INTERSTATER PARTS MANUAL. ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas Flail

Transcription

1 INTERSTATER Flail Rev PARTS MANUAL Part No P ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or Alamo Industrial ( ) to obtain a Free copy before operating the equipment Alamo Group, Inc.

2

3 BOLT TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loctite, and torqued to the dry values listed in the torque chart based on the bolt size and hardness. Other structures such as pump mounting bolts should be installed with Blue Loctite and torqued to the dry values indicated in the chart. Bolt tightness should be completed with and checked with a suitable torque wrench. Torque checks should be completed throughout the life of the mower in accordance with the maintenance chart provided in this manual. Loose bolts on a frame or in a casting may be a result of: Vibration from the mower due to imbalance of the mower blades Pulled threads due to over tightening Distortion of the hole due to under tightening during installation Bolts broken or sheared in the mounting structure or tractor may be the result of: Improper alignment of the Mounting Plate or Structure such that it is not sitting flat on the mating surface Distortion of the bolt due to over-tightening Under tightening of the bolts Check the bolt torque during installation and prior to delivery with a suitable torque wrench.

4 TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.

5 CHANGE PAGES Date of Change Page Number (EXAMPLE ONLY: ECN##### - chg pages 17, 23, 137) document release date chg pages - 35, chg pgs 94, 101, chg pgs chg pgs 90 Change Pages - 5

6 CHANGE PAGES The following is a listing of pages that have been changed since the latest publication date for the overall document. Change Pages - 6

7 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. Note: Please refer to The Safety Section in the front of this Manual for the proper part number when ordering replacement safety decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Industrial Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas Alamo Group Inc. Parts Section 2

8 PART NAME INDEX CHECK CHAINS - REAR MOWER... 5 CLUTCH ASY - P/N CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 AND BELOW)... 8 CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 TO CURRENT) CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 AND BELOW) CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 TO CURRENT) CONTROL VALVE ASY - W/ STAND CUTTER KNIVES - CC - FC - RENV - PACKAGES & KITS CUTTER KNIVES - CC - FC - RENV - SINGLE & BULK CYLINDER ASY - LIFT CYL - P/N A CYLINDER ASY - TILT CYL - P/N A CYLINDER ATTACHMENT - LIFT & TILT DRIVELINE ASY - P/N GEARBOX ASY - P/N HYD SCHEMATIC - CYL HOSE - CONTROL DUAL WING HYD SCHEMATIC W/ PARTS - DUAL WING HYD SCHEMATIC W/ PARTS - RIGHT WING FIRST HYD SCHEMATIC W/ PARTS - RIGHT WING ONLY HYD TANK ASY - PN MOTOR ASY - LEFT WING MOTOR ASY - RIGHT WING MOTOR REPAIR PARTS - P/N MOTOR REPAIR PARTS - P/N MOWER ASY - LH & RH WING 50 (PART 1) MOWER ASY - LH & RH WING 50 (PART 2) MOWER ASY - LH & RH WING 50 (PART 3) MOWER ASY - LH & RH WING 62 (PART 1) MOWER ASY - LH & RH WING 62 (PART 2) MOWER ASY - LH & RH WING 62 (PART 3) MOWER ASY - LH & RH WING 74 (PART 1) MOWER ASY - LH & RH WING 74 (PART 2) MOWER ASY - LH & RH WING 74 (PART 3) MOWER ASY - LH & RH WING 88 (PART 1) MOWER ASY - LH & RH WING 88 (PART 2) MOWER ASY - LH & RH WING 88 (PART 3) MOWER ASY - REAR 88 (PART 1) MOWER ASY - REAR 88 (PART 2) MOWER ASY - REAR 88 (PART 3) MOWER ASY - REAR 88 (PART 4) MOWER ASY - REAR 96 (PART 1) Alamo Group Inc. Parts Section -3

9 PART NAME INDEX MOWER ASY - REAR 96 (PART 2) MOWER ASY - REAR 96 (PART 3) MOWER ASY - REAR 96 (PART 4) OPTIONAL CASTER WHEELS - REAR MOWER LAMINATED OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 1) OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 2) OPTIONAL EQUIPMENT - ACCESSORIES - PACKAGES PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 1) PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 2) PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 1) PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 2) PUMP ASY - SINGLE PUMP - SINGLE WING PUMP ASSY,TANDEM FRONT PUMP 2.77CID PUMP ASY - TANDEM FRONT PUMP - DUAL WINGS PUMP ASY - TANDEM REAR PUMP - DUAL WINGS PUMP ASY, GEAR TYPE - FRONT - HYD CYL SUPPLY PN TUBING ASY HYD - DUAL WING ASY P/N TUBING ASY HYD - SINGLE WING - ASY P/N VALVE REMOTE CONTROL WIRE HARNESS - DUAL WINGS WIRE HARNESS - RH WING - FIRST OR ONLY Alamo Group Inc. Parts Section -4

10 CHECK CHAINS - REAR MOWER CHECK CHAIN KIT ASY CHAIN - 9 LINKS BOLT NUT WASHER LIFT CHAIN CLEVIS - UPPER LIFT CHAIN CLEVIS - LOWER 2014 Alamo Group Inc. Parts Section -5

11 CLUTCH ASY - P/N CLUTCH ASY, 4-DISK YOKE, FLANGED BODY, FRICTION CLUTCH PRESSURE PLATE RING,CLUTCH LINING BUSHING SPRING CLUTCH NUT & BOLT 14MM X 70MM BOLT & NUT M10 X 95 MM SELF LK NUT INNER PLATE 2014 Alamo Group Inc. Parts Section -6

12 THIS PAGE INTENTIONALLY LEFT BLANK 2014 Alamo Group Inc. Parts Section -7

13 CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 AND BELOW) 2014 Alamo Group Inc. Parts Section -8

14 CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 AND BELOW) Continued VALVE ASY, 2-SPOOL COMPLETE HANDLE KIT ASY CHECK VALVE KIT ASY SPOOL POSITION KIT (TILT SECTION) DUST COVER (TILT SECTION) TILT SECTION, COMPLETE (INC. 1-3) BODY SEAL KIT SPOOL POSITION KIT (LIFT SECTION) DUST COVER (LIFT SECTION) LIFT SECTION, COMPLETE (INC. 1,2,7) OUTLET SECTION RELIEF VALVE KIT INLET SECTION SEAL KIT INLET SECTION, W/RELIEF VALVE # MOUNTING BRACKET TIE ROD KIT (2 SECTION VALVE) SWIVEL HOSE ADAPTER W/ O-RING SWIVEL UNION, 1/4 MALE X 1/4 FEMALE 90` STRAIGHT ADAPTER KNOB BRACKET STRAIGHT ADAPTER STRAIGHT ADAPTER ORIFICE PLATE 2014 Alamo Group Inc. Parts Section -9

15 CONTROL VALVE ASY - 2 SPOOL (SEPT 2010 TO CURRENT) VALVE 2-SPOOL W/BRKTS KIT, HANDLE ASSY KIT, CHECK VALVE ASSY KIT SPOOL POSITION DUST COVER (TILT SECTION) SECTION TILT COMPLETE KIT, BODY SEAL SECTION, OUTLET KIT, RELIEF VALVE KIT, INLET SECTION SEAL SECTION, INLET W/RELIEF VALVE BRACKET MOUNTING KIT TIE ROD KNOB, CONTROL VALVE BRACKET, CONTROL BRACKET, CONTROL SPOOL WIPER O-RING, SPOOL SEAL BUSHING, SPOOL SEAL ADP HYD STGHT 6MB-4MJ ORIFICE, ONE-WAY RSTCR ADP HYD STGHT 6MB-4MJ 2014 Alamo Group Inc. Parts Section -10

16 THIS PAGE INTENTIONALLY LEFT BLANK 2014 Alamo Group Inc. Parts Section -11

17 CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 AND BELOW) 2014 Alamo Group Inc. Parts Section -12

18 CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 AND BELOW) Continued VALVE ASY, 4-SPOOL COMPLETE HANDLE KIT ASY CHECK VALVE KIT ASY SPOOL POSITION KIT (TILT SECTION) DUST COVER (TILT SECTION) TILT SECTION, COMPLETE (INC. 1-3) BODY SEAL KIT SPOOL POSITION KIT (LIFT SECTION) DUST COVER (LIFT SECTION) LIFT SECTION, COMPLETE (INC. 1,2,7) OUTLET SECTION RELIEF VALVE KIT INLET SECTION SEAL KIT INLET SECTION, W/RELIEF VALVE # MOUNTING BRACKET TIE ROD KIT (4 SECTION VALVE) SWIVEL HOSE ADAPTER W/ O-RING SWIVEL UNION, 1/4 MALE X 1/4 FEMALE 90` STRAIGHT ADAPTER KNOB BRACKET STRAIGHT ADAPTER STRAIGHT ADAPTER ORIFICE PLATE 2014 Alamo Group Inc. Parts Section -13

19 CONTROL VALVE ASY - 4 SPOOL (SEPT 2010 TO CURRENT) VALVE 4-SPOOL W/BRKTS KIT,HANDLE ASSY KIT,CHECK VALVE ASSY KIT SPOOL POSITION DUST COVER (TILT SECTION) SECTION TILT COMPLETE KIT, BODY SEAL SECTION, OUTLET KIT, RELIEF VALVE KIT, INLET SECTION SEAL SECTION, INLET W/RELIEF VALVE BRACKET MOUNTING KIT TIE ROD KNOB,CONTROL VALVE BRACKET,CONTROL VALVE BRACKET,CONTROL VALVE SPOOL WIPER O-RING, SPOOL SEAL BUSHING, SPOOL SEAL ADP HYD STGHT 6MB-4MJ ORIFICE, ONE-WAY RSTCR ADP HYD STGHT 6MB-4MJ 2014 Alamo Group Inc. Parts Section -14

