LW Series offer flexibility in space-saving package
|
|
- Jodie Bell
- 6 years ago
- Views:
Transcription
1 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) LW Series offer flexibility in space-saving package Key features include: P board mount, solder or screw terminal ollective mounting saves space Non-reflective lens Highly visible marking plate Tamper proof construction Light touch reduces strain or silver contacts emovable contacts simplify wiring and facilitate PB applications UL ecognized File # E55996 LW Series Switches and Pilot Devices: 7/8" (22mm) S ertified File No. L21451 LW Series switches and pilot lights can be mounted collectively on 1.0" centers. ombined with pcb terminals and locking lever removable contacts, this eases manufacture of pre-fab pushbutton arrays (as pictured). P Board tracing/soldering of contacts can be done in tandem with panel cutting/operator installation. ll LW series units mount by means of a locking ring that comes on from the rear of the panel, as such they can not be removed from outside the panel and are relatively tamperproof. ombining the snap action and tactile feel of miniature commercial pushbuttons with the size and ruggedness of industrial pushbuttons, LW pushbuttons are a unique solution to many applications. hoose from standard silver contacts or low-level gold plated contacts. Terminals available in.110" solder tab, M3 screw, or pcb pins. egistration No. J US: (800) 262-IDE or (408) , anada (888) 317-IDE -57
2 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) Specifications ontact atings Operating Temperature Storage Temperature Operating Humidity ontact esistance Insulation esistance Dielectric Strength Vibration esistance Shock esistance Mechanical Life Electrical Life Lamp atings Voltage 6V /D ±5% 12V /D ±10% 24V /D ±10% 120V ±10% LED Incandescent Switch Unit Illumination Unit Degree of Protection Insulation Voltage Lenses Materials Operators Marking Plates Terminal Style 25 to +60 (without freezing) LED illuminated type: 25 to to to 85% H 50mΩ maximum (initial value) 100MΩ minimum (500V D megger) Between live part and ground: 2,500V, 1 minute Between terminals of different poles: 2,500V, 1 minute Between terminals of the same pole: 1,000V, 1 minute Between live part and ground: 2,500V, 1 minute Operating extremes: 5 to 55Hz, mplitude 1.0mm p-p Damage limits: 1,000 m/sec 2 (pprox. 100G) Operating extremes: 100 m/sec 2 (pprox. 10G) Momentary: 1,000,000 operations minimum Maintained: 500,000 operations minimum Selector: 250,000 operations minimum Illuminated Selector: 250,000 operations minimum Momentary: 100,000 operations minimum (at 1,800 operations/hour) Maintained/Selector: 100,000 operations minimum (at 900 operations/hour) Watertight/oiltight IP65 (IE Pub529) (except key selectors) 250V/D polyarylate polyacetate acrylic resin.110" Solder tab quick connect P board terminal (gold contacts only) Screw terminal (DPDT units only) ontact Material Thermal urrent ontact ating emarks -clad cross-bar ontact V /D ±5% 1W 12V /D ±10% 24V /D ±10% urrent/wattage 20m 20m 20m 10m 1W 1W 30VD/0.1 resistive 125V/0.1 resistive 30VD/2 resistive 30VD/1 inductive 125V/3 resistive(50/60hz) 125V/2 inductive (50/60Hz) 125VD/0.4 resistive 125VD/0.2 inductive 250V/2 resistive(50/60hz) 250V/1.5 inductive (50/60Hz) LED lamps contains a built-in current-limiting resistor and reverse polarity protection diode. Minimum applicable load (reference value): 5V, 1m /D. (pplicable range is subject to the operating condition and load.) inductive load: PF=0.6 to 0.7, D inductive load: L/=7ms maximum. UL ecognized File # E55996 S ertified File No. L21451 egistration No. J US: (800) 262-IDE or (408) , anada (888) 317-IDE
3 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) s: LW1B/LW2B Pushbuttons ontact Style ontact Momentary Maintained (Latching) Material Solder/Tab P Board Screw Solder/Tab P Board Screw Flush Flush Extended Extended Mushroom Non-Illuminated Pushbuttons (ssembled) SPDT LW1B-M11-1 LW1B-M11V-1 LW1B-11-1 LW1B-11V-1 DPDT LW1B-M12-1 LW1B-M12V-1 LW1B-M12M-1 LW1B-12-1 LW1B-12V-1 LW1B-12M-1 3PDT LW1B-M13-1 LW1B-M13V-1 LW1B-13-1 LW1B-13V-1 SPDT LW1B-M15-1 LW1B-15-1 DPDT LW1B-M16-1 LW1B-M16M-1 LW1B-16-1 LW1B-16M-1 3PDT LW1B-M17-1 LW1B-17-1 SPDT LW2B-M11-1 LW2B-M11V-1 LW2B-11-1 LW2B-11V-1 DPDT LW2B-M12-1 LW2B-M12V-1 LW2B-M12M-1 LW2B-12-1 LW2B-12V-1 LW2B-12M-1 3PDT LW2B-M13-1 LW2B-M13V-1 LW2B-13-1 LW2B-13V-1 SPDT LW2B-M15-1 LW2B-15-1 DPDT LW2B-M16-1 LW2B-M16M-1 LW2B-16-1 LW2B-16M-1 3PDT LW2B-M17-1 LW2B-17-1 SPDT LW1B-M21-1 LW1B-M21V-1 LW1B-21-1 LW1B-21V-1 DPDT LW1B-M22-1 LW1B-M22V-1 LW1B-M22M-1 LW1B-22-1 LW1B-22V-1 LW1B-22M-1 3PDT LW1B-M23-1 LW1B-M23V-1 LW1B-23-1 LW1B-23V-1 SPDT LW1B-M25-1 LW1B-25-1 DPDT LW1B-M26-1 LW1B-M26M-1 LW1B-26-1 LW1B-26M-1 3PDT LW1B-M27-1 LW1B-27-1 SPDT LW2B-M21-1 LW2B-M21V-1 LW2B-21-1 LW2B-21V-1 DPDT LW2B-M22-1 LW2B-M22V-1 LW2B-M22M-1 LW2B-22-1 LW2B-22V-1 LW2B-22M-1 3PDT LW2B-M23-1 LW2B-M23V-1 LW2B-23-1 LW2B-23V-1 SPDT LW2B-M25-1 LW2B-25-1 DPDT LW2B-M26-1 LW2B-M26M-1 LW2B-26-1 LW2B-26M-1 3PDT LW2B-M27-1 LW2B-27-1 SPDT LW1B-M31-1 LW1B-M31V-1 LW1B-31-1 LW1B-31V-1 DPDT LW1B-M32-1 LW1B-M32V-1 LW1B-M32M-1 LW1B-32-1 LW1B-32V-1 LW1B-32M-1 3PDT LW1B-M33-1 LW1B-M33V-1 LW1B-33-1 LW1B-33V-1 SPDT LW1B-M35-1 LW1B-35-1 DPDT LW1B-M36-1 LW1B-M36M-1 LW1B-36-1 LW1B-36M-1 3PDT LW1B-M37-1 LW1B In place of 1, specify button color code from table below. 2. For sub-assembly part numbers, see page For dimensions, see page For accessories, see page Button olor ode olor ode Black Green ed Blue White Yellow B G S W Y US: (800) 262-IDE or (408) , anada (888) 317-IDE -59
4 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) s: Operators Style Mushroom s: Buttons Type Mushroom s: ontact Blocks LW Series ontact Block + Operator + Button = ompleted Unit Momentary LW1B-M0 LW2B-M0 LW1B-M0L Flush LW1-B1-1 LW2-B1-1 Maintained LW1B-0 LW2B-0 LW1B-0L ppearance ontact Material ontact Non-Illuminated Pushbuttons (Sub-ssembled) Extended LW1-B2-1 LW2-B2-1 LW1-B3-1 In place of 1, specify Button olor ode from table at right. Solder/Tab P Board Screw SPDT LW-1 LW-1V DPDT LW-2 LW-2V LW-2M 3PDT LW-3 LW-3V SPDT LW-5 DPDT LW-6 LW-6M 3PDT LW-7 1 Button olor ode olor ode Black B Green G ed Blue S White W Yellow Y US: (800) 262-IDE or (408) , anada (888) 317-IDE
