Drive technology.....plastics

Transcription

1 dr ylin... Drive technology.....plastics

2 drive technology pplication examples CMER/LSER DJUSTMENT IN LBELING SYSTEM In a labeling system the camera and laser positioning are guided with two SHT/SLWE-XY -XY-table units. (Co. Pago Etikettiersysteme GmbH) POSITIONING OF MILLING HEDS luminium dust and chips cannot stick due to the absence of lubricants at any of the bearing points of the lead screw table SHT. (Berchtold GmbH) HEIGHT DJUSTMENT OF CODING DEVICE The lead screw unit gives variable and precise adjustment, free from any maintenance or lubrication. (Fiec Europe GmbH) PICK ND PLCE Quick and maintenance-free handling with toothed be axes (X, Y, Z axis). ELECTRIC CTUTOR lead screw table combined with an electric actuator for use in a variety of format adjustments. (Festo G & Co. KG) Lifetime calculation, configuration and more DJUSTMENT OF INSPECTION CMER ZLW toothed be axis in an inspection camera adjustment for checking the position of sealing rings. (OLPE Jena GmbH) WEB EDGE DETECTION The SLW lead screw unit with position indicator and hand wheel adjusts the sensors which detect the edge of the webbing and any print marks. 62 Online tools and more information Other exciting applications 63

3 drive technology Product overview drive technology SHT Linear SHT Standard: Preload: Flexible: The fast one with With ball bearing With quick release With quick release High temperature high helix thread: supported lead screw: mechanism: mechanism: up to +0 C: SHT SHT-PL SHTC SHTS SHT-BB SHTC-FF SHT-FF SHT-HTX Page 80 Page 81 Page 82 Page 83 Page 84 Page 86 Page 87 Page 88 Linear SHT Linear SLW Linear SLW Hygienic design: XY-tables: Compact: Preload: With ball bearing lead The fast one with high With protected Two units screw supports: helix thread: lead screw: are rolled into one: SHTC-HYD SHT-XY SLW SLWE-PL SLEW-BB SLWS SLW-PT SLWT Page 89 Page 90 Page 96 Page 97 Page 98 Page 99 Page 10 Page Linear SLW Linear SW Linear SW Linear module "light" SHTP... New New New Stainless steel version: XY-tables: XY-tables Dynamic high design: Direct drive short design: With motor available Small and low-cost: Light and strong: stainless steel version: from stock: SLW-ES SLW-XY SLW-XY-ES SW SWC DLE-S SHTP Mini SHTP Page 12 Page 14 Page Page 12 Page 12 Page 1212 Page 12 Page solid plastic Linear unit easytube Linear unit easytube Flat module New With quick release Single tube unit easytube with flange on easytube with carrier easytube with easytube "light": With ball bearing supported mechanism: easytube: both sides: flange on one side: measurement scale: lead screw based on SHTP-FF SET SET-F SETB SETM-SC SETC T: SLT-BB Page 1218 Page 1222 Page 1223 Page 1224 Page 1225 Page 1226 Page 1229 Miniature module Cantilever axis Cantilever axis Tooth Be xis ZLW New New New New Miniature module Miniature module Cantilever axis: Gripper axis: Lift/swivel unit: Standard Cost-effective Basic: Preload: toothed be axes: toothed be axes: SLN SLN-27 GRW GRQ HSQ ZLW ZLW-ECO Page 1233 Page 1234 Page 1238 Page 1239 Page 1240 Page 1243 Page Online tools and more information 3D-CD files, prices and delivery time 65

4 drive technology Product overview Tooth be axis ZLW E electric drive technology New Opposed toothed be Cantilever axis: Linear axes With motor available Pre-configured assembly Precise, efficient axes: with motor from stock: from stock: and compact: ZLW-OD ZW DLE-S robots lead screw motors Page 1252 Page 1254 Page 12 Page 1264 Page 1290 Page 1298 ccessories for drive technology ccessories for drive technology V-drive, V-drive Hygienic-Design Position indicator Lead screw clamp Hand wheels Flexshafts Stepper motors flexible positioning for heavy duty V-drive Page 16 Page 17 Page 17 Page 18 Page 19 Page 13 Page 13 Page 1314 ccessories for drive technology ccessories for drive technology New DC motor Protective cover Couplings Motor flanges Connecting cables Proximity switches: Spacer for height Mounting bracket with spur gear for DC motors for stepper motors Limit and reference adjustment: switches SLW/SHT module Page 1318 Page 1321 Page 1322 Page 1323 Page 1324 Page 1325 Page 1326 Page 1327 ccessories for drive technology ccessories for drive technology dapter kit T-grooved plate Slot nuts Clamps dapter plate Stainless steel for robot setup for mounting angle kit Page 1328 Page 1329 Page 13 Page 1331 Page 1332 Page Online tools and more information 3D-CD files, prices and delivery time 67

5 drive technology Linear drive technology Product overview The product portfolio provides lubrication-free drives that are driven either by a trapezoidal thread, high helix thread or toothed be. The user can choose a suitable individual solution from lightweight solid plastic units up to heavy duty stainless steel solutions. In all systems, the stroke length is freely selectable and the drive given either via hand wheel or motor. Linear with lead screw drive Polymer bearings and lead screw nuts give lubrication-free operation 3 shaft materials 8 trapezoidal thread pitches, 4 high helix thread pitches Body material made from stainless steel, aluminium, zinc or plastic Leadscrew machining to drawing or plain drive shaft (Steel, stainless steel- or aluminium lead screws) vailable accessories Standard min. 0 C max. + C HTX-Version min. 0 C Toothed be axes Deflection with grooved ball bearing Lubrication-free guide system with polymer plain bearings Various carriage lengths max. +0 C Polyurethane or neoprene toothed bes Hard-anodised aluminium profile When to use it? For format adjustments In extreme environments When a cost-effective, ready-to-fit solution is required When corrosion resistance is required For low noise When not to use it? For high loads combined with very high speeds When positioning accuracy <0.1 mm is necessary When high running performance is required in continuous operation When to use it? Fast positioning of small loads Quiet operation Flat design Underwater use with UW-be Cost-effective solution as basic version Long-term use Linear SHT Trapezoidal or high-helix lead screw drives Ball-bearing mounted lead screw units for higher dynamic forces Carriage in either quad or compact design Page 77 Linear SW Drive: Lead screw ball bearing Rail profile in high design Extremely torsion-resistant Page Linear SET easytube Corrosion resistant Low weight due to aluminium and plastic Simple, smooth design, protected lead screw Page 1219 Miniature SLN Based on N, low profile height Versions Basic, adjustable and preload Page 1231 Linear SLW Based on W Trapezoidal or high-helix lead screw drives Torsion-resistant dual shaft system Page 93 Linear module "light" SHTP Lightweight Cost-effective Corrosion resistant Page 1213 Linear SLT Variable pitch djustable T miniature carriage Lead screw arrangement can be selected either left or right Page 1227 Cantilever axis GRW Dynamic force transmission through rack ssembly option for limit and reference switch Page 1235 Standard 91) min. 0 C max. + C LT-Version min. - C max. + C 91) Does not apply to When not to use it? When high loads need to travel at highly dynamic forces When positioning accuracy < 0.1 mm is necessary Tooth be axis ZLW Versions Basic, Standard and Eco For fast positioning Ball bearings in deflection pulleys Page 1241 E electric drive technology Lubrication-free with motor Ready to install with motor, cable and initiator Drive: lead screw, toothed be or rack Page 1259 accessories ccessories for Position indicator, hand wheels, screw clamps, angle drives and so on Page Online tools and more information 3D-CD files, prices and delivery time online 69

6 drive technology drive technology Linear Lead screw slide mounted 121) Lead screw mounted with ball bearings Linear module Shaft Ø [mm] Thread Lead Screws Self locking head Carriages length [mm] Compatible with E SHT-08 8 Tr 06x , ZB 80 35/ Sg 6.35x ZB Tr x , ,400 1, PL 81 SHT Sg x12 - / ZB Sg x ZB 80 Tr 18x4 + 1,000 1,0 6, ,000 4,000 1, PL 81 SHT- Tr 18x8 + 36/1 + 1, , ,000 1, PL 81 Sg 18x0-1, , , SHT- Tr 24x5 + 50/ ,250 2,500, ,000 1,500 6,000 1,0 6.0 PL 81 SHTC Tr 26x ,500 4,000 16, SHTC Tr x ,500 6,250 25, M x SLW-06 5 Tr 08x + /0 +** , Sg 08x SLW-40 Tr x , ,400 1, TTF/PL 94 SLW-80 Sg x12-69/0/0/0 +** TTF/PL 94 SLW-1 Sg x TTF/PL 94 SLW Tr 14x4 + 0/0/ ,0 4, ,800 1, TTF/PL 94 Tr 18x4 + 1,000 1,0 6, ,000 4,000 1, TTF/PL 94 SLW-80 Tr 18x8 + 0/0/ , , ,000 1, TTF/PL 94 Sg 18x0-1, , ,0 0.0 TTF/PL 94 SLW-251 Tr 24x5 + 0/0/ ,250 2,500, ,000 1,500 6,000 1, SW-06 5 Tr 08x , /0 + 5 Sg 08x Tr x ,000 1, TTF/PL 12 SW-40 Sg x12-69/0/ TTF/PL 12 Sg x TTF/PL 12 Tr 12x ,000 1, TTF/PL 12 SW-80 Sg 12x , TTF/PL 12 Sg 12x TTF/PL 12 SW Tr 14x4 + 0/0/ ,000 1, TTF/PL 12 SLT Tr 08x , Sg 08x Tr 12x , SLT-04 Sg 12x , Sg 12x SLN M M5x Sg 5x SHTP M x SHTP-01- Tr 06x SHTP SHTP Tr x SET M M4x SET Tr x SET- Tr 12x Max. stroke length 1) [mm] Max. static, axial load capacity [N] Max. static, radial load capacity [N] Max. speed [rpm] Max. feed [m/min.] Max. stroke length 1) [mm] Max. stat. axial [N] Max. stat. radial [N] Max. speed [rpm] Max. feed [m/min.] Technical options (Pages 72+73) Page 1) When configuring your module, we ask that you note the igus specifications for maximum stroke lengths. The performance and load specifications shown above for all drive units are based exclusively on stroke lengths within the recommended values. Exceeding these can resu in undesirable effects to the function such as increased wear and noise. Be or lead screw contact cannot be excluded, and the rated performance and load specifications may not be attainable. 121) Linear on slide bearings require an aluminium shaft end support when connected to a motor The technical values in the specifications are maximum values for each criterion, e.g. speed, stroke length etc.; they are not cumulative values. Suitability under consideration of the individual parameters for usage can be checked online at module-finder. 70 Online tools and more information 3D-CD files, prices and delivery time online 71

