Glass-Filled Nylon and Metal Breathers IP65 Rated, Metal, Screw-on and Lockables

Transcription

1 Glass-Filled Nylon and Metal Breathers IP65 Rated, Metal, Screw-on and Lockables 83 Reservoir equipment

2 IP65 Rated Filler Breathers Specification for Single and 6Hole Installation Option Construction: Moulded in non-corrodible glass-filled nylon combining strength with alightweight design. Options: () single (63mm dia) hole Filler breather installation that eliminates drilled and tapped holes using self-locking clamps. (2) 6hole Filler Breather Installation that uses 6xNo thread forming screws. (3) 3hole filler breather utilises 3xzinc and clear chromate plated steel screws. Option Filler Breathers (Single Hole Installation) Strainers: Unique design diffuses oil flow into the reservoir. () Single length in polypropylene (95mm length) (2) 2-piece telescopic in polypropylene (95mm length max.) Filtration element: Expanded polyurethane foam, micron nominal. Seals: Nitrile. Working temperature: -30 C to +90 C. Pressurised filler breathers: vailable in 3pressure options tomaintain apositive pressure inareservoir. Pressurisation options: 0.2, 0.35 and 0.7 bar crack pressure. Pressurisation valve: Nylon/Nitrile. Dipstick: vailable for use with options and 2. Dipsticks are available in 2lengths and in packs of. Dipstick material: BS. Hi/Lo indicators: cetal. djustable Red/Green level indicators. Dipstick lengths: 200mm and 400mm. Breather weight: 0.2Kg. nti-splash feature: The unique design antisplash feature isstandard on all options and 2and allows for adipstick to be fitted if required max Ø B98XXX Pressurised Pressure Drop Curves Valve Valve Valve Δ p(psid) Ø Flow I/sec (ir) B98XXX Non-Pressurised Pressure Drop Curves Ø With nti-splash.5 Δ p(psid) Option. Single Hole Filler Breathers Pressurised B98220 B98230 B B B B B B98270 B Supersedes B UC B UC B UC B UC B UC B UC B UC B UC B UC Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Description µ nom Pressurised 0.2bar with 95mm strainer Pressurised 0.35bar with 95mm strainer Pressurised 0.2bar without strainer Pressurised 0.2bar with telescopic strainer Pressurised 0.35bar without strainer Pressurised 0.35bar with telescopic strainer Pressurised 0.7bar without strainer Pressurised 0.7bar with 95mm strainer Pressurised 0.7bar with telescopic strainer 0.05 Without nti-splash Flow I/sec (ir) Option. Single Hole Filler Breathers Non-Pressurised B9820 B98202 B98200 Supersedes B.9820.UC B UC B UC Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Description µ nom Filler breather with 95mm strainer Filler breather with telescopic strainer Filler breather without strainer 84 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 25

3 Filler Breathers (6 Hole Installation) Option 2 Note.Un-pressurised 6hole fixing: Form 6 off tank mounting holes between Ø4.0 and 4.4mm (dependent on the material and thickness see guide below) equispaced on 70-73mm P.C.D. to suit supplied No. thread forming screws. Note 2. Pressurised 6-hole fixing: Form 6 off tank mounting holes between Ø4.0 and Ø4.4mm (dependent on the material and thickness see guide below) equispaced on 73mm P.C.D. to suit supplied No. thread forming screws. Ø Note 3. Reservoir mounting guide Sheetthickness mm Hole size mm Ø 27 Telescopic Strainer The telescopic strainer design is ideal, where reservoir depth allows, to increase the surface area of the strainer, improving still further its straining ability, oil flow-through and allowing for longer dipstick lengths Ø3 Ø42 Option 2. 6 Hole Filler Breathers Pressurised B98870 B B98820 B B B98830 B B B Supersedes B UC B UC B UC B UC B UC B UC B UC B UC B UC Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Description µ nom Pressurised 0.7bar with 95mm strainer Pressurised 0.2bar without strainer Pressurised 0.2bar with 95mm strainer Pressurised 0.2bar with telescopic strainer Pressurised 0.35bar without strainer Pressurised 0.35bar with 95mm strainer Pressurised 0.35bar with telescopic strainer Pressurised 0.7bar without strainer Pressurised 0.7bar with telescopic strainer Ø42 Option 2. 6 Hole Filler Breathers Non-Pressurised B98800 B9880 B98802 Supersedes B UC B.9880.UC B UC Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Description µ nom Filler breather without strainer Filler breather with 95mm strainer Filler breather with telescopic strainer 85 6x Ø Reservoir equipment

4 Filler Breathers Option 3 Filler Breathers (3 Hole Installation) Ø50.5 Ø53 New Options Fully Tested s part of the design development programme for the new IP65 Filler Breathers, extensive performance and endurance testing was carried out to ensure durability and efficiency. Ø24 3x Ø hole Filler Breathers (6-hole available) B68 B688 Description µ nom Filler breather without strainer Filler breather with 95mm strainer Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Note 3: Not suitable for use with B.68206/207 Note 4:6-hole B.689/B.6898 option available. Note: Form 3off tank mounting holes between Ø4.0 and Ø4.4mm (dependent on the material and thickness see chart for guide) equispaced on 4.3 P.C.D. to suit No. thread forming screws supplied. Dipstick Options Dipstick Ordering B68206 B68207 Supersedes DIP.206 DIP.207 Description x200mm Dipsticks x400mm Dipsticks Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Dipsticks The dipstick, available in 2lengths 200mm and 400mm, can be cut to the required length or left as it is and the Hi/Lo indicators moved and positioned on the dipstick itself by squeezing the sides of the indicator and repositioning along the dipstick. 86 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 25