5 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) s: LW1L/LW2L Illuminated Pushbuttons (LED and Incandescent) ontact Style ontact Momentary Maintained (Latching) Material Solder/Tab P Board Screw Solder/Tab P Board Screw Mushroom SPDT LW1L-M110-➁ LW1L-M110V-➁ LW1L-110-➁ LW1L-110V-➁ DPDT LW1L-M120-➁ LW1L-M120V-➁ LW1L-M120M-➁ LW1L-120-➁ LW1L-120V-➁ LW1L-120M-➁ 3PDT LW1L-M130-➁ LW1L-M130V-➁ LW1L-130-➁ LW1L-130V-➁ SPDT LW1L-M150-➁ LW1L-150-➁ DPDT LW1L-M160-➁ LW1L-M160M-➁ LW1L-160-➁ LW1L-160M-➁ 3PDT LW1L-M170-➁ LW1L-170-➁ SPDT LW2L-M110-➁ M110V-➁ LW2L-110-➁ LW2L-110V-➁ DPDT LW2L-M120-➁ M120V-➁ LW2L-M120M-➁ LW2L-120-➁ LW2L-120V-➁ LW2L-120M-➁ 3PDT LW2L-M130-➁ LW2L-M130V-➁ LW2L-130-➁ LW2L-130V-➁ SPDT LW2L-M150-➁ LW2L-150-➁ DPDT LW2L-M160-➁ LW2L-M160M-➁ LW2L-160-➁ LW2L-160M-➁ 3PDT LW2L-M170-➁ LW2L-170-➁ SPDT LW1L-M310-➁ M110V-➁ LW1L-310-➁ LW1L-310V-➁ DPDT LW1L-M320-➁ LW1L-M320V-➁ LW1L-M320M-➁ LW1L-320-➁ LW1L-320V-➁ LW1L-320M-➁ 3PDT LW1L-M330-➁ LW1L-M330V-➁ LW1L-330-➁ LW1L-330V-➁ SPDT LW1L-M350-➁ LW1L-350-➁ DPDT LW1L-M360-➁ LW1L-M360M-➁ LW1L-360-➁ LW1L-360M-➁ 3PDT LW1L-M370-➁ LW1L-370-➁ 1. In place of ➁, specify the Lens color code from table below. 2. Lamps must be ordered separately for all illuminated pushbuttons. 3. For marking plate size and engraving area, see page For sub-assembly part numbers, see page For dimensions, see page For accessories, see page -68. s: Lamps Type Voltage urrent LED 6V /D 20m LSTD-6➁ 12V /D 20m LSTD-1➁ 24V /D 20m LSTD-2➁ 120V 10m LSTD-H2➁ 240V ±10% LSTD-M4➁ Incandescent 6.3V /D, 1W IS-6 12V /D, 1W IS-12 24V /D, 1W LED and Incandescent Illuminated Pushbuttons (ssembled) IS In place of ➁, specify the Lens/LED color code. 2. The LED contains a current-limiting resistor and reverse polarity protection diode. 3. To order green LED, use color code G. ➁ Lens/LED olor ode olor ode mber Green ed Blue White Yellow Y * GD is lighter green than GL. GD (LED lenses)* GL (Incandescent lenses) G (LED lamps) S W US: (800) 262-IDE or (408) , anada (888) 317-IDE -61
6 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) ontact Block + Operator + Lamp + Lens = ompleted Unit s: Operators Style Mushroom s: ontact Blocks ppearance ontact Material ontact s: Lamps Type Voltage urrent 6V /D 20m LSTD-6➁ LED 12V /D 20m LSTD-1➁ 24V /D 20m LSTD-2➁ Solder/Tab P Board Screw SPDT LW-10 LW-10V DPDT LW-20 LW-20V LW-20M 3PDT LW-30 LW-30V SPDT LW-50 DPDT LW-60 LW-60M 3PDT LW V 10m LSTD-H2➁ 240V ±10% Incandescent 6.3V /D, 1W IS-6 12V /D, 1W 24V /D, 1W LED and Incandescent Illuminated Pushbuttons (Sub-ssembled) Momentary Maintained LW1L-M0 LW2L-M0 LW1B-M0L LW1L-0 LW2L-0 LW1B-0L LSTD-M4➁ IS-12 IS In place of ➁, specify the LED color code. 2. The LED contains a current-limiting resistor and reverse polarity protection diode. s: Lenses Type Mushroom Flush LW1-L1-➁ LW2-L1-➁ LW1-L3-➁ In place of ➁, specify Lens olor ode from table below. ➁ LED/Lens olor ode olor ode mber Green* ed Blue White GD (LED lenses)* GL (Incandescent lenses) G (LED lamps)) S W Yellow Y * The GD lens is a lighter green than the GL. For green LED, use G as color code US: (800) 262-IDE or (408) , anada (888) 317-IDE
7 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) s: LW1P/LW2P Pilot Lights Type emovable Terminal Pilot Light Short Body Pilot Light Style 1. In place of ➁, specify the Lens/LED color code from table below. 2. For marking plate size and engraving area, see page Lamps must be ordered separately, see table below. 4. For sub-assembly part numbers, see page For dimensions, see page For accessories, see page -68. s: Lamps (not included) Type Voltage urrent LED 6V /D 20m LSTD-6➁ 12V /D 20m LSTD-1➁ 24V /D 20m LSTD-2➁ 120V 10m LSTD-H2➁ 240V ±10% LSTD-M4➁ Incandescent 6.3V /D, 1W IS-6 12V /D, 1W IS-12 24V /D, 1W LED and Incandescent Pilot Lights (ssembled) Solder/Tab P Board Screw LW1P-100V-➁ LW2P-100V-➁ LW1P-10-➁ LW1P-10M-➁ LW2P-10-➁ LW2P-10M-➁ IS In place of ➁, specify the Lens/LED color code. 2. The LED contains a current-limiting resistor and reverse polarity protection diode. 3. To order green LED, use color code G. ➁ Lens/LED olor ode olor ode mber Green ed Blue White Yellow Y * GD is lighter green than GL. GD (LED lenses)* GL (Incandescent lenses) G (LED lamps) S W US: (800) 262-IDE or (408) , anada (888) 317-IDE -63
8 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) emovable Terminal* + Operator + Lamp + Lens = ompleded Unit * emovable terminals are applicable for PB terminated types only. s: Pilot Light Operators Style s: Lenses Type Termination Solder P Board Screw LW1P-00 LW1P-0 LW1P-00M LW2P-00 LW2P-0 LW2P-00M equires LW-00V removable terminals in addition to operator. LW1-P1-➁ LW2-P1-➁ In place of ➁, specify Lens/LED olor ode. s: Lamps (LED) Type Voltage urrent 6V /D 20m LSTD-6➁ LED 12V /D 20m LSTD-1➁ 24V /D 20m LSTD-2➁ 120V 10m LSTD-H2➁ 240V ±10% Incandescent 6.3V /D, 1W IS-6 12V /D, 1W 24V /D, 1W LED and Incandescent Pilot Lights (Sub-ssembled) LSTD-M4➁ IS-12 IS In place of ➁, specify the LED color code. 2. The LED contains a current-limiting resistor and reverse polarity protection diode. ➁ LED/Lens olor ode olor ode mber Green* ed Blue White GD (LED lenses)* GL (Incandescent lenses) G (LED lamps)) S W Yellow Y * The GD lens is a lighter green than the GL.. For green LED, use G as color code US: (800) 262-IDE or (408) , anada (888) 317-IDE
9 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) s: LW1S Selector Switches Style Position ontact Material ontact Solder/Tab P Board Screw SPDT LW1S-21 LW1S-21V 90 2-position maintained DPDT LW1S-22 LW1S-22V LW1S-22M 3PDT LW1S-23 LW1S-23V L SPDT LW1S-25 DPDT LW1S-26 LW1S-26M 3PDT LW1S position DPDT LW1S-32 LW1S-32V LW1S-32M maintained 3PDT LW1S-33 LW1S-33V DPDT LW1S-36 LW1S-36M L 3PDT LW1S-37 s: LW1K Keylock Selector Switches Style Position ontact Material ontact 1. Knob color: Black; Direction al Indication olor: White 2. For contact operation, see next page. 3. For sub-assembly part numbers, see page position maintained L 45 3-position maintained L Solder/Tab P Board Screw SPDT LW1K-21 LW1K-21V DPDT LW1K-22 LW1K-22V LW1K-22M 3PDT LW1K-23 LW1K-23V SPDT LW1K-25 DPDT LW1K-26 LW1K-26M 3PDT LW1K-27 DPDT LW1K-32 LW1K-32V LW1K-32M 3PDT LW1K-33 LW1K-33V DPDT LW1K-36 LW1K-36M 3PDT LW1K-37 s: LW1F LED and Incandescent Illuminated Selector Switches Style Position ontact Material ontact s Solder/Tab P Board Screw SPDT LW1F-210-➁ LW1F-210V-➁ 90 2-position DPDT LW1F-220-➁ LW1F-220V-➁ LW1F-220M-➁ maintained 3PDT LW1F-230-➁ LW1F-230V-➁ L SPDT LW1F-250-➁ DPDT LW1F-260-➁ LW1F-260M-➁ 45 3-position maintained L Selector and Keylock Switches (ssembled) 1. Every key selector uses an identical key. 2. The key is removable in all positions. 3. If a different configuration is required, contact an IDE representative for more information. 4. For contact operation, see next page. 5. For sub-assembly part numbers, see page In place of ➁, specify color code. See previous page for color codes. 2. Lamps must be ordered separately for all illuminated pushbuttons. See previous page. 3. For contact operation, see next page. 4. For sub-assembly part numbers, see page PDT LW1F-270-➁ DPDT LW1F-320-➁ LW1F-320V-➁ LW1F-320M-➁ 3PDT LW1F-330-➁ LW1F-330V-➁ DPDT LW1F-360-➁ LW1F-360M-➁ 3PDT LW1F-370-➁ US: (800) 262-IDE or (408) , anada (888) 317-IDE -65
