 20ATL ZRT 3) 25ATL TGT: Trpezoidl screw drive 2) KGT: Bll screw drive 3) ZRT: Toothed belt drive Instlled position liner drive units cn be instlled in lmost ny position, provided tht ll the forces nd moments occurring remin below the mximum vlues for the xis concerned. Security dvice bll screw drives in ll three sizes re generlly not self-locking. It is therefore dvisble instll suitble mors with holding brke, prticulrly if the liner drive unit is instlled verticlly. If the othed belt breks, the lod is relesed. refore sfety precutions hve be tken for pplictions which re criticl with regrd security. Mximum forces All mximum forces nd moments provided refer the center/p of the power bridge. Lod overly t severl coordintes: If compound lods occur, with force nd moment components in more thn one direction, the mximum permissible lods must be reduced 60% of the specified mximum vlues. When forces nd moments re overlid in two or three coordintes, it is necessry reduce the mximum permissible lod 60% of the mximum vlue. Duty cycle In prctice, the following vlues hve been proven. Drive element: For trpezoidl screw the per limit should be 30% per hour, liner bll guides llow duty cycles 100%. Extremely high lods in combintion with high duty cycles cn reduce the life. Guidnce element: For sliding guide the per limit should be 30% per hour, liner bll guides llow duty cycles 100%. Temperture All series re designed for continuous opertion t mbient tempertures 80 C (176 F). Tempertures 100 C (212 F) re lso permitted for brief periods. liner drive units re not suitble for opertion t subzero tempertures. Idle rques given vlues re mens from series of mesurements. effective vlues my differ in individul cses. Strightness/rsion luminum profiles re extruded sections which my disply devitions in strightness nd rsion due their mnufcturing process. lernce of these devitions is defined in DIN devitions found in Precision Technology USA, Inc. liner drive units corresponding these limits re worst cse, but re normlly well below. In order obtin the required guide ccurcy, the liner drive unit must be ligned with the id of leveling pltes or clmped from mounting surfce mchined with sufficient ccurcy. This ensures tht lernces of t lest 0.1 mm/1000 mm re chieved. Cover strip for WIESEL WIESEL DYNALine WIESEL VARIOLine Mteril: Polymide 12 Chrcteristics: Resistnt lkline solutions Conditionlly resistnt cids Tough/rigid Abrsion-proof Little bsorption of humidity Light resistnt Guide tube All the components of liner drive unit except the mechnicl drive element re ccommodted in guide tube which is mounted either the botm of driven WIESEL or is instlled prllel driven WIESEL. It tkes higher lods nd lod moments. All WIESEL models re lso vilble s guide tube (except WIESEL DYNALine, VARIOLine ). Stroke length stroke length specified in the order code represents the mximum possible liner displcement. Accelertion nd decelertion pths must be tken in ccount when designing the system, gether with ny overrun required. Entering the sfety zone leds mechnicl collisions nd must be prevented with suitble sfety mesures (sfety limit switch, softwre queries, etc.) Repetbility repetbility is defined s the cpbility of liner drive unit repetedly rech n ctul position it hs reched before under the sme conditions. It refers the verge position vrition ccording VDI/DGQ repetbility is influenced, mong other things, by: Lod Speed Decelertion/ccelertion Direction of trvel Temperture Aggressive working environments mechnicl drive nd the guidnce of the WIESEL re well protected ginst dirt by mens of the ptented cover strip. In cses of hevy dirt nd dust prticles, n dditionl bellow is recommended. Avilble on request. Mintennce mechnicl components (bll screw drive nd liner bll bering guide) must be lubricted vi the grese nipple on the power bridge with the id of grese gun fter 400 hours of opertion or t lest every three months. On the WM40, one lubriction nipple is used lubricte the liner guidewy, while the second lubriction point splies the bll screw drive with grese. cover strip should lso be lubricted t the sme time in order prevent premture wer. Grese: rolling bering grese (originl grese Fuchs Lubritec URETHYN E/M. Tensioning of the othed belt tensioning of the othed belt cn be djusted with the id of the tensioning screws on the guide csing which re intended for this. liner units re delivered with optiml tension vlues in order gurntee security nd functionlity. Chnges in this djustment must be crried out in service cses nd by Precision Technology USA, Inc. service engineers.

