Reservoir Equipment. Global Filtration Technology

Transcription

1 Reservoir Equipment Global Filtration Technology

2 E Series PPLICTIONS TECHNICL DT The breather has been designed to achieve a low pressure drop and high dirt holding capacity with airflow up to 5 l/min. Construction: Glass reinforced composite housing with Eco-element. Typical pplications gricultural Machines rticulated Dump Trucks Forestry Equipment Wheeled Loaders Lubricating Systems Excavators Mobile Cranes Filter Media Options: P2: High quality polyester media. Degree of filtration 2µm (abs). C5: Polyester media with water-resistant layer. Degree of filtration.5µm (abs) Q: Glass fibre media. Degree of filtration.µm (abs) Mounting Options: With 6 screws. Includes machine and plate screws, a strainer and gaskets. External threads G3/4, G abd M33x2. Internal thread G3/4. PRESSURE DROP CURVES p total = p housing + p element. p (kpa) Housing (Without Element) GE Q (dm 3 /min) EC2 C5 Industrial Power Units Options: Visual gauge type vacuum/pressure indicator. Overpressure valve, pressure setting.2 bar. dvantages of the new E2: Easy maintenance. Indicator states the need for element change. Quick and easy element change with no tools. Environmentally Friendly: E2 element contains no metal parts: therefore it can be crushed and burned minimising the volume of waste material. Other Features: The optional indicator is located in a safe place inside the housing. Housing includes mounting holes for a padlock, which allows you to increase the security against theft and vandalism. The recommended level of the initial pressure drop for this filter is max.2 bar (2. kpa). GS2 GE6 ME33 p (kpa) EC2 P Q (dm 3 /min) EC2 Q IN>OUT OUT>IN p (kpa) IN>OUT OUT>IN p (kpa) IN>OUT OUT>IN Q (dm 3 /min) Q (dm 3 /min) 92

3 E Series SPECIFICTION E OPTIONL INDICTOR 4 (4.49) HOLES FOR LOCKING 2 (4.2) IR FLOW Q = 5 l/min max 43 (.69) OPTIONL MOUNTING Y 6 SCREWS These holes are always open providing drainage of splash water Ø73 (2.87) Ø9 (3.54) mm (inches) G 3 /4 OPTIONL MOUNTING G M33x2 G 3 /4 NOTICE! reather is an essential part of the system and the element needs to be replaced regularly. 6 HOLE FIXING MOUNTING DIMENSIONS 6 x 6 Ø4 or M ORDERING EXMPLE ELEMENT Table Table 2 Table 3 Table 4 Complete Filter: E2 Table Replacement Element: EC2 Table Table 2 Table 3 Filtration Media & Degree of Filtration Polyester media 2. microns absolute Water-resistant media.5 microns absolute Glass fibre media. microns absolute CODE P2 C5 Q Mounting Options Standard 6 holes arranged with diam. 73mm External thread G 3 /4 External thread G Internal thread G 3 /4 External thread M33x2 CODE HC73 GE2 GE6 GS2 ME33 Overpressure Valve Options No overpressure valve Overpressure valve setting.2 bar CODE V2 Table 4 Indicators Options No indicator Vacuum/Pressure gauge CODE 93

4 L Series PPLICTIONS SPECIFICTION ssembly: Tank top mounted Connections: Threads G /4 (ISO228), /2 (UN-6-2) Seal Material: Seals integrated in Leif element Operating Temperature Range: -2 to +8 C Filtration Media: 3 micron Flow Fatigue Characteristics: Filter media is supported so that the optimal fatigue life is achieved PRESSURE DROP CURVES Pressure Loss Curve L The Parker Filtration L- and L-2 Series ir reathers. High performance air breathers are often applied when it comes to optimal protection of hydraulic and lubrication systems from contamination. The L- has a flow capacity of l/min, the larger L-2 is capable of handling 2 l/min. oth are equipped with a base plate featuring a SP port or a UN thread, and 3-micron replaceable Leif elements. The L is equipped with a reusable cap. The visual indicator of the L-2 (optional for the L-) indicates when the air breather element requires replacement. n extension mounting adaptor and an adaptor with filling connection are available as accessories. Vacuum Indicator: L- on request only, L-2.4 bar. Visual with latch out memory. reather Housing: High impact strength composite Filter Element: Leif element Options: daptor with filter connection Single adaptor reather with integrated pressure relieve valve for pressurised tank on request only Leif elements can be applied for hydraulic fluids only. For other fluids contact Parker Filtration. Typical pplications Saw Mills gricultural Machines rticulated Dump Trucks Forestry Equipment Wheeled Loaders Lubricating Systems Excavators Industrial Power Units Mobile Cranes Pressure Loss Curve L2 Flow (US GPM) Flow (US GPM) p (mbar) 2.5 delta-p p (mbar) Flow (l/min) Flow (l/min) PREFERRED PRODUCTS TLE Ordering Code L-G /4QXWL-3- L-2G /4QXWL-3V Flow (l/min) 2 Media Rating GDL 3 GDL 3 Ports G /4 G /4 Indicator Visual Replacement Elements QXWL-3 QXWL-3 NOTE: Filters ordered from the Matrix on the next page are on extended lead times. Where possible, please make your selection from the table above. 94

5 SPECIFICTION L- L-2 Reservoir Equipment L Series 5 (NO INDICTOR) 4 (35.5) NOTICE! reather is an essential part of the system and the element needs to be replaced regularly. 25 TOP VIEW ISO228-G /4 OPTIONL: /2-6UN-2 46 /F Ø27 /2-6UN-2 (Optional: ISO228-G /4) SLW46 Ø27 25 TOP VIEW EXTENSION ND FILLING MOUNTING DPTORS DPTOR SINGLE DPTOR WITH FILLER CONNECTION xØ7(PCDØ73) 6xØ7(PCDØ73) Ø /2 SP ORDERING EXMPLE ELEMENT 3 QXWL-3 ORDERING EXMPLE IRRETHER L G /4 QXWL L2 G /4 QXWL-3 V Table Table 2 Table 3 Housing l/min 2 l/min Table 5 reather Type Options daptor Single With filler connection CODE L- L-2 CODE SNG FP Ø85 reather Connection Ports ISO 228-G /4 (SP) /2 UN-6-2 CODE G /4 U /2 ORDERING EXMPLE DPTOR Std 2 5 DPTOR L G /4 FP Std 2 5 DPTOR L G /4 SNG Element L- L-2 Degree of Filtration 3µm CODE QXWL-3 QXWL-3 Table 4 Indicator No indicator Visual Indicators CODE V 95

6 IP65 Rated Filler reather Filters SPECIFICTION FOR SINGLE ND 6 HOLE INSTLLTION Option Construction: Moulded in non-corrodible glass-filled nylon combining strength with a lightweight design. Options: () Single (63mm Dia) Hole Filler reather installation that eliminates drilled and tapped holes using self-locking clamps. (2) 6 Hole Filler reather Installation that uses 6 x No thread forming screws. (3) 3 Hole Filler reather option is available Self- Locking Clamps (Single Hole Option): 3 x Zinc and clear chromate plated steel screws.spring steel clamps. Strainers: Unique design diffuses oil flow into the reservoir. () Single length in Polypropylene (95mm length) (2) 2-piece telescopic in Polypropylene (95mm length max.) Filtration Element: Expanded Polyurethane foam, micron. Seals: Nitrile. Working Temperature: -3 C to +9 C. Pressurised Filler reathers: vailable in 3 pressure options to reduce the risk of contamination. Pressurisation Options:.2,.35 and.7 bar crack pressure. OPTION FILLER RETHERS (SINGLE HOLE INSTLLTION) Ø Pressurisation Value: Nylon/Nitrile. Dipstick: vailable for use with options and 2. Dipsticks are available in 2 lengths and in packs of. Dipstick Material: S. Hi/Lo Indicators: cetal. djustable Red/Green level indicators. Dipstick Lengths: 2mm and 4mm. reather Weight:.2Kg. nti-splash Feature: The unique design anti-splash feature is standard on all Options and 2 and allows for a dipstick to be fitted if required..98xxx Pressurised Pressure Drop Curves Valve MX p (bar) Valve.2 Valve Ø Flow I/sec (ir).98xxx Non-Pressurised Pressure Drop Curves Option. Single Hole Filler reathers pressurised Supersedes Description.9822.UC.9822.UC UC.9823.UC.9823.UC UC.9827.UC.9827.UC UC FI.2P FI.2P FI.C2P FI.C2P FI.C2P FI.CC2P FI.D2P FI.D2P FI.DC2P micron pressurised..2 bar without strainer micron pressurised..2 bar with 95mm strainer Ø7. micron pressurised..2 bar with telescopic strainer micron pressurised..35 bar without strainer micron pressurised..35 bar with 95mm strainer micron pressurised..35 bar with telescopic strainer micron pressurised..7 bar without strainer micron pressurised..7 bar with 95mm strainer micron pressurised..7 bar with telescopic strainer p (bar).5..5 With nti-splash Without nti-splash 5 5 Flow I/sec (ir) Option. Single Hole Filler reathers non-pressurised Supersedes Description.982.UC.982.UC.9822.UC FI.2P FI.2P FI.C2P.5 micron filler breather without strainer micron filler breather with 95mm strainer micron filler breather with telescopic strainer 96