10 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) ontact Operation: Selector and Keylock Switches L Position 90 2-Position Maintained L 45 3-Position Maintained ontact SPDT DPDT 3PDT DPDT 3PDT Left ontact Operations Operator Position and ontact Position (Top View) Left enter ight Terminal rrangements (Bottom View): LW L and LW B Pushbuttons Lamp Terminal (+) Lamp Terminal ( ) X1 X2 X2 N N ight N Left enter ight N N N Left N ight N Left N _ ight N Left N N ight N Left enter ight N N N Left N ight Left enter ight Left enter ight Left enter ight N N N N N N N N N 3 pole illuminated 2 pole illuminated 3 pole non-illuminated N N N Lamp Terminal (+) Lamp Terminal ( ) SPDT has, and N only on the center. DPDT has,, and N only on the right and left. X1 X2 N N N N N N SPDT has, and N only on the right. DPDT has,, and N only on the right and center US: (800) 262-IDE or (408) , anada (888) 317-IDE
11 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) *Lens for illuminated units only s: Operators * Lens must be purchased separately for illuminated units. s: ontact Blocks ontact Block + Operator + Lens* = ompleded Unit Unit Position Non-Illuminated Selector Switch 2-position LW1S-2Y 3-position LW1S-3Y Key Switch 2-position LW1K-2 Illuminated Selector Switch 3-position 2-position 3-position LW1K-3 LW1F-20* LW1F-30* ppearance Style ontact Material ontact Illuminated Selectors Non-Illuminated Selectors s: Lamps (LED) Type Voltage urrent LED 6V /D 20m LSTD-6➁ 12V /D 20m LSTD-1➁ 24V /D 20m LSTD-2➁ 120V 10m LSTD-H2➁ 240V ±10% LSTD-M4➁ Incandescent 6.3V /D, 1W IS-6 12V /D, 1W IS-12 24V /D, 1W Selectors and Keyswitches (Sub-ssembled) IS In place of ➁, specify the LED color code. 2. The LED contains a current-limiting resistor and reverse polarity protection diode. s: Knob (Lens) Style Illuminated Selector Switches Solder/Tab P Board Screw SPDT LW-10 LW-10V DPDT LW-20 LW-20V LW-20M 3PDT LW-30 LW-30V SPDT LW-50 DPDT LW-60 LW-60M 3PDT LW-70 SPDT LW-1 LW-1V DPDT LW-2 LW-2V LW-2M 3PDT LW-3 LW-3V SPDT LW-5 DPDT LW-6 LW-6M 3PDT LW-7 LW1-F-➁ In place of ➁, specify LED/Lens olor ode from table below. ➁ LED/Lens olor ode olor ode mber Green* ed Blue White GD (LED lenses)* GL (Incandescent lenses) G (LED lamps)) S W Yellow Y * The GD lens is a lighter green than the GL.. For green LED, use G as color code. US: (800) 262-IDE or (408) , anada (888) 317-IDE -67
12 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) Style Description/Usage ing Wrench (optional) 1. Metallic tool used for tightening the plastic locking ring when installing the LW series on a panel. 2. Tightening torque should not exceed 1.2N-m (12 kgf-cm) when tightening a locking ring. LW9Z-T1 Lamp Holder Tool (optional) Terminal over (for solder tab terminal) Terminal over (for screw terminal) Terminal over (for short body pilot light with solder tab terminal) Terminal over (for short body pilot light with screw terminal) ubber Mounting Hole Plug Metallic Mounting Hole Plug eplacement Marking Plates nti-otation ing eplacement Keys For replacement lamps, see previous page. ccessories LW Series ubber tool used for replacing incandescent or LED lamps installed in illuminated switches and pilot lights and pilot lights ø0.452" (ø11.6mm) Nylon cover for pushbuttons and selectors with solder terminals snaps onto contact block. (Insert the lead wires through terminal cover holes before wiring.) Nylon cover for pushbuttons and selectors for screw terminals snaps onto contact block. (Insert the lead wires through terminal cover holes before wiring.) Nylon cover for short body pilot lights with solder terminals. Nylon cover for short body pilot lights with screw terminals. Black rubber plug fills unused 22mm panel cutouts " (3.5mm) ø1.131" (ø29mm) 1. Used for plugging unnecessary mounting holes in the panel. Tighten the attached locking ring to a torque of 1.2N-m (12kgf-cm) maximum 2. Degree of Protection: IP " (12mm) White plastic engraving plate for use on all illuminated units (included in each lens). May be used to capture printed mylar insert (not supplied by IDE) under lens face. Prevents rotation of switches in panel. (included with all assembled switches and operators) One pair of keys. (#231) 0.137" (3.5mm) 2.301" (59mm) ø0.975" (ø25mm) ø1.0" (ø25.8mm) 0.117" (3mm) ing ing ø0.546" (ø14mm) O-55 LW-VL2 LW-VL2M LW-PVL LW-PVLM OB-31 LW9Z-BM LW9Z-P1-W (round) LW9Z-P2-W (square) LW9Z-L KG9Z-SK US: (800) 262-IDE or (408) , anada (888) 317-IDE
13 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) LW L & LW B: Illuminated & Non-Illuminated Pushbuttons M3 Screw Terminal Terminal over LW-VL2M LW L 0.32" (8.2mm) 0.32" (8.2mm) 2.14" (54.9mm) M3 Screw Terminal Terminal over LW-VL2M LW B 2.087" (53.5mm) Screw Terminal ear View 0.663" (17mm) 0.702" (18mm) 0.905" (23.2mm) 2.14" (54.9mm) 0.02" (0.5mm) 0.254" (6.5mm) P Board Terminal 0.31" x 0.02" (0.8 x 0.5mm) 0.047" (1.2mm) 0.991" (25.4mm) LW L Screw Terminal 0.702" (18mm) 0.905" (23.2mm) 0.02" (0.5mm) 0.991" (25.4mm) 0.189" (4.85mm) 0.234" (6mm) 0.21" 1.404" (36mm) (5.4mm) P Board Terminal ø1.17" (ø30mm) LW B Screw Terminal Mushroom Dimensions ccessories LW Series 0.189" (4.85mm) 0.047" (1.2mm) 0.234" (6mm) Dimensions: Pushbuttons 0.702" (18mm) 0.632" (16.2mm) 0.975" (25mm) 0.189" (4.85mm) US: (800) 262-IDE or (408) , anada (888) 317-IDE " (6.5mm) Tab Terminal 0.109" x 0.02" (2.8 x 0.5mm) 0.332" 0.456" (8.5mm) (11.7mm) 1.404" (36mm) Solder/Tab Terminal 0.491" (12.6mm) LW L P Board Terminal 0.702" (18mm) 0.632" (16.2mm) 0.975" (25mm) 0.189" (4.85mm) LW B P Board Terminal Terminal over LW-VL2 Gasket ing ing TOP nti-rotation ing 1.83" (47.0mm) Terminal over LW-VL2 Gasket ing ing Extended 0.71" (18.2mm) 0.632" (16.2mm) TOP nti-rotation ing 1.83" (47.0mm) 0.702" (18mm) ø1.0" (ø25.4mm) ø1.0" (ø25.4mm) 0.975" (25mm) 1.022" (26.2mm) Solder/Tab Terminal Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) LW L LW B 1.0" ( 25.4mm) 1.0" ( 25.4mm) For Panel and Terminal rrangement P Board cutouts, see last page of this dimensions section.
