Parts Manual. Manufacturing, Inc. Levee Seeder. LS10 and LS12

Transcription

1 Parts Manual LS10 and LS12 Levee Seeder Manufacturing, Inc.! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover illustration may show optional equipment not supplied with standard unit. 3)GREAT PLAINS/3-POINT DRILLS/LEVEE SEEDERS Copyright 2000 Printed 3/10/2004 Rev. A

2 Section 1 Introduction Table of Contents Table of Contents Table of Contents Section 1 Introduction General Information Using This Manual Manual Replacement Information Manual Revisions Touch-up Paint Hardware Legend Replacement Hardware Serial Numbers Part Number Service Coding Part Number Index Section 2 Box and Frame Frame Assembly Box Assembly 12 Foot (10 Foot S/N TT1139-) 2-3 Box Assembly 10 Foot (S/N TT1140+) Seed Level Indicator Lights (Option) Section 3 Metering System Feeder Cup Channel Section 4 Drive Hydraulic Drive Drive Hydraulics Section 5 Decals Decal Placement Copyright 2000 All rights Reserved Great Plains Manufacturing, Inc. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. Great Plains Manufacturing, Incorporated Trademarks The following are trademarks of Great Plains Mfg., Inc.: Application Systems, Ausherman, Land Pride, Great Plains All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 4/8/2002

3 Alphabetical Page Index B Box Assembly D Decal Placement Drive Hydraulics F Feeder Cup Channel Frame Assembly H Hydraulic Drive L Lights (Option) S Seed Level Indicator /8/2002

4 Section 1 Introduction 1-1 LS10 and LS12 Levee Seeder LS10 and LS12 Levee Seeder Table of Contents General Information Using This Manual This manual is divided into sections. The first section contains General Information, a Table of Contents, an Alphabetical Page Index, and a Part Number Index. The remaining sections divide the machine into segments (i.e. Frames, Drives, Hydraulics, etc.) which illustrate and list all parts. The Great Plains parts in this manual are specially designed for this machine and should be replaced with Great Plains parts only. The information in this manual is current at printing. Some parts may change to assure top performance. Right-hand and left-hand as used in this manual are determined by facing the direction the machine will travel while in use. Below is an example of two facing pages from a parts manual. Familiarize yourself with the contents of these pages. Manual Replacement Information Replacement manuals are available. Refer to your dealer or the Great Plains Publications Catalog for additional information. Manual Revisions When this manual is revised, the modification date is printed on the front cover and on the revised page(s). Touch-up Paint Repaint parts where paint is worn or scratched to prevent rust. Aerosol touch-up paint is available. To order use Great Plains parts numbers below: GP Green C GP Black C GP Beige C GP Buckskin C Page Number Manual Name Serial Number Break Illustration Page Parts Page Section Name 2-1 CF500 and CF600 Frames 2-2 Section Number Illustration Heading Illustration Tongue & Pull Bar (S/N ) Tongue & Pull Bar (S/N ) H 13' END WHEEL TONGUE WELDMENT H PULL BAR WELDMENT LH H PULL BAR WELDMENT RH C U-BOLT 5/8-11 X 3 17/32 UNEVEN C WASHER LOCK SPRING 5/8 PLT C NUT HEX 5/8-11 PLT C RHSNB 1/2-13X1 GR C HFSS 1/2-13X1 1/4 GR C WASHER LOCK SPRING 1/2 PLT C NUT HEX 1/2-13 PLT D SAFETY CHAIN WASHER C SPRING HOSE LOOP C SCREW HEX 3/8-16X1 TYPE F C WASHER LOCK SPRING 3/8 PLT C WASHER FLAT 3/8 SAE PLT D CLEVIS HITCH TOP HALF D CLEVIS HITCH BOTTOM HALF C RHSNB 3/4-10X2 1/2 GR C WASHER LOCK SPRING 3/4 PLT C NUT HEX 3/4-10 PLT C NUT HEX WHIZ 1/2-13 PLT C U-BOLT 1/2-13 X 3 17/32 X4 3/ C SCREW JACK 2000# C RHSNB 3/4-10X3 GR C SAFETY CHAIN LB 2 Parts List Illustration Number P 7/1/99 7/1/ P Manual Number New or Modification Date 5/15/2000