7 drylin drive technology Technical options drylin drive technology Technical options In addition to the standard configurations, drylin -drives offer numerous solutions for the many requirements of different applications. Shaft materials djustable radial clearance The "turn to fit" feature allows individual clearance adjustment by hand. The adjustment is done in 0.01-mm increments and cannot be triggered unintentionally during the operation (SLW type series -). For lineal Types SLW and SW For lineal Type SHT When using axes of the SHT series, you can choose a shaft material from steel, stainless steel, or hard-anodised aluminium (standard). The short delivery time and excellent coefficients of friction and wear make the aluminium version the most common choice. Preload (PL) Lead screw materials The optional axial pretension reduces the backlash of the system. Positioning and repeatability can be optimised. The required drive torque increases only slightly. ll drylin can be delivered with self-locking trapezoidal steel and stainless steel lead screws; upon request, these can also be made from hard-anodised aluminium. The SHT and SLW series can also be configured with high-helix stainless steel lead screws. This allows for much higher pitches and drive speeds, but without the self-locking feature. For lineal Types SHT, SLW and SW Right-left and reverse In addition to the standard right-handed lead screws, lefthand thread lead screws and counter lead screws can also be used. This option often used in format adjustments can be specified for all diameters and types. lso available as a mui-carriage system or with right/left reverse travel. Bearing materials Online customer drawing Linear with ball-bearing mounted lead screw The SHT and SLW with ball bearing mounted leads crews give quiet operation, reduced vibration, and increased dynamic capability. These are also suitable for applications with motor drives. Zero-Backlash (ZB) Self-adjusting zero-backlash lead screw nuts are available for SHT in size 08 and 12. For movements that require repeatability and which are implemented through high helix thread, the ZB function provides a minimal lifelong backlash. Fast Forward (FF) SHT and SHTP plastic offer a combination of accurate positioning and fast manual adjustment. The bearing surfaces of the drylin drive units are equipped with lubrication and maintenance-free igus high performance polymers. Options include materials for high temperature application up to +0 C (iglidur X, type HTX), and also for FDcompliant environments (iglidur 180). Complete solutions made from stainless steel The use of and 1.41 makes of the guides resistant to seawater and chemical contact corrosion, and the guide shafts are also made from Linear with several carriages ll drylin can be configured with muiple carriages. The short carriages from the SHTC series are ideally suited for this. The second (or additional) carriage can be installed as a freely moving unit without lead screw, or as a fixed unit with its own trapezoidal lead screw. drylin SLW "Stop and Go" Linear with motor This additional function for carriages enables the use of an unlimited number of carriages on one guide controlled by only one lead screw. The connection to the lead screw is engaged or released via the button. Several drylin drive units are compatible with the drylin E modular kit. s axes, they can be easily and quickly configured directly to the matching igus stepper motors, power cables and initiators assembled and tested from one source. Online customer drawing drylin E compatible XY-Table The SHT and SLW can also be configured as XY cross-slide tables. XY adjustments can therefore be given with a single unit. 72 Online tools and more information 3D-CD files, prices and delivery time online 73

8 drive technology Design and calculation drive technology Design and calculation lead screw units have been developed for position settings of all types. The setting is achieved by means of trapezoidal lead screw that can be operated manually or by motor. The maximum continuous speed is 1.6 m/min according to thread and load. The suitability of the slide unit for an application can be checked using the graphs below. HORIZONTL The following trapezodial lead screw drive sizes are used in SHT, SLW and SET TR x 2: SHT-12, SHTC-12, SHTP-12, SLW-40, SLW-80, SLW-40-ES, SET-25 Tr 14 x 4: SLW-16 Tr 18 x 4: SHT-, SHTC-, SLW-80 Tr 24 x 5: SHT-, SHTC-, SLW-251 Tr 26 x 5: SHTC-40 Tr x 6: SHTC-50 VERTICL HORIZONTL VERTICL 1.8 Maximum feed [m/min.] 1.8 Maximum feed [m/min.] Rot. speed lead screw [rpm] Feed [m/min.] ,000 4,000 6,000 8,000,000 Centric loads in an horizontal installation position [N] Max. rotation speed [rpm] 0 2,000 4,000 6,000 8,000,000 12,000 12,000 Rot. speed lead screw [rpm] Feed [m/min.] ,000 1,500 2,000 2,500 Centric loads in a vertical installation position [N] Max. rotation speed [rpm] ,000 1,500 2,000 2,500 3,000 3,000 Centric loads in an horizontal installation position [N] Centric loads in a vertical installation position [N] Rred drive torque [Nm] 5 0 Max. drive torque [Nm] ,000 1,0 1,400 1,0 1,800 2,000 Required drive torque [Nm] 5 0 Max. drive torque [Nm] ,000 1,0 1,400 1,0 1,800 2,000 Centric loads in an horizontal installation position [N] Centric loads in a vertical installation position [N] 74 Online tools and more information 3D-CD files, prices and delivery time online 75

9 drive technology Product finder online Online configuration of systems Complete drive technology configurable with or without motor fter you have selected your application parameters, the product finder shows an overview of the lead screw and the motors that are suitable. The product finder calculates the price of the axis as well as the utilization rate of the motors and the service life in strokes. With just few clicks, you can put together a complete axis incl. motor, connecting cables and bui-on parts. general drive technology SHT Trapezoidal or high-helix lead screw drives Ball-bearing mounted lead screw units for higher dynamic forces Lead screws made from steel, stainless steel or aluminium Carriage in either quad block or compact design Lubrication and maintenance-free 76 Online tools and more information

10 SHT Linear dvantages Robust and precise Basic parts (shaft end supports/carriages) are made from machined aluminium with anodised surfaces Lubrication-free SHT SHT Linear Product overview 0% lubrication and maintenance-free Drive: self-locking trapezoidal thread or fast adjust high helix thread Bearing elements/ nut made from lubrication-free iglidur polymers Carriages in long or short "compact" design Shaft material: The SHT can be moved lubrication-free, while also offering high precision and robust components. The units can be individually configured with various shaft and lead screw materials, carriage lengths and additional functions. The SHT series is suitable for manual and motorised operation and is supplied ready for connection with E-motors. ll sliding surfaces are completely lubrication-free due to the use of iglidur high performance polymers Freely selectable stroke lengths High temperature version available SHT can be configured as a mui-carriage system or with right/left reverse travel Linear module SHT standard Solid design Three different sizes Various materials for shaft and lead screw Maintenance-free and optionally corrosion resistant Page 80 Linear module SHTC flexible Linear module SHT-PL "preload" Preloaded trapezoidal lead screw nuts, preload force: 50 N Manually and continuously adjustable radial clearance Low weight due to aluminium and plastic Page 81 Linear module SHTS the fast one luminium, steel or stainless steel Lead screw material: steel or stainless steel, plain or ball bearings Typical application areas Format adjustment ctuators Sensor adjustment Marking and engraving technology Laboratory equipment High flexibility due to short carriages Ideal for two carriages 5 sizes from Ø 12 up to 50 mm Page 82 With high helix lead screw High-Speed-solution for fast positioning Up to 0 mm travel/rotation Page 83 vailable in 3-8 days Detailed information about delivery time online. For manual adjustments, large range of accessories available Page 13 Block pricing online No minimum order value. From batch size 1. Linear module SHT-BB "ball-bearing supported" Linear module SHT-FF "fast-forward" drylin E compatible Configurable with motor as a ready to install drive ( E Page 1259) Carriage lengths: mm Pitch: 2 0 mm/rotation Stroke lengths: up to 1,500 mm Product finder Higher rotation speed and higher precision Be drive permits radial loads Constant drive torque Less axial clearance Page 84 With quick-release mechanism Precise and fast positioning Including self-locking brake Only recommended for horizontal applications Page 87 Special designs XY-Table High temperature version up to +0 C XY-tables standard and preload Hygienic design, light, washable From page 90 From page Online tools and more information 3D-CD files, prices and delivery time online 79

11 f SHT SHT Linear Product range Standard SHT Linear Product range Preload-Version SHT drylin E compatible Solid design Various materials for shaft and lead screw Maintenance-free and optionally corrosion resistant Trx2, Tr18x4, Tr24x5 Temperature resistant up to + C vailable accessories Page 13 Lead screw nuts are available separately Page 48 vailable with motor Page 1261 H tk ts complete Page 92 SHT-12-WM d T Shaft material Installation size Standard l + stroke l sg l2 drylin E compatible d Preloaded trapezoidal lead screw nut l + stroke l+hub complete Page 92 SHT-12-WM-PL Preload Shaft material Installation size Standard Preloaded trapezoidal lead screw nuts, preload force: 50 N Manually and continuously adjustable radial clearance Low weight due to aluminium and plastic Lead screw end unmachined Temperature resistant up to + C vailable accessories Page 13 Lead screw nuts are available separately Page 48 vailable with motor Page 1261 kt R f tg kq s sk ha l2 T ha sk tg kt l H sg tk ts Max. stroke length luminium shaft Steel shaft Max. static load capacity dditional dditional Weight Weight axial radial (per 0 mm) (per 0 mm) Max. stroke length luminium shaft Steel shaft Max. static load capacity dditional dditional Weight Weight axial radial (per 0 mm) (per 0 mm) [mm] [kg] [kg] [kg] [kg] [N] [N] [mm] [kg] [kg] [kg] [kg] [N] [N] SHT-12-WM SHT--WM SHT--WM ,800 1, ,0 6,400 1, ,500,000 SHT-12-WM-PL SHT--WM-PL SHT--WM-PL ,800 1, ,0 6,400 1, ,500,000 I H I R f tk ts ±0. ±0. ±0. SHT-12-WM SHT--WM SHT--WM tg kt s sk sg kq d T l2 ha ±0.1 Standard SHT-12-WM SHT--WM SHT--WM M M M Trx2 Tr18x4 Tr24x Trx2 92) 12h9 14h ) Lead screw end unmachined I H I R f tk ts ±0. ±0. ±0. SHT-12-WM-PL SHT--WM-PL SHT--WM-PL tg kt sk sg d T l2 ha ±0.1 Standard SHT-12-WM-PL SHT--WM-PL SHT--WM-PL M M M12 12 Trx2 Tr18x4 Tr24x Trx2 92) 12h9 14h ) Lead screw end unmachined 80 Online tools and more information 3D-CD files, prices and delivery time online 81

