ADM SERIES GEROTOR MOTOR LOW SPEED HIGH TORQUE

Size: px

Start display at page:

Download "ADM SERIES GEROTOR MOTOR LOW SPEED HIGH TORQUE"

Gwenda Horton
5 years ago
Views:

AD SERIES EROTOR OTOR LOW SEED HIH TORQUE ALICATIONS Use the AD Series for light to medium duty applications such as grain augers and elevators, salt and sand spreaders, car wash and sweeper brushes,

The rince AD Series of high-torque, low speed motors incorporates the orbiting gerotor principle for dependable operation over a wide range of applications.

The needs of many applications requiring high starting, stall and running torque combined with slow speed are met by this motor.

1 AD SERIES EROTOR OTOR LOW SEED HIH TORQUE ALICATIONS Use the AD Series for light to medium duty applications such as grain augers and elevators, salt and sand spreaders, car wash and sweeper brushes, conveyors, winches, scissor lifts, and many other. To assure optimum motor life, run motor for approximately one hour at 30% of rated pressure before application of full load. The rince AD Series of high-torque, low speed motors incorporates the orbiting gerotor principle for dependable operation over a wide range of applications. Although dimensionally small, this motor is capable of providing considerable power over a wide speed range and is instantly reversible by simply reversing the direction of the hydraulic fluid flow. The needs of many applications requiring high starting, stall and running torque combined with slow speed are met by this motor. Ordering Code OTOR TYE: AD OTOR SIZE: OUNTIN: 2 Hole Flange 2 4 Hole Flange 4 SHAFT TYE: Standard 1* Key R 1 Splined S 1 Tapered T 1 w/cross-hole U Feature Fully reversible simply by reversing the direction of hydraulic fluid flow. Alternative port positioning for versatility of installation. (see next page). Optional shaft configurations. (see next page). odular construction for economical servicing and repair, also permits special adaptations. Filtration 10 micron or finer. (er ISO cleanliness code level 17/14. AD OTORS ONLY ORTS: 1/2 NTF (Standard) O 7/8 x 14 SAE O-Ring ort T anifold ort Face (See Next age) END LATE: (Blank for Standard) X Drain ort (if required) CROSS REFERENCE CHARLYNN H Series DANFOSS DH Series aximum Axial Thrust Load on Shaft 1000 lbs. It is not recommended to operate at a condition requiring both maximum torque and speed. Splined shafts are recommended in application operating at above 2500 in-lbs. continuous torque or under conditions of frequent reversal. AXIU AXIU AD DISLACEENT RESSURE SEED CC/REV CU.IN/REV SI Kgf/C 2 R WT.* CONT INT 0 CONT INT 0 CONT INT Intermittent operation = 10% Operation of every minute TE: NORAL OERATIN 80 0 F TO F, AX F aximum inlet pressure 2,500 psi for motors in series aximum back pressure 1,000 psi OIL: ineral based hydraulic fluid operating temperature. AD SERIES US AND OTORS CAT RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605)

2 OUNTIN DIENSIONS AD OUNTIN 1.00 DIA.X 1/4 WIDE STD. WOODRUFF KEY 1/4-20UNC.63 D. ø.9995±.0005 DIA. STRAIHT KEYED SHAFT.53 1/4-20UNC.63 D. 5/16-18UNC-.50 D. AX. THD. ENAEENT 4 OUNTIN HOLES SLINED SHAFT FULL DETH SLINE SAE 6B 1.01 RECOENDED FOR OERATIN ABOVE 2500 LB.-IN.OF TORQUE AND SUBJECT TO FREQUENT REVERSALS. * NOTE: OUNTIN DIENSIONS ARE THE SAE FOR THE AD & AE OTORS. 4 OUNTIN HOLES 3/8-16UNC-.60 D. ON A 3.25 B.C.D. 2 BOLT FLANE 4 BOLT FLANE SHAFT TYE DRAIN ORT (IF REQUIRED) DRAIN ORT #6 SAE STD. OTION "S" OTION "X" DIA DIA. HUB ø.9995±.0005 DIA SQ. BASE BLOCK ANIFOLD OUNTIN KIT KIT NO.: /2 NT ORTS ORTS KIT INCLUDES BASE BLOCK, O-RINS, AND OUNTIN BOLTS DIA HUB ORT FACE DETAIL OTORS FOR ANIFOLD ORTS OR BASE BLOCK OUNTIN OR CROSS ORT RELIEF VAVLE. OTION "T" DIA.(4) OUNTIN HOLES * NOTE: CAN ONLY BE USED ON OTORS WITH OTION "T". ORT OSITIONS US AND OTORS 2 BOLT STD. AD SERIES BOLT STD. 1/2-14NTF IE OR 7/8-14 O-RIN BOSS OR ANIFOLD OUNT L L A AD L L1 B C D 22 RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605) CAT

AE SERIES ROLLER OTOR LOW SEED HIH TORQUE The rince AE Series otors incorporate the roller principle of operation offering higher torque than the AD and extended life in heavy-duty continuous high

Although dimensionally small, this motor is capable of providing considerable power over a wide speed range and is instantly reversible by simply reversing the direction of the hydraulic fluid flow.

