Electromagnetic. Brake Motors. Constant Speed Motors. Standard AC Motors A-109. Standard AC Motors Introduction. Brake Motors

Transcription

1 Standard AC Constant Speed Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Page Features and Types of A-11 General Specifi cations A-11 World K Series [6 W 9 W (1/1 HP 1/ HP)] A-116 BH Series [ W (1/ HP)] A-13 Linear Heads Pack Accessories Installation A-19

2 Standard AC Features and Types of 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) Features of Power Off Activated Type Equipped An AC power off activated type electromagnetic brake is equipped to allow the motor to stop instantaneously when the power is cut off, while still holding the load in position. Ideal for Applications Required Load Holding This configuration is ideal for vertical applications in which the load must be held. Types of Extensive Lineup The World K Series and BH Series are available. We have models with an output power range of 6 W (1/1 HP) to W (1/ HP), so that you can find one that meets your specific application. Compatible with Gearheads or Linear Heads Combination with a gearhead allows the motor to reduce to a required speed or generate higher torque. Combination with a linear head allows the motor to convert rotation to linear motion with great ease. RoHS-Compliant The World K Series and BH Series conform to the RoHS Directive that prohibits the use of six chemical substances including lead and cadmium. 9 W (1/ HP) W (1/ HP) Series World K Series Conforms to Safety Standards All World K Series models have a built-in overheat protection device and conform to major safety standards. Applicable Standards UL/CSA Standards Certified under the China Compulsory Certification System (CCC System) CE Marking (Low Voltage Directive) Motor Overheat Protection Device Thermal protector, Impedance protected Features, Lineup The Motor Bearing Life is Twice as Long as a Conventional Type A motor's life is determined by its bearing. We adopted high-performance bearing grease to lubricate this important component. As a result, the bearings of World K Series motors last twice as long as conventional bearings. Protective Earth Terminal on the Motor Global Voltage Specifications The World K Series supports the power supply voltages used in major countries. meeting the local voltage standard are readily available in major countries in Europe, Asia and North America. Lineup Frame Size Output Power Voltage Protective Earth Terminal 6 mm (.36 in.) 9 mm ( 3. in.) 6 W 9 W (1/1 HP 1/ HP) Single-Phase 11/11 VAC Single-Phase /3 VAC Three-Phase //3 VAC BH Series Smallest Frame Size among W (1/ HP) These motors achieve a high output of W (1/ HP) with a frame size of 1 mm (.9 in.). Hypoid Gear-Employed Right Angle Type is Available. Combination Type for Easy Installation With each combination type, the motor and gearhead come pre-assembled for easy installation into your equipment. Lineup Frame Size Output Power Type Voltage 1 mm (.9 in.) W (1/ HP), Hollow Shaft Type,, Solid Shaft Type, Parallel Shaft Type, Round Shaft Type Single-Phase 11/11 VAC Single-Phase /3 VAC Three-Phase //3 VAC Conforms to Safety Standards and Global Voltage Specifications A-11 ORIENTAL MOTOR GENERAL CATALOG 9/1

3 Features of Gearheads and Linear Heads Gearheads: Easy Speed Reduction and Increase Combination with a gearhead allows the motor to reduce to a required speed or generate higher torque. Gearheads come in various types including the long life, low noise gearhead and rightangle gearhead. Linear Heads: Convert Motor Rotation to Linear Motion Combination with a linear head allows the motor to convert rotation to linear motion with great ease. Linear heads are available with a square sectioned rack. RoHS-Compliant Gearheads and linear heads conform to the RoHS Directive that prohibits the use of six chemical substances including lead and cadmium. Types of Gearheads and Linear Heads Types Long Life, Low Noise GN-S Gearhead Long Life GE-S Gearhead Long Rated Life of 1 Hours The GN-S gearhead achieves a long rated life of 1 hours, twice the level of a conventional gearhead, by adopting a large, specially designed bearing and reinforced gears. Low Noise Design The GN-S gearhead generates less noise thanks to gears with a special shape and surface machining assembled with the use of advanced technology. Applicable Products 6 W (1/1 HP), 1 W (1/ HP), W (1/3 HP) or W (1/19 HP) GN pinion motor Long Rated Life of 1 Hours The GE-S gearhead achieves a long rated life of 1 hours, twice the level of a conventional gearhead, by adopting a large, specially designed bearing and reinforced gears. The GE-S gearhead comes with a tapped hole at the tip of the shaft. Motor Gearhead Pinion Shaft Motor Linear Head Combine gearheads and linear heads with a pinion shaft type motor. Gearheads and linear heads are sold separately. BH Series comes with the gearhead pre-assembled. Features Sound Pressure Level [db(a)] : Long Life, Low Noise GN-S Gearhead IKGN-AWJ/GN1S : GN-K Gearhead (Conventional ) IKGN-A/GN1K [Measurement conditions] Load: 1. N m Direction: Clockwise Measurement distance: 1 m (Measured in A-weighted sound pressure level) K 1.6K.K K 6.3K 1K 16K K K 3.1K K K 1.K K Frequency [Hz] Applicable Products 6 W (1/1 HP) or 9 W (1/ HP) GE pinion motor Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearhead Page A-39 Rack-and-Pinion Mechanism LS Linear Heads Page A-9 Ideal Space-Saving Solution The gear shaft is positioned at right angles with the motor shaft, enabling space-saving. Applicable Products W (1/3 HP), W (1/19 HP), 6 W (1/1 HP) or 9 W (1/ HP) pinion motor Easy to Achieve Linear Motion A rack-and-pinion mechanism is combined with a reduction mechanism, which allows the motor to convert rotation to linear motion with great ease. Hollow Shaft and Solid Shaft Types are Available Select an appropriate type that suits your specific application. Solid shaft type of GE pinion gearhead comes with a tapped hole at the tip of the shaft. Gearheads Linear Heads Pack Accessories Installation A-111

4 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) Product Line of Series World K Series BH Series Voltage (VAC) 6 mm (.36 in.) 6 W (1/1 HP) 7 mm (.76 in.) 1 W (1/ HP) Motor Frame Size, Output Power mm ( 3.1 in.) W (1/3 HP) W (1/19 HP) 9 mm ( 3. in.) 6 W (1/1 HP) 9 W (1/ HP) Single-Phase 11/11 Single-Phase /3 Three-Phase //3 Single-Phase 11/11 Single-Phase /3 Three-Phase //3 Product Line of Gearheads and Linear Heads Gearheads 1 mm (.9 in.) W (1/ HP) Gearhead Applicable Motor Rated Life Type of Gearhead Type of Pinion Series Output Power Type of Pinion (hours) Low Noise W (1/19 HP) Long Life, Low Noise GN-S Gearhead GN Type Pinion Shaft World K Series 6 W W (1/1 HP 1/19 HP) GN Type Pinion Shaft 1 6 W (1/1 HP) Parallel Shaft GN-K Gearhead GN Type Pinion Shaft World K Series 6 W W (1/1 HP 1/19 HP) GN Type Pinion Shaft 9 W (1/ HP) W (1/ HP) Shaft Long Life GE-S Gearhead Hollow Shaft Gearhead Solid Shaft Gearhead GE Type Pinion Shaft GN Type Pinion Shaft GE Type Pinion Shaft GN Type Pinion Shaft GE Type Pinion Shaft World K Series World K Series World K Series World K Series World K Series 6 W, 9 W (1/1 HP, 1/ HP) W, W (1/3 HP, 1/19 HP) 6 W, 9 W (1/1 HP, 1/ HP) W, W (1/3 HP, 1/19 HP) 6 W, 9 W (1/1 HP, 1/ HP) GE Type Pinion Shaft GN Type Pinion Shaft GE Type Pinion Shaft GN Type Pinion Shaft GE Type Pinion Shaft 1 Linear Heads Type of Linear Head Square Sectioned Rack LS Linear Head World K Series Applicable Motor Series Output Power Type of Pinion 6 W, W (1/1 HP, 1/3 HP) GN Type Pinion Shaft A-11 ORIENTAL MOTOR GENERAL CATALOG 9/1