5 Accessories for WIESEL Mounting brckets KAO Mounting brckets WIESEL unit is secured mounting surfce by mens of the KAO mounting brckets which re inserted in the grooves provided in the sides of the tubulr luminum profile nd screwed on the mounting surfce with the id of socket hed cp screws. number of mounting brckets required depends on the lod nd overll length of the WIESEL unit. This is shown in the digrms. Incresing side forces reduces the distnce between sports. Ech unit is provided with 4 pieces KAO Mounting brckets. Mximum rque of mounting screws Size Moment [Nm] WM WM/WV WM/WV WM/WV KAO System brckets Only needed for WH40. With multi-coordinte rrngements of severl WIESEL units, this cn be used mount WIESEL directly the power bridge of unit positioned immeditely below. Dimension [mm] Size A B C D ø E F ø G H WM WM/WV WM/WV WM/WV WM40 System KAO WM60 System KAO Note: It is dvisble secure the liner drive unit t intervls of t lest 750 mm. This ensures tht ll the permissible lods cn be bsorbed without significntly deforming the tubulr luminum profile.

6 Accessories for WIESEL Long power bridge WM40 WM60 LKB Long power bridge long power bridge increses the mximum permissible lod moments My nd Mz of WIESEL unit without requiring step size. difference in length between the long power bridge nd the stndrd power bridge must be tken in ccount when clculting the overll length of the WIESEL unit. Overll length of the WIESEL unit: WM80 Lt = Stroke + C + Kb C* = Specific dditionl length Lt = Overll length WIESEL unit Stroke = Required stroke length Kb = Difference in length between long nd stndrd power bridge * Clcultion in depency of stroke nd Kb. dimension C is shown in the chrts of technicl dt of the corresponding ctur. WM120 Size Length of power bridge My Mz [mm] [Nm] [Nm] WM WM WM WM Note: All other limit vlues re comprble those of versions with stndrd power bridge. High lod moments led mjor deformtion of the tubulr luminum profile. distnce between sports should be reduced on order minimize this deformtion. Note: All other limit vlues ccording executions with stndrd power bridge. All figures shown in millimeters. Unit conversions Length: Force: Moment of Force: 1 m=1000 mm=39.37 inches 1 inch=25.4 mm 1 N=0.225 lbf 1 lbf=4.45 N 1 Nm=0.738 lb ft=8.85 lb inches 1 lb ft=1.36 Nm Geometricl moment of inerti: 1 m 4 =10 12 mm 4 = x 10 6 in 4 Mss moment of inerti: 1 kg m 2 =10 4 kg cm 2 =0.738 lb ft s 2 Mss: 1 kg=2.2 lb

7 Accessories for WIESEL Additionl free-sliding power bridge OKB Additionl free-sliding power bridge dditionl free-sliding power bridge provides: Individul increse of the lod moments My nd Mz of WIESEL unit. Lod moment My is limited by force ± Fz; Mz is limited by force ±Fy. Longer nd therefore improved guidnce. Prticulrly suitble s verticl guide nd lifting module. required center distnce between the driven nd the free-sliding power bridge is clculted s follows: LA = M Fmx LA M Fmx = Distnce between center of driven power bridge nd center of free-sliding power bridge [mm] = Lod moment My or Mz [mm] = Mximum force Fz or Fy of the WIESEL unit concerned [N] center distnce between the two power bridges must be tken in ccount when clculting the overll length of the WIESEL unit. Overll length of WIESEL unit Lt = Stroke + LC + LA Unit conversions Length: Force: Moment of Force: 1 m=1000 mm=39.37 inches 1 inch=25.4 mm 1 N=0.225 lbf 1 lbf=4.45 N 1 Nm=0.738 lb ft=8.85 lb inches 1 lb ft=1.36 Nm Lc = Specific dditionl length [mm] between long nd stndrd power bridge. (see technicl dt of the respective WIESEL ) Minimum center distnce between driven nd free-sliding power bridge (given for stndrd power bridge). Size LA [mm] WM40* min 175 mx 600 WM WM WM *For stroke lengths of more thn 1700 mm plese contct our product specilists for the mximum screw rottionl speed. required force move the dditionl free sliding power bridge must be tken in ccount when selecting the drive. Size F [N] WM40 40 WM WM WM Note: High lod moments led mjor deformtion of the tubulr luminum profile. In order minimize this deformtion, the distnce between the fixing points should be reduced. Geometricl moment of inerti: 1 m 4 =10 12 mm 4 = x 10 6 in 4 Mss moment of inerti: 1 kg m 2 =10 4 kg cm 2 =0.738 lb ft s 2 Mss: 1 kg=2.2 lb

