Rotary Cutter RC(M)3712 & RCG(M) P Parts Manual. Copyright 2018 Printed 09/10/18

Transcription

1 Rotary Cutter RC(M)3712 & RCG(M) P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2018 Printed 09/10/18 Cover photo may show optional equipment not supplied with standard unit.

2 Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Decks & Hitches...6 Blade Carrier...6 Deck Center Components...8 Deck Center Drive Components...10 Deck Wing Components...12 Deck Wing Drive Components...14 Hitch A-Frame...16 Hitch Ball Coupler...18 Hitch Bar Tite...20 Hitch Fixed Clevis...22 Hitch LP Performance...24 Hitch Pintle...26 Leveling Rods & Wing Turnbuckles...28 Light Assembly...30 Manual Tube...32 Section 3: Axles...34 Axle Center...34 Axle Wing...36 Spindle & Hub Assembly ( S)...38 Tire Options...40 Section 4: Guards...42 Guards Chain Double Row Front...42 Guards Chain Double Row Rear...44 Guards Chain Single Row Front...46 Guards Chain Single Row Rear...48 Section 5: Drivelines...50 Driveline ( C) Comer...50 Driveline ( C) Comer...52 Driveline CV RPM ( C) Weasler...54 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler...56 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler...58 Driveline CV 540 RPM ( C) Weasler...60 Section 6: Gearboxes...62 Gearbox ( C) Comer...62 Gearbox ( C) Comer...64 Gearbox ( C) Comer...66 Gearbox ( C) Comer...68 Gearbox ( C) Comer...70 Gearbox ( C) Comer...72 Section 7: Hydraulics...74 Hydraulic Cylinder ( C) Red Lion...74 Hydraulic Cylinder ( C) Red Lion...76 Hydraulic Lift Components...78 Section 8: Decals...80 Decals...80 Touch-up Paints...82 Section 9: Options & Accessories...84 Single Duplex Accessory Copyright All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

3 Alphabetized Table of Contents A B D G H L M S Axle Center...34 Axle Wing...36 Blade Carrier...6 Decals...80 Deck Center Components...8 Deck Center Drive Components...10 Deck Wing Components...12 Deck Wing Drive Components...14 Driveline ( C) Comer...50 Driveline ( C) Comer...52 Driveline CV RPM ( C) Weasler...54 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler...56 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler...58 Driveline CV 540 RPM ( C) Weasler...60 Gearbox ( C) Comer...62 Gearbox ( C) Comer...64 Gearbox ( C) Comer...66 Gearbox ( C) Comer...68 Gearbox ( C) Comer...70 Gearbox ( C) Comer...72 Guards Chain Double Row Front...42 Guards Chain Double Row Rear...44 Guards Chain Single Row Front...46 Guards Chain Single Row Rear...48 Hitch A-Frame...16 Hitch Ball Coupler...18 Hitch Bar Tite...20 Hitch Fixed Clevis...22 Hitch LP Performance...24 Hitch Pintle...26 Hydraulic Cylinder ( C) Red Lion...74 Hydraulic Cylinder ( C) Red Lion...76 Hydraulic Lift Components...78 Touch-up Paints...82 Leveling Rods & Wing Turnbuckles...28 Light Assembly...30 Manual Tube...32 Single Duplex Accessory...84 Spindle & Hub Assembly ( S)...38 T Tire Options /10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 3

4 4 RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

5 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 5

6 Blade Carrier Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

7 Section 2: Decks & Hitches Blade Carrier Table of Contents Ref. Part No. Part Description Comments Revision Dwg H C C C C C C A Image No. 15 DISHPAN WLDMT LG.HUB(COMER) BLD BLT 1 1/8-12X44 W/.25KEY NUT HEX TOP LOCK 1 1/8-12 PLT WASHER FLAT 1" HARDENED CUTTER BLADE 1/2X4X25 CCW CUTTER BLADE 1/2X4X19 CCW CUTTER BLADE 1/2X4X19 CW BLADE BOLT KIT Center deck (standard) Right deck (standard) Left deck (standard) 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 7

8 Deck Center Components Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

9 Deck Center Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg S H H H H H H H C C C C C C C C Image No. MANUAL STORAGE CONTAINER KIT CENTER DECK CENTER DECK GREEN CENTER DECK ORANGE CENTER DECK RED CENTER DECK YELLOW CENTER DECK, GAL CENTER SKID SHOE GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X4 GR5 HHCS 1/2-13X1 1/2 GR5 NUT HEX WHIZ 1/2-13 PLT GR5 NUT HEX FLANGE LOCK 5/8-11 PLT WASHER FLAT 1/2 USS PLT SPRING HOSE LOOP HEAVY PLUG LP 3" ID RUBBER Beige deck Green deck Orange deck Red deck Yellow deck Galvanized deck (RCG cutters) 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 9