12 SHT SHT Linear Product range Flexible SHT Linear Product range The fast one with high helix thread SHT High flexibility Ideal for two carriages djustable vailable accessories Page 13 Lead screw nuts are available separately Page 48 vailable with motor Page 1261 complete Page 92 SHTC-12-WM l + stroke Shaft material Installation size Type: flexible Pitch Sgx12, Sgx50, Sg18x0 High-speed-solution vailable accessories Page 13 Lead screw nuts are available separately Page 48 vailable with motor Page 1261 complete Page 92 SHTS-12-WM-x12 Lead Shaft material Dimension High helix thread Standard l + stroke d l2 drylin E compatible T drylin E compatible Max. stroke luminium shaft Steel shaft Max. static load capacity length dditional dditional Weight Weight (per 0 mm) (per 0 mm) axial radial [mm] [kg] [kg] [kg] [kg] [N] [N] SHTC-12-WM SHTC--WM SHTC--WM SHTC-40-SWMH SHTC-50-SWMH 750 1,000 1,250 1,500 1, ,0 2,500 4,000 6,250 2,800 6,400,000 16,000 25,000 I H I R f tk ts tg ±0. ±0. SHTC-12-WM SHTC--WM SHTC--WM SHTC-40-SWMH SHTC-50-SWMH M M16 M16 M16 kt sk sg kq d T l2 ha ±0.1 Standard SHTC-12-WM SHTC--WM SHTC--WM SHTC-40-SWMH SHTC-50-SWMH M12 M16 M Trx2 Tr18x4 Tr24x5 Tr26x5 Trx Trx2 92) 12h9 14h9 16h9 h ) Lead screw end unmachined SHTS-12-WM-x12 SHTS-12-WM-x50 SHTS--WM-18x0 SHTS-12-WM-x12 SHTS-12-WM-x50 SHTS--WM-18x0 SHTS-12-WM-x12 SHTS-12-WM-x50 SHTS--WM-18x0 R Max. stroke length f H kt tk ts I H l R f tk ts tg tg ±0. ±0. ±0. kq luminium shaft M kt s sk sg kq d T l2 ha 92) Lead screw end unmachined ±0.1 Standard x12 Sgx12 92) x50 Sgx50 92) x h9 23 s sk sg l Max. static load capacity Weight dditional (per 0 mm) axial radial [mm] [kg] [kg] [N] [N] , ,0 ha 82 Online tools and more information 3D-CD files, prices and delivery time online 83

13 f SHT SHT Linear Product range With ball bearing lead screw supports SHT Linear Product range SHT Higher speeds Higher precision Less axial clearance Be drive permits radial loads Constant drive torque Zero-backlash function available for sizes 08 and 12 vailable accessories Page 13 Lead screw nuts are available separately Page 48 vailable with motor Page 1268 complete Page 92 SHT-BB-12-WM complete Page 92 tg s R SHT-08-ZB-WM Shaft material Installation size Ball bearing Standard kt tk ts d T kq sk l + stroke sg l l2 ha H drylin E compatible Shaft material Ball bearing, zerobacklash Installation size Standard SHTC-08-ZB SHT-08-ZB-WM-6X2P1 SHT-08-ZB-WM-6.35x12,7 SHT-12-ZB-WM-x12 SHT-BB-12-WM SHT-BB--WM SHT-BB--WM Max. stroke luminium shaft Steel shaft Max. static load bearing length dditional dditional capacity Weight Weight (per 0 mm) (per 0 mm) axial radial [mm] [kg] [kg] [kg] [kg] [N] [N] , ,000 4,000 1, ,500 6,000 I H I R f tk ts ±0. ±0. ±0. SHTC-08-ZB SHT-08-ZB-WM-6X2P1 SHT-08-ZB-WM-6.35x12,7 SHT-12-ZB-WM-x12 SHT-BB-12-WM SHT-BB--WM SHT-BB--WM tg kt s sk sg kq d T l2 ha ±0.1 Standard SHTC-08-ZB SHT-08-ZB-WM-6X2P1 SHT-08-ZB-WM-6.35x12,7 SHT-12-ZB-WM-x12 SHT-BB-12-WM SHT-BB--WM SHT-BB--WM M M M5 M5 M5 M / 6.35 Tr6x2 6.35x12.7 x12 Trx2 Tr18x4 Tr24x / 6.35 Tr6x2 92) ) x12 92) Trx2 92) 12h9 14h ) Lead screw end unmachined 84 Online tools and more information 3D-CD files, prices and delivery time online 85

14 SHT SHT Linear Product range With "Fast-Forward" quick release mechanism SHT Linear Product range With "Fast-Forward" quick release mechanism SHT Fast manual format adjustments Precise aluminium version Variable stroke length Mui-carriage solutions Only recommended for horizontal applications vailable accessories Page 13 vailable with motor Page 1261 Fast manual format adjustments luminium version For fast format adjustments Including self-locking brake Variable stroke length Only recommended for horizontal applications Max. stat. axial load 0 N (horizontal mounting position) Max. dynamic. axial load 50 N vailable accessories Page 13 vailable with motor Page Hub 85 complete Page 92 SHT-12-WM-FF l stroke + Hub 85 Fast Forward Shaft material Installation size Standard SHT Q SHT-01 drylin E compatible l + stroke drylin E compatible TRx2 70 TR-x2 36,5 TR-x2 36,5 TRx2 6,6 2 6,6 6,4 6, Max. stroke length luminium shaft Max. static load dditional capacity Weight (per 0 mm) radial 6 6,3 6 6, [mm] [kg] [kg] [N] SHTC-08-WM-FF SHT-12-WM-FF ,800 I H E4 l R l2 SHTC-08-WM-FF SHT-12-WM-FF f tk ts tg kt s 16 sk sg kg.5 d T 6 Trx2 92) ha ±0.1 Standard SHTC-08-WM-FF M SHT-12-WM-FF Trx ) Lead screw end unmachined press disengage move manually click into place fine-tuning 86 Online tools and more information 3D-CD files, prices and delivery time online 87

15 SHT SHT Linear Product range High temperature up to +0 C SHT Linear Product range Hygienic design SHT Shafts and lead screw made from stainless steel, bearings and nut iglidur X Carriages and shaft ends made from anodised aluminium Temperature resistant up to +0 C vailable accessories Page 13 complete Page 92 SHT--EWM-HTX High temperature Shaft material Dimension Standard l + stroke d T l2 Lightweight Washable Wide gaps Materials: plastic and V stainless steel Lead screw nuts made of FD-compliant iglidur 180 vailable accessories Page 13 complete Page 92 SHTC--EWM-HYD Hygienic Design Shaft material Dimension Type: flexible H I + stroke R f tk ts sg l kt tg kq s sk ha Max. stroke length Steel shaft dditional Weight (per 0 mm) Max. static load capacity axial radial SHT-12-EWM-HTX SHT--EWM-HTX [mm] [kg] [kg] [N] [N] ,800 1, ,0 6,400 The lead screw unit can be supplied completely with FD-compliant materials. I H I R f tk ts ±0. ±0. ±0. SHT-12-EWM-HTX SHT--EWM-HTX l H I R f It ts d T I2 ha ±0. ±0. SHTC--EWM-HYD Tr18x h9 23 tg kt s sk sg kq d T l2 ha ±0.1 Standard SHT-12-EWM-HTX SHT--EWM-HTX M Trx2 Tr18x4 26 Trx2 92) 12 h ) Lead screw end unmachined 7) In the event of severe temperature fluctuations during transport, storage and use, thermal expansion effects cannot be ruled out. 88 Online tools and more information 3D-CD files, prices and delivery time online 89

16 f f d T SHT SHT XY-tables Product range XY-table standard/preload SHT XY-tables SHT XY-table complete Page 91 SHT-XY-12-WM-PL-R SHT-XY-12-WM-PL-L-0-0-HR-ES Lead screw material blank: Steel C ES: Stainless steel 1.45 R: y-unit right (Standard with EWM) adjustment SHT SHT-PL L: y-unit left ccessories/options adjustment blank: Without extras (standard) Preload (optional) HK: Lead screw clamp (2x) L sg R Shaft material Dimension P: HR: Position indicator (2x) Hand wheel (2x) XY-table HTX: High temperature version up to Standard +180 C T d Z: Pins in TR x 2 90 x y Iy + stroke in mm left l2 Stroke y-direction vailable as standard and preload version Stroke x-direction High precision, extreme stiffness and accurate H alignment due to the single-piece carriage ha2 djustement y-unit djustments by trapezoidal thread ssembly of upper unit with left or right adjustment x-axis L: Lead screw end on the left side R: Lead screw end on the right side possible vailable accessories Page 13 ts tk Ix + stroke in mm right l1 d1 W Preload blank: Standard PL: Preloaded Max. stroke length [mm] H Base length Base length 0.3 ±0. ±0. lx ly kt R tg R f tk ts tg kt SHT-XY-08-WM SHT-XY-12-WM SHT-XY-12-WM-PL SHT-XY--EWM-PL 93) M y-axis ha1 Shaft material WM: Hard anodised aluminium SWM: Cf53 (1.1213) EWM: Stainless steel X5 (1.4125) Dimensions 12: Size ø 12 mm : Size ø mm Type XY-Table sg d T l1 d1 d1 l2 ha1 ha2 W SHT-XY-08-WM SHT-XY-12-WM SHT-XY-12-WM-PL SHT-XY--EWM-PL 93) Standard ernative Standard ernative ha2 ha1 M5 8 Tr6x2/Tr6.35x Trx2 Trx2 6 h9 Trx2 6 h Trx2 Trx2 6 h9 Trx2 6 h TR18x4 26 TR18x4 12 h h Required accessories (e.g. hand wheel) can be ordered left- or right-mounted in the y-direction. Order example for SHT-XY-12-WM-L-0-0-HR, left adjustment, stroke 0/0 mm, 2 hand wheels 93) For size we recommend stainless steel shafts (EWM), WM also available 90 Online tools and more information 3D-CD files, prices and delivery time online 91

17 SHT SHT Linear for a complete system SHT-12-WM-0-HR-ES Lead screw material blank: Steel C (standard) ES: Stainless steel 1.45 (standard with EWM) L: nodised aluminium Options blank: Without extras (standard) HK: Lead screw clamp P: Position indicator HR: Hand wheel PL: Preloaded HTX: High temperature version up to +180 C HYD: Hygienic Design Z: Pins in TR x 2 FF: Fast Forward ZB: Zero-Backlash Stroke length in mm Shaft material WM: Hard anodised aluminium SWM: Cf53 (1.1213) EWM: Stainless steel X5 (1.4125) Dimensions 12: Size ø 12 mm (SHT, SHTC, SHTS) : Size ø mm (SHT, SHTC, SHTS) : Size ø mm (SHT, SHTC) 40: Baugröße ø 40 mm (SHTC) 50: Baugröße ø 50 mm (SHTC) Type SHT: Standard SHT-PL: Preload SHTC: Flexible SHT-BB: With ball-bearing mounted lead screw SHTS: With high helix lead screw SHT-XY: XY-table general drive technology SLW Lubrication-free based on W guides Trapezoidal or high-helix lead screw drives Torsion-resistant dual shaft system delivery time with alu shaft WMP: 2-3 days, with stainless steel shafts EWM or steel shaft SWM: 3-8 days Many carriage and rail options Suitable for manual and motor-operated adjustments 92 Online tools and more information