5 Screw-On Type ir Breathers Standard Screw-On Breathers -Specification Option G / 2 and G 3 / 4 (Ø) Pressure Drop Flow Curve Construction: Moulded in non-corrodible glass-filled nylon combining strength with alightweight design. Option : 2screw on type air breathers are available G / 2 or G 3 / 4 threaded base models. Filtration element: Expanded polyurethane foam, micron nominal. Seals: Nitrile. Working temperature: -30 C to +90 C. Pressurised air breathers: vailable in 3pressure options to maintain a positive pressure inareservoir. Pressurisation options: 0.2, 0.35 and 0.7 bar crack pressure. Pressurisation valve: Nylon/Nitrile. Dipstick: vailable for use with all options. Dipsticks are available in 2lengths and in packs of. Dipstick material: BS. Hi/Lo indicators: cetal. djustable red/green level indicators. Dipstick lengths: 200mm and 400mm. Breather weight: 0.2Kg. nti-splash feature: The unique design anti-splash feature is standard on option and allows for a dipstick to be fitted if required. B98XXX Screw-on Non-Pressurised Pressure Drop Curves G / 2 Ø Δ p(bar) With nti-splash Δ p(psid) Without nti-splash Flow I/sec (ir) 3 G / 2 30 /F HEX Note: For pressure drop information on the Option. Pressurised consult Parker Filtration. Option G / 2 or G 3 / 4 B986 B9862 B9863 B9867 B984 B9842 B9843 B9847 Supersedes B.986.UC B.9862.UC B.9863.UC B.9867.UC B.984.UC B.9842.UC B.9843.UC B.9847.UC Description µ nom G / 2 Un-pressurised G / 2 pressurised 0.2 bar G / 2 pressurised 0.35 bar G / 2 pressurised 0.7 bar G 3 / 4 Un-pressurised G 3 / 4 pressurised 0.2 bar G 3 / 4 pressurised 0.35 bar G 3 / 4 pressurised 0.7 bar Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. G 3 / 4 Ø 6 96 G 3 / 4 30 /F HEX 87 Reservoir equipment

6 Screw-On Type ir Breathers Compact Screw-On Breathers -Specification Option 2 G / 4,G 3 / 8,R / 2 and R 3 / 4 (Ø40) Construction: G / 4,G 3 / 8,R / 2 and R 3 / 4 cap and base plate mouldings in nylon 66. Element: Expanded Polyurethane foam, micron nominal. Dipstick: vailable for use with R / 2 and R 3 / 4. Dipstick material: BS. Hi/Lo indicators: cetal adjustable red/green level indicators. Dipstick lengths: 200mm and 400mm (packs of ). Breather weights: 0.028Kg Pressure Drop Flow Curve Ordering Information Δ p(bar) G / Flow I/sec (ir) Δ p(psid) Option 2 G / 4,G 3 / 8,R / 2 and R 3 / 4 (Packs of only) B683 B68X B68Y B68Z Supersedes B.683.UC B.68X.UC B.68Y.UC B.68Z.UC Description µ nom G / 4 Un-pressurised G 3 / 8 Un-pressurised R / 2 Un-pressurised R 3 / 4 Un-pressurised Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Note: For pressure drop information on G 3 / 8,R / 2 and R 3 / 4,consult Parker Filtration. Ø40 G / 4 Ø40 G 3 / 8 20 /F HEX G / 4 Ø R / 2 Ø40 R 3 / /F HEX G 3 / /F HEX /F HEX 9 4 R / 2 R 3 / 4 88 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 25

7 Screw-On Type ir Breathers -Specification Option 3 G 3 / 8,G / 2 and G 3 / 4 (Ø70) Construction: Mouldings in glass-filled nylon and glass coupled polypropylene. Element: Expanded Polyurethane foam, micron nominal. Seals: Nitrile. Pressurised air breathers: vailable G 3 / 8,G / 2 and G 3 / 4, 3pressure options to maintain apositive pressure in areservoir. Pressurisation options: 0.2, 0.35 and 0.7 bar crack pressure. Pressure Drop Flow Curve Pressurisation valve: Nylon. Dipstick: vailable for use with G 3 / 8,G / 2 and G 3 / 4. Dipstick material: Mini-series in brass. Hi/Lo indicators: cetal adjustable red/green level indicators. Dipstick lengths: 200mm and 400mm (packs of ). Breather weights: 0.075Kg, Mini-series 0.09Kg. Ordering Information Δ p(bar) G 3 / 8 G / 2 G 3 /4 Option 3 G 3 / 8,G / 2 and G 3 / 4 B685 B687 B686 Supersedes SB.5 SB.7 SB.6 Description µ nom G 3 / 8 Un-pressurised G 3 / 4 Un-pressurised G / 2 Un-pressurised Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability Flow I/sec (ir) Ø70 G 3 / 8 G / 2 Ø70 The mini-series breather Screw-on option Push-fit option Ø G 3 / 8 28 /F HEX G / 2 28 /F HEX Ø70 G 3 / min Ø22 Spotface Ø Ø Ø.8 G / Ø3.55 Ø S Description Gearbox air breather G 3 / 4 3 /F HEX 89 Reservoir equipment

8 Filler Breathers (Metal) Metal irbreather/filler breather Specification Ø76.2 Locking lug option (556) For added security, certain Parker Filtration Metal Filler Breather Filters can be specified with alocking lug option. Ø49.5 Ø83 Ordering Information Standard products table Supersedes Replacement cap Supersedes Displacement I/min Crack pressure Micron rating ir flow m 3 /min Thread Weight SB562 SB563 B63 B PB7305 PB730 SP735 SP73 SB.562. SB.563. B.63. B.380. PB PB SP SP.73.. CP.63 CP.380 CP.7305 CP.730 Threaded airbreather (unpressurised) Filler breather -filter flange type (unpressurised) 430 Filler breather -filter flange type (pressurised) CP bar CP bar ir breather -threaded type (pressurised) Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. CP.63. CP bar 0.70 bar µ nom µ nom µ nom µ nom µ nom µ nom µ nom µ nom µ nom G 3 / 4 G / 4 G 3 / 4 G 3 / kg 0.06kg 0.24kg 0.08kg 0.24kg 0.27kg 0.27kg 0.20kg 0.20kg 90 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 26

9 73 -Threaded type (Pressurised) Ø76.2 Displacement: 430 l/min. Micron rating: µ nominal Weight: 0.2 Kg. Thread: G 3 / ir flow: 0.45m 3 /min. Valve crack-pressure: 0.35 and 0.7 bar. 6 G 3 / 4 35 /F HEX Threaded type (Un-pressurised) Ø44.5 Displacement: 562 =430 l/min. 563 =35 l/min. Micron rating: µ nominal ir flow: 562 =0.45m 3 /min. 563 =0.5m 3 /min. Weight: 562 =0.20 Kg. 563 =0.06 Kg. Thread: 562 =G 3 / =G / G / 4 /G 3 / /F HEX 380 -Filter flange type Ø44.5 Displacement: 35 l/min. Micron rating: µ nominal ir flow: 0.5m 3 /min. Weight: 0.08 Kg Ø5 Tank installation notes. Un-pressurised 6hole fixing Form off tank mounting holes between Ø4.0 and Ø4.4 (dependant on the material and thickness, consult Parker Filtration) equispaced on P.C.D. to suit No. thread forming screws supplied. 2. Pressurised 6hole fixing Form 6off mounting holes between Ø4.0 and Ø4.4 equispaced on 73.0 P.C.D. to suit No. thread forming screws supplied. 3. Un-pressurised 3hole fixing Form 3off tank mounting holes between Ø4.0 and Ø4.4 equispaced on 4.3 P.C.D. to suit No. thread forming screws supplied. Breather Units Ordering Information Small Breather Specification Ø35 H H H Supersedes H H H Description Small breather / 4 BSPT thread Small breather 3 / 8 BSPT thread Small breather / 2 BSPT thread 22 Three size: / 4 BSPT 3 / 8 BSPT / 2 BSPT 5 9 Reservoir equipment