10 Deck Center Drive Components Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

11 Deck Center Drive Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg D D H H C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C Image No. SHIELD MOUNT BRACKET SPLITTER BOX SHIELD INTERMEDIATE SHIELD SHIELD BRACKET, SPLITTER HHCS 5/16-18X3/4 GR5 HHCS 3/4-10X2 1/4 GR5 HFS 1/4-20X5/8 GR5 HHCS M8X25X45 GR8.8 HHCS 3/8-16X8 GR5 ZNYCR NUT HEX FLG TP LK 5/16-18ZNYCR NUT FLANGE LOCK 3/8-16 PLT NUT HEX NYLOCK 1/4-20 NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 5/16 SAE PLT COMER U DIPSTICK COMER VENT # DRVLN C CV DRVLN C CV ORCL DRVLN C CV DRVLN C CV ORCLTCH DRVLN C4 6F FL CLTCH GBOX RC :83 STD GBOX RC :1 STD DIV 540RPM 1:35 DIV 1000RPM 35:1 DRVLN SHLD CONE, 2 PIECE LONG HHCS M8X25X20 GR8.8 THD-LCK MAGNET, 3 3/16 OD X 57LB FLUSH MOUNT LEVER LATCH HHCS M5X.80X30 GR8.8 NUT HEX M5X RPM 540 RPM 1000 RPM 1000 RPM 540 & 1000 RPM cutter 540 RPM 1000 RPM 540 RPM 1000 RPM 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 11

12 Deck Wing Components Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

13 Deck Wing Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg D H H H H H H H H H H H H H H H K C C C C C C C C C Image No. RH REAR DEFLECTOR RH DECK RH DECK GREEN RH DECK ORANGE RH DECK RED RH DECK YELLOW LH DECK LH DECK GREEN LH DECK ORANGE LH DECK RED LH DECK YELLOW RH DECK, GAL LH DECK, GAL BEVELED SKID SHOE RH BEVELED SKID SHOE LH HINGE ROD HINGE ROD ASY GREASE ZERK STRAIGHT 1/4-28 HHCS 3/8-16X1 1/2 GR5 RHSNB 1/2-13X1 1/4 GR5 PLOW 3/8-16X1 1/4 GR5 NUT HEX 3/8-16 PLT NUT HEX WHIZ 1/2-13 PLT GR5 NUT HEX WHIZ 3/8-16 PLT WASHER LOCK SPRING 3/8 PLT PLUG LP 3" ID RUBBER Right beige wing Right green wing Right orange wing Right red wing Right yellow wing Left beige wing Left green wing Left orange wing Left red wing Left yellow wing Right galvanized wing (RCG cutters) Left galvanized wing (RCG cutters) 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 13

14 Deck Wing Drive Components Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

15 Deck Wing Drive Components Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg C C C C C C C C C C Image No. HHCS 3/4-10X2 1/4 GR5 NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 5/16 PLT WASHER FLAT 5/16 USS PLT COMER U DIPSTICK GBOX RC :69 REV GBOX RC :69 STD DRVLN C FX CLTCH DRIVELINE SHIELD CONE, 2 PIECE HHCS M8X25X20 GR8.8 THD-LCK Right wing 540 & 1000 RPM Left Wing 540 & 1000 RPM Right & left wing. 540 & 1000 RPM 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 15

16 Hitch A-Frame Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

17 Section 2: Decks & Hitches Hitch A-Frame Table of Contents Ref. Part No. Part Description Comments Revision Dwg H D D D H C C C C C C C C C C C C C C C C C C C C C C Image No. ADJUSTABLE JACK MOUNT PTO HANGER HINGE PTO HANGER PIVOT PIN 1" SHORT TONGUE RHSNB 3/8-16X1 GR5 HHCS 1/2-13X1 1/2 GR5 HHCS 1-8X2 1/2 GR5 RHSNB 1/2-13X1 1/2 GR5 SHLDR BLT 1/2DX1/2L 3/8-16 SS NUT HEX 3/8-16 PLT NUT HEX 1/2-13 PLT NUT HEX 3/4-10 PLT NYLOCK NUT HEX 1-8 PLT NUT HEX WHIZ 1/2-13 PLT GR5 NUT HEX TOP LOCK 1-8 PLT NUT FLANGE LOCK 3/8-16 PLT WASHER FLAT 3/8 USS PLT WASHER LOCK SPRING 3/8 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 USS PLT WASHER FLAT 3/4 SAE PLT WASHER LOCK SPRING 1 PLT WASHER FLAT 1 USS PLT PIN SPIRAL 3/8X1 1/2 HVY DUTY SPRING HOSE LOOP HEAVY SAFETY CHAIN LB 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 17

18 Hitch Ball Coupler Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

19 Hitch Ball Coupler Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg A H C C Drawing Image Number BALL HITCH, 2 5/16 * 2 5/16" BALL HITCH WELDMENT HHCS 5/8-11X1 3/4 GR5 NUT HEX WHIZ 5/8-11 PLT For 2-5/16" Ball 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 19

20 Hitch Bar Tite Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

21 Section 2: Decks & Hitches Hitch Bar Tite Table of Contents Ref. Part No. Part Description Comments Revision Dwg A D D H H H H C C C C C C C C C C C C C C C Image No. BAR TITE HITCH * HITCH WEAR PLATE WIDE FORMED HITCH SUPPORT WIDE BAR TITE WIDE TOP SWIVEL RECEIVER PIVOT SHAFT BAR TITE PIVOT WELDMENT GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 FTHD HHCS 3/4-10X6 GR5 HHCS 1-8X5 1/2 GR5 HHCS 1-8X7 GR8 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX FLANGE LOCK 3/4-10 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX SLOTTED 1 3/4-5 REGULR WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER HARD 75X75X.25 PLT PIN COTTER 1/4 X 3 PLT BUSHING 50ODX00IDX25 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 21