20 THIS PAGE INTENTIONALLY LEFT BLANK 2014 Alamo Group Inc. Parts Section -15

21 CONTROL VALVE ASY - W/ STAND 2014 Alamo Group Inc. Parts Section -16

22 CONTROL VALVE ASY - W/ STAND Continued VALVE MOUNTING BRACKET COVER TOP VALVE ASY, 4-SPOOL (W/ FITTINGS VALVE ASY, 4-SPOOL (W/O FITTINGS) VALVE ASY, 2-SPOOL (W/ FITTINGS) VALVE ASY, 2-SPOOL (W/O FITTINGS) BOLT LOCKNUT WIRE HARNESS - DUAL WING W/ ROPS WIRE HARNESS - RIGHT WING FIRST W/ ROPS WIRE HARNESS - DUAL WING W/CAB WIRE HARNESS - RIGHT WING FIRST W/CAB CAPSCREW LOCKNUT TLM 1/2 NC PLC VALVE STAND - STRAIGHT VALVE STAND - ANGLED IN VALVE STAND - ANGLED OUT HOSE HOSE HOSE HOSE HOSE COVER W/ DECAL CAPSCREW WASHER HOSE ON/OFF SWITCH ON/OFF KNOB 2014 Alamo Group Inc. Parts Section -17

23 CUTTER KNIVES - CC - FC - RENV - PACKAGES & KITS 2014 Alamo Group Inc. Parts Section -18

24 CUTTER KNIVES - CC - FC - RENV - PACKAGES & KITS Continued KNIFE PKG FC STD, PIN MNT` D KN # KNIFE PKG CC STD, RING MNT` KN # KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT KN # KNIFE PKG FC STD, PIN MNT`D KN # KNIFE PKG FC STD, PIN MNT`D KN # KNIFE PKG FC RCK & TRSH, RING MNT`D KN # KNIFE PKG CC STD, RING MNT`D KN # KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT`D KN # KNIFE PKG FC STD, PIN MNT`D KN # KNIFE PKG FC RCK & TRSH, RING MNT`D KN # KNIFE PKG CC STD, RING MNT`D KN # KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT`D KN # KNIFE PKG FC STD, PIN MNT`D KN # KNIFE PKG FC RCK & TRSH, RING MNT`D KN # RING ORDER W/ PKG # RING PIN & COTTER PIN BAG (50 PCS) ORDER W/PKG # KNIFE PKG CC ES HD SHEARED EDGE, RING MNT`D KN # A 1 KNIFE PKG CC ES HD FORGED EDGE, RING MNT`D KN # KNIFE PKG FC 250 PCS KNIFE PKG FC 500 PCS 2014 Alamo Group Inc. Parts Section -19

25 CUTTER KNIVES - CC - FC - RENV - SINGLE & BULK 2014 Alamo Group Inc. Parts Section -20

26 CUTTER KNIVES - CC - FC - RENV - SINGLE & BULK Continued KNIFE, FC PIN MNTD (STD) BULK PKG, 2500 PCS FC KNIFE BULK PKG, 5000 PCS FC KNIFE KNIFE PIN, HEAT TREATED KNIFE, FC RING & CLIP MNTD BULK PKG, 500 PCS FC KNIFE BULK PKG, 2500 PCS FCKNIFE KNIFE RING (USE W/ KNIFE) LOCKNUT, 5/16"-NF PLB (USE W/ KNIFE ) RING CLIP (USE W/ KNIFE ) BOLT, HEX HEAD 5/16"-NF X 7/8" PL GR5 (USE W/ KNIFE ) KNIFE, CC RING MNTD BULK PKG 2500 PCS CC KNIFE BULK PKG 5000 PCS CC KNIFE KNIFE, CC ES HD (SHEARED EDGE) BULK PKG, 2000 PCS CC ES HD KNIFE BULK PKG, 4000 PCS CC ES HD KNIFE KNIFE, CC ES HD (FORGED EDGE) BULK PKG, 2000 PCS CC ES HD KNIFE BULK PKG, 3500 PCS CC ES HD KNIFE KNIFE RING (USE W/ KNIFE , OR ) PIN, HARDENED (USE W/ KNIFE , OR ) COTTER PIN (USE W/ KNIFE , OR ) 2014 Alamo Group Inc. Parts Section -21

27 CYLINDER ASY - LIFT CYL - P/N A A 1 LIFT CYL ASY (W/0 FITTINGS) CYLINDER ROD CYLINDER BARREL CYLINDER HEAD PISTON 5 5JRC NUT 11 * 1 SEAL PISTON COTTER PIN ROD END CLAMP W/ SET SCREW ROD END W/ GREASE FITTING COTTER PIN PIN ELBOW PLUG A 1 CYLINDER (W/O ITEMS 13 & 14) SEAL KIT, (ITEMS 6, 7, 8, 9, Alamo Group Inc. Parts Section -22

28 CYLINDER ASY - TILT CYL - P/N A A 2 TILT CYL W/0 FITTINGS MA CYLINDER ROD CYLINDER HEAD PISTON 5 5JRC NUT 11 * 1 SEAL PISTON COTTER PIN ROD END CLAMP W/ SET SCREW ROD END W/ GREASE FITTING COTTER PIN PIN A 1 CYLINDER SEAL KIT 2014 Alamo Group Inc. Parts Section -23

29 CYLINDER ATTACHMENT - LIFT & TILT 2014 Alamo Group Inc. Parts Section -24

30 CYLINDER ATTACHMENT - LIFT & TILT Continued INNER PIVOT PIN W/GREASE FITTING BOLT LOCKWASHER PIN W/CLIP ROD END CLAMP ROD END W/GREASE FITTING PLUG BUSHING PIVOT W/BUSHING BUSHING GREASE FITTING GREASE FITTING CYLINDER PIN COTTER PIN RIGHT HAND LIFT FRAME (CALL CUSTOMER SERVICE FOR DETAILS) LEFT HAND LIFT FRAME (CALL CUSTOMER SERVICE FOR DETAILS) PIVOT PIN NUT * 1 LIFT STAND - RIGHT HAND (NOT SHOWN) ELBOW, 90 DEG BOLT NUT,TOPLOCK 5/8 NC PLC BOLT LOCKNUT MACHINE SCREW MOUNTING SWITCH SWITCH MAGNET SPACER MOUNTING LH MOUNTING RH A 2 LIFT CYLINDER W/PIN & CLIP A 2 TILT CYLINDER W/PIN & CLIP SPACER BOLT LOCKWASHER PIVOT PIN WIRE HARNESS RIGHT WING WIRE HARNESS LEFT WING 2014 Alamo Group Inc. Parts Section -25

31 DRIVELINE ASY - P/N Alamo Group Inc. Parts Section -26

32 DRIVELINE ASY - P/N Continued DRIVELINE ASY W/CLUTCH & SHIELDS CLUTCH ASY GREASE FITTING UNIVERSAL JOINT OUTER TUBE YOKE OUTER TUBE INNER TUBE INNER TUBE YOKE ROLL PIN YOKE, 1-3/8" GREASE FITTING DRIVELINE WARNING LABEL OUTER HALF W/SLIP CLUTCH INNER HALF SHAFT W/1-3/8-6 YOKE INNER SHIELD BEARING (NEW STYLE) INNER SHIELD BEARING (USE WITH SET SCREW) SCREW A 1 COMPLETE SHIELD DRIVELINE SHIELD WARNING LABEL OUTER SHIELD BEARING (NEW STYLE) OUTER SHIELD BEARING (USE WITH SCREW) Q.D. COLLAR KIT A 1 HALF INNER SHIELD A 1 HALF OUTER SHIELD 2014 Alamo Group Inc. Parts Section -27

33 GEARBOX ASY - P/N Alamo Group Inc. Parts Section -28

34 GEARBOX ASY - P/N Continued GEARBOX ASY PINION SEAL NUT SPRING WASHER BEARING, ROLLER SPACER CIRCLIP, INTERNAL BEARING, ROLLER SHIM SHIM SEAL SHAFT W/ CROWN WHEEL BEARING, BALL BOLT COVER PLUG PLUG, DRAIN HOUSING GASKET 2014 Alamo Group Inc. Parts Section -29

35 HYD SCHEMATIC - CYL HOSE - CONTROL DUAL WING HOSE, CONTROL VALVE TO PUMP HOSE, CONTROL VALVE TO RETURN FILTER HOSE, CONTROL VALVE TO TILT CYL. - LIVE END HOSE, CONTROL VALVE TO TILT CYL. - DEAD END HOSE, CONTROL VALVE TO LIFT CYL. - LIVE END HOSE, CONTROL VALVE TO LIFT CYL. - LIVE END HOSE, CONTROL VALVE TO TILT CYL. - LIVE END 2014 Alamo Group Inc. Parts Section -30

36 THIS PAGE INTENTIONALLY LEFT BLANK 2014 Alamo Group Inc. Parts Section -31

37 HYD SCHEMATIC W/ PARTS - DUAL WING 2014 Alamo Group Inc. Parts Section -32

38 HYD SCHEMATIC W/ PARTS - DUAL WING Continued SUCTION HOSE HOSE, CASE DRAIN - PUMP HOSE, CASE DRAIN - MOTOR HOSE, MOTOR RETURN TO WING COOLING TUBE HOSE, MOTOR RETURN TO WING COOLING TUBE HOSE, SUCTION, GEAR PUMP HOSE, HYD PLUMBING TO MOTOR-PRESSURE-33" LONG HOSE, HYD PLUMBING TO MOTOR-PRESSURE- 62.5" LONG HOSE, WING TO HYD PLUMBING-RETURN-33" LONG HOSE, WING TO HYD PLUMBING-RETURN -65.5" LONG TUBE, MOTOR PRESSURE TUBE, MOTOR RETURN MOUNTING PLATE ADAPTER HYD, 90 DEG BULKHEAD ADAPTER HYD, STRAIGHT BULKHEAD WASHER ADAPTER HYD, SPECIAL TUBE CLAMP SLEEVING (SHORT) 27" LONG SLEEVING (LONG) 57" LONG 25 * 1 SLEEVING ELBOW 90 DEG ADAPTER HYD, 90 DEG HOSE GUARD SIDE PLATE, HOSE GUARD BOLT LOCKNUT FLATWASHER BOLT LOCKNUT TLM 1/2 NC PLC 2014 Alamo Group Inc. Parts Section -33

