Rotary Cutters RC(M)3615 S/N P Parts Manual. Copyright 2018 Printed 07/10/18

Transcription

1 Table of Contents Rotary Cutters RC(M)3615 S/N P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 07/10/18 Cover photo may show optional equipment not supplied with standard unit.

2 Table of Contents Table of Contents Section 1: Introduction...6 Using This Manual...6 Manual Replacement Information...6 Manual Revisions...6 Touch-up Paint...6 Hardware Legend...7 Replacement Hardware...7 Serial Numbers...7 Part Number Service Coding...7 Section 2: Decks & Hitches...8 Blade Carrier...8 Deck Center Section...10 Deck Wing Section...14 Hitch Ball Coupler...16 Hitch Bar Tite...18 Hitch LP Performance S/N Hitch Main Frame...22 Hitch Pintel...24 Hitch Standard Pivoting Clevis...26 Hitch Swivel...28 Leveling Rod & Wing Turnbuckle...30 Section 3: Axles...32 Axle Center S/N Axle Center S/N Axle Wing S/N Axle Wing S/N Section 4: Guards...40 Guards Chain Double Row Front...40 Guards Chain Double Row Rear...42 Guards Chain Single Row Front...44 Guards Chain Single Row Rear...46 Guards Rubber Front...48 Guards Rubber Rear...50 Section 5: Drivelines (1000 RPM)...52 Driveline Center ( C) Comer...52 Driveline Center ( C) Comer...54 Driveline Center 1000 RPM ( C) Eurocardan...56 Driveline Conv RPM ( C) Walterscheid...58 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler...60 Driveline CV 1000 RPM ( C) Weasler (S/N )...62 Driveline CV 1000 RPM ( C) Weasler...64 Driveline Slip Clutch (229829X0) Walterscheid...66 Driveline Slip Clutch 1000 RPM ( ) Eurocardan...68 Driveline Slip Clutch 1000 RPM ( ) Eurocardan...70 Driveline Slip Clutch 540/1000 RPM ( ) EC...72 Driveline Wing ( C) Eurocardan...74 Driveline Wing ( C) Walterscheid...76 Driveline Wing ( C) Comer...78 Driveline Wing ( C) Comer...80 Driveline Wing ( C) Comer...82 Driveline Wing ( C) Walterscheid...84 Section 5: Drivelines (540 RPM)...86 Driveline Center ( C) Comer...86 Driveline Center ( C) Comer...88 Driveline Center 540 RPM ( C) Eurocardan...90 Driveline Conv. 540 RPM ( C) Walterscheid...92 Driveline CV 540 RPM ( C) Weasler...94 Driveline CV 540 RPM ( C) Weasler...96 Driveline Slip Clutch (229829X0) Walterscheid...98 Driveline Slip Clutch 540/1000 RPM ( ) EC Driveline Wing ( C) Eurocardan Driveline Wing ( C) Walterscheid Driveline Wing ( C) Comer Driveline Wing ( C) Walterscheid Driveline Wing ( C) Comer Driveline Wing ( C) Comer Driveline Wing ( C) Walterscheid Section 6: Gearboxes (1000 RPM) Gearbox Center Deck (1000 RPM) ( C) Comer S/N Gearbox Divider 1000 RPM ( C) Comer Gearbox Divider 1000 RPM ( C) OMN Gearbox Divider 1000 RPM ( C) SD Engineering.122 Gearbox Left Deck 1000 RPM ( C) Comer (S/N ) Gearbox Right Deck 1000 RPM ( C) Comer (S/N ) Section 6: Gearboxes (540 RPM) Gearbox Center & Left Deck (540 RPM ) ( C) Comer S/N Gearbox Divider 540 RPM ( C) Comer Gearbox Divider 540 RPM ( C) SD Engineering..132 Gearbox Right Deck 540 RPM ( C) Comer (S/N ) Section 7: Hydraulics Hydraulic Cylinder ( C) Cross Hydraulic Cylinder ( C) Midway Hydraulic Cylinder ( C) Red Lion Hydraulic Cylinder ( C) Midway Hydraulic Cylinder ( C) Red Lion Hydraulic Lift Components Section 8: Decals Decal Placement Touch-up Paints Section 9: Options & Accessories Hydraulic Independent Wing Control Accessory Copyright All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RC(M)3615 S/N Rotary Cutters P 07/10/18

3 Table of Contents Table of Contents (continued) Manual Winch Wing Deck Tire Options /10/18 RC(M)3615 S/N Rotary Cutters P 3

4 Table of Contents Alphabetized Table of Contents A B D G Axle Center S/N Axle Center S/N Axle Wing S/N Axle Wing S/N Blade Carrier...8 Decal Placement Deck Center Section...10 Deck Wing Section...14 Driveline Center ( C) Comer...52 Driveline Center ( C) Comer...86 Driveline Center ( C) Comer...54 Driveline Center ( C) Comer...88 Driveline Center 1000 RPM ( C) Eurocardan...56 Driveline Center 540 RPM ( C) Eurocardan...90 Driveline Conv RPM ( C) Walterscheid...58 Driveline Conv. 540 RPM ( C) Walterscheid...92 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler...60 Driveline CV 1000 RPM ( C) Weasler (S/N )...62 Driveline CV 1000 RPM ( C) Weasler...64 Driveline CV 540 RPM ( C) Weasler...94 Driveline CV 540 RPM ( C) Weasler...96 Driveline Slip Clutch (229829X0) Walterscheid...66 Driveline Slip Clutch (229829X0) Walterscheid...98 Driveline Slip Clutch 1000 RPM ( ) Eurocardan...68 Driveline Slip Clutch 1000 RPM ( ) Eurocardan...70 Driveline Slip Clutch 540/1000 RPM ( ) EC...72 Driveline Slip Clutch 540/1000 RPM ( ) EC Driveline Wing ( C) Eurocardan...74 Driveline Wing ( C) Eurocardan Driveline Wing ( C) Walterscheid...76 Driveline Wing ( C) Walterscheid Driveline Wing ( C) Comer...78 Driveline Wing ( C) Comer Driveline Wing ( C) Walterscheid Driveline Wing ( C) Comer...80 Driveline Wing ( C) Comer Driveline Wing ( C) Comer...82 Driveline Wing ( C) Comer Driveline Wing ( C) Walterscheid...84 Driveline Wing ( C) Walterscheid Gearbox Center & Left Deck (540 RPM ) ( C) Comer S/N Gearbox Center Deck (1000 RPM) ( C) Comer S/N Gearbox Divider 1000 RPM ( C) Comer Gearbox Divider 1000 RPM ( C) OMN Gearbox Divider 1000 RPM ( C) SD Engineering.122 Gearbox Divider 540 RPM ( C) Comer H L M T Gearbox Divider 540 RPM ( C) SD Engineering..132 Gearbox Left Deck 1000 RPM ( C) Comer (S/N ) Gearbox Right Deck 1000 RPM ( C) Comer (S/N ) Gearbox Right Deck 540 RPM ( C) Comer (S/N ) Guards Chain Double Row Front...40 Guards Chain Double Row Rear...42 Guards Chain Single Row Front...44 Guards Chain Single Row Rear...46 Guards Rubber Front...48 Guards Rubber Rear...50 Hitch Ball Coupler...16 Hitch Bar Tite...18 Hitch LP Performance S/N Hitch Main Frame...22 Hitch Pintel...24 Hitch Standard Pivoting Clevis...26 Hitch Swivel...28 Hydraulic Cylinder ( C) Cross Hydraulic Cylinder ( C) Midway Hydraulic Cylinder ( C) Red Lion Hydraulic Cylinder ( C) Midway Hydraulic Cylinder ( C) Red Lion Hydraulic Independent Wing Control Accessory Hydraulic Lift Components Touch-up Paints Leveling Rod & Wing Turnbuckle...30 Manual Winch Wing Deck Tire Options RC(M)3615 S/N Rotary Cutters P 07/10/18