18 SLW Linear dvantages Modular design Shaft end supports are made from anodised aluminium or from chromated die-cast zinc Lead screw mounted with plain or ball bearings W guide system Lubrication and maintenancefree lead screw nuts Mounting plates made from anodised aluminium Lubrication-free SLW Extremely torsion resistant aluminium dual shaft rails and many carriage versions characterise the W product range, and form a well rounded modular kit for the SLW drives. The are very low profile, as well as robust. The SLW stages are ideal for manual adjustments, but also can be fitted with a motor to make an electrical actuator. Variable carriage widths and lengths Flat guide rails or high profile Corrosion resistant made from stainless steel available SLW Linear Product overview Flat and torsionally stable Linear module SLW compact Linear module SHT-PL "preload" High torsional stability, fully supported Lubrication-free and precise Cost-effective Preloaded trapezoidal nut (preload force: 50 N) Shaft end supports made according to installation size Manually adjustable radial clearance, reduction of the of chromated zinc, anodised aluminium or plastic axial clearance Page 96 Page 97 Fully configured carriages with four W individual bearing housings with lubrication-free liners Typical application areas Format and lane adjustments Packaging technology Height adjustments 3D printers Camera adjustment Linear module SHT-BB "ball-bearing supported" Efficient and dynamic Linear module SLWS with lead screw Fast positioning High-helix lead screw drives Lead screw material: steel or stainless steel vailable in 3-8 days Quiet, reduced clearance Up to 1,500 rpm (according to length and load) Up to 0 mm stroke per rotation Page 99 Detailed information about delivery time online. Page 98 Drive: self-locking trapezoidal thread or fast adjust high helix thread Block pricing online No minimum order value. From batch size 1. For manual adjustments, large range of accessories available Page 13 Carriage lengths: -250 mm Carriage widths: mm Stroke lengths: up to 1,250 mm drylin E compatible Configurable with motor as a ready to install drive Product finder Linear module SLW stainless steel version With corrosion resistant steel components Linear module special designs SLW with protect mechanism for applications ( E Page 1259) Choice of bearing material: iglidur J (standard), with high levels of dirt iglidur 180 (FD-compliant), iglidur X High flexibility through SLWT with dual lead screw (high temperature up to +0 C) XY-table solutions For environments involving contact with water and Page chemicals Page Online tools and more information 3D-CD files, prices and delivery time online 95

19 SLW SLW Linear Product range Compact SLW Linear Product range Preload Version SLW Flat and compact High torsional stability Fully supported luminium W guide rails, complete Page 16 SLW-40 Radial and axial pre-load Manual adjustable clearance High torsional stability Fully supported complete Page 16 SLWE-40-PL hard anodised luminium W guide rails, vailable accessories Dimension hard anodised Preload Page 13 Compact vailable accessories Dimension Lead screw nuts are available Page 13 djustable clearance separately Page 48 T Lead screw nuts are available Compact vailable with motor d separately Page 48 Page 1261 vailable with motor lb lb Page 1261 drylin E compatible drylin E compatible l + stroke and dimensions [mm] Design Max. stroke Shaft weight dditional Max. static load capacity End block length (per 0 mm) axial radial material l + l stroke [mm] [kg] [kg] [N] [N] SLW-06 SLW-40 SLW-80 SLW-1 SLW-16 SLW-80 SLW ,000 1, ,0 1,0 2, ,800 2,800 2,800 4,0 6,400,000 Plastic Zinc die-casting luminium luminium luminium luminium luminium I 94) H l hw f Ib tk ts tg ±0. ±0. ±0. SLW-06 SLW-40 SLW-80 SLW-1 SLW-16 SLW-80 SLW M M M16 kt s sk sg kq d T l2 ha ±0.1 Standard SLW-06 SLW-40 SLW-80 SLW-1 SLW-16 SLW-80 SLW M4 M Trx2 Trx2 Trx2 Tr14x4 Tr18x4 Tr24x Trx2 92) Trx2 92) Trx2 92) Tr14x4 92) 12h9 14h lb lb See SLW on left side I 94) H l hw f Ib tk ts ±0. ±0. ±0. SLWE-40-PL SLWE-80-PL SLWE-16-PL SLWE-80-PL tg kt s sk sg kq d T l2 ha ±0.1 Standard SLWE-40-PL SLWE-80-PL SLWE-16-PL SLWE-80-PL M M Trx2 Trx2 Tr14x4 Tr18x4 26 Trx2 92) Trx2 92) Tr14x4 92) 12h ) Lead screw end unmachined; 94) Carriages also in 0, 0, 0 and 250 mm lengths available on request 92) Lead screw end unmachined; 94) Carriages also in 0, 0, 0 and 250 mm lengths available on request 96 Online tools and more information 3D-CD files, prices and delivery time online 97

20 SLW SLW Linear Product range With ball bearing lead screw supports SLW Linear Product range Compact with high helix thread SLW Lower drive force Pitch 08x, x12, x50, 18x0 Optimised clearance complete Page 16 High torsional stability complete Page 16 Up to 1,500 rpm (according to length and load) SLWE-BB-40 luminium W guide rails, hard anodised SLWS-06-08x luminium W guide rails, hard anodised Quiet operation reduced vibration of the overall system Ball bearings in both shaft end Dimension Ball bearing djustable Compact BB-version with ball bearings lead screw supports available vailable accessories Page 13 Lead screw nuts are available separately Page 48 Lead Dimension High helix thread Compact supports vailable accessories Page 13 drylin E compatible Lead screw nuts are available separately Page 48 vailable with motor Page 1261 lb lb l + l stroke stroke and dimensions [mm] l + stroke Design 96) Max. stroke Weight dditional Max. static load capacity Max. rotation Max. feed length (per 0 mm) axial radial speed rate [mm] [kg] [kg] [N] [N] [1/min] [m/min] SLW-BB-06 SLWE-BB-40 SLWE-BB-80 SLWE-BB-16 SLWE-BB , ,000 2,000 2,800 5,000 1,000 1,500 1,500 1,500 1, I H l hw f lb tk ts tg ±0. ±0. ±0. SLW-BB-06 SLWE-BB-40 SLWE-BB-80 SLWE-BB-16 SLWE-BB M M kt sk sg kq s d T l2 ±0.1 Standard on request SLW-BB-06 SLWE-BB-40 SLWE-BB-80 SLWE-BB-16 SLWE-BB M Tr8x Trx2 Trx2 Tr14x4 Tr18x4 26 Tr08x Trx2 Trx2 Tr14x4 12 h9 6 h9 6 h9 8 h ) Optional machined lead screw end 96) Double rails, square Page 864, round Page ) ha Design 96) Max. stroke Weight dditional Max. static load capacity length (per 0 mm) axial radial [kg] [kg] [N] [N] SLWS-06-08X SLWS-40-X12 SLWS-40-X50 SLWS-80-X12 SLWS-80-X50 SLWS-80-18X ,0 I H l hw f Ib tk ts tg ±0. ±0. ±0. SLWS-06-08X SLWS-40-X12 SLWS-40-X50 SLWS-80-X12 SLWS-80-X SLWS-80-18X M kt s sk sg kq d T l2 ha ±0.1 SLWS-06-08X SLWS-40-X12 SLWS-40-X50 SLWS-80-X12 SLWS-80-X50 SLWS-80-18X M Sg08x Sgx12 Sgx50 Sgx12 Sgx50 Sg18x0 38 Sg8x 92) Sgx12 92) Sgx50 92) Sgx12 92) Sgx50 92) 14h ) Lead screw end unmachined 96) Double rails, square Page 864, round Page Online tools and more information 3D-CD files, prices and delivery time online 99

21 f f SLW SLW Linear Product range With protected lead screw SLW Linear Product range Two units are rolled into one SLW W profile rail as a protective Carriages can be controlled mechanism complete Page 16 separately complete Page 16 vailable with pitches x2, x12,x50 SLW-BB-PT-40 Different lead screw pitches can be applied SLWT-80 Low profile design vailable with motor Page 1261 Dimension Protect Ball bearing Compact Separate manual adjustment of carriages High flexibility Clearance adjustment (optional) Dimension Double unit Compact drylin E compatible l2 hw s tk ts tk kt l2 s hw ts kt ha d l + l + Hub stroke tg ha kq sg tg sk T lb lb lb l d l lb H T l l + l + stroke Hub Max. stroke length Weight dditional (per 0 mm) Max. static load capacity axial radial 97) End block material Max. stroke length Weight dditional Max. static load capacity End block (per 0 mm) axial radial material [mm] [kg] [kg] [N] [N] [mm] [kg] [kg] [N] [N] SLW-PT ,000 luminium SLWT ,000 luminium SLW-BB-PT ,000 luminium I H / l hw f Ib tk ts tg ±0. ±0. SLW-PT SLW-BB-PT kt d T l2 98) ha ±0.1 SLW-PT-40 SLW-BB-PT Trx2 Trx2 Trx2 Trx2 6 h9 6 h I H l hw f Ib tk ts ±0. ±0. ±0. ±0.1 SLWT tg kt sk s sg kq d T l2 ha ±0.1 Standard ernative SLWT Trx2 92) Trx2 6 h ) Lead screw end unmachined 97) Depends on load and rotation speed 98) Thread/remaining thread visible 10 Online tools and more information 3D-CD files, prices and delivery time online

22 SLW SLW Linear Product range Made of stainless steel My sketches SLW Stainless steel version with corrosion resistant steel components (1.45, or ) Choice of bearing material: iglidur J: Standard iglidur 180: FD-compliant iglidur X: High temperature up to +0 C 7) vailable accessories Page 13 complete Page 16 SLW-ESJ-40 Dimension Bearing material iglidur J Stainless steel Compact d T l + stroke Shafts-Ø Max. Weight dditional Max. static stroke length (per 0 mm) load capacity [mm] [mm] [kg] [kg] axial [N] radial [N] SLW-ESJ-40 SLW-ESX-40 SLW-ES SLW-ESJ-80 SLW-ES , , ,800 1, ,0 6,400 1, ,0 6,400 I H l hw f Ib tk ts tg SLW-ES-40 SLW-ES ±0. ±0. ± M kt s sk sg kq d T l2 ha SLW-ES-40 SLW-ES-80 ±0.1 Standard Trx2 Trx2 92) Tr18x h ) Lead screw end unmachined 7) In the event of severe temperature fluctuations during transport, storage and use, thermal expansion effects cannot be ruled out 12 Online tools and more information 3D-CD files, prices and delivery time online 13

23 SLW SLW XY-tables Product range Compact XY-tables for manual adjustments SLW XY-tables Product range XY-tables stainless steel version SLW complete Page 16 SLW-XY-40-PL For manual adjustments High torsional stability Structure entirely made from V and V4 stainless SLW-XY-06 SLW-XY-40 Preload (optional with steel materials Chemical and corrosion resistant sizes 40 and 80) vailable accessories Page 13 Dimension luminium W guide rails, hard anodised XY-table Compact ly + Stroke in mm Preload version SLWE-XY-PL left also available (optional, sizes: 40/80) vailable accessories Page 13 SLW-XY-80 ly + Stroke in mm left lb lb L R lx + Stroke in mm right L R lx + Stroke in mm right I x x y y I Max. stroke l H Base Base f Ib tk ts tg kt Max. stroke l H Base Base f Ib tk ts tg kt length length length length length length [mm] 0.3 ±0. ±0. lx ly [mm] 0.3 ±0. ±0. lx ly ±0.1 SLW-XY SLW-XY-ESJ SLW-XY SLW-XY sg d T l1 d1 d1 l2 ha1 ha2 W Standard ernative Standard ernative ha2 ha1 SLW-XY-06 M SLW-XY-40 SLW-XY-80 Trx2 Trx2 Trx2 Trx2 6 h9 6 h9 Trx2 Trx2 6 h9 6 h The hand wheel can be ordered left- or right-mounted in the y-direction. Left: SLW-XY-40-L-0-0 for 0 mm stroke length on the x-axis and 0 mm on the y-axis Right: SLW-XY-40-R-0-0 for 0 mm stroke length on the x-axis and 0 mm on the y-axis sg d T l1 d1 d1 l2 ha1 ha2 W Standard ernative Standard ernative ha2 ha1 SLW-XY-ESJ-40 Trx2 Trx2 6 h9 Trx2 6 h The hand wheel can be ordered left- or right-mounted in the y-direction. Left: SLW-XY-ESJ-40-L-0-0 for 0 mm stroke length on the x-axis and 0 mm on the y-axis Right: SLW-XY-ESJ-40-R-0-0 for 0 mm stroke length on the x-axis and 0 mm on the y-axis 14 Online tools and more information 3D-CD files, prices and delivery time online

