General Specifications

Size: px
Start display at page:

Download "General Specifications"

Transcription

1 Standard Size Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 125V AC or 250V AC or 30V C Logic Level (gold): 0.4VA 28V AC/C maximum (Applicable Range 0.1mA ~ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold Insulation Resistance: 200 megohms 500V C ielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit Electrical Life: 100,000 operations minimum Nominal Operating Force: 4.41N Contact Timing: Nonshorting (break-before-make) Travel: Pretravel.059 (1.5mm); Overtravel.059 (1.5mm); Total Travel.118 (3.0mm) Materials & Finishes Housing: Snap-in Frame: Movable Contact: Stationary Contacts: Base: Switch Terminals: Lamp Terminals: Environmental ata Operating Temperature Range: Humidity: Vibration: Shock: Sealing: Installation Cap Installation Force: Quick Connect Force: Soldering Time & Temperature: Standards & Certifications Flammability Standards: UL: CSA: Glass fiber reinforced polyamide (UL94V-0) Stainless steel Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Brass with silver plating 25 C through +50 C ( 13 F through +122 F) for Illuminated 25 C through +70 C ( 13 F through +158 F) for Nonilluminated Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0 C (32 F) 90 ~ 95% humidity for C (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Not available for snap-in; see next section for panel seal. 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. UL94V-0 housing & base File No. E Recognized only when ordered with marking on switch. Add /U or /CUL before first dash in part number to order UL recognized switch. All models recognized at 125V or 250V AC or 28V AC/C maximum. File No _0_000 - Certified only when ordered with marking on switch. Add /C before first dash in part number to order CSA certified switch. All models certified at 125V or 250V AC or 28V AC/C maximum. 48

2 Standard Size Pushbuttons istinctive Characteristics Carefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Spot illumination available in single and bicolor LEs. Choice of super bright LEs in white, green, and blue in addition to standard or bright red, amber, and green LEs. Stainless steel clips provide secure mounting with a wide range of panel thicknesses. Latchdown feature gives indication of circuit status. Audible and tactile feedback with smooth and responsive operation. Snap-action contact mechanism gives long electrical life and sensitivity of actuation. Combination solder lug and.110 quick connect terminals are epoxy sealed to prevent entry of flux, dust, and other contaminants. Panel sealed model meets IP65 of IEC60529 specifications (similar to NEMA 4 & 13). Compact switch design minimizes behind panel depth. Matching indicators available. Actual Size Snap-in Mount Panel Seal Page 48 Page 59 49

3 Standard Size Snap-in Pushbuttons LB Poles 1 SPT 2 PT 1 5 S K W01 Circuits 5 () ( ) = Momentary 6 Alternate Action with Latchdown IMPORTANT: S C R Shapes Switches are supplied without UL, culus and CSA marking unless specified. UL, culus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, and ordering instructions are noted on the General Specifications page. Red, 12-volt, Bright LE with Resistor SPT -() Circuit Silver Contacts Rated 125/250V AC; Solder Lug/Quick Connect Terminals K G W01 G01 ESCRIPTI FOR TYPICAL ORERING EXAMPLE LB15SKW01-5C12- Housing Black Gray Clear Cap with Red iffuser Shape Black Housing TYPICAL SWITCH Contacts & Terminals Silver Contacts Rated 125/250V AC Solder Lug/Quick Connect Terminals Gold Contacts Rated 28V AC/C Solder Lug/Quick Connect Terminals 50

4 Standard Size Snap-in Pushbuttons ORERING EXAMPLE 5C 12 Incandescent Lamp Used with Solid Cap 05 5-volt volt No Code Nonilluminated Incandescent or Neon Used with Insert Cap volt Neon 05 5-volt Incandescent volt Incandescent No Code 5C 5 5F 6B 6F 6G 1C 1 1F CF No Code Bright LE Used with LE Cap Colors Red Amber Green Super Bright LE Used with LE Cap White Green Blue Lamps Nonilluminated No Code Resistor 05 5-volt No Resistor volt volt LE in Spot Illuminated Cap Red Single Color Amber Single Color Green Single Color Red/Green Bicolor Nonilluminated Nonilluminated BJ CJ EJ FJ GJ JE *JF *JG J JF A B C F Cap Types & Colors Solid Cap: Lens/Filter Colors White/Clear Red/Clear Yellow/Clear Green/Clear Blue/Clear Insert Cap: Lens/Filter Colors Clear/White Clear/Red Clear/Yellow Clear/Green Clear/Blue *JF & JG not suitable with neon. LE Cap: Lens/iffuser Colors Clear/White Clear/Red Clear/Amber Clear/Green LE Cap: Lens/iffuser Colors Clear/White Spot Illuminated Cap Colors Black White Red Green Available in and only. Nonilluminated Cap Colors A Black F Green B White G Blue C Red H Gray E Yellow 51

5 Standard Size Snap-in Pushbuttons Pole SP P S Housing Colors Available: W01 G01 Model LB15 *LB16 LB25 *LB26 * When in latchdown position for the alternate circuit, cap position is.039 (1.0mm) above the built-in bezel..622 (15.8mm) (16.2) Sq.638 Cutout for 1 switch:.638 x.638 (16.2mm x 16.2mm) Cutout for 1 switch with barriers:.638 x.815 (16.2mm x 20.7mm) Silver Contacts Gold Contacts C SHAPES & PANEL CUTOUTS.854 (21.7mm) K HOUSING CTACT MATERIALS, RATINGS & TERMINALS Power Level 125V AC & 250V AC (1.5) R.059 Logic Level 0.4VA 28V AC/C max. (22.0) ia.866 Panel Thickness for Switches & Barriers:.039 ~.157 (1.0 ~ 4.0mm) Panel Thickness for Protective Guards & Splash Covers:.039 ~.138 (1.0 ~ 3.5mm) Black Complete explanation of operating range in Supplement section. AT607 & AT607N T-1 Bi-pin Plunger Position ( ) = Momentary Connected Terminals Throw & Switch/Lamp Schematics Normal own Normal own Notes: Switch is marked with NC,,, L+, L. Lamp circuit is isolated and requires an external power source. () () AT607 Incandescent 5-volt or 12-volt; AT607N Neon 110-volt POLES & CIRCUITS SPT PT (11.5).453 R G Solder Lug/Quick Connect Voltage V 5V AC 12V AC 110V AC Current I 115mA 60mA 1.5mA Endurance Avg. Hours 10,000 10,000 Ambient Temp. Range C ~ +50 C NC x.866 (15.8mm x 22.0mm) Epoxy Seal (22.4).882 (7.5).295 (2.0).079 (2.8).110 (1.2).047 Thk = (0.5).020 The electrical specifications shown are determined at a basic temperature of 25 C. Lamp circuit is isolated and requires external power source. * Recommended Resistors for Neon: 33K ohms for 110V AC; 100K ohms for 220V AC (16.2).638 Cutout for 1 switch:.638 x.882 (16.2mm x 22.4mm) Cutout for 1 switch with barriers:.638 x (16.2mm x 26.9mm) Gray 3 NC 2 6 NC 5 4 Optional PCB adaptors AT711 & AT712 available; illustrated in Optional Accessories immediately following Typical Switch imensions. INCANESCENT & NE LAMP COES & SPECIFICATIS 01 * L (+) L (+) (-) L (-) L 52