10 Lockable Filler Breather Installation Details Tank Mounting 5.5 Ø5 Strainer 7 3off equispaced clamps Ø Tank mounting hole Flap to protect lock Stand Pipe Mounting 2 locking screws threaded type at positions Xand Y 3 locking screws push on type at positions X, Yand Z X 50.5 Z 34 7 B Y Lockable Filler Breather Selection Total assembly pressure drop flow curve µ elements Flow (US GPM) µ Δ p(bar) Δ p(psid) Flow (l/min) Ordering Information LFC62242 LFC62222 LFC LFC LFC62222 LFC LFC6224 Description Non-breathing (No element) Clamp mounting with strainer µ nom element, G2thread with strainer µ nom element, clamp mounting with strainer µ nom vented (air in) push on mounting with strainer Non-breathing (No element) 2 BSP thread with strainer µ nom element, G2 / 2 thread with strainer µ nom vented (air in) G2 thread without strainer Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. 92 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 26

11 Spin-On ir Breathers 93 Reservoir equipment

12 Spin-On ir Breathers Specification High capacity air breathers designed for the removal of airborne contamination in hydraulic systems to support environmental maintenance. Ideal for high flow systems and heavily contaminated environments. Disposable spin-on elements quickly and easily replaced. 5micron nominal quality filtration elements. 2 models available 700 l/min and 500 l/min. vailable with apressurised valve in the mounting adaptor. Standard spin-on air breather stem Ø94 Reservoir cutout Ø25 maximum Circuit symbol (standard) B Ø5 3off M6 fixing holes equispaced on 4.3 P.C.D. B Pressurised spin-on air breather stem Reservoir cutout Ø25 maximum 60 Ø97 Ø63.5 Circuit symbol (pressurised) 6 Ordering Information 3off M6 fixing holes equispaced on 50 P.C.D. Note: Spin-on air breather elements can also be mounted directly on to any suitable length of 3 / 4 BSP threaded pipe. 5µ Spin-on air breathers Supersedes ir flow Valve crack pressure mm Bmm Weight Replacement element S S S S S S *S **S *S **S l/min 500 l/min 700 l/min 700 l/min 500 l/min 500 l/min Unpressurised Unpressurised 0.35 Bar 0.70 Bar 0.35 Bar 0.70 Bar Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Note 3: Reservoir must be capable of withstanding pressurisation Kg 0.75Kg 0.69Kg 0.69Kg 0.8Kg 0.8Kg Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 27

13 High capacity air breathers and filler/breathers designed for the removal ofairborne contamination in hydraulic systems tosupport environmental maintenance. Ideal for high flow systems and heavily contaminated environments. Disposable spin-on elements quickly and easily replaced. 3micron absolute quality filtration elements. Models available 700 l/min and 3000 l/min. Ø Ø Mounting face for standard and large breather 73 PCD Ø57 hole in tank B C B D EBSPT C Ø88 boss or spot face (.6 micron surface finish) 6fitting holes Ø5.6 equispaced on 73 PCD Strainer 30mesh (600 microns) Ø48 Large breather filter Specification Maximum operating temperature: -20 C to +90 C. Construction materials: Epoxy coated steel components to resist corrosion. resistant paint finish onlarge breathers. Fluid compatibility: Suitable for use with mineral oils and water oil emulsions. Weights: Large: H Kg H Kg H Kg Each breather filler is supplied with mounting gaskets and self-tapping screws. Ordering Information Large breather dimensions Supersedes ir flow l/min H H H H Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Dimensions (mm) B C D Ports 3 / 4 / 4 95 Large breather filler dimensions Part number H H H Supersedes ir flow l/min H H H Dimensions (mm) B C Replacement element complete with bayonet H H H Supersedes H H H Reservoir equipment

14 Notes 96 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK.

15 Fluid Level Measurement Fluid Level Temperature Gauges 97 Reservoir equipment

16 Fluid Level/Temperature Gauges Specification Construction: Lens Transparent polyamide. Lens base Nylon 66. Shroud High impact polystyrene. No aluminium content. Bolts: Steel. Seals: Nitrile. Maximum working pressure: bar. Working temperature: -30 C to +90 C. Fluid compatibility: Mineral and petroleum based oils. Note: 500mm model with metal shroud finished in black available. Recommended bolt tightening torque: Nm maximum. Thermometer scale range: +30 C to +90 C. Temperature Indicator: Blue alcohol. Note:. Locate seals in mounting recess before fitting. 2. Select the size required by studying the installation details to determine apart number. Size Installation Details For through hole mounting: Thread Hole size M M2 Preferred Maximum For tapped holes: Holes tobe tapped square to mounting face. Tolerance on hole centres: For welded back nuts: The above details should be combined. Drive slot Black line Red line /F HEX Installation and pplication Information Simple to Install The universal fixing is designed for either front or rear fixing. Just two holes in the tank threaded for front fixing and the gauge is ready to install. fter positioning the gauge the bolts are simply tightened to provide asecure seal. There isno fear of leakage with the square section seals and the two-point mounting system eliminates problems with tank distortion. M and M2 bolt thread options are available. Easy to Read The high-visibility lens is one-piece for added security and moulded in shatterproof, transparent polyamide for an accurate and clear oil level and temperature indication. Further gauge protection is provided by aspecially designed shroud moulded in high-impact, black polystyrene. Size Ordering Information Standard products table Supersedes FL692 FL6923 FL69 FL693 FLT.2 FLT.23 FL. FL.3 Desciption Fluid level/temp Fluid level/temp Fluid level Fluid level Centres 76mm 76mm 76mm 76mm Thread M M2 M M2 Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Max temp 90 C 90 C 90 C 90 C Weight 0.3Kg 0.3Kg 0.3Kg 0.3Kg 98 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 28