5 System Configuration Gearheads and Linear Heads (Sold separately) Parallel Shaft Gearheads ( Page A-111) Gearheads ( Page A-39) Linear Heads ( Page A-9) Hollow Shaft Type Solid Shaft Type Standard AC Introduction Motor (Pinion Shaft) Capacitor Cap (Included) AC Power Supply (Main power supply) Peripheral Equipment (Sold separately) 1 Pack SBW ( Page A-77) Induction Reversible V Series Capacitor (Included) Clutch & Accessories (Sold separately) Synchronous Low-Speed Synchronous Mounting Brackets ( Page A-) 3Flexible Couplings ( Page A-9) CR Circuit for Surge Suppression ( Page A-3) No. Product Name Overview Page 1 3 Pack Mounting Brackets Flexible Couplings Use this brake pack to stop the motor instantaneously, perform bi-directional operation, and more. Dedicated mounting bracket for the motor and gearhead. Clamp type coupling that connects the motor or gearhead shaft to the driven shaft. A-77 A- A-9 CR Circuit for Surge Suppression Used to protect relay and switch contacts (EPCR11-). A-3 Watertight, Dust-Resistant Gearheads Example of System Configuration (Sold separately) (Sold separately) Motor Long Life, (Pinion shaft) Low Noise Gearhead Mounting Bracket Flexible Coupling RKGN-AWMU GNSA SOLU1 MCL3F6F6 Both of gearheads and linear heads cannot be combined with round shaft type motors. The system configuration shown above is an example. Other combinations are available. Linear Heads Pack Accessories Installation A-113

6 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) Product Number Code World K Series R K GN - AW M U Motor Frame Size : 6 mm (.36 in.) 3: 7 mm (.76 in.) : mm (3.1 in.) : 9 mm (3. in.) Motor Type I: Induction Motor R: Reversible Motor 3 Series K: K Series Output Power (W) (Example) : W (1/19 HP) Motor Shaft Type, Type of Pinion A: Round Shaft GN: GN Type Pinion Shaft GE: GE Type Pinion Shaft 6 Power Supply Voltage AW: Single-Phase 11/11 VAC : Single-Phase /3 VAC SW: Three-Phase //3 VAC 7 : RoHS-Compliant M: Power Off Activated Type 9 Included Capacitor U: For Single-Phase 11/11 VAC E: For Single-Phase /3 VAC Blank: Three-Phase Type The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 (Example) : RKGN-AWMU Motor nameplate and product approved under various safety standards: RKGN-AWM W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Gearhead GN SA Gearhead Frame Size : 6 mm (.36 in.) 3: 7 mm (.76 in.) : mm (3.1 in.) : 9 mm (3. in.) Type of Pinion GN: GN Type Pinion GE: GE Type Pinion 3 Gear Ratio (Example) : Gear Ratio of :1 1X denotes the decimal gearhead of gear ratio 1:1 GN Type Pinion SA: Long Life, Low Noise GN-S Gearhead, RoHS-Compliant KA: GN-K Gearhead, RoHS-Compliant RH:, Hollow Shaft Gearhead, RoHS-Compliant RAA:, Solid Shaft Gearhead, RoHS-Compliant GE Type Pinion SA: Long Life GE-S Gearhead, RoHS-Compliant RH:, Hollow Shaft Gearhead, RoHS-Compliant RAA:, Solid Shaft Gearhead, RoHS-Compliant BH Series BH I 6 F M T - 1 RH Series BH: BH Series Motor Type I: Induction Motor 3 Motor Frame Size 6: 1 mm (.9 in.) Output Power (W) (Example) : W (1/ HP) Power Supply Voltage F: Single-Phase 11/11 VAC E: Single-Phase /3 VAC S: Three-Phase //3 VAC 6 M: Power Off Activated Type 7 T: Terminal Box Type Gear Ratio, Motor Shaft Type A: Round Shaft Type Number: Gear Ratio of Combination Type 9 Type of Gearhead RH:, Hollow Shaft Type RA:, Solid Shaft Type Blank: Parallel Shaft Type (Combination type only) A-11 ORIENTAL MOTOR GENERAL CATALOG 9/1

7 General Specifications World K Series Item Specifications Insulation Resistance 1 MΩ or more when VDC megger is applied between the windings and the case after rated motor operation under normal ambient temperature and humidity. Dielectric Strength Sufficient to withstand 1. kvac at Hz or 6 Hz applied between the windings and the case for 1 minute after rated motor operation under normal ambient temperature and humidity. Temperature Rise Temperature rise of windings are C (1 F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate. [Three-phase type: 7 C (16 F) or less] Insulation Class Class B [13 C (66 F)] Overheat Protection 6 W (1/1 HP) type has impedance protection. All others have built-in thermal protector (automatic return type) Open: 13± C (66±9 F), Close: ±1 C (179.6±7 F) Ambient Temperature Single-phase 11/11 VAC, Single-phase /3 VAC, Three-phase /3 VAC: 1 + C (+1 +1 F) (non-freezing) Three-phase VAC: 1 + C (+1 +1 F) (non-freezing) Ambient Humidity % or less (non-condensing) Degree of Protection 6 W (1/1 HP), 1 W (1/ HP), W (1/3 HP), W (1/19 HP) Type: IP 6 W (1/1 HP), 9 W (1/ HP) Type: IP Heat radiation plate (Material: Aluminum) Motor Type Size: mm (in.) Thickness: mm (in.) 6 W (1/1 HP) Type (.3.3) 1 W (1/ HP) Type 1 1 (.9.9) W (1/3 HP) Type (.31.31) (.) W (1/19 HP) Type (6. 6.) 6 W (1/1 HP), 9 W (1/ HP) Type ( ) Standard AC Introduction Induction Reversible BH Series Item Insulation Resistance Dielectric Strength Temperature Rise Insulation Class Overheat Protection Ambient Temperature Ambient Humidity Degree of Protection Specifications 1 MΩ or more when VDC megger is applied between the windings and the case after rated operation under normal ambient temperature and humidity. Sufficient to withstand 1. kvac at Hz or 6 Hz applied between the windings and the case for 1 minute after rated operation under normal ambient temperature and humidity. Temperature rise of windings are 7 C (16 F) or less measured by the resistance change method after rated operation under normal ambient temperature and humidity with connecting a gearhead or equivalent heat radiation plate. Class B [13 C (66 F)] Built-in thermal protector (automatic return type) Open: 1± C (3±9 F), Close: 96±1 C (.±7 F) Single-phase 11/11 VAC, Single-phase /3 VAC, Three-phase /3 VAC: 1 + C (+1 +1 F) (non-freezing) Three-phase VAC: 1 + C (+1 +1 F) (non-freezing) % or less (non-condensing) IP (excluding the installation surface of the round shaft type) Heat radiation plate: 3 3 mm ( in.), Thickness: mm (. in.) (Material: Aluminum) V Series Clutch & Synchronous Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Pack Accessories Installation A-11