6 Standard Size Snap-in Pushbuttons AT635 LEs are colored in OFF state. AT627 with Resistor AT627 5-volt 4-element with Resistor AT625G Blue AT631B White AT632F Green No Code (+) (-) T Bi-pin T-1 Bi-pin LE COLORS & SPECIFICATIS The electrical specifications shown are determined at a basic temperature of 25 C. LE circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. (+) (-) (+) (-) T-1 Bi-pin No Lamp Color Codes Bright LE without Resistor (+) (-) Red Amber Green Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current I F 20mA 20mA 20mA Forward Voltage V F 1.9V 2.0V 2.1V Maximum Reverse Voltage V RM 5V 5V 5V Current Reduction Rate Above 25 C I F 0.42mA/ C Ambient Temperature Range Color Codes: AT volt 4-element with Resistor Red Amber Green 5C 5 5F Bright LE with Resistor Super Bright Single Element LE No Code 25 ~ +50 C No Resistor Color White Green Blue Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current I F 20mA 20mA 20mA Forward Voltage V F 3.3V 3.3V 3.3V Maximum Reverse Voltage V RM 7V 7V 7V Current Reduction Rate Above 25 C I F 0.40mA/ C 0.40mA/ C 0.40mA/ C Ambient Temperature Range AT volt 4-element with Resistor 6B Resistor Codes Maximum Forward Current I FM Typical Forward Current I F 52mA 26mA 13mA Forward Voltage V F 5V 12V 24V Maximum Reverse Voltage V RM 4V 8V 16V Current Reduction Rate Above 25 C I F 0.50mA/ C Ambient Temperature Range Red Amber Green 5C 5 5F ATTENTI ELECTROSTATIC SENSITIVE EVICES 25 ~ +50 C (+) 6F 25 ~ +50 C 6G (-) 53

7 Standard Size Snap-in Pushbuttons Lens/Filter Colors Available: BJ CJ EJ FJ GJ Lens/Filter Colors Available: JE JF and JG not suitable with neon lamp. AT476 CAP TYPES & COLOR BINATIS Color Codes: B White C Red Amber E Yellow F Green G Blue J Clear JF JG Lens/iffuser Colors Available: J JF Lens/iffuser Colors Available: J JF (13.2) Sq (13.2) Sq (13.2) Sq (13.2) Sq AT4176 AT4162 AT477 (3.5).138 Solid Cap for Incandescent Lamp & Nonilluminated AT4012 Material: Polycarbonate AT4013 Material: Polycarbonate Insert Cap for Incandescent or Neon Lamp & Nonilluminated (6.5).256 (3.5).138 (6.5).256 (3.5).138 (3.5).138 (6.5).256 (6.5).256 (19.0) ia (19.0) ia AT4178 Material: Polycarbonate (4.5).177 (5.5).217 (4.5).177 (5.5).217 (13.2) (13.2) Cap for Bright LE without Resistor (19.0) ia Material: Polycarbonate Cap for Bright LE with Resistor (19.0) ia AT4164 (4.5).177 (5.5).217 (4.5).177 ( (13.2) (13.2) AT4026 (19.4).764 AT4027 (19.4).764 AT4177 AT4163 (19.4).764 (19.4).764 (5.0).197 (6.0).236 (5.0).197 (6.0).236 (5.0).197 (6.0).236 (5.0).197 (6.0).236 Translucent Colored Lens Transparent Clear Filter Lamp AT607 Transparent Clear Lens Translucent Colored Filter Lamp AT607 or 607N Transparent Clear Lens Translucent Colored iffuser Bright LE AT635 Transparent Clear Lens Translucent Colored iffuser Bright LE AT627 54

8 Standard Size Snap-in Pushbuttons CAP TYPES & COLOR BINATIS Color Codes: A Black B White C Red Amber E Yellow F Green G Blue H Gray J Clear Material: Polycarbonate Clear Lens White iffuser (13.2) Sq AT4129 (3.5).138 (6.5).256 (19.0) ia Cap for Super Bright LEs AT4128 Spot Illuminated Cap with LE AT4130 Transparent Clear Lens Translucent White iffuser LEs AT625 AT631 AT632 The electrical specifications shown are determined at a basic temperature of 25 C. LE circuit is isolated and requires an external power source. Single color LEs are colored in OFF state; bicolor LEs are translucent white in OFF state. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. LE factory assembled in Spot Illuminated Caps Not Available Separately Cap Colors Available: A B C F Material: Polycarbonate Cap Colors Available: A B C E F G AT480 (4.5).177 (5.5).217 (13.2) (19.4).764 Single Color AT4016 (5.0).197 (6.0).236 When ordering spot illuminated cap separately, LE color must be specified. Examples: AT480CA (red LE, black cap); AT4016CFB (red/green bicolored LE, white cap) H Single Color LE with 1 Element Bicolor Red Amber Green Red/Green Maximum Forward Current I FM 25mA 30mA 25mA 30/25mA Typical Forward Current I F 20mA 20mA 20mA 20mA Forward Voltage V F 2.25V 2.1V 2.2V 2.0/2.2V Maximum Reverse Voltage V RM 5V 5V 5V Current Reduction Rate Above 25 C I F 0.33mA/ C 0.40mA/ C 0.33mA/ C 0.43/0.38mA/ C Ambient Temperature Range LE Specifications Bicolor LE with 2 Elements (+) (-) (+) (-) (13.2) Sq (13.2) Sq AT484 (4.0).157 (2.0).079 (5.0).197 (3.5).138 (6.5).256 (3.5).138 (6.5).256 Material: Polycarbonate 1C 1 (19.0) ia (5.0).197 (4.5).177 (5.5).217 (2.0).079 (6.0).236 Cap for Nonilluminated AT4017 (19.0) ia (4.5).177 (5.5).217 (13.2) 1F 25 ~ +70 C AT4030 (19.4).764 CF Cap with Window Factory Assembled LE; Not Available Separately (5.0).197 (6.0).236 Cap No Lamp 55

9 Standard Size Snap-in Pushbuttons (13.2) Sq NC L (+) (-) NC (5.08).200 TYPICAL SWITCH IMENSIS (15.8) Sq.622 Single & ouble Pole LB15SKW01-12-CJ Single pole models do not have terminals 4, 5, & 6. Single & ouble Pole LB16CKW01-12-CJ Single pole models do not have terminals 4, 5, & 6. (13.2) (17.8).701 (17.8) Sq.701 (19.0) ia (23.7) ia.933 (19.4).764 (24.0).945 Single & ouble Pole LB26RGW01-12-CJ Single pole models do not have terminals 4, 5, & 6. (5.08).200 (1.0).039 (3.2).126 (1.8).071 (1.8).071 (1.0).039 (3.2).126 (1.8).071 (1.0).039 (3.2).126 (2.54) Typ.100 (1.0) ia Typ.039 (21.5).846 Latchdown Position (21.5).846 Latchdown Position (22.5).886 Latchdown Position OPTIAL ACCESSORIES (0.5).020 (15.0) (4.0) (7.5).295 (7.5).295 (7.5).295 (0.3) Typ.012 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ.020 (2.54) Typ.100 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ.020 (2.54) Typ.100 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ.020 (2.54) Typ.100 (0.74) Typ.029 (2.54) Typ.100 NC NC NC 3 L (+) L (-) L (+) L (-) 4 4 (2.8) Typ.110 (5.08) Typ.200 (2.8) Typ.110 (5.08) Typ.200 L (+) L (-) (5.08) Typ.200 (22.0).866 PCB Adaptors AT711 Single Pole Straight PC Terminals AT712 ouble Pole Straight PC Terminals (0.5).020 (15.0) (4.0) (0.3) Typ.012 L (2.54) Typ.100 (0.74) Typ.029 Note: Order adaptors separately. NC L L (+) NC (-) (5.08).200 (15.8) Sq (15.8) Sq.622 (15.8) Sq.622 (21.7) ia.854 (5.08) Typ.200 (15.8).622 (2.8) Typ.110 (2.54) Typ.100 (1.0) ia Typ