39 HYD SCHEMATIC W/ PARTS - RIGHT WING FIRST 2014 Alamo Group Inc. Parts Section -34

40 HYD SCHEMATIC W/ PARTS - RIGHT WING FIRST Continued HOSE, SUCTION HOSE, CASE DRAIN - PUMP HOSE, SUCTION - GEAR PUMP CAP, PIPE HOSE, HYD PLUMBING TO MOTOR-PRESSURE-33" LONG HOSE, HYD PLUMBLING TO MOTOR-PRESSURE- 62.5" LONG HOSE, WING TO HYD PLUMBING-RETURN-33" LONG HOSE, WING TO HYD PLUMBING-RETURN 65.5" LONG HOSE, CASE DRAIN - MOTOR PIPE PLUG HOSE, MOTOR RETURN TO WING COLOLING TUBE SLEEVING (SHORT) 27" LONG SLEEVING (LONG) 57" LONG 16 * 1 SLEEVING ADAPTER HYD, ELBOW, 45 DEG ADAPTER HYD, ELBOW, 90 DEG ADAPTER HYD, ELBOW, 45 DEG ADAPTER, STRAIGHT ADAPTER HYD, ELBOW 90 DEG. BOSS TUBE, MOTOR PRESSURE TUBE CLAMP ADAPTER HYD - SPECIAL ADAPTER HYD - STRAIGHT BULKHEAD WASHER ADAPTER HYD, 90 DEG WELDMENT - TUBE MNTG BRCKT HOSE GUARD SIDE PLATE, HOSE GUARD BOLT LOCKNUT FLATWASHER BOLT LOCKNUT TLM 1/2 NC PLC 2014 Alamo Group Inc. Parts Section -35

41 HYD SCHEMATIC W/ PARTS - RIGHT WING ONLY 2014 Alamo Group Inc. Parts Section -36

42 HYD SCHEMATIC W/ PARTS - RIGHT WING ONLY Continued HOSE, SUCTION HOSE, CASE DRAIN - PUMP HOSE, SUCTION - GEAR PUMP CAP, PIPE 8 * 1 HOSE, HYD PLUMBING TO TANK - RETURN HOSE, HYD PLUMBING TO MOTOR-PRESSURE, 33" LG HOSE, HYD PLUMBING TO MOTOR-PRESSURE, 62.5" LG HOSE, WING TO HYD PLUMBING-RETURN, 33" LG HOSE, WING TO HYD PLUMBING RETURN, 65.5" LG HOSE, CASE DRAIN - MOTOR PIPE PLUG HOSE, MOTOR RETURN TO WING COOLING TUBE & CROSSOVER TUBE SLEEVING (SHORT) 27" LONG SLEEVING (LONG) 57" LONG 16 * 1 SLEEVING ADAPTER HYD, ELBOW, 45 DEG ADAPTER HYD, ELBOW, 90 DEG ADAPTER HYD, ELBOW, 45 DEG ADAPTER HYD, STRAIGHT ADAPTER HYD, ELBOW, 90 DEG. BOSS ADAPTER HYD, 90 DEG ADAPTER HYD, ELBOW BULKHEAD ADAPTER HYD, STRAIGHT BULKHEAD CLAMP BRACKET MOUNTING PLATE HOSE GUARD SIDE PLATE, HOSE GUARD BOLT LOCKNUT FLATWASHER BOLT LOCKNUT TLM 1/2 NC PLC 2014 Alamo Group Inc. Parts Section -37

43 HYD TANK ASY - PN Alamo Group Inc. Parts Section -38

44 HYD TANK ASY - PN Continued HYD TANK ASY, W/ FILTER TANK WELDMENT O-RING FILTER ASY, W/ SHORT EXT TUBE LOCKWASHER, 3/8" HIGHCOLLAR BOLT, HEX HEAD 3/8"-NC X 7/8" PL GR GAUGE, SIGHT & TEMPERATURE FILLER CAP & BREATHER ASY STARWASHER #10, EXT TOOTH PL MACHINE SCREW, M5-P0.8 X 12MM PLUG, PIPE,SOCKET HEAD 1/4" PLUG, MAGNETIC 1/2" NPT PLUG, CAP-TEAR TAB 1-1/4" PIPE, CAP 3/4"-14 NPT 2014 Alamo Group Inc. Parts Section -39

45 MOTOR ASY - LEFT WING MANIFOLD RELIEF SOLENOID VALVE - COMPLETE SOLENOID VALVE CARTRIDGE SOLENOID COIL 4 * 1 HOSE, PRESSURE ELBOW CAP NUT STRAIGHT ADAPTER O-RING (NOT SHOWN) ELBOW LOCKWASHER 11 7AH BOLT HOSE-DRAIN HOSE RETURN CROSSOVER ELBOW ADAPTER ADAPTER MOTOR PLUG (NOT SHOWN) WIRE HARNESS LEFT WING 2014 Alamo Group Inc. Parts Section -40

46 MOTOR ASY - RIGHT WING MANIFOLD RELIEF SOLENOID VALVE - COMPLETE SOLENOID VALVE CARTRIDGE SOLENOID COIL 4 * 1 HOSE, PRESSURE ELBOW 6 7AH ADAPTER MOTOR O-RING (NOT SHOWN) ELBOW LOCKWASHER 11 7AH BOLT HOSE-DRAIN HOSE RETURN CROSSOVER ADP TUBE ELBOW 16MJ-16FJX 90DG ELBOW ADAPTER ADAPTER CAP ADAPTER PLUG (NOT SHOWN) WIRE HARNESS RIGHT WING 2014 Alamo Group Inc. Parts Section -41

47 MOTOR REPAIR PARTS - P/N Alamo Group Inc. Parts Section -42

48 MOTOR REPAIR PARTS - P/N Continued MOTOR W/KEY 2.48 CU/IN ROTATING KIT ASY PLATE ASY, BACKING SHAFT, KEYED 4 NFS 1 HOUSING ASY, (NOT FURNISHED AS PARTS) BEARING & RACE SET PLATE, CAM INSERT O-RING HHCS 5/16NC 2 PL WASHER RING, SPIRAL RETAINING RING KIT, SEAL ADAPTER 12A O-RING, 2.0 X 1-13/16 12B SEAL, HIGH PRESSURE 12C SEAL ADAPTER, 2.00 BORE STEP KEY, 1/4 X 5/ PLUG, HEX HD # 8MB BEARING, BACKPLATE BEARING HOUSING SEAL KIT 2014 Alamo Group Inc. Parts Section -43

49 MOTOR REPAIR PARTS - P/N Alamo Group Inc. Parts Section -44

50 MOTOR REPAIR PARTS - P/N Continued MOTOR W/KEY 2.48 CU/IN ROTATING KIT ASY PLATE ASY, BACKING SHAFT, KEYED 4 NFS 1 HOUSING ASY, (NOT FURNISHED AS PARTS) BEARING & RACE SET PLATE, CAM INSERT O-RING HHCS 5/16NC 2 PL WASHER RING, SPIRAL RETAINING RING KIT, SEAL ADAPTER 12A O-RING, 2.0 X 1-13/16 12B SEAL, HIGH PRESSURE 12C SEAL ADAPTER, 2.00 BORE PLUG, HEX HD # 8MB BEARING, BACKPLATE ASY BEARING HOUSING VALVE PLATE SEAL KIT 2014 Alamo Group Inc. Parts Section -45

51 MOWER ASY - LH & RH WING 50 (PART 1) 2014 Alamo Group Inc. Parts Section -46

52 MOWER ASY - LH & RH WING 50 (PART 1) Continued CUTTER HSG WLDMNT, RH 50" WING CUTTER HSG WLDMNT, LH 50" WING MOTOR ASY, WING (SEE HYD MOTOR SWCTâ N) PLATE,MOTOR MOUNT BOLT, HEX HEAD3/8"-16UNC X 1-1/2" PL GR LOCKWASHER, 1/2" HEAVY PULLEY, 2 GRV HUB, 1-1/8 ID 1-13/16LG 1/4 KEY BOLT, HEX HEAD 5/16"-NC X 1-1/4" PL GR5 8A STEP KEY 1/4 X 5/ V-BELTS MATCHED PAIR (2 BELTS) IDLER ARM WLDMNT, RH FWD ROT IDLER ARM WLDMNT, RH REV ROT IDLER ARM WLDMNT, LH REV ROT IDLER ARM WLDMNT, LH FWD ROT IDLER PULLEY BOLT, HEX HEAD 5/16"-NF X 5/8" PL GR FLATWASHER, 5/16 TYPE AW,ZP IDLER BEARING SPACER SPRING, EXTENSION IDLER ASY, RH (FWD ROT) IDLER ASY, LH (FWD ROT) IDLER ASY, RH (REV ROT) IDLER ASY, LH (REV ROT) BELT GUARD WLDMNT, RH FWD ROT BELT GUARD WLDMNT RH REV ROT BELT GUARD WLDMNT LH FWD ROT BELT GUARD WLDMNT, LH REV ROT BOLT, HEX HEAD 3/8"-NF X 3/4" PL GR FLATWASHER, 3/8" PL STD LOCKWASHER, 3/8 MEDIUM-ZP SUPPORT GUARD, TOP CUTTERSHAFT PULLEY KEY, CUTTERSHAFT PULLEY WASHER, 1-3/4" X 33/64" X 1/4" LOCKWASHER, HVY 5/8" BOLT, HEX HEAD 5/8"-NF X 1-1/2" ZP GR BEARING, ASY, CUTTERSHAFT BEARING, CUTTERSHAFT ROLLER WLDMNT, 50", RND KEYED SHAFT CUTTERSHAFT WLDMNT, 50" CC KNIFE 2014 Alamo Group Inc. Parts Section -47

