NRA Series. Between main circuit terminals: 2,000V AC, 1 minute Between main circuit and auxiliary contact: 2,000V AC, 1 minute

Transcription

1 RA Series RA Series RAS RA Key features of the RA series include: Available in 4 different styles Excellent overload and short circuit protection Small size and high-efficiency Life expectancy of over 0,000 operations UL077 recognized Supplementary Protectors VDE certified to E60934 File o. E68029 license #638 RAR Rocker RAR Illuminated Rocker (neon lamp) Specifications Protection Method Internal ircuit umber of Poles Rated Voltage Rated Tripping urrents Rated Interrupting apacity Auxiliary ontact Alarm ontact Electromagnetic tripping Series current trip RAS and RA:, 2, 3 RAR: 250V A, 50/60Hz, 65V D. RAR is not SA certified. 2. ot suitable for branch circuit protection. 0.30A, 0.50A, 0.75A A, 2A, 3A, 5A, 7.5A, 0A, 5A, 20A, 25A, 30A 250V A, 50/60Hz,,000A 65V D,,000A SPDT microswitch 250V A, 5A (resistive load) 50V D, A (resistive load) Reference Temperature 25 Operating Temperature 40 to +85 (avoid freezing) Insulation Resistance MΩ minute (measured with 500V megger) Dielectric Strength Between main circuit terminals: 2,000V A, minute Between main circuit and auxiliary contact: 2,000V A, minute Vibration Resistance (approximately 0G) (0 to Hz) Shock Resistance,000 (approximately G) Life Expectancy Minimum 0,000 cycles (at 6 operations per minute) Termination Illumination Voltage (RAR illuminated units) Main terminal: Quick-connect receptacle 0.250" (accepts M3.5 screw terminal adapter) Auxiliary contact, alarm contact: Quick-connect receptacle 0.080" eon: 20, 240V A, 50/60Hz USA: (800) 262-IDE or (408) , anada (888) 37-IDE -3

2 RA Series Part umbering Guide RA series part numbers are composed of up to 8 part number codes. When ordering an RA series part, select one code from each category. Example: RAR -F - 30A -AA -3 RAR F 30A AA 3 ➀ Model ➁ Poles ➂ Internal ircuit ➃ Auxiliary and Alarm ontacts 5 Inertia Delay ➅ Rated urrent ➆ Time Delay 8 Pilot urve Light * Part umber odes: RA Series Description Part umber ode Remarks ➀ Model ➁ o. of Poles Toggle (round cutout) Toggle (rectangular cutout) Rocker RAS RA RAR -pole RAR available in -pole only. 2-pole 2 All multi-pole circuit breakers are simultaneous throw/simultaneous break. 3-pole 3 All levers are mechanically interlocked. ➂ Internal ircuit Series current trip ➃ Auxiliary and Alarm ontacts Without 00 With auxiliary contact Auxiliary contact switches change state with lever and/or overload condition With alarm contact 2 Alarm contact switches change state only with overload condition 5 Inertia Delay ➅ Rated urrent ➆ Time Delay urve 8 Pilot Light* Without inertia delay With inertia delay Rated current (current trip) D curves A curves With neon light 20V A (50/60Hz) With neon light 240V A (50/60Hz) 2 Blank F 0.30A, 0.50A, 0.75A, A, 2A, 3A, 5A, 7.5A, 0A, 5A, 20A, 25A, 30A AD, MD AA, BA,MA All current ratings must be listed in amps (A). Example conversion: 300mA = 0.30A. For time delay curves, see page -7. * Applicable to illuminated RAR only.. For RA series accessories, see page For RA series time delay curves, see page For RA series dimensions, see page ot suitable for branch circuit protection. 5. UL recognized, applicable standard: UL077, Supplementary Protectors USA: (800) 262-IDE or (408) , anada (888) 37-IDE