5 Introduction Hardware Legend AR BLADE C CP CPHSSS CPSHSS CPSQHSS CRFCHMS CRPHMS CRPHTFS CRRHMS CRTHMS CSNB FHMS FTC H HCLN HFLCS HFS HFSLN HFSS HHCS HSBHCS HSFCHCS HSHCS HSSS HTLN HWHCS As Required Blade Bolt Cap Screw Cotter Pin Cup Point Hex Socket Set Screw Cup Point Square Head Set Screw Cup Point Square Head Set Screw Cross Recess Flat Countersunk Head Mach. Screw Cross Recess Pan Head Machine Screw Cross Recess Pan Head Thread Forming Cross Recess Round Head Machine Screw Cross Recess Truss Head Machine Screw Countersunk Square Neck Bolt Flat Head Machine Screw Full Thread Cap Screw Hex Nut Hex Center Lock Nut Hex Flange Lock Cap Screw Hex Flange Screw Hex Flange Serrated Lock Nut Hex Flange Serrated Screw Hex Head Cap Screw or Metric Bolt Hex Socket Button Head Cap Screw Hex Socket Flat Countersunk Head Cap Screw Hex Socket Head Cap Screw Hex Socket Head Screw Hex Top Lock Nut Hex Washer Head Cap Screw Replacement Hardware The Hardware Legend above lists hardware abbreviations used in the parts lists. All bolts and nuts are grade 5 unless otherwise noted. The use of improper grades of hardware can result in personal injury, damage to equipment, or loss of property. Serial Numbers Always use the serial and model number when ordering parts. Refer to the operator s manual for serial number plate location. (S/N or Includes serial numbers S/N and above) and above (to the latest number) (S/N ) Includes serial numbers between and (S/N or Includes serial numbers S/N and below) and below (to the earliest number) HWHMS HXBHCS J JIC L LUG NFC NPSM NPTF P PHMS PLOW RHMS RHSNB SCREW LEVELING SCREW THUMB SCREW WELD SFCHMS SFHMS SP SP SCREW SQHSS SRHMS SSS STCS STHMS WHEEL WING Hex Washer Head Machine Screw Hex Socket Button Head Cap Screw Hex Jam Nut 37 Degree Tapered Thread Helical Spring Lock Washer Lug Bolt National Fine Cap Screw National Pipe Straight Mechanical National Pipe Taper Fuel Wide Plain Washer Pan Head Machine Screw Plow Bolt Round Head Machine Screw Round Head Square Neck Bolt Leveling Screw Thumb Screw Weld Screw Slotted Flat Countersunk Head Machine Screw Slotted Fillister Head Machine Screw Special Special Screw Square Head Set Screw Slotted Round Head Machine Screw Socket Set Screw Self Tapping Cap Screw Slotted Truss Head Machine Screw Wheel Studs and Hub Long Bolts Wing Bolt Part Number Service Coding Within the parts lists some part numbers are coded for revisions and interchangeability. Bold face type indicates parts that have been revised. These parts are considered interchangeable unless otherwise noted. Service Code Legend: ➊ First revision, e.g.; ➋ is 2nd revision, ➌ is 3rd revision, etc. (Greater numbers are the newest.) Use existing stock of this part before ordering the revision. Not interchangeable ➀➋ Revision 2 is not interchangeable w/1 The sample below shows how these codes are used. Not interchangeable with revision 1 Item number Revision 3 Part Number Description 1. ➀➌ A BLADE SPINDLE W/KEY 1/4SQ X7/8 ➋ D BLD SPNDL SHFT (RPBY A) Revision 2 ➊ D BLD SPNDL SHFT (RPBY A) Use up existing stock Revision 1 5/15/2000

6 1-3 LS10 and LS12 Levee Seeder LS10 and LS12 Levee Seeder Table of Contents Part Number Index Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage H H H H H H D D D D D D D D H D D D D D D H H D H D D D D D D D D D S H D D D D D D H H D H H D D D D D D S S D D D D C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C /10/2004

7 Introduction Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage Part Number aaaaaaaaapage 3/10/2004

8 Section 2L Box and Frame 2-1 LS10 and LS12 Levee Seeder LS10 and LS12 Levee Seeder Frame Assembly Table of Contents /14/2001