10 Standard Size Snap-in Pushbuttons AT497 End (20.0).787 End Position Material: Polyamide AT499 Protective Guard Opens 90 Closes manually Material: Polyamide AT4171 Protective Guard Opens 180 Closes automatically (16.2) Sq.638 AT4171 (20.5).807 (10.5).413 AT498 Center Center Position (4.3) Typ.169 (5.2).205 (15.0).591 (1.19).047 OPTIAL ACCESSORIES (23.5).925 (19.2).756 (1.19).047 (19.2).756 Barriers Protective Guard (21.0).827 (10.0).394 (17.0).669 Cutouts for More Than 1 Switch A =.752 (19.1mm) x Number of Switches (1.3mm) A =.996 (25.3mm) x Number of Switches (1.3mm) (20.0).787 Cap Height When Assembled Protective Guards reduce depth of switch behind panel by.020 (0.5mm). (39.0) Min* (20.4).803 (20.4).803 (N) (N) = Number of switches * Minimum dimension allows opening of cover to 180 Spring Loaded Protective Guard (20.5).807 (10.5).413 (18.4).724 (20.4).803 Cap Height When Assembled Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel A (8.0).315 (7.5).295 Recommended Panel Thickness:.039 ~.106 (1.0mm ~ 2.7mm) (16.2).638 (14.2) (14.0) Sq.551 (17.9) Sq.705 (17.9).705 (7.1).280 (17.9)

11 Standard Size Snap-in Pushbuttons AT4057 Protective Guard Opens 90 Closes manually Material: Polyamide AT4172 Protective Guard (20.5).807 (16.2).638 AT4172 (10.5).413 (N) = Number of switches AT4002 (21.0) ia.827 Cap Height When Assembled (26.6) (7.3).287 (22.4).882 (2.5).098 (26.6) (N) * Minimum dimension allows opening of cover to 180 (21.8) ia.858 (30.0) ia OPTIAL ACCESSORIES Protective Guard Protective Guards reduce depth of switch behind panel by.020 (0.5mm). Spring Loaded Protective Guard (39.0) Min* AT4001 (20.5).807 (15.0) Sq.591 Cap Height When Assembled (10.5).413 (24.6).969 ust Covers (7.3).287 (26.6) Opens 180 Closes automatically Cap Height When Assembled Materials: Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless Steel (7.5).295 Recommended Panel Thickness:.039 ~.106 (1.0mm ~ 2.7mm) Materials: PVC with polyethylene gasket; PVC loses pliability below 0 C (32 F). ust Covers reduce depth of switch behind panel by.020 (0.5mm). (26.0) (2.5).098 (10.0).394 Cap Height When Assembled (24.0) Sq.945 (8.0).315 AT4011 (16.5).650 (22.7).894 (24.15).951 (20.4) (30.2) (24.1).949 (14.0).551 (21.0).827 (7.1).280 (17.9).705 (16.5).650 (24.0)

12 Standard Size Panel Seal Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 125V AC or 250V AC or 30V C Logic Level (gold): 0.4VA 28V AC/C maximum (Applicable Range 0.1mA ~ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold Insulation Resistance: 200 megohms 500V C ielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life: 1,000,000 operations minimum for momentary circuit 200,000 operations minimum for maintained circuit Electrical Life: 100,000 operations minimum Nominal Operating Force: 5.39N Contact Timing: Nonshorting (break-before-make) Travel: Pretravel.059 (1.5mm); Overtravel.059 (1.5mm); Total Travel.118 (3.0mm) Materials & Finishes Housing: O-ring: Inner Seal: Movable Contact: Stationary Contacts: Base: Switch Terminals: Lamp Terminals: Environmental ata Operating Temperature Range: Humidity: Vibration: Shock: Installation Mounting Torque: Cap Installation Force: Quick Connect Force: Soldering Time & Temperature: Standards & Certifications Flammability Standards: UL: Glass fiber reinforced polyamide (UL94V-0) Nitrile butadiene rubber Silicone rubber Silver alloy or copper with gold plating Silver alloy or copper with gold plating Liquid crystal polymer (UL94V-0) Phosphor bronze with silver or gold plating Brass with silver plating 25 C through +50 C ( 13 F through +122 F) for Illuminated 25 C through +70 C ( 13 F through +158 F) for Nonilluminated Note: When used with a polyvinyl chloride splash cover, the lowest limit is 0 C (32 F) 90 ~ 95% humidity for C (104 F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s 2 ) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sealing: IP65 of IEC60529 standard (similar to NEMA 4 & 13) CSA: 1.96Nm (17.35 lb in) maximum 3.92N maximum downward force on cap 52.95N maximum downward force on connector Manual Soldering: See Profile A in Supplement section. UL94V-0 housing & base File No. E Recognized only when ordered with marking on switch. Add /U or /CUL before first dash in part number to order UL recognized switch. All models recognized at 125V or 250V AC or 28V AC/C maximum. File No _0_000 - Certified only when ordered with marking on switch. Add /C before first dash in part number to order CSA certified switch. All models certified at 125V or 250V AC or 28V AC/C maximum. 59

13 Standard Size Panel Seal Pushbuttons LB Poles 1 SPT 2 PT Red, 12-volt, Bright LE with Resistor ESCRIPTI FOR TYPICAL ORERING EXAMPLE Shape Black Housing W Shape LB16WKW01-5C12- K G Housing Black Gray Clear Cap with Red iffuser SPT - Circuit Silver Contacts Rated 125/250V AC; Solder Lug/Quick Connect Terminals TYPICAL SWITCH 1 6 W K W01 Circuits 5 () ( ) = Momentary 6 Alternate Action with Latchdown IMPORTANT: Switches are supplied without UL, culus & CSA marking unless specified. UL, culus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. W01 G01 Contacts & Terminals Silver Contacts Rated 125/250V AC Solder Lug/Quick Connect Terminals Gold Contacts Rated 28V AC/C Solder Lug/Quick Connect Terminals 60

14 Standard Size Panel Seal Pushbuttons ORERING EXAMPLE 5C 12 Incandescent Lamp Used with Solid Cap 05 5-volt volt No Code 6B 6F 6G Nonilluminated Incandescent or Neon Used with Insert Cap volt Neon 05 5-volt Incandescent volt Incandescent No Code 5C 5 5F Bright LE Used with LE Cap Colors Nonilluminated Red Amber Green Super Bright LE Used with LE Cap White Green Blue Lamps No Code Resistor 05 5-volt No Resistor volt volt BJ CJ EJ FJ GJ JE *JF *JG J JF Cap Types & Colors Solid Cap: Lens/Filter Colors White/Clear Red/Clear Yellow/Clear Green/Clear Blue/Clear Insert Cap: Lens/Filter Colors Clear/White Clear/Red Clear/Yellow Clear/Green Clear/Blue *JF & JG not suitable with neon. LE Cap: Lens/iffuser Colors Clear/White Clear/Red Clear/Amber Clear/Green LE Cap: Lens/iffuser Colors Clear/White 61

15 Standard Size Panel Seal Pushbuttons Pole SP P W.866 (22.0mm) Housing Colors Available: W01 G01 Model LB15 *LB16 LB25 *LB26 Silver Contacts Gold Contacts Plunger Position ( ) = Momentary Connected Terminals Throw & Switch/Lamp Schematics Normal own Normal own Notes: Switch is marked with NC,,, L+, L. Lamp circuit is isolated and requires external power source. SHAPE & PANEL CUTOUT K HOUSING CTACT MATERIALS, RATINGS & TERMINALS Power Level 125V AC & 250V AC Logic Level 0.4VA 28V AC/C max. Recommended Panel Thickness:.039 ~.157 (1.0mm ~ 4.0mm) Recommended Panel Thickness with Splash Cover:.039 ~.138 (1.0mm ~ 3.5mm) Overtightening the mounting nut AT074 may damage the switch housing. Black Complete explanation of operating range in Supplement section. AT607 & AT607N T-1 Bi-pin () () SPT PT * When in latchdown position for the alternate circuit, cap position is.039 (1.0mm) above the built-in bezel. AT607 Incandescent 5-volt or 12-volt; AT607N Neon 110-volt POLES & CIRCUITS G Gray Solder Lug/Quick Connect Voltage V 5V AC 12V AC 110V AC Current I 115mA 60mA 1.5mA Endurance Avg. Hours 10,000 10,000 Ambient Temp. Range C ~ +50 C NC 2 3 NC 2 6 NC 5 Optional PCB adaptors AT711 & AT712 available; illustrated in previous snap-in subsection. INCANESCENT & NE LAMP COES & SPECIFICATIS 01 * 4 Epoxy Seal L (+) L (+) (1.7).067 (7.5).295 (2.0).079 (2.8).110 (1.2).047 (-) L (-) L Thk = (0.5).020 The electrical specifications shown are determined at a basic temperature of 25 C. Lamp circuit is isolated and requires external power source. * Recommended Resistors for Neon: 33K ohms for 110V AC; 100K ohms for 220V AC (10.5).413 (22.0) ia