7 FILLER RETHERS (6 HOLE INSTLLTION) Option 2 Note. Un-pressurised 6 hole fixing: Reservoir Equipment IP65 Rated Filler reather Filters Form 6 off tank mounting holes between Ø4. and 4.4mm (dependent on the material and thickness see guide below) equispaced on 7-73mm P.C.D. to suit No. thread forming screws supplied. Note 2. Pressurised 6-hole fixing: Form 6 off tank mounting holes between Ø4. and Ø4.4mm (dependent on the material and thickness see guide below) equispaced on 73mm P.C.D. to suit No. thread forming screws supplied. Ø Note 3. Reservoir mounting guide Sheet thickness mm Hole size mm Ø 27 Telescopic Strainer The telescopic strainer design is ideal, where reservoir depth allows, to increase the surface area of the strainer, improving still further its straining ability and oil flow-through and allowing for longer dipstick lengths Ø3 Ø42 Option 2. 6-hole filler breathers pressurised Supersedes Description.9882.UC.9882.UC UC.9883.UC.9883.UC UC.9887.UC.9887.UC UC FI.D2P FI.D2P FI.DC2P FI.DC2P FI.DC2P FI.DCC2P FI.DD2P FI.DD2P FI.DDC2P micron pressurised..2 bar without strainer micron pressurised..2 bar with 95mm strainer micron pressurised..2 bar with telescopic strainer micron pressurised..35 bar without strainer micron pressurised..35 bar with 95mm strainer micron pressurised..35 bar with telescopic strainer micron pressurised..7 bar without strainer micron pressurised..7 bar with 95mm strainer micron pressurised..7 bar with telescopic strainer Ø42 Option 2. 6-hole filler breathers non-pressurised Supersedes Description.988.UC.988.UC.9882.UC FI.D2P FI.D2P FI.DC2P micron filler breather without strainer micron filler breather with 95mm strainer micron filler breather with telescopic strainer 6x Ø

8 Filler reather Filters OPTION 3 FILLER RETHERS (3 HOLE INSTLLTION) 46 Ø5.5 Ø53 New Options Fully Tested s part of the design development programme for the new IP65 Filler reathers, extensive performance and endurance testing was carried out to ensure durability and efficiency. Ø x Ø hole Filler reathers (6-hole available) Description micron filler breather without strainer micron filler breather with 95mm strainer Note: Not suitable for use with DIP.26/27 6-hole.689/.6898 available. Note: Form 3 off tank mounting holes between Ø4. and Ø4.4mm (dependent on the material and thickness see chart for guide) equispaced on 4.3 P.C.D. to suit No. thread forming screws supplied. DIPSTICK OPTIONS Dipstick ordering Supersedes Description DIP.26 DIP.27 Dipsticks DIP.F2 DIPF4 Pack x 2mm dipsticks Pack x 4mm dipsticks The dipstick, available in 2 lengths 2mm and 4mm, can be cut to the required length or left as it is and the Hi/Lo indicators moved and positioned on the dipstick itself by squeezing the sides of the indicator and repositioning along the dipstick. 98

9 STNDRD SCREW-ON RETHERS SPECIFICTION Option G /2 and G 3 /4 (Ø) Reservoir Equipment Screw-On Type ir reathers PRESSURE DROP FLOW CURVES Option G /2 or G 3 /4 Supersedes Description.986.UC.9862.UC.9863.UC.9867.UC.984.UC.9842.UC.9843.UC.9847.UC DIP.26 DIP.27.3 FI.C22P FI.C22P FI.CC22P FI.CD22P FI.22P FI.22P FI.C22P FI.D22P DIP.F2 DIP.F4 micron G /2 option un-pressurised micron G /2 option pressurised.2 bar micron G /2 option pressurised.35 bar micron G /2 option pressurised.7 bar micron G 3 /4 option un-pressurised micron G 3 /4 option pressurised.2 bar micron G 3 /4 option pressurised.35 bar micron G 3 /4 option pressurised.7 bar pack x 2mm dipsticks pack x 4mm dipsticks.98xxx Screw-on Non-Pressurised Pressure Drop Curves Construction: Moulded in non-corrodible glass-filled nylon combining strength with a lightweight design. Option : 2 screw on type air breathers are available G /2 or G 3 /4 threaded base models. Filtration Element: Expanded Polyurethane foam, micron. Seals: Nitrile. Working Temperature: -3 C to +9 C. Pressurised ir reathers: vailable in 3 pressure options to reduce the risk of contamination. Pressurisation Options:.2,.35 and.7 bar crack pressure G /2 3 Pressurisation Value: Nylon/Nitrile. Dipstick: vailable for use with all options. Dipsticks are available in 2 lengths and in packs of. Dipstick Material: S. Hi/Lo Indicators: cetal. djustable red/green level indicators. Dipstick Lengths: 2mm and 4mm. reather Weight:.2Kg. nti-splash Feature: The unique design anti-splash feature is standard on Option and allows for a dipstick to be fitted if required. Ø G /2 3 /F HEX.25 p (bar).2.5. With nti-splash Without nti-splash 5 5 Flow I/sec (ir) Note: For pressure drop information on the Option. Pressurised consult Parker Filtration. G 3 /4 Ø 6 96 G 3 /4 3 /F HEX 99

10 Screw-On Type ir reathers COMPCT SCREW-ON RETHERS SPECIFICTION Option 2 G /4, G 3 /8, R /2 and R 3 /4 (Ø4) Construction: G /4, G 3 /8, R /2 and R 3 /4 cap and base plate mouldings in nylon 66. Element: Expanded Polyurethane foam, micron. Pressurised ir reathers: vailable G 3 /8. Pressurisation Options:.2,.35 and.7 bar crack pressure. Pressurisation Valve: Nylon. Dipstick: vailable for use with R /2 and R 3 /4. Dipstick Material: S: G /4, G 3 /8 and mini-series in brass. rass: Mini Series. Hi/Lo Indicators: cetal adjustable red/green level indicators. Dipstick Lengths: 2mm and 4mm (packs of ). reather Weights:.28Kg (G /4, G 3 /8, R /2, R 3 /4) PRESSURE DROP FLOW CURVES p (bar) G/ Flow I/sec (ir) Option 2 G /4, G 3 /8, R /2 and R 3 /4 Supersedes Description.683.UC.68X.UC.68Y.UC.68Z.UC SI.P SI.P SI.CP SI.DP Note: Only available in multiples of micron G /4 option 2 screw-on micron G 3 /8 option 2 screw-on micron R /2 option 2 screw-on micron R 3 /4 option 2 screw-on Note: For pressure drop information on G 3 /8, R /2 and R 3 /4, consult Parker Filtration. Ø4 G /4 Ø4 G 3 /8 2 /F HEX G /4 Ø R /2 Ø4 R 3 /4 6 2 /F HEX G 3 / /F HEX /F HEX 9 4 R /2 R 3 /4 2