8 Accessories for WIESEL, DYNALine Mechnicl limit switches ES Mechnicl limit switches Mechnicl limit switches must be used wherever people my be jeoprdized if the electric drive does not cut out. y re fitted in the groove which lso ccommodtes the KAO mounting brckets in the luminum profile nd cn be djusted by mens of the oblong hole provided. Technicl dt CAM-ctuted mechnicl limit switch XCM-B516 with roller lever. Dul-circuit NC + NO NC contct forcibly opened in ccordnce with DIN EN Type of protection: IP 67 Mx. perm. strting speed: 1.5 m/s All figures shown in millimeters. Size Dimensions [mm] A B C D E F G for WM G for WV WM/WV WM/WV WM/WV Note: Fixing of the liner unit by mens of the KAO mounting brckets is not possible in the re of the bse pltes of the mechnicl limit switches. Unit conversions Length: Force: Moment of Force: 1 m=1000 mm=39.37 inches 1 inch=25.4 mm 1 N=0.225 lbf 1 lbf=4.45 N 1 Nm=0.738 lb ft=8.85 lb inches 1 lb ft=1.36 Nm Geometricl moment of inerti: 1 m 4 =10 12 mm 4 = x 10 6 in 4 Mss moment of inerti: 1 kg m 2 =10 4 kg cm 2 =0.738 lb ft s 2 Mss: 1 kg=2.2 lb

9 Generl ccessories Inductive proximity switch EN inductive proximity switch Inductive proximity switches re used shut down the electric drive before the mechnicl limit position hs been reched. Operting point brking pth depends on the liner speed nd time-lg. This pth must t lest be llowed between the operting point of the proximity switch nd the ctul mechnicl limit position. Inductive proximity switches re lso used identify reference points or signl operting points the control system. Normlly-closed versions re used for limit positions nd normlly-open versions for operting points. proximity switches cn be infinitely djusted in the guide rils. ENT 18.5x20 All figures shown in millimeters. Technicl dt Contctless inductive proximity switch with LED disply in plstic housing. Operting distnce: 2 mm Type of protection: IP 67 Power sply: V DC Mx. lod current: 200 ma Screened connection cble, length 2 m or 10 m. Size Type Cble length Weight [m] [kg] EN2 O-normlly closed EN2 S-normlly open EN2 O-normlly closed EN2 S-normlly open WIESEL Ordering ENT 13.2x13.2 ENT limit switch brcket A sport profile for mounting nd djusting inductive proximity switch EN. hollow provides spce route cbles for the cble hrness of proximity switch nd cn be conceled with cover tpe. ENT 14x16 Size WH40/50/80/120 WHZ50/80 WM40/60/80/120 WV60/80 Type ENT 14x16 ENT 14x16 ENT 14x16 ENT 14x16 All figures shown in millimeters. Unit conversions Length: Force: Moment of Force: 1 m=1000 mm=39.37 inches 1 inch=25.4 mm 1 N=0.225 lbf 1 lbf=4.45 N 1 Nm=0.738 lb ft=8.85 lb inches 1 lb ft=1.36 Nm Geometricl moment of inerti: 1 m 4 =10 12 mm 4 = x 10 6 in 4 Mss moment of inerti: 1 kg m 2 =10 4 kg cm 2 =0.738 lb ft s 2 Mss: 1 kg=2.2 lb

10 Exmples Prllel rrngement: 2 WIESEL SPEEDLine 1 Universl joint shft 2-xis rrngement: X-xis: 2 WIESEL SPEEDLine 1 Universl joint shft WIESEL Ordering Y-xis: 1 WIESEL SPEEDLine 2-xis rrngement: X-xis: 1 WIESEL 1 WIESEL s guide tube Z-xis: 1 WIESEL 3-xis rrngement: X-xis: 2 WIESEL with bevel gerbox 1 Universl joint shft Z-xis: 1 WIESEL TM Y-xis: 1 WIESEL 1 WIESEL s guide tube

11 Lod rtings WIESEL Dynmic lod rtings With the help of dynmic lod rtings, it is possible clculte the pproximte lifetime, dependent on lod. figures shown re for the KGT, ccording DIN 69051, Prt 4, Drft 1989, nd for the guide, ccording DIN 636. Type CKGM P=4 CKGM P=5 CKGM P=10 CKGM P=20 CKGM P=40 CKGM P=50 CFS Y CFS Z LFS X LFS Y [N] [N] [N] [N] [N] [N] [N] [N] [mm] [mm] WH40 (2x) 2786 (2x) WH50 (4x) WH80 (4x) WH120 (4x) WHZ50 (4x) WHZ80 (4x) WM (2x) 2786 (2x) WM ZRT (2x) (2x) WM (2x) (2x) WM (4x) (4x) WM (4x) (4x) WM ZRT (2x) (2x) WM80 ZRT (4x) (4x) WM (2x) (2x) WM (4x) (4x) WM (4x) (4x) WV WV WV WIESEL Ordering Importnt note: permissible force nd moment threshold vlues for the respective liner unit must not be exceeded t ny time. Unit conversions Length: Force: Moment of Force: 1 m=1000 mm=39.37 inches 1 inch=25.4 mm 1 N=0.225 lbf 1 lbf=4.45 N 1 Nm=0.738 lb ft=8.85 lb inches 1 lb ft=1.36 Nm Geometricl moment of inerti: 1 m 4 =10 12 mm 4 = x 10 6 in 4 Mss moment of inerti: 1 kg m 2 =10 4 kg cm 2 =0.738 lb ft s 2 Mss: 1 kg=2.2 lb