16 Standard Size Panel Seal Pushbuttons AT635 LEs are colored in OFF state. AT627 with Resistor AT627 5-volt 4-element with Resistor AT625G Blue AT631B White AT632F Green No Code (+) (-) T Bi-pin T-1 Bi-pin LE COLORS & SPECIFICATIS The electrical specifications shown are determined at a basic temperature of 25 C. LE circuit is isolated and requires external power source. Polarity marks are on the switch. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Additional lamp detail is shown in the Accessories & Hardware section. (+) (-) (+) (-) T-1 Bi-pin No Lamp Bright LE without Resistor Color Codes Red Amber Green Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current I F 20mA 20mA 20mA Forward Voltage V F 1.9V 2.0V 2.1V Maximum Reverse Voltage V RM 5V 5V 5V Current Reduction Rate Above 25 C I F 0.42mA/ C Ambient Temperature Range Color Codes: AT volt 4-element with Resistor Red Amber Green 5C 5 5F Bright LE with Resistor (+) (-) Super Bright Single Element LE No Code 25 ~ +50 C No Resistor Color White Green Blue Maximum Forward Current I FM 30mA 30mA 30mA Typical Forward Current I F 20mA 20mA 20mA Forward Voltage V F 3.3V 3.3V 3.3V Maximum Reverse Voltage V RM 7V 7V 7V Current Reduction Rate Above 25 C I F 0.40mA/ C 0.40mA/ C 0.40mA/ C Ambient Temperature Range AT volt 4-element with Resistor 6B Resistor Codes Maximum Forward Current I FM Typical Forward Current I F 52mA 26mA 13mA Forward Voltage V F 5V 12V 24V Maximum Reverse Voltage V RM 4V 8V 16V Current Reduction Rate Above 25 C I F 0.50mA/ C Ambient Temperature Range Red Amber Green 5C 5 5F ATTENTI ELECTROSTATIC SENSITIVE EVICES 25 ~ +50 C (+) 6F 25 ~ +50 C 6G (-) 63

17 Standard Size Panel Seal Pushbuttons Lens/Filter Colors Available: BJ CJ EJ FJ GJ Lens/Filter Colors Available: JE JF and JG not suitable with neon lamp. CAP TYPES & COLOR BINATIS Color Codes: B White C Red Amber E Yellow F Green G Blue J Clear JF JG Lens/iffuser Colors Available: J JF Lens/iffuser Colors Available: J JF AT4054 AT4055 AT4179 AT4165 Solid Cap for Incandescent Lamp & Nonilluminated (19.0) ia (19.0) ia (19.0) ia (19.0) ia (5.1).201 Material: Polycarbonate (5.1).201 Material: Polycarbonate (5.1).201 (5.1).201 Translucent Colored Lens Insert Cap for Incandescent or Neon Lamp & Nonilluminated Material: Polycarbonate Transparent Clear Lens Cap for Bright LE without Resistor Material: Polycarbonate Transparent Clear Lens Cap for Bright LE with Resistor Transparent Clear Lens Transparent Clear Filter Translucent Colored Filter Translucent Colored iffuser Translucent Colored iffuser Lamp AT607 Lamp AT607 Lamp AT607N Bright LE AT635 Bright LE AT627 64

18 Standard Size Panel Seal Pushbuttons Material: Polycarbonate Clear Lens White iffuser (19.0) ia (25.0) ia.984 AT4131 AT9410 Splash Cover for Panel Seal Materials: Lid: PVC (loses pliability below 0 C/32 F) Base: Polyethylene O-ring: NBR Recommended Panel Thickness:.039 ~.138 (1.0mm ~ 3.5mm) (31.3) ia (1.8).071 (1.0).039 (3.2).126 (21.0) ia.827 CAP TYPES & COLOR BINATIS (5.5).217 (12.0).472 (21.5).846 Latchdown Position Cap for Super Bright LEs Transparent Clear Lens TYPICAL SWITCH IMENSIS Single & ouble Pole Single pole models do not have terminals 4, 5, & 6. (7.8).307 M22 P1 (7.5).295 (1.2) x (2.0) Typ.047 x.079 (0.5) Typ.020 (2.54) Typ.100 OPTIAL ACCESSORIES (3.0).118 (19.0) ia (5.1).201 (1.6).063 (23.0) ia.906 NC (2.8) Typ.110 (10.6).417 L (+) L (-) 4 Keyway (5.08) Typ.200 Lid Base O-ring Supplied with Panel Seal Switch O-ring Supplied with AT9410 Splash Cover Translucent Colored iffuser (15.8) Sq.622 (22.0) ia.866 LEs AT625 AT631 AT632 Panel Seal LB25WKW (31.3) ia (0.5)

19 N.O. Standard Size Pushbuttons Incandescent & Neon Lamps AT607 & AT607N Align projections on lamp with grooves (B) in holder when inserting lamp. To correctly join the lamp holder and cap base, match the cut corners (A). C C 3A 125V AC 3A 250V AC LB-15SK Match projection (C) on cap assembly with groove (C) inside switch. Lamp terminals will then be aligned correctly with lamp socket. B B Snap-in Mount Snap-in clip holds all switches firmly in place. To mount round switch, match the antirotation Projection projection on switch with guide cut in Panel panel. Snap into panel cutout. N.C. N.C. A ASSEMBLY INSTRUCTIS Lamp Installation & LE Orientation Panel Seal Models For panel seal models, Bright LE must first be inserted into the lamp socket which is built into the switch. The cap can then be placed on the switch. Bright LE AT627 Snap-in Models For snap-in models, Bright LE must be inserted into the cap first. Align cut corners (C) when inserting the LE. Switch & Cap Assembly & Match clip on cap assembly with receptacle inside switch. Lamp terminals will then be aligned correctly with lamp socket. Installation & Maintenance Panel Seal Bushing Mount Insert switch from the front of the panel with the o-ring between the built-in bezel and the panel. Install mounting nut AT075 (supplied with switch) from the rear of the panel. Overtightening mounting nut may damage the switch housing. C 5 LE Bezel O-ring Panel Mounting Nut Bright & Super Bright LEs AT625, AT631, AT632, AT635 Align -flat on LE with flat (B) in holder when inserting the LE. To correctly join the lamp holder and cap base, match the cut corners (A). Projection Notch Rubber Seal Panel Seal With Lamps AT607, AT607N, and LEs AT614, AT625, AT631, AT632: Match projection on cap assembly with notch inside switch. Lamp terminals will then be aligned correctly with lamp socket. AT109 Cap Extractor Cut Corner LE ATTENTI ELECTROSTATIC SENSITIVE EVICES Lamp Replacement Projection Actuator must be in UP position. Pull off cap with cap extractor AT109. Replace lamp and reassemble as shown above. A Flat B AT112 Socket Wrench 66

20 Standard Size Pushbuttons START LEGENS NKK Switches can provide custom legends for caps. Contact factory for more information. Lens Film Insert Filter or iffuser Suggested Printable Area for Lens Recommended Methods: Laser Etch on clear lens, Screen Print, or Pad Print on lens. (11.68) Sq.460 (13.2) Sq Shaded areas are printable areas. Suggested Printable Area for Film Insert Recommended Print Method: Laser Print or Screen Print with Epoxy based ink Film Insert: Clear Polyester, 4 mil max. thickness (10.08) Sq.397 (11.6) Sq.457 Epoxy based ink is recommended. (0.76) Typ.030 (0.76) Typ.030 (14.66).577 (17.48) ia.688 (19.0) ia (15.88) ia.625 (17.4) ia.685 R = (0.6).024 (0.76) Typ.030 (0.76) Typ.030 Shaded areas are printable areas. (17.88).704 (19.4).764 (16.28).641 (17.8).701 (0.76) Typ.030 (11.68).460 (0.76) Typ.030 (0.76) Typ.030 (10.08).397 (0.76) Typ.030 (13.2) (11.6)