9 Box and Frame 2-2 Frame Assembly Ref. Part No. Part Description Comments H LADDER AND STAND WELDMENT C HHCS 1/2-13X2 3/4 GR C WASHER FLAT 1/2 SAE PLT D LADDER SPACER C HHCS 5/16-18X1 GR C WASHER FLAT 5/16 SAE PLT C WASHER LOCK SPRING 1/2 PLT C NUT HEX 1/2-13 PLT H 12 LEVEE SEEDER FRAME H 10 LEVEE SEEDER FRAME S/N TT H 10 LEVEE SEEDER FRAME S/N TT D DIVERTER SPACER TUBE C WASHER LOCK SPRING 5/16 PLT C NUT HEX 5/16-18 PLT D 12 END DIVERTER PANEL D 10 END DIVERTER PANEL D 12 CENTER DIVERTER PANEL D 10 CENTER DIVERTER PANEL C HHCS 1/2-13X1 1/4 GR C U-BOLT 5/8-11 X 3 1/32 X 4 1/ H LEVEE SEEDER MOUNT WELDMENT C WASHER LOCK SPRING 5/8 PLT C NUT HEX 5/8-11 PLT D UNIVERSAL MOUNTING BAR C NUT LOCK 5/16-18 PLT C HHCS 5/16-18X3 1/4 GR H PLOW STAND WELDMENT C PIN WIRE SNAP LOCK 3 1/2 2 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 11/14/2001

10 2-3 LS10 and LS12 Levee Seeder Box Assembly 12 Foot (10 Foot S/N TT1139-) /10/2004

11 Box and Frame 2-4 Box Assembly 12 Foot (10 Foot S/N TT1139-) Ref. Part No. Part Description Comments C HFSS 1/2-13X1 1/2 GR D HANDLE D SEED BOX IDLER COVER RH Only on 12 box 1/31/ C WASHER FLAT 3/8 USS PLT Only on 12 box C WASHER LOCK SPRING 3/8 PLT Only on 12 box C HHCS 3/8-16X1 1/4 GR5 Only on 12 box H 12 SEED BOX H 20 SEED BOX LH C HFS 5/16-18X3/4 GR D SEED BOX IDLER COVER LH Only on 12 box 1/31/ C NUT HEX FLG. LOCK 1/2-13 PLT C NUT FLANGE LOCK 3/8-16 PLT D SEED BOX PARTITION C NUT HEX FLANGE 5/16-18 PLT S LID HINGE ASSEMBLY PS25120 Includes items 11,16,17 and C HHCS 3/8-16X1 GR D LID HINGE PIVOT D LID HINGE BASE PLATE C RHSNB 3/8-16X2 GR D LATCH CASTING MACHINED C SPRING.540 O.D.X 1 1/4 X.054W D LID HANDLE C WASHER FLAT 5/16 SAE PLT C HHCS 5/16-18X1 1/4 NYL H LID /16 SEED H LID 106 SEED C NUT LOCK 5/16-18 PLT C x 90 LB GAS SPRING D BEARING CUTOUT COVER, 47 MST 2/1/ C HFSS 3/8-16X1 1/2 GR D SEED BOX REINFORCEMENT STRAP C RHSNB 5/16-18X3/4 GR H BOX PARTITION UPPER PAD 2 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 3/10/2004

12 2-5 LS10 and LS12 Levee Seeder Box Assembly 10 Foot (S/N TT1140+) /14/2001

13 Box and Frame 2-6 Box Assembly 10 Foot (S/N TT1140+) Ref. Part No. Part Description Comments H 10 LEVEE SEEDER BOX WELDMENT D SEED BOX PARTITION H 10 LID WELDMENT C x 90 LB GAS SPRING C NUT LOCK 5/16-18 PLT C NUT HEX FLANGE 5/16-18 PLT C HFS 5/16-18X3/4 GR C NUT HEX FLG. LOCK 1/2-13 PLT D HANDLE C WASHER FLAT 3/8 USS PLT C HFSS 1/2-13X1 1/2 GR C RHSNB 5/16-18X3/4 GR C WASHER FLAT 5/16 SAE PLT C NUT HEX 5/16-18 PLT S LID HINGE ASSEMBLY PS25120 Includes items 20,21.22 and D LATCH CASTING MACHINED C SPRING.540 O.D.X 1 1/4 X.054W D LID HANDLE C HHCS 5/16-18X1 1/4 NYL C NUT FLANGE LOCK 3/8-16 PLT D LID HINGE PIVOT D LID HINGE BASE PLATE C RHSNB 3/8-16X2 GR D BEARING CUTOUT COVER, 47 MST C HHCS 3/8-16X1 GR5 2 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 11/14/2001

