Skid Cutters AP-SC2560 & AP-SC PK Parts Manual. Copyright 2018 Printed 07/11/18

Transcription

1 Skid Cutters AP-SC2560 & AP-SC PK Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 07/11/18 Cover photo may show optional equipment not supplied with standard unit.

2 Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Cutter Assembly...6 Blade Drive 60"...6 Blade Drive 72"...8 Deck 60"...10 Deck 72"...12 Guard Chain Front S/N K Guard Chain Front S/N K Guard Chain Rear...18 Hitch Components...20 Section 3: Hydraulics...22 Hydraulic Motor 4.9 Cubic Inch Eaton ( C)...22 Hydraulic Motor 6.2 Cubic Inch Eaton ( C)...24 Hydraulic Motor 7.9 Cubic Inch Eaton ( C)...26 Motor & Hose Assembly (Eaton)...28 Spindle Hub Assembly ( C)...30 Section 4: Gearboxes...32 Flex Coupler ( C)...32 Gearbox ( C) Comer...34 Section 5: Decals...36 Decals SC Decals SC Touch-up Paints...40 Section 6: Options & Accessories...42 Gauge Wheel S/N K Gauge Wheel S/N K Hub Assembly 4-Bolt W/ Zerk & Studs ( C)...46 Large Flat Faced Couplers With Adapters Bundle...48 Motor Pressure Gauge...50 Skid Shoe Options Copyright All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

3 Alphabetized Table of Contents B D F G H K L M S Blade Drive 60"...6 Blade Drive 72"...8 Decals SC Decals SC Deck 60"...10 Deck 72"...12 Flex Coupler ( C)...32 Gauge Wheel S/N K Gauge Wheel S/N K Gearbox ( C) Comer...34 Guard Chain Front S/N K Guard Chain Front S/N K Guard Chain Rear...18 Hitch Components...20 Hub Assembly 4-Bolt W/ Zerk & Studs ( C)...46 Hydraulic Motor 4.9 Cubic Inch Eaton ( C)...22 Hydraulic Motor 6.2 Cubic Inch Eaton ( C)...24 Hydraulic Motor 7.9 Cubic Inch Eaton ( C)...26 Touch-up Paints...40 Large Flat Faced Couplers With Adapters Bundle...48 Motor & Hose Assembly (Eaton)...28 Motor Pressure Gauge...50 Skid Shoe Options...52 Spindle Hub Assembly ( C) /11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 3

4 4 AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

5 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 5

6 Blade Drive 60" Table of Contents Section 2: Cutter Assembly Applies to AP-SC AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

7 Section 2: Cutter Assembly Blade Drive 60" Table of Contents Applies to AP-SC2560 Ref. Part No. Part Description Comments Revision Dwg A H C C C C C C C Drawing Image Number CO NUT, CASTLE M30 X 2 CO COTTER PIN B6 X 60 CO BLANK WASHER BLADE BOLT KIT DISHPAN WELDMENT SPCL-HUB BLD BLT 1 1/8-12X3.44 W/.25KEY HFS 5/8-11 X 1 3/4 GR8 NUT HEX TOP LOCK 1 1/8-12 PLT NUT HEX FLANGE LOCK 5/8-11 PLT WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X25 CW SPINDLE HUB ASSY 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 7

8 Blade Drive 72" Table of Contents Section 2: Cutter Assembly Applies to AP-SC AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

9 Section 2: Cutter Assembly Blade Drive 72" Table of Contents Applies to AP-SC2572 Ref. Part No. Part Description Comments Revision Dwg A H H C C C C C C C C C C Drawing Image Number CO NUT, CASTLE M30 X 2 CO COTTER PIN B6 X 60 CO BLANK WASHER BLADE BOLT KIT GUARD WELDMENT WLDMT. DISHPAN RCR2672 HHCS 5/16-18X3/4 GR5 HHCS 3/4-10X2 GR5 BLD BLT 1 1/8-12X3.44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X29 CW GBOX RC :1 STD. DRVLN 6F FLXCPLR 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 9

10 Deck 60" Table of Contents Section 2: Cutter Assembly Applies to AP-SC AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

