Distinctive Characteristics

Transcription

1 Distinctive haracteristics arefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Spot illumination available in single and bicolor LEDs. hoice of super bright LEDs in white, green, and blue in addition to standard or bright red, amber, and green LEDs. Stainless steel clips provide secure mounting with a wide range of panel thicknesses. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Snap-action contact mechanism gives long electrical life and sensitivity of actuation. ombination solder lug and.110 quick connect terminals are epoxy sealed to prevent entry of flux, dust, and other contaminants. Panel sealed model meets IP65 of IE60529 specifications (similar to NEMA 4 & 13). ompact switch design minimizes behind panel depth. Nonilluminated models available and shown in the Pushbutton section. Matching indicators available and shown at the end of Section M. Actual Size

2 General Specifications Electrical apacity (Resistive Load) Power Level (silver): 125V A or 250V A or 30V D Logic Level (gold): 0.4VA 28V A/D maximum (Applicable Range 0.1mA ~ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings ontact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold Insulation Resistance: 200 megohms 500V D Dielectric Strength: 1,000V A minimum between contacts for 1 minute minimum; 1,500V A minimum between contacts & case for 1 minute minimum Mechanical Life: 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit Electrical Life: 100,000 operations minimum Nominal Operating Force: 4.41N ontact Timing: Nonshorting (break-before-make) Travel: Momentary: Pretravel.059 (1.5mm); Overtravel.059 (1.5mm); Total Travel.118 (3.0mm) Maintained: Pretravel.087 (2.2mm); Overtravel.031 (0.8mm); Total Travel.118 (3.0mm) Materials & Finishes Housing: Snap-in Frame: Movable ontact: Stationary ontacts: Base: Switch Terminals: Lamp Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Sealing: Installation ap Installation Force: Quick onnect Force: Soldering Time & Temperature: Standards & ertifications Flammability Standards: UL & -UL Recognized: R SA ertified: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Brass with silver plating 25 through +50 ( 13 F through +122 F) Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0 (32 F) 90 ~ 95% humidity for (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Not available for snap-in; see next section for panel seal. 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. UL94V-0 housing & base All models recognized at 125V or 250V A or 28V A/D maximum; UL File No. WOYR2.E44145; add /U to end of part number to order UL mark on switch. -UL File No. WOYR8.E44145; add /-UL to end of part number to order -UL mark on switch. All models certified at 125V or 250V A or 28V A/D maximum; SA File Nos ; add / to end of part number to order SA mark on switch.

3 TYPIAL SWITH ORDERING EXAMPLE LB 1 5 S K W J POLES SHAPES HOUSING LAMPS AP TYPES & OLORS 1 SPDT 2 DPDT S R K G Black Gray Incandescent Lamp used with Solid ap 05 5-volt volt BJ J Solid ap: Lens/Filter olors White/lear Red/lear EJ Yellow/lear IRUITS 5 () ( ) = Momentary 6 Alternate Action with Latchdown W01 G01 TATS & TERMINALS Silver ontacts Rated 125/250V A Solder Lug/Quick onnect Terminals Gold ontacts Rated 28V A/D Solder Lug/Quick onnect Terminals Incandescent or Neon used w/ Insert ap volt Neon 05 5-volt Incandescent FJ GJ J Green/lear Blue/lear Insert ap: Lens/Filter olors lear/white lear/red DESRIPTI FOR TYPIAL ORDERING EXAMPLE LB15SKW J volt Incandescent JE * JF * JG lear/yellow lear/green lear/blue * JF & JG not suitable with neon. Bright LED used with LED ap LED ap: Lens/Diffuser olors olors Resistor lear/white Red, 12-volt, Bright LED with Resistor SPDT -() ircuit lear ap with Red Diffuser Shape 5 5D 5F Red Amber Green No ode No Resistor 05 5-volt volt volt J JD JF lear/red lear/amber lear/green Silver ontacts Rated 125/250V A; Solder Lug/Quick onnect Terminals Black Housing Super Bright LED used with LED ap 6B White LED ap: Lens/Diffuser olors lear/white 6F Green 6G Blue IMPORTANT: Switches are supplied without UL, -UL & SA markings unless specified. Specific models & ratings noted on General Specifications page. 1 1D 1F F LED in Spot Illuminated ap Red Single olor Amber Single olor Green Single olor Red/Green Bicolor A B F Spot Illuminated ap olors Black White Red Green Available in square and round only. NKK Switches sales@nkkswitches.com Phone (480) Fax (480) NKK Switches sales@nkkswitches.com Phone (480) Fax (480)