8 Standard AC Power Off Activated Type 6 W (1/1 HP) Frame Size: 6 mm (.36 in.) (Gearhead sold separately) 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Specifications Motor This type of motor does not contain a built-in friction brake mechanism. Pinion Shaft Type RK6GN-AWMU RK6GN-ME Round Shaft Type RK6A-AWMU RK6A-ME Rating 3 minutes 3 minutes IK6GN-SWM IK6A-SWM Continuous Output Power Voltage Frequency Current W HP VAC Hz A 6 1/1 6 1/1 6 1/1 Starting mn m oz-in Single-Phase Single-Phase Single-Phase Single-Phase 3 Three-Phase Three-Phase Three-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 Details of safety standards Page G- Details of RoHS Directive Page G-3 : Impedance protected Rated Rated Speed Capacitor mn m oz-in r/min μf (Power Off Activated Type) Motor RK6GN-AWMU RK6A-AWMU RK6GN-ME RK6A-ME IK6GN-SWM IK6A-SWM Voltage Frequency Current Input Holding VAC Hz A W Single-Phase 11 Single-Phase Single-Phase 6 Single-Phase Single-Phase 6 Single-Phase Single-Phase mn m oz-in Product Line Motor Pinion Shaft Type Round Shaft Type RK6GN-AWMU RK6A-AWMU RK6GN-ME RK6A-ME IK6GN-SWM IK6A-SWM The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual Only for single-phase motors A-116 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-116

9 Parallel Shaft Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Gearmotor Table Gearheads and decimal gearheads are sold separately. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is % less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is 3 N m (6 lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RK6GN-ME IK6GN-SWM GN SA Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RK6GN-AWMU RK6GN-ME IK6GN-SWM GN SA Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) Page A-16 Gearhead Page A Permissible Load Inertia J of Gearhead Page A-17 Long Life, Low Noise GN-S Gearhead The following items are included in each product. Gearhead, Mounting Screws, Operating Manual 3, 3.6,, 6, 7., 9, 1., GN SA 1, 1,, 3, 36,, 6, 7, 9, 1, 1, 1, 1 GN1XS (Decimal Gearhead) Following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental Motor sales office. Gearhead Type Gearhead Gear Ratio Parallel GN KA 3 1 Shaft GN-K Gearhead GN1XK (Decimal Gearhead) Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-116 / Characteristics A-11 / Dimensions A-11 / Connection Diagrams A-119 A-117

10 Standard AC Starting and Braking Characteristics (Reference Values) Single-Phase Motor Three-Phase Motor Single-Phase Hz Three-Phase Hz Single-Phase 6 Hz Three-Phase 6 Hz 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) Overrun [Rotations] 3 1 Time [ms] 1 Braking Time 1 Starting Time Overrun [ 1 kg m ] Load Inertia J [oz-in ] Overrun [Rotations] 3 1 Time [ms] 1 Braking Time 1 Starting Time Overrun [ 1 kg m ] Load Inertia J [oz-in ] 9 W (1/ HP) W (1/ HP) Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page A-31 Motor/Gearhead Mass: Motor.9 kg (1.9 lb.) Gearhead. kg (. lb.) ϕ6 (ϕ.36) 11 (.3) 7 (.) L 3 (1.6) 1.7 (.) (.) 7.37 (.93) ϕ ϕ.31.6 (/16") 1 (.39) ϕ (ϕ.9) 6 (.36) ϕ. (ϕ.) Thru 3 Motor Leads 3 mm (1 in.) Length UL Style 371, AWG Break Leads 3 mm (1 in.) Length UL Style 366, AWG 6 (.36) Motor Gearhead Gear Ratio L DXF RK6GN-AWMU RK6GN-ME IK6GN-SWM GN SA. 7±. (.76±.) Protective Earth Terminal M (.) max. 1. (.) Protective Earth Terminal M 1. (.61) 3 (1.1) (1.7) Detail Drawing of Protective Earth Terminal A6AU A6BU Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass:.9 kg (1.9 lb.) A63 (.9) (.) ϕ6.1 ( ϕ.36. ) ϕ.3 ( ϕ.16.1 ) 6 (.36) ϕ. (ϕ.) Thru. 7±. (.76±.) Protective Earth Terminal M (.) max. Decimal Gearhead Can be connected to GN pinion shaft type. GN1XS Mass:. kg (. lb.) A3 3. (1.1) 6 1. (1.) (.9) (.) ϕ.3 (ϕ.16.1) 6 (.36) ϕ. (ϕ.) Thru 7±. (.76±.) A-11 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-116

11 Capacitor (Included with single-phase motors) A ϕ.3 (ϕ.169) AMP#17 (.79) B. (.1) (.16) 1 C (.39) B+1 (.39) 6 (.) Capacitor Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type Capacitor RK6GN-AWMU RK6A-AWMU CH3FAUL RK6GN-ME RK6A-ME CHBFAUL A B C 31 (1.) 31 (1.) 17 (.67) 17 (.67) 7 (1.6) 7 (1.6) Mass g (oz.) (.7) 3 (.1) Capacitor Cap Included Standard AC Introduction Induction Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. represents the clockwise direction, while C represents the counterclockwise direction. Connection diagrams are also valid for the equivalent round shaft type. Single-Phase Motor Three-Phase Motor RK6GN-AWMU RK6GN-ME IK6GN-SWM L N L1(R) L(S) L3(T) R SW R R C C C ON ON C R R R C C C White Red Black C Motor Orange Orange Capacitor Red White Black Motor Orange Orange PE PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To rotate the motor in a clockwise () direction, turn SW to. To rotate the motor in a counterclockwise (C) direction, turn SW to C. Switch No. PE: Protective Earth R and C indicate CR circuit for surge suppression. [R = Ω, C =.1. μf, WV ( WV)] EPCR11- (CR circuit) is available as an accessory. Page A-3 How to connect a capacitor Page A-313 Linear Head, Accessories and Peripheral Equipment Linear Motion Linear Heads Page A-9 Instantaneous Stop Pack Page A-77 Accessories Page A-7 SW Specifications Single-Phase Single-Phase 11/11 VAC Input /3 VAC Input 1 VAC 3 A minimum VAC 1. A minimum (Inductive Load) (Inductive Load) Note Switched Simultaneously operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To change the rotation direction, change any two connections between L1(R), L(S) and L3(T). Switch No. Specifications VAC 1. A minimum (Inductive Load) Note Switched Simultaneously Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-116 / Characteristics A-11 / Dimensions A-11 / Connection Diagrams A-119 A-119