5 Table of Contents This Page Intentionally Left Blank 07/10/18 RC(M)3615 S/N Rotary Cutters P 5

6 Table of Contents 6 RC(M)3615 S/N Rotary Cutters P 07/10/18

7 Table of Contents 07/10/18 RC(M)3615 S/N Rotary Cutters P 7

8 Blade Carrier Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

9 Section 2: Decks & Hitches Blade Carrier Table of Contents Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg D D D D H N/A C C C C C C A Drawing Image Number BLADE SPACER 16 GA..064 Thick BLADE SPACER 18 GA..052 Thick BLADE SPACER 20 GA..04 Thick BLADE SPACER 24GA..03 Thick 15 DISHPAN WLDMT LG.HUB(COMER) ASSY. BLADE CARRIER LH. BLADE BOL 1 1/8-12X3 7/16 W/KY NUT HEX TOP LOCK 1 1/8-12 PLT. WASHER FLAT 1" HARDENED CUTTER BLADE 1/2 X 4 X 31 CCW CUTTER BLADE 1/2 X 4 X 25 CCW CUTTER BLADE 1/2 X 4 X 25 CW BLADE BOLT KIT As Required S/N As Required S/N As Required S/N As Required S/N Center Deck Right Deck Left Deck 07/10/18 RC(M)3615 S/N Rotary Cutters P 9

10 Table of Contents Deck Center Section Applies to RC3615 S/N , RCM3615 S/N Section 2: Decks & Hitches RC(M)3615 S/N Rotary Cutters P 07/10/18

11 Table of Contents Deck Center Section Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg H H H D H H H H H H H H H H K C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C Drawing Image Number WLDMT. SHIELD BRACKET WLDMT. SKID SHOE RH. WLDMT. SKID SHOE LH. SHIELD DIVIDER BOX DECK CENTER DECK CENTER GREEN DECK CENTER ORANGE DECK CENTER RED DECK CENTER W/DR DECK CENTER W/DR GREEN DECK CENTER W/DR ORANGE DECK CENTER W/DR RED CYLINDER SPRING BASE CYLINDER SPRING BASE 29" TIRES GEARBOX SHIELD ASSY HHCS 1/4-20X1 GR5 HHCS M8X25X20 GR8.8 HHCS 5/8-11X2 GR5 HHCS 3/4-10X2 1/4 GR5 HHCS 3/4-10X6 GR5 RHSNB 1/2-13X1 1/4 GR5 HHCS 1-8X5 GR5 HHCS M8X25X45 GR8.8 HHCS M8X25X55 GR8.8 NUT LOCK 3/4-10 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLG. LOCK 1/2-13 PLT. NUT HEX NYLOCK 1/4-20 NUT HEX FLANGE LOCK 5/8-11 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER FLAT 1/4 SAE PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 3/4 SAE PLT SPRING HOSE LOOP SPRING COMP 88OD x.362w MANUAL STORAGE CONTAINER KNOB 3/8-16 FEMALE THD 2 3/8OD PTO INT. CAT.4 540W/CLUTCH PTO INT. CAT W/CLUTCH PTO E60 X NM CLUTCH PTO E60 X NM CLUTCH DIV. OMNI/CO 540RPM SU DIVIDER OMNI/CO 1000RPM RD GBOX RC :47 STD. GBOX RC :1 STD. COMER U DIPSTICK COMER VENT # DRVLN C CV RPBY C PTO 2500 X NO CLUTCH PTO 2500 CAT /8-21 DRVLN C CV Without Deck Rings With Deck Rings Use With 29" Tires Started Using S/N RC3615 RCM3615 S/N S/N RC(M)3615 RC3615 RCM3615 RC3615 RCM3615 RC3615 S/N RC3615 S/N (Obsolete) RC3615 RCM3615 RCM3615 S/N /10/18 RC(M)3615 S/N Rotary Cutters P 11

12 Table of Contents Deck Center Section (continued) Applies to RC3615 S/N , RCM3615 S/N Section 2: Decks & Hitches Ref Part No C C C Part Description RPBY C DRVLN C CV ORCLTCH PLUG LP 3" ID RUBBER Comments RCM3615 S/N (Obsolete) RCM3615 Revision 12 RC(M)3615 S/N Rotary Cutters P 07/10/18

13 Table of Contents Deck Center Section (continued) Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N This Page Intentionally Left Blank 07/10/18 RC(M)3615 S/N Rotary Cutters P 13

14 Table of Contents Deck Wing Section Applies to RC3615 S/N , RCM3615 S/N Section 2: Decks & Hitches RC(M)3615 S/N Rotary Cutters P 07/10/18

15 Table of Contents Deck Wing Section Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg D D D H H H H H H H H H H H H H H H H H C C C C C C C C C C C C C C C C C C C C C C Drawing Image Number SKID SHOE DEFLECTOR RH DEFLECTOR LH DECK RH WING DECK RH WING GREEN DECK RH WING ORANGE DECK RH WING RED DECK RH WING W/DR DECK RH WING W/DR GREEN DECK RH WING W/DR ORANGE DECK RH WING W/DR RED DECK LH WING DECK LH WING GREEN DECK LH WING ORANGE DECK LH WING RED DECK LH WING W/DR DECK LH WING W/DR GREEN DECK LH WING W/DR ORANGE DECK LH WING W/DR RED HINGE ROD HHCS M8X25X20 GR8.8 HHCS 3/8-16X1 1/2 GR5 HHCS 3/4-10X2 1/4 GR5 RHSNB 3/8-16X1 1/4 GR5 PLOW 3/8-16X1 1/4 GR5 NUT HEX 3/8-16 PLT NUT HEX WHIZ 3/8-16 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER LOCK SPRING 3/8 PLT DRVLN C FX CLTCH PTO CAT.4 W/CLUTCH 1 3/4-20 PTO CAT.5 W/CLUTCH 1 3/4-20 RPBY C LARGE SHAFT CONE W ACCESS DOOR GBOX RC :47 STD. GBOX RC :21 STD. GBOX RC :47 REV. GBOX RC :21 REV. COMER U DIPSTICK PLUG LP 3" ID RUBBER Without Deck Rings With Deck Rings Without Deck Rings With Deck Rings S/N S/N RC3615 & RCM3615 S/N RC3615 & RCM3615 S/N RC3615 & RCM3615 LH Deck RC3615 LH Deck RCM3615 RH Deck RC3615 RH Deck RCM /10/18 RC(M)3615 S/N Rotary Cutters P 15

16 Hitch Ball Coupler Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

17 Table of Contents Hitch Ball Coupler Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A H C C C C Drawing Image Number 2 5/16" BALL HITCH ASSEMBLY * 2 5/16" BALL HITCH WELDMENT HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT S/N S/N S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 17

18 Hitch Bar Tite Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

19 Section 2: Decks & Hitches Hitch Bar Tite Table of Contents Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A H H H D D H C C C C C C C C C C C C C C C C C C C K Drawing Image Number BAR TITE HITCH * SHAFT WELDMENT WELDMENT HITCH CLEVIS SWIVEL RECEIVER HITCH WEAR PLATE WIDE FORMED HITCH SUPPORT WIDE BAR TITE WIDE TOP GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 3/4-10X6 GR5 HHCS 3/4-10X5 1/2 GR5 HHCS 1-8X6 1/2 GR5 HHCS 1-8X5 1/2 GR5 HHCS 1-8X5 GR5 NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 3/4-10 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER FLAT 50 HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING 50ODX00IDX25 BAR TITE HITCH WIDE S/N S/N S/N + S/N - S/N + S/N - S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 19

20 Table of Contents Hitch LP Performance S/N Applies to RC3615 S/N , RCM3615 S/N Section 2: Decks & Hitches RC(M)3615 S/N Rotary Cutters P 07/10/18

21 Table of Contents Hitch LP Performance S/N Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A H H H C C C C C C C C C C C C D Image No. LP PERFORMANCE HITCH SWIVEL RECEIVER HITCH CLEVIS HITCH YOKE GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X7 GR5 HHCS 3/8-16X1 1/4 GR5 NUT HEX COUPLER 3/8-16X1 3/4 NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT WASHER LOCK SPRING 3/8 PLT PIN COTTER 1/4 X 2 1/2 PLT BUSHING 1 1/4X1X1/2 HRD BUSHING 1 1/4X1X5/8 HITCH HOLDER If you order this part you will receive the updated version. You will also need to order item 16 to go with the updated item 2 If you order this part you will receive the updated version 07/10/18 RC(M)3615 S/N Rotary Cutters P 21