11 Section 2: Cutter Assembly Deck 60" Table of Contents Applies to AP-SC2560 Ref. Part No. Part Description Comments Revision Dwg D H C C C Drawing Image Number BLADE BOLT ACCESS COVER DECK 60" NUT WING 3/8-16 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 11

12 Deck 72" Table of Contents Section 2: Cutter Assembly Applies to AP-SC AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

13 Section 2: Cutter Assembly Deck 72" Table of Contents Applies to AP-SC2572 Ref. Part No. Part Description Comments Revision Dwg D H C C C Drawing Image Number BLADE BOLT ACCESS COVER DECK 72" NUT WING 3/8-16 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 13

14 Guard Chain Front S/N K- Section 2: Cutter Assembly AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

15 Guard Chain Front S/N K- Section 2: Cutter Assembly Ref. Part No. Part Description Comments Revision Dwg K K D D D D C C C C Drawing Image Number FRONT CHAIN GUARD FRONT CHAIN GUARD FRONT CHAIN GUARD MOUNT FRONT CHAIN GUARD MOUNT CHAIN RETAINER CHAIN RETAINER HHCS 3/8-16X3 GR5 NUT HEX WHIZ 3/8-16 PLT WASHER FLAT 3/8 SAE PLT CHAIN WELD 5/16 GR 43 X 7-LINK AP-SC2560 AP-SC2572 AP-SC2560 AP-SC2572 AP-SC2560 AP-SC /11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 15

16 Guard Chain Front S/N K+ Section 2: Cutter Assembly AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

17 Guard Chain Front S/N K+ Section 2: Cutter Assembly Ref. Part No. Part Description Comments Revision Dwg D D K K D D C Drawing Image Number CHAIN RETAINER CHAIN RETAINER CHAIN GUARD FRONT GUARD FRONT CHAIN GUARD 60" GUARD FRONT CHAIN WELD 5/16 GR 43 X 7-LINK SC2560 SC2572 SC2560 SC2572 SC2560 SC /11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 17

18 Guard Chain Rear Table of Contents Section 2: Cutter Assembly AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

19 Guard Chain Rear Section 2: Cutter Assembly Ref. Part No. Part Description Comments Revision Dwg K K D D D D C C C C Drawing Image Number REAR DOUBLE CHAIN GUARD REAR GUARD ASSY REAR DOUBLE CHAIN MOUNT REAR DOUBLE CHAIN MOUNT CHAIN RETAINER CHAIN RETAINER HHCS 3/8-16X3 GR5 NUT HEX WHIZ 3/8-16 PLT WASHER FLAT 3/8 SAE PLT CHAIN WELD 5/16 GR 43 X 7-LINK AP-SC2560 AP-SC2572 AP-SC2560 AP-SC2572 AP-SC2560 AP-SC /11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 19

20 Hitch Components Section 2: Cutter Assembly AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

21 Hitch Components Section 2: Cutter Assembly Ref. Part No. Part Description Comments Revision Dwg K K S D D D D D H D C C C C C C C C C C C C C Image No. FLOAT CHAIN ASSEMBLY FLOAT CHAIN ASSEMBLY MANUAL CONTAINER KIT, 1 1/4 FLOAT CHAIN 3/8 PROOF FLOAT CHAIN 3/8 PROOF CHAIN CLEVIS 7/16-1/2MID LINK CHAIN COVER CHAIN COVER SC25 SERIES HITCH WELDEMENT HEIGHT ADJ. CHAIN HHCS 1/4-20X1 1/4 GR5 NUT HEX FLANGE LOCK 3/4-10 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT WASHER FLAT 3/4 USS PLT PIN COTTER 5/16 X 2 1/2 PIN CLVS.50X1.52 USBL PIN ROLL 3/8 X 2 PLT PIN COTTER 1/8 X 1 PIN CLVS HDLS 1.0X3.23 USBL MANUAL STORAGE CONTAINER PLASTIC END CAP 3X2X3/16 WL TB QUICK LINK 1/2" AP-SC2560 AP-SC2572 AP-SC2560 AP-SC2572 AP-SC2560 AP-SC /11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 21

22 Hydraulic Motor 4.9 Cubic Inch Eaton ( C) Section 3: Hydraulics AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

23 Hydraulic Motor 4.9 Cubic Inch Eaton ( C) Section 3: Hydraulics No Parts List associated with this diagram 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 23