11 SCREW-ON TYPE IR RETHERS SPECIFICTION Option 3 G 3 /8, G /2 and G 3 /4 (Ø7) Reservoir Equipment Screw-On Type ir reathers Construction: Mouldings in glass-filled nylon and glass coupled polypropylene. Element: Expanded Polyurethane foam, micron. Seals: Nitrile. Pressurised ir reathers: vailable G 3 /8, G /2 and G 3 / 4, 3 pressure options to reduce the risk of contamination. Pressurisation Options:.2,.35 and.7 bar crack pressure. PRESSURE DROP FLOW CURVES p (bar) G3/8 G/2 G3/ Flow I/sec (ir) Note: For pressure drop information on G 3 /8, consult Parker Filtration. Pressurisation Valve: Nylon. Dipstick: vailable for use with G 3 /8, G /2 and G 3 /4. Dipstick Material: Mini-series in brass. Hi/Lo Indicators: cetal adjustable red/green level indicators. Dipstick Lengths: 2mm and 4mm (packs of ). reather Weights:.75Kg, Mini-series.9Kg. Option 3 G 3 /8, G /2 and G 3 /4 S.5 S.6 S.7 Dipstick Ordering DIP.26 DIP.27 Description micron G 3 /8 non-pressurised screw-on type micron G /2 non-pressurised screw-on type micron G 3 /4 non-pressurised screw-on type Supersedes Description DIP.F2 DIP.F4 Pack of x 2mm dipsticks Pack of x 4mm dipsticks Note: Pressurised versions of G 3 /8, G /2 and G 3 /4 models are available. Consult Parker Filtration. Ø7 G 3 /8 G /2 Ø7 THE MINI-SERIES RETHER Screw-on option Push-fit option Ø G 3 /8 28 /F HEX G /2 28 /F HEX G 3 /4 Ø MIN Ø22 SPOTFCE Ø Ø Ø.8 G / Ø3.55 Ø Description S.683 Gearbox air breather G 3 /4 3 /F HEX 2

12 Filler reather Filters (Metal) Filter flange type Displacement: 72 l/min. Ø76.2 Micron rating: µ/4µ. ir flow:.75m 3 /min. Weight:.27 Kg. (P.73.*.**).24 Kg. (.63.**) Valve Crack Pressure:.35 and.7 bar. ORDERING INFORMTION ir reather Threaded and push-on type Note: Zinc and yellow passivated caps available. Consult Parker Filtration. Supersedes Displacement Rating ir Flow Thread Weight l/min Micron S S.562. S S *P **P *P **P.73.. Supersedes Displacement Rating ir Flow Thread Weight l/min Micron *SP **SP *SP **SP.73.. MI.22P MI.2P MI.C22P MI.C2P MI.E2P Filler reather Filter flange type MI.D2P MI.DP MI.2P MI.P MI.D2P MI.D22P Displacement Rating ir Flow Thread Weight Total ssembly Supersedes Cap ssembly Supersedes l/min Micron MI.D2CP MI.D2DP MI.DCP MI.DDP MI.2C2P MI.2D2P MI.C2P MI.D2P H53-3 H53- H53-4 H53-2 H62-3 H62- Displacement Rating ir Flow Thread Weight Total ssembly Supersedes Cap ssembly Supersedes l/min Micron CP.63.4 CP.63. CP.38.4 CP.38. Filler reather Filter type (Pressurised) *CP **CP **CP **CP.73.. ir reather Threaded type (Pressurised) H62-4 H CPI.D2P CPI.DP CPI.2P CPI.P CPI.D2CP CPI.D2DP CPI.DCP CPI.DDP m 3 /min.45m 3 /min.3m 3 /min.5m 3 /min.75m 3 /min m 3 /min.75m 3 /min.45m 3 /min.45m 3 /min * Valve Crack Pressure.35 bar. **Valve Crack Pressure.7 bar. For dipstick and locking lug options consult Parker Filtration Ø49.5 Ø83 Locking lug option (555 & 556) For added security, certain Parker Filtration Metal Filler reather Filters can be specified with a locking lug option. G 3 /4 G 3 /4 G /4 G /4.75m 3 /min.45m 3 /min.3m 3 /min.5m 3 /min.75m 3 /min.75m 3 /min.45m 3 /min.45m 3 /min G 3 /4 G 3 /4 G 3 /4 G 3 /4.2 Kg.2 Kg.6 Kg.6 Kg.3 Kg.24 Kg.24 Kg.7 Kg.8 Kg.27 Kg.27 Kg.27 Kg.27 Kg.2 Kg.2 Kg.2 Kg.2 Kg 22

13 Filler reather Filters (Metal) Threaded type (Pressurised) Displacement: 72 l/min. Micron Rating: µ/4µ. ir Flow:.75m 3 /min. Weight:.2 Kg. Thread: G 3 /4. Valve Crack- Pressure:.35 and.7 bar G 3 /4 Ø /F HEX Threaded type Ø44.5 Displacement: 27 l/min. Micron rating: µ/4µ. ir flow:.3m 3 /min. Weight:.6 Kg. Thread: G / /F HEX Push on type G /4 Ø38. Displacement: 72 l/min. Micron rating: 4µ. ir flow:.75m 3 /min. Weight:.3 Kg Ø76.2 Filter flange type Ø44.5 RETINING SPRING CLIP Displacement: 27 l/min. Micron rating: µ/4µ. ir flow:.3m 3 /min. Weight:.7 Kg Ø5 TNK INSTLLTION NOTES. Un-pressurised 6 hole fixing Form off tank mounting holes between Ø4. and Ø4.4 (dependant on the material and thickness, consult Parker Filtration) equispaced on P.C.D. to suit No. thread forming screws supplied. RETHER UNITS Small reather Specification THREE SIZE: /4 SPT 3 /8 SPT /2 SPT Ø35 2. Pressurised 6 hole fixing Form 6 off mounting holes between Ø4. and Ø4.4 equispaced on 73. P.C.D. to suit No. thread forming screws supplied H279- H279-2 H Un-pressurised 3 hole fixing Form 3 off tank mounting holes between Ø4. and Ø4.4 equispaced on 4.3 P.C.D. to suit No. thread forming screws supplied. ORDERING INFORMTION Description Small breather /4 SPT thread Small breather 3 /8 SPT thread Small breather /2 SPT thread 23

14 Spin-On ir reathers High capacity air filters designed for the removal of airborne contamination in hydraulic systems to support environmental maintenance. Ideal for high flow systems and heavily contaminated environments. Disposable spin-on elements quickly and easily replaced. 3 micron quality filtration elements. Models available 7 l/min and 3 l/min. Ø Ø MOUNTING FCE FOR STNDRD ND LRGE RETHER 73 PCD Ø57 HOLE IN TNK C D E SPT C Ø88 OSS OR SPOT FCE (.6 MICRON SURFCE FINISH) 6 FITTING HOLES Ø5.6 EQUISPCED ON PCD STRINER 3 MESH (6 MICRONS) Ø48 LRGE RETHER FILLER SPECIFICTION Maximum Operating Temperature: -2 C to +9 C Construction Materials: Epoxy coated steel components to resist corrosion. Resistant paint finish on large reathers Fluid Compatibility: Suitable for use with mineral oils and water oil emulsions Weights: Large: H834-. Kg Small:.2g H Kg H Kg Each breather filler is supplied with mounting gaskets and self-tapping screws. ORDERING INFORMTION Large reather ir Flow Rate C D E H834-4 H l/min 3 l/min /4 /4 Large reather Filler Part ir Flow Replacement breather canisters Number Rate C including bayonet for H834- H834-2 H l/min 3 l/min 3 l/min H834-6 H834-7 H

15 ir reathers High capacity air filters designed for the removal of airborne contamination in hydraulic systems to support environmental maintenance. Ideal for high flow systems and heavily contaminated environments. Disposable spin-on elements quickly and easily replaced. 5 micron quality filtration elements. 2 models available 7 l/min and 5 l/min. vailable with a pressurised valve in the mounting adaptor. STNDRD SPIN-ON IR RETHER STEM Ø94 RESERVOIR CUTOUT Ø25 MXIMUM CIRCUIT SYMOL (STNDRD) 6 Ø5 3 OFF M6 FIXING HOLES EQUISPCED ON 4.3 P.C.D. PRESSURISED SPIN-ON IR RETHER STEM RESERVOIR CUTOUT Ø25 MXIMUM Ø97 Ø63.5 CIRCUIT SYMOL (PRESSURISED) 6 ORDERING INFORMTION 3 OFF M6 FIXING HOLES EQUISPCED ON 5 P.C.D. Note: Spin-on ir reather Elements can also be mounted directly on to any suitable length of 3 /4" SP threaded pipe. 5 micron Spin-on ir reathers Replacement ir Flow Rate mm mm Weight Element S.3456 S l/min 5 l/min Kg.75 Kg Pressurised 5 micron Spin-on ir reathers Replacement ir Flow Rate mm mm Weight Element *S.3458 **S.3459 * S.3454 **S l/min 7 l/min 5 l/min 5 l/min * Valve Crack Pressure.35 bar. ** Valve Crack Pressure.7 bar. Note: The reservoir must be capable of withstanding pressurisation Kg.69 Kg.8 Kg.8 Kg