53 MOWER ASY - LH & RH WING 50 (PART 2) 2014 Alamo Group Inc. Parts Section -48

54 MOWER ASY - LH & RH WING 50 (PART 2) Continued... 29A WLDMT. 50 FC CTRSHFT USE KNIFE HD COARSE CUT KNIFE, FINE CUT RING COMPLETE PIN-HARDENED PIN COTTER 1/8 X 3/4 HAMLK KNIFE PIN HEAT TREATED< SHOE/WEAR PLATE CARB 1/2 NC 1-1/2 PL BOLT,PLOW 1/2NC X 1-1/2 GR HIGH ALLOY, L/W 5/16 YZ KG IDLER PIVOT PIN MA GREASE FTG 1/4-28 SHORT THREAD NO. 2 RED LUBRICAPS< BEARING, ASY BEARING,CUTTERSHFT (NON-DRIVE) HEXB 3/8 NC X 1-1/4 PL NUT TOPLOCK 3/8 NC PL HHCS 3/8 NF 1-1/8 PL LOCKWASHER,3/8 EXTERNAL TOOTH FENDER DEFLECTOR-REAR HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB WDMT, FOOT GUARD HHCS 1/2 NC 1 1/4 PL HHCS 1/2-13UNC 1-1/2 PL LOCKNUT TLM 1/2 NC PLC HHCS 5/16NF 7/8 PL CLIP, RING LOCKNUT CLM 5/16 NF PLB FINE CUT RING KNIFE RING ASSY- ROLLER BRG ASY- ROLLER BRG W/HEX BORE HOUSING,BEARING,MACHINED PKG,BRG ASSY W/SETSCREW BEARING-REAR ROLLER W/HEX BORE ASY GREASE FTG 1/ DEG 2014 Alamo Group Inc. Parts Section -49

55 MOWER ASY - LH & RH WING 50 (PART 3) 2014 Alamo Group Inc. Parts Section -50

56 MOWER ASY - LH & RH WING 50 (PART 3) Continued SEAL- ROLLER BRG CARB 1/2 NC 1-3/4 PL LOCKNUT,SP INSET 1/2 NC PLB USE USE OFFSET LOCKING PLATE BOLT, 5/8-11X 2.06 GR5 -UNPLTD NUT,CENTER LOCK,5/8NC,PL Alamo Group Inc. Parts Section -51

57 MOWER ASY - LH & RH WING 62 (PART 1) 2014 Alamo Group Inc. Parts Section -52

58 MOWER ASY - LH & RH WING 62 (PART 1) Continued WLDMT CUTTERHSG RH WLDMT CUTTERHSG LH PLATE,MOTOR MOUNT HHCS 3/8-16UNC 1-1/2 PL LOCKWASHER, 1/2, HVY, PL PULLEY 6.35 OD 2 GRV B SEC USE HHCS 5/16NC 1-1/4 PL5 8A STEP KEY 1/4 X 5/ V-BELTS MATCHED PAIR (2 BELTS) WLDMT,IDLER ARM RIGHT,FWD.ROT WLDMT,IDLER ARM RIGHT,REV. ROT WLDMT,IDLER ARM LEFT,REV. ROT WLDMT,IDLER ARM LEFT,FWD. ROT IDLER PULLEY - INT< HHCS 5/16NF 5/8 PL FLATWASHER 5/16 PL IDLER BEARING SPACER< SPRING,EXTENSION ASSY,IDLER,RH (FWD ROT) ASSY,IDLER,LH (FWD ROT) ASSY,IDLER,RH (REV ROT) ASSY,IDLER,LH (REV ROT) WLDMT- BELT GRD RH FWD ROT WLDMT- BELT GUARD RH RR WLDMT- BELT GRD LH FWD ROT WLDMT,LH,BELT GUARD HHCS 3/8 NF 3/4 PL FLATWASHER STD 3/ HIGH ALLOY, L/W 3/8 YZ SUPPORT, GUARD - TOP NA CUTTERSHAFT PULLEY KEY,PULLEY,CTRSHAFT WASHER,1-3/4 X 33/64 X 1/ LOCKWASHER, 5/8 HVY, KANTLINK HHCS,5/8NF X 1-1/2 ZP BEARING, ASY, CUTTERSHAFT BEARING CUTTERSHAFT WLDMT- ROLLER WLDMT- ROLLER 62 W/HEX SHAFT 2014 Alamo Group Inc. Parts Section -53

59 MOWER ASY - LH & RH WING 62 (PART 2) 2014 Alamo Group Inc. Parts Section -54

60 MOWER ASY - LH & RH WING 62 (PART 2) Continued KIT,ROLLER 60/ CUTTERSHAFT, WA CC 29A CUTTER SHAFT, WA FC USE KNIFE HD COARSE CUT KNIFE, FINE CUT RING COMPLETE PIN-HARDENED PIN COTTER 1/8 X 3/4 HAMLK KNIFE PIN HEAT TREATED< SHOE/WEAR PLATE CARB 1/2 NC 1-1/2 PL BOLT,PLOW 1/2NC X 1-1/2 GR HIGH ALLOY, L/W 5/16 YZ KG IDLER PIVOT PIN MA GREASE FTG 1/4-28 SHORT THREAD NO. 2 RED LUBRICAPS< BEARING, ASY BEARING,CUTTERSHFT (NON-DRIVE) HEXB 3/8 NC X 1-1/4 PL NUT TOPLOCK 3/8 NC PL HHCS 3/8 NF 1-1/8 PL LOCKWASHER,3/8 EXTERNAL TOOTH FENDER DEFLECTOR,TRASH,62 (REAR) WLDMT, FOOT GUARD 62, INT HHCS 1/2 NC 1 1/4 PL HHCS 1/2-13UNC 1-1/2 PL BAR,FLAP RETAINER - 62" REAR LOCKNUT TLM 1/2 NC PLC HHCS 5/16NF 7/8 PL CLIP, RING LOCKNUT CLM 5/16 NF PLB FINE CUT RING KNIFE RING ASSY- ROLLER BRG ASY- ROLLER BRG W/HEX BORE HOUSING,BEARING,MACHINED PKG,BRG ASSY W/SETSCREW BEARING-REAR ROLLER W/HEX BORE ASY GREASE FTG 1/ DEG 2014 Alamo Group Inc. Parts Section -55

61 MOWER ASY - LH & RH WING 62 (PART 3) 2014 Alamo Group Inc. Parts Section -56

62 MOWER ASY - LH & RH WING 62 (PART 3) Continued SEAL- ROLLER BRG CARB 1/2 NC 1-3/4 PL LOCKNUT,SP INSET 1/2 NC PLB USE USE DEFLECTOR,TRASH,62 (FRONT) ASSY,ROLLER BRG/BRKT,LH ASSY,ROLLER BRG/BRKT,RH ASY- ROLLER BRKT LH W/HEX BRG ASY- ROLLER BRKT RH W/HEX BRG OFFSET LOCKING PLATE BOLT, 5/8-11X 2.06 GR5 -UNPLTD NUT,CENTER LOCK,5/8NC,PL BAR FLAP RETAINER 62 FRONT HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB 2014 Alamo Group Inc. Parts Section -57

63 MOWER ASY - LH & RH WING 74 (PART 1) 2014 Alamo Group Inc. Parts Section -58

64 MOWER ASY - LH & RH WING 74 (PART 1) Continued WLDMT,CTRHSG,74-RH WLDMT,CTRHSG,74-LH PLATE,MOTOR MOUNT HHCS 3/8-16UNC 1-1/2 PL HHCS 1/2-13UNC 1-1/2 PL LOCKNUT TLM 1/2 NC PLC LOCKWASHER, 1/2, HVY, PL PULLEY 6.35 OD 2 GRV B SEC USE HHCS 5/16NC 1-1/4 PL HIGH ALLOY, L/W 5/16 YZ KG 8A STEP KEY 1/4 X 5/ V-BELTS MATCHED PAIR (2 BELTS) WLDMT,IDLER ARM RIGHT,FWD.ROT WLDMT,IDLER ARM RIGHT,REV. ROT WLDMT,IDLER ARM LEFT,REV. ROT WLDMT,IDLER ARM LEFT,FWD. ROT IDLER PULLEY - INT< HHCS 5/16NF 5/8 PL HIGH ALLOY, L/W 5/16 YZ KG FLATWASHER 5/16 PL IDLER BEARING SPACER< SPRING,EXTENSION ASSY,IDLER,RH (FWD ROT) ASSY,IDLER,LH (FWD ROT) ASSY,IDLER,RH (REV ROT) ASSY,IDLER,LH (REV ROT) NO. 2 RED LUBRICAPS< WLDMT- BELT GRD RH FWD ROT WLDMT- BELT GUARD RH RR WLDMT- BELT GRD LH FWD ROT WLDMT,LH,BELT GUARD HHCS 3/8 NF 3/4 PL FLATWASHER STD 3/ HIGH ALLOY, L/W 3/8 YZ SUPPORT, GUARD - TOP NA HEXB 3/8 NC X 1-1/4 PL NUT TOPLOCK 3/8 NC PL CUTTERSHAFT PULLEY KEY,PULLEY,CTRSHAFT 2014 Alamo Group Inc. Parts Section -59

65 MOWER ASY - LH & RH WING 74 (PART 2) 2014 Alamo Group Inc. Parts Section -60

66 MOWER ASY - LH & RH WING 74 (PART 2) Continued WASHER,1-3/4 X 33/64 X 1/ LOCKWASHER, 5/8 HVY, KANTLINK HHCS,5/8NF X 1-1/2 ZP BEARING, ASY, CUTTERSHAFT BEARING CUTTERSHAFT WLDMT- ROLLER WLDMT- ROLLER 74 W/HEX SHAFT ASSY- ROLLER CARB 1/2 NC 1-3/4 PL CARB 1/2 NC 1-1/2 PL LOCKNUT TLM 1/2 NC PLC CUTTERSHAFT, CC 29A CUTTERSHAFT, FC WA USE KNIFE HD COARSE CUT KNIFE, FINE CUT RING COMPLETE PIN-HARDENED PIN COTTER 1/8 X 3/4 HAMLK PIN COTTER 1/8 X 3/4 HAMLK KNIFE PIN HEAT TREATED< SHOE/WEAR PLATE CARB 1/2 NC 1-1/2 PL BOLT,PLOW 1/2NC X 1-1/2 GR HIGH ALLOY, L/W 5/16 YZ KG IDLER PIVOT PIN MA GREASE FTG 1/4-28 SHORT THREAD NO. 2 RED LUBRICAPS< BEARING, ASY BEARING,CUTTERSHFT (NON-DRIVE) HEXB 3/8 NC X 1-1/4 PL NUT TOPLOCK 3/8 NC PL HHCS 3/8 NF 1-1/8 PL LOCKWASHER,3/8 EXTERNAL TOOTH FENDER HHCS 1/2-13UNC 1-1/2 PL HHCS 1/2 NC 1 1/4 PL LOCKNUT TLM 1/2 NC PLC DEFLECTOR,TRASH,74 (REAR) HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL 2014 Alamo Group Inc. Parts Section -61