14 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) LW1P/LW2P Pilot Lights Separate Type 0.702" (18mm) 0.632" (16.2mm) Short Body Type 0.975" (25mm) M3 Screw Terminal Terminal over LW-PVLM 0.281" (7.2mm) 0.176" (4.5mm) 0.30" (7.7mm) Terminal rrangement Separate Type Bottom View Lamp Terminal (+) Lamp Terminal ( ) X1 X2 X2 Short Body Type Bottom View Lamp Terminal (+) Lamp Terminal ( ) X2 X1 X " (36mm) Lamp Terminal ( ) 0.443" (11.35mm) 1.045" (26.8mm) 0.047" (1.2mm) Lamp Terminal (+) X2 X " (5.4mm) Dimensions: Pilot Lights Gasket ing ing TOP nti-rotation ing P Terminal 0.31" x 0.02" (0.8 x 0.5mm) 0.332" 0.456" (8.5mm) (11.7mm) 1.404" (36mm) P Board Terminal Terminal over Gasket 0.232" LW-PVL ing ing (5.95mm) nti-rotation ing 1.404" (36mm) 0.263" (6.75mm) 0.234" (6mm) 0.293" (7.5mm) Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) 0.741" (19mm) 1.05" (27mm) Solder/Tab Terminal ø1.0" (ø25.4mm) ø1.0" (ø25.4mm) 1.0" ( 25.4mm) 1.0" ( 25.4mm) US: (800) 262-IDE or (408) , anada (888) 317-IDE
15 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) LW1S and LW1K Selector and Keylock Switches M3 Screw Terminal Terminal over LW-VL2M 0.32" (8.2mm) 2.087" (53.5mm) Screw Terminal Selector ø1.0" (ø25.4mm) ear View 0.702" (18mm) 0.905" (23.2mm) 2.14" (54.9mm) 0.991" (25.4mm) Screw Terminal 0.189" (4.85mm) P Board Terminal 0.31" x 0.02" (0.8 x 0.5mm) 0.047" (1.2mm) 0.02" (0.5mm) ø1.0" (ø25.4mm) 0.21" 1.404" (36mm) (5.4mm) P Board Terminal Keylock (2mm) 0.702" (18mm) 0.632" (16.2mm) 0.975" (25mm) Dimensions: Selector and Keylock Switches P Board Terminal 0.234" (6mm) 0.19" (4.85mm) 0.71" (18.2mm) 0.047" (1.2mm) 0.234" (6mm) 0.632" (16.2mm) Terminal over LW-VL2 Gasket ing ing 0.702" (18mm) TOP nti-rotation ing 1.83" (47.0mm) Tab Terminal 0.109" x 0.02" (2.8 x 0.5mm) 0.332" 0.456" (8.5mm) (11.7mm) 1.404" (36mm) Solder/Tab Terminal 0.975" (25mm) 1.022" (26.2mm) Solder/Tab Terminal Selector Switches 0.683" (17.5mm) Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) Gasket ing ing nti-rotation ing Keylock Switches 1.83" (47.0mm) Tab Terminal 0.109" x 0.02" (2.8 x 0.5mm) 0.332" 0.456" (8.5mm) (11.7mm) 1.404" (36mm) Solder/Tab Terminal Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) 1.443" (37mm) 0.41" (10.5mm) US: (800) 262-IDE or (408) , anada (888) 317-IDE -71
16 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) LW1F LED and Incandescent Illuminated Selector Switches M3 Screw Terminal Terminal over LW-VL2M 0.32" (8.2mm) Layouts LW L P Board Drilling Layout P Board Terminal Bottom View Dimensions: Selector and Keylock Switches, continued and Layouts 2.14" (54.9mm) 2.087" (53.5mm) Screw Terminal ear View 0.702" (18mm) 0.905" (23.2mm) 0.991" (25.4mm) Screw Terminal " (4.85mm) 0.254" (6.5mm) ø0.047" (ø1.2mm) holes Mounting Hole Layout ø0.87" +0.02" - 0 (ø " 0 mm) 1.014" (26mm) Note " (1.2mm) 0.254" (6.5mm) 0.189" (4.85mm) P Board Terminal 0.31" x 0.02" (0.8 x 0.5mm) 0.047" (1.2mm) 0.02" (0.5mm) 0.21" 1.404" (36mm) (5.4mm) P Board Terminal 0.702" (18mm) 0.632" (16.2mm) 0.975" (25mm) P Board Terminal 0.254" (6.5mm) 0.189" (4.85mm) 0.234" (6mm) 0.71" (18.2mm) 0.047" (1.2mm) 0.234" (6mm) 0.632" (16.2mm) Terminal over LW-VL2 Gasket ing ing 0.702" (18mm) TOP nti-rotation ing 1.83" (47.0mm) Tab Terminal 0.109" x 0.02" (2.8 x 0.5mm) 0.332" 0.456" (8.5mm) (11.7mm) 1.404" (36mm) Solder/Tab Terminal 0.975" (25mm) 1.022" (26.2mm) Solder/Tab Terminal LW B P Board Drilling Layout P Board Terminal Bottom View 0.189" (4.85mm) ø0.047" (ø1.2mm) holes 0.047" (1.2mm) 1. When determining mounting centerlines, allow for easy operation. 2. Mushroom (Ø 1.17" (Ø 30mm)) = 1.248" (32mm) Tab terminal = 1.014" (26mm) (with/without terminal cover) P board terminal = 1.014" (26mm) Screw terminal = 1.56" (40mm) 3. Mushroom (Ø 1.17" (Ø 30mm) = 1.248" (32mm) Tab terminal = 1.053" (27mm) (with terminal cover) Tab terminal = 1.014" (26mm) (without terminal cover) P board terminal = 1.014" (26mm) Screw terminal = 1.014" (26mm) 0.683" (17.5mm) Panel Thickness: 0.031" to 0.234" (0.8mm to 6.0mm) 0.02" (0.5mm) ø1.0" (ø25.4mm) Pilot Lights P Board Drilling Layout P Board Terminal Bottom View 0.047" (1.2mm) 0.443" (11.35mm) ø0.047" (ø1.2mm) holes 1.014" (26mm) Note US: (800) 262-IDE or (408) , anada (888) 317-IDE
17 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) eplacement of Lens & Marking Plate emoving 1. emove the operator (lens, marking plate, and lens holder) by inserting a screwdriver into the recess of the lens through the bezel. 2. emove the marking plate by pushing the lens from the rear to disengage the latches between the lens and the lens holder, using the screwdriver as shown below. The translucent filter in the lens holder can not be removed because this filter is sealed to make the unit waterproof and oiltight. Installing For round lens types, place the marking plate on the lens holder with the antirotation projection engaged and press the lens onto the lens holder to engage the latches. For square lens types, insert the marking plate into the lens, and press the lens onto the lens holder to engage the latches. Pay attention to the orientation of the marking plate. Pay attention to the orientation of the marking plate. For Lens Lens Marking Plate Lens Holder eplacement of Lamps Lamps can be replaced using the lamp holder tool (O-55) from the front of the panel. lso by removing the contact block from the operator unit, the lamp can be replaced. eplacement of Lamps from the Front of the Panel. (How to emove) 1. Push and turn the lamp counterclockwise using the side of the lamp holder tool, and the lamp and the lamp holder can be removed. (How to Install) 1. Insert the lamp into the lamp holder tool and hold the lamp as in the following illustration. Lamp Lamp Holder Tool For Lens Instructionsccessories LW Series Lens Marking Plate Lens Holder the same direction. Then push the lamp lightly and turn it clockwise. eplacement of Lamps by emoving the ontact Block The lamp can be replaced by removing the contact block without using the lamp holder tool. Marking Plates & Films For LW series illuminated pushbuttons and pilot lights, legends and symbols can be engraved on marking plates, or printed mylar can be inserted under the lens for labelling purposes. Marking Plate and Marking Film Size Lens Style Lens Lens Built-in Marking Plate pplicable Marking Film Engraving rea ø0.694" (ø17.8mm) 0.033" (0.85mm) Grooves in the Operator Unit Engraving must be made on the engraving area within 0.02" (0.5mm) deep. The marking plate is made of white acrylic resin. Mylar for printing labels are not included and must be provided and printed by user. Two 0.004" (0.1mm)-thick films or one 0.008" (0.2mm)-thick film can be installed in the lens. ecommended marking film: Mylar Insertion Order of Marking Plate & Film For Lens 0.772" (19.8mm) 0.69" (17.7mm) Lens Film Marking Plate Lens Holder 0.033" (0.85mm) Housing Insertion Order of Marking Plate & Film. For Lens 0.772" (19.8mm) Lens Film Marking Plate Lens Holder Housing 1. Mylar is not included. 2. Pay attention to the orientation of marking plate. Engraving rea ø0.683" (ø17.5mm) Top Marking Side Top Marking Side 2. Place the insertion guide of the lamp and the groove in the operator unit in US: (800) 262-IDE or (408) , anada (888) 317-IDE -73