22 Hitch Main Frame Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

23 Table of Contents Hitch Main Frame Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg H C C C C C C C Drawing Image Number HITCH GREASE ZERK 1/4-28 THD FORMING HHCS 1-8X2 1/2 GR5 HHCS 1-8X5 GR5 NUT HEX TOP LOCK 1-8 PLT WASHER FLAT 1 USS PLT SAFETY CHAIN LB SIDEWIND JACK 5000 LB 07/10/18 RC(M)3615 S/N Rotary Cutters P 23

24 Hitch Pintel Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

25 Section 2: Decks & Hitches Hitch Pintel Table of Contents Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg A H C C C C C C C Drawing Image Number PINTLE HITCH * PINTLE RECEIVER HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HFS 5/8-11X2 1/2 GR8 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX WHIZ 5/8-11 PLT PINTLE HOOK SQ.BASE BDB S/N S/N S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 25

26 Table of Contents Hitch Standard Pivoting Clevis Applies to RC3615 S/N , RCM3615 S/N Section 2: Decks & Hitches RC(M)3615 S/N Rotary Cutters P 07/10/18

27 Table of Contents Hitch Standard Pivoting Clevis Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A D H H C C C C C C Drawing Image Number STANDARD HITCH * SPACER HITCH CLEVIS WELDMENT YOKE HITCH 3615 HHCS 5/8-11X1 3/4 GR5 HHCS 1-8X9 GR5 HHCS 5/8-11X8 1/2 GR5 NUT LOCK 5/8-11 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT 07/10/18 RC(M)3615 S/N Rotary Cutters P 27

28 Hitch Swivel Table of Contents Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

29 Section 2: Decks & Hitches Hitch Swivel Table of Contents Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A H H H H C C C C C C C C C C C C C C C C S Drawing Image Number SWIVEL HITCH * CLEVIS WELDMENT SHAFT WELDMENT SWIVEL RECEIVER CLEVIS SWIVEL GREASE ZERK 1/4-28 THD FORMING HHCS 5/8-11X1 3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 1-8X6 1/2 GR5 HHCS 1-8X5 1/2 GR5 NUT HEX JAM 1-8 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX SLOTTED 1 1/2-6 PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX 1-8 PLT WASHER FLAT 1 USS PLT WASHER FLAT 1 3/8HARD ASTMF436 PIN COTTER 1/4 X 2 1/2 PLT BUSHING CYL 1 1/4 X 1 X 1 BUSHING 1 1/4X1X5/8 ASSY SWIVEL CLEVIS Replaced By S S/N S/N S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 29

30 Table of Contents Leveling Rod & Wing Turnbuckle Applies to RC3615 S/N , RCM3615 S/N Section 2: Decks & Hitches RC(M)3615 S/N Rotary Cutters P 07/10/18

31 Table of Contents Leveling Rod & Wing Turnbuckle Section 2: Decks & Hitches Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg H H K C C C C C C C C C C C C C C Drawing Image Number WLDMT. LEVEL ROD SHORT LEVEL ROD LONG LEVEL ROD GREASE ZERK STRAIGHT 1/4-28 HHCS 1-8X4 1/2 GR5 HHCS 1-8X5 1/2 GR5 HSHCS 5/16-18X1 3/4 NUT HEX JAM 1 1/4-7 PLT NUT HEX JAM 7/8-9 NUT HEX NYLOCK 5/16-18 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX COUPLER 7/8-9 x 5 WASHER FLAT 3/4 SAE PLT WASHER LOCK 1 1/4 SPRING PLT PIN CLEVIS 3/4 X 1 1/2 PIN COTTER 1/8 X 1 1/4 PLT TRNBCKL, 1BORE W/SWIVEL /10/18 RC(M)3615 S/N Rotary Cutters P 31

32 Table of Contents Axle Center S/N Applies to RC3615 S/N , RCM3615 S/N Section 3: Axles RC(M)3615 S/N Rotary Cutters P 07/10/18

33 Table of Contents Axle Center S/N Section 3: Axles Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg D A H C C C C C C C C C C C C C C C C C C C C Drawing Image Number HUB GREASE CAP CENTER AXLE W/DUAL SPINDLES RPBY A GREASE ZERK 1/4-28 THD FORMING HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X9 GR5 HHCS 1-8X5 1/2 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 3/4-16 NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER HARDENED 3/4 PIN COTTER 5/32 X 1 3/4 LG SPINDLE-SINGLE BOLT-ON SPINDLE-DUAL BOLT-ON HUB 5-BOLT W/CUPS/STUDS HUB 5-BOLT COMPLETE SEAL 75ID CR17617 BRG CUP LM BRG CONE 25ID LM BRG CUP LM BRG CONE LM /10/18 RC(M)3615 S/N Rotary Cutters P 33

34 Table of Contents Axle Center S/N Applies to RC3615 S/N , RCM3615 S/N Section 3: Axles RC(M)3615 S/N Rotary Cutters P 07/10/18

35 Table of Contents Axle Center S/N Section 3: Axles Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg D K H C C C C C C C C C C C C C C C C C C C C C Drawing Image Number HUB GREASE CAP HUB 5 BOLT COMPLETE AXLE CENTER GREASE ZERK 1/4-28 THD FORMING HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X9 GR5 HHCS 1-8X5 1/2 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT CASTING HUB 5-BOLT W/CUPS/STUDS SPINDLE OFFSET, DUAL BOLT-ON SPINDLE, SINGLE BOLT ON 15 SPINDLE, SINGLE-BOLT ON 7/8-14 SEAL 75ID CR17617 BRG CUP LM BRG CONE 25ID LM BRG CUP LM BRG CONE LM Short Side Out W/29" Tire All Tires Except 29" AC 29" AC Tire Only 07/10/18 RC(M)3615 S/N Rotary Cutters P 35

36 Table of Contents Axle Wing S/N Applies to RC3615 S/N , RCM3615 S/N Section 3: Axles RC(M)3615 S/N Rotary Cutters P 07/10/18

37 Table of Contents Axle Wing S/N Section 3: Axles Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg D H H C C C C C C C C C C C C C C C C C C C C Drawing Image Number HUB GREASE CAP AXLE WING RH AXLE WING LH GREASE ZERK 1/4-28 THD FORMING HHCS 1-8X4 1/2 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X6 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 3/4-16 NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER HARDENED 3/4 PIN COTTER 5/32 X 1 3/4 LG SPINDLE-SINGLE BOLT-ON SPINDLE-DUAL BOLT-ON HUB 5-BOLT W/CUPS/STUDS HUB 5-BOLT COMPLETE SEAL 75ID CR17617 BRG CUP LM BRG CONE 25ID LM BRG CUP LM BRG CONE LM Shown 07/10/18 RC(M)3615 S/N Rotary Cutters P 37

38 Table of Contents Axle Wing S/N Applies to RC3615 S/N , RCM3615 S/N Section 3: Axles RC(M)3615 S/N Rotary Cutters P 07/10/18

39 Table of Contents Axle Wing S/N Section 3: Axles Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg D H H K C C C C C C C C C C C C C C C C C C C C Drawing Image Number HUB GREASE CAP AXLE WING RH AXLE WING LH HUB 5 BOLT COMPLETE GREASE ZERK 1/4-28 THD FORMING HHCS 1-8X4 1/2 GR5 HHCS 1/2-13X3 1/4 GR5 HHCS 1-8X6 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT CASTING HUB 5-BOLT W/CUPS/STUDS SPINDLE, SINGLE BOLT-ON 7/8-14 SPINDLE, DUAL BOLT-ON 7/8-14 SEAL 75ID CR17617 BRG CUP LM BRG CONE 25ID LM BRG CUP LM BRG CONE LM /10/18 RC(M)3615 S/N Rotary Cutters P 39

40 Table of Contents Guards Chain Double Row Front Applies to RC3615 S/N , RCM3615 S/N Section 4: Guards RC(M)3615 S/N Rotary Cutters P 07/10/18