Ordering Code OTOR TYE: AE OTOR SIZE: 75 100 150 200 250 300 400 OUNTIN: 2 Hole Flange 2 4 Hole Flange 4 SHAFT TYE: Standard 1 Key R 1 Splined S 1 Tapered T 1 w/cross-hole U Feature Fully reversible

3 AE SERIES ROLLER OTOR LOW SEED HIH TORQUE The rince AE Series otors incorporate the roller principle of operation offering higher torque than the AD and extended life in heavy-duty continuous high torque operation along with modular, compact construction. Although dimensionally small, this motor is capable of providing considerable power over a wide speed range and is instantly reversible by simply reversing the direction of the hydraulic fluid flow. The needs of many applications requiring high starting, stall and running torque combined with slow speed are met by this motor. Ordering Code OTOR TYE: AE OTOR SIZE: OUNTIN: 2 Hole Flange 2 4 Hole Flange 4 SHAFT TYE: Standard 1 Key R 1 Splined S 1 Tapered T 1 w/cross-hole U Feature Fully reversible simply by reversing the direction of hydraulic fluid flow. Alternative port positioning for versatility of installation. (see next page). Optional shaft configurations. (specials possible). odular construction for economical servicing and repair, also permits special adaptations. Filtration 10 micron or finer. (er ISO cleanliness code level 17/14. AE OTORS ONLY ORTS: 1/2 NTF (Standard) O 7/8 x 14 SAE O-Ring ort T anifold ort Face (See Next age) END LATE: (Blank for Standard) X Drain ort (if required) CROSS REFERENCE CHARLYNN S Series WHITE ROSS-TRW DANFOSS RS Series /F Series DS Series aximum Axial Thrust Load on Shaft 1000 lbs. 0 Intermittent operation = 10% Operation of every minute It is not recommended to operate at a condition requiring both maximum torque and speed. Splined shafts are recommended in application operating at above 2500 in-lbs. continuous torque or under conditions of frequent reversal. To assure optimum motor life, run motor for approximately one hour at 30% of rated pressure before application of full load. AXIU AXIU AE DISLACEENT RESSURE SEED CC/REV CU.IN/REV SI Kgf/C 2 R WT.* CONT INT 0 CONT INT 0 CONT INT TE: NORAL OERATIN 80 0 F TO F, AX F aximum inlet pressure 2,500 psi for motors in series aximum back pressure 1,000 psi OIL: ineral based hydraulic fluid operating temperature. AE SERIES US AND OTORS CAT RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605)

4 OUNTIN DIENSIONS AE OUNTIN 3.25 SQ DRAIN ORT (IF REQUIRED) BOLT FLANE 3.25 DIA. HUB * NOTE: OUNTIN DIENSIONS ARE THE SAE FOR THE AD & AE OTORS. 4 OUNTIN HOLES 3/8-16UNC-.60 D. ON A 3.25 B.C.D. 4 BOLT FLANE 1.75 DIA HUB DRAIN ORT #6 SAE OTION "X" 1.00 DIA. X 1/4 WIDE STD. WOODRUFF KEY SHAFT TYE FULL DETH SLINE SAE 6B DIA. X 1/4 WIDE STD. WOODRUFF KEY.375 DIA THRU.625 ø.9995±.0005 DIA. ø.996±.001 DIA.9995 DIA ø.9995±.0005 DIA R- STANDARD 1" KEYED SHAFT 1/4-20 UNC.63 DEE 1/4-20UNC.63 D TAER ER FOOT S- 1" 6B SLINED T- 1" TAERED SHAFT SHAFT AE OTORS ONLY U- 1/4-20 UNC.63 DEE 1" SHAFT WITH 3/8 CROSS HOLE AE OTORS ONLY /16-18UNC-.50 D. AX. THD. ENAEENT 4 OUNTIN HOLES BASE BLOCK ANIFOLD OUNTIN KIT KIT NO.: /2 NT ORTS ORTS KIT INCLUDES BASE BLOCK, O-RINS, AND OUNTIN BOLTS ORT FACE DETAIL OTORS FOR ANIFOLD ORTS OR BASE BLOCK OUNTIN OR CROSS ORT RELIEF VAVLE..56 OTION "T".40 DIA.(4) OUNTIN HOLES * NOTE: CAN ONLY BE USED ON OTORS WITH OTION "T" FOR OTIONAL ORT OSITONS ROTATE OUNTIN FLANE US AND OTORS 2 BOLT STD. AE SERIES BOLT STD. 1/2-14NTF IE OR 7/8-14 O-RIN BOSS OR ANIFOLD OUNT L L A 4.00 B AE L L C D 24 RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605) CAT