16 Lockable Filler reathers INSTLLTION DETILS Tank Mounting 5.5 FLP TO PROTECT LOCK Ø5 STRINER LOCKING SCREWS THREDED TYPE T POSITIONS X ND Y 3 LOCKING SCREWS PUSH ON TYPE T POSITIONS X, Y ND Z 3 OFF EQUISPCED CLMPS Stand Pipe Mounting X Ø TNK MOUNTING HOLE 5.5 Z 34 7 Y LOCKLE FILLER RETHER SELECTION Total assembly pressure drop flow curve µ and 4µ elements Flow (US GPM) p (bar) µ 4µ ORDERING INFORMTION LFC LFC LFC LFC LFC LFC.6223 LFC LFC LFC LFC LFC.6224 LFC LFC Flow (l/min) Description Non-breathing (No element) 2 SP thread with strainer Non-breathing (No element) Clamp mounting with strainer µ element, G2 thread with strainer µ element, G2 / 2 thread with strainer µ element, clamp mounting with strainer 4µ element, G2 thread without strainer 4µ element, G2 thread with strainer 4µ element, G2 / 2 thread without strainer 4µ element, push on mounting without strainer 4µ element, clamp mounting with strainer µ vented (air in) G2 thread without strainer µ vented (air in) push on mounting with strainer 4µ vented (air in) push on mounting without strainer 26

17 SPECIFICTION Reservoir Equipment Fluid Level Temperature Gauges INSTLLTION DT For through hole mounting: Thread Hole size M M2 Preferred. 3. Maximum For tapped holes: Holes to be tapped square to mounting face. Tolerance on hole centres: For welded back nuts: The above details should be combined. INSTLLTION ND PPLICTION INFORMTION Simple to Install The universal fixing is designed for either front or rear fixing. Just two holes in the tank threaded for front fixing and the gauge is ready to install. fter positioning the gauge the bolts are simply tightened to provide a secure seal. There is no fear of leakage with the square section seals and the two-point mounting system eliminates problems with tank distortion. M and M2 bolt thread options are available. Easy to Read The high-visibility lens is one-piece for added security and moulded in shatterproof, transparent polyamide for an accurate and clear oil level and temperature indication. Further gauge protection is provided by a specially designed shroud moulded in high-impact, black polystyrene. ORDERING INFORMTION Size. 76mm Centres. M Thread Supersedes Description Centres Thread Max Temp Weight FL. FLT.2 Size. 76mm Centres. M2 Thread Supersedes Description Centres Thread Max Temp Weight FL.3 FLT.23 LGI.2P LGI.22P LGI.2P LGI.22P H36- Fluid Level Fluid Level/Temp Fluid Level Fluid Level/Temp Construction: Lens Transparent polyamide. Lens ase Nylon 66. Shroud High impact polystyrene. No aluminium content. Seals: Nitrile. Maximum working pressure: bar. Working temperature: -3 C to +9 C. Fluid compatibility: Mineral and petroleum based oils. Note: 5mm model with metal shroud finished in black available. Recommended bolt tightening torque: Nm maximum. Thermometer scale range: 3 C to 9 C. Indicator: lue alcohol. Note:. Locate seals in mounting recess before fitting. 2. fter choosing fluid level only or with temperature, select the size required by studying the installation details to determine a part number. SIZE INSTLLTION DETILS DRIVE SLOT mm 76mm 76mm 76mm LCK LINE RED LINE M M M2 M /F HEX C 9 C 9 C 9 C.3 Kg.3 Kg.3 Kg.3 Kg 27

18 Fluid Level Temperature Gauges SIZE 2 INSTLLTION DETILS DRIVE SLOT LCK LINE RED LINE /F HEX Size 2. 27mm Centres. M Thread FL.2 FLT.22 Size 2. 27mm Centres. M2 Thread FL.23 FLT.223 LGI.2P LGI.22P LGI.2P LGI.22P 4.5 ORDERING INFORMTION Supersedes Description Centres Thread Max Temp Weight H36-4 Fluid Level Fluid Level/Temp Supersedes Description Centres Thread Max Temp Weight Fluid Level Fluid Level/Temp 27mm 27mm 27mm 27mm M M M2 M2 9 C 9 C 9 C 9 C.5 Kg.5 Kg.5 Kg.5 Kg SIZE 3 INSTLLTION DETILS DRIVE SLOT LCK LINE /F HEX 7 RED LINE ORDERING INFORMTION Size mm Centres. M Thread Supersedes Description Centres Thread Max Temp Weight FL.3 FLT.32 Size mm Centres. M2 Thread Supersedes Description Centres Thread Max Temp Weight FL.33 FLT LGI.C2P LGI.C22P LGI.C2P LGI.C22P H Fluid Level Fluid Level/Temp Fluid Level Fluid Level/Temp 254mm 254mm 254mm 254mm M M M2 M2 9 C 9 C 9 C 9 C.23 Kg.23 Kg.23 Kg.23 Kg

19 Diffusers INSTLLTION DETILS SPECIFICTION Construction: Zintec body. 3% glass-filled nylon head. Zintec end cap. Epoxy adhesives. Flow Range: 5 l/min up to 454 l/min. Mounting Threads: G 3 /4 up to G2. MOUNTING THRED Ø C /F HEX 2 PLIN RE The effect of fitting a diffuser Note: When installing a diffuser the plain area on the outside must be facing the pump inlet. The benefits of specifying a Parker Filtration Diffuser Installing a Parker Filtration Diffuser in a hydraulic reservoir is a simple operation that can make a big difference to system efficiency. With its special concentric tubes designed with discharge holes 8 opposed fluid aeration, foaming and reservoir noise are reduced and pump life extended by reducing cavitation to the pump inlet. Diffusers manufactured to customer specifications and other sizes of diffusers are available. ORDERING INFORMTION Supersedes Description mm mm Cmm Weight Kg DFI.2P DFI.4P DFI.6P DFI.9P H835-4 H835-5 Typical pressure drop at rated flow equals.35 bar. G 3 /4 Diffuser for flows up to l/min G Diffuser for flows up to 4 l/min G /2 Diffuser for flows up to 227 l/min G2 Diffuser for flows up to 454 l/min

20 Inline Filters METL INLINE FILTER SPECIFICTION Construction: Head zinc. owl luminium S47/ Element: Zintec/Stainless steel. 25 micron*. Max. flow: 9 l/min. Max working pressure: 7 bar. Thread: G. INSTLLTION DETILS Working temperature: -3 C to +8 C. Seal: Nitrile. owl tightening torque: 2 Nm. Flow direction: From outside to inside. Weight:.5 Kg. *lternative media can be specified. FILTER SELECTION Total assembly pressure drop flow curve Oil Viscosity 3 cst Relative density.856 Flow (US GPM) G CIRCUIT SYMOL 6 p (bar) MINIMUM FOR OWL REMOVL Ø OFF FIXING HOLES Ø7.2 IL Flow (l/min) ORDERING INFORMTION Flow l/min Thread Micron Replacement Rating Element 9 G 25 E.IL.5 NON-CORRODILE INLINE FILTER SPECIFICTION G Construction: Housing and bowl moulded in polyester. Element: Stainless steel mesh. 25 micron*. Max. Flow: 2 l/min. Max Working Pressure: 7 bar. Thread: G. 5 /6 2 UN 2. *For alternative media consult Parker Filtration Note: When using with water, protect from freezing. INSTLLTION DETILS Working Temperature: -3 C to +8 C. (+6 C water). Seal: Nitrile. owl Tightening Torque: 2 Nm. owl Tightening Note: box or ring spanner is recommended. Flow Direction: From outside to inside. Weight:.5 Kg. FILTER SELECTION Total assembly pressure drop flow curve Oil Viscosity 3 cst Relative density Ø45 63 Ø9 2 INLET OFF FIXING HOLES Ø p (bar) Flow (US GPM) Ø74 MINIMUM FOR OWL REMOVL ORDERING INFORMTION 6 22 /F HEX CIRCUIT SYMOL Flow (l/min) For use with Description Weight Kg Replacement Element IL.5 OIL 25 micron filter, G thread, oil IL micron filter, G 5 /6 2 UN 2, oil IL.25 WTER 25 micron filter, G thread, water IL micron filter, G 5 /6 2 UN 2, water.5.5 R.765 (oil) R.7625 (water)