17 Size 2Installation Details Drive slot Black line /F HEX Red line Size 2Ordering Information Standard products table Supersedes FL6922 FL69223 FL692 FL6923 FLT.22 FLT.223 FL.2 FL.23 Desciption Fluid level/temp Fluid level/temp Fluid level Fluid level Centres 27mm 27mm 27mm 27mm Thread M M2 M M2 Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Max temp 90 C 90 C 90 C 90 C Weight 0.5Kg 0.5Kg 0.5Kg 0.5Kg Size 3Installation Details Drive slot Black line /F HEX Red line 4.5 Size 3Ordering Information Standard products table Supersedes FL6932 FL69323 FL693 FL6933 FLT.32 FLT.323 FL.3 FL.33 Desciption Fluid level/temp Fluid level/temp Fluid level Fluid level Centres 254mm 254mm 254mm 254mm Thread M M2 M M2 Note :s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Max temp 90 C 90 C 90 C 90 C Weight 0.23Kg 0.23Kg 0.23Kg 0.23Kg 99 Reservoir equipment

18 Notes 200 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK.

19 Reservoir Float & Level Switches 20 Reservoir equipment

20 FL Series djustable Float Switch Features &Benefits Float Switch Features Include: Float switches can be adjusted on site Reliable design using reed switches 3 lengths available, 500mm, 00mm and 500mm The FL Series is a range of vertically mounted, single float level switches operating on the proven reed switch and magnet principle. The FL Series float switch can be tailored by the user for a particular application, by adjusting the length of the float switch tube. It is also possible for the user to select the switching configuration by inverting the float, giving either open on rise or close on rise operation. The unit is supplied part assembled, with detailed instructions for the user to complete assembly to the specifications of the application and to install the unit. The FL Series is designed to be adjusted by the user to fit their tank. The unit consists of astem with the reed switch, thermal switch (if fitted) and float already set in position. The customer can cut the stem to fit their tank, and assemble it to the header. The unit is then ready to be fitted to the tank. The unit has a factory set Open On Rise switching configuration, but this can be changed by reversing the float. The common temperature switches used are 60 C Open On Rise or 60 C Close On Rise. However, other temperature specifications may be obtained on request. standard DIN connector is supplied with the unit. Typical Specification Installation Drawing Installation Mounting: Gasket: Length: BSP threaded header 2.0mm thick sealing washer djustable up to500mm Electrical specification Supply voltage: 240 Vac maximum 300 Vdc maximum Switching current: 0.5 Thermostat ratings Normal voltage: 250V Current rating: 4 ( max) Material specification Header: Brass Stem: Brass Float: Polypropylene Gasket: Klingersil grade C4324 to BS753 grade Y Other parameters Fluid types: ny liquids compatible with brass and polypropylene HEX 36 /F Customer djustable 35 approx BSPP thread Polypropylene float Ø28.5 Ordering Information Standard products table Supersedes FL0500R FL00R FL500R FL R FL-00--0R FL R Desciption 500mm long float level switch 00mm long float level switch 500mm long float level switch Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. 202 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 29

21 CLS46 Capacitive Level Switch Features &Benefits Features Include: Rugged construction Simple to install Delay circuitry prevents false alarms Purely electronic, no moving components Integrated test feature The CLS46 Liquid Level Switch is an active device which is designed to give an alarm signal if fluid falls below a preset level. It will only give an output signal after a few seconds of low level to eliminate false alarms due to turbulence. The fact that the CLS46 Series has no moving parts and incorporates a built in delay means that it is ideal in applications where mechanically operated switches mis-trigger due to vibration and fluid turbulence. The CLS46 Capacitive Level Switch is designed to detect the loss of fluid below its position in the tank. The CLS46 Series has no moving parts and it is therefore suitable for all applications, particularly where space and access inside a vessel is at a minimum. The CLS46 Series compliments the existing range of level measurement instrumentation supplied by Parker Hannifin. Technical Specification Installation Details Dimensions: See drawing Electrical rating: Supply voltage: 7-40 Vdc Supply current: 3.0m Max. load current:.0 larm delay time:.0 seconds Connections: V+: Positive power supply GND: Negative power supply or GND Output: Transistor switched to GND on alarm Test: Ground to operate Body: Connected to ground Fluid types: Water based fluids compatible with brass, PTFE and flurosilicone across corners (HEX.2 /F) Construction: Body: Brass Probe: PTFE Terminals: SE C2 brass, tin plated Seals: Flurosilicone Connector: 30% glass filled nylon 6 Environmental ratings Max. pressure: 5.0 bar (72 PSI) Temp. ranges: Fluid: -40 C to +30 C mbient: -40 C to +0 C Storage: -50 C to +40 C Sealing: IP67 Vibration: 6g -50Hz ( rpm) Shock: 50g, 6.3mS Weight: 53g / 4 NPTF, / 2 NPTF or / 2 BSPT thread Ordering Information Standard products table Desciption CLS46 Capacitive fluid level sensor CLS46Connector Capacitive fluid level sensor connector Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. 203 Reservoir equipment

22 Fluid Power Products Hydraulic system protection from Parker is further confirmed with a quality range of fluid power products that include suction strainers, check valves pressure gauges and a pipe clamping system that will ensure secure pipe installations. For information on Parker Filtration products and technology: Tel: +44(0) Fax: +44(0) filtrationinfo@parker.com 204

23 Suction Elements 205 Reservoir equipment

24 Suction Elements Specification Installation -Suction Elements Without Bypass Construction: Stainless steel media 30% glass filled nylon head. Zintec centre tube. Epoxy adhesives. Maximum working temperature: 90ºC. Filtration media: 25 micron*. Flow range: l/min. Bypass rating: 0.7 bar. Mounting threads: G / 2 up tog3. Δ p(bar) SE.39 *Non-standard elements are available to order. Consult Parker Filtration SE.320 SE.457 SE.323 Flow (US GPM) Flow (l/min) Installation -Suction Elements with Bypass SE.324 SE.326 SE.29 SE.220 SE Δ p(psid) C/F HEX C/F HEX ØB ØB Mounting thread Mounting thread Circuit symbol Ordering Information -Without Bypass Circuit symbol Standard products table Supersedes ir flow l/min SE75 SE7522 SE75232 SE75352 SE75353 SE75364 SE75462 SE75473 SE75484 SE.39 SE.320 SE.457 SE.323 SE.324 SE.326 SE.29 SE.220 SE Ports BSP / 2 3 / 4 / 2 / / 2 3 Micron rating Dimensions (mm) B C Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability Weight kg Bypass rating Ordering Information -With Bypass Standard products table Supersedes ir flow l/min SE75 SE7522 SE75232 SE75352 SE75353 SE75364 SE75462 SE75473 SE75484 SE.50 SE.5 SE.52 SE.53 SE.54 SE.55 SE.56 SE.57 SE Ports BSP / 2 3 / 4 / 2 / / 2 3 Micron rating Dimensions (mm) B C Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability Weight kg Bypass rating 0.7 bar 0.7 bar 0.7 bar 0.7 bar 0.7 bar 0.7 bar 0.7 bar 0.7 bar 0.7 bar 206 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 30