67 MOWER ASY - LH & RH WING 74 (PART 3) 2014 Alamo Group Inc. Parts Section -62

68 MOWER ASY - LH & RH WING 74 (PART 3) Continued NUT TOPLOCK 1/4 NC PLB WLDMT, FOOT GUARD 74, INT HHCS 1/2 NC 1 1/4 PL HHCS 1/2-13UNC 1-1/2 PL BAR FLAP RETAINER 74 REAR HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB LOCKNUT TLM 1/2 NC PLC HHCS 5/16NF 7/8 PL CLIP, RING LOCKNUT CLM 5/16 NF PLB FINE CUT RING KNIFE RING ASSY- ROLLER BRG ASY- ROLLER BRG W/HEX BORE HOUSING,BEARING,MACHINED PKG,BRG ASSY W/SETSCREW BEARING-REAR ROLLER W/HEX BORE ASY GREASE FTG 1/ DEG SEAL- ROLLER BRG CARB 1/2 NC 1-3/4 PL LOCKNUT,SP INSET 1/2 NC PLB USE USE DEFLECTOR,TRASH,74 (FRONT) ASSY,ROLLER BRG/BRKT,LH ASSY,ROLLER BRG/BRKT,RH ASY- ROLLER BRKT LH W/HEX BRG ASY- ROLLER BRKT RH W/HEX BRG OFFSET LOCKING PLATE BOLT, 5/8-11X 2.06 GR5 -UNPLTD NUT,CENTER LOCK,5/8NC,PL BAR FLAP RETAINER 74 FRONT HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB 2014 Alamo Group Inc. Parts Section -63

69 MOWER ASY - LH & RH WING 88 (PART 1) 2014 Alamo Group Inc. Parts Section -64

70 MOWER ASY - LH & RH WING 88 (PART 1) Continued WLDMT-CUTTERHSG RH WLDMT CUTTERHSG LH PLATE,MOTOR MOUNT HHCS 3/8-16UNC 1-1/2 PL LOCKWASHER, 1/2, HVY, PL PULLEY 6.35 OD 2 GRV B SEC USE HHCS 5/16NC 1-1/4 PL5 8A STEP KEY 1/4 X 5/ V-BELTS MATCHED PAIR (2 BELTS) WLDMT,IDLER ARM RIGHT,FWD.ROT WLDMT,IDLER ARM RIGHT,REV. ROT WLDMT,IDLER ARM LEFT,REV. ROT WLDMT,IDLER ARM LEFT,FWD. ROT IDLER PULLEY - INT< HHCS 5/16NF 5/8 PL FLATWASHER 5/16 PL IDLER BEARING SPACER< SPRING,EXTENSION ASSY,IDLER,RH (FWD ROT) ASSY,IDLER,LH (FWD ROT) ASSY,IDLER,RH (REV ROT) ASSY,IDLER,LH (REV ROT) WLDMT- BELT GRD RH FWD ROT WLDMT- BELT GUARD RH RR WLDMT- BELT GRD LH FWD ROT WLDMT,LH,BELT GUARD HHCS 3/8 NF 3/4 PL FLATWASHER STD 3/ HIGH ALLOY, L/W 3/8 YZ SUPPORT, GUARD - TOP NA CUTTERSHAFT PULLEY KEY,PULLEY,CTRSHAFT WASHER,1-3/4 X 33/64 X 1/ LOCKWASHER, 5/8 HVY, KANTLINK HHCS,5/8NF X 1-1/2 ZP BEARING, ASY, CUTTERSHAFT BEARING CUTTERSHAFT WLDMT- ROLLER WLDLMT- ROLLER 88 W/HEX SHAFT 2014 Alamo Group Inc. Parts Section -65

71 MOWER ASY - LH & RH WING 88 (PART 2) 2014 Alamo Group Inc. Parts Section -66

72 MOWER ASY - LH & RH WING 88 (PART 2) Continued ASY,ROLLER CUTTERSHAFT, CC WA 29A CUTTERSHAFT, BLANK USE KNIFE HD COARSE CUT KNIFE, FINE CUT RING COMPLETE PIN-HARDENED PIN COTTER 1/8 X 3/4 HAMLK KNIFE PIN HEAT TREATED< SHOE/WEAR PLATE CARB 1/2 NC 1-1/2 PL BOLT,PLOW 1/2NC X 1-1/2 GR HIGH ALLOY, L/W 5/16 YZ KG IDLER PIVOT PIN MA GREASE FTG 1/4-28 SHORT THREAD NO. 2 RED LUBRICAPS< BEARING, ASY BEARING,CUTTERSHFT (NON-DRIVE) HEXB 3/8 NC X 1-1/4 PL NUT TOPLOCK 3/8 NC PL HHCS 3/8 NF 1-1/8 PL LOCKWASHER,3/8 EXTERNAL TOOTH FENDER DEFLECTOR,TRASH,88 (REAR) WLDMT, FOOT GUARD 88, INT HHCS 1/2 NC 1 1/4 PL HHCS 1/2-13UNC 1-1/2 PL BAR,FLAP RETAINER - 88" REAR LOCKNUT TLM 1/2 NC PLC HHCS 5/16NF 7/8 PL CLIP, RING LOCKNUT CLM 5/16 NF PLB FINE CUT RING KNIFE RING ASSY- ROLLER BRG ASY- ROLLER BRG W/HEX BORE HOUSING,BEARING,MACHINED PKG,BRG ASSY W/SETSCREW BEARING-REAR ROLLER W/HEX BORE ASY GREASE FTG 1/ DEG 2014 Alamo Group Inc. Parts Section -67

73 MOWER ASY - LH & RH WING 88 (PART 3) 2014 Alamo Group Inc. Parts Section -68

74 MOWER ASY - LH & RH WING 88 (PART 3) Continued SEAL- ROLLER BRG CARB 1/2 NC 1-3/4 PL LOCKNUT,SP INSET 1/2 NC PLB USE USE DEFLECTOR,TRASH,88 (FRONT) ASSY,ROLLER BRG/BRKT,LH ASSY,ROLLER BRG/BRKT,RH ASY- ROLLER BRKT LH W/HEX BRG ASY- ROLLER BRKT RH W/HEX BRG OFFSET LOCKING PLATE BOLT, 5/8-11X 2.06 GR5 -UNPLTD NUT,CENTER LOCK,5/8NC,PL BAR FLAP RETAINER 88 FRONT HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB 2014 Alamo Group Inc. Parts Section -69

75 MOWER ASY - REAR 88 (PART 1) 2014 Alamo Group Inc. Parts Section -70

76 MOWER ASY - REAR 88 (PART 1) Continued WLDMT,CTRHSG,88-CTR WLDMT CTRHSG 88 W/CASTER WLDMT CTRHSG 88 OFFST RT WLDMT CTRHSG 88 OR 6.5 W/BRKTS WLDMT-CTRHSG 88 O.R WLDMT CTRHSG 88-OR 8.5 W/BRKTS WLDMT CTRHSG 88 O.R WLDMT-CTRHSG 88 OR 14.5 W/BKTS WLDMT CTRHSG 88 OR WLDMT CTRHSG 88 OR 20.5 W/BRKT WLDMT CTRHSG 88 RENOV W/BRKTS WLDMT CTRHSG 88 RENV W/BRAKTS ASSY,SHLD (D/L) HHCS 3/8 NC X 3/4 PL T49 IH QUICK COTTER< WLDMT,OVERARM ASSY HEXB,5/8 NC X 2-1/4 GRD5 ZP HHCS 5/8 NC 1-3/4 PL NUT,TOPLOCK 5/8 NC PLC HHCS 3/4 NC 3-3/4 PL A-FRAME, SPACER NUT 3/4-NC TOPLOCK GRC PL PIN, HITCH A-FRAME WLDMT,GRBX MNTG FRAME GEARBOX, OILED & TESTED BANJO ASSY 88 CENTER,FWD/REV BANJO 74 CT/F/R,88 OR6.5 FWD BANJO ASSY 88 OFFSET 8.5 FWD BANJO,74 OR8,88 OR14.5 FWD BANJO,74 OR14;99OR20.5 FWD USE USE COUPLER, W/ZERK, SPLINED SHAFT EXTENSION EXTENSION SHAFT OUTPUT SHAFT EXT 6< OUTPUT SHAFT EXT 5< OUTPUT SHAFT EXT EXTENSION SHAFT HSG< EXTENSION SHAFT HSG< 2014 Alamo Group Inc. Parts Section -71