3 RA Series Information About Time Delay urve Descriptions Time Delay urve AD, AA BA MD, MA With Inertia Delay RA Application ommon curves used in molded-case circuit breakers. Response to overcurrent is quite fast. Suited for protection of semiconductor circuits with very little overload tolerance. If overcurrents are expected to flow, fuses may be required according to the circuit characteristics. Suited for motor loads that draw high inrush currents lasting a considerable length of time. Designed not to trip on 20 times the rated current (peak value) for a duration of 8ms. Suited for transformer and lamp loads that draw steep inrush currents. Inertia Delay Descriptions ircuit breakers equipped with inertia delay do not respond to high inrush currents such as those produced by transformer, lamp, or motor loads, but perform the specified interruption on the rated overcurrents. Specify inertia delay by inserting an F in the part number as shown in Part umber Guide on previous page. 6,000 4,000 2,000 0,000 8,000 6,000 4,000 Pulse Width Pulse Peak urrent (duration) 2, Pulse Width (ms). = Pulse Peak urrent x % Protector Rated urrent 2. Based on sinusoidal or parabolic pulse profile. otes Multi-Pole Multi-pole types such as 2- or 3-pole should be assembled by IDE. Because of their characteristics, -pole breakers cannot be combined to provide multi-pole units. Auxiliary and Alarm ontacts Multi-pole units can incorporate auxiliary and alarm contacts. Auxiliary and alarm contacts will not work with IDE s DI rail adapters. USA: (800) 262-IDE or (408) , anada (888) 37-IDE -5

4 RA Series Accessories Part umbers: RA Series Accessories Description Appearance Part o. Remarks olor aps (RAS only) Red Blue Yellow Ø 0.62" (5.8mm) R5R R5S R5Y olored ap Panel White R5H olored caps fit onto RAS circuit breakers for color coding circuits and improving the appearance of the panel. Terminal Socket MS- For connection with auxiliary or alarm contact terminals. Screw Terminal Adapter ( pair) RT For use on main terminals only. Includes M3.5 clamp screw. For dimensions see page -0. Part umbers: RA Mounting Accessories Description Appearance For Model Panel Mount Flush Plate 0.936" (24mm).89" (48.5mm) 2.65" (68mm) 2.46" (63mm) RA RAR o. of Poles -pole Part o. R3 RA 2-pole R32 RA 3-pole R33 Remarks Use of a flush plate makes snap-in mount possible for RA, and RAR circuit breakers (tightening screws not necessary). Multiple units can mount in a single panel cut-out. DI Rail Plug-in Base Surface Mount Plug-in Base Mounting lip DI Rail 0.757" (9.4mm) -Pole.50" (38.5mm) 2-Pole 2.26" (58mm) 3-Pole Hold-Down Spring RAS RA -pole 2-pole 3-pole R2 R22 R23 RAR -pole R2 -pole US RAS RA 2-pole US2 3-pole US3 RAR -pole US.Furnished with a holddown spring. 2.Applicable only for series trip units up to 20 amps. 3.ot applicable for RAR lighted series. 4.ot for use with circuit breakers incorporating auxiliary or alarm contacts. For dimensions of RA series accessories and panel cut-out layouts, see drawings starting on page USA: (800) 262-IDE or (408) , anada (888) 37-IDE

5 RA Series Internal ircuits and Terminal Arrangements: RAS and RA Series Series urrent Trip LIE Series urrent Trip with Auxiliary ontacts LIE Series urrent Trip with Alarm ontacts LIE O O Internal ircuits and Terminal Arrangements: RAR Series Series urrent Trip Series urrent Trip with Auxiliary ontacts Series urrent Trip with Alarm ontacts Pilot Lights (RAR only) Lead Wire (+) ( ) LIE LIE Lead Wire A Lead Wire B O LIE Lead Wire A Lead Wire B O Pilot Light A B eon (20V A) White White eon (240V A) Black Black Dashed lines represent RAR illuminated rocker units. Lead wires for neon pilot light/led are colorcoded as shown above. Time Delay urves (numerical equivalent) Overcurrent Time Delay haracteristics in Seconds (at 25 ) urve % 25% 50% 200% 400% 600% 800% 0% AD o trip MD o trip AA o trip BA o trip D A (50/60Hz) MA o trip All values above are in seconds. 2. Data in this table is equivalent to information presented in following time delay curves. USA: (800) 262-IDE or (408) , anada (888) 37-IDE -7