25 Diffusers Installation Details Specification Construction: Zintec body. 30% glass-filled nylon head. Zintec end cap. Epoxy adhesives. Flow range: 50 l/min up to 454 l/min. Mounting threads: G 3 / 4 up tog2. Mounting thread ØB C/F HEX 20 plain area The effect of fitting a diffuser Note: When installing a diffuser the plain area on the outside must be facing the pump inlet. The benefits of specifying a Parker Filtration Diffuser Installing a Parker Filtration Diffuser in a hydraulic reservoir is a simple operation that can make a big difference to system efficiency. With its special concentric tubes designed with discharge holes 80 opposed fluid aeration, foaming and reservoir noise are reduced and pump life extended by reducing cavitation to the pump inlet. Ordering Information Diffusers manufactured to customer specifications and other sizes of diffusers are available. Standard products table Flow l/min Ports BSP Dimensions (mm) B C Weight kg / 2 3 / Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. 207 Reservoir equipment

26 Inline Filters Metal Inline Filter -Specification Construction: Head zinc. Bowl luminium BS470/ Element: Zintec/Stainless steel. 25 micron*. Installation Details Max. flow: 90 l/min. Max working pressure: 7bar. Thread: G. Working temperature: -30 C to +80 C. Seal: Nitrile. Bowl tightening torque: 2 Nm. Filter Selection Flow direction: From outside to inside. Weight:.5 Kg. *lternative media can be specified. G Total assembly pressure drop flow curve Oil Viscosity 30 cst Relative density Flow (US GPM) Circuit symbol Δ p(bar) Δ p(psid) 60 Minimum for bowl removal Ø off fixing holes Ø Flow (l/min) Ordering Information Standard products table.5 Flow l/min Thread BSP Micron rating Replacement element Supersedes Non-Corrodible Inline Filter -Specification IL5 90 G 25 EIL5 E.IL.5 Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Construction: Housing and bowl moulded in polyester. Element: Stainless steel mesh. 25 micron*. Max. flow: 20 l/min. Max working pressure: 7bar. Thread: G. *For alternative media consult Parker Filtration Note: When using with water, protect from freezing. Working temperature: -30 C to +80 C. (+60 C water). Seal: Nitrile. Bowl tightening torque: 2 Nm. Bowl tightening note: box or ring spanner is recommended. Flow direction: From outside to inside. Weight: 0.5 Kg. Installation Details G Ø45 63 Ø off fixing holes Ø Total assembly pressure drop flow curve Oil Viscosity 30 cst Relative density Flow (US GPM).6 2 Inlet Δ p(bar) Δ p(psid) Ø74 60 Minimum for bowl removal Ordering Information 22 /F HEX Circuit symbol Flow (l/min) Standard products table Supersedes Thread BSP ppliance Micron rating Weight Replacement element IL765 IL7625 IL.5 IL.25 Oil Water Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability R.765 R Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 30

27 Drive Couplings Technical Data Materials Coupling halves Sintered Steel Sleeve Nylon 66 Max temp sleeve 83 C To select coupling model check application to establish running load condition. Check chart for factor (F) and apply factor (F) to *Rating of coupling formulae. This answer you now apply to *Rating/0 rev/min below. It is advisable always to check shaft sizes being used on application and check with dimension H. Installation Details Factor (F) pplication Electric motor Petrol/diesel engine Uniform load Medium shock Heavy shock HP of application x0 xf *Rating of coupling= rev/min of application F G Hub withdrawal clearance Sectioned detail ØJ ØH ØC ØB E Grub screw position D Max *Rating/ H J speed 0 rev/min Weight B C D E F G max min pilot prefix rev/min kw hp mm mm mm mm mm mm mm bore bore bore DC28* DC42* DC55* min 38. max Height of keyway from base of bore Metric Imperial Standard bore BS 4500, (985) BS 96, Part, (985) Standard keyway BS 4325, Part (980) BS46, Part, (985) Ordering Examples Parker Filtration drive coupling components are ordered separately. Here are three examples of complete assemblies ordered this way.. Complete assembly DC28M4B04K Made up ofa DC28M4 DC28B04K DC28.S (Sleeve) Complete model DC28 drive coupling: One gear hub has 4mm bore with 5mm wide keyway and other hub has a / 2 bore with 0.25 wide keyway. Both hubs supplied with locating grub screw. ssembly data. Maximum angular misalignment is ±2. Maximum radial misalignment is ±0.4mm. 2. Ensure that the Parker Filtration drive coupling gear hubs are an easy fit to their respective shafts. Do not use heavy blows toforce the hubs on. 3. When in position, the hubs should have agap of 4mm as denoted by E dimension. 4. Tighten grub screws tolocate both gear hubs on to their respective shafts. 2. Complete assembly DCR42PBPB Made up of2x DCR42PB s DC42S (Sleeve) Complete model DC42 drive coupling: Both gear hubs have pilot bore of.5mm. Not supplied with grub screws. 3. Complete assembly DCR55PBB2K Made up ofa DCR55PB DC55B2K DC55S (Sleeve) Complete model DC55 drive coupling: One gear hub pilot bored 5 / 8, the other hub pilot bored / 2. Latter only supplied with grub screw. 209 Reservoir equipment