22 Hitch Fixed Clevis Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

23 Hitch Fixed Clevis Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg A H D H C C C C C C Image No. FIXED CLEVIS HITCH * CLEVIS WELDMENT HITCH SPACER CLEVIS RECIEVER YOKE HHCS 5/8-11X1 3/4 GR5 FTHD HHCS 5/8-11X9 GR5 NUT LOCK 5/8-11 PLT NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT HHCS 1-8X9 1/2 GR8 SPTHD 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 23

24 Hitch LP Performance Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

25 Hitch LP Performance Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg A D H H H C C C C C C C C C C C C Image No. LAND PRIDE PERFORMANCE HITCH * HITCH HOLDER HITCH CLEVIS SWIVEL RECEIVER LPH YOKE GREASE ZERK STRAIGHT 1/4-28 HHCS 5/8-11X1 3/4 GR5 FTHD HHCS 3/8-16X1 1/4 GR5 NUT HEX COUPLER 3/8-16X1 3/4 NUT HEX FLG LOCK 1-8 GR B PLT NUT HEX WHIZ 5/8-11 PLT NUT HEX SLOTTED 1 3/4-5 REGULR WASHER LOCK SPRING 3/8 PLT WASHER HARD 75X75X.25 PLT PIN COTTER 1/4 X 3 PLT HHCS 1-8X7 GR8 SPTHD BUSHING 1 1/4X1X5/8 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 25

26 Hitch Pintle Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

27 Section 2: Decks & Hitches Hitch Pintle Table of Contents Ref. Part No. Part Description Comments Revision 5. Dwg A H C C C C Image No. FIXED PINTLE HITCH * PINTLE RECEIVER HHCS 5/8-11X1 3/4 GR5 FTHD HFS 5/8-11X2 1/2 GR8 PLT NUT HEX WHIZ 5/8-11 PLT PINTLE HOOK SQ.BASE BDB /10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 27

28 Leveling Rods & Wing Turnbuckles Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

29 Leveling Rods & Wing Turnbuckles Section 2: Decks & Hitches Ref. Part No. Part Description Comments Revision Dwg K H H K C C C C C C C C C C C C C C Image No. TURNBUCKLE KIT LEVEL ROD SHORT 1" LEVEL ROD LEVEL ROD ASY GREASE ZERK STRAIGHT 1/4-28 HSHCS 5/16-18X1 3/4 HHCS 1-8X5 GR8 PLT SPTHD NUT HEX 3/4-10 PLT NYLOCK NUT HEX JAM 1-8 PLT NUT HEX JAM 1 1/4-7 PLT NUT HEX NYLOCK 5/16-18 PLT NUT HEX LOCK 1-8 PLT NUT HEX COUPLER 1-8 X 5 WASHER FLAT 3/4 SAE PLT WASHER LOCK 1 1/4 SPRING PLT PIN CLVS.75X50 USBL HT PIN COTTER 1/8 X 1 1/4 PLT HHCS 3/4-10X4 GR8 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 29

30 Light Assembly Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

31 Section 2: Decks & Hitches Light Assembly Table of Contents Ref. Part No. Part Description Comments Revision Dwg D D D C C C C C C C C C C C C C Image No. LIGHT BRACKET RH LIGHT BRACKET LH LIGHT GUARD CABLE TIE.19X D 50LB RHSNB 3/8-16X1 GR5 RHSNB 1/2-13X1 1/4 GR5 HHCS 1/4-20X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT GR5 NUT FLANGE LOCK 3/8-16 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT DUAL LED LIGHT LH DUAL LED LIGHT RH ENHANCE MODULE LEAD WIRE HARNESS 13' LIGHT WIRE HARNESS 2' 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 31

32 Manual Tube Table of Contents Section 2: Decks & Hitches RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

33 Section 2: Decks & Hitches Manual Tube Table of Contents Ref. Part No. Part Description Comments Revision Dwg S C C C C Image No. MANUAL STORAGE CONTAINER KIT * HHCS 1/4-20X1 GR5 NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT MANUAL STORAGE CONTAINER 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 33

34 Axle Center Table of Contents Section 3: Axles RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

35 Section 3: Axles Axle Center Table of Contents Ref. Part No. Part Description Comments Revision Dwg H S H H D C C C C C C C C C C C Image No. CENTER AXLE SHORT SPINDLE AND HUB ASY PIVOT PIN 5" USEABLE CENTER SPRING ROCKER PIVOT PIN 1" LONG HHCS 1/2-13X1 3/4 GR5 FTHD NUT HEX 3/4-10 PLT NYLOCK NUT HEX FLG LOCK 1/2-13 PLT NUT HEX LOCK 1-8 PLT WASHER FLAT 1/2 SAE PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 SAE PIN SPIRAL 3/8X1 1/2 HVY DUTY SPRING COMP 20OD.63W 5.5L SLEEVE BEARING 1 I.D. SLEEVE BEARING 25ID X 25 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 35