12 Drive selections for liner drive units with bll screw drive Feed force Fx [N] Accelertion force F [N] Power from rque nd rottionl speed [kw] Fx = m g µ F = m In verticl pplictions, the mss ccelertion must be dded the ccelertion due grvity g [9.81 m/s 2 ]. P = MA nmx 2 π Definitions MA = Required drive moment [Nm] m = Mss be trnsported [kg] Mlod = Moment resulting from the vrious lods [Nm] = Accelertion [m/s 2 ] Midle = Idle rque [Nm] p = Screw pitch [mm] Mrot = Rottionl ccelertion moment [Nm] P = Power [kw] Mtrns = Trnsltionl ccelertion moment [Nm] L = WIESEL length [mm] Fx = Feed force [N] nmx = Mximum rottionl speed [rpm] F = Accelertion force [N] µ = Friction fcr g = Accelertion due grvity [m/s 2 ] jsp = Mss moment of inerti of the screw per meter [kgm 2 /m] Vmx = Mximum liner speed [m/s] Clculting the drive moment MA [Nm] required drive moment is composed of the lod moment, the ccelertion moment nd the idle rque. MA = Mlod + Mtrns + Mrot + Midle Mrot = vlue for the respective idle rque cn be found with the corresponding mechnicl liner drive units. jsp L nmx 2 π Vmx WIESEL Ordering Mtrns = F p 2 π 1000 Mlod = Fx p 2 π 1000 MA Totl = Friction fcr µ Mss moment of inerti jsp Vlues for µ lubricted Type P [mm] jsp[kgm 2 /m] WIESEL WM WIESEL WM/WV x 10-5 WIESEL WM60/80/ x 10-5 WIESEL DYNALine Friction vlue of the externl guide x 10-5 WIESEL /DYNALine 80 5, 10, 20, x 10-4 WIESEL / DYNALine x , 20, x 10-4 WIESEL WM40 4, x 10-5

13 Order informtion WIESEL, WIESEL DYNALine, WIESEL VARIOLine Structure of the order code: / Product WV = WIESEL DYNALine WM = WIESEL WZ = WIESEL VARIOLine 6. Mx. liner trvel [mm] 7. Totl length [mm] 9. Specil model 0 = No 1 = briefly described in words Ordering exmple: 2. Size 40, 60, 80 nd Design model 000 = Stndrd 190 = Guide tube (only WM) 370 = Short guidnce system 8. Mounted ccessories EN = Inductive proximity switches ES = Mechnicl limit switches (Not for WM40) OKB = Additionl power bridge (specify center distnce the driven power bridge) 4. Drive type LKB = Long power bridge M = Single nut (only for WM40, WM40) WM60/80-370) KRG = Mounted bevel gerbox (specify type nd MM = Bll screw drive with pretensioned nut unit ZR = Belt drive RT trnsmission rtio) = Belt drive (specify trnsmission rtio) ADG = Mounted shft encoder 5. Led 5, 10, 20, 40 or 50 mm Size 60 = 120 mm Size 80 = 170 mm (specify number of pulses nd version) MGK = Mounted mor dpter PRT = Prllel belt drive system (only for WM 40) WM/ MM E N-K R G Product 2. Size Design model Stndrd 4. Drive type Pretensioned nut unit MM 5. Led 20 mm 6. Mx. liner trvel 700 mm 7. Totl length 1260 mm 8. Mounted ccessories 3 inductive proximity switches (normlly 2 NC nd 1 NO), mounted bevel gerbox 9. Specil model 1 = mounted bevel gerbox VL1B40, trnsmission i = 1 :1 WIESEL Ordering Definition of the drive shft within the order code Drive shft execution AZ6/D/N Execution vrieties of the drive shft: 0 = plin N = with keywy D = shft end prepred for mounting of shft encoder Definition of the drive shft within the order code Drive shft execution AZ1 Drive shft execution AZ2 Exmple: Drive shft execution AZ6, side AZ1 prepred for mounting of shft encoder, side AZ2 with keywy.

WIESEL SPEEDLine WHZ80 with roller guideway and AT toothed belt

WIESEL SPEEDLine WHZ80 with roller guideway and AT toothed belt WIESEL WHZ80 with roller guideway and AT toothed belt All figures shown in millimeters. Note: Mounted wipers on request. The use of a long power bridge increases the total length. Technical data Linear