General Specifications

General Specifications Standard Size Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V C Logic Level (gold): 0.4VA maximum @ 28V AC/C maximum

More information

Distinctive Characteristics

Distinctive Characteristics Standard Size Pushbuttons istinctive Characteristics Carefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Spot illumination available

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Carefully designed light diffusion and filtering system produce bright, full surface illumination with front panel relamping. Spot illumination available in single and bicolor

More information

General Specifications

General Specifications Series YB Short Body Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V C Logic Level (gold): 0.4VA maximum @ 28V AC/C

More information

General Specifications

General Specifications General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V C Logic Level (gold): 0.4VA maximum @ 28V AC/C maximum (Applicable Range 0.1mA

More information

General Specifications

General Specifications Series UB Low Profile Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 5A @ 5/50V AC or 5A @ 0V C Logic Level (gold): 0.VA maximum @ 8V AC/C maximum (Applicable

More information

General Specifications

General Specifications Series UB Low Profile Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 5A @ 5/50V AC or 5A @ 0V C Logic Level (gold): 0.VA maximum @ 8V AC/C maximum (Applicable

More information

General Specifications

General Specifications General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V C Logic Level (gold): 0.4VA maximum @ 28V AC/C maximum (Applicable Range 0.1mA

More information

General Specifications

General Specifications Standard Size Pushbuttons General Specifications Electrical apacity (Resistive Load) Power Level (silver): 3A @ 125V A or 3A @ 250V A or 3A @ 30V Logic Level (gold): 0.4VA maximum @ 28V A/ maximum (Applicable

More information

General Specifications

General Specifications General Specifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V C Logic Level (gold): 0.4VA maximum @ 28V AC/C maximum (Applicable Range 0.1mA

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Full face or spot illumination with incandescent lamps or multi-element LEDs, with or without resistors. Choice of super bright LEDs in white, green, and blue as well as bright

More information

General Specifications

General Specifications Series UB Low Profile Pushbuttons General Specifications Electrical Capacity (Resistive Load) Power Level (silver): A @ /0V AC or A @ 0V C Logic Level (gold): 0.VA maximum @ 8V AC/C maximum (Applicable

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Full face or spot illumination with incandescent lamps or multi-element LEDs, with or without resistors. Short Body Pushbuttons Series YB Choice of super bright LEDs in white,

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive haracteristics arefully designed light diffusion and filtering system produces bright, full surface illumination with front panel relamping. Spot illumination available in single and bicolor

More information

General Specifications

General Specifications General Specifications Electrical Capacity (Resistive oad) Power evel (silver): A @ 25/250V AC or A @ 30V C ogic evel (gold): 0.VA maximum @ 28V AC/C maximum (Applicable Range 0.mA ~ 0.A @ 20mV ~ 28V)

More information

General Specifications

General Specifications General Specifications Electrical Capacity (Resistive oad) Power evel (silver): 3A @ 125V AC or 3A @ 250V AC or 3A @ 30V C ogic evel (gold): 0.4VA maximum @ 28V AC/C maximum (Applicable Range 0.1mA ~ 0.1A

More information

General Specifications

General Specifications General Specifications Electrical Capacity (Resistive oad) Power evel (silver): A @ 25/250V AC or A @ 30V C ogic evel (gold): 0.VA maximum @ 28V AC/C maximum (Applicable Range 0.mA ~ 0.A @ 20mV ~ 28V)

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Wide selection of illumination effects is achieved with single and bicolor, - or -element LEDs, in flat, beveled, or sculptured caps. LED colors include red, amber, green, white,

More information

We Make It Easy! 3. All of our switches are shipped complete, just as ordered. No incomplete or partial deliveries of subcomponents and accessories

We Make It Easy! 3. All of our switches are shipped complete, just as ordered. No incomplete or partial deliveries of subcomponents and accessories We Make It Easy! 1. We assemble the parts for you saves you time and money. Includes LEDs and accessories 2. Easy to order all options and accessories displayed in easy-to-follow ordering table. No complicated

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Full face and spot illumination available. Front panel relamping. Choice of super bright LEDs in white, green, and blue in addition to bright red, amber, and green LEDs. Compact

More information

General Specifications

General Specifications Series HB Subminiature Pushbuttons General Specifications Electrical apacity (Resistive Load) Power Level (silver): 0.1A maximum @ 30V A/ Other Ratings ontact Resistance: 50 milliohms maximum Insulation

More information

Complement to LB Pushbuttons LB Indicators TYPICAL INDICATOR ORDERING EXAMPLE LAMPS. Incandescent Lamp used with Solid Cap 05 5-volt volt

Complement to LB Pushbuttons LB Indicators TYPICAL INDICATOR ORDERING EXAMPLE LAMPS. Incandescent Lamp used with Solid Cap 05 5-volt volt TYPICAL INDICATOR ORDERING EXAMPLE LB 01 G W01 5C 12 W01 SHAPES 01 02 03 K G HOUSING Black Grey TERMINALS Silver Solder Lug/ Quick Connect Terminals LAMPS Incandescent Lamp used with Solid Cap 05 5-volt

More information

YB2 Panel Seal. New Square Actuator Option. Series YB2. Contact No Thin Flush Mount Pushbuttons. 24mm Square Panel Seal Pushbuttons

YB2 Panel Seal. New Square Actuator Option. Series YB2. Contact No Thin Flush Mount Pushbuttons. 24mm Square Panel Seal Pushbuttons Contact No. 182 YB2 Panel eal Thin Flush Mount Pushbuttons New quare Actuator Option 2011-01-26 www.nkk.com 1 General pecifications Electrical Capacity (Resistive Load) Power Level (silver): 3A @ 125V

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Various cap styles and colors to meet differing application needs. Bright, full face illumination to distinctively indicate status. Rear panel threaded mounting or snap-in mounter

More information

TYPICAL INDICATOR ORDERING EXAMPLE W01. Lamps. Incandescent Lamp Used with Solid Cap 05 5-volt volt

TYPICAL INDICATOR ORDERING EXAMPLE W01. Lamps. Incandescent Lamp Used with Solid Cap 05 5-volt volt K Shapes 01 02 03 LB Housing Black ray Terminals Silver Solder Lug/ Quick Connect Terminals 01 TYPICAL INDICATOR ORDERIN EXAPLE DESCRIPTION FOR TYPICAL ORDERIN EXAPLE Clear Cap with Red Diffuser Incandescent

More information

General Specifications

General Specifications Series JW High Inrush 0 & 6 Amp Rockers Touch Tilt Rockers Toggles Slides Rotaries Programmable Illuminated P Pushbuttons Supplement Accessories Indicators Tactiles Keylocks General Specifications Electrical

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Subminiature size saves space on PC boards. Specifically developed for logic-level applications. Antistatic superstructure, consisting of the carbon impregnated bushing and

More information

TYPICAL INDICATOR ORDERING EXAMPLE. Lamps. Incandescent Lamp Used with Solid Cap 05 5-volt volt. Incandescent or Neon Lamp Used with Insert Cap

TYPICAL INDICATOR ORDERING EXAMPLE. Lamps. Incandescent Lamp Used with Solid Cap 05 5-volt volt. Incandescent or Neon Lamp Used with Insert Cap KB K Shapes Bushing ounting 01 02 03 Snap-in ounting 04 05 06 W01 Housing Black only Terminals Silver Solder Lug* * Wire harness & cable assemblies offered only in Americas TYPICAL INDICATOR ORDERING EXAPLE

More information

General Specifications

General Specifications Touch Tilt Rockers Toggles Slides Rotaries Programmable Illuminated P Pushbuttons General Specifications High Inrush 0 & 6 Amp Rockers Electrical Capacity (Resistive Load) Power Level: 0A @ 5/50V AC for

More information

General Specifications

General Specifications Series JWS Internationally pproved Rockers Touch Tilt Rockers Toggles Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators Tactiles Keylocks General Specifications Electrical

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics Subminiature size saves space on PC boards. Specifically developed for logic-level applications. ntistatic superstructure, consisting of the carbon impregnated bushing and the

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics ntirotation design, standard on noncylindrical levers, mates toggle and bushing; bottom of toggles has two flatted sides which fit into a complementary opening inside bushing.