4 Pole Model POLES & IRUITS Plunger Position ( ) = Momentary onnected Terminals Throw & Switch/Lamp Schematics Normal Down Normal Down Notes: Switch is marked with N,, OM, L+, L. Lamp circuit is isolated and requires external power source. SP LB15 *LB16 () SPDT 1 OM 3 N 2 (-) L DP LB25 *LB26 () DPDT 1 OM 4 OM 3 N 2 6 N 5 (-) L * When in latchdown position for the alternate circuit, cap position is.039 (1.0mm) above the built-in bezel. SHAPES & PANEL UTOUTS S.622 (15.8mm).854 (21.7mm) R.622 x.866 (15.8mm x 22.0mm) (22.0) Dia.866 (16.2).638 (11.5).453 (16.2) Sq.638 utout for 1 switch:.638 x.638 (16.2mm x 16.2mm) utout for 1 switch with barriers:.638 x.815 (16.2mm x 20.7mm) (1.5) R.059 Panel Thickness for Switches & Barriers:.039 ~.157 (1.0 ~ 4.0mm) Panel Thickness for Protective Guards & Splash overs:.039 ~.138 (1.0 ~ 3.5mm) HOUSING (22.4).882 utout for 1 switch:.638 x.882 (16.2mm x 22.4mm) utout for 1 switch with barriers:.638 x (16.2mm x 26.9mm) Housing olors Available: K Black G Gray TAT MATERIALS, RATINGS & TERMINALS W01 G01 Silver ontacts Gold ontacts Power Level 125V A & 250V A Logic Level 0.4VA 28V A/D max. omplete explanation of operating range in Supplement section. Solder Lug/Quick onnect Optional PB adaptors AT711 & AT712 available; illustrated in Optional Accessories immediately following Typical Switch Dimensions. Epoxy Seal (7.5).295 (2.0).079 (2.8).110 (1.2).047 Thk = (0.5).020 INANDESENT & NE LAMP ODES & SPEIFIATIS AT607 & AT607N T-1 Bi-pin AT607 Incandescent 5-volt or 12-volt; AT607N Neon 110-volt Voltage V 5V A 12V A 110V A urrent I 115mA 60mA 1.5mA Endurance Avg. Hours 7,000 10,000 Ambient Temp. Range ~ * The electrical specifications shown are determined at a basic temperature of 25. Lamp circuit is isolated and requires external power source. * Recommended Resistors for Neon: 33K ohms for 110V A; 100K ohms for 220V A

5 LED OLORS & SPEIFIATIS The electrical specifications shown are determined at a basic temperature of 25. LED circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. AT635 LEDs are colored in OFF state. AT627 with Resistor (+) (-) T Bi-pin T-1 Bi-pin olor odes Red Amber Green Forward Peak urrent I FM 30mA 30mA 30mA ontinuous Forward urrent I F 20mA 20mA 20mA Forward Voltage V F 1.9V 2.0V 2.1V Reverse Peak Voltage V RM 5V 5V 5V urrent Reduction Rate Above 25 I F 0.42mA/ Ambient Temperature Range olor odes: Bright LED without Resistor Red Amber Green 5 5D 5F Bright LED with Resistor No ode 25 ~ +50 Resistor odes No Resistor Forward Peak urrent I FM ontinuous Forward urrent I F 52mA 26mA 13mA Forward Voltage V F 5V 12V 24V Reverse Peak Voltage V RM 4V 8V 16V urrent Reduction Rate Above 25 I F 0.50mA/ Ambient Temperature Range Red Amber Green 5 5D 5F ~ +50 AT627 5-volt 4-element with Resistor (+) (-) AT volt 4-element with Resistor (+) (-) AT volt 4-element with Resistor (+) (-) Super Bright Single Element LED AT625G Blue AT631B White AT632F Green (+) (-) T-1 Bi-pin Attention Electrostatic Sensitive Devices olor White Green Blue Forward Peak urrent I FM 30mA 30mA 30mA ontinuous Forward urrent I F 20mA 20mA 20mA Forward Voltage V F 3.6V 3.5V 3.6V Reverse Peak Voltage V RM 5V 5V 5V urrent Reduction Rate Above 25 I F 0.50mA/ Ambient Temperature Range 6B 6F 25 ~ +50 6G