28 Drive Couplings Ordering Information Model DC.28 Supersedes Dimensions (mm) Weight ØBore Width Height DC28M6 DC28M9 DC28M20 DC28M22 DC28M24 DC28M25 DC28M28 DCR28PB DC28S DC28M DC28M DC28M4 DC28M8 DC28B03K DC28B04K DC28B05K DC28B06K DC28B07K DC28B08K DC28B09K DC.28.M6 DC.28.M9 DC.28.M20 DC.28.M22 DC.28.M24 DC.28.M25 DC.28.M28 DCR.28.PB DC.28.S DC.28.M DC.28.M DC.28.M4 DC.28.M8 DC.28.B03K DC.28.B04K DC.28.B05K DC.28.B06K DC.28.B07K DC.28.B08K DC.28.B09K 6.0mm 9.0mm 20.0mm 22.0mm 24.0mm 25.0mm 28.0mm.0mm.0mm 4.0mm 8.0mm 7 / 6 / 2 5 / 8 3 / 4 7 / 8 / 8 5.0mm 6.0mm 6.0mm 6.0mm 8.0mm 8.0mm 8.0mm 8.0mm 3.0mm 4.0mm 5.0mm 6.0mm 0.25 ins 0.25 ins 0.88 ins 0.88 ins ins ins 0.33 ins 8.4mm 2.9mm 22.9mm 24.9mm 27.5mm 28.5mm 3.5mm.5mm 2.9mm 6.4mm 20.9mm 0.50 ins 0.57 ins 0.72 ins 0.84 ins 0.99 ins.2 ins.24 ins Range from 0.259Kg to 0.4Kg Model DC.42 Supersedes Dimensions (mm) Weight ØBore Width Height DC42M25 DC42M28 DC42M30 DC42M35 DC42M38 DC42M42 DCR42PB DC42S DC42M8 DC42M9 DC42M20 DC42M22 DC42M24 DC42M32 DC42B05K DC42B06K DC42B07K DC42B08K DC42B09K DC42BK DC42BK DC42B2K DC42B3K DC.42.M25 DC.42.M28 DC.42.M30 DC.42.M35 DC.42.M38 DC.42.M42 DCR.42.PB DC.42.S DC.42.M8 DC.42.M9 DC.42.M20 DC.42.M22 DC.42.M24 DC.42.M32 DC.42.B05K DC.42.B06K DC.42.B07K DC.42.B08K DC.42.B09K DC.42.BK DC.42.BK DC.42.B2K DC.42.B3K 25.0mm 28.0mm 30.0mm 35.0mm 38.0mm 42.0mm 8.0mm 9.0mm 20.0mm 22.0mm 24.0mm 32.0mm 5 / 8 3 / 4 7 / 8 / 8 / 4 3 / 8 / 2 5 / 8 8.0mm 8.0mm 8.0mm.0mm.0mm 2.0mm 2.0mm 6.0mm 6.0mm 6.0mm 6.0mm 8.0mm.0mm 0.88 ins 0.88 ins ins ins 0.33 ins 0.33 ins ins ins ins 28.5mm 3.5mm 33.5mm 38.5mm 4.5mm 45.5mm 20.9mm 2.9mm 22.9mm 24.9mm 27.5mm 35.5mm 0.72 ins 0.84 ins 0.99 ins.2 ins.24 ins.37 ins.49 ins.6 ins.76 ins Range from 0.436Kg to 0.753Kg Model DC.55 Supersedes Dimensions (mm) Weight ØBore Width Height DCR55PB DC55S DC55M25 DC55M28 DC55M30 DC55M32 DC55M35 DC55M38 DC55M42 DC55M55 DC55B09K DC55BK DC55BK DC55B2K DC55B3K DC55B4K DC55B5K DC55B6K DC55B7K DCR.55.PB DC.55.S DC.55.M25 DC.55.M28 DC.55.M30 DC.55.M32 DC.55.M35 DC.55.M38 DC.55.M42 DC.55.M55 DC.55.B09K DC.55.BK DC.55.BK DC.55.B2K DC.55.B3K DC.55.B4K DC.55.B5K DC.55.B6K DC.55.B7K 25.0mm 28.0mm 30.0mm 32.0mm 35.0mm 38.0mm 42.0mm 55.0mm / 8 / 4 3 / 8 / 2 5 / 8 3 / 4 7 / / 8 6.0mm 8.0mm 8.0mm 8.0mm.0mm.0mm.0mm 2.0mm 6.0mm 0.33 ins 0.33 ins ins ins ins ins 0.50 ins 0.50 ins ins 28.5mm 33.5mm 33.5mm 35.5mm 38.5mm 4.5mm 45.5mm 59.5mm.24 ins.37 ins.49 ins.6 ins.76 ins.89 ins 2.0 ins 2.3 ins 2.3 ins Range from.248 Kg Kg Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. 2 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 30

29 Pipe Clamp System Multiclamp 2 Reservoir equipment

30 Pipe Clamp System Multiclamp When only the best Clamping System will do...specify Multiclamp Multiclamp is a system. system of components, each one engineered to a high standard that together build to provide effective, all-purpose pipework clamping. Multiclamp offers creative and cost-effective environmental benefits to the system designer and installer. Creating accurate runs of varying diameter tubes, pipes, hoses and cables in all industries. Secure Multiclamp installations ensure aleak free, noise free and vibration free system. The neat design of pipe line runs offers easy maintenance of machinery and plant equipment. Visual planning of line runs is straightforward with Multiclamp accurate installations can be achieved without skilled labour keeping costs down and quality up. Planning with Multiclamp These notes have been compiled to assist in planning your Multiclamp system. Multiclamp offers considerable flexibility. For example, it can fit in with a factory installation that is being built in phases. Should a last minute change in pipe diameter occur during installation, an alternative rubber bush is likely to be all that is required. Not acomplete and expensive re-think of the installation. Multiclamp metal components can be sprayed to match a vehicle livery or plant installation and, if installed properly, should require no maintenance. Installation is simple and requires no experience nyone can use Multiclamp and only the basic, everyday tools are required. From one pipe to almost any number because each Multiclamp position can be visually sighted and its position adjusted an almost guaranteed straight run can be obtained. Equally, changes of plane or direction can be achieved simply and securely. Group pipe sizes together to obtain the most economical use of three basic Multiclamp Series. Some sites will require all pipes mounted in one single plane either vertical or horizontal. When stacked modules are preferred, the only work to be done on the Multiclamp is to saw off the desired length. If alarge number of pipe lines are to be run, it is recommended that the upper clamping unit is simply cut into two lines only, and progressively assembled by securing two pipes at a time. It will be recognised that most odd lengths on site will be used, and one man can easily cope with alarge number of pipe lines by this simple progressive build up. This assembly will provide easy access for servicing and replacing pipes. This method also reduces the quantity of Stacking Nuts and Studs by 50%. If a factory installation is being built in phases, it would be wise to leave the first phase with alower clamping unit and Stacking Nuts in position ready to receive pipe runs for the next building phase. Series 6.0mm-20.0mm ( / 4-3 / 4 ) Series 6 6.0mm-28.0mm ( / 4 - ) Stacked modules or single module Series 32.0mm-50.0mm ( 3 / 8-2 ) Fixing points to suit Your maximum pipe size will determine the series to use. There is a degree of versatility provided by the rubber bushes. You choose from single or multistacked Multiclamp, whichever suits your particular installation requirements. Stacking stud and nut not required in this position 22 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 3