77 MOWER ASY - REAR 88 (PART 2) 2014 Alamo Group Inc. Parts Section -72

78 MOWER ASY - REAR 88 (PART 2) Continued EXTENSION SHAFT HSG EXT SHFT HSG 60 WA OFFSET EXT SHAFT HSG SCREW, FLNG HD 12PT, CTR-BORE HIGH ALLOY, L/W 3/8 YZ RETAINING RING OUTPUT BEVEL RING BALL BEARING 1-1/8 BORE CYL OD HOUSING AND BEARING ASSEMBLY HHCS 3/8-16UNC 1-1/2 PL BEARING HOUSING W/ZERK ASSY RETAINING RING PULLEY SHIM< PULLEY, 8.99 DIA X BORE KEY,DRIVE PULLEY WASHER,BRG 1-7/16X33/64X3/ HHCS 1/2 NF X 1-1/2 PL BELT BRACKET,MOUNTING,SHIELD TUBE,SPACER,LOWER ARM CLIP (LYNCH PIN), 13/32 DIA TUBE,SPACER,UPPER ARM HITCH PIN SPRING,EXTENSION IDLER BEARING SPACER< HHCS 5/16NF 5/8 PL HIGH ALLOY, L/W 5/16 YZ KG ASSY,IDLER ARM (SHD) ASSY,IDLER ARM (SHD-RR) ASSY,OUTBRD BRG PLATE (SHD) ASSY,OUTBRD BRG PLATE (SHD-RR) HHCS 3/8NC X 2-1/4 PL HHCS 3/8 NC 7/8 PL NUT HEX 3/8 NC PL WLDMT-IDLER ARM IDLER ARM W.A PIN,COTTER 3/16 X 1-1/2 PLATED PULLEY,IDLER PKG,SHPG,BELT GUARD (SHD) BELT GD. SHIPPING PKG HHCS 1/2 NC X 1 PL Alamo Group Inc. Parts Section -73

79 MOWER ASY - REAR 88 (PART 3) 2014 Alamo Group Inc. Parts Section -74

80 MOWER ASY - REAR 88 (PART 3) Continued HHCS - 1/2 NF X 1 GR LOCKWASHER, 1/2, HVY, PL FLATWASHER STD 7/16 PL WLDMT- ROLLER ASY,ROLLER WLDLMT- ROLLER 88 W/HEX SHAFT DRIVELINE,S60 W/8 CLUTCH CUTTERSHAFT, CC WA 42A CUTTERSHAFT, BLANK RING COMPLETE PIN-HARDENED USE KNIFE,EXTREME SERVICE KNIFE HD COARSE CUT USE RENOVATING KNIVE PKG 88CC EXTREME SERVICE, KNIFE, PKG SHOE/WEAR PLATE BOLT,PLOW 1/2NC X 1-1/2 GR BEARING, ASY, CUTTERSHAFT BEARING CUTTERSHAFT PULLEY 8-3/4-1-15/16 BORE< KEY,PULLEY,CTRSHAFT WASHER, CUTTERSHAFT LOCKWASHER, 5/8 HVY, KANTLINK HHCS,5/8NF X 1-1/2 ZP ASSY- ROLLER BRG ASY- ROLLER BRG W/HEX BORE HOUSING,BEARING,MACHINED PKG,BRG ASSY W/SETSCREW BEARING-REAR ROLLER W/HEX BORE ASY GREASE FTG 1/ DEG SEAL- ROLLER BRG CARB 1/2 NC 1-3/4 PL NO. 2 RED LUBRICAPS< WLDMT, FOOT GUARD 88, SHD HHCS 1/2-13UNC 1-3/4 PL DEFLECTOR,TRASH,88 (REAR) HHCS 5/16NF 7/8 PL CLIP, RING 2014 Alamo Group Inc. Parts Section -75

81 MOWER ASY - REAR 88 (PART 4) 2014 Alamo Group Inc. Parts Section -76

82 MOWER ASY - REAR 88 (PART 4) Continued LOCKNUT CLM 5/16 NF PLB RING FINE CUT RING KNIFE USE KNIFE PIN HEAT TREATED< PIN COTTER 1/8 X 3/4 HAMLK KNIFE, FINE CUT KIT, 226 FC KNIVES&COTTERPINS H387 RNVTG KN PKG FLATWASHER 5/16 PL HHCS 3/8 NC 1-1/8 PL NUT TOPLOCK 3/8 NC PL FENDER HHCS 1/2-13UNC 1-1/2 PL HHCS 1/2 NC 1 1/4 PL LOCKNUT TLM 1/2 NC PLC BEARING, ASY BEARING,CUTTERSHFT (NON-DRIVE) DEFLECTOR,TRASH,88 (FRONT) HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB USE USE ASSY,ROLLER BRG/BRKT,LH ASSY,ROLLER BRG/BRKT,RH ASY- ROLLER BRKT LH W/HEX BRG ASY- ROLLER BRKT RH W/HEX BRG CARB 1/2 NC 1-1/2 PL LOCKNUT,SP INSET 1/2 NC PLB BAR,FLAP RETAINER - 88" REAR BAR FLAP RETAINER 88 FRONT 2014 Alamo Group Inc. Parts Section -77

83 MOWER ASY - REAR 96 (PART 1) 2014 Alamo Group Inc. Parts Section -78

84 MOWER ASY - REAR 96 (PART 1) Continued WLDMT,CTRHSG,96-CTR ASSY,SHLD (D/L) HHCS 3/8NC X 3/4 PL T49 IH QUICK COTTER< WLDMT,OVERARM ASSY HEXB,5/8 NC X 2-1/4 GRD5 ZP USE NUT,TOPLOCK 5/8 NC PLC HHCS 3/4 NC 3-3/4 PL A-FRAME, SPACER NUT 3/4-NC TOPLOCK GRC PL PIN, HITCH A-FRAME WDMT,GEARBOX MOUTING FRAME WLDMT,GRBX MNTG FRAME GEARBOX, OILED & TESTED BANJO ASY 96 CENTER,FWD/REV ASSY,GRBX-EXT.SHFT-BRG(BANJO) USE USE SHIM BEARING CUP (07100) SHAFT,OUTPUT FOR SH SHAFT,OUTPUT FOR SH88,OR WLDMT,HSG,EXT.SHFT,OFFSET WLDMT,HSG,EXT.SHFT,OFFSET SCREW, FLNG HD 12PT, CTR-BORE LOCKWASHER 3/8 MED KANTLINK OUTPUT BEVEL RING RETAINING RING BALL BEARING 1-1/8 BORE CYL OD HOUSING AND BEARING ASSEMBLY HHCS,3/8NC X 1-1/2 ZP BEARING HOUSING W/ZERK ASSY RETAINING RING PULLEY SHIM< PULLEY, 8.99 DIA X BORE KEY,DRIVE PULLEY WASHER,BRG 1-7/16X33/64X3/ Alamo Group Inc. Parts Section -79

85 MOWER ASY - REAR 96 (PART 2) 2014 Alamo Group Inc. Parts Section -80

86 MOWER ASY - REAR 96 (PART 2) Continued HHCS 1/2 NF X 1-1/2 PL BELT BRACKET,MOUNTING,SHIELD TUBE,SPACER,UPPER ARM CLIP (LYNCH PIN), 13/32 DIA TUBE,SPACER,LOWER ARM HITCH PIN SPRING,EXTENSION IDLER BEARING SPACER< HHCS 5/16NF 5/8 PL LOCKWASHER 5/16 MED KANTLINK FLATWASHER,5/16,TYPE AW,ZP ASSY,OUTBRD BRG PLATE (SHD) ASSY,OUTBRD BRG PLATE (SHD-RR) HHCS 3/8NC X 2-1/4 PL HHCS 3/8 NC 7/8 PL NUT,3/8 NC HEX WLDMT-IDLER ARM IDLER ARM W.A PIN COTTER 3/16 X 1-1/ PULLEY,IDLER ASSY,IDLER ARM (SHD) ASSY,IDLER ARM (SHD-RR) PKG,SHPG,BELT GUARD (SHD) BELT GD. SHIPPING PKG HHCS 1/2 NC X 1 PL HHCS - 1/2 NF X 1 GR USE FLATWASHER,7/16,TYPE AW,ZP FENDER,GUARD (SHD) WLDMT,GUARD FENDER (SHD-RR) SPACER-CUTTERSHAFT- SHD WLDMT,ROLLER WLDMT- ROLLER 96 W/HEX SHAFT DRIVELINE,S60 W/8 CLUTCH CUTTERSHAFT, WA CUTTERSHAFT, WA VERSA PRO RING COMPLETE PIN-HARDENED USE KNIFE HD COARSE CUT 2014 Alamo Group Inc. Parts Section -81

87 MOWER ASY - REAR 96 (PART 3) 2014 Alamo Group Inc. Parts Section -82

88 MOWER ASY - REAR 96 (PART 3) Continued A 1 PKG,KNIFE,HD CC,96 (108381) SHOE/WEAR PLATE USE BOLT,PLOW 1/2NC X 1-1/2 GR WLDMT,HOUSING SHOE (RENV) BEARING, ASY, CUTTERSHAFT BEARING CUTTERSHAFT NUT TOPLOCK 3/8 NC PL PULLEY 8-3/4-1-15/16 BORE< KEY,PULLEY,CTRSHAFT WASHER, CUTTERSHAFT LOCKWASHER, 5/8 HVY, KANTLINK HHCS,5/8NF X 1-1/2 ZP ASSY- ROLLER BRG ASY- ROLLER BRG W/HEX BORE WLDMT, SKID BAR PF PKG,BRG ASSY W/SETSCREW BEARING-REAR ROLLER W/HEX BORE ASY GREASE FTG 1/ DEG SEAL- ROLLER BRG CARB 1/2 NC 1-3/4 PL NO. 2 RED LUBRICAPS< WLDMT, FOOT GUARD 96 SHD DEFLECTOR,TRASH,96 (REAR) USE HHCS 5/16NF 7/8 PL CLIP, RING LOCKNUT CLM 5/16 NF PLB RING FINE CUT RING KNIFE KNIFE PIN HEAT TREATED< /8X3/4 HAMMERLOCK COTTERPN< KNIFE, FINE CUT HHCS 3/8 NC 1-1/8 PL FENDER HHCS 1/2NC X 1-1/2 PL HHCS 1/2 NC X 1-1/4 PL BEARING, ASY 2014 Alamo Group Inc. Parts Section -83