24 SLW SLW Linear complete system: SLW-40-0-HR-ES Lead screw material blank: Steel C (standard) ES: Stainless steel 1.45 L: nodised aluminium dditional options blank: Without extras (standard) HK: Lead screw clamp P: Position indicator HR: Hand wheel PL: Preloaded Z: Pins in TR x 2 (optional) WT: V-drive Stroke length in mm Dimensions 06: Shaft ø 6 mm, width mm (SLW, SLWS) 40: Shaft ø mm, width 40 mm (SLW, SLWE) 80: Shaft ø mm, width 80 mm (SLW, SLWE) 16: Shaft ø 16 mm, width mm (SLW, SLWE) 80: Shaft ø mm, width 80 mm (SLW, SLWE) 251: Shaft ø 25 mm, width 1 mm (SLW) Type SLW: Standard SLWE-PL: With preload SLWE-BB: Leadscrew drive with ball-bearing SLWS: With high helix lead screw SW: High design SLW-ES: Stainless steel version SLW-XY: XY-tables general drive technology SW Lubrication-free based on W guides Trapezoidal or high-helix lead screw drives Robust design Ready-to-install stepper or DC motors Dynamic ball bearing 16 Online tools and more information

25 SW Linear dvantages Compact high design Shaft end support made from black anodised aluminium Lubrication-free SW SW Linear Product overview Dynamic ball bearing SW Leadscrew drive with ball-bearing as Standard Extremely torsion-resistant W high profile made from hard anodised aluminium Lubrication and maintenancefree lead screw nuts The W high profile provides the torsionresistant base for the axes of the SW series. Thanks to the ball-bearing lead screw and high-profile design, the SW are perfectly suitable for the direct connection to stepper or DC motors. Slots in profile sections enable initiators to be freely positioned and, at the same time, enable set-up as a mui-axis robot by means of suitable adapter plates. Optimised unit for motor connection W high profile with variable mounting options using clamping elements / slot nuts For manual or electrical adjustments Ideal for single and/or mui-axial constructions Linear module SW Robust high design in 4 sizes Trapezoidal or high-helix lead screw drives For manual positioning or motorised operation Page 12 Linear module SWC Compact short design With integrated E lead screw motor Optimised ratio of useful length to total length Page 12 The carriages consists of four W bearing housings equipped with lubrication-free liners Typical application areas Positioning functions 3D scanner Format adjustments Linear robot structures Height adjustments Linear module DLE Configured with NEM stepper motors vailable in 24 hours Pre-assembled and tested Page 1212 Linear module SW-P Dynamic module with W carbon profile Extremely lightweight and robust Stroke lengths up to 0 mm Page 50 ssembly plates made from anodised aluminium, vailable in 3-8 days available in different lengths Detailed information about delivery time online. Block pricing online No minimum order value. From batch size 1. dapter plates for robot solutions available Lead screw material: Carriage lengths: -250 mm Carriage widths: 54-7 mm Stroke lengths: up to 750 mm steel/stainless steel/aluminium Product finder Drive: self-locking trapezoidal thread or fast adjust high helix thread drylin E compatible Configurable with motor as a ready to install drive ( E Page 1259) 18 Online tools and more information 3D-CD files, prices and delivery time online 19

26 hw f ha ha H kq kq E5 hm H kt kt hw t d T d SW SW Linear Product range Dynamic in high design SWC Linear Product range Direct drive in short design SW Trapezoidal or high helix threads Ball bearing leadscrew supports Rail profile in high design, extremely torsion-resistant luminium W guide rails, hard anodised High stability Cost-effective and 0% lubrication-free vailable accessories Page 13 Lead screw nuts are available separately Page 48 Smaller installation space and more stroke Compact short design due to the use of E lead screw motors Optimised ratio of useful length to total length (compared to the SW series, up to 70 mm) Improved operating characteristics Space saving and low weight vailable accessories Page 13 lb l lb l drylin E compatible E6 tk ts l l + stroke Hub lc + Hub stroke - ( 1 : 1,5 ) l2 lc + stroke Hub tk ts tg f sg sk Max. stroke length Weight dditional Max. speed Max. static load capacity [mm] [kg] (per 0 mm) [U/min.] axial [N] radial [N] SW-06 SW-40 SW-80 SW ,000 1,500 1,500 1, ,000 2,000 3,000 I H E5 E6 l lc hw f lb SW / / / SW /0/ /87/ /1/ SW SW l sg sk l l + stroke Hub Max. stroke length Weight dditional Max. speed Max. static load capacity [mm] [kg] (per 0 mm) [U/min.] axial [N] radial [N] SWC-06 SWC ,000 1, ,000 I H l lc hw f lb SWC SWC tg tk ts tg kt sk sg kq d T l2 ha tk ts tg kt sk sg kq d T l2 ha ±0.1 Ø ±0.1 Ø SW Tr8x Tr8x 2 Tr08x SWC M5 7 M4 2 5 SW Trx2 Trx2 Ø6 h9 3) 35.5 Sg08x SW Tr12x3 Tr12x3 Ø8 h9 3) 37.5 Trx2 92) SWC SW M Tr14x4 Tr14x4 Ø8 h9 3) 59.0 Sgx ) Lead screw end unmachined, also available with machined end 92) Lead screw end unmachined 12 Online tools and more information 3D-CD files, prices and delivery time online 12

27 hw ha H kq E5 kt T d SW DLE Linear Product range Linear with motor deliverable within 24 hours from stock with motor vailable from stock Ready-to-install and pre-assembled NEM stepper motors with stranded wires vailable accessories Page 13 lb l lb l l + stroke Hub E6 tk ts lc + stroke Hub - ( 1 : 1,5 ) l2 tg f sg sk l Installation size Length of Stroke length Motor type Max. static load capacity carriage axial [N] radial [N] DLE-S-0004 DLE-S-0005 DLE-S-0006 SW-06 Tr08x SW-40 Trx2 SW-80 Tr12x NEM stranded wires NEM23 stranded wires NEM23XL stranded wires ,000 2,000 general drive technology SHTP Lubrication-free polymer Drive: trapezoidal thread Lightweight Corrosion resistant Ideal for mui-carriage solutions 1212 Online tools and more information

28 f SHTP Linear "light" dvantages Light and cost-effective Shaft end blocks from corrosion resistant, robust plastic Drive: self-locking trapezoidal thread or fast adjust high helix thread Plastic guide carriages are available with threads integrated into the housing, also with completely lubrication-free R liners and trapezoidal lead screw nuts Shaft material: aluminium, steel or stainless steel Lubrication-free SHTP The SHTP series is characterised by the weight reducing use of solid plastic components as shaft end supports and carriages. ll 3 installation sizes move without lubrication and are configurable with corrosion free materials. This cost-effective aernative with muiple optional accessories is suited for manual adjustment tasks, such as sensor adjustments. Very light, flat design Ideal for mui-carriage solutions Low-cost aernative to home-made solutions Typical application areas Gripper technology Format adjustments Camera adjustment vailable in 3-8 days Detailed information about delivery time online. SHTP Linear Product range Small and cost-effective solid plastic Miniature version Lightweight Very low price Corrosion resistant Carriages and shaft end supports made from high-performance polymers vailable accessories Page 13 SHTP WM H Ht kt l2 d l Shaft material Dimension Design Type SHT-Polymer s T SHTP ts tk ha Lead screw material: steel or stainless steel For manual adjustment Extensive accessories available Block pricing online No minimum order value. From batch size 1. Carriage lengths: mm Stroke lengths: up to 500 mm Product finder SHTP WM R I + stroke Max. stroke luminium shaft Max. static load capacity More Information length Weight dditional [kg] axial radial [mm] [kg] (per 0 mm) [N] [N] Carriage, square, with 4 symmetrical mounting holes Page 13 I H Ht l R f kt tk ts SHTP WM s d T l2 99) ha SHTP WM ) Lead screw end unmachined (standard) 1214 Online tools and more information 3D-CD files, prices and delivery time online 12

29 SHTP SHTP Linear Product range Light and robust plastic and aluminium SHTP Linear Product range Economical solid plastic SHTP Lightweight Low-profile design Ideal for mui-carriage solutions vailable accessories Page 13 SHTP-01- Dimension Design Type SHT-Polymer Solid polymer design Lightweight Cost-effective Corrosion resistant vailable accessories Page 13 vailable with motor Page 1261 SHTP WM Shaft material Dimension Design Type SHT-Polymer I + stroke l ts ts T D-D T l2 l2 D D D D d d Øs sg I + stroke l+hub tk tk T ha f Max. stroke length luminium shaft Weight dditional [kg] More Information Max. stroke length luminium shaft Weight dditional [kg] More Information [mm] [kg] (per 0 mm) [mm] [kg] (per 0 mm) SHTP Liners and lead screw nuts made from iglidur J SHTP SHTP Liners and lead screw nuts made from iglidur J Bearing and nut integrated into the carriage I H l R f tk ts ± SHTP s sg d T l2 99) ha Max. static load capacity axial radial [N] [N] SHTP M5 Tr08x Tr08x ) Lead screw end unmachined (standard) I H l R f tk ts ± SHTP SHTP s sg d T l2 99) ha Max. static load capacity axial radial [N] [N] SHTP SHTP Trx2 Trx2 Trx2 Trx ) Lead screw end unmachined (standard) 1216 Online tools and more information 3D-CD files, prices and delivery time online 12

30 SHTP SHTP Linear Product range With "Fast-Forward" quick release mechanism Light solid polymer model For fast format adjustments Self-locking Variable stroke length Only recommended for horizontal applications Max. stat. axial load 0 N Max. dynamic. axial load 50 N vailable accessories Page 13 SHTP WM-FF Fast Forward Shaft material Dimension Design Type SHT-Polymer 55 ø 6,6 TR x ø 12 TR x 2 42, stroke + Hub Max. stroke length Weight dditional weight [mm] [kg] (per 0 mm) SHTP WM-FF 0) ) Liners and trapezoidal lead screw nut made from iglidur J 85 general drive technology SET Lubrication-free single-tube adjustment Drive: trapezoidal thread Simple, smooth design Lightweight due to aluminium and plastic Temperature resistance up to +50 C press > disengage > move manually > click into place > fine-tuning 1218 Online tools and more information