More information

General Specifications

General Specifications Series D Light Touch Miniature Pushbuttons General Specifications Electrical apacity (Resistive Load) Logic Level: 0.VA maximum @ 8V A/D maximum (Applicable Range 0.mA ~ 0.A @ 0mV ~ 8V) Note: Find additional

More information

General Specifications

General Specifications Series E Light Touch Miniature Pushbuttons eneral Specifications Electrical apacity (Resistive Load) Power Level (silver): A @ 25V A for silver contacts Logic Level (gold): 0.4VA maximum @ 28V A/D maximum

More information

General Specifications

General Specifications Series WT Environmentally Sealed General Specifications Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical Capacity

More information

General Specifications

General Specifications eneral Specifications Miniature Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated P Pushbuttons Rockers Electrical apacity (Resistive Load) Power Level

More information

General Specifications

General Specifications Series M eneral Specifications Miniature Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical apacity (Resistive Load)

More information

General Specifications

General Specifications Series FB & SB Momentary Pushbuttons General Specifications FB Series Electrical apacity (Resistive Load) Power Level: 500mA @ 125V A for silver Logic Level: 0.4VA max. @ 28V A/D max. for gold (Applicable

More information

General Specifications

General Specifications Slides Rotaries Programmable Illuminated P Pushbuttons Supplement ccessories Indicators eneral Specifications lectrical apacity Resistive Load: 0 @ 5V, @ 50V, or @ 0V Inductive Load: 5 @ 5V (P.. @.0) Other

More information

General Specifications

General Specifications Series FB & SB Momentary Pushbuttons General Specifications FB Series Electrical apacity (Resistive Load) Power Level: 500mA @ 125V A for silver Logic Level: 0.4VA max. @ 28V A/D max. for gold (Applicable

More information

Contents Pushbuttons. AB Series...C6 0.4VA Logic Level; Process Sealed Straight, Right Angle, & Vertical PC

Contents Pushbuttons. AB Series...C6 0.4VA Logic Level; Process Sealed Straight, Right Angle, & Vertical PC ontents Pushbuttons B Series... 0.V Logic Level; Process Sealed Straight, Right ngle, & Vertical P BB Series... ntistatic; 0.V Logic Level; Process Sealed Straight, Right ngle, & Vertical P DB Series...

More information

New Bicolor Alternating Legends

New Bicolor Alternating Legends Contact No. 17 New Bicolor KP01 & KP0, NP01 & UB eries KP01 & KP0 ERIE NP01 ERIE UB ERIE Blue LED Illumination Amber LED Illumination 013-07-05 eries KP, NP01, & UB Extensive Variety Bicolor LED Illumination

More information

Attractive rugged rocker switch

Attractive rugged rocker switch istinctive features Attractive rugged rocker switch UG0AR Removable actuator Easy to stock Easy to customize Uptodate rocker design Smooth curves Wide choice of colours and symbols Laser etched symbols

More information

3.2. Pushbuttons. For Immediate Delivery or Tech Support call KMParts.com at (866) Contents

3.2. Pushbuttons. For Immediate Delivery or Tech Support call KMParts.com at (866) Contents . Pushbuttons Product Description Eaton offers a wide range of pushbutton switches for standard industry applications such as appliances, electronics, medical and test instrumentation, office equipment

More information

Distinctive Characteristics

Distinctive Characteristics Distinctive Characteristics High insulating material for 6mm CKM models withstands over 5 kilovolts of electrostatic discharge, thus providing antistatic feature. Rugged, die cast housing 9mm CKL models

More information

General Specifications

General Specifications Series CK High Security Keylocks General Specifications Electrical Capacity (Resistive Load) Power Level: 3A @ 50V AC Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical

More information

Miniature Switches & Pilot Devices

Miniature Switches & Pilot Devices A8 Series Miniature Switches and Pilot Devices: 8mm Key features of the 21/64" (8mm) A8 series Switches and Pilot Devices include: 21/64" (8mm) round mounting hole Compact Design Saves Space Bright and

More information

Lighted Pushbutton Switch

Lighted Pushbutton Switch Lighted Pushbutton Switch General Purpose and Micro-Voltage/Current Load Switch Requires only 22 mm mounting depth All LEDs, lamps, legends and pushbutton units replaceable without tools Oil-resistant

More information

TYPICAL SWITCH ORDERING EXAMPLE TERMINALS

TYPICAL SWITCH ORDERING EXAMPLE TERMINALS Series M TYPIL SWITH ORDERIN EXMPLE M0 S 0 POLES SMLL TOLES SMLL BUSHINS ONTT MTERILS & RTINS OPTIONL PS P OLORS SPDT DPDT SPT PDT * PDT DPT * -pole available on vertical models only. IRUITS ON NONE ON

More information

8500 Series Subminiature Pushbutton Switches

8500 Series Subminiature Pushbutton Switches Subminiature Switches Features/Benefits Pre-travel or over-travel models available Ratings up to 3 AMPS Reliable contact design RoHS compliant Typical Applications Detection Telecommunications and networking

More information

General Specifications

General Specifications Series M Waterproof Miniature eneral Specifications Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical apacity (Resistive

More information

SWITCHES FOR TOUGH ENVIRONMENTS

SWITCHES FOR TOUGH ENVIRONMENTS SWITCHES FO TOUGH ENVIONMENTS Industrial & IP-ated Switches NKK Authorized Distributor Contact us for quotes or additional product info: 1.800.590.4055 http://hughespeters.com/contact/ Industrial & IP-ated

More information

ø10 A1 Series Miniature Control Units

ø10 A1 Series Miniature Control Units A1 ø10 A1 Series Miniature Control Short 22-mm-long body miniature control unit series with LED illumination face and snap-action switching. Bright and clear LED illumination. All series have terminals

More information

IL series Sealed pushbutton switches for thick panels - long bushing Ø 12 mm - momentary

IL series Sealed pushbutton switches for thick panels - long bushing Ø 12 mm - momentary Distinctive features and specifications Momentary pushbuttons for thick panels Illuminated or non-illuminated Tactile feedback Flat round actuator for optional marking Sealed to IP67 ENVIRONMENTAL SPECIFICATIONS

More information

Emergency Stop Switch A165E. Ordering Information. Mounting Aperture of 16 mm

Emergency Stop Switch A165E. Ordering Information. Mounting Aperture of 16 mm Emergency Stop Switch Mounting Aperture of 16 mm Modular construction, easy installation Positive opening mechanism with minimum contact separation of 3 mm in accordance with EN60947-5-1, Conforms to EN418

More information

2.4 Dual Motion Safety Switch /8007 EURO SR /8005 Euro Full Size /8065 ESPORT

2.4 Dual Motion Safety Switch /8007 EURO SR /8005 Euro Full Size /8065 ESPORT Rockers NGR. Introduction Product Selection Guide..................................... NGR Product Description....................................... Number Selection..................................