89 MOWER ASY - REAR 96 (PART 4) 2014 Alamo Group Inc. Parts Section -84

90 MOWER ASY - REAR 96 (PART 4) Continued BEARING,CUTTERSHFT (NON-DRIVE) DEFLECTOR,TRASH 96 FRONT HHCS 1/4 NC 1-1/4 PL FLATWASHER STD 1/4 PL NUT TOPLOCK 1/4 NC PLB USE USE ASSY,ROLLER BRG/BRKT,LH ASSY,ROLLER BRG/BRKT,RH ASY- ROLLER BRKT LH W/HEX BRG ASY- ROLLER BRKT RH W/HEX BRG CARB 1/2 NC 1-1/2 PL HHCS 1/2-13UNC 1-3/4 PL LOCKNUT TLM 1/2 NC PLC BAR FLAP RETAINER 96 REAR BAR FLAP RETAINER 96 FRONT 2014 Alamo Group Inc. Parts Section -85

91 OPTIONAL CASTER WHEELS - REAR MOWER LAMINATED PKG,180 LAM. CSTR WHL,FLD INSTL M 1 PKG,360 LAM. CSTR WHL FLD INSTL PKG,CSTR,180 LAM PKG,CTR,360 LAM LOCKWASHER,1/2 PLATED RH CASTER BRACKET LH CASTER BRACKET M 2 CASTER, SOCKET ASY W/ZERK CASTER SOCKET ASSY W/ZERK HHCS 1/2-13UNC 1-3/4 PL UT 1/2 NC HEX PL WASHER,1-3/4 X 33/64 X 1/ HALF FORK COMP C 2 HUB W/BRG CUPS&GREASE FITTING BOLT,HHCS 1/2 NF X 1 PL E 2 SEAL BEARING CONE 1" ID H 2 ASY,WHEEL & TIRE 2014 Alamo Group Inc. Parts Section -86

92 OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 1) CASTER WHEEL PKG, PNEUMATIC 180` SWIVEL, FIELD INSTALL M 1 CASTER WHEEL PKG, PNEUMATIC 360` SWIVEL, FIELD INSTALL PKG CSTR 180 PNEU PKG.CSTR 360 PNEU CSTR BRKT RH, FIELD INSTALL CSTR BRKT LH, FIELD INSTALL M 2 CSTR SCKT ASY W/ZERK 360 DEG CSTR SCKT ASY W/ZERK 180 DEG BOLT LOCKWASHER NUT BOLT LOCKWASHER WASHER CSTR HALF FORK, LH OR RH HUB, W/ BRG CUPS BEARING CUP NUT LUG 1/2 NF SPACER SEAL BEARING CONE 2014 Alamo Group Inc. Parts Section -87

93 OPTIONAL CASTER WHEELS - REAR MOWER PNEUMATIC (PART 2) WASHER NUT, SLOTTED COTTER PIN HUB CAP HUB COMPLETE, (ITEMS ,18) FORK ASY, LOWER (ITEMS 8,9,12-18) WHEEL, (TUBE TYPE TIRE) TUBE, (TUBE TYPE TIRE) TIRE, (TUBE TYPE) WHEEL, TIRE & TUBE ASY 2014 Alamo Group Inc. Parts Section -88

94 OPTIONAL EQUIPMENT - ACCESSORIES - PACKAGES OPTIONAL EQUIPMENT KNIFE GRINDER SET OF KNIFE STRGHTNG BARS " WING MOWER ROLLER SCRAPER KIT ROLLER,62 RUBBER (REPL BY) ROLLER, USE & " WING MOWER ROLLER SCRAPER KIT ROLLER,74 RUBBER (REPL BY) ROLLER, USE & " WING & REAR MOWER ROLLER SCRAPER KIT ROLLER,88 RUBBER (REPL BY) ROLLER, ASY, RUBBER " & 96" REAR MOWER 2014 Alamo Group Inc. Parts Section -89

95 PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 1) 2014 Alamo Group Inc. Parts Section -90

96 PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 1) Continued THUMB SCREW 1/4-20UNC-3/4LG FLATWASHER STD 1/4 PL HEXB 1/2 NC 2 PL LOCKNUT TLM 1/2 NC PLC CAP, ASY, FILLER/BREATHER DIAL INDICATOR-IN TANK FILTER NUT TOPLOCK 3/8 NC PL O-RING LOCKWASHER, 3/8, HVY, PL HHCS 3/8 NC 7/8 PL FILTER ASSY W/ SHORT EXT TUBE FILTER ELEMENT SPRING FILTER CARTRIDGE VALVE FILTER BYPASS FOR MPF FILTER COVER,FOR O-RING SEAL KIT FOR KIT NUTS AND BOLTS FOR ADAPTER PIPE,1-1/4 CLOSE NIPPL ADP PIPE TEE 1-1/4FP ADP PIPE,REDUCER,20MP-16FP BUSHING-REDUCER 16MP-8FP REBUILT CYLINDER HEADOL EXCH ADP HYD ELBOW 20MP -20MJIC ADP HYD 20MP - 20MJ 45? REBUILT CYLINDER HEADOL EXCH GAUGE,SIGHT/TEMPERATURE THERMOMETER DEGREE HEXB 3/8 NC X 1-1/4 PL BRACKET, BELT TENSION FLATWASHER STD 3/ PULLEY 9/16 BORE 1/8 X 3/16 KW WLDMT,PULLEY 7/8-13 SPLINE REBUILT CYLINDER HEADOL EXCH REBUILT CYLINDER HEADOL EXCH REBUILT CYLINDER HEADOL EXCH HOSE #6-6FJX - 4MP - 19LG HOSE CLAMP FOR #12 HOSE FITG HOSE BIB #12HOSE-#12MP REBUILT CYLINDER HEADOL EXCH BEARING 7/8" INTERSTATER D/L 2014 Alamo Group Inc. Parts Section -91

97 PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 2) 2014 Alamo Group Inc. Parts Section -92

98 PUMP & TANK ASY - SINGLE PUMP - SINGLE WING (PART 2) Continued BEARING 1" INTERSTATER D/L ADP,PIPE,COUPLER,12FP-12FP WLDMT, TANK INTERSTATER PUMP-WEBSTER 43YB032-2L HHCS 3/8 NF 7/8 PL HIGH ALLOY, L/W 3/8 YZ HOSE CLAMP,1-5/16 TO 2-1/ HOSE BIB FITTING- 20MP-20 HOSE ADP,PIPE,20FP-20FP,90DEG HOSE #20-20FJX90-BLANK-13LG HHCS 1/2NC X 1-1/2 PL LOCKWASHER, 1/2, HVY, PL ASSY,SINGLE FRONT PUMP 2.77CID ASSY,SINGLE FRONT PUMP 2.28CID KEY 1/8 X 3/16 X 1 LONG REBUILT CYLINDER HEADOL EXCH WLDMT,BUMPER TANK COVER WLDMT. INT ADP HYD ELBOW 12FPX- 8MP BELT,DRIVE (5L260) ADP HYD ELBOW 4MP-4FP ADP HYD,6MB-6MJ,STRAIGHT PLUG, PIPE 1/4 NPTM STANDARD ADP HYD ELBOW 16MJ -16FJX ADP HYD ELBOW 4MP - 6MJ ADP HYD ELBOW 16MB -16MJ ADP HYD ELBOW 20MB -20MJ PIPE CAP 20 FP STARWSHR #10 EXT TOOTH TY A PL MACH METRIC 5-P0.8-12MM 2014 Alamo Group Inc. Parts Section -93

99 PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 1) 2014 Alamo Group Inc. Parts Section -94

100 PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 1) Continued THUMB SCREW 1/4-20UNC-3/4LG FLATWASHER STD 1/4 PL HEXB 1/2 NC 2 PL LOCKNUT TLM 1/2 NC PLC CAP, ASY, FILLER/BREATHER DIAL INDICATOR-IN TANK FILTER NUT TOPLOCK 3/8 NC PL O-RING LOCKWASHER 3/8 HIGHCOLLAR HHCS 3/8 NC 7/8 PL FILTER ASSY W/ SHORT EXT TUBE FILTER ELEMENT SPRING FILTER CARTRIDGE VALVE FILTER BYPASS FOR MPF FILTER COVER,FOR O-RING SEAL KIT FOR KIT NUTS AND BOLTS FOR ADAPTER PIPE,1-1/4 CLOSE NIPPL ADP PIPE TEE 1-1/4FP ADP PIPE,REDUCER,20MP-16FP REDUCER BUSHING 16MP-8FP REBUILT CYLINDER HEADOL EXCH ADP HYD ELBOW 20MP -20MJIC ADP HYD 20MP - 20MJ 45? REBUILT CYLINDER HEADOL EXCH GAUGE,SIGHT/TEMPERATURE THERMOMETER DEGREE HEXB 3/8 NC X 1-1/4 PL BRACKET, BELT TENSION FLATWASHER STD 3/ PULLEY 9/16 BORE 1/8 X 3/16 KW ASSY,PULLEY PIN,SPIROL 3/8 X 1-1/ REBUILT CYLINDER HEADOL EXCH REBUILT CYLINDER HEADOL EXCH HOSE #6-6FJX - 4MP - 13LG REBUILT CYLINDER HEADOL EXCH HOSE CLAMP FOR #12 HOSE FITG HOSE BIB #12HOSE-#12MP REBUILT CYLINDER HEADOL EXCH Alamo Group Inc. Parts Section -95

101 PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 2) 2014 Alamo Group Inc. Parts Section -96

102 PUMP & TANK ASY - TANDEM PUMP - DUAL WINGS (PART 2) Continued BEARING 7/8" INTERSTATER D/L BEARING 1" INTERSTATER D/L ADP,PIPE,COUPLER,12FP-12FP WLDMT, TANK INTERSTATER PUMP-WEBSTER 43YB032-2L HHCS 3/8 NF 7/8 PL HIGH ALLOY, L/W 3/8 YZ HOSE CLAMP,1-5/16 TO 2-1/ HOSE BIB FITTING- 20MP-20 HOSE ADP,PIPE,20FP-20FP,90DEG ADP HYD ELBOW 6MB-6MJ HOSE #20-20FJX90-BLANK-13LG MAGNETIC PLUG 1/2 NPTM ADP HYD STGHT 20MB -20MJ HHCS 1/2-13UNC 1-1/2 PL LOCKWASHER, 1/2, HVY, PL ASSY,TANDEM FRONT PUMP 2.77CID ASSY,TANDEM FRONT PUMP 2.28CID ADP HYD STGHT 16MB-16MJ REBUILT CYLINDER HEADOL EXCH REBUILT CYLINDER HEADOL EXCH KEY 1/8 X 3/16 X 1 LONG ADP HYD ELBOW 16MB -16MJ WLDMT,BUMPER TANK COVER WLDMT. INT ADP HYD ELBOW 12FPX- 8MP BELT,DRIVE (5L260) ADP HYD ELBOW 4MP-4FP ADP HYD ELBOW 20MB -20MJ ADP HYD ELBOW 20MJ -20FJX STARWSHR #10 EXT TOOTH TY A PL MACH METRIC 5-P0.8-12MM 2014 Alamo Group Inc. Parts Section -97