18 ourtesy of Steven Engineering, Inc. 230 yan Way, South San Francisco,, Main Office: (650) Outside Local rea: (800) Panel Mounting emove the contact block from the operator. Insert the operator into the panel cut-out from the front, then install the contact block to the operator. emoving the ontact Block Turn the locking lever on the contact block in the direction opposite to the arrow on the housing. Then the contact block can be removed. Installing the ontact Block Insert the contact block, with the TOP markings on the contact block and the operator placed in the same direction. Then lock the units, turning the locking lever in the direction of the arrow. Notes on Mounting Use the optional ing Wrench (LW9Z-T1) to mount the operator onto a panel. Tightening torque should not exceed 1.2N-m (12 kgf-cm). Do not use pliers. Excessive tightening will damage the locking ring. Wiring 1. Solder the terminals within 20W/5 seconds or 260 /3 seconds without exerting external force to the terminals. While soldering, do not touch the soldering iron to the housing. While wiring, prevent tension from being applied to the terminals. Do not bend or raise the terminals, nor exert excessive force to terminals. 2. Use a non-corrosive resin liquid flux. ollective Mounting s the locking lever can be turned easily from the rear of the units using a screwdriver, the contact blocks can be removed even when mounted collectively. Notes for Terminal over (Solder/Tab Terminal) Insert the terminal cover into the contact block with the TOP markings on the contact block and the terminal cover in the same direction. When wiring, insert the lead wires into the terminal cover holes before wiring. Notes for Wiring When installing a terminal cover onto the solder/tab terminal contact block, solder the inside of lamp terminal (toward the switch terminals) and wire. (Screw Terminal Type) Install a terminal cover to the control unit before wiring. 1. fter wiring, terminal covers cannot be installed. 2. When terminal covers are used, round crimping terminals cannot be used. Instructions con t onnection Positive-lock connector and easy-lock connector are applicable to tab terminals. One Board Mounting Mounting the switches and pilot lights on one P board offers the following features. 1. educed installation labor, easy wiring, space saving, and standardization. 2. Since the contact blocks on the P board can be removed easily using a locking lever, the LW series switches and pilot lights are easy to maintain. 3. Because the LW series switches and pilot lights require no studs for fastening the control unit to a P board, special preparation of operation panel is not needed. For details on one board mounting, contact IDE. Light Touch nd High eliability Load (g) Stroke " (3mm) Operating-force Snap Switching Mechanism LW series pushbutton (Momentary DPDT) LW series pushbutton (Momentary SPDT) 0.039" 0.078" 0.117" 0.156" 0.234" (1mm) (2mm) (3mm) (4mm) (6mm) Stroke TW series pushbutton (SPST-/SPST-N) US: (800) 262-IDE or (408) , anada (888) 317-IDE
Oiltight Switches & Pilot Devices
Oiltight Non-Illuminated ushbuttons (Sub-Assembled) Contact Block + Operator + Button = Completed Unit art Numbers: Operators Style art Number Momentary Maintained LW1B-M0 LW1B-A0 LW2B-M0 LW2B-A0 Mushroom
More informationMiniature Switches & Pilot Devices
ø16mm - 6 Series Miniature 6 Series Miniature Switches and Pilot Devices Key features of the 5/8 6 Series include: 5/8 (16mm) mounting holes ocking lever removable contact blocks Solder terminal or PB
More informationMW Series Control Units
IP waterproof and dust-proof enclosure Suitable for installation in harsh environment, such as construction machines Prevents entry of sand and dust. eliable operation under high operation load Solder/tab
More informationMiniature Switches & Pilot Devices
A8 Series Miniature Switches and Pilot Devices: 8mm Key features of the 21/64" (8mm) A8 series Switches and Pilot Devices include: 21/64" (8mm) round mounting hole Compact Design Saves Space Bright and
More informationSwitches & Pilot Devices
ø16mm - 6 Series Key features: 5/8 (16mm) mounting holes ocking lever removable contact blocks Solder terminal or PB terminal options Available assembled or as sub-components Worldwide approvals Incandescent
More informationSwitches & Pilot Devices
ø16mm - A6 Series A6 Series Miniature Switches and Pilot Devices: 16mm Key features: 16mm (/8 ) mounting hole ED illumination ompact design saves space Momentary, Maintained, Selectors, and E-Stops Gold-clad
More informationø22mm LW Series Control Units
ø22mm W Series ontrol Units ø22 W Series ontrol Units (Selection Guide) Function ategory ound Flush Square Flush Pushbutton ound Flush with Square Bezel Momentary/ ound Extended Square Extended W1B- 1
More informationSwitches & Pilot Devices
ø16mm - 6 Series 6 Series Miniature Switches and Pilot Devices Key features of the 5/8 6 Series include: 5/8 (16mm) mounting holes ocking lever removable contact blocks Solder terminal or PB terminal options
More informationA series Switches & Pilot Lights
A series Switches & Pilot ights ø16 ø12 ø10 ø8 A Series Selection Guide Series A6 Series Switches and Pilot ights Mounting Hole Size ø16 Model A6 AB6 AS6 AS6 (key) Disc tumbler key Shape Wave key Unit
More informationA Series. Miniature Control Units
TEIH-ATM Electronic Auf der Bült 10-12 D 41189 Mönchengladbach Tel. 02166 958545 Fax 02166 958547 email: atm@treichl.de internet: A Series Miniature ontrol Units A Series Miniature ontrol Units Series
More informationø8 A8 Series Miniature Control Units
A8 ø8 A8 Series Miniature Control Short 22-mm-long body miniature control unit series with LED illumination face and snap-action switching. Bright and clear LED illumination. All series have terminals
More informationSwitches & Pilot Devices
Key features: Two button sizes: ø29 and ø4mm ead-free, ohs compliant, (EU directive 22/95/EC) Depth behind the panel: Standard - only 27.9mm for 1 to 4 contacts Unibody - only 23.9mm for 1NC or 2NC IDEC
More informationø10 A1 Series Miniature Control Units
A1 ø10 A1 Series Miniature Control Short 22-mm-long body miniature control unit series with LED illumination face and snap-action switching. Bright and clear LED illumination. All series have terminals
More informationOiltight Switches & Pilot Devices
Oiltight Emergency Stop Stations Part Numbers: Emergency Stop Stations Description Contacts Plastic Bezel Metal Bezel Ø 40mm Pushlock Turn Reset 1NO-1NC HW1X-BV411-R* HW4X-BV411-R* 2NC HW1X-BV402-R* HW4X-BV402-R*
More informationBright illumination face and snap-action switching.