12 Standard AC Power Off Activated Type 1 W (1/ HP) Frame Size: 7 mm (.76 in.) (Gearhead sold separately) 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Specifications Motor This type of motor does not contain a built-in friction brake mechanism. Pinion Shaft Type 3RK1GN-AWMU 3RK1GN-ME Round Shaft Type 3RK1A-AWMU 3RK1A-ME Rating 3 minutes 3 minutes Output Power Voltage Frequency Current W HP VAC Hz A 1 1/ 1 1/ Starting mn m oz-in Single-Phase Single-Phase Single-Phase Single-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 Details of safety standards Page G- Details of RoHS Directive Page G-3 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. (The power supply to the electromagnetic brake is kept and the brake is released.) When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. (Power Off Activated Type) Voltage Frequency Current Input Holding Motor mn m VAC Hz A W oz-in 3RK1GN-AWMU Single-Phase RK1A-AWMU Single-Phase Single-Phase 3RK1GN-ME RK1A-ME 11.3 Single-Phase Rated Rated Speed Capacitor mn m oz-in r/min μf Product Line Motor Pinion Shaft Type Round Shaft Type 3RK1GN-AWMU 3RK1A-AWMU 3RK1GN-ME 3RK1A-ME The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual Parallel Shaft Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Long Life, Low Noise GN-S Gearhead The following items are included in each product. Gearhead, Mounting Screws, Operating Manual 3, 3.6,, 6, 7., 9, 1., 3GN SA 1, 1,, 3, 36,, 6, 7, 9, 1, 1, 1, 1 3GN1XS (Decimal Gearhead) Following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental Motor sales office. Gearhead Type Gearhead Gear Ratio Parallel 3GN KA 3 1 Shaft GN-K Gearhead 3GN1XK (Decimal Gearhead) A-1 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

13 Gearmotor Table Gearheads and decimal gearheads are sold separately. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is % less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead 3RK1GN-ME 3GN SA Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead 3RK1GN-AWMU 3RK1GN-ME 3GN SA Standard AC Introduction Induction Reversible V Series Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) Page A-16 Gearhead Page A-16 Permissible Load Inertia J of Gearhead Page A-17 Starting and Braking Characteristics (Reference values) Clutch & Synchronous Low-Speed Synchronous Single-Phase Hz Single-Phase 6 Hz Watertight, Dust-Resistant Overrun [Rotations] 3 Time [ms] 1 1 Braking Time Gearheads 1 Starting Time Overrun [ 1 kg m ] Load Inertia J [oz-in ] Linear Heads Pack Accessories Installation Product Line A-1 / Characteristics A-11 / Dimensions A-1 / Connection Diagrams A-13 A-11

14 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page A-31 Motor/Gearhead Mass: Motor 1.3 kg (.9 lb.) Gearhead. kg (1.1 lb.) ϕ7 (ϕ.76) 1 (.7) 7 (.) L (.) 3 (1.6) 1.7 (.). (.37) ϕ9..1 ϕ.37.6 (3/") 1 (.9) 3 Motor Leads 3 mm (1 in.) Length UL Style 371, AWG Break Leads 3 mm (1 in.) Length UL Style 366, AWG ϕ3 (ϕ1.1) 7 (.76) ϕ. (ϕ.17) Thru Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass: 1.3 kg (.9 lb.) A6 (.) 3 (1.6) ϕ6.1 (ϕ.36.) ϕ6.3 (ϕ.197.1) 7 (.76) ϕ. (ϕ.17) Thru ±. (3.3±.) Protective Earth Terminal M (.) max. 7 (.76). Motor Gearhead Gear Ratio L DXF 3RK1GN-AWMU 3RK1GN-ME ±. (3.3±.) Protective Earth Terminal M (.) max. 3GN SA 1. (.) Protective Earth Terminal M Decimal Gearhead Can be connected to GN pinion shaft type. 3GN1XS Mass:.3 kg (.66 lb.) A9 3 (1.69) 3 13 (1.1) (.1) (.) ϕ6.3 (ϕ.197.1) 7 (.76) ϕ. (ϕ.17) Thru 3 (1.6) (1.6) 16. (.6) Detail Drawing of Protective Earth Terminal ±. (3.3±.) A6AU A6BU. Capacitor (Included) A ϕ.3 (ϕ.169) AMP#17 (.79) B. (.1) (.16) 1 C (.39) B+1 (.39) 6 (.) Capacitor Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type Capacitor 3RK1GN-AWMU 3RK1A-AWMU CH6CFAUL 3RK1GN-ME 3RK1A-ME CH1BFAUL A B C 3 (1.) 3 (1.) 1 (.3) 1 (.3) 31 (1.) 31 (1.) Mass g (oz.) 3 (1.) 37 (1.31) Capacitor Cap Included A-1 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

15 Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. represents the clockwise direction, while C represents the counterclockwise direction. Connection diagrams are also valid for the equivalent round shaft type. 3RK1GN-AWMU 3RK1GN-ME L N R SW R R C C C ON ON C White Red Black C Motor Orange Orange Capacitor operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To rotate the motor in a clockwise () direction, turn SW to. To rotate the motor in a counterclockwise (C) direction, turn SW to C. Switch No. SW PE: Protective Earth R and C indicate CR circuit for surge suppression. [R = Ω, C =.1. μf, WV ( WV)] EPCR11- (CR circuit) is available as an accessory. Page A-3 How to connect a capacitor Page A-313 PE Specifications Single-Phase Single-Phase 11/11 VAC Input /3 VAC Input 1 VAC 3 A minimum VAC 1. A minimum (Inductive Load) (Inductive Load) Note Switched Simultaneously Standard AC Introduction Induction Reversible V Series Accessories and Peripheral Equipment Instantaneous Stop Pack Page A-77 Accessories Page A-7 Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-1 / Characteristics A-11 / Dimensions A-1 / Connection Diagrams A-13 A-13

16 Standard AC Power Off Activated Type W (1/3 HP) Frame Size: mm ( 3.1 in.) (Gearhead sold separately) 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Specifications Motor This type of motor does not contain a built-in friction brake mechanism. Pinion Shaft Type RKGN-AWMU RKGN-ME Round Shaft Type RKA-AWMU RKA-ME Rating 3 minutes 3 minutes IKGN-SWM IKA-SWM Continuous Output Power Voltage Frequency Current W HP VAC Hz A 1/3 1/3 1/3 Single-Phase 11 Single-Phase Single-Phase 6. Single-Phase 3 Three-Phase Starting mn m oz-in Three-Phase Three-Phase 3.1 The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 Details of safety standards Page G- Details of RoHS Directive Page G-3 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. (The power supply to the electromagnetic brake is kept and the brake is released.) When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. Rated Rated Speed Capacitor mn m oz-in r/min μf (Power Off Activated Type) Voltage Frequency Current Input Holding Motor mn m VAC Hz A W oz-in RKGN-AWMU Single-Phase RKA-AWMU Single-Phase Single-Phase 6 RKGN-ME 1. 7 RKA-ME Single-Phase Single-Phase IKGN-SWM IKA-SWM Single-Phase 1. 6 Single-Phase 3 Product Line Motor Pinion Shaft Type Round Shaft Type RKGN-AWMU RKA-AWMU RKGN-ME RKA-ME IKGN-SWM IKA-SWM The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual Only for single-phase motors A-1 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