36 Axle Wing Table of Contents Section 3: Axles RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

37 Section 3: Axles Axle Wing Table of Contents Ref. Part No. Part Description Comments Revision Dwg H H S D C C C C Image No. RH WING AXLE LH WING AXLE SHORT SPINDLE AND HUB ASY PIVOT PIN 1" SHORT NUT HEX 3/4-10 PLT NYLOCK WASHER FLAT 3/4 SAE PLT PIN SPIRAL 3/8X1 1/2 HVY DUTY SLEEVE BEARING 1 I.D. Right axle Left axle 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 37

38 Spindle & Hub Assembly ( S) Section 3: Axles RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

39 Spindle & Hub Assembly ( S) Section 3: Axles Ref. Part No. Part Description Comments Revision Dwg S D V C C C C C C C C C C C C C C C C Image No. SHORT SPINDLE AND HUB ASY * HUB GREASE CAP HUB 5 BOLT COMPLETE GREASE ZERK 1/4-28 THD FORMING HHCS 1/2-13X3 1/4 GR5 HUB STUD 1/2-20X88 GR5 NUT LOCK 1/2-13 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX 1/2-20 X 5/8 HIGH WASHER SPINDLE - 7/8 PIN COTTER 5/32 X 1 3/4 LG HUB 5-BOLT W/CUPS/STUDS SINGLE AXLE SPINDLE, SHORT HD PURGEABLE SEAL 75X71 BRG CUP LM BRG CONE 25ID LM BRG CUP LM BRG CONE LM HUB 5-BOLT CASTING 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 39

40 Tire Options Table of Contents Section 3: Axles RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

41 Section 3: Axles Tire Options Table of Contents Ref. Part No. Part Description Comments Revision Dwg C C C C Drawing Image Number TIRE & WHL LAM. 6X9X21(5-BOLT) NEW TIRE FF 25.5X PLY NEW TIRE 25.5X PLY TIRE & WHL LAM 6X26 (5-BOLT) 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 41

42 Guards Chain Double Row Front Section 4: Guards RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

43 Guards Chain Double Row Front Section 4: Guards Ref. Part No. Part Description Comments Revision Dwg A D D D D D D K K K C C C Image No. DOUBLE CHAIN GUARDS * ROUND ROD 1/4 X 19 ROUND ROD 1/4 X 34 ROUND ROD 1/4 X 58 CHAIN GUARD, FNT CTR FRONT WING CHAIN GUARD CHAIN GUARD, FRNT CTR OUTSIDE CHAIN GUARD, DBL FNT CTR CHAIN GUARD, DBL FNT WING CHAIN GUARD, DBL FNT CTR OUTER RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT GR5 CHAIN WELD 5/16 GR 43 X 9-LINK Includes complete front and rear double chain guard assemblies 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 43

44 Guards Chain Double Row Rear Section 4: Guards RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

45 Guards Chain Double Row Rear Section 4: Guards Ref. Part No. Part Description Comments Revision Dwg A D D D D D D K K K C C C Image No. DOUBLE CHAIN GUARDS * ROUND ROD 1/4 X 30 1/2 ROUND ROD 1/4 X 34 ROUND ROD.25 X 9 CHAIN GUARD, REAR CTR OUTER CHAIN GUARD, REAR CNTR CHAIN GUARD, REAR WING CHAIN GUARD, DBL REAR CTR OUT CHAIN GUARD, DBL REAR CTR CHAIN GUARD, DBL REAR WING RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT GR5 CHAIN WELD 5/16 GR 43X11-LINK Includes complete front and rear double chain guard assemblies 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 45

46 Guards Chain Single Row Front Section 4: Guards RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

47 Guards Chain Single Row Front Section 4: Guards Ref. Part No. Part Description Comments Revision Dwg A D D D D D D K K K C C C Image No. SINGLE CHAIN GUARDS * ROUND ROD 1/4 X 19 ROUND ROD 1/4 X 34 ROUND ROD 1/4 X 58 CHAIN GUARD, FNT CTR FRONT WING CHAIN GUARD CHAIN GUARD, FRNT CTR OUTSIDE CHAIN GUARD, SGL FNT CTR CHAIN GUARD, SGL FNT WING CHAIN GUARD, SGL FNT CTR OUTER RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT GR5 CHAIN WELD 5/16 GR 43 X 5 LINK Includes complete front and rear single chain guard assemblies 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 47

48 Guards Chain Single Row Rear Section 4: Guards RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

49 Guards Chain Single Row Rear Section 4: Guards Ref. Part No. Part Description Comments Revision Dwg A D D D D D D K K K C C C C Image No. SINGLE CHAIN GUARDS * ROUND ROD 1/4 X 30 1/2 ROUND ROD 1/4 X 34 ROUND ROD.25 X 9 CHAIN GUARD, REAR CTR OUTER CHAIN GUARD, REAR CNTR CHAIN GUARD, REAR WING CHAIN GUARD, SGL REAR CTR OUT CHAIN GUARD, SGL REAR CTR CHAIN GUARD, SGL REAR WING RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT GR5 CHAIN 5/16 GR 43 X 6 LINKS PLT CHAIN 5/16 GR 43 X 6 LINKS PLT Includes complete front and rear single chain guard assemblies 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 49