41 Table of Contents Guards Chain Double Row Front Section 4: Guards Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A D D D D D K K D D K K C C C C Drawing Image Number CHNGRD FRONT DOUBLE * ROUND ROD 1/4 X 36 ROUND ROD 1/4 X 73 ROUND ROD 1/4 X 25 CHAINGUARD DBL FRONT CTR CHAINGUARD DBL FRONT WING ASSY. DUAL CHAINGUARD FRT.CTR ASSY.DUAL CHAINGUARD FRT.WING CHNGRD DBL FRT RH CHNGRD DBL FRT LH CHNGRD DBL FRT RH CHNGRD DBL FRT LH RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 5 LINK 07/10/18 RC(M)3615 S/N Rotary Cutters P 41

42 Table of Contents Guards Chain Double Row Rear Applies to RC3615 S/N , RCM3615 S/N Section 4: Guards RC(M)3615 S/N Rotary Cutters P 07/10/18

43 Table of Contents Guards Chain Double Row Rear Section 4: Guards Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A D D D D K K C C C C Drawing Image Number CHNGRD REAR DOUBLE * ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 9 CHNGRD REAR CNTR INNER DBL CHNGRD DBL REAR OUT CHNGRD CNTR REAR INNER DBL CHNGRD DBL REAR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 7-LINK 07/10/18 RC(M)3615 S/N Rotary Cutters P 43

44 Table of Contents Guards Chain Single Row Front Applies to RC3615 S/N , RCM3615 S/N Section 4: Guards RC(M)3615 S/N Rotary Cutters P 07/10/18

45 Table of Contents Guards Chain Single Row Front Section 4: Guards Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A K K D D D D D D D K K C C C C Drawing Image Number CHNGRD FRONT SINGLE * ASSY. CHAINGUARD FRT. CTR. ASSY. CHAINGUARD FRT. WING CHAINGUARD BRKT. FRT. CTR. ROUND ROD 1/4 X 36 CHAINGUARD BRKT. FRT. WING ROUND ROD 1/4 X 73 ROUND ROD 1/4 X 25 CHNGRD SGL FRT RH CHNGRD SGL FRT LH CHNGRD SGL FRT RH CHNGRD SGL FRT LH RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 5 LINK 07/10/18 RC(M)3615 S/N Rotary Cutters P 45

46 Table of Contents Guards Chain Single Row Rear Applies to RC3615 S/N , RCM3615 S/N Section 4: Guards RC(M)3615 S/N Rotary Cutters P 07/10/18

47 Table of Contents Guards Chain Single Row Rear Section 4: Guards Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A D D D D K K C C C C Drawing Image Number CHNGRD REAR SINGLE * ROUND ROD 1/4 X 31 1/2 ROUND ROD.25 X 9 BRACKET CHNGRD CNTR INNER CHNGRD SGL REAR OUT CHNGRD CNTR REAR INNER CHNGRD SGL REAR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT CHAIN 5/16 PROOF X 6 LINKS PLT CHAIN WELD 5/16 PROOF X 7-LINK 07/10/18 RC(M)3615 S/N Rotary Cutters P 47

48 Table of Contents Guards Rubber Front Applies to RC3615 S/N , RCM3615 S/N Section 4: Guards RC(M)3615 S/N Rotary Cutters P 07/10/18

49 Table of Contents Guards Rubber Front Section 4: Guards Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A D D D D D K K D K C C C C C Drawing Image Number RUBBERGUARD FRONT * DEFLECTOR BRKT. FRT. CTR. DEFLECTOR BRKT. FRT. WING DEFLECTOR STRAP DEFLECTOR STRAP DEFLECTOR STRAP ASSY. FRONT RUBBER CTR. ASSY. FRONT RUBBER WING RUBBERGUARD CNTR FRT RUBBERGUARD CTR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT RUBBER DEFLECTOR FRT. CTR. RUBBER DEF. FRT. CTR. OUT. RUBBER DEFLECTOR FRT. WING 07/10/18 RC(M)3615 S/N Rotary Cutters P 49

50 Table of Contents Guards Rubber Rear Applies to RC3615 S/N , RCM3615 S/N Section 4: Guards RC(M)3615 S/N Rotary Cutters P 07/10/18

51 Table of Contents Guards Rubber Rear Section 4: Guards Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg A D D D D K K C C C C Drawing Image Number RUBBER GUARD REAR * RUBBER GUARD FLAT BRKT. 28 1/2 BKT REAR CTR INNER RUBBER GRD BKT RBBRGRD CNTR OUT FLAT SUPPORT BAND ASY CTR REAR INNER RUBBER GRD RUBBERGUARD REAR CNTR OUT RHSNB 3/8-16X1 GR5 NUT HEX WHIZ 3/8-16 PLT RUBBER GUARD REAR CENTER RUBBER DEF REAR CNT OUT 07/10/18 RC(M)3615 S/N Rotary Cutters P 51

52 Table of Contents Driveline Center ( C) Comer Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

53 Table of Contents Driveline Center ( C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C Drawing Image Number PTO E60 X NM CLUTCH * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE COMER INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 Cat. 5 07/10/18 RC(M)3615 S/N Rotary Cutters P 53

54 Table of Contents Driveline Center ( C) Comer Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

55 Table of Contents Driveline Center ( C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. PTO E60 X NM CLUTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE CO INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 07/10/18 RC(M)3615 S/N Rotary Cutters P 55

56 Table of Contents Driveline Center 1000 RPM ( C) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

57 Table of Contents Driveline Center 1000 RPM ( C) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C D Drawing Image Number PTO INT. CAT W/CLUTCH EC YOKE ASSEMBLY (TRACT. END) EC CROSS ASSEMBLY EC OUTER TUBE YOKE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE EC CLUTCH FD2/6 1 3/4" Z20 RPBY EC.BOLT EC SPRING WASHER EC NUT EC BOLT ASSY KIT EC GREASE ZERK 8X1 45 DEG. Includes item 10 Includes items 7, 8 & 9 07/10/18 RC(M)3615 S/N Rotary Cutters P 57

58 Table of Contents Driveline Conv RPM ( C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

59 Table of Contents Driveline Conv RPM ( C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C C C Drawing Image Number PTO 2500 CAT /8-21 * WS YOKE 1 3/4-20 SPL.I.C WS YOKE 1 3/8-21 SPL. AS WS CROSS & BEARING KIT 2500 WS INBOARD YOKE 2500 WS SPRING PIN 10 X 90 WS INNER PROFILE S4 WS PROFILE & SLEEVE W.A. WS INBOARD YOKE 2400 DECAL DANGER GUARD MISS PTO WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS OUTER SHIELD TUBE OVAL DECAL DANGER PTO DRIVELINE WS INNER SHIELD TUBE RND. WS ASSY COLLAR KIT WS SHIELD CONE 7 RIB WS ZERK WS SUPPORT BEARING WS HEX BOLT M16 X 90 GR 8.8 WS LOCK NUT M16 SHIELD KIT, C WS REINFORCING COLLAR (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 59

60 Table of Contents Driveline CV RPM W/ Overrunning Clutch ( C) Weasler Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

61 Table of Contents Driveline CV RPM W/ Overrunning Clutch ( C) Weasler Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number DRVLN C CV ORCLTCH * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE OUTER GUARD WE GUARD REPAIR KIT WE SAFETY SIGN WE SAFETY SIGN WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE OVERRUNNING THRST CLTCH ASM 07/10/18 RC(M)3615 S/N Rotary Cutters P 61

62 Table of Contents Driveline CV 1000 RPM ( C) Weasler (S/N ) Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

63 Table of Contents Driveline CV 1000 RPM ( C) Weasler (S/N ) Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number RPBY C * WE SSL/AUTO-LOK REPAIR KIT WE AUTO-LOK YOKE ASY WE CAT 5 80 CROSS & BRG KIT WE CNTR HOUSING WE YOKE & SFT (69-20 SPL) WE GRD REPAIR KIT WE OUTER GRD WE INNER GRD WE GRD REPAIR KIT WE YOKE, TB & SLIP SLEEVE WE 44R CROSS & BRG KIT WE YOKE WE LOCK NUT WE BOLT X 00L GR8 WE JOINT & SFT HALF ASY W/GRD WE JOINT & TB HALF ASY W/GRD 1 3/8-21 Spline ---- (Obsolete) 07/10/18 RC(M)3615 S/N Rotary Cutters P 63