17 Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Gearmotor Table Gearheads and decimal gearheads are sold separately. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is % less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is N m (7 lb-in). When a gearhead of :1 36:1 is connected, the value for permissible torque is 6 N m (3 lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RKGN-ME IKGN-SWM GN SA GN SA Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RKGN-AWMU RKGN-ME IKGN-SWM ( VAC) IKGN-SWM (/3 VAC) Long Life, Low Noise GN-S Gearhead Hollow Shaft Solid Shaft Long Life, Low Noise GN-S Gearhead GN SA GN SA GN SA GN SA 3, 3.6,, 6, 7., 9, 1., 1, 1,, 3, 36,, 6, 7, 9, GN RH 1, 1, 1, 1 GN RAA GN1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Gasket, Operating Manual Following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental Motor sales office. Gearhead Type Gearhead Gear Ratio Parallel GN KA 3 1 Shaft GN-K Gearhead GN1XK (Decimal Gearhead) Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Gearmotor Table When Gearhead is Attached Page A- Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) Page A-16 Gearhead Page A-16 Permissible Load Inertia J of Gearhead Page A-17 Linear Heads Pack Accessories Installation Product Line A-1 / Characteristics A-16 / Dimensions A-16 / Connection Diagrams A-17 A-1

18 Standard AC Starting and Braking Characteristics (Reference values) Single-Phase Motor Single-Phase Hz Single-Phase 6 Hz Three-Phase Motor Three-Phase Hz Three-Phase 6 Hz 6 W (1/1 HP) 1 W (1/ HP) Overrun [Rotations] 3 Time [ms] 1 1 Braking Time Starting Time Overrun [Rotations] 3 Time [ms] 1 1 Braking Time Starting Time W (1/3 HP) 1 Overrun 1 Overrun W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) [ 1 kg m ] Load Inertia J [oz-in ] Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page A-31 Motor/Gearhead Mass: Motor. kg (. lb.) Gearhead.6 kg (1.3 lb.) ϕ79 (ϕ3.11) 13 (.1) 7 (.) L 6 (.) 3 (1.6) 1.7 (.). (.37) ϕ9..1 ϕ.37.6 (3/") 1 (.9) ϕ3 (ϕ1.3) (3.1) ϕ. (ϕ.17) Thru 3 Motor Leads 3 mm (1 in.) Length UL Style 371, AWG Leads 3 mm (1 in.) Length UL Style 366, AWG (3.1) [ 1 kg m ] Load Inertia J [oz-in ] Motor Gearhead Gear Ratio L DXF RKGN-AWMU RKGN-ME IKGN-SWM 9±. (3.7±.) Protective Earth Terminal M (.) max. GN SA 1. (.) Protective Earth Terminal M 3 (1.6). (1.67) 16. (.6) Detail Drawing of Protective Earth Terminal A66AU A66BU Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass:. kg (. lb.) A67 3 (1.6) (.) (.9) 7 (.) ϕ.1 ( ϕ.31.6 ) ϕ73.3 ( ϕ.7.1 ) ( 3.1) ϕ. (ϕ.17) Thru. 9±. (3.7±.) Protective Earth Terminal M (.) max. Decimal Gearhead Can be connected to GN pinion shaft type. GN1XS Mass:. kg (. lb.) A13. (1.79) (1.6) (.3) (.) ϕ73.3 (ϕ.7.1) ( 3.1) ϕ. (ϕ.17) Thru 9±. (3.7±.) A-16 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

19 Capacitor (Included with single-phase motors) A ϕ.3 (ϕ.169) AMP#17 (.79) B. (.1) (.16) 1 C (.39) B+1 (.39) 6 (.) Capacitor Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type RKGN-AWMU RKA-AWMU Capacitor CHCFAUL RKGN-ME RKA-ME CHBFAUL A B C (1.9) (1.9) 1 (.3) 19 (.7) 31 (1.) 9 (1.1) Mass g (oz.) 1 (1.) 36 (1.7) Capacitor Cap Included Standard AC Introduction Induction Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. represents the clockwise direction, while C represents the counterclockwise direction. Connection diagrams are also valid for the equivalent round shaft type. Single-Phase Motor Three-Phase Motor RKGN-AWMU RKGN-ME IKGN-SWM L N L1(R) L(S) L3(T) R SW R R C C C ON ON C R R R C C C White Red Black C Motor Orange Orange Capacitor Red White Black Motor Orange Orange PE PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To rotate the motor in a clockwise () direction, turn SW to. To rotate the motor in a counterclockwise (C) direction, turn SW to C. Switch No. SW Specifications Single-Phase Single-Phase 11/11 VAC Input /3 VAC Input 1 VAC 3 A minimum VAC 1. A minimum (Inductive Load) (Inductive Load) Note Switched Simultaneously operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To change the rotation direction, change any two connections between L1(R), L(S) and L3(T). Switch No. PE: Protective Earth R and C indicate CR circuit for surge suppression. [R = Ω, C =.1. μf, WV ( WV)] EPCR11- (CR circuit) is available as an accessory. Page A-3 How to connect a capacitor Page A-313 Gearhead, Linear Head, Accessories and Peripheral Equipment Space-Saving Linear Motion Instantaneous Stop Accessories Gearheads Linear Heads Pack Page A-39 Page A-9 Page A-77 Page A-7 Specifications VAC 1. A minimum (Inductive Load) Note Switched Simultaneously Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-1 / Characteristics A-16 / Dimensions A-16 / Connection Diagrams A-17 A-17

20 Standard AC Power Off Activated Type W (1/19 HP) Frame Size: 9 mm ( 3. in.) (Gearhead sold separately) 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Specifications Motor This type of motor does not contain a built-in friction brake mechanism. Pinion Shaft Type RKGN-AWMU RKGN-ME Round Shaft Type RKA-AWMU RKA-ME Rating 3 minutes 3 minutes IKGN-SWM IKA-SWM Continuous Output Power Voltage Frequency Current W HP VAC Hz A 1/19 1/19 1/19 Single-Phase 11 Single-Phase Single-Phase 6.3 Single-Phase 3 Three-Phase Starting mn m oz-in Three-Phase Three-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 Details of safety standards Page G- Details of RoHS Directive Page G-3 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. (The power supply to the electromagnetic brake is kept and the brake is released.) When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. Rated Rated Speed Capacitor mn m oz-in r/min μf (Power Off Activated Type) Voltage Frequency Current Input Holding Motor mn m VAC Hz A W oz-in RKGN-AWMU Single-Phase RKA-AWMU Single-Phase 11 Single-Phase 6 RKGN-ME. 7 RKA-ME Single-Phase 3 6 Single-Phase IKGN-SWM 6. 7 IKA-SWM Single-Phase 6 Single-Phase 3 A-1 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