21 Suction Elements Construction: Stainless steel media 3% glass filled nylon head. Zintec centre tube. Epoxy adhesives. Maximum working temperature: 9ºC. Filtration media:.4 25 micron*. Flow range: l/min. y-pass rating:.2.7 bar.. Mounting threads: G /2 up to G3. p (bar) * NON-STNDRD ELEMENTS RE VILLE TO ORDER, NPT OPTIONS VILLE. CONSULT PRKER FILTRTION SE.39 SE.32 SE.457 SE.323 Flow (US GPM) SE.324 SE.326 SE.29 SE.22 SE Flow (l/min) INSTLLTION SUCTION ELEMENTS WITHOUT YPSS C /F HEX INSTLLTION SUCTION ELEMENTS WITH YPSS C /F HEX Ø Ø MOUNTING THRED MOUNTING THRED CIRCUIT SYMOL ORDERING INFORMTION WITHOUT YPSS Note: To select filter element relate l/min directly to pump flow rating. The following range is standard, but other ratings are available. Flow Thread Micron C Weight without by-pass Supersedes l/min G SP Rating mm mm mm Kg SE.39 SE.32 SE.457 SE.323 SE.324 SE.326 SE.29 SE.22 SE.22 SE.58 SSI.D9P Note: Non-standard elements available /2 3 /4 /2 3 /4 /2 3 /4 /2 /2 /2 / /2 2 /2 3 3 ORDERING INFORMTION WITH YPSS Flow Thread Micron C Weight with by-pass Supersedes l/min G SP Rating mm mm mm Kg SE.5 SE.5 SE.52 SE.53 SE.54 SE.55 SE.56 SE.57 SSI.P SSI.2P SSI.3P SSI.C4P SSI.C5P SSI.C6P SSI.D7P SSI.D8P SSI.D9P SSI.P SSI.2P SSI.3P SSI.C4P SSI.C5P SSI.C6P SSI.D7P SSI.D8P H74-3 H74-7 H74-5 H74-9 H74-8 H74-6 H CIRCUIT SYMOL /2 3 /4 /2 /2 /2 / /2 2 / Note: To select filter element relate l/min directly to pump flow rating. The following range is standard, but other ratings are available

22 Drive Couplings INSTLLTION DETILS HU WITHDRWL CLERNCE TECHNICL DT Materials of Construction Coupling Halves Sintered Sleeves Sleeve Nylon 66 Max Temp Sleeve 83 C To select coupling model check application to establish running load condition. Check chart for factor (F) and apply factor (F) to *Rating of coupling formulae. This answer you apply to *Rating/ rev/min below. It is advisable always to check shaft sizes being used on application and check with dimension H. Factor (F) pplication Electric Motor Petrol/Diesel engine Uniform load..2 Medium shock.25.5 Heavy shock HP of application x x F *Rating of coupling= rev/min of application F G HU WITHDRWL CLERNCE ØJ ØH ØC Ø E GRU SCREW POSITION D SECTIONED DETIL ORDERING INFORMTION Ordering examples Parker Filtration Drive coupling components are ordered separately. Here are three examples of complete assemblies ordered this way.. Complete assembly DC.28.M4.4K Made up of a DC.28.M4 DC.28.4K DC.28.S (Sleeve) Complete model DC.28 drive coupling: One Gear Hub has 4mm bore with 5mm wide keyway and other hub has a /2 bore with.25 wide keyway. oth hubs supplied with locating grub screw. 2. Complete assembly DCR.42.P.P Made up of 2x DCR.42.P s DC.42.S (Sleeve) Complete model DC.42 drive coupling: oth Gear Hubs have pilot bore of.5mm. Not supplied with grub screws. 3. Complete assembly DCR.55.P.2K Made up of a DCR.55.P DC.55.2K DC.55.S (Sleeve) Complete model DC.55 drive coupling: One Gear Hub pilot bored 5 /8, the other hub pilot bored /2. Latter only supplied with grub screw. 22

23 ORDERING INFORMTION Reservoir Equipment Drive Couplings Max *Rating/ H J Speed rev/min Weight C D E F G Max Min Pilot rev/min kw hp mm mm mm mm mm mm mm ore ore ore DC.28 DC.42 DC.55 Model DC.28 DC.28.M DC.28.M DC.28.M4 DC.28.M6 DC.28.M8 DC.28.M9 DC.28.M2 DC.28.M22 DC.28.M24 DC.28.M25 DC.28.M28.mm.mm 4.mm 6.mm 8.mm 9.mm 2.mm 22.mm 24.mm 25.mm 28.mm min 38. max Coupling halves with Metric ore and Keyway Keyway Øore Width Height 3.mm 4.mm 5.mm 5.mm 6.mm 6.mm 6.mm 6.mm 8.mm 8.mm 8.mm.5mm 2.9mm 6.4mm 8.4mm 2.9mm 2.9mm 22.9mm 24.9mm 27.5mm 28.5mm 3.5mm Weight range from.267 Kg to.4 Kg Coupling halves with Imperial ore and Keyway Keyway Øore Width Height DC.42.5K DC.42.6K DC.42.7K DC.42.8K DC.42.9K DC.42.K DC.42.K DC.42.2K DC.42.3K DC.42.P 5 /8 3 /4 7 /8 /8 /4 3 /8 /2 5 /8.88 ins.88 ins.25 ins.25 ins.33 ins.33 ins.375 ins.375 ins.439 ins Coupling half pilot bored Ø ore 2mm.72 ins.84 ins.99 ins.2 ins.24 ins.37 ins.49 ins.6 ins.76 ins Weight range from.448 Kg to.753 Kg Coupling halves with Imperial ore and Keyway Keyway Øore Width Height DC.28.3K DC.28.4K DC.28.5K DC.28.6K DC.28.7K DC.28.8K DC.28.9K DCR.28.P DC.28.S Model DC.42 DC.42.M8 DC.42.M9 DC.42.M2 DC.42.M22 DC.42.M24 DC.42.M25 DC.42.M28 DC.42.M3 DC.42.M32 DC.42.M35 DC.42.M38 DC.42.M42 7 /6 /2 5 /8 3 /4 7 /8 /8 8.mm 9.mm 2.mm 22.mm 24.mm 25.mm 28.mm 3.mm 32.mm 35.mm 38.mm 42.mm.25 ins.25 ins.88 ins.88 ins.25 ins.25 ins.33 ins Coupling half pilot bored Ø ore 8mm Drive Coupling Sleeve Coupling halves with Metric ore and Keyway Keyway Øore Width Height 6.mm 6.mm 6.mm 6.mm 8.mm 8.mm 8.mm 8.mm.mm.mm.mm 2.mm.5 ins.57 ins.72 ins.84 ins.99 ins.2 ins.24 ins 2.9mm 2.9mm 22.9mm 24.9mm 27.5mm 28.5mm 3.5mm 33.5mm 35.5mm 38.5mm 4.5mm 45.5mm Weight range from.259 Kg to.4 Kg Weight range from.436 Kg to.75 Kg Height of Keyway from ase of ore METRIC IMPERIL Standard ore S 45, (985) S 96, Part, (985) Standard Keyway S 4325, Part (98) S 46, Part, (985) SSEMLY DT. Maximum angular misalignment is ±2. Maximum radial misalignment is ±.4mm. DC.42.S Model DC.55 /8 /4 3 /8 /2 5 /8 3 /4 7 /8 2 2 /8 Drive Coupling Sleeve Coupling halves with Metric ore and Keyway Keyway Øore Width Height DC.55.M25 DC.55.M28 DC.55.M3 DC.55.M32 DC.55.M35 DC.55.M38 DC.55.M42 DC.55.M55 DC.55.9K DC.55.K DC.55.K DC.55.2K DC.55.3K DC.55.4K DC.55.5K DC.55.6K DC.55.7K DCR.55.P DC.55.S 25.mm 28.mm 3.mm 32.mm 35.mm 38.mm 42.mm 55.mm 8.mm 8.mm 8.mm.mm.mm.mm 2.mm 6.mm Coupling halves with Imperial ore and Keyway Keyway Øore Width Height.33 ins.33 ins.375 ins.375 ins.439 ins.439 ins.5 ins.5 ins.626 ins Coupling half pilot bored Ø ore 6mm Drive Coupling Sleeve 28.5mm 33.5mm 33.5mm 35.5mm 38.5mm 4.5mm 45.5mm 59.5mm.24 ins.37 ins.49 ins.6 ins.76 ins.89 ins 2. ins 2.3 ins 2.3 ins 2. Ensure that the Parker Filtration Drive Coupling gear hubs are an easy fit to their respective shafts. Do not use heavy blows to force the hubs on. 3. When in position, the hubs should have a gap of 4mm as denoted by E dimension. 4. Tighten grub screws to locate both gear hubs on to their respective shafts. Weight range from.248 Kg to.932 Kg Weight range from.248 Kg 2.46 Kg 23