5 erformance Data AD 50 CAT Cu. In. REV p SI AD Cu. In. REV p SI AD Cu. In. REV p SI AD Cu. In. REV p SI AD SERIES OTORS 346 Colored number on top = TORQUE (in-lbs) 280 Black number on bottom = SEED (R) AD 75 p SI is the actual pressure difference between the inlet and outlet ports. A SITUATION OF SIULTANEOUS EAK TORQUE AND AXIU R SHOULD NOT BE ALLOWED TO OCCUR. Splined shafts are recommended in applications that operate at torques higher than 2500 in-lbs. Operating motors at both low rpm (10-20 depending on disp) and low torque may result in rpm fluctuations during operation. To calculate horsepower from chart data use formula: H (out) = R x TORQUE (in-lbs) RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605) Cu. In. REV p SI AD Cu. In. REV p SI AD Cu. In. REV p SI AD 400 REATEST EFFICIENCY HIH EFFICIENCY 24.4 Cu. In. REV p SI US AND OTORS

6 US AND OTORS 26 erformance Data The performance charts reproduced on these pages indicate normal performance characteristics for the size motors indicated. Through use of the horizontal scale SI and the vertical scale the correct motor size can be determined for specific applications. Interpolation may be used for numbers not given in these charts. To assure optimum motor life, run motor for approximately one hour at 30% of rated pressure before application of full load. Be sure motor is filled with fluid prior to any load applications. These are typical motor performances and actual data may vary slightly from unit in production. AE Cu. In. REV p SI ** ** ** ** ** ** ** ** AE Cu. In. REV p SI * * * * * ** ** ** AE Cu. In. REV p SI AE SERIES OTORS LESS THAN 5 R *LESS THAN 10 R **OERATION UNDER THESE CONDITIONS NOT RECOENDED Colored number on top = TORQUE (in-lbs) Black number on bottom = SEED (R) AE 75 RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605) REATEST EFFICIENCY HIH EFFICIENCY 4.59 Cu. In. REV p SI * * ** ** ** ** ** AE Cu. In. REV p SI ** ** ** ** AE Cu. In. REV p SI ** ** AE Cu. In. REV p SI CAT

7 AD SERIES HYDRAULIC OTOR CROSS REFERENCE 4 BOLT FLANE OUNTIN 2 BOLT FLANE OUNTIN SHAFT WOODRUFF KEYED SLINED WOODRUFF KEYED SLINED ORTS 1/2 NT ANIFOLD 1/2 NT ANIFOLD 1/2 NT ANIFOLD 1/2 NT ANIFOLD DISLACEENT CU. IN./REV. OTOR BRAND RINCE AD50-4R AD75-4R AD100-4R AD150-4R AD200-4R AD250-4R AD300-4R AD400-4R CHARLYN H DANFOSS DH RINCE AD50-4RO AD75-4RO AD100-4RO AD150-4RO AD200-4RO AD250-4RO AD300-4RO AD400-4RO CHARLYN H DANFOSS DH RINCE AD50-4RT AD75-4RT AD100-4RT AD150-4RT AD200-4RT AD250-4RT AD300-4RT AD400-4RT CHARLYN H DANFOSS DH RINCE AD50-4S AD75-4S AD100-4S AD150-4S AD200-4S AD250-4S AD300-4S AD400-4S CHARLYN H DANFOSS DH RINCE AD50-4SO AD75-4SO AD100-4SO AD150-4SO AD200-4SO AD250-4SO AD300-4SO AD400-4SO CHARLYN H DANFOSS DH RINCE AD50-4ST AD75-4ST AD100-4ST AD150-4ST AD200-4ST AD250-4ST AD300-4ST AD400-4ST CHARLYN H DANFOSS DH RINCE AD50-2R AD75-2R AD100-2R AD150-4R AD200-2R AD250-2R AD300-2R AD400-2R CHARLYN H DANFOSS DH RINCE AD50-2RO AD75-2RO AD100-2RO AD150-2RO AD200-2RO AD250-2RO AD300-2RO AD400-2RO CHARLYN H DANFOSS DH RINCE AD50-2RT AD75-2RT AD100-2RT AD150-2RT AD200-2RT AD250-2RT AD300-2RT AD400-2RT CHARLYN H DANFOSS DH RINCE AD50-2S AD75-2S AD100-2S AD150-2S AD200-2S AD250-2S AD300-2S AD400-2S CHARLYN H DANFOSS DH RINCE AD50-2SO AD75-2SO AD100-2SO AD150-2SO AD200-2SO AD250-2SO AD300-2SO AD400-2SO CHARLYN H DANFOSS DH RINCE AD50-2ST AD75-2ST AD100-2ST AD150-2ST AD200-2ST AD250-2ST AD300-2ST AD400-2ST CHARLYN H DANFOSS DH NOTE: THE CROSS REFERENCE INFORATION IN THIS CHART IS TO BE USED ONLY AS A REFERENCE FOR UIDELINE UROSES ONLY. AFTER SELECTIN A ODEL FRO ABOVE, REVIEW THE OTOR SECIFICATIONS TO DETERINE COATIBILITY WITH SECIFIC ALICATION. US AND OTORS CAT RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605)