21 Product Line Motor Pinion Shaft Type Round Shaft Type RKGN-AWMU RKA-AWMU RKGN-ME RKA-ME IKGN-SWM IKA-SWM The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual Only for single-phase motors Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life, Low Noise GN-S Gearhead Hollow Shaft Solid Shaft Long Life, Low Noise GN-S Gearhead GN SA 3, 3.6,, 6, 7., 9, 1., 1, 1,, 3, 36,, 6, 7, 9, GN RH 1, 1, 1, 1 GN RAA GN1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Gasket, Operating Manual Standard AC Introduction Induction Reversible Gearmotor Table Gearheads and decimal gearheads are sold separately. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is % less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is 1 N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RKGN-ME IKGN-SWM GN SA GN SA Following gearheads are also available. For details, please refer to website ( or contact the nearest Oriental Motor sales office. Gearhead Type Gearhead Gear Ratio Parallel GN KA 3 1 Shaft GN-K Gearhead GN1XK (Decimal Gearhead) V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant 6 Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RKGN-AWMU RKGN-ME IKGN-SWM GN SA GN SA Gearheads Linear Heads Pack Accessories Installation Product Line A-19 / Characteristics A-13 / Dimensions A-13 / Connection Diagrams A-13 A-19

22 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) Gearmotor Table When Gearhead is Attached Page A- Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) Page A-16 Gearhead Page A-16 Permissible Load Inertia J of Gearhead Page A-17 Starting and Braking Characteristics (Reference values) Single-Phase Motor Overrun [Rotations] 3 Time [ms] 1 1 Single-Phase Hz Single-Phase 6 Hz Overrun Braking Time Starting Time Three-Phase Motor Overrun [Rotations] 3 Time [ms] 1 1 Starting Time Three-Phase Hz Three-Phase 6 Hz Braking Time W (1/ HP) [ 1 kg m ] 1 Overrun [ 1 kg m ] 1 3 Load Inertia J 6 [oz-in ] 1 3 Load Inertia J 6 [oz-in ] Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page A-31 Motor/Gearhead Mass: Motor. kg (6. lb.) Gearhead 1. kg (3.3 lb.) ϕ9 (ϕ3.) 1 (.3) 7. (.3) L (.16) 3 (1.6) 19 (.7) 11. (.) ϕ1.7.1 ϕ..7 (1/") 1 (.71) ϕ36 (ϕ1.) 9 (3.) Motor Gearhead Gear Ratio L DXF RKGN-AWMU RKGN-ME IKGN-SWM 9 (3.) 1±. (.9±.) GN SA Protective Earth Terminal M (1.6) 6 (.36) 16. (.6) A6AU A6BU 3 Motor Leads 3 mm (1 in.) Length UL Style 371, AWG Leads 3 mm (1 in.) Length UL Style 366, AWG ϕ6. (ϕ.6) Thru. (.) max. 1. (.) Protective Earth Terminal M Detail Drawing of Protective Earth Terminal A-13 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

23 Shaft Section of Round Shaft Type The motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass:. kg (6. lb.) A69 (.) 37 (1.6) 3 (1.1) 9 (.3) ϕ1.1 (ϕ ) ϕ3.3 (ϕ ) 9 ( 3.) ϕ6. (ϕ.6) Thru. Capacitor (Included with single-phase motors) A ϕ.3 (ϕ.169) AMP#17 (.79) B. (.1) (.16) 1 C (.39) B+1 (.39) 6 (.) Capacitor Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type 1±. (.9±.) Protective Earth Terminal M (.) max. Capacitor RKGN-AWMU RKA-AWMU CH1CFAUL RKGN-ME RKA-ME CH3BFAUL A B C (.) (.) (.7) (.7) 3 (1.3) 3 (1.3) Decimal Gearhead Can be connected to GN pinion shaft type. GN1XS Mass:.6 kg (1.3 lb.) A (.17) 37 1 (1.6) (.71) (.) Mass g (oz.) 6 (.1) 9 (.1) ϕ3.3 (ϕ ) 9 ( 3.) ϕ6. (ϕ.6) Thru Capacitor Cap Included 1±. (.9±.) Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-19 / Characteristics A-13 / Dimensions A-13 / Connection Diagrams A-13 A-131

24 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. represents the clockwise direction, while C represents the counterclockwise direction. Connection diagrams are also valid for the equivalent round shaft type. Single-Phase Motor RKGN-AWMU RKGN-ME L N R SW R R C C C ON ON C White Red Black C Motor Orange Orange Capacitor PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To rotate the motor in a clockwise () direction, turn SW to. To rotate the motor in a counterclockwise (C) direction, turn SW to C. Switch No. SW Specifications Single-Phase Single-Phase 11/11 VAC Input /3 VAC Input 1 VAC A minimum VAC A minimum (Inductive Load) (Inductive Load) Note Switched Simultaneously 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Three-Phase Motor IKGN-SWM L1(R) L(S) L3(T) R R R C C C Red White Black Motor Orange Orange PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To change the rotation direction, change any two connections between L1(R), L(S) and L3(T). Switch No. Specifications VAC A minimum (Inductive Load) Note Switched Simultaneously PE: Protective Earth R and C indicate CR circuit for surge suppression. [R = Ω, C =.1. μf, WV ( WV)] EPCR11- (CR circuit) is available as an accessory. Page A-3 How to connect a capacitor Page A-313 Gearhead, Accessories and Peripheral Equipment Space-Saving Gearheads Page A-39 Instantaneous Stop Pack Page A-77 Accessories Page A-7 A-13 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-1

25 Power Off Activated Type 6 W (1/1 HP) Frame Size: 9 mm ( 3. in.) Specifications Motor This type of motor does not contain a built-in friction brake mechanism. Output Rating Voltage Frequency Current Power Pinion Shaft Type Round Shaft Type W HP VAC Hz A 3 6 Single-Phase 11 RK6GE-AWMU RK6A-AWMU 6 1. minutes 1/1 Single-Phase 11 RK6GE-ME RK6A-ME 3 minutes IK6GE-SWM IK6A-SWM Continuous 6 1/1 6 1/1 Single-Phase 6.61 Single-Phase 3 Three-Phase Starting mn m oz-in Three-Phase. 6 Three-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 Details of safety standards Page G- Details of RoHS Directive Page G-3 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. (The power supply to the electromagnetic brake is kept and the brake is released.) When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. (Power Off Activated Type) Voltage Frequency Current Input Holding Motor mn m VAC Hz A W oz-in RK6GE-AWMU Single-Phase RK6A-AWMU Single-Phase Single-Phase 6 RK6GE-ME.7 1 RK6A-ME Single-Phase Single-Phase IK6GE-SWM IK6A-SWM Single-Phase 71 6 Single-Phase 3 (Gearhead sold separately) Rated Rated Speed Capacitor mn m oz-in r/min μf Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-13 / Characteristics A-13 / Dimensions A-13 / Connection Diagrams A-137 A-133