24 Hydraulic Motor 6.2 Cubic Inch Eaton ( C) Section 3: Hydraulics AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

25 Hydraulic Motor 6.2 Cubic Inch Eaton ( C) Section 3: Hydraulics No Parts List associated with this diagram 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 25

26 Hydraulic Motor 7.9 Cubic Inch Eaton ( C) Section 3: Hydraulics AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

27 Hydraulic Motor 7.9 Cubic Inch Eaton ( C) Section 3: Hydraulics No Parts List associated with this diagram 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 27

28 Motor & Hose Assembly (Eaton) Section 3: Hydraulics AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

29 Motor & Hose Assembly (Eaton) Section 3: Hydraulics Ref. Part No. Part Description Comments Revision Dwg D C C C C C C C C C C C C C C C C C C C C C C A A A Image No. ADAPTOR SAE C 4 BOLT TO SAE A HHCS 1/2-13X1 3/4 GR5 HHCS 1/2-13X2 GR5 NUT HEX 1/2-13 PLT WASHER LOCK SPRING 1/2 PLT VALVE 3/4 IN-LINE CHECK AD 1 1/16MORB 1 1/16MJIC EL 90 9/16MJIC 7/16MORB GASKET - MOTOR GASKET SAE A 2 BOLT CP 3/8 FEMALE QD 3/8FNPT HH3/8R /8MNPT9/16FJIC HH3/4R FJIC MORB HH3/4R FJIC(1)90 TEE 1.06FJIC 1.06MJIC 1.06MJIC HYD MOTOR 4.9 CUIN/REV HYD MOTOR 6.2 CUIN/REV HYD MOTOR 7.9 CUIN/REV 1.06 AD 1 1/16FJIC 1 1/16MJIC CUP 1 1/16FORB MALE QUICK CPLR RPBY C CUP 1 1/16FORB FML QUICK CPLR RPBY C HYD MOTOR BUNDLE GPM HYD MOTOR BUNDLE GPM HYD MOTOR BUNDLE GPM Obsolete Obsolete 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 29

30 Spindle Hub Assembly ( C) Applies to AP-SC2560 Section 3: Hydraulics AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

31 Spindle Hub Assembly ( C) Section 3: Hydraulics Applies to AP-SC2560 Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number CO NUT, CASTLE M30 X 2 CO BLANK WASHER CO SEAL RETAINER CO SEAL CO COTTER PIN B6 X 60 CO SPLINE SHAFT CO BEARING CO SPINDLE HOUSING CO OIL PLUG 3/8 CO BEARING RTA25 CO NUT LOCK M45 X 1.5 CO NUT LOCK M45 X 1.5 SPINDLE HUB ASSY Beige 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 31

32 Flex Coupler ( C) Applies to AP-SC2572 Section 4: Gearboxes AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

33 Flex Coupler ( C) Section 4: Gearboxes Applies to AP-SC2572 Ref. Part No. Part Description Comments Revision Dwg C PE Drawing Image Number FLEX-COUPLER X * EC CONNECTION HUB EC WSH. BD. 35mmO.D/16.5mmI.D EC BOLT BUSHING EC CONNECTION HUB EC RUBBER DISC EC BOLT EC NUT EC WASHER 29.8mmO.D/17.2mmI.D CONICAL DOG KIT 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 33

34 Gearbox ( C) Comer Applies to AP-SC2572 Section 4: Gearboxes AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

35 Gearbox ( C) Comer Section 4: Gearboxes Applies to AP-SC2572 Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number GEARBOX COMER * CO INPUT SHAFT CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING RTA25 CO BOLT M8X22 HHB CO PINION Z18 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X2.5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X1.5 CO GEAR CROWN Z22 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY REP BY CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 61.7 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 35

36 Decals SC2560 Table of Contents Section 5: Decals Applies to AP-SC AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

37 Section 5: Decals Decals SC2560 Table of Contents Applies to AP-SC2560 Ref. Part No. Part Description Comments Revision Dwg C C C C C C C C C C C C Image No. DECAL FLAG DECAL AMBER REFLECTOR DECAL GREASE 25HRS BLACK/WHITE DECAL DANGER ROTATE BLADE DECAL WARNING PINCH POINT GEN DECAL SAFETY COMBO SUNWEST DECAL WARNING HIGH PRESSURE DECAL DO NOT OPERATE DECAL DANGER GUARD MISSING DECAL SC BLADE ROTATION DECAL KUBOTA 22" DECAL SC2560 WHITE 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 37