50 Driveline ( C) Comer Section 5: Drivelines RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

51 Driveline ( C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision Dwg Image No. CO YOKE WITH GREASE NIPPLE CO CROSS JOURNAL SET CO CIRCLIP CO GREASE NIPPLE CO BOLT & NUT M23X90 CO FLANGED YOKE MALE CO RETAINING WASHER CO FLANGED YOKE FEMALE CO COMPLETE DISC CLTCH F29 CO YOKE COMER GREASE FITTING CO SPRING COMER YOKE, FLANGED COMER BUSH RPBY COMER TAPERED PIN SET 1 3/4 CO CLUTCH SUPPORT F29 COMER INNER PLATE COMER PRESSURE PLATE CO BOLT M10X85 & NUT 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 51

52 Driveline ( C) Comer Section 5: Drivelines RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

53 Driveline ( C) Comer Section 5: Drivelines Ref. Part No. Part Description Comments Revision Dwg Image No. COMER YOKE COMPLETE CO CROSS JOURNAL SET CO COMPLETE DISC CLTCH F29 OB RPBY RPBY RPBY CO COMPLETE GUARD W/ INSTR MNL COMER TAPERED PIN SET 1 3/4 CO SPRING COMER YOKE, FLANGED COMER BUSH COMER LINING RING CO CLUTCH SUPPORT F29 COMER INNER PLATE COMER PRESSURE PLATE CO BOLT M10X85 & NUT CO HALF FEMALE SHFT W/GUARDING CO HALF MALE SHFT W/GUARDING COMER DANGER LABEL OUTER TUBE COMER DANGER LABEL GUARD OUTER 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 53

54 Driveline CV RPM ( C) Weasler Section 5: Drivelines Applies to RCGM3712, RCM RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

55 Driveline CV RPM ( C) Weasler Section 5: Drivelines Applies to RCGM3712, RCM3712 Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number DRVLN C CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT WE BOLT X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 55

56 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler Applies to RCGM3712, RCM3712 Section 5: Drivelines RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

57 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler Section 5: Drivelines Applies to RCGM3712, RCM3712 Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number DRVLN C CV ORCLTCH * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE OUTER GUARD WE GUARD REPAIR KIT WE SAFETY SIGN WE SAFETY SIGN WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE OVERRUNNING THRST CLTCH ASM 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 57

58 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler Applies to RC3712, RCG3712 Section 5: Drivelines RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

59 Driveline CV RPM W/ Overrunning Clutch ( C) Weasler Section 5: Drivelines Applies to RC3712, RCG3712 Ref. Part No. Part Description Comments Revision Dwg C Image No. DRVLN C CV ORCL * WE GUARD SET WE JOINT & TUBE HALF GUARD SET WE JOINT & SHFT HALF GUARD SET WE JOINT & SHAFT HALF GUARDED RPBY WE JOINT & TUBE HALF ASM W/GRD WE JOINT & TUBE HALF ASM WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE OUTER GUARD WE GRD REPAIR KIT WE SAFETY SIGN WE DECAL LAND PRIDE WE SAFETY SIGN WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE OVERRUNNING THRST CLTCH ASM 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 59

60 Driveline CV 540 RPM ( C) Weasler Section 5: Drivelines Applies to RC3712, RCG RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

61 Driveline CV 540 RPM ( C) Weasler Section 5: Drivelines Applies to RC3712, RCG3712 Ref. Part No. Part Description Comments Revision Dwg C Drawing Image Number DRVLN C CV * WE SSL/AUTO-LOK REPAIR KIT WE WWCV AUTO-LOK YOKE ASM WE AB8/AW25EBL CROSS KIT WE WWCV CENTER HOUSING WE YOKE&SHAFT (69-20 SPLINE) WE GUARD REPAIR KIT W/ CHAINS WE OUTER GUARD WE INNER GUARD WE YOKE, TUBE & SLIP SLEEVE WE 55EBL CROSS KIT WE YOKE WE LOCK NUT WE BOLT X 00L GR8 WE JOINT&SHFT HALF ASM W/GUARD WE JOINT&TUBE HALF ASM W/GUARD WE GUARD SET WE CHAIN (S/N ) 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 61

62 Gearbox ( C) Comer Section 6: Gearboxes RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

63 Gearbox ( C) Comer Section 6: Gearboxes Ref. Part No. Part Description Comments Revision Dwg C A A C Drawing Image Number GBOX RC :69 STD * CO INPUT SHAFT CO DUST LIP (45X85X10) CO SNAP RING UNI 7437 COMER SHIM KIT CO BRG TAPPERED CO BOLT M10X22 HHB CO GEAR CROWN Z27 M5.3 CO SNAP RING 50 UNI7435 CO OIL PLUG 3/8 CO COVER CO SHIM 45.3X5 CO CAP CO PLUG 3/8 GAS (SOLID PLUG) CO COTTER PIN B 5X60 CO NUT M30 X 5 CO PINION Z16 M5.3 COMER SHIM KIT ITG BRG ASSEMBLY CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO SHIM 44X30.3X1 CO SPACER (30.1X45X6) CO COTTER PIN B6 X 60 COMER U DIPSTICK 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 63