ø A2 Series ø10 A1 Series ø8 A8 Series A2 Series A1 Series A8 Series Bright illumination face and snap-action switching. See website for details on approvals and standards. Hole Size Model Function Degree
More informationø12 A2 Series Miniature Control Units
ø2 A2 Series Miniature Control Short 22-mm-long body miniature control unit series with bright LED illumination face and snap-action switching. Degree of protection: IP40 and IP5 (IEC 0529) All series
More informationOiltight Switches & Pilot Devices
Oiltight Switches & Pilot Devices HW Series 22mm IEC Style Global Pushbuttons Circuit Breakers Terminal Blocks Timers Relays & Sockets Display Lights Switches & Pilot Lights Key features include: Locking
More informationø22mm HW Series Control Units Control Units
mm HW Series Control Units Control Units HW Series Control Units (Selection Guide) Function Emergency Stop Switch (Unibody Type) Emergency Stop Switch (Separate Type) Pushlock Turn eset Category ø40mm
More informationSwitches & Pilot Devices
ømm - HW Series Key features: Locking lever removable contact blocks Finger-safe IP contacts Tamperproof construction All E-stops meet EN6947-5-5, and are compliant with SEMI S standards Worldwide approvals
More informationStyle Contact Type No. Button Color Code ø40mm Mushroom 1NC YW1B-V4E01R YW1B-V4E21R. Gasket ø40 YW1L-V4E11Q0R 2NC YW1L-V4E02Q➂R 6 (12V AC/DC)
Pushlock Pull/Turn eset Style Contact Type No. Button Color Code ø40mm Mushroom NC YWB-V4E0 2NC 3NC NO-NC NO-2NC 2NO-NC YWB-V4E02 YWB-V4E03 YWB-V4E YWB-V4E2 YWB-V4E2 ed only Dimensions Panel Thickness
More informationAP/UP Series Miniature Pilot Lights UZ Series Miniature Buzzer
AP/UP Series Miniature Pilot Lights UZ Series Miniature Buzzer Pilot Lights / Buzzer Selection Guide Series AP Series Miniature Pilot Lights AP6S Series Miniature Pilot Lights Mounting Hole Size ø6 ø2
More information[ Bezel size ] [ From panel front ] [ Shape ] [ Contact rating ] [ Action ] Unibody
and Series Suitable for a wide variety of office and factory aplications. Features IE s original mechanism for snap-action switching. The E lamp contains a current-limiting resistor and a diode for protection
More information22mm XW E-Stops. UL File #E68961 CCC No Specifications
XW Series 22mm XW E-Stops Key features: The depth behind the panel is only 48.7 mm for 1 to 4 contacts (with terminal cover) for illuminated and non-illuminated units. IDEC s original Safe break action
More informationXW Series Emergency Stop Switches
ø ø mm, 4-contact Emergency Stop Switch. Compact size only 37. mm deep behind the panel (screw terminal type 4 mm with terminal cover). eliable Safe break action. The depth behind the panel is only 37.
More informationSwitches & Pilot Devices
Selection Guide... 45 Miniature... 45 AP Series ø8-6mm... 45 A8 Series ø8mm... 456 ø6mm... 46 A E-Stops ø6mm... 46 B Series ø6mm... 468 6 Series ø6mm... 5 ømm... 55 W E-Stops ømm... 55 W Series ømm...
More information22mm XW E-Stops. IEC , EN , JIS C , UL508, UL991, NFPA79, CSA C22.2 No. 14, GB
ø22mm XW E-Stops Circuit Breakers Terminal Blocks ors Timers elays & Sockets Signaling ights 22mm XW E-Stops Key features: The depth behind the panel can be as little as 46.4 mm for 1 to 4 contacts (with
More informationOiltight Switches & Pilot Devices
ø0mm - TWTD Series iltight Switches & Pilot Devices TWTD Series Full Size NEMA Pushbuttons elays & Sockets Timers Terminal Blocks ircuit Breakers Display Lights Switches & Pilot Lights TWTD Series: Heavy
More informationXW Series E-Stops. Safety. Selection Guide ø22mm XW E-Stops
Safety Selection Guide... 288 ø22mm XW E-Stops... 289 www.idec.com/usa/estop XW Series E-Stops Overview Interlock Switches Enabling Switches Safety Control ight Curtains AS-Interface Safety at Work Table
More informationSwitches & Pilot Devices
Industrial utomation Catalog Section - U906 Switches & Pilot Devices HW Series Oiltight Switches & Pilot Devices Selection Guide Non-Illuminated Pushbuttons Emergency Stop Pushbuttons Emergency Stop Stations
More informationOiltight Switches & Pilot Devices
mm - Series Transfomer Contact Assemblies For use with Illuminated Pushbuttons. Style Contacts Part Number 12V AC with LED 24V AC with LED 48V AC with LED 12V AC with Incandescent 24V AC with Incandescent
More informationø25mm TWS Series Control Units
ø25mm TWS Series ontrol Units ø25 TWS Series ontrol Units (Selection Guide) Function ategory Flush Extended Pushbutton Extended with Half Shroud Momentary/ Extended with Full Shroud Mushroom Shape ABS1
More informationLW Silhouette Series. Illuminated Key Selector Switches Pushbuttons and Illuminated Pushbuttons with Round Guard. LW Silhouette Switches
W Silhouette Series Illuminated Key Selector Switches Pushbuttons and Illuminated Pushbuttons with ound Guard W Silhouette Switches W Silhouette Series Illuminated Key Selector Switches The two-way split
More informationø22mm HW Series Control Units
TREICHL-ATM Electronic Auf der Bült 10-12 D 41189 Mönchengladbach Tel. 02166 958545 Fax 02166 958547 email: atm@treichl.de internet: mm HW Series Control Units HW Series Control Units (Selection Guide)
More informationOiltight Switches & Pilot Devices
ø0mm - TWTD Series iltight Switches & Pilot Devices TWTD Series Full Size NEMA Pushbuttons elays & Sockets Timers Terminal Blocks ircuit Breakers Display Lights Switches & Pilot Lights TWTD Series: Heavy
More informationFull-Face, Split-Face, Dual-Color with built-in resistor. Oil and Water-Tight Version to IP65 available.
Miniature Lighted Pushbutton Switch KH Full-Face, Split-Face, Dual-olor with built-in resistor. Oil and Water-Tight Version to IP65 available. FEATUES mm (.67 ) mounting hole. Depth behind panel : Only
More informationXW Series E-Stops. Safety. ø22mm XW E-Stops Phone: Fax: Web: -
Safety ø22mm XW E-Stops... 277 XW Series E-Stops Overview Interlock Switches Enabling Switches Safety Control ight Curtains AS-Interface Safety at Work Phone: 8.894.412 - Fax: 888.723.4773 - Web: www.clrwtr.com
More informationIndicator body round for raised full face, black plastic, 22.5 mm mounting. Part No For complete switch also order
Series 14.5 mm 0.5 mm IP67 5 50 V INDITOR pushbutton keylock selector buzzer hoose one component from each of the coloured sections to assemble a complete switch. Product Profile Indicator The Series 14
More informationXA Series Emergency Stop Switches (w/removable Contact Block)
XA ø6 XA Series Emergency Stop Switches (w/removable Contact Block) The World s First ø6 mm, 4-contact Emergency Stop Switch. Compact size - only 7.9 mm deep behind the panel. Reliable Safe break action.
More informationIlluminated pushbutton, non-illuminated pushbutton, selector, key selector switches
ND Series: 16 dia. types (AEL, ABL, ASL, AKL) Illuminated pushbutton, non-illuminated pushbutton, selector, key selector switches Bright, clear illumination (ultra-high intensity LED used) Separate mounting
More informationSwitches & Pilot Devices
ømm - TW Series features: TW NEMA Switches with snap-on contacts Corrosion resistant octagonal chrome plated locking bezel Snap-on 0A contact blocks LED illumination Slow make, double break, contacts Modular
More informationNO NO NO. Standard Interlock Safety Switches HS6B. HS5E-K Key Locking Safety Interlock Switches
Standard Interlock Safety Switches HS6B HS5E-K Key Locking Safety Key features: Head removal detection circuitry. High-security pin tumbler key types are used. Sixteen types of key numbers are available,
More informationVH Super Miniature Lighted Pushbutton Switch. Only 10.6mm depth behind panel permits space saving on machinery.