38 Decals SC2572 Table of Contents Section 5: Decals Applies to AP-SC AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

39 Section 5: Decals Decals SC2572 Table of Contents Applies to AP-SC2572 Ref. Part No. Part Description Comments Revision Dwg C C C C C C C C C C C C C C Image No. DECAL FLAG DECAL AMBER REFLECTOR DECAL GREASE 25HRS BLACK/WHITE DECAL DANGER PD GUARD MISS SML DECAL DANGER PTO DRIVELINE DECAL DANGER ROTATE BLADE DECAL WARNING PINCH POINT GEN DECAL SAFETY COMBO SUNWEST DECAL WARNING HIGH PRESSURE DECAL DO NOT OPERATE DECAL DANGER GUARD MISSING DECAL SC BLADE ROTATION DECAL KUBOTA 22" DECAL SC2572 WHITE 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 39

40 Touch-up Paints Section 5: Decals No diagram associated with this Parts List 40 AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

41 Touch-up Paints Section 5: Decals Ref. Part No. Part Description Comments Revision C CTU CQT CGL GLOSS BLACK SPRAY CAN GLOSS BLACK TOUCH-UP 5OZ GLOSS BLACK QUART GLOSS BLACK GALLON All Products 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 41

42 Gauge Wheel S/N K- Section 6: Options & Accessories AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

43 Gauge Wheel S/N K- Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg A H D H H H C C C C C C C C C C C C C C C C C C C C C C C C C C C C N/A C C C C C C C C Drawing Image Number GAUGE WHEEL ASSEMBLY * LOWER PARALLEL ARM WLDMNT PIVOT BUSHING GAUGE WHEEL YOKE MOUNT UPPER ARM WELDMENT GUAGE WHEEL MOUNT GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 X 90-DEG GREASE ZERK 1/4-28 THD FORMING HHCS 3/8-16X3 GR5 HUB STUD 1/2-20X1 5/8 GR5 HHCS 5/8-11X5 1/2 GR5 HHCS 3/4-10X7 1/2 GR5 HHCS 1/2-20X1 1/4 GR5 HHCS 1/2-13X3 3/4 GR8 NUT HEX 1/2-13 PLT NUT HEX 5/8-11 PLT NUT LOCK 3/4-10 PLT NUT HEX WHIZ 3/8-16 PLT NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX 1 1/4-7(MACHINED)PLAIN NUT HEX FLG/LK 1/2-20 PLT GR G WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER FLAT 1/2 USS PLT WASHER MACH 2.25 X 1.50 X 14GA PIN, HAIR COTTER 3/16 WIRE DIA PIN CLVS 1.0X3.20 USBL PIN ROLL 3/8 X 2 1/2 PLT TIRE & WHEEL LAMINATED 4.0 X 8 LAM 4X8 TR-WL-HUB-YOKE 25 SER. HUB & SPINDLE ASSY 4 BOLT HUB 4 BLT W/CUPS, ZERK & STUDS HUB 4BLT DUCTILE(USE C) OIL SEAL DBL LIP BORE BRG 1.25ID CONE BRG CUP 2.44OD BUSHING TW 1.25ODX.78IDX5 1/4 BUSHING CYL 1 1/4 X 1 X 1 RATCHET JACK - HEAVY DUT RC25 TAILWHEEL YOKE, 1.5 SHAFT RC25 TAILWHEEL YOKE, 1.5 SHAFT 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 43