26 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) Product Line Motor Pinion Shaft Type Round Shaft Type RK6GE-AWMU RK6A-AWMU RK6GE-ME RK6A-ME IK6GE-SWM IK6A-SWM The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual Only for single-phase motors Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life GE-S Gearhead Hollow Shaft Solid Shaft Long Life GE-S Gearhead GE SA 3, 3.6,, 6, 7., 9, 1., 1, 1,, 3, 36,, 6, 7, 9, GE RH 1, 1, 1, 1 GE RAA GE1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Gasket, Operating Manual W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Gearmotor Table Gearheads and decimal gearheads are sold separately. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is % less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RK6GE-ME IK6GE-SWM GE SA GE SA Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RK6GE-AWMU RK6GE-ME IK6GE-SWM GE SA GE SA Gearmotor Table When Gearhead is Attached Page A- Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) Page A-16 Gearhead Page A-16 Permissible Load Inertia J of Gearhead Page A-17 A-13 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-133

27 Starting and Braking Characteristics (Reference values) Single-Phase Motor Overrun [Rotations] 3 1 Time [ms] 1 1 Single-Phase Hz Single-Phase 6 Hz Starting Time Overrun Braking Time [ 1 kg m ] Load Inertia J [oz-in ] Three-Phase Motor Overrun [Rotations] 3 1 Time [ms] 1 1 Three-Phase Hz Three-Phase 6 Hz Overrun Braking Time Starting Time [ 1 kg m ] Load Inertia J [oz-in ] Standard AC Introduction Induction Reversible Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page A-31 Motor/Gearhead Mass: Motor 3. kg (7. lb.) Gearhead 1. kg (3.3 lb.) A7U 16 (6.6) 3. (1.) 7. (.3) 6 (.6) 7 (.) 3 (1.) ϕ ϕ.6. (/") 9.±. (1.16±.). (1.13) ϕ17 (ϕ.67) 1 (.71) ϕ3 (ϕ1.3) No.1-UNC 1 (.39) Deep Cable: UL Style 17 ϕ (ϕ.31), mm ( in.) Length Cable Cores: 3 Motor Leads UL Style 371, AWG Leads UL Style 366, AWG Cable direction can be switched to the opposite direction. (.) max. 9 (3.6) 9 (3.) 7 (1.6) Protective Earth Terminal M 1±. 9 (3.) 9 (3.6) (.9±.) 1. (.7) ϕ6. (ϕ.6) Thru V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant 1. (.) Key and Key Slot (The key is included with the gearhead) Gearheads 16. (.6) Protective Earth Terminal M Detail Drawing of Protective Earth Terminal.±. (1.1±.) (.17.1 ) (.17.1 ) (.17 ) (.1 ) Linear Heads Pack Accessories Installation Product Line A-13 / Characteristics A-13 / Dimensions A-13 / Connection Diagrams A-137 A-13

28 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) Shaft Section of Round Shaft Type The mass and motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass: 3. kg (7. lb.) A71 (.) 37 (1.6) 3 (1.1) 11 (.3) (ϕ.7.7 ) ϕ1.1 (ϕ ) ϕ3.3 9 ( 3.) 9 (3.6) ϕ6. (ϕ.6) Thru 1±. (.9±.) 9 (3.6) Decimal Gearhead Can be connected to GE pinion shaft type. GE1XS Mass:.6 kg (1.3 lb.) A9 61 (.) (1.7) 1 (.3) (.) ϕ3.3 (ϕ ) 9 ( 3.) ϕ1. (ϕ.) Thru 1±. (.9±.) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Protective Earth Terminal M Capacitor (Included with single-phase motors) A ϕ.3 (ϕ.169) AMP#17 (.79) C B 7 (.) 1 (.39) B+1 (.9) R1 (R.39) 7 (1.6) 6 (.) 1. (.7) Capacitor Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type Capacitor RK6GE-AWMU RK6A-AWMU CHCFAUL RK6GE-ME RK6A-ME CHBFAUL (.16) A B C (.) (.) 9 (1.1) 9 (1.1) 1 (1.61) 1 (1.61) Mass g (oz.) 91 (3.) 93 (3.3) Capacitor Cap Included A-136 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-133

29 Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. represents the clockwise direction, while C represents the counterclockwise direction. Connection diagrams are also valid for the equivalent round shaft type. Single-Phase Motor Three-Phase Motor RK6GE-AWMU RK6GE-ME IK6GE-SWM L N L1(R) L(S) L3(T) R SW R R C C C ON ON C R R R C C C White Red Black C Orange Orange Capacitor Red White Black Motor Motor Orange Orange PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To rotate the motor in a clockwise () direction, turn SW to. To rotate the motor in a counterclockwise (C) direction, turn SW to C. Switch No. PE: Protective Earth R and C indicate CR circuit for surge suppression. [R = Ω, C =.1. μf, WV ( WV)] EPCR11- (CR circuit) is available as an accessory. Page A-3 How to connect a capacitor Page A-313 Gearhead, Accessories and Peripheral Equipment Space-Saving Gearheads Page A-39 Instantaneous Stop Pack Page A-77 Accessories Page A-7 PE SW Specifications Single-Phase Single-Phase 11/11 VAC Input /3 VAC Input 1 VAC A minimum VAC A minimum (Inductive Load) (Inductive Load) Note Switched Simultaneously operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To change the rotation direction, change any two connections between L1(R), L(S) and L3(T). Switch No. Specifications VAC A minimum (Inductive Load) Note Switched Simultaneously Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-13 / Characteristics A-13 / Dimensions A-13 / Connection Diagrams A-137 A-137

30 Standard AC Power Off Activated Type 9 W (1/ HP) Frame Size: 9 mm ( 3. in.) (Gearhead sold separately) 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Specifications Motor This type of motor does not contain a built-in friction brake mechanism. Pinion Shaft Type Round Shaft Type Rating RK9GE-AWMU RK9A-AWMU 3 minutes RK9GE-ME RK9A-ME 3 minutes IK9GE-SWM IK9A-SWM Continuous Output Power Voltage Frequency Current W HP VAC Hz A 9 1/ 9 1/ 9 1/ Single-Phase 11 Single-Phase Single-Phase 6.96 Starting mn m oz-in Single-Phase Three-Phase Three-Phase Three-Phase The U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate is the approved model name. Page G-11 Details of safety standards Page G- Details of RoHS Directive Page G-3 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. (The power supply to the electromagnetic brake is kept and the brake is released.) When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. Rated Rated Speed Capacitor mn m oz-in r/min μf (Power Off Activated Type) Voltage Frequency Current Input Holding Motor mn m VAC Hz A W oz-in RK9GE-AWMU Single-Phase RK9A-AWMU Single-Phase Single-Phase 6 RK9GE-ME.7 1 RK9A-ME Single-Phase Single-Phase IK9GE-SWM IK9A-SWM Single-Phase 71 6 Single-Phase 3 A-13 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-13