Super Miniature Lighted Pushbutton Switch Only 10.6mm depth behind panel permits space saving on machinery. Flanged type for panel mounting and without flange type for PB available. FEATUES Depth behind
More informationDistinctive Characteristics
Distinctive haracteristics arefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Spot illumination available in single and bicolor
More informationø25 TWS Series Switches & Pilot Lights
ø25 TWS Series Switches & Pilot Lights General-purpose switches & pilot lights for various applications Heavy-duty type for high-level protection against harsh environment No terminal cover required (except
More informationGeneral Specifications
Series M eneral Specifications Miniature Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical apacity (Resistive Load)
More informationThe specified data apply only if actuators/signal indicators are combined with contact blocks and lamp sockets within the same product range.
General data QR control component range For a mounting hole diameter of.3 mm to IEC 60947 50V/10A max. Water-jet proof IP65 collar shapes The lamps of the pushbuttons can also be replaced from the front
More informationEmergency Stop Switches Selection Guide
Selection Guide New Concept Reverse Energy Structure Safe Break Action ø9mm Button E-BV3 (Solder, PC Board Terminal) Model Mark Page D-8 ø6m Mount Hole Non illuminated Detachable Block Pushlock Pull or
More informationA22/M22. Specifications. Specifications Common to All. Complete Assemblies
Complete Assemblies Specifications Common to All A22/M22 The Following Pages Provide Information Common To Each Model of The A22/M22 Pushbutton Switch H A22 H A22S/W H A22K H M22 Specifications J APPROVED
More informationUP Series Miniature Pilot Lights
Available in Various Sizes Five illumination colors: amber, green, red, white, yellow Various sizes and design. Available with a built-in current limiting resistor. Waterproof () types available for and.
More informationRelays & Sockets. RR Series Power Relays. Part Number Selection. Key features: Sockets IDEC (4332) USA & Canada
Key features: SPDT through PDT, 0 contacts Midget power type relays vailable in pin and blade terminal styles. Options include an indicator, check button for test operations and side flange. Series Power
More informationHW Series 22mm IEC Style Global Pushbuttons
ømm - HW Series Blocks Signaling Lights Key features: Locking lever removable contact blocks Finger-safe IP contacts as standard, other terminal styles available Tamperproof construction All E-stops meet
More informationRY2L Series Miniature Magnetic Latching Relays. E Release Time. 60N (0 6G); Maximum frequency 55Hz
Miniature Magnetic Latching Key features of the RY2L series include: Standard ice cube, 14-pin solder lug termination Operates by pulse input and maintains condition even during power failure Coils rated
More informationAP Series / UP Series Miniature Pilot Lights UZ Series Miniature Buzzer
AP Series / UP Series Miniature Pilot Lights UZ Series Miniature Buzzer Pilot Light / Buzzer Selection Guide Series AP Series Miniature Pilot Lights AP6S Series Miniature Pilot Lights Mounting Hole Size
More informationMC SERIES. Illuminated Control Units. Super LED or Incandescent Illumination Removable Contact Blocks
MC SERIES Illuminated Control Units Super LED or Incandescent Illumination Removable Contact Blocks MC SERIES ILLUMINATED CONTROL UNITS Super Bright LED or Incandescent Illumination New Rectangular- and
More information30mm Hazardous Location Switches:
30mm Hazardous Location Switches: EU2B Series PRODUCT DESCRIPTION Complying with UL and ATEX Directives for hazardous environments, new 30mm EU2B Hazardous Location Switches provide increased safety for
More informationSA1W: Water Detection Sensors
Courtesy of Steven Engineering, Inc. 230 Ryan Way, South San Francisco, CA, 94080-6370 ain Office: (650) 588-9200 Outside Local Area: (800) 258-9200 www.steveneng.com The SA1W is the fastest, most reliable
More informationINDUSTRIAL CONTROLS. Description. Products & features. Specifications. Illuminated or non-illuminated pushbutton switches.
INDUSTRIAL CONTROLS E A01 SERIES Panel cut-out.630" (16mm) Description Products & features Specifications Illuminated or non-illuminated pushbutton switches Indicators Rotary lever switches eylock switches
More information30mm Hazardous Location Switches:
30mm Hazardous Location Switches: EU2B Series PRODUCT DESCRIPTION Complying with UL and ATEX Directives for hazardous environments, new 30mm EU2B Hazardous Location Switches provide increased safety for
More informationRAFIX 22 QR. General data. Content
QR General data QR control component range For a mounting hole diameter of.3 mm to IEC 60947 50V/10A max. Water-jet proof IP65 collar shapes The lamps of the pushbuttons can also be replaced from the front
More informationEmergency Stop Switch A165E. Ordering Information. Mounting Aperture of 16 mm
Emergency Stop Switch Mounting Aperture of 16 mm Modular construction, easy installation Positive opening mechanism with minimum contact separation of 3 mm in accordance with EN60947-5-1, Conforms to EN418
More informationGeneral Specifications
eneral Specifications Miniature Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Electrical apacity (Resistive Load) Power Level
More informationA02 SERIES PUSHBUTTON SWITCHES, ILLUMINATED OR NON-ILLUMINATED Panel cut-out.866" (22mm) or 1.161" x.846" (29.5mm x 21.5mm)
PUSHBUTTON SWITCHES, ILLUMINATED OR NON-ILLUMINATED Panel cut-out.866" (22mm) or 1.161" x.846" (29.5mm x 21.5mm) E A pushbutton assembly requires: Screen + Lamp (if illuminated) + Operator + one or two
More informationRU Series Universal Relays
Full featured universal miniature relays Designed with environment taken into consideration Two terminal styles: plug-in and PCB mount Non-polarized LED indicator available on plug-in relays No internal
More informationLighted Pushbutton Switch
Lighted Pushbutton Switch General Purpose and Micro-Voltage/Current Load Switch Requires only 22 mm mounting depth All LEDs, lamps, legends and pushbutton units replaceable without tools Oil-resistant
More informationPressure Gauge Guide
ourtesy of Steven Engineering, Inc.-230 yan Way, South San Francisco, A 900-6370-Main Office: (650) 5-9200- Local Area: (00) 25-9200-www.stevenengineering.com Gauge for General Purpose With limit indicator
More informationGeneral Specifications
Standard Size Pushbuttons General Specifications Electrical apacity (Resistive Load) Power Level (silver): 3A @ 125V A or 3A @ 250V A or 3A @ 30V Logic Level (gold): 0.4VA maximum @ 28V A/ maximum (Applicable
More informationRelays. Industrial Automation Catalog Section - U906. Selection Guides. General Purpose Relays RU Series RR Series
Industrial Automation Catalog Section - U906 Relays Selection Guides General Purpose Relays RU Series RR Series For up-to-date information, or to request a full copy of this catalog, contact us at www.idec.com
More informationWe Make It Easy! 3. All of our switches are shipped complete, just as ordered. No incomplete or partial deliveries of subcomponents and accessories
We Make It Easy! 1. We assemble the parts for you saves you time and money. Includes LEDs and accessories 2. Easy to order all options and accessories displayed in easy-to-follow ordering table. No complicated
More informationA01 SERIES PUSHBUTTON SWITCHES, ILLUMINATED OR NON-ILLUMINATED Panel cut-out.630" (16mm)
PUSHBUTTON SWITCHES, ILLUMINATED OR NON-ILLUMINATED A pushbutton assembly requires: Screen + Lamp (if illuminated) + Operator + Switchblock To order, select desired model numbers from tables below. Example:
More informationEmergency Stop Switches
Emergency Stop Switches Emergency Stop Switches (Selection Guide) Series Emergency Stop Switch Name ø6mm X6 Series Pushlock Pull / Turn Reset (Unibody) ø6mm XA Series Pushlock Pull / Turn Reset (Unibody)
More informationA1-A01-A02-A03 series Industrial controls
A-A0-A0-A0 series Industrial controls Distinctive features The A0 and A0 series offer ranges of : - pushbutton switches, illuminated or not - indicators - or position keylock switches - or position rotary
More informationPushbuttons/Selectors/Pilot Lights AH25 General information
Pushbuttons/Selectors/Pilot Lights AH5 General information Features Oil and dust-proof construction Protection complies with IEC Standard IP65.Special seals keep out oil, water, dust, and chips. This gives
More information22mm Push Buttons and Switches
PUSH UTTONS/SWITCHES 22mm Push uttons and Switches Emergency Stops Selector Switches Lever Type Small Head 71.4 2 positions Large Head 3 positions unit: mm S2ER E3 R A D Size CONTACT LOCK * S2SR S 3 R
More informationOnly 35mm depth behind panel with built-in resistor
Lighted Pushbutton Switch R LED Only 5mm depth behind panel with built-in resistor Reliable Push-Feeling and valiable illumination Full-Face, Split-Face(,, ). FEATURES Depth behind panel : Only 5mm LED
More informationMicro Switch. NR SERIES ROCKER SWITCH 3-POSITION FLUSH-PANEL MOUNT, SCREW TERMINALS 1NR * Off 2-3* $24.58
Micro SEALED TOGGLE AND ROCKER SWITCHES A sealed switching chamber enables these toggle and rocker switches to comply with UL 508, paragraph 13.3 hosedown test. These switches survive where panels are
More informationPushbutton switches & indicators. Panel Sealed to IP65. Push on tab terminals 6A 250VAC AGENCY APPROVALS
Distinctive features and specifications A01_AX1607US Panel Sealed to IP65 Single pole to four pole changeover Custom engraving or film legends options Push on tab terminals 6A 250VAC PANEL CUT OUT ELECTRICAL
More informationGeneral Specifications
Series M Waterproof Miniature eneral Specifications Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical apacity (Resistive
More informationHS1E Series Full Size Interlock Switch with Locking Solenoid
HS1E Series HS1E Series Full Size Interlock Switch with Locking Solenoid HS1E Key features include: Basic unit and solenoid unit in one housing Plastic Housing: Light weight Ease of Wiring: All the terminal
More informationLighted PushButton Switch
Lighted PushButton Switch Cylindrical 8mm dia. Subminiature Series Featuring Short Mounting Depth Round, square and rectangular LED pushbutton units. types also available. Requires only 18mm mounting depth.