6 AP TYPES & OLOR OMBINATIS olor odes: B White Red D Amber E Yellow F Green G Blue J lear Solid ap for Incandescent Lamp Lens/Filter olors Available: BJ J FJ GJ AT476 (3.5).138 (6.5).256 AT4012 (4.5).177 (5.5).217 (13.2) AT4026 (19.4).764 (5.0).197 (6.0).236 Translucent olored Lens Transparent lear Filter EJ Material: Polycarbonate Lamp AT607 Insert ap for Incandescent or Neon Lamp Lens/Filter olors Available: AT477 AT4013 AT4027 J JF JG (3.5).138 (6.5).256 (4.5).177 (5.5).217 (13.2) (19.4).764 (5.0).197 (6.0).236 Transparent lear Lens Translucent olored Filter JE JF and JG not suitable with neon lamp. Material: Polycarbonate Lamp AT607 or 607N ap for Bright LED without Resistor Lens/Diffuser olors Available: AT4176 AT4178 AT4177 J JD (3.5).138 (6.5).256 (4.5).177 (5.5).217 Transparent lear Lens Translucent olored Diffuser JF Material: Polycarbonate Bright LED AT635 ap for Bright LED with Resistor Lens/Diffuser olors Available: AT4162 AT4164 AT4163 (3.5).138 (4.5).177 (13.2) (19.4).764 Transparent lear Lens J JD (6.5).256 ( (5.0).197 (6.0).236 Translucent olored Diffuser JF Material: Polycarbonate Bright LED AT627

7 AP TYPES & OLOR OMBINATIS olor odes: A Black B White Red D Amber F Green J lear ap for Super Bright LEDs Material: Polycarbonate lear Lens White Diffuser AT4129 (3.5).138 (6.5).256 AT4128 (4.5).177 (5.5).217 (13.2) AT4130 (19.4).764 (5.0).197 (6.0).236 Transparent lear Lens Translucent White Diffuser Material: Polycarbonate LEDs AT625 AT631 AT632 Spot Illuminated ap with LED The electrical specifications shown are determined at a basic temperature of 25. LED circuit is isolated and requires external power source. Single color LEDs are colored in OFF state; bicolor LEDs are translucent white in OFF state. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. LED factory assembled in Spot Illuminated aps Not Available Separately Single olor LED with 1 Element Single olor Bicolor Red Amber Green Red/Green Forward Peak urrent I FM 10mA 30mA 30mA 30/25mA ontinuous Forward urrent I F 8mA 24mA 24mA 20mA Forward Voltage V F 1.9V 2.0V 2.1V 2.0/2.2V Reverse Peak Voltage V RM 5V 5V 5V urrent Reduction Rate Above 25 I F 0.13mA/ 0.40mA/ 0.40mA/ 0.43/0.38mA/ Ambient Temperature Range LED Specifications Bicolor LED with 2 Elements (+) (-) (+) (-) 1 1D 1F 25 ~ +50 F ap olors Available: AT480 AT4016 A B (4.0).157 (2.0).079 (5.0).197 (3.5).138 (5.0).197 (4.5).177 (5.5).217 ap with Window F (6.5).256 Material: Polycarbonate (2.0).079 (6.0).236 Factory Assembled LED; Not Available Separately When ordering spot illuminated cap separately, LED color must be specified. Examples: AT480A (red LED, black cap); AT4016FB (red/green bicolored LED, white cap)