31 Specification Dimension details supplied in product configurator Single Clamp B C CTS ( B ) Double Clamp Ø B C C B Series PT E FREF F E D Multiclamp 2or6holes Split Bushes set of clamping units = pair es are ordered in sets only i.e. set of bushes =bushes of one size C B Thetford England Series PT Ø B Pipe size HREF G Ø D E F Material Specifications Zinc plated steel with anti-corrosive, full passivate. Multiclamp can also be multi-stacked using stacking studs and nuts. Series and 6 clamp is supplied in lengths of 603mm and Series 32 in lengths of 206mm. These can be simply cut to the required lengths for installation. Note: For stainless steel version please consult Parker. Series will accept pipe or hose diameters from 6mm up to 20mm maximum. Series 6 from 6mm up to28mm and Series 32 from mm up to 50mm. cross the 3 Series, there are 26 different high-quality split rubber bushes to select from to cope with any combination and number of different pipe and hose diameters in the same run. Stacking Nuts Stacking Studs Mounting daptors Weld Plate B Thread Thread B Ø B C D B F E Stacking nuts are ordered in sets only. i.e. set of stacking nuts = 50stacking nuts of one size. Stacking studs are ordered in sets only. i.e. set of stacking studs = 50stacking studs of one size. Mounting adaptors are not ordered in sets. i.e. off mounting adaptors = single piece. Weld plates are ordered in sets only. i.e. set of weld plates = weld plates. 23 Reservoir equipment

32 Pipe Clamp System Multiclamp Ordering Information - Series Product configurator Supersedes Description Pack Dimensions (mm) Thread quantity B C D E F G H Ø MC MC2 MC6 MCN MCS MCWP MCSB MCBMO MC.. MC..2 MC..6 MC.N. MC.S. MC.WP. MC.SB. MC.B..MO Single clamp Double clamp 6 bay clamp Stacking nut Stacking stud Weld plate Standard bolt Mounting adaptor pairs pairs pair M8 x.25 M8 x.25 M8 x.25 Pack weight 0.60 Kg.00 Kg 0.80 Kg 0.80 Kg 0.50 Kg 0.35 Kg 0.55 Kg 0.02 Kg Supersedes Description Pack Dimensions (mm) Pipe size quantity B (mm) OD MCG5 MCG6 MCG8 MCG MCG2 MCG4 MC.G..5 MC.G..6 MC.G..8 MC.G.. MC.G..2 MC.G /6 3/8 /2 5/8 3/4 /4 Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Pack weight 0.3 Kg 0.2 Kg 0.2 Kg 0. Kg 0.90 Kg 0.3 Kg Ordering Information - Product configurator Series 6 Supersedes Description Pack Dimensions (mm) Thread quantity B C D E F G H Ø MC6 MC62 MC62 MCN6 MCS MCWP MCSB MCB6MO MC.6. MC.6.2 MC.6.2 MC.N.6 MC.S. MC.WP. MC.SB. MC.B.6.MO Single clamp Double clamp 2 bay clamp Stacking nut Stacking stud Weld plate Standard bolt Mounting adaptor pairs pairs pair M8 x.25 M8 x.25 M8 x.25 Pack weight 0.80 Kg.60 Kg.00 Kg.06 Kg 0.50 Kg 0.35 Kg 0.55 Kg 0.06 Kg Supersedes Description Pack Dimensions (mm) Pipe size quantity B (mm) OD MCG65 MCG66 MCG68 MCG6 MCG62 MCG64 MCG66 MCG68 MCG64 MC.G.6.5 MC.G.6.6 MC.G.6.8 MC.G.6. MC.G.6.2 MC.G.6.4 MC.G.6.6 MC.G.6.8 MC.G /6 3/8 /2 5/8 3/4 7/8 /4 Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Pack weight 0.28 Kg 0.28 Kg 0.26 Kg 0.22 Kg 0.20 Kg 0.8 Kg 0.4 Kg 0.6 Kg 0.28 Kg 24 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 3

33 Ordering Information - Product configurator Series 32 Supersedes Description Pack Dimensions (mm) Thread quantity B C D E F G H Ø MC32 MC322 MC326 MCN32 MCS32 MCWP32 MCSB32 MCB32MO MC.32. MC.32.2 MC.32.6 MC.N.32 MC.S.32 MC.WP.32 MC.SB.32 MC.B.32.MO Single clamp Double clamp 6 bay clamp Stacking nut Stacking stud Weld plate Standard bolt Mounting adaptor pairs pairs pair M x.5 M x.5 M x.5 Pack weight 2.25 Kg 3.82 Kg 3.80 Kg.99 Kg 0.90 Kg 0.70 Kg.30 Kg 0.26 Kg Supersedes Description Pack Dimensions (mm) Pipe size quantity B (mm) OD MCG32 MCG322 MCG326 MCG328 MCG3220 MCG3224 MCG3232 MCG326 MCG328 MCG324 MCG3226 MC.G.32. MC.G.32.2 MC.G.32.6 MC.G.32.8 MC.G MC.G MC.G MC.G.32.6 MC.G.32.8 MC.G.32.4 MC.G /8 3/4 /4 /4 2 3/8 /2 7/8 Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. Pack weight. Kg. Kg.00 Kg.00 Kg 0.80 Kg 0.80 Kg 0.40 Kg.30 Kg.20 Kg.00 Kg 0.60 Kg How to build Multiclamp Reservoir equipment

34 Inline Check Valves Specification Construction: Steel UNI 55. Ball and spring: Chrome finished steel. Retainer: Nylon. Flow rates: From 20 l/min to 50 l/min. Max. working pressure: 350 bar. Valve crack pressures: 0.35 and 4.5 bar. Circuit symbol Installation Details B /F HEX Thread Technical Data Ordering Information Δ p(bar) Pressure Drop Flow Curves Flow (US GPM) Flow (l/min) Δ p(psid) Standard products table Cracking Flow pressure Thread B Weight l/min bar G mm mm Kg / 4 3 / 8 / 2 3 / 4 / 4 3 / 8 / 2 3 / Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 32

35 Single Station Gauge Isolator Valves Specification Construction: Single Station: Cast iron and steel. Knurled aluminium knob with Twist to lock or push to read type. Max. working pressure: 350 bar. Port size: Single Station: G / 4. Weight: Single Station: 0.90 Kg. Single Station Installation Details HEX nut 38.0 /F 3.0 G G / 4 TYP 3positions DR P Circuit symbol 20.0 SQ Operation Details Single Station Ordering Information Standard products table GI486 GI44 Description Single station gauge isolator twist to lock type Single station gauge isolator push to read type Weight 0.90 Kg 0.90 Kg 27 Reservoir equipment