31 SET easytube dvantages Single-tube adjustment Shaft end blocks made from robust plastic, also available as a flanged version Lubrication-free unit "easytube" SET easytube Product overview Efficient design with protected lead screw and variable mounting Guide tube made from anodised aluminium Carriages, trapezoidal lead screw nuts and torque support made from lubrication-free plain bearing polymers Trapezoidal lead screw (inside) made from steel or stainless steel The unit for easy adjustment functions is characterised by a simple but effective and solid design. complete system is bui up from few components. The outer anodised aluminium tube guides the carriage/s and at the same time protects the trapezoidal lead screw and lead screw nut from external influences. Carriage, torque support and trapezoidal lead screw nut in one component and are made from a special plain bearing highperformance polymer. This guarantees freedom from lubrication with simuaneously low coefficient of friction and optimal wear rates. The iglidur bearing materials are also used in the axial bearings of the lead screw. Protected lead screw Effective design vailable with measurement scale without lead screw Flanged version for axial mounting easytube single tube unit For light format adjustments Protected lead screw, torque-resistant Trapezoidal or high-helix lead screw drives Page 1222 easytube with carrier flange on one side For horizontal and vertical installation Massive aluminium carrier flange on one side Space saving structure Page 1224 easytube with flange, on both sides For axial mounting Simple, smooth design Page 1223 easytube with measurement scale With lasered, wash-proof scale Carriage with clamp vailable with/without lead screw Page 1225 Guide tube available with measurement scale Typical application areas Sensor and camera positioning Format adjustment vailable in 3-8 days Stainless steel clamping rings, Detailed information about delivery time online. journal and axial bearings made from plain bearing polymers Block pricing online No minimum order value. From batch size 1. Carriage lengths: -55 mm Stroke lengths: up to 850 mm easytube "light" Weight-optimised carriage Compact structure ccessories for Position indicator, hand wheels, screw clamps, angle drives and so on Product finder lso in flange version available Page 1226 From page 13 Large range of accessories available Page Online tools and more information 3D-CD files, prices and delivery time online

32 SET easytube SET easytube Product range easytube SET easytube Product range With flange SET easytube E4 sb H h1 SET-25-WM l2 SET-25-WM-F Shaft material With flange Dimension Shaft material easytube Dimension h easytube l l + I + Hub stroke s s H E5 ts h For simple adjustments Trapezoidal lead screw inside I + stroke l2 Flanged version for axial mounting Simple, smooth design ts l 2 Corrosion-free with stainless steel lead screw vailable accessories Page 13 Low weight due to aluminium and plastic Temperature resistant up to + C vailable accessories Page 13 Max. stroke luminium shaft Max. static load capacity Max. stroke luminium shaft Max. static load capacity length Weight shaft end supports and carriage dditional (per 0 mm) axial radial length Weight shaft end supports and carriage dditional (per 0 mm) axial radial [mm] [kg] [kg] [N] [N] [mm] [kg] [kg] [N] [N] SET-12-WM SET-25-WM-F SET-25-WM SET--WM-F SET--WM l H E4 l h h1 ts s sb l2 92) SET-12-WM SET-25-WM SET--WM M4 M4 M4 Trx2 Tr12x3 I 2 H E5 l h ts s l2 92) SET-25-WM-F SET--WM-F Trx2 Tr12x3 92) Lead screw end unmachined 92) Lead screw end unmachined 1222 Online tools and more information 3D-CD files, prices and delivery time online

33 SET easytube SET easytube Product range Preloaded on one side SET easytube Product range With measurement scale SET easytube SETB-25-WM SETM-25-WM-0-SC Shaft material Scaling Dimension Stroke length easytube Shaft material Dimension Manual V Ø d3 l h Ø 1 without lead screw (optional) easytube SW L1 I + l + stroke Hub l2 Ø s2 Ø s1 Horizontal and vertical installation at one end Ideal for the positioning of sensors and cameras in format adjustments Easy assembly Flexible installation Space saving Protected lead screw Lasered scale Corrosion resistant Continuously clamped vailable with/without lead screw 3 stroke lengths available from stock F radial [N] 0 Max. extension at maximum load [mm] 66 Max. extension at nominal load 0 N [mm] 0 Max. drive force without load [N] Max. holding strength [N] 0 Max. stroke length [mm] 0 Max. stroke length Max. static load capacity axial radial at arm 128) [mm] [N] [N] SETB-25-WM l h V L1 l2 92) d3 l s1 s2 SW Part no. measurement scale Part no. measurement scale without lead screw with trapezoidal lead screw x2 SETM-25-WM-0-SC SET-25-WM-0-SC SETM-25-WM-400-SC SET-25-WM-400-SC SETM-25-WM-0-SC SET-25-WM-0-SC More dimensions see SET Page 97 Stroke length [mm] SETB-25-WM Trx ) Lead screw end unmachined More dimensions on request 128) The supporting torque at the clamping flange must not exceed Nm 1224 Online tools and more information 3D-CD files, prices and delivery time online

34 SET easytube SET easytube Product range Weight-optimised carriage option SETC-25-WM Shaft material Dimension easytube E4 sb H h1 l2 I + stroke l + Hub Øts Øs Weight-optimised For cost-sensitive adjusting movements Simplified solid assembly Light, clean and low noise l Weight Max. stroke length Max. static load capacity axial radial SETC-25-WM SETC-25-WM 92) Lead screw end unmachined More dimensions on request [kg] [mm] [N] [N] I H E4 I h1 ts s sb l2 92) M4 Trx2 general drive technology SLT Based on lubrication-free T miniature guide system Trapezoidal or high-helix lead screw drives Flat and compact design Carriages with individually adjustable clearance Variable lead screw arrangement 1226 Online tools and more information

35 T d d T ha H kt SLT Linear dvantages Flat, lightweight and lubrication-free Shaft end supports/carriages made of anodised aluminium Lead screw mounted with ball bearings Lead screw arrangement left or right of the carriage Self-locking trapezoidal thread or fast adjustment with high helix thread T miniature carriage with individual clearance adjustment Lubrication-free SLT n extremely flat structure, the lateral lead screw arrangement, a striking design, are just some of the reasons why the module SLT was honoured with the 14 IF ward. Technically, the system is impressive with ball-bearing supported trapezoidal thread or high helix thread lead screws for motorised or manual operation. The basis of the SLT series is the T low profile guide system in sizes 12 and. Low profile structure through lateral lead screw arrangement Lubrication-free, corrosion-resistant, lightweight Variable pitch djustable T miniature carriage Lead screw arrangement can be selected either left or right SLT Linear Product range With ball bearing lead screw supports SLT-BB-0412-ER-S00RG-xxx tk Stroke length in mm Lead screw end G: Threaded end Thread R: Right Pitch Lead screw SLT Steel or stainless steel lignment lead screw R: Right (standard) L: Left djustable carriage TWE Installation size Design Type BB: with Ball Bearings Lead screws of steel or stainless steel Typical application areas Format adjustments Laboratory and medical technology Optical equipment as sg tg lb lb f l l2 Hard anodised T miniature rails vailable in 3-8 days Detailed information about delivery time online. l l2 sg lb lb l + stroke l + Hub l + l stroke + Hub Hand wheel, position indicator, and lead max. + C min. -40 C Lead screw alignment left Lead screw alignment right screw clamp as accessories Page 13 Stroke lengths 0 mm 0 mm More dimensions on request. and dimensions [mm] Lead Max. stroke length Weight dditional Max. static load capacity Max. RPM Max. speed Product finder SLT-BB-0412 (per 0 mm) axial radial [kg] [kg] [N] [N] [1/min] [m/min] Tr08x ,000 Sg08x drylin E compatible Can be configured as ready-to-connect axis with motor and initiators SLT-BB-04 Tr12x , Tr12x Sg12x In accordance with EC Directive /65/EU (RoHS 2) Restriction (of the use of certain) hazardous substances SLT-BB-0412 l H l l2 ha sg tk kt tg f lb d T as M M Tr08x SLT-BB M M Tr12x Online tools and more information 3D-CD files, prices and delivery time online

36 My sketches general drive technology SLN Based on lubrication-free N low profile guide Trapezoidal or high-helix lead screw drives Compact design Low-cost Dynamic due to leadscrew drive with ball-bearing 12 Online tools and more information

37 SLN Miniature dvantages Compact, precise and lubrication-free Support blocks from corrosion resistant, robust plastic Lead screw mounted with plain or ball bearings Low-cost, robust plastic carriages (basic series 03) Carriage with manual height clearance adjustment (standard series 04) Metal thread inserts Minimal backlash with preloaded nut (preload series 05) Rail made from anodised aluminium Lubrication-free miniature module SLN SLN axes provide a solution for compact installation spaces. The axis measures 28 x 22 mm and can be configured with stroke lengths of up to 250 mm. Thanks to the plastic glides, it runs extremely quietly and is also very light. The axis is based on the tried-and-tested N system, size 27. It is available both mounted on plain bearings or with ball bearings in the shaft end supports. The SLN axis can be adjusted manually using the hand wheel or combined with the E stepper and DC motors. Ura-compact design 3 carriage types (basic/adjustable/preload) Lubrication-free low profile guide Modular design Typical application areas Sensors Inspection technology Laboratory technology Medical technology SLN Miniature Product range Miniature module, Basic version drylin E compatible Single parts made from aluminium and plastic Entry-level model Lead screw mounted with plain bearings Retrofitting possible vailable accessories Page 13 vailable with motor Page 1261 ha l2 lb Øts SLN T hw l + l + stroke Hub t l Pitch Carriage version 03: Basic Dimension Standard lb H SLN Lead screws made from stainless drylin E compatible steel with pitch M5 (5x0.8 mm) or high helix thread (5x5, 6x12.7) vailable hand wheels Page 13 Configurable with motor as a ready to install drive ( E Page 1259) vailable in 3-8 days Detailed information about delivery time online. Block pricing online No minimum order value. From batch size 1. Length of carriage: 35 mm Stroke lengths: up to 250 mm Product finder Max. stroke Weight dditional Max. static load capacity Max. Max. drive length (per 0 mm) xial Radial speed torque [mm] [kg] [kg] [N] [N] [U/min] [Nm] SLN I H E 2) l hw lb ts t T 98) l2 ha ± ±0.2 ±0. ±0. ±0. ±0.2 ±0.2 SLN M ) The dimension E can only be found in conjunction with the igus motor connection 98) Thread/remaining thread visible 1232 Online tools and more information 3D-CD files, prices and delivery time online