More informationø25mm TWS Series Switches & Pilot Lights
ø25mm TWS Series Switches & Pilot Lights ø25 TWS Series Selection Guide Function Pushbutton Category Flush Extended Extended with Full Shroud Mushroom Mushroom with Full Shroud Momentary/Maintained Shape
More informationA1-A01-A02-A03 series Industrial controls
A-A0-A0-A0 series Industrial controls Distinctive features The A0 and A0 series offer ranges of : - pushbutton switches, illuminated or not - indicators - or position keylock switches - or position rotary
More informationA1-A01-A02-A03 series
A1-A01-A02-A03 series Industrial controls Distinctive features The A01 and A02 series offer ranges of : - pushbutton switches, illuminated or not - indicators - 2 or 3 position keylock switches - 2 or
More informationSeries. Robust and attractive.
Series 82 Robust and attractive. www.eao.com Series 82 Robust and attractive. With Series 82, EAO offers the optimal pushbutton for vandal-resistant, stylish HMI controls used in harsh industrial environments,
More informationPushbutton switches & indicators. Panel Sealed to IP65. Push on tab terminals 6A 250VAC AGENCY APPROVALS
Distinctive features and specifications Panel Sealed to IP65 Single pole to four pole changeover Custom engraving or film legends options Push on tab terminals 6A 250VAC A01_AX1607USR1 ELECTRICAL SPECIFICATIONS
More informationSafety Products. Safety Products. HS5E Series. HS5E Series Miniature Solenoid Locking Switch
HS5E Series HS5E Series Miniature Solenoid Locking Switch HS5E Key features include: World s smallest 4 contact solenoid interlock switch. (35 40 46 mm.) Four contacts. Gold-plated contacts. Spring lock
More informationGeneral Specifications
Series HB Subminiature Pushbuttons General Specifications Electrical apacity (Resistive Load) Power Level (silver): 0.1A maximum @ 30V A/ Other Ratings ontact Resistance: 50 milliohms maximum Insulation
More informationNRA Series. Between main circuit terminals: 2,000V AC, 1 minute Between main circuit and auxiliary contact: 2,000V AC, 1 minute
RA Series RA Series RAS RA Key features of the RA series include: Available in 4 different styles Excellent overload and short circuit protection Small size and high-efficiency Life expectancy of over
More informationYB2 Panel Seal. New Square Actuator Option. Series YB2. Contact No Thin Flush Mount Pushbuttons. 24mm Square Panel Seal Pushbuttons
Contact No. 182 YB2 Panel eal Thin Flush Mount Pushbuttons New quare Actuator Option 2011-01-26 www.nkk.com 1 General pecifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V
More informationGeneral_technical_data Series
Indicator actuator 2 500 Hz: 5 g Pushbutton actuator Lens flat/level with front bezel: - Momentary max. 3 600/h - Maintain max. 1 800/h Lens flat/raised above front ring: - Momentary max. 3 600/h - Maintain
More informationEXCEL CELL ELECTRONIC CO., LTD. NO. A S P E C I F I C A T I O N Edition 2 Page 1
S P E C I F I C A T I O N Edition 2 Page 1 ECS - INDUSTRIAL CONTROL SWITCH SELECTOR 1. FEATURES Up to 5 different operations. Detachable contact block for easy installation and removal. It can meet variety
More informationD2SW-P. Sealed Subminiature Basic Switch. Ordering Information D2SW-P
Sealed Subminiature Basic Switch Sealed Basic Switch with Simplified Construction, Mounting Compatible with SS and D2SW Series. Sealing by using rubber packing means the switch can be used in dust-proof
More informationHS2B N B - R. Door Interlock Switches. HS2B Series. Full Size Interlock Switch. Part Number. HS2B features: Part Number Key.
HSB Series HSB Series Full Size Interlock Switch HSB features: Body Direct Opening Action: If the door is forced open, the contacts are disconnected even if they are welded or stuck Available with or without
More informationDoor Interlock Switches
HSE Series HSE Series Full Size Locking Switches Overview X Series E-Stops HSE features: Basic unit and solenoid unit in one housing Plastic Housing: Light weight Ease of Wiring: All the terminal screws
More informationNon-illuminated Push Buttons
Non-illuminated Push Buttons 3 Accessories for push buttons Lockout attachment Contact block kits Lens kits Wobblestick kit Push Button Cap Interchangeable, snap-in design Protective caps 9 colors: red,
More informationDistinctive Characteristics
Distinctive Characteristics Various cap styles and colors to meet differing application needs. Bright, full face illumination to distinctively indicate status. Rear panel threaded mounting or snap-in mounter
More informationLUMOTAST 25 selector switch 1-28 LUMOTAST 25 selector switch, Click quick-assembly feature 1-29 LUMOTAST 25 selector switch, ring nut fixing 1-29
General data TAST pushbutton range Illuminable pushbuttons and signal lamps. Please order lamps/leds separately. Mounting hole diameter: 6.2 mm 42 V/00 ma max. Water-jet proof IP65 Low profile Lamp socket
More informationHS1B R - R. Door Interlock Switches. HS1B Series. HS1B Series Full Size Interlock Switch. Part Number. HS1B features: Part Number Key.
HSB Series HSB Series Full Size Interlock Switch HSB features: Body Rugged aluminum die-cast housing Direct Opening Action: If the door is forced open, the contacts are disconnected even if they are welded
More informationHMI Components. Series. Indicator Illuminated pushbutton Mushroom-head pushbutton Key lock switch
Edition 10/2016 HMI Components Series Characteristics The compact Series is especially suited for: Flush design The large rectangular design (24x36mm) features a large illuminated area. Functions The Series
More informationDistinctive Characteristics
Distinctive Characteristics Full face or spot illumination with incandescent lamps or multi-element LEDs, with or without resistors. Choice of super bright LEDs in white, green, and blue as well as bright
More informationSwitches & Pilot Devices
ø0mm - TWTD Series TWTD Series Full Size NEMA Pushbuttons elays & Sockets Timers ircuit Breakers ontactors Terminal Blocks Signaling ights TWTD Series: Heavy duty switches built to last features: Variety
More information