44 Gauge Wheel S/N K+ Section 6: Options & Accessories AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

45 Gauge Wheel S/N K+ Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg A D H H H H C C C C C C C C C C C C C C C C C C C C C C C C Image No. GAUGE WHEEL FRONT * PIVOT BUSHING GAUGE WHEEL YOKE MOUNT GUAGE WHEEL MOUNT UPPER ARM LOWER ARM GREASE ZERK 1/4-28 X 90-DEG GREASE ZERK 1/4-28 THD FORMING HHCS 5/8-11X5 1/2 GR5 HHCS 3/4-10X7 1/2 GR5 HHCS 1/2-20X1 1/4 GR5 HHCS 1/2-13X3 3/4 GR8 NUT HEX 1/2-13 PLT NUT HEX 5/8-11 PLT NUT LOCK 3/4-10 PLT NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX FLG/LK 1/2-20 PLT GR G WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER FLAT 1/2 USS PLT WASHER MACH 2.25 X 1.50 X 14GA PIN, HAIR COTTER 3/16 WIRE DIA PIN CLVS 1.0X3.20 USBL PIN ROLL 3/8 X 2 1/2 PLT TIRE & WHEEL LAMINATED 4.0 X 8 HUB & SPINDLE ASSY 4 BOLT GRIP HANDLE.84 ID X 4 LG BUSHING CYL 1 1/4 X 1 X 1 RATCHET JACK - HEAVY DUT RC25 TAILWHEEL YOKE, 1.5 SHAFT Includes items 21 & 22 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 45

46 Hub Assembly 4-Bolt W/ Zerk & Studs ( C) Section 6: Options & Accessories AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

47 Hub Assembly 4-Bolt W/ Zerk & Studs ( C) Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg C C C C C C C C C C Image No. GREASE ZERK STRAIGHT 1/4-28 HUB STUD 1/2-20X1 5/8 GR5 NUT HEX 1 1/4-7(MACHINED)PLAIN HUB & SPINDLE ASSY 4 BOLT HUB 4 BLT W/CUPS, ZERK & STUDS HUB 4BLT DUCTILE(USE C) OIL SEAL DBL LIP BORE BRG 1.25ID CONE BRG CUP 2.44OD BUSHING TW 1.25ODX.78IDX5 1/4 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 47

48 Large Flat Faced Couplers With Adapters Bundle Section 6: Options & Accessories AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

49 Large Flat Faced Couplers With Adapters Bundle Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg A C C C Image No. LG FLAT FACED CPLRS W/ADAPTERS * AD 1 5/16MORB 1 1/16FORB CP 1 5/16FORB FEMALE QD CP 1 5/16FORB MALE QD 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 49

50 Motor Pressure Gauge Section 6: Options & Accessories AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

51 Motor Pressure Gauge Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg K C C C C Image No. MOTOR PRESSURE KIT * AD 9/16FJIC 1/4FNPT TE1 1/16MJIC 1 1/16FJIC 9/16MJ HH3/4R FJIC1SWPT90 PRESSURE GUAGE PSI 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 51

52 Skid Shoe Options Section 6: Options & Accessories AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

53 Skid Shoe Options Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg A A D D C C C C Image No. SKID SHOE BUNDLE SKID SHOE HEAVY BUNDLE * SKID SHOE SKID SHOE HEAVY PLOW 3/8-16X1 1/4 GR5 NUT LOCK 3/8-16 PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 53

54 Table of Contents The is a numeric index of all part numbers included in this manual. The index shows what page(s) the part is used on. Part Number Page Part Number Page Part Number Page Part Number Page , , 9, 31, D D...11, H A...7, H D...43, A H...43, H K K K K K K S H D D D...15, 17, D D D D D D...15, 17, D D D H...43, A A A H A A H K H K H H A K A H D D D D , , , 9, 31, , 9, 31, , , C...43, C...43, C...43, C C...15, 19, C C C C...43, C C...43, C...7, C...43, C...43, C C C...43, C C...29, 43, C...43, C...43, C...7, C C...15, 19, C...11, C C...7, 43, C...43, C C...43, C C C... 11, 13, 15, 19, 43, C...11, 13, C...29, 43, C...43, C...43, C C...43, C...7, C C...43, C...43, C C C...43, C C C C C C C C C C C...43, C C...43, 45, C...43, C C C...43, C C C C C...37, C...37, C...37, C C C...37, C...37, C...37, C...37, C C C CGL CQT CTU C...43, C...43, C...7, C...9, C...9, C...43, C...37, C C C C C C C C C...37, C...37, C C C C C C C C...37, C C C...43, C...43, C...15, 17, C C...43, 45 Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg N/A...43 PE AP-SC2560 & AP-SC2572 Skid Cutters PK 07/11/18

55 This Page Intentionally Left Blank 07/11/18 AP-SC2560 & AP-SC2572 Skid Cutters PK 55

56