More information

Selection guide - Section B1 «I» range

Selection guide - Section B1 «I» range Selection guide - Section «I» range New! New! New! New! New! New! Series IC IL IM IP IB-IS IHS IHL IQ mom. & latching hall effect hall effect momentary Page -2-6 -11-15 -25-29 -32-35 Poles 1 1 1 1 1 1

More information

Series 300. Miniature Rocker & Paddle Switches

Series 300. Miniature Rocker & Paddle Switches Series 00 SPECIFICATIS: CTACT RATING: Refer to "Contact Material Options" for more info. ELECTRICAL LIFE: 0,000 make-and-break cycles at full load. CTACT RESISTANCE: 0m max. inital @ -VDC. 00mA for both

More information

ø8 A8 Series Miniature Control Units

ø8 A8 Series Miniature Control Units A8 ø8 A8 Series Miniature Control Short 22-mm-long body miniature control unit series with LED illumination face and snap-action switching. Bright and clear LED illumination. All series have terminals

More information

MINIATURE SWITCHES. Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action)

MINIATURE SWITCHES. Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action) Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action) MINIATURE SWITCHES PS SERIES 5 AMP. (S.P.) 1 AMP (D.P.) 0.4 VA DIRECT PANEL MOUNT Basic P/N Terminal Type Poles Cap

More information

SERIES SINGLE AND DOUBLE-POLE ROCKER SWITCHES

SERIES SINGLE AND DOUBLE-POLE ROCKER SWITCHES TO 1 (4) A 50 V AC PRODUCT FEATURES 100 million times proven switching principle High, fl exible design variety Excellent actuating characteristic Illuminated and non-illuminated variants ON REQUEST Other

More information

Non-illuminated Push Buttons

Non-illuminated Push Buttons Non-illuminated Push Buttons 3 Accessories for push buttons Lockout attachment Contact block kits Lens kits Wobblestick kit Push Button Cap Interchangeable, snap-in design Protective caps 9 colors: red,

More information

Snap Action Miniature Pushbutton Switches

Snap Action Miniature Pushbutton Switches Snap Action Miniature Switches SERIES 38C Miniature Switches FEATURES and Circuitry Choice of Bushings, and Terminations Caps and Frames Available UL Recoginized DIMENSIONS IN INCHES (AND MILLIMETERS)

More information

Bright illumination face and snap-action switching.

Bright illumination face and snap-action switching. ø A2 Series ø10 A1 Series ø8 A8 Series A2 Series A1 Series A8 Series Bright illumination face and snap-action switching. See website for details on approvals and standards. Hole Size Model Function Degree

More information

Indicator body single with two independent lamp bases, raised, rectangular, black plastic, screw terminals, without bezel. Part No

Indicator body single with two independent lamp bases, raised, rectangular, black plastic, screw terminals, without bezel. Part No Series 03. mm x 4. mm IP40/IP65 0 A 400 VAC Choose one component from each of the coloured sections to assemble a complete switch. For other options or further information please contact your local sales

More information

9000 SERIES SUBMINIATURE MOMENTARY PUSHBUTTON SWITCHES Overview

9000 SERIES SUBMINIATURE MOMENTARY PUSHBUTTON SWITCHES Overview A 9000 SERIES Overview 9 SERIES Number of poles 3 Single pole Electrical functions 2 Normally closed (NC) 3 Normally open (NO) Terminals, case and bushing Case height 8 (.314) 2 Straight terminals - threaded

More information

HMI Components. Series. Indicator Illuminated pushbutton Mushroom-head pushbutton Key lock switch

HMI Components. Series. Indicator Illuminated pushbutton Mushroom-head pushbutton Key lock switch Edition 10/2016 HMI Components Series Characteristics The compact Series is especially suited for: Flush design The large rectangular design (24x36mm) features a large illuminated area. Functions The Series

More information

ELECTRICAL SPECIFICATIONS

ELECTRICAL SPECIFICATIONS Distinctive features and specifications Panel and PC mount models Snap-in panel mounting version Tactile feedback ELECTRICAL SPECIFICATIONS Max. current/voltage rating with resistive load : Models for

More information

ø12 A2 Series Miniature Control Units

ø12 A2 Series Miniature Control Units ø2 A2 Series Miniature Control Short 22-mm-long body miniature control unit series with bright LED illumination face and snap-action switching. Degree of protection: IP40 and IP5 (IEC 0529) All series

More information

Functions The Series 19 incorporates the following functions: Indicator Pushbutton Illuminated pushbutton

Functions The Series 19 incorporates the following functions: Indicator Pushbutton Illuminated pushbutton Edition 11/2013 HMI-Components 19 Series Characteristics The compact 8 mm Series 19 is especially suited for: Raised design PCB (with adaptor) The low level switching element is laid out for low current

More information

CIT SWITCHTM ANT SPECIFICATIONS

CIT SWITCHTM ANT SPECIFICATIONS Wide variety of applications from consumer electronics to commercial Standard epoxy sealed terminations Gold contacts available for low power applications Available support brackets for greater stability

More information

IP series Latching action pushbutton switches for harsh environments

IP series Latching action pushbutton switches for harsh environments Latching action pushbutton switches for harsh environments Distinctive features and specifications Latching action Actuator remains in the low position when ON. Illuminated and non-illuminated Compact

More information

Attractive rugged rocker switch

Attractive rugged rocker switch istinctive features Attractive rugged rocker switch UG0AR Removable actuator Easy to stock Easy to customize Uptodate rocker design Smooth curves Wide choice of colours and symbols Laser etched symbols

More information

Sealed pushbutton switches - bushing Ø 16 mm - momentary

Sealed pushbutton switches - bushing Ø 16 mm - momentary Sealed pushbutton switches - bushing Ø 16 mm - momentary Distinctive features The IR series is a range of sealed momentary pushbutton switches with dia. 16 mm bushing. This series is divided into 2 families

More information

SPECIFICATIONS: MATERIALS: If your preferred product configuration is not shown, please contact our sales representative for custom design.

SPECIFICATIONS: MATERIALS: If your preferred product configuration is not shown, please contact our sales representative for custom design. SPECIFICATIS: CTACT RATING: Refer to "Contact Material Options" for more info. ELECTRICAL LIFE: 50,000 make-and-break cycles at full load. CTACT RESISTANCE: 0m max. initial @2-4VDC 00mA for both silver

More information

TYPICAL SWITCH ORDERING EXAMPLE. Contact Materials & Ratings. Silver Rated 125V AC & 250V AC Gold Rated 0.4VA 28V AC/DC max.

TYPICAL SWITCH ORDERING EXAMPLE. Contact Materials & Ratings. Silver Rated 125V AC & 250V AC Gold Rated 0.4VA 28V AC/DC max. Large ushing Miniature Pushbuttons Series M000 S M Poles & ircuits 0 SPDT () 06 SPDT 06 DPDT () 08 DPDT 8 PDT () 8 PDT ( ) = Momentary Plunger Type TYPIL SWITH ORDERING EXMPLE 0 S W 0 D Plunger for Screw-on

More information

Momentary pushbutton switches - round plunger

Momentary pushbutton switches - round plunger 1200 series Momentary pushbutton switches - round plunger Distinctive features and specifications Butt action contacts, double break NF (EN 61058-1), UL and CSA approved ELECTRICAL SPECIFICATIONS Max.

More information

Switches. SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY 115VAC, 28VDC)

Switches. SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY 115VAC, 28VDC) SWITCH SELECTION GUIDE Toggle Switches SERIES FEATURE ACTUATION MAX RATING SEAL RATING MOUNTING CIRCUITRY (Resistive @ 115VAC, 28VDC) T1 2 or 3 Position, Momentary, 8A MIL-PRF-83731 15/32" or 1/4" dia.