6 RA Series D Time Delay urves,000,000 AD Delay urve at 77 F (25 ) MD Delay urve at 77 F (25 ) Time in Seconds 0 0. Time in Seconds , , A (50/60Hz) Time Delay urves,000,000 AA Delay urve at 77 F (25 ) BA Delay urve at 77 F (25 ) Time in Seconds 0 0. Time in Seconds ,000, ,000 MA Delay urve at 77 F (25 ) Time in Seconds , USA: (800) 262-IDE or (408) , anada (888) 37-IDE

7 RA Series Resistance and Impedance haracteristics oil Data for Series urrent Trip at 25 Rated A Impedance D Resistance urrent (50/60Hz) urves AA, BA, urves AD, MD MA 0.30A 9.67Ω 9.82Ω 0.50A 3.24Ω 3.36Ω 0.75A.45Ω.49Ω A 0.90Ω 0.92Ω 2A 0.2Ω 0.2Ω 3A 0.09Ω 0.092Ω 5A 0.036Ω 0.036Ω 7.5A 0.07Ω 0.08Ω 0A 0.02Ω 0.02Ω 5A Ω Ω 20A Ω Ω 25A Ω Ω 30A Ω 0.004Ω Tolerance ±25% (up to 20A), ±50% (25A and over). Rated urrent (A) Rated urrent (A) oil Resistance at 25 0 urves AD, MD oil Resistance (Ω) 0 urves AA, BA, MA 0. Voltage Drop Due to Resistance or Impedance The internal resistance or impedance of a circuit breaker tends to be larger for a smaller rated current. Therefore, when circuit breakers with a small rated current are used, voltage drop should be taken into consideration. Internal resistance also varies with time delay curves, even at the same rated current. This should also be considered during installation Impedance (Ω) Time Delay urve and Ambient Temperature Since RA series circuit breakers employ an electromagnetic tripping system, the rated current (trip current) is not affected by the ambient temperature, but the time delay varies with the oil viscosity in the tube. Lower oil viscosity at higher temperatures results in shorter delay; whereas at lower temperatures, the delay will be prolonged. The time delay curves, shown starting on page - 7, are at 25. Time delay curves can be corrected. Rated urrent (A) Temperature orrection urves Ambient Temperature ( ) urves AD, AA, BA (on 25% rated current) 90 USA: (800) 262-IDE or (408) , anada (888) 37-IDE -9

8 RA Series Dimensions 0.250" Tab Terminal 0.0" Tab Terminal RAS 2.03" (52mm).65" (42.2mm).20" (30.8mm).20" (30.8mm) 60.56" (40mm) -pole: 2-pole:.49" (38.2mm) 3-pole: 2.23" (57.3mm) 0.683" (7.5mm).56" (40mm).93" (49.5mm) 2." (54mm) 0.250" Tab Terminal 0.0" Tab Terminal RA 2.03" (52mm).65"(42.2mm).23"(3.5mm).20" (30.8mm) 60.56" (40mm) -pole: 2-pole:.49" (38.2mm) 3-pole: 2.23" (57.3mm) 0.644" (6.5mm).60" (4mm).97" (50.5mm) 2." (54mm) 0.250" Tab Terminal 0.0" Tab Terminal RAR 2.03" (52mm).65" (42.2mm).23" (3.5mm) O OFF LED 0.78" (20mm).56" (40mm) 0.47" (0.7mm) 2.8" (56mm) 2.55" (65.5mm) 2.69" (69mm) -0 USA: (800) 262-IDE or (408) , anada (888) 37-IDE

9 RA Series Panel ut-outs Installation Angle: ircuit breakers are designed to operate on a vertical surface. The mounting angle should not exceed a vertical plane by more than 0. RA Series RAS Ø0.58" (4mm) Mounting Holes RAR, RA Ø0.56" (4mm) Mounting Holes 0.630" (6mm).05" (26.7mm).66" (42.2mm) 0.20" (5.mm).26" (32mm).66" (42.2mm) -Pole 2-Pole 3-Pole.49" (38.2mm) 2.23" (57.3mm) R3, R32, R33 Panel Mount Flush Plate 2.09" (53.5mm).5" (38.7mm) 0.764" (9.6mm) 2.25"(57.8mm) Maximum Mounting Distance Model A B Schematics in Inches (mm) RAS 3.02" (77.5mm) 3.57" (9.5mm) RA 3.02" (77.5mm) 3.57" (9.5mm) RAR 3.38" (86.7mm) 3.93" (.7mm) Mounting to Panel Surface Mounting to DI Rail USA: (800) 262-IDE or (408) , anada (888) 37-IDE -