64 Table of Contents Driveline CV 1000 RPM ( C) Weasler Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

65 Table of Contents Driveline CV 1000 RPM ( C) Weasler Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number DRVLN C CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE GRD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT WE BOLT X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET WE CHAIN S/N S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 65

66 Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

67 Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg X C Drawing Image Number WS FRICTION CLUTCH * WS FLANGE YOKE WS FRICTION DISK WS HUB 1 3/4-20 I.C. WS THRUST PLATE WS BELLEVILLE SPRING WS HEX BOLT M10X50 NUT HEX NYLOCK M10X5 PLT COSMO WING NUT M8 WS HEX BOLT M12X65 07/10/18 RC(M)3615 S/N Rotary Cutters P 67

68 Table of Contents Driveline Slip Clutch 1000 RPM ( ) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

69 Table of Contents Driveline Slip Clutch 1000 RPM ( ) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg A Drawing Image Number EC CLUTCH FD2/6 1 3/4 20 SPL RPBY A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC HUB WITH FLANGE EC 7 DEGREE CONICAL DOG CONICAL DOG KIT EC INNER DISK EC PRESSURE DISK EC COMPLETE BOLT SV KIT, EC SLIP CLUTCH SPRING Contains 8 Springs Rev. 2 not compat. w/rev. Rev. 1 07/10/18 RC(M)3615 S/N Rotary Cutters P 69

70 Table of Contents Driveline Slip Clutch 1000 RPM ( ) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

71 Table of Contents Driveline Slip Clutch 1000 RPM ( ) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number EC CLUTCH FD2/6 1 3/4" Z20 * EC FD2-4/6 FLANGE WITH YOKE EC HUB WITH FLANGE NUT HEX M10X5 PLT EC BOLT (M10X85) EC SPRING EC PRESSURE DISK EC INNER DISK EC CLUTCH LINING RING CONICAL DOG KIT RPBY EC SELF LOCK SCREW NUT (M14) EC WASHER (D14) EC CLUTCH BUSHING 07/10/18 RC(M)3615 S/N Rotary Cutters P 71

72 Table of Contents Driveline Slip Clutch 540/1000 RPM ( ) EC Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

73 Table of Contents Driveline Slip Clutch 540/1000 RPM ( ) EC Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL * RPBY A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC PRESSURE DISK EC BOLT & SCREW NUT KIT REPL. SV KIT, EC SLIP CLUTCH SPRING Includes nut and washer Contains 8 Springs 07/10/18 RC(M)3615 S/N Rotary Cutters P 73

74 Table of Contents Driveline Wing ( C) Eurocardan Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

75 Table of Contents Driveline Wing ( C) Eurocardan Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C C C C Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD 1110MM EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD4/6 1 3/4 20 SPL EC CROSS ASSEMBLY EC INNER TUBE YOKE EC 1210MM INNER TUBE EC 10X70 ROLL PIN EC OUTER TUBE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSY 1 3/4-20(TRAC.END DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT(TRACT END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE EC BOLT EC SCREW NUT (M14) EC WASHER (d14) SHIELD KIT, C (S/N ) Includes 27,28 07/10/18 RC(M)3615 S/N Rotary Cutters P 75

76 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

77 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C X0 HM X Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20SPL I.C. WS CROSS & BRG KIT WS SPRING PIN 10 X 20 WS INBOARD YOKE 1B WS INNER PROFILE 1B 2400 WS PROFILE & SLEEVE W.A.1B/2AL WS INBOARD YOKE 2A WS FRICTION CLUTCH WS SHIELD CONE WS GUARD TUBE OUTER WS GUARD TUBE INNER WS BRG RING - SC25 DRIVELINE SHIELD SAFETY CHAIN WS SCREW WS SUPPORT BRG WS BOLT M12 X COSMO WING NUT M8 WS REINFORCING COLLAR (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 77

78 Table of Contents Driveline Wing ( C) Comer Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

79 Table of Contents Driveline Wing ( C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C Drawing Image Number RPBY C * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE OUTER COMER OUTER TUBE ROLL PIN COMER WIPER COMER TUBE OUTER COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER COMER SAFTEY CHAINS COMER TAPERED PIN SET 1 3/4 COMER TUBE W/YOKE/LUBE/FEMALE COMER TUBE W/YOKE/LUBE/MALE COMER HALF FEMALE GRD W/LABEL COMER HALF MALE GUARDING COMER CAP OUTER TUBE, PLASTIC (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 79

80 Table of Contents Driveline Wing ( C) Comer Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

81 Table of Contents Driveline Wing ( C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. DRVLN C FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET COMER CLUTCH, COMPLETE ASSY CO RETAINING COLLAR OUTER TUBE RPBY CO RETAINING COLLAR INNER TUBE CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARD COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER CO LABEL W/CUSTOMER CODE (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 81

82 Table of Contents Driveline Wing ( C) Comer Applies to RCM3615 S/N Section 5: Drivelines (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

83 Table of Contents Driveline Wing ( C) Comer Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE OUTER COMER OUTER TUBE ROLL PIN CO COMPLETE OUTER TUBE W/LABEL COMER INNER TUBE COMER ROLL PIN FOR INNER TUBE COMER INNER YOKE COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO U-JOINT FOR OUTER TUBE CO U-JOINT FOR INNER TUBE CO HALF FEMALE GUARD CO HALF MALE GUARD CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER COMER CAP OUTER TUBE, PLASTIC COMER INNER CAP CO LABEL W/CUSTOMER CODE (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 83

84 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

85 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20 SPL.I.C WS CROSS & BEARING KIT WS INBOARD YOKE S4 WS SPRING PIN 10 X 90 WS INNER PROFILE S4L WS OUTER PROFILE S5L WS INBOARD YOKE S5 WS FRICTION CLUTCH WS GUARD CONE 7 RIB WS BRG RING - SC25 WS GUARD TUBE OUTER RPBY WS GUARD TUBE INNER WS SCREW RPBY C RPBY C DRIVELINE SHIELD SAFETY CHAIN WS SUPPORT BEARING WS ZERK WS REINFORCING COLLAR WS GUARD CONE 6 RIB CC LOCK ASSY (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 85

86 Table of Contents Driveline Center ( C) Comer Applies to RC3615 S/N Section 5: Drivelines (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

87 Table of Contents Driveline Center ( C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg C Drawing Image Number PTO E60 X NM CLUTCH * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE COMER INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 Cat. 5 07/10/18 RC(M)3615 S/N Rotary Cutters P 87

88 Table of Contents Driveline Center ( C) Comer Applies to RC3615 S/N Section 5: Drivelines (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

89 Table of Contents Driveline Center ( C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. PTO E60 X NM CLUTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE, OUTER COMER SHAFT, SPLINED COMER ROLL PIN, INNER TUBE CO INNER YOKE COMER CLUTCH, COMPLETE ASSY COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 07/10/18 RC(M)3615 S/N Rotary Cutters P 89

90 Table of Contents Driveline Center 540 RPM ( C) Eurocardan Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

91 Table of Contents Driveline Center 540 RPM ( C) Eurocardan Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg C D Drawing Image Number PTO INT. CAT.4 540W/CLUTCH * EC BOLT ASSY KIT YOKE ASSEMBLY (TRACTOR END) CROSS ASSEMBLY OUTER TUBE YOKE 10 X 80-DIN-148 ROLL PIN EC TUBE JACK SHAFT RPBY D TORQUE LIMITER 4 FRICTION DISC EC.BOLT EC SPRING WASHER EC NUT WS ZERK M8 X 1 Includes items 7, 8 & 9 07/10/18 RC(M)3615 S/N Rotary Cutters P 91