8 AE SERIES HYDRAULIC OTOR CROSS REFERENCE 4 BOLT FLANE OUNTIN 2 BOLT FLANE OUNTIN SHAFT WOODRUFF KEYED SLINED WOODRUFF KEYED SLINED ORTS 1/2 NT ANIFOLD 1/2 NT ANIFOLD 1/2 NT ANIFOLD 1/2 NT ANIFOLD DISLACEENT CU. IN./REV. OTOR BRAND RINCE AE75-4R AE100-4R AE150-4R AE200-4R AE250-4R AE300-4R AE400-4R CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-4RO AE100-4RO AE150-4RO AE200-4RO AE250-4RO AE300-4RO AE400-4RO CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-4RT AE100-4RT AE150-4RT AE200-4RT AE250-4RT AE300-4RT AE400-4RT CHARLYN S ROSS WHITE RS RS RS RS RS RS RS RINCE AE75-4S AE100-4S AE150-4S AE200-4S AE250-4S AE300-4S AE400-4S CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-4SO AE100-4SO AE150-4SO AE200-4SO AE250-4SO AE300-4SO AE400-4SO CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-4ST AE100-4ST AE150-4ST AE200-4ST AE250-4ST AE300-4ST AE400-4ST CHARLYN S ROSS WHITE RS RS RS RS RS RS RS RINCE AE75-2R AE100-2R AE150-2R AE200-2R AE250-2R AE300-2R AE400-2R CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS A RINCE AE75-2RO AE100-2RO AE150-2RO AE200-2RO AE250-2RO AE300-2RO AE400-2RO CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-2RT AE100-2RT AE150-2RT AE200-2RT AE250-2RT AE300-2RT AE400-2RT CHARLYN S ROSS WHITE RS RS RS RS RS RS RS RINCE AE75-2S AE100-2S AE150-2S AE200-2S AE250-2S AE300-2S AE400-2S CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-2SO AE100-2SO AE150-2SO AE200-2SO AE250-2SO AE300-2SO AE400-2SO CHARLYN S ROSS WHITE RS RS RS RS RS RS RS DANFOSS DS RINCE AE75-2ST AE100-2ST AE150-2ST AE200-2ST AE250-2ST AE300-2ST AE400-2ST CHARLYN S ROSS WHITE RS RS RS RS RS RS RS NOTE: THE CROSS REFERENCE INFORATION IN THIS CHART IS TO BE USED ONLY AS A REFERENCE FOR UIDELINE UROSES ONLY. AFTER SELECTIN A ODEL FRO ABOVE, REVIEW THE OTOR SECIFICATIONS TO DETERINE COATIBILITY WITH SECIFIC ALICATION. US AND OTORS 28 RINCE ANUFACTURIN CORORATION/WORLD HEADQUARTERS.O. BOX 7000 NORTH SIOUX CITY, SOUTH DAKOTA URL: E-AIL: prince@princehyd.com HONE (605) FAX (605) O.E.. CUSTOER SERVICE: (605) FAX (605) DISTRIBUTOR CUSTOER SERVICE: HONE (605) FAX (605) CAT

Spool Valve Hydraulic Motors. Spool Valve motors incorporate the proven orbit motor principle to provide high torque at low speeds.

Spool Valve Hydraulic Motors. Spool Valve motors incorporate the proven orbit motor principle to provide high torque at low speeds. Spool Valve Hydraulic Motors Spool Valve motors incorporate the proven orbit motor principle to provide high torque at low speeds. B-i Spool Valve Motors Highlights Product Description Char-Lynn spool