24 Multiclamp SPECIFICTION When only the best Clamping System will do...specify Multiclamp Multiclamp is a system. system of components, each one engineered to a high standard that together build to provide effective, all-purpose pipework clamping. Multiclamp offers creative and cost-effective environmental benefits to the system designer and installer. Creating accurate runs of varying diameter tubes, pipes, hoses and cables in all industries. Secure Multiclamp installations ensure a leak free, noise free and vibration free system. The neat design of pipe line runs offers easy maintenance of machinery and plant equipment. Visual planning of lines runs is straightforward with Multiclamp accurate installations can be achieved without skilled labour keeping costs down and quality up. Single and double clamping units are ordered in sets only. i.e. set of clamping units = pairs. Multiclamp is not ordered in set. i.e. -off clamping unit = upper and lower clamping unit. Single Clamp Double Clamp C CTS ( ) Ø C C SERIES PT.7557 E F REF F E D Multiclamp 6 holes Split ushes set of clamping units = pair Split bushes are ordered in sets only i.e. set of bushes = bushes of one size C THETFORD ENGLND SERIES PT.7557 Ø PIPE SIZE H REF G Ø D E F MTERIL SPECIFICTIONS Zinc plated steel with anti-corrosive, full passivate. Multiclamp can also be multi-stacked using stacking studs and nuts. Series and 6 clamp is supplied in lengths of 63mm and Series 32 in lengths of 26mm. These can be simply cut to the required lengths for installation. Series will accept pipe or hose diameters from 6mm up to 2mm maximum. Series 6 from 6mm up to 28mm and Series 32 from mm up to 5mm. cross the 3 Series, there are 26 different high-quality split rubber bushes to select from to cope with any combination and number of different pipe and hose diameters in the same run. 24

25 Multiclamp Components Fixing Methods Stacking Stud The STCKING STUD can be threaded into a tapped hole in the mounting base or plate, then the STCKING NUT is tightened down securely with a spanner. Clamping Unit dual purpose unit which provides both halves of a complete clamp. Supplied in various sizes which provides for easy installation or removal of tube fittings using conventional methods. This simple component forms the basis of the Multiclamp system. Stacking Nut Used in conjunction with STCKING STUD for continuous stacking of CLMPING UNITS. This holds two units firmly together in suspension and secures the lower unit to a base column or support. The STCKING NUT and STCKING STUD maintains correct alignment as each Multiclamp is progressively stacked. It is simply fixed and allows for the upper unit to be securely fastened in place by a standard bolt. Weld Plate When Multiclamp is required to be secured by welding, insert standard bolt into WELD PLTE. Hexagon head of Standard olt is retained in hexagonal recess on underside of WELD PLTE, leaving a flush surface for mounting. Secure to lower clamping unit with STCKING NUT (finger tight). Repeat for each welding position. ssemble lower clamping unit to mounting surface by welding each WELD PLTE and finally tighten each STCKING NUT before proceeding with remainder of installation. Split ushing Made from an ethylene propylene copolymer (EPDM). The bushes exhibit excellent capability to absorb vibrationary loads applied by retained pipework and reduced noise transmission from pipework to surrounding metal supports etc. The bushes have good mechanical properties and are highly resistant to ozone weathering and a wide range of chemicals. They offer a good electrical insulation and are suitable for use over a wide temperature range. Note that if bushes are required for immersion in mineral oils, an alternative material is recommended. Mounting daptor metal bushing that fits into the line opening of the clamping unit. Similar to a split bushing, this component accommodates standard attaching bolts when making a suspended mount of a plate or column. bridgetype mount can be formed by using one adaptor on each end of a Multiclamp. The adaptors are available in sizes to suit all Series clamping units. Mounting daptor Stacking Stud and Nut When mounting plate has a thickness of 9.5mm (3/8 ) or less, STCKING STUD should be screwed into STCKING NUT and stud passed through drilled hole and secured with a retaining nut. MULTICLMP can be secured and suspended from a column or mounting plate by using MOUNTING DPTORS and standard attaching bolts. dditional MULTICLMPS can also be stacked on to the mounted clamp. 25

26 Multiclamp PLNNING WITH MULTICLMP Planning with Multiclamp These notes have been compiled to assist in planning your Multiclamp system. Multiclamp offers considerable flexibility. For example, it can fit in with a factory installation that is being built in phases. Should a last minute change in pipe diameter occur during installation, an alternative rubber bush is likely to be all that is required. Not a complete and expensive re-think of the installation. Multiclamp metal components can be sprayed to match a vehicle livery or plant installation and, if installed properly, should require no maintenance. Installation is simple and requires no experience nyone can use Multiclamp and only the basic, everyday tools are required. From one pipe to almost any number because each Multiclamp position can be visually sighted and its position adjusted an almost guaranteed straight run can be obtained. Equally, changes of plane or direction can be achieved simply and securely. Group pipe sizes together to obtain the most economical use of three basic Multiclamp Series. Some sites will require all pipes mounted in one single plane either vertical or horizontal. When stacked modules are preferred, the only work to be done on the Multiclamp is to saw off the desired length. If a large number of pipe lines are to be run, it is recommended that the upper clamping unit is simply cut into two lines only, and progressively assembled by securing two pipes at a time. It will be recognised that most odd lengths on site will be used, and one man can easily cope with a large number of pipe lines by this simple progressive build up. This assembly will provide easy access for servicing and replacing pipes. This method also reduces the quantity of Stacking Nuts and Studs by 5%. If a factory installation is being built in phases, it would be wise to leave the first phase with a lower clamping unit and Stacking Nuts in position ready to receive pipe runs for the next building phase. Series 6.mm-2.mm ( /4-3 /4 ) Series 6 6.mm-28.mm ( /4 - ) Stacked modules or single module Series 32.mm-5.mm ( 3 /8-2 ) Fixing points to suit Your maximum pipe size will determine the series to use. There is a degree of versatility provided by the rubber bushes. You choose from single or multistacked Multiclamp, whichever suits your particular installation requirements. Stacking stud and nut not required in this position Clamp in position for phase 2 Phase Just consider the savings when Multiclamp is planned really wisely. How far apart should Multiclamp be spaced? 26

27 ORDERING INFORMTION SERIES O Stacking Nuts (5 per part number) Thread Weight:.8 Kg (per set) Weld Plates ( per part number) C D E F Weight:.35 Kg (per set) MC.N..mm 33.mm M8-.25 MC.WP. 3.3mm 25.mm.mm 6.3mm 25.mm 8.5mm Stacking Studs (5 per part number) C Thread Weight:.48 Kg (per set) Standard olts (5 per part number) MC.S. 32.mm 2.mm 4.5mm M8-.25 MC.S. Series Thread Length M mm Reservoir Equipment Multiclamp Mounting daptors ( piece per part number) Ø Weight:.2 Kg (per set) MC...MO 27.mm 25.mm 8.7mm ORDERING INFORMTION SERIES 6 Stacking Nuts (5 per part number) Thread Weight:.6 Kg (per set) Weld Plates ( per part number) C D E F Weight:.35 Kg (per set) MC.N.6.mm 44.mm M8-.25 MC.WP. 3.3mm 25.mm.mm 6.3mm 25.mm 8.5mm 3.mm 7.5mm Thread M-.5 Weight:.99 Kg (per set) Stacking Studs (5 per part number) C Thread Weight:.2 Kg (per set) Standard olts (5 per part number) MC.S. 32.mm 2.mm 2.mm M8-.25 MC.S. Series Thread Length 6 M mm ORDERING INFORMTION SERIES 32 Stacking Nuts (5 per part number) Weld Plates ( per part number) C D E F Weight:.7 Kg (per set) MC.N.32 MC.WP mm 32.mm 2.mm 8.mm 32.mm.mm Stacking Studs (5 per part number) 38.mm 22.mm C 2.mm Thread M-.5 Weight:.9 Kg (per set) Standard olts (5 per part number) MC.S.32 MC.S.32 Series Thread Length 32 M-.5 3.mm Mounting daptors ( single piece per part number) Ø Weight:.6 Kg (per set) Ø Weight:.26 Kg (per set) MC..6.MO 27.mm 36.mm 8.7mm Mounting daptors ( single piece per part number) MC..32.MO 4.mm 58.mm.7mm 27