92 Table of Contents Driveline Conv. 540 RPM ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

93 Table of Contents Driveline Conv. 540 RPM ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C C C Drawing Image Number PTO 2500 X NO CLUTCH * WS YOKE 1 3/4-20 SPL.I.C WS YOKE 1 3/8"-6 SPL. ASG WS CROSS & BEARING KIT 2500 WS INBOARD YOKE 2500 WS SPRING PIN 10 X 90 WS INNER PROFILE 2400 WS PROFILE & SLEEVE W.A. WS INBOARD YOKE 2400 DECAL DANGER GUARD MISS PTO WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS OUTER SHIELD TUBE RND. DECAL DANGER PTO DRIVELINE WS INNER SHIELD TUBE ROUND WS Q.D. PIN KIT WS SHIELD CONE 7 RIB WS ZERK WS SUPPORT BEARING WS HEX BOLT M16 X 90 GR 8.8 WS LOCK NUT M16 WS SHIELD CONE - 12 RIB SHIELD KIT, C WS REINFORCING COLLAR (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 93

94 Table of Contents Driveline CV 540 RPM ( C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

95 Table of Contents Driveline CV 540 RPM ( C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number RPBY C * WE SSL/AUTO-LOK REPAIR KIT WE AUTO-LOK YOKE ASY WE CAT 5 80 CROSS & BRG KIT WE CNTR HOUSING WE YOKE & SFT (69-20 SPL) WE GRD REPAIR KIT WE OUTER GRD WE INNER GRD WE GRD REPAIR KIT WE YOKE, TB & SLIP SLEEVE WE 44R CROSS & BRG KIT WE YOKE WE LOCK NUT WE BOLT X 00L GR8 WE JOINT & SFT HALF ASY W/GRD WE JOINT & TB HALF ASY W/GRD Obsolete 07/10/18 RC(M)3615 S/N Rotary Cutters P 95

96 Table of Contents Driveline CV 540 RPM ( C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

97 Table of Contents Driveline CV 540 RPM ( C) Weasler Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number DRVLN C CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT W/ CHAINS WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT WE BOLT X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET WE CHAIN (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 97

98 Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

99 Table of Contents Driveline Slip Clutch (229829X0) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg X C Drawing Image Number WS FRICTION CLUTCH * WS FLANGE YOKE WS FRICTION DISK WS HUB 1 3/4-20 I.C. WS THRUST PLATE WS BELLEVILLE SPRING WS HEX BOLT M10X50 NUT HEX NYLOCK M10X5 PLT COSMO WING NUT M8 WS HEX BOLT M12X65 07/10/18 RC(M)3615 S/N Rotary Cutters P 99

100 Table of Contents Driveline Slip Clutch 540/1000 RPM ( ) EC Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

101 Table of Contents Driveline Slip Clutch 540/1000 RPM ( ) EC Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL * RPBY A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC PRESSURE DISK EC BOLT & SCREW NUT KIT REPL. SV KIT, EC SLIP CLUTCH SPRING Includes nut and washer Contains 8 Springs 07/10/18 RC(M)3615 S/N Rotary Cutters P 101

102 Table of Contents Driveline Wing ( C) Eurocardan Applies to RC3615 S/N Section 5: Drivelines (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

103 Table of Contents Driveline Wing ( C) Eurocardan Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg C C C C Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD 1110MM EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD4/6 1 3/4 20 SPL EC CROSS ASSEMBLY EC INNER TUBE YOKE EC 1210MM INNER TUBE EC 10X70 ROLL PIN EC OUTER TUBE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSY 1 3/4-20(TRAC.END DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT(TRACT END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE EC BOLT EC SCREW NUT (M14) EC WASHER (d14) SHIELD KIT, C (S/N ) Includes 27,28 07/10/18 RC(M)3615 S/N Rotary Cutters P 103

104 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

105 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg C X0 HM X Drawing Image Number PTO CAT.4 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20SPL I.C. WS CROSS & BRG KIT WS SPRING PIN 10 X 20 WS INBOARD YOKE 1B WS INNER PROFILE 1B 2400 WS PROFILE & SLEEVE W.A.1B/2AL WS INBOARD YOKE 2A WS FRICTION CLUTCH WS SHIELD CONE WS GUARD TUBE OUTER WS GUARD TUBE INNER WS BRG RING - SC25 DRIVELINE SHIELD SAFETY CHAIN WS SCREW WS SUPPORT BRG WS BOLT M12 X COSMO WING NUT M8 WS REINFORCING COLLAR (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 105

106 Table of Contents Driveline Wing ( C) Comer Applies to RC3615 S/N Section 5: Drivelines (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

107 Table of Contents Driveline Wing ( C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg C Drawing Image Number RPBY C * COMER YOKE COMPLETE COMER CROSS ASSEMBLY COMER YOKE OUTER COMER OUTER TUBE ROLL PIN COMER WIPER COMER TUBE OUTER COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER COMER SAFTEY CHAINS COMER TAPERED PIN SET 1 3/4 COMER TUBE W/YOKE/LUBE/FEMALE COMER TUBE W/YOKE/LUBE/MALE COMER HALF FEMALE GRD W/LABEL COMER HALF MALE GUARDING COMER CAP OUTER TUBE, PLASTIC (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 107

108 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

109 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision dwg C Drawing Image Number RPBY C * WS YOKE 1 3/4-20 SPL.I.C WS CROSS & BRG KIT 2500 WS SPRING PIN 10 X 90 WS INBOARD YOKE S4 WS INNER PROFILE S4L WS OUTER PROFILE S5L WS INBOARD YOKE S5 WS FRICTION CLUTCH WS SHIELD CONE 7 RIB WS OUT SHIELD TUBE OVL WS INNER SHIELD TUBE RND WS BRG RING - SC25 DRIVELINE SHIELD SAFETY CHAIN WS SCREW WS SUPPORT BEARING WS SHIELD CONE - 6 RIB WS HEX BOLT M16 X 90 GR 8.8 WS LOCK NUT M16 WS REINFORCING COLLAR (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 109

110 Table of Contents Driveline Wing ( C) Comer Applies to RC3615 S/N Section 5: Drivelines (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

111 Table of Contents Driveline Wing ( C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. DRVLN C FX CLTCH COMER YOKE COMPLETE CO CROSS JOURNAL SET COMER CLUTCH, COMPLETE ASSY CO RETAINING COLLAR OUTER TUBE RPBY CO RETAINING COLLAR INNER TUBE CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARD COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER CO LABEL W/CUSTOMER CODE (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 111

112 Table of Contents Driveline Wing ( C) Comer Applies to RC3615 S/N Section 5: Drivelines (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

113 Table of Contents Driveline Wing ( C) Comer Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * COMER YOKE COMPLETE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE COMER YOKE OUTER COMER OUTER TUBE ROLL PIN CO COMPLETE OUTER TUBE W/LABEL COMER INNER TUBE COMER ROLL PIN FOR INNER TUBE COMER INNER YOKE COMER CLUTCH, DISC COMPLETE COMER RETAINING COLLER INNER COMER BOLT COMER RETAINING COLLER INNER CO SAFTEY CHAINS CO COMPLETE GUARD W/MANUAL COMER TAPERED PIN SET 1 3/4 COMER SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER CLUTCH SUPPORT COMER INNER PLATE COMER INTERMEDIATE PLATE COMER PRESSURE PLATE COMER BOLT WITH NUT M10X100 CO U-JOINT FOR OUTER TUBE CO U-JOINT FOR INNER TUBE CO HALF FEMALE GUARD CO HALF MALE GUARD CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHAFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER COMER CAP OUTER TUBE, PLASTIC COMER INNER CAP CO LABEL W/CUSTOMER CODE (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 113

114 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

115 Table of Contents Driveline Wing ( C) Walterscheid Section 5: Drivelines (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Image No. PTO CAT.5 W/CLUTCH 1 3/4-20 * WS YOKE 1 3/4-20 SPL.I.C WS CROSS & BEARING KIT WS INBOARD YOKE S4 WS SPRING PIN 10 X 90 WS INNER PROFILE S4L WS OUTER PROFILE S5L WS INBOARD YOKE S5 WS FRICTION CLUTCH WS GUARD CONE 7 RIB WS BRG RING - SC25 WS GUARD TUBE OUTER RPBY WS GUARD TUBE INNER WS SCREW RPBY C RPBY C DRIVELINE SHIELD SAFETY CHAIN WS SUPPORT BEARING WS ZERK WS REINFORCING COLLAR WS GUARD CONE 6 RIB CC LOCK ASSY (S/N ) 07/10/18 RC(M)3615 S/N Rotary Cutters P 115