14 2-7 LS10 and LS12 Levee Seeder Seed Level Indicator /15/2000

15 Box and Frame 2-8 Seed Level Indicator Ref. Part No. Part Description Comments C SEED LEVEL INDICATOR C SCR HEX HD SHT MET #8 X 1/ C SEED LEVEL BUSHING C DECAL LETTER E No longer available. Order part no C. 5. ➋ C DECAL SEED LEVEL LH 5 ➊ C DECAL SEED LEVEL, NOTCHED C DECAL LETTER F No longer available. Order part no C C NUT HEX PLT C WASHER INTERNAL STAR #10 PLT C HFS X 1 1/8 PLTD C SEED LEVEL ARM MOUNT H SEED LEVEL ARM, 6 3/4R. TAB C PIN COTTER 1/8 X 3/ C CABLE 3/64 X 11 5/8 W/ EYELETS D FOAM FLOAT D FOAM FLOAT WASHER C WASHER FLAT 1/4 USS PLT C NUT HEX NYLOCK 1/ C RIVET POP 1/8.125 AD42BSLF D SEED LEVEL CHAIN BRACKET 2 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 5/15/2000

16 2-9 LS10 and LS12 Levee Seeder Lights (Option) /8/2002

17 Box and Frame 2-10 Lights (Option) Ref. Part No. Part Description Comments C DUAL AG LIGHTS LH C DUAL AG LIGHTS RH D 12 EWNT LIGHT BRACKET C SCR HEX SELF TAP 1/4-20X1TYPEF D HANDLE C HFSS 1/2-13X1 1/2 GR C LIGHT HARNESS, 5 LEAD C LIGHT HARNESS, 10 WISHBONE C CABLE TIE.19X D 50LB C CABLE TIE MOUNT 2 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 4/8/2002

18 Section 3L Metering 3-1 LS10 and LS12 Levee Seeder LS10 and LS12 Levee Seeder Feeder Cup Channel Table of Contents /17/2002

19 Metering System 3-2 Feeder Cup Channel Ref. Part No. Part Description Comments D 12 LS FEEDERCUP TRAY D 10 LS FEEDERCUP TRAY S/N TT D 10 LS FEEDER CUP CHANNEL S/N TT D 10 LS FEEDERCUP SHAFT D 12 LS FEEDERCUP SHAFT C SEED CUP SLEEVE C SEED CUP ASSEMBLY Includes items 23 through C PM SEED CUP SPROCKET C 5/8 SHAFT LOCKING COLLAR C SCREW SET 5/16-18 SKT KP X 3/ C HHCS 1/4-20X3/4 GR C NUT HEX WHIZ 1/4-20 PLT S LS BEARING ASSEMBLY Includes items 16 through C HHCS 3/8-16X3/4 GR C WASHER LOCK SPRING 3/8 PLT D 6 5/8 BOX DVDER FOR 8 1/2 ROW D 10 1/2 BOX DIVIDER D 2SNT SEED BOX DIVIDER CLIP C SPKT 40B25 X.630 SQ BORE D FEEDER CUP BEARING HOUSING C BRG 30MM B X 55MM OD C SNAP RING EXT BASIC C SNAP RING INT C NUT HEX LOCK 1/4-20 FLG C HFSS 1/4-20X5/8 GR C SCR SELF TAP 8X3/8 TYPE25 BT C SEED CUP WASHER RETAINER C NYLON WASHER-SPLIT C SEED CUP LEFT HALF C SEED CUP DOOR C SEED CUP RIGHT HALF C SEED CUP ADJUSTMENT HANDLE D SHAFT COUPLER LS10 S/N TT1019+ LS12 S/N SS Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 1/17/2002