64 Gearbox ( C) Comer Applies to RCGM3712, RCM3712 Section 6: Gearboxes RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

65 Gearbox ( C) Comer Section 6: Gearboxes Applies to RCGM3712, RCM3712 Ref. Part No. Part Description Comments Revision Dwg C A A C Image No. GBOX RC :1 STD * CO INPUT SHAFT COMER OIL SEAL 45X85X10 COMER SNAP RING INT D85 UNI7437 COMER SHIM KIT 70.3X87 COMER BEARING TAPERED COMER HHB M10X22 GR8.8 CO CROWN Z17 M7.5 COMER SNAP RING EXT D50 UNI7435 CO OIL PLUG 3/8 CO COVER COMER SHIM 65.3X45.3X5 COMER CAP 85X10 CO PLUG 3/8 GAS (SOLID PLUG) CO COTTER PIN B 5X60 CO NUT M40X5 COMER SHIM KIT 50.3X70.3 BRG CUP/CONE SET CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO NAME PLATE COMER SHIM 40.3X67X1 CO COTTER PIN B6 X 60 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 65

66 Gearbox ( C) Comer Section 6: Gearboxes RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

67 Gearbox ( C) Comer Section 6: Gearboxes Ref. Part No. Part Description Comments Revision Dwg C A A C Image No. GBOX RC :69 REV * CO INPUT SHAFT COMER OIL SEAL 45X85X10 COMER SNAP RING INT D85 UNI7437 COMER SHIM KIT 70.3X87 COMER BEARING TAPERED COMER HHB M10X22 GR8.8 CO GEAR CROWN Z27 M5.3 COMER SNAP RING EXT D50 UNI7435 CO PLUG EXTERNAL 3/8 GAS CO COVER COMER SHIM 65.3X45.3X5 COMER CAP 85X10 CO PLUG 3/8 GAS (SOLID PLUG) CO COTTER PIN B 5X60 CO NUT M30 X 5 CO PINION Z16 M5.3 COMER SHIM KIT 50.3X70.3 BRG CUP/CONE SET CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO BLANK WASHER CO NUT, CASTLE M30 X 2 CO NAME PLATE CO SHIM 44X30.3X1 COMER SPACER CO COTTER PIN B6 X 60 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 67

68 Gearbox ( C) Comer Applies to RCGM3712, RCM3712 Section 6: Gearboxes RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

69 Gearbox ( C) Comer Section 6: Gearboxes Applies to RCGM3712, RCM3712 Ref. Part No. Part Description Comments Revision Dwg C A C C A C A C Image No. DIV 1000RPM 35:1 * CO CASING CO BEVEL GEAR FORGED M.75 Z27 CO BEVEL GEAR FORGED M.75 Z20 COMER SHIM KIT BRG BALL 6209 CO DUST LIP (45X85X10) CO SHAFT 1 3/4 Z20 COMER SNAP RING INT D85 UNI7437 BRG BALL 37IDX14ODX CO SNAP RING 80 UNI 7437 CO OIL SEAL 45 X 80 X 10 CO SHAFT 1 3/4-20 COMER SHIM KIT Z18 M6.15 CO PLUG 3/8 GAS (SOLID PLUG) COMER COVER CO BOLT M8X CO SNAP RING SW 47 CO UNDER CAP 1/2 GAS BRG BALL 6208 CO SHIM 79.7 RTA35 CO SNAP RING 40 UNI 7436 CO NAME PLATE CO IDENTIFICATION LABEL COMER VENT # /10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 69

70 Gearbox ( C) Comer Applies to RC3712, RCG3712 Section 6: Gearboxes RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

71 Gearbox ( C) Comer Section 6: Gearboxes Applies to RC3712, RCG3712 Ref. Part No. Part Description Comments Revision Dwg C A A C Image No. GBOX RC :83 STD * CO INPUT SHAFT COMER OIL SEAL 45X85X10 COMER SNAP RING INT D85 UNI7437 COMER SHIM KIT 70.3X87 COMER BEARING TAPERED COMER HHB M10X22 GR8.8 CO CROWN WHEEL Z22 M6.5 COMER SNAP RING EXT D50 UNI7435 CO PLUG EXTERNAL 3/8 GAS COMER SHIM 65.3X45.3X5 CO PLUG 3/8 GAS (SOLID PLUG) CO COTTER PIN B 5X60 CO NUT M30 X 5 CO PINION Z12 M75 COMER SHIM KIT 50.3X70.3 BRG CUP/CONE SET CO CASTING & MACHINE CO SEAL (50x90x10) CO SEAL RETAINER CO OUTPUT SHAFT CO NUT, CASTLE M30 X 2 CO NAME PLATE CO SHIM 40X30.3X5 CO COTTER PIN B6 X 60 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 71

72 Gearbox ( C) Comer Applies to RC3712, RCG3712 Section 6: Gearboxes RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