28 Multiclamp SPECIFICTION Typical Single Clamp with exploded view Typical Double Clamp with exploded view 2. Upper and Lower Clamping Unit 2. Various sizes of Split ushings Multiclamp 6 holes Split ushes Stacking Nut 5. Weld Plate 3. Stacking Stud 6. Standard olt THRED Stacking Nuts Stacking nuts are ordered in sets only. i.e. set of stacking nuts = 5 stacking nuts of one size. Ø Mounting daptors Mounting adaptors are not ordered in sets. i.e. off mounting adaptors = single piece. Stacking Studs Stacking studs are ordered in sets only. i.e. set of stacking studs = 5 stacking studs of one size. THRED Weld Plates Weld plates are ordered in sets only. i.e. set of weld plates = weld plates. F C D E 28

29 Multiclamp ORDERING INFORMTION SERIES O ( 6mm-2mm pipe dia.) Single Clamp ( pairs per part number) Double Clamp ( pairs per part number) Multiclamp ( pair per part number) Split ushes ( pairs per part number) MC.. 25.mm 8.5mm C 38.mm D 55.mm E 9.mm F 38.mm Ø 9.mm Weight:.6 Kg (per set) MC mm 8.5mm C 38.mm D 93.mm E 9.mm F 38.mm Ø 9.mm Weight:. Kg (per set) MC mm 38.mm C 25.mm D 5.mm E 38.mm F 6.5mm G 9.mm H 38.mm Ø 9.mm Weight:.8 Kg (per pair) Pipe Size mm O/D N 25.5mm 27.mm 34.mm 6 /4 8 5 /6 3 /8 2-4 /2 / /8 3 / /4 Quoted weights based on a pack of Part No. Weight Weight MC.G..4 MC.G..5 MC.G..6 MC.G..8 MC.G...3 Kg.3 Kg.2 Kg.2 Kg. Kg MC.G..2.9 Kg ORDERING INFORMTION SERIES 6 ( 6mm-28mm pipe dia.) Single Clamp ( pairs per part number) Double Clamp ( pairs per part number) Multiclamp 2 holes ( pair per part number) Split ushes ( per part number) MC mm 7.mm C 5.8mm D 65.mm E 23.8mm F 47.6mm Ø 9.mm Weight:.8 Kg (per set) MC mm 7.mm C 5.8mm D 6.mm E 23.8mm F 47.6mm Ø 9.mm Weight:.6 Kg (per set) MC mm 5.8mm C 25.mm D 2.mm E 5.8mm F 68.8mm G 25.mm H 5.mm Ø 9.mm Weight:. Kg (per set) Pipe Size mm O/D N 35.4mm 27.mm 34.mm 6 /4 8 5 /6 3 /8 2-4 /2 / /8 3 / / /8 / /4 28 MC.G.6.4 Part No. Weight Weight MC.G.6.4 MC.G.6.5 MC.G.6.6 MC.G.6.8 MC.G.6. MC.G.6.2 MC.G.6.4 MC.G Kg.28 Kg.28 Kg.26 Kg.22 Kg.2 Kg.8 Kg.4 Kg MC.G Kg Dimension is 38.mm ORDERING INFORMTION SERIES 32 ( mm-5mm pipe dia.) Single Clamp ( pairs per part number) Double Clamp ( pairs per part number) Multiclamp 6 holes ( pair per part number) Split ushes ( per part number) MC mm 9.4mm C 76.2mm D 95.mm E 38.mm F 76.2mm Ø.mm Weight: 2.25 Kg (per set) MC mm 9.4mm C 76.2mm D 7.mm E 38.mm F 76.2mm Ø.mm Weight: 3.82 Kg (per set) MC mm 76.2mm C 4.mm D 34.mm E 76.2mm F 2.mm G 38.5mm H 77.mm Ø.mm Weight: 3.8 Kg (per pair) Pipe Size mm O/D N 59.mm 44.5mm 3 /8 2-4 /2 / /8 3 / / /8 / / / / /2 42 /4 5 2 /2 Part No. MC.G.32.6 MC.G.32.8 MC.G.32. MC.G.32.2 MC.G.32.4 MC.G.32.6 MC.G.32.8 MC.G.32.2 MC.G MC.G MC.G Weight.3 Kg.2 Kg. Kg. Kg. Kg. Kg. Kg.8 Kg.8 Kg.6 Kg.4 Kg 29

30 Speed Control and Needle Valves SPECIFICTION Construction: rass 58 UNI 575 (G 3 /4 modelsteel) Nickel plated. Max. working pressure: 2 bar. Operating temp. range: -2 C to + C. Fluid compatibility: Petroleum-based oils. Sizes: G /4, G 3 /8, G /2 and G 3 /4. Speed control valve/check valve crack pressure:.5 bar. Panel mounting: retaining nut for panel mounting is included with every option. Filtration recommendation: Parker Filtration 25 micron absolute system filtration is desirable to ensure acceptable reliability and service life. G /4, G 3 /8 and G /2 options ØC G 3 /4 option Ø47. PNEL MOUNTING THRED G PNEL MOUNTING THRED M4 x.5 D F MX E PORT IDENTIFICTION ORDERING INFORMTION Speed Control Valves white caps C D E F G Weight Description mm mm mm mm mm Size Panel mtg thread Kg SCV.7 G /4, 2 bar speed control M7 x.3 SCV.7 G 3 /8, 2 bar speed control M2 x.24 SCV.72 G /2, 2 bar speed control M25 x.5.45 SCV.73 G 3 /4, 2 bar speed control M4 x.5.3 Needle Valves orange caps C D E F G Weight Description mm mm mm mm mm Size Panel mtg thread Kg 2 G /4, 2 bar needle valve M7 x.3 2 G 3 /8, 2 bar needle valve M2 x G /2, 2 bar needle valve M25 x G 3 /4, 2 bar needle valve 5 73 M4 x

31 Speed Control and Needle Valves TECHNICL DT PRESSURE DROP ( P) FLOW CHRCTERISTICS WITH MINERL OIL T 3 cst VISCOSITY Graphs for needle/shut-off valves and speed control valves with flow - (controlled flow through needle). Flow setting by number of turns of control knob is indicated on the body graduated scale. Graphs for speed control valves. Flow - (flow through check valve), with needle valve portion in fully open and fully closed positions. 2/SCV.7 Flow setting in no. of turns Flow (US GPM) 22/SCV.72 Flow setting in no. of turns Flow (US GPM) SYMOL p (bar) FULLY OPEN Flow (l/min) SCV.7 Flow setting (fully closed/fully open) Flow (US GPM) p (bar) FULLY OPEN Flow (l/min) SCV.72 Flow setting (fully closed/fully open) Flow (US GPM) p (bar) CLOSED 2 74 OPEN Flow (l/min) p (bar) CLOSED OPEN Flow (l/min) 2/SCV.7 Flow setting in no. of turns Flow (US GPM) 23/SCV.73 Flow setting in no. of turns Flow (US GPM) p (bar) FULLY OPEN Flow (l/min) SCV.7 Flow setting (fully closed/fully open) Flow (US GPM) p (bar) FULLY OPEN Flow (l/min) SCV.73 Flow setting (fully closed/fully open) Flow (US GPM) p (bar) CLOSED OPEN Flow (l/min) p (bar) CLOSED OPEN Flow (l/min) 22

32 Inline Check Valves INSTLLTION DETILS SPECIFICTION Construction: Steel UNI 55. all and spring: Chrome finished steel. Retainer: Nylon. Flow rates: From 2 l/min to 5 l/min. Max. working pressure: 35 bar. Valve crack pressures:.35 and 4.5 bar. /F HEX CIRCUIT SYMOL TECHNICL DT Pressure Drop Flow Curves p (bar) Flow (US GPM) Flow (l/min) THRED ORDERING INFORMTION Cracking Flow Pressure Thread Weight l/min bar G mm mm Kg /4 3 /8 /2 3 /4 /4 3 /8 /2 3 /

33 Gauge Isolator Valves SPECIFICTION Construction: Single Station: Cast iron and steel. Knurled aluminium knob with Twist to lock or push to read type. Max. working pressure: 35 bar. Port size: Single Station: G /4. Weight: Single Station:.9 Kg. SINGLE STTION INSTLLTION DETILS HEX NUT 38. /F 3. G G /4 TYP 3 POSITIONS DR P CIRCUIT SYMOL 2. SQ OPERTION DETILS Single Station ORDERING INFORMTION GI.486 GI.44 Description Single station gauge isolator Twist to lock type Single station gauge isolator Push to read type Weight.9 Kg.9 Kg 223