More information

IR series Sealed pushbutton switches - bushing Ø 16 mm - momentary

IR series Sealed pushbutton switches - bushing Ø 16 mm - momentary Sealed pushbutton switches - bushing Ø 16 mm - momentary Distinctive features The IR series is a range of sealed momentary pushbutton switches with dia. 16 mm bushing. This series is divided into 2 families

More information

IR series. Sealed pushbutton switches bushing Ø 16 mm momentary standard version DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS

IR series. Sealed pushbutton switches bushing Ø 16 mm momentary standard version DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS SW-IRMOM-1801 DISTINCTIVE FEATURES Screw version up to A Tactile feedback Sealed to IP6 Illuminated or non-illuminated Flat round actuator for optional marking ENVIRONMENTAL SPECIFICATIONS Front panel

More information

A165-E. Ordering Information. Emergency Stop Switch. For Panel Cutout of 16 mm

A165-E. Ordering Information. Emergency Stop Switch. For Panel Cutout of 16 mm Emergency Stop Switch For Panel Cutout of 16 mm H Modular construction, easy installation H Positive opening mechanism with a minimum contact separation of 3 mm in accordance with EN6947-5-1, for NC contacts

More information

Table of Contents. Incandescent Miniature EMI Suppressed Watertight Size T-1 3/ Incandescent Miniature Size T-1 3/

Table of Contents. Incandescent Miniature EMI Suppressed Watertight Size T-1 3/ Incandescent Miniature Size T-1 3/ Indicator Products Table of Contents DESCRIPTION PRESSLITE TYPE OPTOLITE CONTINUED PAGE NUMBER DESCRIPTION TYPE PAGE NUMBER Friction Cap Bases EMI Suppressed Alternate Action 5 Amp S.P.D.T Form 99-36980

More information

Two case lengths. Three electrical functions. Sealing options. Model X1146 with Ø 16 (.630) bushing ELECTRICAL SPECIFICATIONS.

Two case lengths. Three electrical functions. Sealing options. Model X1146 with Ø 16 (.630) bushing ELECTRICAL SPECIFICATIONS. Distinctive features and specifications Two case lengths Three electrical functions Sealing options Model X1146 with Ø 16 (.630) bushing Max. current/voltage rating with resistive load : - silver contact

More information

SERIES SINGLE AND DOUBLE-POLE PUSHBUTTON SWITCHES

SERIES SINGLE AND DOUBLE-POLE PUSHBUTTON SWITCHES PRODUCT FEATURES Illuminated and non-illuminated pushbutton switch Proven jump contact switching system (double interrupting) Opening and closing speed independent of the actuating speed Product-dependent

More information

Fuseholders PAGE. Fuseholders.

Fuseholders PAGE. Fuseholders. PAGE International Shock-Safe (Panel Mount).......................................................................... 467-468 Flip-Top Shock-Safe (Panel Mount)..................................................................................

More information

IQ series Sealed pushbutton switches - bushing Ø 16 mm - snap-in mounting

IQ series Sealed pushbutton switches - bushing Ø 16 mm - snap-in mounting Sealed pushbutton switches - bushing Ø 16 mm - snap-in mounting Distinctive features Like the IR series, the IQ series is a range of sealed pushbutton switches with dia. 16 mm bushing. But IQ pushbuttons

More information

Switches. Introduction

Switches. Introduction Introduction Switches Manufactured from, Bulgin s extensive range of vandal resistant security switches are designed with a high resistance to wear and tear, corrosion and harsh use in potentially hostile

More information

MINIATURE SWITCHES. Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action)

MINIATURE SWITCHES. Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action) Sensitive Snap-Action Pushbutton Switches Solder and P.C. Terminals (Momentary Action) MINIATURE SWITCHES PS SERIES 5 AMP. (S.P.) 1 AMP (D.P.) 0.4 VA DIRECT PANEL MOUNT ONE POLE TWO POLE Basic P/N Terminal

More information

ROTARY SWITCHES. Quality Features: LIGHTED ROTARY UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X.

ROTARY SWITCHES. Quality Features: LIGHTED ROTARY UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X. SWITCH R2 UP TO 3 POSITIONS WITH 3 OPTIONAL, INDEPENDENT LED LIGHT POSITIONS, 1.45 X.83 PANEL CUTOUT Used in the heavy equipment, marine, process control and instrumentation markets the R2 rotary switch

More information

K12 High Performance Key Switches

K12 High Performance Key Switches High Performance Features/Benefits Typical Applications Excellent tactile feel Automotive Wide choice of LE colors, Off-road transportation travel and actuator forces Industrial electronics High reliability

More information

8000 series. Momentary or alternate action pushbutton switches DISTINCTIVE FEATURES ELECTRICAL SPECIFICATIONS GENERAL SPECIFICATIONS MATERIALS

8000 series. Momentary or alternate action pushbutton switches DISTINCTIVE FEATURES ELECTRICAL SPECIFICATIONS GENERAL SPECIFICATIONS MATERIALS SW-8000-808 DISTINCTIVE FEATURES Momentary or alternate Bushing Ø 6.35 (/4) and Ø.9 (5/3) UL approved ELECTRICAL SPECIFICATIS Max. current/voltage rating with resistive load : - silver contacts : 4 A 30

More information

Various rocker colours. Illuminated or non-illuminated ELECTRICAL SPECIFICATIONS

Various rocker colours. Illuminated or non-illuminated ELECTRICAL SPECIFICATIONS 00 series istinctive features and specifications Three rocker shapes : plain, Vshaped or concave Various rocker colours Frame with protection guard on 00LP models Illuminated or nonilluminated UL, CSA,

More information

T 3965 EN Type 3965 Solenoid Valve Island To control pneumatic actuators

T 3965 EN Type 3965 Solenoid Valve Island To control pneumatic actuators T 365 EN Type 365 Solenoid Valve Island To control pneumatic actuators Application The Type 365 Solenoid Valve Island is a compact solution for the central control of pneumatic actuators in chemical and

More information

C&K 7000 Series Miniature Toggle Switches

C&K 7000 Series Miniature Toggle Switches Miniature Switches eatures/benefits Multi-pole and multi-position Wide variety of actuator and termination options Epoxy sealed terminals prevent contamination during soldering Typical Applications Telecommunications

More information

SERIES 34A Miniature Toggle Switches

SERIES 34A Miniature Toggle Switches DIP Switches Toggle Switches Series A: Miniature Toggle Switches SERIES A Miniature Toggle Switches FEATURES Save Space and Weight,, PDT, and DPT Circuitry Choice of Actuators, Bushings and Terminations

More information

JAY-EL MARK 10 P/N ILLUMINATED PUSHBUTTON SWITCH MEETS REQUIREMENTS OF MIL-S-22885

JAY-EL MARK 10 P/N ILLUMINATED PUSHBUTTON SWITCH MEETS REQUIREMENTS OF MIL-S-22885 TOP MARK 10 JAY-EL MARK 10 ILLUMINATED PUSHBUTTON SWITCH MEETS REQUIREMENTS OF MIL-S-22885 Catalog No. 7010-5 11-03 MARK 10 DESIGN FEATURES ELECTRICAL THIS SWITCH IS DESIGNED TO MEET THE EXACTING REQUIREMENTS

More information

Security Switches. Anti Vandal, Pushbutton. Specifications. Specifications S76 S77. Features.748 (19mm) bushing diameter

Security Switches. Anti Vandal, Pushbutton. Specifications. Specifications S76 S77. Features.748 (19mm) bushing diameter Anti Vandal, Pushbutton S76.287 (7.3) c: Screw (Assembled).098 (2.5) Typ.142 (3.6) Type Circuitry Action Actuator g 54 377 SPST NO OFF (ON) Stainless Steel, Flat S76b 54 378 SPST NO OFF (ON) Stainless

More information

RAFIX 22 QR. General data. Content

RAFIX 22 QR. General data. Content QR General data QR control component range For a mounting hole diameter of.3 mm to IEC 60947 50V/10A max. Water-jet proof IP65 collar shapes The lamps of the pushbuttons can also be replaced from the front

More information

IP series. Pushbutton switches for harsh environments bushing Ø 12 mm momentary DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS

IP series. Pushbutton switches for harsh environments bushing Ø 12 mm momentary DISTINCTIVE FEATURES ENVIRONMENTAL SPECIFICATIONS SW-IPMOM-1709 DISTINCTIVE FEATURES Illuminated or non-illuminated Tactile feedback Wide variety of configurations Flat round actuator for optional marking Sealed to IP67 and IP69K ENVIRONMENTAL SPECIFICATIONS

More information

C&K DA Series Miniature Single Pole Rocker Switches

C&K DA Series Miniature Single Pole Rocker Switches Features/Benefits Typical Applications Nice actuator styling with Small appliances multiple options Computers and peripherals Guards to prevent accidental Medical instrumentation actuation Momentary and

More information