38 drylin SLN drylin SLN Miniature Product range Miniature module, preload version SLN Based on maintenance-free drylin N low profile guides size 27 BB-version (ball bearing) for low backlash run Manual and motorised operation possible Linear carriage with individual height clearance adjustment and optional preload vailable accessories Page 13 vailable with motor Page 1261 Pitch: 0008: M5x : SG5x5 0025: DS6.35x : SG6.35x : DS6.35x25.4 Carriage version 4: Standard, adjustable 5: Standard, preload Shaft end support type 0: Plain bearing 1: Ball bearing drylin N size 27 Linear module l2 hw ha H T drylin E compatible l +l stroke + Hub l t lb lb s Øt drylin general drive technology cantilever axis and dimensions [mm] Max. stroke length1) Weight [mm] SLN SLN SLN SLN-27- SLN SLN SLN SLN-27- H [kg] xial Radial Max. speed Max. drive torque [kg] (per 0 mm) [N] [N] [U/min] [Nm] ) l dditional Max. static load capacity I ± ±0.2 ±0. ±0. ± hw ±0.2 ± lb ts tg M3 5 M3 Ø4h9 98) M3 5 M3 Ø4h9 98) Fixed stroke lengths for SLN option: 0/0/0/250 mm The dimension E can only be found in conjunction with the igus motor connection 98) Thread/ remaining thread visible 1) 2) 1234 Online tools and more information 98) Ø Dynamic Rack and pinion drive Light and compact l2 ha Ideal as z axis in robots Lubrication and maintenance-free

39 cantilever axis dvantages Small and dynamic W profile rail made from hard anodised aluminium Drive: toothed rack from polymers Linear carriages with integrated motor connection Lubrication-free cantilever axis The GRW cantilever axis was specifically designed for pick & place applications. Due to the direct rack drive, the GRW axis provides high dynamics for small loads and is the ideal z axis in mui-axis portals. Dynamic force transmission through rack For loads up to 1 kg Completely lubrication-free operation ssembly option for limit and reference switch cantilever axis Product overview Direct drive via rack GRW cantilever axis Direct dynamic force transfer via rack Stroke lengths up to 0 mm Ideal as z axis in mui-axis linea robots Page 1238 GRQ gripper axis Drive via toothed hollow square profile section Very light and compact design For loads up to 500 gr with a Speeds up to 0.7 m/s Page 1239 cantilever axis E stepper motors with or without encoder Typical application areas Mui-axis robots Test and measuring equipment Pick & place applications vailable in 3-8 days Detailed information about delivery time online. Block pricing online No minimum order value. From batch size 1. Stroke lengths up to 0 mm GRW axis in the line robot GRW as z axis in the line robot DLE-LG-001 Ready-to-fit with NEM stepper motors Linear robot systems available from stock Page 1292 GRQ in lift/swivel unit GRQ in lift/swivel unit HSQ Compact unit for lifting and swivelling tasks Ready to install with NEM stepper motors Page 1240 dapter plate and connection bracket available for integration into mui-axis robots drylin E compatible Configurable with motor as a ready to install drive ( E Page 1259) 1236 Online tools and more information 3D-CD files, prices and delivery time online

40 B L l + Hub kt H1 cantilever axis GRW Cantilever axis Product range Dynamic z axis for robot structures GRQ Gripper axis Product range Extremely light axis for pick& place cantilever axis Direct force transfer via rack Compact structure For loads up to N vailable accessories Page 13 vailable with motor Page 1261 Toothed, hard anodised and corrosion resistant square hollow section Loads up to 500 g with a speed up to 0.7 m/s iglidur J plain bearings Drive: NEM stepper motor with gear wheel drylin E compatible M* H tg f hw E4 sg l + stroke L max. tg tk Stroke length Weight dditional Max. feed rate Max. load [mm] [kg] (per 0 mm) [mm/rev] axial [N] GRW GRW-06-B F v L max H1 B tg tk kt B Q D2 [N] [m/s] GRQ L I H E4 l hw f M 131) tg sg GRW-06- GRW-06-B M4 M M4 M ) Depending on the type of motor 1238 Online tools and more information 3D-CD files, prices and delivery time online

41 H2 H3 H1 L max cantilever axis HSQ pivoting/lifting unit Product range Compact, modular and lubrication-free Toothed, hard anodised, corrosion resistant square hollow section Combination with iglidur J slewing ring element Modular design Drive: NEM stepper motor Q S tg B Further motors on request/suitable initiators available Ds general drive technology tooth be axis ZLW F vl vr Lmax (Ds) B H1 (H2) (H3) Q tg S [g] ±0. ±0. ±0. ±0.3 h9 HSQ Order example: HSQ xxx--L--L (incl. stepper motor NEM / with stranded wire) HSQ xxx--E--E (incl. stepper motor NEM / with encoder) Lubrication-free based on W guides Drive: toothed be For fast positioning End supports with grooved ball bearings s single axis or for mui-axis robots 1240 Online tools and more information

42 ZLW Toothed be axes dvantages Fast and powerful Shaft end supports made from robust plastic with integrated ball bearing Deflection axis, square, with tooth rim made of dry-tech high-performance polymer or single-section stainless steel shaft with drive pulley The complete carriage consists of four lubrication-free W individual bearing housings and anodised aluminium assembly plates Carriages available in 3 different lengths High profile, torsion-resistant W double shaft profile, made from hard anodised aluminium Wear resistant PU timing bes with steel reinforcement or Neoprene with fibreglass Lubrication-free toothed be axes ZLW The toothed be axes in the ZLW series are suitable for many different positioning and adjustment tasks. The lubrication-free W profile guide acts as a guide and a toothed be acts as a drive. The stroke is individually selectable. Thanks to the lightweight design using plastic and aluminium, ZLW toothed be axes have a low mass inertia, making them highly efficient. Whether as an individual system or a robot structure, the ZLW series offers the ideal solution in both confined spaces and applications that require a high level of torque support. ll ZLW toothed be axes can be ordered ready for connection and configured with E stepper and DC motors. It is also possible to integrate other motor components. Completely lubrication-free operation 3 types: Eco/basic/standard Variable carriage lengths Muiple motor kits available ZLW Toothed be axes Product overview Positioning with lubrication-free toothed be drive ZLW series Eco ZLW series Basic Low-cost starter axis in 2 sizes Cost-effective deflection axis consisting of stainless-steel Lightweight square section and high-performance polymer Carriage and deflection housing made of plastic Neoprene toothed bes with fibre glass reinforcement nodised W aluminium profile section Hard anodised W aluminium profile Page 1250 For installation sizes 06 and 40 Page 1250 ZLW series Standard ZLW specialists Effective PU toothed be with steel coatings Deep-freeze LT version for applications down to - C Single-section deflection axis made of stainless steel UW version for under water use (shaft and tooth rim) SW version for splash water applications Hard anodised W aluminium profile For installation size 40 For installation sizes 06/40/80/16 Page 1250 Page 1250 Profile grooves for mounting via the slot nuts or the clamping elements Typical application areas Medical and laboratory technology Handling Positioning tasks (pick & place) Camera/sensor adjustment Machine construction ZLW-OD opposite For quick reverse positioning Fast right/left adjustment ZW cantilever axis Secure mounting of the drive unit Traversing of profile section and load vailable in 3-8 days Compact due to flat W double rails With angle flange Fixed end block and floating shaft end support Size 40 for max. stroke up to 1,000 mm Left or right hand Detailed information about delivery time online. Page 1252 Page 1254 one-sided drive shaft, also available as dual-sided for robot structures Block pricing online No minimum order value. From batch size 1. ZLW open design in installation size Variable shaft span of 1/1/0 mm drylin E compatible Configurable with motor as a ready to install drive ( E Page 1259) Carriage lengths: -250 mm Carriage widths: 54-7 mm Stroke lengths: up to 3,000 mm Product finder Effective deflection axis and toothed be Low weight aluminium version available Corrosion-resistant stainless steel version available Page 1256 Motors and mounting accessories Page Online tools and more information 3D-CD files, prices and delivery time online

43 ZLW Toothed be axes Be drive axis Type Shafts-Ø Weight Max. stroke length 1) Transmission Tooth profile Carriage length Max. radial load Toothed be material Toothed be width Toothed be tension Guide bearing Max. speed Max. position variation Idle torque Max. drive torque without stroke 0 mm stroke ZLW [mm] [kg] [kg] [mm] [mm/u] [mm] [N] [mm] [N] [m/s] [mm] [Nm] [Nm] E B S...-OD-B...-OD-S ZLW E B S LT UW SW...-OD-B...-OD-S ZLW S ZLW S ECO Basic Standard reverse Basic reverse Standard ECO Basic Standard Deep-freeze Underwater Splash water reverse Basic reverse Standard Standard Standard ,000 1,000 1,000 1,000 1,000 2,000 2,000 2,000 1,000 2,000 1,500 1,500 2,000 3, HTD 3M HTD 3M MTD3 HTD 3M HTD 3M RPP 3M RPP 3M T5 T5 T5 T5 RPP 3M T5 T5 T5 /0 /0 /0 /0 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0 0/0/0/ Neoprene with GF Neoprene with GF PU with steel Neoprene with GF PU with steel Neoprene with GF Neoprene with GF PU with steel TPUKF2 PU + ramid PU + Stainless steel Neoprene with GF PU with steel PU with steel PU with steel Ball bearing Ball bearing Ball bearing Ball bearing Ball bearing Ball bearing Ball bearing Ball bearing Cold ball bearing xiros ball bearing stainless steel ball bearing Ball bearing Ball bearing Ball bearing Ball bearing ± 0.40 ± 0.35 ± 0. ± 0.35 ± 0. ± 0.35 ± 0. ± 0. ± 0. ± 0.50 ± 0. ± 0. ± 0. ± 0. ± Tightening torque for connections between metal parts Metric thread (Da) Torque Recommended torque [Nm] [Nm] M3 M4 M5 M Note the minimal screw in depth for aluminium and zinc parts: x Da 1) When configuring your module, we ask that you note the igus specifications for maximum stroke lengths. The performance and load specifications shown above for all drive units are based exclusively on stroke lengths within the recommended values. Exceeding these can resu in undesirable effects to the function such as increased wear and noise. Be or lead screw contact cannot be excluded, and the rated performance and load specifications may not be attainable Online tools and more information 3D-CD files, prices and delivery time online