73 Gearbox ( C) Comer Section 6: Gearboxes Applies to RC3712, RCG3712 Ref. Part No. Part Description Comments Revision Dwg C A C C A C A C Image No. DIV 540RPM 1:35 * CO CASING CO PINION Z20 M75 CO CROWN WHEEL Z27 M75 COMER SHIM KIT 70.3X87 BRG BALL 6209 COMER OIL SEAL 45X85X10 CO SHAFT 1 3/4 Z20 COMER SNAP RING INT D85 UNI7437 BRG BALL 37IDX14ODX CO SNAP RING 80 UNI 7437 CO OIL SEAL 45 X 80 X 10 CO SHAFT 1 3/4-20 COMER SHIM KIT Z18 M6.15 CO PLUG 3/8 GAS (SOLID PLUG) COMER COVER CO BOLT M8X CO SNAP RING SW 47 CO UNDER CAP 1/2 GAS BRG BALL 6208 CO SHIM 79.7 RTA35 CO SNAP RING 40 UNI 7436 CO NAME PLATE COMER VENT # /10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 73

74 Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

75 Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics Ref. Part No. Part Description Comments Revision Dwg C C C N/A N/A N/A N/A N/A N/A C Drawing Image Number CYL 5X12X25 ROD (TIE ROD) * NUT HEX 3/8-16 PLT MON PISTON NUT LION PIN MON CLEVIS PIN COTTER SCREW SET SH 3/8-16X3/8 TYPE C PLUG 9/16-18UNF MORB SOCKET HD MON ROD SEAL MON PISTON SEAL MON END CAP BACKUP WASHERS MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING LION CYL TUBE 5 X 12 LION TIE ROD 3/8, 12 CYL LION ROD 25 X 12 LION ROD CLEVIS 1 1/8-12UNF LION CLEVIS CAP 5, 9/16 ORB MON ROD CAP5-25-3/4ORB-TSS MON PISTON TSS-ISO-WR MON SEAL KIT Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 Only Found in Kit #20 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 75

76 Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

77 Hydraulic Cylinder ( C) Red Lion Section 7: Hydraulics Ref. Part No. Part Description Comments Revision Dwg C C C N/A N/A N/A N/A N/A N/A C Drawing Image Number CYL 3X8X25 ROD (TIE) NO PINS * NUT HEX 1/2-13 PLT MON PISTON NUT SCREW SET SH 3/8-16X3/8 TYPE C LION PLUG 3/4-16UNF SOCKET HD MON ROD SEAL MON PISTON SEAL (PSP) MON END CAP B/U WASHER MON END CAP O-RING SEAL WIPER ROD MON PISTON WEAR RING MON TIE ROD EXTND THD MON PISTON TSS-ISO-WR MON CYL TUBE MON TIE ROD MON ROD CP /16ORB-TS MON CLEVIS CAP MON CYL ROD LION HARDENED ROD CLEVIS 1 1/4 MON SEAL KIT Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 Only found in seal kit #19 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 77

78 Hydraulic Lift Components Section 7: Hydraulics RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

79 Hydraulic Lift Components Section 7: Hydraulics Ref. Part No. Part Description Comments Revision Dwg D C C C C C C C C C C C C C C C C C C C Image No. HOSE WRAP, 1FT VENT PLUG - 9/16-18 PLATED FILL PLUG VENTED 3/4-16 PLT WASHER FLAT 1 SAE PIN COTTER 3/16 X 1 1/2 PLT PIN CLVS 0X20 USBL CYL 5X12X25 ROD (TIE ROD) CYL 3X8X25 ROD (TIE) NO PINS STRK CNTRL SPCRS 125 TO 50 AD 3/4MORB 3/4MJIC HH1/4R /16FJIC HH1/4R /16FJIC TE 9/16MJIC OREL 1/16 9/16MJIC 9/16MORB CP 3/4FORB MALE QD POPPET TYPE HH3/8R /4MORB 3/4FJIC HH3/8R /4MORB 9/16FJIC HG HANDLE - BLACK EXT HG HANDLE - RED RET AD 3/4MORB 3/4FORB (HG) 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 79

80 Decals Table of Contents Section 8: Decals RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

81 Section 8: Decals Decals Table of Contents Ref. Part No. Part Description Comments Revision Dwg C C C C C C C C C C C C C C C C C C C C C C C C C C Image No. DECAL CAUTION 540 RPM DECAL CAUTION 1000 RPM DECAL DANGER PTO DRIVELINE EN DECAL FLAG DECAL AMBER REFLECTOR DECAL RED REFLECTOR DECAL DANGER PTO DRIVELINE DECAL 5 YEAR GEARBOX WARRANTY DECAL REFLECTOR RED 2X9 DECAL REFLECTOR AMBER 2X9 DECAL LANDPRIDE 34" TAN/BROWN DECAL JACK ADJUSTMENT DECAL, RC3712 DECAL, RCM3712 DECAL, RCG3712 DECAL, RCGM3712 DECAL CW BLADE ROTATION DECAL CCW BLADE ROTATION DECAL DANGER ROTATE BLADE DECAL, 7-SERIES DECAL CUTTER SAFETY COMBO DECAL, CUTTER PINCH POINT DECAL, CYLINDER LOCKS DECAL, SAFETY COMBO, TONGUE DECAL, GUARD MISSING DECAL, LANDPRIDE.COM 540 RPM 1000 RPM RC3712 RCM3712 RCG3712 RCGM3712 Under wing decks 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 81