8 TYPIAL SWITH DIMENSIS Single & Double Pole (1.8).071 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ.020 N (15.8) Sq.622 OM 1 L (-) 4 (17.8) Sq.701 (1.0).039 (3.2).126 (21.5).846 Latchdown Position (7.5).295 (2.8) Typ.110 (5.08) Typ LB15SKW01-12-J Single pole models do not have terminals 4, 5, & 6. Single & Double Pole (1.8).071 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ.020 N OM L (-) 4 (15.8) Sq.622 (21.7) Dia.854 (23.7) Dia.933 (1.0).039 (3.2).126 (21.5).846 Latchdown Position (7.5).295 (2.8) Typ.110 (5.08) Typ LB16KW01-12-J Single pole models do not have terminals 4, 5, & 6. Single & Double Pole (1.8).071 (1.2) x (2.0) Typ.047 x.079 (13.2) (17.8).701 (0.5) Typ.020 N OM L (-) 4 (15.8).622 (19.4).764 (24.0).945 (1.0).039 (3.2).126 (22.5).886 Latchdown Position (7.5).295 (5.08) Typ (22.0).866 (2.8) Typ.110 LB26RGW01-12-J Single pole models do not have terminals 4, 5, & 6. OPTIAL AESSORIES N N (5.08) PB Adaptors AT711 Single Pole Straight P Terminals AT712 Double Pole Straight P Terminals (0.3) Typ.012 (0.3) Typ.012 N N (5.08) Typ (0.5).020 (15.0) (4.0) (0.74) Typ.029 OM L (-) OM (5.08) (15.8) Sq.622 (1.0) Dia Typ.039 (0.5).020 (15.0) (4.0) (0.74) Typ.029 OM L (-) OM (5.08) (15.8) Sq.622 (1.0) Dia Typ.039 Note: Order adaptors separately.

9 OPTIAL AESSORIES Barriers AT497 End End Position AT498 enter (4.3) Typ.169 (5.2).205 (23.5).925 (19.2).756 utouts for More Than 1 Switch A (20.0).787 (15.0).591 (16.2).638 enter Position Material: Polyamide (1.19).047 (1.19).047 (19.2).756 A =.752 (19.1mm) x Number of Switches (1.3mm) A =.996 (25.3mm) x Number of Switches (1.3mm) Splash overs AT499 Protective Guard Opens 90 loses manually (21.0).827 (10.0).394 (17.0).669 (20.0).787 ap Height When Assembled (8.0).315 (14.0) Sq.551 (17.9) Sq.705 Material: Polyamide Protective Guards reduce depth of switch behind panel by.020 (0.5mm). AT4171 Protective Guard Opens 180 loses automatically Splash overs (20.5).807 (10.5).413 (7.1).280 (17.9).705 (18.4).724 (20.4).803 ap Height When Assembled (7.5).295 (14.2).559 (17.9).705 (16.2) Sq.638 AT4171 (39.0) Min* (20.5).807 (10.5).413 Materials: over: lear Polycarbonate Base: Black GFR Polyamide oil Spring: Stainless Steel 180 (20.4).803 (N) = Number of switches (20.4).803 (N) * Minimum dimension allows opening of cover to 180 Recommended Panel Thickness:.039 ~.106 (1.0mm ~ 2.7mm)