116 Table of Contents Gearbox Center Deck (1000 RPM) ( C) Comer S/N Applies to RCM3615 S/N Section 6: Gearboxes (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

117 Table of Contents Gearbox Center Deck (1000 RPM) ( C) Comer S/N Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number GEARBOX COMER CO INPUT SHAFT CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING RTA25 CO BOLT M10X22 HHB CO PINION Z18 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X5 CO GEAR CROWN Z22 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY REP BY CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 67 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 117

118 Table of Contents Gearbox Divider 1000 RPM ( C) Comer Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

119 Table of Contents Gearbox Divider 1000 RPM ( C) Comer Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C C C Drawing Image Number DIVIDER OMNI/CO 1000RPM RD * CO BOLT M8X CO SPRING WASHER 8.4X13X2 CO COVER T1 BALL BEARING 6209 CO SNAP RING UNI 7437 CO OIL SEAL 45 X 85 X 10 CO CASING CO SHIM 79.9 BALL BEARING 6307 CO GEAR Z24 CO SNAP RING 40 UNI 7436 BALL BEARING 6208 CO SNAP RING 80 UNI 7437 CO SHAFT 1 3/4-20 CO OIL SEAL 45 X 80 X 10 CO SHAFT 1 3/4 Z20 CO SNAP RING SW 47 CO PINION Z20 CO SHIM 84.7 CO PLUG 3/8 GAS CO 1/2" GAS BREATHER PLUG * Notes: Oil Type 80-90W Capacity 5 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 119

120 Table of Contents Gearbox Divider 1000 RPM ( C) OMN Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

121 Table of Contents Gearbox Divider 1000 RPM ( C) OMN Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C Drawing Image Number GBOX DIV. OMNI RCD90 3:1RD OMNI SCREW, M8X35 OMNI LOCKWASHER, M8 SPLIT TYPE OMNI COVER OMNI BEARING BALL 6209 OMNI RETAINING RING, 85mm OMNI SEAL-INPUT OMNI HOUSING, RCD-90 OMNI SHIM-OUTPUT 0.1mm OMNI SHIM-OUTPUT 0.2mm OMNI SHIM-OUTPUT 0.5mm OMNI BEARING BALL 6307 OMNI PINION, 20T OMNI RETAINING RING 40mm OMNI BALL BEARING 208K OMNI RETAINING RING, 80mm OMNI SHFT OUTPUT SPLNE OMNI SEAL-OUTPUT OMNI SHAFT INPUT SPLNE OMNI RETAINING RING OMNI GEAR, 26T OMNI SHIM-INPUT 0.1mm OMNI SHIM-INPUT 0.2mm OMNI SHIM-INPUT 0.5mm OMNI PLG-PIPE, SCKT HD. 3/8-18 OMNI PLUG VENT 1/2-14 NPTF * Notes: Oil Type 80-90W Capacity 5 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 121

122 Table of Contents Gearbox Divider 1000 RPM ( C) SD Engineering Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

123 Table of Contents Gearbox Divider 1000 RPM ( C) SD Engineering Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision dwg C C Drawing Image Number DIV. OMNI/CO 1000RPM RD * SD HOUSING ITG RETAINING RING SD 40DIA SHAFT RETAINING RING BRG BALL 6208 SD RETAINING RING SD OUTPUT SHAFT SD OIL SEAL 45X80X10 SD RETAINING RING 85 SD THRU SHAFT SD OIL SEAL 45X85X10 SD BALL BEARING 209 SD 20 TOOTH GEAR SD M8 HELICAL SPRING LOCK WSHR SD 24 TOOTH GEAR SD 3/8-18 NPT SQ HEAD PLUG SD 3/8-19NPT SQ HEAD PLUG SD BALL BEARING 307 SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD INSPECTION CAP COVER ITG M18 X 5P PLUG VENTED SD M8X25X40 HEX HEAD CAPP SW ITG SEALING WASHER S/N S/N S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 123

124 Table of Contents Gearbox Left Deck 1000 RPM ( C) Comer (S/N ) Applies to RCM3615 S/N Section 6: Gearboxes (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

125 Table of Contents Gearbox Left Deck 1000 RPM ( C) Comer (S/N ) Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number GEARBOX COMER CO INPUT SHAFT CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING RTA25 CO BOLT M10X22 HHB CO GEAR CROWN Z22 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X5 CO PINION Z18 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY REP BY CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 67 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 125

126 Table of Contents Gearbox Right Deck 1000 RPM ( C) Comer (S/N ) Applies to RCM3615 S/N Section 6: Gearboxes (1000 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

127 Table of Contents Gearbox Right Deck 1000 RPM ( C) Comer (S/N ) Section 6: Gearboxes (1000 RPM) Applies to RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C A Drawing Image Number GEARBOX COMER CO INPUT SHAFT CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING RTA25 CO BOLT M10X22 HHB CO GEAR CROWN Z22 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M40X5 CO PINION Z18 M6 COMER SHIM KIT RPBY A (SHIM KIT) IGT BEARING ASSEMBLY RPBY BY CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 40.3 X 67 X 1 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 127

128 Table of Contents Gearbox Center & Left Deck (540 RPM ) ( C) Comer S/N Applies to RC3615 S/N Section 6: Gearboxes (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

129 Table of Contents Gearbox Center & Left Deck (540 RPM ) ( C) Comer S/N Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number GEARBOX COMER CO COVER CO BOLT M10X22 HHB CO SNAP RING 50 UNI7435 CO INPUT SHAFT CO CAP CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING RTA25 CO SHIM 45.3X5 CO PLUG 3/8 GAS CO CASTING & MACHINE CO NUT M30 X 5 CO COTTER PIN B 5X60 CO PINION Z16 M6 CO SHIM 50.3X70.3 ITG BEARING ASSEMBLY CO OUTPUT SHAFT CO SEAL (50x90x10) CO SEAL RETAINER CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO COTTER PIN B6 X 60 CO OIL SEAL 45 X 85 X 10 CO GEAR CROWN Z23 M6 CO 3/8 GAS OIL VENT LEVEL PG. CO OIL PLUG 3/8 * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 129

130 Table of Contents Gearbox Divider 540 RPM ( C) Comer Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

131 Table of Contents Gearbox Divider 540 RPM ( C) Comer Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C C C Drawing Image Number DIVIDER OMNI/CO 540RPM SU * CO BOLT M8X CO SPRING WASHER 8.4X13X2 CO COVER T1 BALL BEARING 6209 CO SNAP RING UNI 7437 CO OIL SEAL 45 X 85 X 10 CO CASING CO SHIM 79.9 BALL BEARING 6307 CO PINION Z20 CO SNAP RING 40 UNI 7436 BALL BEARING 6208 CO SNAP RING 80 UNI 7437 CO SHAFT 1 3/4-20 CO OIL SEAL 45 X 80 X 10 CO SHAFT 1 3/4 Z20 CO SNAP RING SW 47 CO GEAR Z24 CO SHIM 84.7 CO PLUG 3/8 GAS CO 1/2" GAS BREATHER PLUG * Notes: Oil Type 80-90W Capacity 5 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 131

132 Table of Contents Gearbox Divider 540 RPM ( C) SD Engineering Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

133 Table of Contents Gearbox Divider 540 RPM ( C) SD Engineering Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C Drawing Image Number DIV. OMNI/CO 540RPM SU * SD HOUSING ITG RETAINING RING SD 40DIA SHAFT RETAINING RING BRG BALL 6208 SD RETAINING RING SD OUTPUT SHAFT SD OIL SEAL 45X80X10 SD RETAINING RING 85 SD THRU SHAFT SD OIL SEAL 45X85X10 SD BALL BEARING 209 SD 24 TOOTH GEAR SD M8 HELICAL SPRING LOCK WSHR SD 20 TOOTH GEAR SD 3/8-18 NPT SQ HEAD PLUG SD 3/8-19NPT SQ HEAD PLUG SD BALL BEARING 307 SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD SHIM (0.20) SD SHIM (0.30) SD SHIM (0.50) SD INSPECTION CAP COVER ITG M18 X 5P PLUG VENTED SD M8X25X40 HEX HEAD CAPP SW ITG SEALING WASHER S/N S/N S/N S/N /10/18 RC(M)3615 S/N Rotary Cutters P 133