44 ZLW-06 ZLW-40/ Drive torque [Nm] Drive torque [Nm] Drive torque [Nm] Drive torque [Nm] Load capacity [kg] Load capacity [kg] Load capacity [kg] Load capacity [kg] Diagram 01: Required drive torque 138) ; horizontal orientation ZLW-06, Version basic 02 Diagram 02: Required drive torque 138) ; vertical orientation ZLW-06, Version basic 02 Diagram 07: Required drive torque 139) ; horizontal orientation ZLW-40, Version basic 02 Diagram 08: Required drive torque 139) ; vertical orientation ZLW-40, Version basic Drive torque [Nm] Drive torque [Nm] Drive torque [Nm] Drive torque [Nm] Load capacity [kg] Load capacity [kg] Load capacity [kg] Load capacity [kg] Diagram 03: Required drive torque 138) ; horizontal orientation ZLW-06, Version standard 02 Diagram 04: Required drive torque 138) ; vertical orientation ZLW-06, Version standard 02 Diagram 09: Required drive torque 139) ; horizontal orientation ZLW-40/80, Version standard 02 Diagram : Required drive torque 139) ; vertical orientation ZLW-40/80, Version standard ) ssumption: the moving mass is located in a circumscribed circle with a max. R: 0 mm to the middle of the guiding rail, max. permissible torque ZLW-06 Basic 02: 0.75 Nm, a: 0 m/s 2, ZLW-06 Standard 02: 1 Nm, a: 0 m/s 2, constant drive without nominal acceleration value 139) ssumption: the moving mass is located in a circumscribed circle with a Max. R: 0 mm to the middle of the guiding rail, max. permissible torque ZLW-40/80 Basic 02: 1.75 Nm, a: 0 m/s 2, ZLW-40/80 Standard 02: 2.4 Nm, a: 0 m/s 2, constant drive without nominal acceleration value Carriage speed [m/s] ZLW-40/80-Standard ZLW-40-Basic ZLW-06-Standard ZLW-06-Basic Load [N] mm 0.5 mm 1.0 mm mm ,000 1,0 1,0 Carriage speed [m/s] ZLW-40/80-Standard ZLW-40-Basic ZLW-06-Standard ZLW-06-Basic Load [N] mm 0.1 mm 0.5 mm1.0 mm 2.0 mm ,0 1,0 1,500 1,700 1,900 2,0 Carriage loads [N] Length between supports [mm] Carriage loads [N] Length between supports [mm] Diagram 05: Maximum load compared: ZLW-06 and ZLW-40/80, 0 % OT (On-time). The diagram accounts for the sum of all forces active on the carriage. Diagram 06: Sag between unsupported end blocks ZLW-06, Version basic 02 and standard 02. Sag permissible up to 2 mm maximum. Diagram : Maximum load compared: ZLW-06 and ZLW-40/80, 0 % OT (On-time). The diagram accounts for the sum of all forces active on the carriage. Diagram 12: Sag between unsupported end blocks ZLW-40, Version Basic and ZLW-40/80 Version Standard 02. Sag permissible up to 2 mm maximum, horizontal orientation 1246 Online tools and more information 3D-CD files, prices and delivery time online

45 ZLW-16 ZLW Toothed be axes Product overview Drive torque [Nm] M (a=1 m/s²) Nm M (a=0 m/s²) Nm M (a=5 m/s²) Nm M (a=3 m/s²) Nm M (a= m/s²) Nm Load capacity [kg] Diagram 07: Required drive torque 140) ; horizontal orientation ZLW-16, Version standard 02 Drive torque [Nm] M (a=0 m/s²) Nm M (a=3 m/s²) Nm M (a=1 m/s²) Nm M (a=5 m/s²) Nm M (a= m/s²) Nm Load capacity [kg] Diagram 08: Required drive torque 140) ; vertical orientation ZLW-16, Version standard 02 Eco series Many infeed movements require cost-effective axes that focus on pure adjustment tasks. This eco series with toothed be was developed for the fast positioning of light loads. By the compact design and low weight due to aluminium and plastic, the ZLW eco is the perfect aernative to self-made solutions. Basic series Lubrication-free guide also driven by a toothed be made from fibre glass reinforced Neoprene (black). The deflection shaft, consisting of a square stainless steel and toothed pulley made of high-performance polymer, rests on 2 grooved ball bearings. The drive pin is 6x6 mm square and made of stainless steel. The scope of supply includes a plastic adapter for a pin diameter of mm. Carriage speed [m/s] Standard series The lubrication-free guide is also driven by a toothed be made from steel reinforced polyurethane (white). Deflection shaft and drive pulley single-piece are made from plated steel or stainless steel. The pulley shafts are mounted in two deep grooved ball bearings ,000 1,500 2,000 2 Carriage loads [N] Diagramm 05: Maximal load, horizontal installation; the diagram accounts for the sum of all forces active on the carriage. 138) ssumption: the moving mass is located in a circumscribed circle with a Max. R: 0 mm to the middle of the guiding rail, max. permissible torque ZLW-16 Standard 02: Nm, a: 0 m/s2, constant drive without nominal acceleration value The ZLW specialists LT for use at temperatures down to - C, the drive and deflection shaft end supports are fitted with cold ball bearings. Drive is a toothed be suitable for low temperatures. SW the "SW" ZLW version is suitable for applications where there is contact with spray water. Corrosion-resistant due to PU toothed be with stainless steel tie beams and stainless steel ball bearings, as well as shaft-end support housing made of anodised aluminium. UW maximum protection against corrosion is provided by the toothed be axis; for underwater applications, among others. Linear carriages, drive and deflection shaft-end supports made of anodised aluminium, incl. lubrication-free xiros ball bearings. flexible toothed be with aramid tie beams serves as the be. More Information online Online tools and more information 3D-CD files, prices and delivery time online

46 ZLW toothed be axes ZLW Toothed be axes Product range Toothed be axis in versions Eco, Basic and Standard ZLW Toothed be axes Product range ZLW toothed be axes complete Page 1258 ZLW B Design E: Type series Eco (06/40) B: Type series Basic (06/40) S: Type series Standard (all sizes) Version 02: With grooved ball bearings Fast positioning of small loads Installation size Quiet operation and flat design Be drive axis Drive shaft on one or both sides Linear carriages available in different lengths (except of the Eco version) specialists ZLW-40-LT-02-S Configurable with motor as a ready to install drive Page 1284 Specialst in deep-freeze, underwater and spray-water areas Page 1251 Design S: Design standard Version 02: With grooved ball bearings I + stroke Options LT: For cold applications up to - C UW: For underwater applications SW: For splash water applications Type Be drive axis I H l R f sg ha hc lz l2 Connecting dimensions ZLW ZLW ZLW-40-LT-02-S ZLW-40-UW-02-S ZLW-40-SW-02-S ZLW ZLW ±0. ±0. ±0. ±0.3 h M T2 nh nw dp Connecting dimensions [mm] X E P Lp dp n nb nw nh T1 T2 d d ± ±0.25 ±0.25 ZLW variable T1 P ZLW variable n nb ZLW-40-LT-02-S variable hc Lp ZLW-40-UW-02-S ZLW-40-SW-02-S variable variable X E ZLW ZLW variable variable M Online tools and more information 3D-CD files, prices and delivery time online

47 W l2 ha Ht ZLW toothed be axes ZLW Toothed be axes Product range Opposed be drive with angle flange ZLW Toothed be axes Product range ZLW toothed be axes ZLW-40-OD-02 Quick reverse positioning T1 Fast right/left d adjustment vailable as standard and basic versions Incl. angle flange for fixing Individual stroke lengths up to max. 3,000 mm Radial loads up to 0 N dw1 W2 s W l2 f W2 T2 T2 W f Ws l2 T2 W l2 complete Page 1258 Version 02: With grooved ball bearings dw1 W1 lz Hub stroke + L sg l Design OD: Right/left and reverse Type Be drive axis Hub stroke+ LW W1 ngle flange alignment lz l Option 02 mounted on the side, ZLW alignment on the edge I H Ht L R f sg ha lz Max. stroke length 0.3 ±0. ±0. ±0. ±0.3 [mm] Ws I + stroke Hub stroke + L IW + stroke Hub stroke+ LW sg ZLW-06-OD 9) ZLW-40-OD ZLW-16-OD-02 ZLW-16-OD-03 ZLW-16-OD M4 14 1, , , , ,000 Option 04 mounted horizontally, ZLW alignment horizontal Option 03 T1 d mounted on the front W2 dw1 W1 T1 lz d W2 dw1 W1 lz l l l2 d T1 T2 Ws W1 W2 dw1 lw W h9 ±0.25 ±0.25 ZLW-06-OD 9) ZLW-40-OD ZLW-16-OD-02 ZLW-16-OD-03 ZLW-16-OD M5- deep M5- deep M5- deep ) Basic version: 6 mm square, plastic adapter for pin diameter mm included Ws 1252 Online tools and more information Hub stroke + L 3D-CD files, prices and delivery time online sg Hub stroke+ LW sg

48 l ZLW toothed be axes ZLW Toothed be axes Product range Cantilever axis ZLW Toothed be axes Product range ZLW toothed be axes complete Page 1258 ZW S-0-L-500 Stroke length max. 1,000 mm Drive unit fixed, only profile and load are moved Hard-anodised aluminium axis profile Lightweight Max. stroke 1,000 mm Max. axial load 50 N llowed moment for carriage M y max : Nm Drive shaft L: Drive shaft left R: Drive shaft right L/R: Drive shaft both-sides Carriage length 0: 0 mm Design S: Standard Version 02: With grooved ball bearings B2 Type f ff H2 fa a E4 Cantilever axis H htf B4 a ha E5 l LG + stroke E6 1 drive shaft right Viewing direction x B B7 2 drive shaft left E7 Moving end block ZTF lz d l7 Fixed end block ZT H H2 LG l ha d l l7 lz 0.3 ±0.3 ±0.1 h9 +1 ±0. ±0. ZW Connecting dimensions ZW-40 B B2 htf f ff fa a E4 B4 B7 E5 E6 E7 0.3 ±0.3 ±0.1 h9 ±0.1 ±0. ± Online tools and more information 3D-CD files, prices and delivery time online

49 ZLW toothed be axes ZLW Toothed be axes Product range ZLW Toothed be axes Product range ZLW toothed be axes ZLW-1-L-02-S-0-H-00 luminium version Dynamic due to drive and end support shafts supported on ball bearings Robust wide round bes Central be adjustment at the carriage Based on lubrication-free W guide system Variable motor connection due to solid and hollow shafts d3 g3 H l + stroke l + Hub I ha f Stainless steel version Stroke length: max. 3,000 mm Drive shaft: Hollow shaft Carriage length 0: 0 mm Version S: Standard Version 02: With grooved ball bearings Design L: luminium ES: Stainless steel xis distance 1: 1 mm 1: 1 mm 0: 0 mm Type Be drive axis lz lu C4 ØD K V 2 E4 Max. stroke length Transmission Tooth profile Be drive -material -tension [mm] [mm/u] [N] at ZLW-1 ZLW-1 ZLW-0 3, M PU with steel cable 750 3, M PU with steel cable 750 3, M PU with steel cable 750 I H E4 C4 f ha lz l h7 ZLW-1 ZLW-1 ZLW d3 g3 D K at 2 lu V For DIN912 - [mm/rev] ZLW-1 ZLW-1 ZLW-0 M M M Online tools and more information 3D-CD files, prices and delivery time online

50 ZLW Toothed be axes complete system: ZLW-06-OD-02-B--L-00 Stroke length ZLW-06: Max.1,000 mm, OD-Version max. 1,000 mm ZLW-40: Max.2,000 mm, OD-Version max. 1,500 mm ZLW-80: Max. 2,000 mm ZLW-16: Max. 3,000 mm Drive shaft L: Drive shaft left R: Right-hand drive shaft L/R: Drive both sides Length of carriage : mm 0: 0 mm 0: 0 mm 0: 0 mm 250: 250 mm Design S: Type series standard B: Type series basic E: Type series Eco Version 02: With grooved ball bearings Options OD: Reverse (06/40) LT: For cold applications (40) UW: For underwater applications (40) SW: For splash water applications (40) Type x Viewing direction Be drive axis 1 left 2 right Drive shaft 1258 Online tools and more information