10 RA Series Accessory Dimensions RT: Screw Terminal Adapter (for use with RA Series).For use on main terminals only. 2.Includes M3.5 clamp screw. BD0 Aluminum DI Rail Length in Inches (mm) F A B.4" (35mm).4" (29mm) 0.78" (23mm) G H K A B D D E F.2" (3mm) 0.4" (0.5mm) 0." (3mm) G 2" (5mm) Overall length 39.4" (0mm) H H K 0.47" (2mm) 0.6" (4mm) -2 USA: (800) 262-IDE or (408) , anada (888) 37-IDE

11 Instructions Instructions: All Series General IDE s circuit breakers have been developed for the protection of electrical circuits and small-sized electrical equipment and provide excellent protection against overloads and short-circuits. Additionally, IDE s circuit breakers are designed to suit specific needs. Each series offers unique circuit protection characteristics and a choice of actuator styles. IDE s ircuit Breaker Features Various models are available with different internal circuits, tripping characteristics, and rated currents - to 3- multi-pole Inertia delay Auxiliary contacts and alarm contacts The electromagnetic tripping system is not affected by ambient temperature Safe trip-free mechanism Vibration- and impact-resistant design When using accessories such as plug-in bases, flush plates, and colored caps, a variety of mounting styles is possible such as DI rail mounting, snap mounting into panel cut-outs, and color-coded arrangement on the panel Mounting Instructions: Installation Angle Designed to be mounted on a vertical surface, the circuit breakers should be mounted on a surface within 0 of the vertical plane. If the circuit breaker is mounted on a horizontal surface or at any angle other than the specified angle, its characteristics will be changed. Multi-Pole Assemble Multi-pole types such as 2- or 3-pole should be assembled by IDE. Because of their characteristics, -pole breakers cannot be combined to produce multi-pole units. Applications The IDE RA circuit breaker series features superior overload and short-circuit protection. Many combinations of protection mechanisms and internal circuit connections enable wide applications. Precision measuring instruments: electronic counters, projection instruments, oscilloscopes, industrial instrumentation, and analytic devices Electronic communication devices: facsimile machines, computers, recorders Industrial machinery: printers, elevators, cranes hemical and food industry machines: vacuum devices, wrappers, centrifuges, agitators Machine tools: mill grinders, drills, presses Business machines: automatic vendors, medical equipment, beauty salon equipment, entertainment games Other: office equipment, air-conditioners, conveyor belts, and many more How the Breaker Operates IDE s hydraulic magnetic circuit breakers operate like a solenoid coil. The coil unit consists of an oil-filled tube with a metal core at one end and a pole piece and armature at the opposite end with a spring in between. When a current load passes through the coil winding, it creates a magnetic field. As long as the current load is either at or below the nominal rating of the breaker, the metal core will remain stationary. If the current load increases beyond the nominal rating, the strength of the magnetic field causes the core to move toward the pole-end of the tube. The oil viscosity regulates the core s movement through the tube, thereby regulating the time delay. As the percentage of current load increases, the required trip time of the breaker decreases and vice versa. When the current reaches the overload rating, the metal core will meet the pole piece at the opposite end of the tube. At this point, the armature is attracted to the same pole piece, tripping the breaker. In case of sudden short circuit, the magnetic field created will instantly trip the breaker. Internal ircuits Overview Description ircuit Example Load Series Trip This is the most common circuit breaker, providing excellent overload and short circuit protection. It can also be used as an O/OFF switch. Load B Load B Load A Load A Series Trip with Auxiliary ontact Since the auxiliary contact operation is interlocked with the O/OFF of the main contactor, circuit breaker operation can be monitored by a lamp or buzzer. This circuit breaker can also be used to control auxiliary circuits up to 250V A/5A (resistive load). Series Trip with Alarm ontact Since the alarm contact is electrically independent of the main contactor, but actuates when the protective element operates. The alarm can be used with a lamp or buzzer to monitor trip operations, and can also be used for controlling alarm circuits. The contact rating is 250V A/5A (resistive load). USA: (800) 262-IDE or (408) , anada (888) 37-IDE -29