10 OPTIAL AESSORIES Protective Guard AT4057 Protective Guard Opens 90 loses manually (26.0) (10.0).394 ap Height When Assembled (8.0).315 (24.15).951 (14.0).551 (21.0).827 Material: Polyamide AT4172 Protective Guard (22.4).882 Protective Guards reduce depth of switch behind panel by.020 (0.5mm). Spring Loaded Protective Guard (20.5).807 (10.5).413 (7.1).280 (17.9).705 (16.2).638 (24.6).969 (26.6) ap Height When Assembled (7.5).295 (20.4).803 (24.1).949 (20.5).807 AT4172 (10.5).413 (26.6) (N) = Number of switches (26.6) (N) (39.0) Min* * Minimum dimension allows opening of cover to 180 Opens 180 loses automatically Materials: over: lear Polycarbonate Base: Black GFR Polyamide oil Spring: Stainless Steel Recommended Panel Thickness:.039 ~.106 (1.0mm ~ 2.7mm) 180 Dust overs AT4002 AT4001 AT4011 (21.0) Dia.827 (15.0) Sq.591 (16.5).650 (16.5).650 (24.0).945 ap Height When Assembled (7.3).287 (2.5).098 (21.8) Dia.858 (30.0) Dia ap Height When Assembled (7.3).287 (2.5).098 (24.0) Sq.945 (22.7).894 (30.2) Materials: PV with polyethylene gasket; PV loses pliability below 0 (32 F). Splash overs reduce depth of switch behind panel by.020 (0.5mm).

11 LB-15SK N.O. Standard Size Pushbuttons Series LB ASSEMBLY INSTRUTIS Incandescent & Neon Lamps AT607 & AT607N Align projections on lamp with grooves (B) in holder when inserting lamp. To correctly join the lamp holder and cap base, match the cut corners (A). B Lamp Installation & LED Orientation Bright LED AT627 Panel Seal Models Snap-in Models For panel seal models, Bright LED must first be inserted into the lamp socket which is built into the switch. The cap can then be placed on the switch. For snap-in models, Bright LED must be inserted into the cap first. Align cut corners () when inserting the LED. Bright & Super Bright LEDs AT625, AT631, AT632, AT635 Align D-flat on LED with flat (B) in holder when inserting the LED. To correctly join the lamp holder and cap base, match the cut corners (A). Attention Electrostatic Sensitive Devices B A 5 LED A B LED D Flat Switch & ap Assembly & Match clip on cap assembly with receptacle inside switch. Lamp terminals will then be aligned correctly with lamp socket. ut orner Projection 3A 125V A 3A 250V A N.. N.. Rubber Seal Projection Notch Match projection () on cap assembly with groove () inside switch. Lamp terminals will then be aligned correctly with lamp socket. Panel Seal With Lamps AT607, AT607N, and LEDs AT614, AT625, AT631, AT632: Match projection on cap assembly with notch inside switch. Lamp terminals will then be aligned correctly with lamp socket. Snap-in Mount Snap-in clip holds all switches firmly in place. To mount round switch, match the antirotation Projection projection on switch with guide cut in Panel panel. Snap into panel cutout. Installation & Maintenance Panel Seal Bushing Mount Insert switch from the front of the panel with the o-ring between the built-in bezel and the panel. Install mounting nut AT075 (supplied with switch) from the rear of the panel. Overtightening mounting nut may damage the switch housing. Bezel O-ring Panel Mounting Nut AT109 ap Extractor Lamp Replacement Actuator must be in UP position. Pull off cap with cap extractor AT109. Replace lamp and reassemble as shown above. AT112 Socket Wrench

12 Standard Size Pushbuttons Series LB LEGENDS LM Easily create and submit your own legends using our new on-line Legend Maker. Visit For other legend support options, customers may either contact the factory and request the LB Legend Packet, or utilize the general information and basic specifications presented below. Suggested Printable Area for Lens Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens. Epoxy based ink is recommended. START (11.68).460 (13.2) (11.68) Sq.460 (17.48) Dia.688 (17.88).704 (19.4).764 Shaded areas are printable areas. Suggested Printable Area for Film Insert Recommended Print Method: Screen Print with Epoxy based ink Lens Film Insert: lear Polyester, 4 mil max. thickness R = (0.6).024 Film Insert (14.66).577 (10.08).397 (11.6).457 Filter or Diffuser (10.08) Sq.397 (11.6) Sq.457 (15.88) Dia.625 (17.4) Dia.685 (16.28).641 (17.8).701 Shaded areas are printable areas. Additional Methods Additional methods for legends are engraving the lens and laser printing on film inserts. Maximum depth for engraving is.012 (0.3mm) on the cap lens. Enamel paint is recommended to fill the engraved area.