82 Touch-up Paints Section 8: Decals No diagram associated with this Parts List 82 RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

83 Touch-up Paints Section 8: Decals Ref. Part No. Part Description Comments Revision C C C C C C C CTU CTU CTU CTU CTU CTU CTU CQT CQT CQT CQT CQT CQT CQT CGL CGL CGL CGL CGL CGL CGL LP BEIGE SPRAY CAN GLOSS BLACK SPRAY CAN MED. RED SPRAY TRCK/CTR GREEN SPRAY CUTTERS ORANGE SPRAY CAN BLUE SPRAY CAN PAINT ALUMINUM/ZINC SPRAY CAN LP BEIGE TOUCH-UP 5OZ GLOSS BLACK TOUCH-UP 5OZ MED RED TOUCH-UP 5OZ GREEN TOUCH-UP 5OZ ORANGE TOUCH-UP 5OZ BLUE TOUCH-UP 5OZ PAINT ALUMINUM/ZINC TOUCH UP LP BEIGE QUART GLOSS BLACK QUART MED RED QUART GREEN QUART ORANGE QUART BLUE QUART PAINT ALUMINUM/ZINC QUART LP BEIGE GALLON GLOSS BLACK GALLON MED RED GALLON GREEN GALLON ORANGE GALLON BLUE GALLON PAINT ALUMINUM/ZINC GALLON Spray can Spray can Spray can Spray can Spray can Spray can Spray can Touch-up bottle with brush Touch-up bottle with brush Touch-up bottle with brush Touch-up bottle with brush Touch-up bottle with brush Touch-up bottle with brush Touch-up bottle with brush Quart can Quart can Quart can Quart can Quart can Quart can Quart can Gallon can Gallon can Gallon can Gallon can Gallon can Gallon can Gallon can 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 83

84 Single Duplex Accessory Section 9: Options & Accessories RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

85 Single Duplex Accessory Section 9: Options & Accessories Ref. Part No. Part Description Comments Revision Dwg A C C C Image No. SINGLE DUPLEX FITTINGS BUNDLE CR 9/16MJIC AD 9/16FJIC 3/4MORB AD 3/4MJIC 9/16FJIC 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 85

86 The is a numeric index of all part numbers included in this manual. The index shows what page(s) the part is used on. Part Number Page Part Number Page Part Number Page Part Number Page , , 65, , 67, , 65, 67, , 65, , 67, 69, 71, , 65, 67, , 65, , 65, 67, , 67, , , , 65, 67, , , , , , 57, 59, , 57, 59, , , , , , , , , , , , , , , , 57, D , , 57, 59, , 57, 59, H D...45, D...43, D...43, 45, 47, A D...45, S...9, K D...43, H H D D H D D...43, D...45, D D D H H H H H H H H H H H H H H H H H S...35, 37, D D H D...43, D...43, D...45, D...45, D D H H K K K K H H H D D...17, D D D H H H H K H K K K K K K K K K A...47, A...43, A A A H A A H...21, H H H H H H V H H H H A , , , , , 65, 67, , , 65, 67, , 65, 67, , 65, 67, , 65, 67, , 65, 67, , , , 65, 67, 69, 71, , , , , , 65, 67, 69, 71, , 65, 67, , 65, 67, 69, 71, , C...9, 13, 21, 25, C C C C C...75, C C C...17, C C...19, 21, 23, 25, C C...11, C C C C...9, C C C C C C C... 13, 31, 43, 45, 47, C C C C C C C C C C C C C...13, 17, C C...17, C C...17, 29, 35, C C C C C... 9, 13, 17, 31, 43, 45, 47, C C...17, C C C C C C C...11, 17, C...11, 31, C...21, 23, C C...11, C...19, 21, 23, 25, C C...29, C...21, C C C...31, C...11, RC(M)3712 & RCG(M)3712 Rotary Cutter P 09/10/18

87 (continued) Part Number Page Part Number Page Part Number Page Part Number Page C...11, CTU C C C CGL C...11, 13, 17, CQT C CTU C C C...9, CGL C...17, 21, 29, 35, CQT C CTU C...17, C C...35, CGL C CQT C CTU C C C CGL C...21, CQT C CTU C C C CGL C...21, CQT C CTU C C C...17, 35, CGL C...9, CQT C CTU C...75, C C...77, C C C C C C C...69, C C...69, C C...69, C C...65, 67, C C...11, 15, C C...11, 69, C C...11, C C...11, C C...15, C C...11, C C...11, C C...15, C...11, C C C C C...11, C C...11, C C...11, C C C C C C C C C C...35, C C C...9, C C C C C C...11, C C C C C C C C C C C C C C C C C C C C CGL C CQT C C C C C C C C C C C C C C C C C C C C C , , , , , , 57, 59, 61 A , 73 A , 65, 67, 69, 71, 73 A , 65, 67, 71 A , 73 Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg Dwg N/A...75, 77 09/10/18 RC(M)3712 & RCG(M)3712 Rotary Cutter P 87