134 Table of Contents Gearbox Right Deck 540 RPM ( C) Comer (S/N ) Applies to RC3615 S/N Section 6: Gearboxes (540 RPM) RC(M)3615 S/N Rotary Cutters P 07/10/18

135 Table of Contents Gearbox Right Deck 540 RPM ( C) Comer (S/N ) Section 6: Gearboxes (540 RPM) Applies to RC3615 S/N Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number GEARBOX COMER CO INPUT SHAFT CO OIL SEAL 45 X 85 X 10 CO SNAP RING UNI 7437 CO SHIM 84.7 CO BEARING RTA25 CO BOLT M10X22 HHB CO GEAR CROWN Z23 M6 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS CO COTTER PIN B 5X60 CO NUT M30 X 5 CO PINION Z16 M6 CO SHIM 50.3X70.3 REP BY CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO COTTER PIN B6 X 60 CO 3/8 GAS OIL VENT LEVEL PG. * Notes: Oil Type 80-90W Capacity 6 Pints 07/10/18 RC(M)3615 S/N Rotary Cutters P 135

136 Table of Contents Hydraulic Cylinder ( C) Cross Applies to RC3615 S/N , RCM3615 S/N Section 7: Hydraulics RC(M)3615 S/N Rotary Cutters P 07/10/18

137 Table of Contents Hydraulic Cylinder ( C) Cross Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C 1D A A D A D A D A D D D A C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * BASE CROSS CROSS NUT, CLEVIS & TIE ROD MW O-RING TIE ROD CROSS TUBE CROSS CROSS SCREW, CAP CROSS CLEVIS PIN CROSS PIN, CLIP CROSS ROD CLEVIS CROSS NUT, CLEVIS & TIE ROD ROD CROSS MW WIPER BACK-UP O-RING HEAD CROSS MW BACKUP CROSS PISTON CROSS NUT, PISTON SEAL KIT CROSS 5 CYL 1C4982 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 07/10/18 RC(M)3615 S/N Rotary Cutters P 137

138 Table of Contents Hydraulic Cylinder ( C) Midway Applies to RC3615 S/N , RCM3615 S/N Section 7: Hydraulics RC(M)3615 S/N Rotary Cutters P 07/10/18

139 Table of Contents Hydraulic Cylinder ( C) Midway Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C 6M3118 2A0012 7M3320 5M3120 2A0006 2A0208 2A0132 1M6010 2A0012 2M3418 3R0406 4M3108 4M3102 2A C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * MW BASE MW NUT CLEVIS & TIE ROD MW O-RING MW TIE MW TUBE MW CAPSCREW MW CLEVIS PIN MW PIN CLIP MW CLEVIS STD. DUTY MW NUT CLEVIS & TIE ROD MW ROD MW WIPER BACK-UP O-RING MW HEAD MW BACKUP MW PISTON RPBY 4M3108 MW NUT, PISTON SEAL KIT MW 5X25ROD 3A3104 Only found in seal kit 19 ROD Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 Only found in seal kit 19 07/10/18 RC(M)3615 S/N Rotary Cutters P 139

140 Table of Contents Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

141 Table of Contents Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C C N/A N/A N/A N/A N/A N/A C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * NUT HEX 3/8-16 PLT MON PISTON NUT LION PIN MON CLEVIS PIN COTTER SCREW SET SH 3/8-16X3/8 TYPE C PLUG 9/16-18UNF MORB SOCKET HD MON ROD SEAL MON PISTON SEAL MON END CAP BACKUP WASHERS MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING LION CYL TUBE 5 X 12 LION TIE ROD 3/8, 12 CYL LION ROD 25 X 12 LION ROD CLEVIS 1 1/8-12UNF LION CLEVIS CAP 5, 9/16 ORB MON ROD CAP5-25-3/4ORB-TSS MON PISTON TSS-ISO-WR MON SEAL KIT Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 07/10/18 RC(M)3615 S/N Rotary Cutters P 141

142 Table of Contents Hydraulic Cylinder ( C) Midway Applies to RC3615 S/N , RCM3615 S/N Section 7: Hydraulics RC(M)3615 S/N Rotary Cutters P 07/10/18

143 Table of Contents Hydraulic Cylinder ( C) Midway Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C 6R1164-ADI 6M4166 2A0014 7M4316 5M4116 2A0006 1M6010-ADI 2A0012 2M4416 3M4412 4M4104 2A C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * MIDWAY ADI BASE RPBY 6R1164-ADI MW TIE ROD NUT O-RING MW TIE ROD 3 X 8 CYLINDER MW TUBE 3 X 8 CYLINDER MW CAPSCREW MIDWAY HARDENED CLEVIS ADI MW NUT CLEVIS & TIE ROD MW ROD 1-1/4 DIA X 8 STROKE WIPER BACK-UP O-RING MW HEAD CAP 3X1-1/4 ROD 3/4SAE BACK-UP MW PISTON 3 DIA. MW PISTON NUT 1-14 CYL SEAL KIT 3 X 7 MW 3A4104 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 Only found in sealkit 17 07/10/18 RC(M)3615 S/N Rotary Cutters P 143

144 Table of Contents Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18

145 Table of Contents Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg C C C N/A N/A N/A N/A N/A N/A C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * NUT HEX 1/2-13 PLT MON PISTON NUT SCREW SET SH 3/8-16X3/8 TYPE C LION PLUG 3/4-16UNF SOCKET HD MON ROD SEAL MON PISTON SEAL (PSP) MON END CAP B/U WASHER MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING MON TIE ROD EXTND THD MON PISTON TSS-ISO-WR MON CYL TUBE MON TIE ROD MON ROD CP /16ORB-TS MON CLEVIS CAP MON CYL ROD LION HARDENED ROD CLEVIS 1 1/4 MON SEAL KIT Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 07/10/18 RC(M)3615 S/N Rotary Cutters P 145

146 Table of Contents Hydraulic Lift Components Applies to RC3615 S/N , RCM3615 S/N Section 7: Hydraulics RC(M)3615 S/N Rotary Cutters P 07/10/18

147 Table of Contents Hydraulic Lift Components Section 7: Hydraulics Applies to RC3615 S/N , RCM3615 S/N Ref. Part No. Part Description Comments Revision Dwg H D C C C C C C C C C C C C C C C C C C C C C Image No. WLDMT. CYLINDER PIN TRANSPORT BAR FILL PLUG VENTED 3/4-16 PLT HHCS 3/8-16X1 GR5 HHCS M8X25X55 GR8.8 NUT FLANGE LOCK 3/8-16 PLT WASHER FLAT 3/8 USS PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 1 SAE PIN, HAIR COTTER 3/16 WIRE DIA PIN COTTER 3/16 X 1 1/2 PLT SPRING HOSE LOOP CYL 5X12X25 ROD (TIE ROD) CYL 3X8X25 ROD (TIE) NO PINS STRK CNTRL SPCRS 125 TO 50 OREL 1/32 9/16MJIC 9/16MORB EL 3/4MJIC 3/4MORB HH1/4R /16FJIC TE 9/16MJIC BH 9/16MJIC 9/16MJ CP 3/4FORB MALE QD POPPET TYPE HH3/8R /4MORB 3/4FJIC HH3/8R /4MORB 9/16FJIC MON PIN KIT 00C/W COTTER PIN Includes 2 clevis pins & 4 cotter pins 07/10/18 RC(M)3615 S/N Rotary Cutters P 147

148 Decal Placement Table of Contents Section 8: Decals Applies to RC3615 S/N , RCM3615 S/N RC(M)3615 S/N Rotary Cutters P 07/10/18