103 PUMP ASY - SINGLE PUMP - SINGLE WING 2014 Alamo Group Inc. Parts Section -98

104 PUMP ASY - SINGLE PUMP - SINGLE WING Continued PUMP ASY, SINGLE FRONT 2.77 CID PUMP ASY, SINGLE FRONT 2.28 CID ROTATING KIT ASY BACKPLATE ASY SPLINED DRIVESHAFT HOUSING ASY W/B EARINGS THRUST BEARING & RACE SET CAMPLATE INSERT "O" RING BOLT, HEX HEAD WASHER RETAINING RING RETAINING RING SHAFT SEAL BEARING, BACKPLATE BEARING, HOUSING SEAL KIT (REPLACES P/N ) 2014 Alamo Group Inc. Parts Section -99

105 PUMP ASSY,TANDEM FRONT PUMP 2.77CID ASSY,PUMP REAR SECTION 2.77CID ASSY,PUMP FRNT SECTION 2.77CID COUPLER O-RING, 2.77CID,TANDEM PUMP CAPSCREW RING, LOCK 2014 Alamo Group Inc. Parts Section -100

106 PUMP ASY - TANDEM FRONT PUMP - DUAL WINGS PUMP ASY, FRNT SECTION 2.77CID ROTATING KIT ASY (F/ FRONT OR REAR PUMP BACK UP PLATE ASY W/BRG (F/ FRONT PUMP) SHAFT, SPLINED (F/ FRONT PUMP) 4 NFS 1 HOUSING ( NOT FURNISHED AS PARTS) BEARING 6 * 1 SHAFT SEAL (IN SEAL KIT) CAMPLATE INSERT 8 * 1 O-RING (IN SEAL KIT) BOLT, HEX HEAD 5/ WASHER 11 * - RETAINING RING (IN SEAL KIT) 12 * - RETAINING RING (IN SEAL KIT) BEARING,BACKPLATE ASY BEARING,HOUSING ASY KIT,PUMP SEAL KIT 2014 Alamo Group Inc. Parts Section -101

107 PUMP ASY - TANDEM REAR PUMP - DUAL WINGS PUMP ASY, REAR SECTION 2.77CID ROTATING KIT ASY (F/ FRONT OR REAR PUMP BACK UP PLATE ASY W/BRG (F/ REAR PUMP) SHAFT, SPLINED (F/ REAR PUMP) 4 NFS 1 HOUSING ( NOT FURNISHED AS PARTS) BEARING 6 * - SHAFT SEAL (IN SEAL KIT) CAMPLATE INSERT 8 * - O-RING (IN SEAL KIT) BOLT, HEX HEAD WASHER 11 * - RETAINING RING (IN SEAL KIT) 12 * - RETAINING RING (IN SEAL KIT) BEARING,BACKPLATE ASY BEARING,HOUSING ASY KIT,PUMP SEAL KIT 2014 Alamo Group Inc. Parts Section -102

108 PUMP ASY, GEAR TYPE - FRONT - HYD CYL SUPPLY PN GEAR PUMP ASY 1 * 1 SHAFT SEAL 2 * 1 GASKET INSERT KIT, SEAL/GASKET/BEARING 2014 Alamo Group Inc. Parts Section -103

109 TUBING ASY HYD - DUAL WING ASY P/N MOUNTING PLATE TUBE, MOTOR RETURN TUBE, MOTOR PRESSURE BULKHEAD FITTING 90 DEG CLAMP BULKHEAD FITTING STRAIGHT WASHER ADAPTER, SPECIAL SPACER (NOT SHOWN) 2014 Alamo Group Inc. Parts Section -104

110 TUBING ASY HYD - SINGLE WING - ASY P/N MNTG PLATE & TUBING ASY,HYD.PLBG, SINGLE WING MOUNTING PLATE TUBE, MOTOR PRESSURE TUBE CLAMP BULKHEAD FITTING 90 DEG CAP FITTING #16FJIC (NOT SHOWN) BULKHEAD FITTING, STRAIGHT SPACER, (NOT SHOWN) 2014 Alamo Group Inc. Parts Section -105

111 THIS PAGE INTENTIONALLY LEFT BLANK 2014 Alamo Group Inc. Parts Section -106

112 VALVE REMOTE CONTROL 2014 Alamo Group Inc. Parts Section -107

113 VALVE REMOTE CONTROL Continued BRACKET, ARM REST MOUNT PLATE, MOUNT EXTENSION BRACKET, PIVOT PLATE MOUNT WELDMENT, SWITCH MOUNT ASSEMBLY, SINGLE AXIS CONTROL STICK ASSEMBLY, ARM REST WELDMENT, BRACKET-VALVE CONNECT BOLT (2-HANDLE) BOLT (4-HANDLE) FLAT WASHER BOLT BOLT BOLT FLATWASHER BOLT LOCKNUT LOCKNUT ROLL PIN CLEVIS NUT SWITCH, PUSH PULL KNOB PIVOT PLATE WELDMENT DECAL, ON/OFF SWITCH WIRE HARNESS KIT (NOT SHOWN) 2014 Alamo Group Inc. Parts Section -108

114 WIRE HARNESS - DUAL WINGS TERMINAL RING SPADE TERMINAL, OUTER SPADE TERMINAL, INNER WIRE HARNESS ASY, RIGHT WING ONLY WIRE HARNESS ASY, LEFT WING ONLY WIRE HARNESS ASY COMPLETE, F/ ROPS TRACTOR WIRE HARNESS ASY COMPLETE, F/ CAB TRACTOR CONNECTOR, W/ GASKET & SCREW BUTT CONNECTOR, GA CONNECTOR GASKET 2014 Alamo Group Inc. Parts Section -109

115 WIRE HARNESS - RH WING - FIRST OR ONLY TERMINAL RING SPADE TERMINAL, OUTER SPADE TERMINAL, INNER WIRE HARNESS ASY, RIGHT WING WIRE HARNESS ASY COMPLETE, F/ ROPS TRACTOR WIRE HARNESS ASY COMPLETE, F/ CAB TRACTOR CONNECTOR, W/ GASKET & SCREW BUTT CONNECTOR, GA CONNECTOR GASKET 2014 Alamo Group Inc. Parts Section -110

116

117 TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manuals thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT ( Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER 1. Provide a Roll-Over-Protective Structure that meets the requirements of this standard. 2. Provide seat belts that meet the requirements of this paragraph of this standard and SAE J4C. 3. Ensure that each employee uses such seat belt while the tractor is moving. 4. Ensure that each employee tightens the seat belt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seat belt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going, especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly, no jerky turns, starts, or stops. 8. Hitch only to the draw bar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.

118 ALAMO INDUSTRIAL Limited Warranty 1. Limited Warranties Alamo industrial warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser ( purchaser ) and warrants for six months to the original commercial or industrial purchaser ( purchaser ) that the goods purchased are free from defects in material or workmanship Manufacturer will replace for the purchaser any part or parts found, upon examination at one of its factories, to be defective under normal use and service due to defects in material or workmanship This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use, negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found in your operator s manual Except as provided herein, no employee, agent, dealer, or other person is authorized to give any warranties of any nature on behalf of manufacturer. 2. Remedies And Procedures This limited warranty is not effective unless the purchaser returns the registration and warranty form to manufacturer within 30 days of purchase Purchaser claims must be made in writing to the authorized dealer ( dealer ) from whom purchaser purchased the goods or an approved authorized dealer ( dealer ) within 30 days after purchaser learns of the facts on which the claim is based Purchaser is responsible for returning the goods in question to the dealer If after examining the goods and/or parts in question, manufacturer finds them to be defective under normal use and service due to defects in material or workmanship, manufacturer will: (A) repair or replace the defective goods or part(s) or (B) reimburse purchaser for the cost of the part(s) and reasonable labor charges (as determined by manufacturer) if purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by manufacturer. The choice of remedy shall belong to manufacturer Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by manufacturer and for returning the goods to the dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the dealer to the designated factory. 3. Limitation Of Liability Manufacturer disclaims any express (except as set forth herein) and implied warranties with respect to the goods including, but not limited to, merchantability and fitness for a particular purpose Manufacturer makes no warranty as to the design, capability, capacity, or suitability for use of the goods Except as provided herein, manufacturer shall have no liability or responsibility to purchaser or any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused directly or indirectly by the goods including, but not limited to, any indirect, special, consequential, or incidental damages resulting from the use or operation of the goods or any breach of this warranty. Not withstanding the above limitations and warranties, manufacturer s liability hereunder for damages incurred by purchaser or others shall not exceed the price of the goods No action arising out of any claimed breach of this warranty or transactions under this warranty may be brought more than two (2) years after the cause of action has occurred. 4. Miscellaneous Proper venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe county, Texas Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall be deemed to be a waiver of any other term If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the invalidity of such provision shall not invalidate any other provisions herein Applicable law may provide rights and benefits to purchaser in addition to those provided herein. Keep for your records Attention: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine identification when applying for warranty. Alamo Industrial Implement Model Serial Number Date Purchased Dealer Attention: Read your operator s manual ALAMO INDUSTRIAL 1502 E. Walnut Seguin, Texas

119

120 1502 E. Walnut St. Seguin, Texas Sales and Marketing Tel Fax Warranty Registration/Claims Return Authorizations Online Part Orders Techical Information Tel Fax Interstater Flail Parts Manual (PUB 10-07) P/N P