34 63mm Dia. Pressure Gauges SPECIFICTION Construction: Case: Natural finish stainless steel. Window: Non-splintering clear acrylic glass. Movement: Cu alloy. Dial: White plastic, with pointer stop pin. Pointer: lack plastic. Liquid filling: Glycerine 99.7%. Working pressure: Max 75% of the full scale value. Process temperature: + 6 C maximum. ccuracy:.6% FSD. Wetted parts connector: Copper alloy. ourdon tube: < 6 bar = Cu alloy, C-type, soft soldered. > 6 bar = Cu alloy, helical type, soft soldered. Mounting Stem Detail SNUER FITTED G /4 ( /4 SP) 4 /F HEX Note: It is recommended that all glycerine gauges should be mounted in the vertical position with gauge case relief valve uppermost. Pressure range up to bar available. INSTLLTION DETILS ottom connection h (mm) a b D D2 e G h SW Weight ±.5 ± Kg G / (mm) ottom Connection Panel Mounting (Centre ack) b b2 D D2 e G SW Weight ±.5 ± Kg G /4 4.2 Note : Panel cut-out 64.5 ±.5 Note 2: 3mm on the outside radius required to allow for fixing clamp. Panel Mounted (3-hole flange) 2 D G SW ØD2 ØD ØD3 2 a Ø5 b e Ø9.5 ØD2 Panel Mounting (Centre ack) D SYMOL G SW Note : Gauge dimensions as for Panel Mounting option above with flange as shown below. Note 2: Panel cut-out for 3-hole mounting 67±.3. (mm) b2 D D2 D b e ØD2 ORDERING INFORMTION ottom connection Description Supersedes PG.63.4 PG.63. PG.63.6 PG PG.63.4 PG.63.6 PG.63. PG.63.6 PG PG.63.4 PG.63.6 Panel Mounting Description Supersedes PGC.63. PGC.63.6 PGC PGC.63.4 PGC.63.6 PGC.63. PGC.63.6 PGC PGC.63.4 PGC.63.6 Description Supersedes Weight Kg PGF.63. PGF.63.6 PGF PGF.63.4 PGF.63.6 PGF.63. PGF.63.6 PGF PGF.63.4 PGF bar - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar Panel Mounted (3-hole flange) - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar PG.4569 PG.456 PG.4562 PG.4564 PG.4565 PG.4567 PG.4568 PG.4562 PG PG PG.459 PG.45 PG.452 PG.454 PG.455 PG.457 PG.458 PG.452 PG.4522 PG.4523 PG.4539 PG.453 PG.4532 PG.4534 PG.4535 PG.4537 PG.4538 PG.4532 PG PG *Note: ny subsequent changes to gauge accuracy will be notified. 224

35 mm Dia. Pressure Gauges SPECIFICTION Construction: Case: S 34 S5 stainless steel. Window: crylic. Movement: rass. Dial: White aluminium. Pointer: lack aluminium. Liquid filling: Glycerine 98%. Working pressure: Full scale value. f Process temperature: + 6 C maximum. ccuracy:.% FSD. Wetted parts connector: Copper alloy. ourdon tube: < bar = Cu alloy, c-type, soft soldered. > bar = stainless steel.457, helical type, brazed. Mounting Stem Detail Note: It is recommended that all glycerine gauges should be mounted in the vertical position with gauge case relief valve uppermost. INSTLLTION DETILS ottom connection h (mm) a b D D2 e G h SW Weight ±.5 ± Kg G / (mm) ottom Connection Panel Mounting (Lower ack) b b2 D D2 e G SW Weight ±.5 ± Kg G / Note : Panel cut-out 2 ±. Note 2: 3mm on the outside radius required to allow for fixing clamp. Panel Mounted (3-hole flange) 2 D G SW ØD2 ØD ØD3 Ø6 a Ø7.5 SNUER FITTED G /2 ( /2 SP) 22 /F HEX b e ØD2 Panel Mounting (Lower ack) D SYMOL G (mm) SW Note : Gauge dimensions as for Panel Mounting option above with flange as shown below. Note 2: Panel cut-out for 3-hole mounting 4±.5. b2 D D2 D b e ØD2 ORDERING INFORMTION ottom connection Description Supersedes PG.. PG..6 PG..25 PG..4 PG..6 PG.. PG..6 PG..25 PG..4 PG..6 PG.. Panel Mounting Description Supersedes PGE.. PGE..6 PGE..25 PGE..4 PGE..6 PGE.. PGE..6 PGE..25 PGE..4 PGE..6 PGE.. Description Supersedes Weight Kg PGF.. PGF..6 PGF..25 PGF..4 PGF..6 PGF.. PGF..6 PGF..25 PGF..4 PGF..6 PGF.. - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar - bar - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar - bar Panel Mounted (3-hole flange) - bar -6 bar -25 bar -4 bar -6 bar - bar -6 bar -25 bar -4 bar -6 bar - bar PG.4869 PG.486 PG.4862 PG.4864 PG.4865 PG.4867 PG.4868 PG.4862 PG PG PG PG.489 PG.48 PG.482 PG.484 PG.485 PG.487 PG.488 PG.482 PG.4822 PG.4823 PG.4825 PG.4839 PG.483 PG.4832 PG.4834 PG.4835 PG.4837 PG.4838 PG.4832 PG PG PG *Note: ny subsequent changes to gauge accuracy will be notified. 225

36 O Ring Kits SPECIFICTION Material: Nitrile rubber, 7 I.H.R.D. Temp. range: -4 C to +2 C. Compatibility: Mineral based oils and greases. ll sizes suitable for dynamic and static applications. Weight: Complete kit.7 Kg. ll sizes conform to S 86, ISO 67, ISO 68 and SE S 568. Individual sizes of O Ring available in s. TECHNICL DT Metric Section 2.mm 2.5mm 3.mm 3.5mm Imperial Section.78mm 2.62mm 3.53mm INSTLLTION DETILS Note: Content explanation (see below) 8 x 3 x 2 = Quantity x Internal Ø x Section Ø Ø INTERNL 5.34mm The above measurements refer to section mm given in Ordering Information. ORDERING INFORMTION Contents of Metric O Ring Kit x 8 x 8 x 3 x 2 4 x 2 5 x 2 4 x 4 x x 2 x x 6 x x 7 x x 9 x 38 x 3 38 x 4 2 x 2 x 36 x 3 35 x 3 2 x 2 x 2 x 2 x 3 22 x 3 24 x 3 Contents of Imperial O Ring Kit 29 2 x 2.9 x.78 RP/S 6 3 x 3.95 x 2.62 RP/S 3 3 x 5.54 x 2.62 RP/S 4 x x 3.53 RP/S 222 x 36. x 3.53 RP/S 22 x 2.22 x 3.53 RP/S 2 2 x 3.68 x.78 RP/S 7 3 x 2.3 x 2.62 RP/S 2 x x 3.53 RP/S 22 x 2.82 x 3.53 RP/S 22 2 x 4.48 x.78 RP/S 8 3 x 7.3 x 2.62 RP/S 5 7 x x 5.33 RP/S 325 x 23.4 x 3.53 RP/S 23 4 x x x 33 x 3 3 x.78 x 2.62 RP/S x x 3.53 RP/S 29 8 x 6 x 2 9 x x 42 x 4 2 x 25 x 3 4 x 2 x 5.28 x.78 RP/S 9 3 x 8.72 x 2.62 RP/S 6 7 x 4.65 x 5.33 RP/S 326 x x 3.53 RP/S 24 7 x 7 x 2 4 x x x 32 x 3 2 x 27 x 3 3 x 9.9 x 2.62 RP/S 2 x 6.7 x.78 RP/S x 3.34 x 3.53 RP/S 28 x x 3.53 RP/S 25 7 x 8 x 2 7 x x 2 2 x 9 x 3 9 x 45 x 4 2 x 3 x 3 2 x 28 x 3 SECTION 2 x 7.66 x.78 RP/S 2 x 9.25 x.78 RP/S 2 x 8.64 x 3.53 RP/S 2 7 x x 5.33 RP/S 327 x x 3.53 RP/S 27 x 28.7 x 3.53 RP/S