36 63mm Dia. Pressure Gauges Specification Construction: Case: Natural finish stainless steel. Window: Non-splintering clear acrylic glass. Movement: Cu alloy. Dial: White plastic, with pointer stop pin. Pointer: Black plastic. Liquid filling: Glycerine 99.7%. Working pressure: Max 75% of the full scale value. Process temperature: + 60 C maximum. ccuracy:.6% FSD. Wetted parts connector: Copper alloy. Bourdon tube: < 60bar = Cualloy, C-type, soft soldered. > 60bar = Cualloy, helical type, soft soldered. Mounting Stem Detail Ordering Information Ø5 Ø9.5 Snubber fitted G / 4 ( / 4 BSP) 4 /F HEX Symbol Note: It is recommended that all glycerine gauges should be mounted in the vertical position with gauge case relief valve uppermost. Pressure range up to 00 bar available. Bottom Connection PGB063 PGB0636 PGB06325 PGB06340 PGB06360 PGB0630 PGB06360 PGB PGB PGB PGB06304 Supersedes PGB PGB PGB PGB PGB PGB PGB PGB PGB PGB PGB Pressure range 0- bar 0-6 bar 0-25 bar 0-40 bar 0-60 bar 0-0 bar 0-60 bar bar bar bar 0-4 bar Connector type G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom G / 4 Bottom Installation Details Bottom Connection h D G SW a b e ØD2 Panel Mounting (Lower Back) 9± 45 D G b 2 SW b e ØD2 Panel Mounting PGC063 PGC0636 PGC06325 PGC06340 PGC06360 PGC0630 PGC06360 PGC PGC PGC06304 PGC Supersedes PGC PGC PGC PGC PGC PGC PGC PGC PGC PGC PGC Pressure range 0- bar 0-6 bar 0-25 bar 0-40 bar 0-60 bar 0-0 bar 0-60 bar bar bar 0-4 bar bar Connector type G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel G / 4 Panel Dimensions (mm) Bottom Connection a b D D 2 e G h SW Weight ±0.5 ± Kg G / Dimensions (mm) Panel Mounting (Lower Back) b b2 D D 2 e G SW Weight ±0.5 ± Kg G / Note : Panel cut-out 64.5 ±0.5 Note 2: 3mm on the outside radius required to allow for fixing clamp. Panel Mounted (3-hole flange) 20 ØD2 ØD 20 ØD3 Note : Note 2: Gauge dimensions as for panel mounting option above with flange as shown below. Panel cut-out for 3-hole mounting 67±0.3. Dimensions (mm) D D2 D Panel Mounted (3-hole flange) PGF06360 PGF0630 PGF06360 PGF PGF PGF06304 PGF063 PGF0636 PGF06325 PGF06340 PGF Supersedes PGF PGF PGF PGF PGF PGF PGF PGF PGF PGF PGF Pressure range 0-60 bar 0-0 bar 0-60 bar bar bar 0-4 bar 0- bar 0-6 bar 0-25 bar 0-40 bar bar Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. *Note 3: ny subsequent changes to gauge accuracy will be notified. Connector type G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange G / 4 Panel Flange 28 Parker Hannifin Hydraulic Filter Division Europe FDHB200UK. Section 32

37 0mm Dia. Pressure Gauges Specification Construction: Case: BS 304 S5 stainless steel. Window: crylic. Movement: Brass. Dial: White aluminium. Pointer: Black aluminium. Liquid filling: Glycerine 98%. Working pressure: Full scale value. Process temperature: + 60 C maximum. ccuracy:.0% FSD. Wetted parts connector: Copper alloy. Bourdon tube: < 0 bar = Cu alloy, c-type, soft soldered. > 0 bar = stainless steel.457, helical type, brazed. Mounting Stem Detail Ø6 Ø7.5 Snubber fitted G / 2 ( / 2 BSP) 22 /F HEX Installation Details Bottom Connection h Symbol Note: It is recommended that all glycerine gauges should be mounted in the vertical position with gauge case relief valve uppermost. Dimensions (mm) Bottom Connection a b D D 2 e G h SW Weight ±0.5 ± Kg G / Dimensions (mm) Panel Mounting (Lower Back) b b2 D D 2 e G SW Weight ±0.5 ± Kg G / Note : Panel cut-out 2 ±.0 Note 2: 3mm on the outside radius required to allow for fixing clamp. Panel Mounted (3-hole flange) 20 D G SW ØD2 ØD 20 ØD3 a b e ØD2 Note : Note 2: Panel Mounting (Lower Back) 9± 45 D Gauge dimensions as for panel mounting option above with flange as shown below. Panel cut-out for 3-hole mounting 4±0.5. Dimensions (mm) G D D2 D b 2 SW b e ØD2 29 Ordering Information Bottom Connection PGB0250 PGB0400 PGB0 PGB06 PGB025 PGB040 PGB060 PGB00 PGB060 PGB0600 PGB000 Panel Mounting PGE0 PGE06 PGE025 PGE040 PGE060 PGE00 PGE060 PGE0250 PGE0400 PGE0600 PGE000 Supersedes PGB PGB PGB.0.0 PGB.0.06 PGB PGB PGB PGB.0.0 PGB.0.60 PGB PGB.0.00 Supersedes PGE.0.0 PGE.0.06 PGE PGE PGE PGE.0.0 PGE.0.60 PGE PGE PGE PGE.0.00 Pressure range bar bar 0- bar 0-6 bar 0-25 bar 0-40 bar 0-60 bar 0-0 bar 0-60 bar bar 0-00 bar Pressure range 0- bar 0-6 bar 0-25 bar 0-40 bar 0-60 bar 0-0 bar 0-60 bar bar bar bar 0-00 bar Panel Mounted (3-hole flange) PG.0250 PGF0400 PGF0 PGF06 PGF025 PGF040 PGF060 PGF00 PGF060 PGF0600 PGF000 Supersedes PGF PGF PGF.0.0 PGF.0.06 PGF PGF PGF PGF.0.0 PGF.0.60 PGF PGF.0.00 Pressure range bar bar 0- bar 0-6 bar 0-25 bar 0-40 bar 0-60 bar 0-0 bar 0-60 bar bar 0-00 bar Note : s featured with bold highlighted codes will ensure a standard product selection. Note 2: lternate displayed part number selection will require you to contact Parker Filtration for availability. *Note 3: ny subsequent changes to gauge accuracy will be notified. Connector type G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom G / 2 Bottom Connector type G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel G / 2 Panel Connector type G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange G / 2 Panel Flange Reservoir equipment