20 Section 4L Drive 4-1 LS10 and LS12 Levee Seeder LS10 and LS12 Levee Seeder Hydraulic Drive Table of Contents /14/2001

21 Drive 4-2 Hydraulic Drive Ref. Part No. Part Description Comments C HHCS 1/4-20X2 1/2 GR D FLOW CONTROL VALVE - PAINTED H HYD MOTOR AND VALVE MOUNT C WASHER LOCK SPRING 1/4 PLT C NUT HEX 1/4-20 PLT C U-BOLT 3/8-16 X 3 1/32 X C SPKT 40B12 X 1 BORE D CHAIN RL #40 76 PITCHES C HHCS 3/8-16X1 GR C WASHER LOCK SPRING 3/8 PLT C NUT HEX 3/8-16 PLT D CHAIN GUARD C HYD MOTOR EATON C HHCS 1/2-13X4 1/2 GR5 SPTHD C NO T IDLER SPKT C NUT HEX JAM 1/2-13 PLT C WASHER FLAT 1/2 SAE PLT C WASHER LOCK SPRING 1/2 PLT C NUT HEX 1/2-13 PLT C FLANGETTE 52 MST LS10 S/N TT1019+ LS12 SS C BEARING 1 BORE W/LOCK COLLAR LS10 S/N TT1019+ LS12 SS C RHSNB 5/16-18X1 GR5 LS10 S/N TT1019+ LS12 SS C WASHER FLAT 5/16 SAE PLT LS10 S/N TT1019+ LS12 SS C WASHER LOCK SPRING 5/16 PLT LS10 S/N TT1019+ LS12 SS C NUT HEX 5/16-18 PLT LS10 S/N TT1019+ LS12 SS Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 11/14/2001

22 4-3 LS10 and LS12 Levee Seeder Drive Hydraulics /1/99

23 Drive 4-4 Drive Hydraulics Ref. Part No. Part Description Comments C HH1/2R /2MNPT 7/8MORB C HH1/2R /8MORB90 3/4FJIC C HH1/2R /8MORB 7/8MORB C AD 7/8MORB 3/4FJIC C TE 3/4MJIC C HH1/2R /2MNPT 3/4FJIC 4 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 11/1/99

24 Section 5L Decals 5-1 LS10 and LS12 Levee Seeder LS10 and LS12 Levee Seeder Decal Placement Table of Contents /30/2001

25 Decals 5-2 Decal Placement Ref. Part No. Part Description Comments C DECAL AMBER REFLECTOR 2000 and below C DECAL CAUTION GENERAL INSTR C DECAL WARNING HYD PRESS LONG C DECAL GREAT PLAINS W/ LOGO 5. ➋ C DECAL GREAT PLAINS ON LOGO SML 2000 and above. 5 ➊ C DECAL GREAT PLAINS ON LOGO 1999 and below C DECAL DANGER FALLING HAZZARD C DECAL WARNING MOVING CHAIN C DECAL RED REFLECTOR 2000 and below C DECAL SEED RATE LEVEE SEEDER 10. ➋ C DECAL LOGO&GP F/STRIPE 4 X and above. 10 ➊ C DECAL GP W/ LOGO AND STRIPE 1999 and below. 11. ➋ C DECAL 3 COLOR STRIPE 2.50 WIDE 2000 and above. 11 ➊ C DECAL W/ 4 COLOR STRIPE 1999 and below. 12. ➋ C DECAL LS and above. 12 ➊ C DECAL SOLID STAND LS and below. 12 ➋ C DECAL LS and above. 12 ➊ C DECAL SOLID STAND LS and below C DECAL SLOW MOVING VEHICLE C DECAL SCRIPT SOLID STAND SMALL 2000 and above C DECAL REFLECTOR RED 1 1/2X and above C DECAL REFLECTOR AMBER 1 1/2X and above 5 Legend: ➊ = 1st revision; ➋ = 2nd revision; ➌ = 3rd revision; = use up existing stock; = not interchangeable; ➀ ➋ = for example: revision 2 is not interchangeable w/revision 1 8/30/2001