31 Product Line Motor Pinion Shaft Type Round Shaft Type RK9GE-AWMU RK9A-AWMU RK9GE-ME RK9A-ME IK9GE-SWM IK9A-SWM The following items are included in each product. Motor, Capacitor, Capacitor Cap, Operating Manual Only for single-phase motors Parallel Shaft Gearhead/ Gearhead (Sold separately) Gearhead Type Gearhead Gear Ratio Parallel Shaft Shaft Parallel Shaft Long Life GE-S Gearhead Hollow Shaft Solid Shaft Long Life GE-S Gearhead GE SA 3, 3.6,, 6, 7., 9, 1., 1, 1,, 3, 36,, 6, 7, 9, GE RH 1, 1, 1, 1 GE RAA GE1XS (Decimal Gearhead) The following items are included in each product. Parallel Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Operating Manual Hollow Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Safety Cover (with screws), Gasket, Operating Manual Solid Shaft Gearhead Gearhead, Mounting Screws, Parallel Key, Gasket, Operating Manual Standard AC Introduction Induction Reversible Gearmotor Table Gearheads and decimal gearheads are sold separately. Enter the gear ratio in the box ( ) within the gearhead model name. A colored background ( ) indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. The speed is calculated by dividing the motor's synchronous speed ( Hz: 1 r/min, 6 Hz: 1 r/min) by the gear ratio. The actual speed is % less than the displayed value, depending on the load. To reduce the speed beyond the gear ratio in the table, attach a decimal gearhead (gear ratio 1:1) between the gearhead and the motor. In that case, the permissible torque is N m ( lb-in). Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RK9GE-ME IK9GE-SWM GE SA GE SA Hz Unit = Upper values: N m/lower values: lb-in Speed r/min Motor/ Gear Ratio Gearhead RK9GE-AWMU RK9GE-ME IK9GE-SWM GE SA GE SA GE SA Gearmotor Table When Gearhead is Attached Page A Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) Page A-16 Gearhead Page A-16 Permissible Load Inertia J of Gearhead Page A V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-139 / Characteristics A-1 / Dimensions A-1 / Connection Diagrams A-1 A-139

32 Standard AC Starting and Braking Characteristics (Reference values) Single-Phase Motor Single-Phase Hz Single-Phase 6 Hz Three-Phase Motor Three-Phase Hz Three-Phase 6 Hz W (1/1 HP) 1 W (1/ HP) W (1/3 HP) Overrun [Rotations] 3 1 Time [ms] 1 Braking Time Starting Time Overrun Overrun [Rotations] 3 1 Time [ms] 1 Braking Time Starting Time Overrun W (1/19 HP) [ 1 kg m ] Load Inertia J [oz-in ] [ 1 kg m ] Load Inertia J [oz-in ] 6 W (1/1 HP) Dimensions Unit = mm (in.) Mounting screws are included with gearheads. Dimensions for mounting screws Page A-31 9 W (1/ HP) W (1/ HP) Motor/Gearhead Mass: Motor 3.9 kg (.6 lb.) Gearhead 1. kg (3.3 lb.) A7U 179 (7.) 7. (.3) 6 (.6) 7 (.) 3 (1.) ϕ ϕ.6. (/") 9.±. (1.16±.). (1.13) 9 (3.6) 9 (3.) 1±. (.9±.) 3. (1.) Cable: UL Style 17 ϕ (ϕ.31), mm ( in.) Length Cable Cores: 3 Motor Leads UL Style 371, AWG Leads UL Style 366, AWG Cable direction can be switched to the opposite direction. ϕ17 (ϕ.67) 1 (.71) ϕ3 (ϕ1.3) No.1-UNC 1 (.39) Deep (.) max. 7 (1.6) Protective Earth Terminal M 9 (3.) 9 (3.6) 1. (.7) ϕ6. (ϕ.6) Thru 1. (.) Key and Key Slot (The key is included with the gearhead) 16. (.6) Protective Earth Terminal M.±. (1.1±.) (.17.1 ) (.17.1 ) (.17 ) (.1 ) Detail Drawing of Protective Earth Terminal A-1 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-13

33 Shaft Section of Round Shaft Type The mass and motor s dimensions (excluding the shaft section) are the same as those of the pinion shaft types. Mass: 3.9 kg (.6 lb.) A73 (.) 37 (1.6) 3 (1.1) 11 (.3) (ϕ.7.7 ) ϕ1.1 (ϕ3.677 ).1 ϕ3.3 9 ( 3.) 9 (3.6) ϕ6. (ϕ.6) Thru 1±. (.9±.) 9 (3.6) Decimal Gearhead Can be connected to GE pinion shaft type. GE1XS Mass:.6 kg (1.3 lb.) A9 61 (.) (1.7) 1 (.3) (.) ϕ3.3 (ϕ ) 9 ( 3.) ϕ1. (ϕ.) Thru 1±. (.9±.) Standard AC Introduction Induction Reversible Protective Earth Terminal M 7 (1.6) Capacitor (Included with single-phase motors) A ϕ.3 (ϕ.169) AMP#17 (.79) C B 7 (.) 1 (.39) (.16) B+1 (.9) R1 (R.39) 6 (.) 1. (.7) Capacitor Dimensions Unit = mm (in.) Pinion Shaft Type Round Shaft Type RK9GE-AWMU RK9A-AWMU Capacitor CH3CFAUL RK9GE-ME RK9A-ME CH7BFAUL A B C (.) (.) 3 (1.3) 3 (1.3) (1.97) (1.97) Mass g (oz.) 1 (.9) 13 (.9) Capacitor Cap Included V Series Clutch & Synchronous Low-Speed Synchronous Watertight, Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Product Line A-139 / Characteristics A-1 / Dimensions A-1 / Connection Diagrams A-1 A-11

34 Standard AC 6 W (1/1 HP) 1 W (1/ HP) W (1/3 HP) W (1/19 HP) Connection Diagrams The direction of motor rotation is as viewed from the shaft end of the motor. represents the clockwise direction, while C represents the counterclockwise direction. Connection diagrams are also valid for the equivalent round shaft type. Single-Phase Motor RK9GE-AWMU RK9GE-ME L N R SW R R C C C ON ON C White Red Black C Motor Orange Orange Capacitor PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To rotate the motor in a clockwise () direction, turn SW to. To rotate the motor in a counterclockwise (C) direction, turn SW to C. Switch No. SW Specifications Single-Phase Single-Phase 11/11 VAC Input /3 VAC Input 1 VAC A minimum VAC A minimum (Inductive Load) (Inductive Load) Note Switched Simultaneously 6 W (1/1 HP) 9 W (1/ HP) W (1/ HP) Three-Phase Motor IK9GE-SWM L1(R) L(S) L3(T) R R R C C C Red White Black Motor Orange Orange PE operates both motor and electromagnetic brake action. The electromagnetic brake will be released and the motor will rotate when is switched simultaneously to ON. When is switched simultaneously to OFF, the motor stops immediately with the electromagnetic brake and holds the load. If you wish to release the brake while the motor is stopped, apply voltage between the two brake lead wires (orange). Rotation Direction To change the rotation direction, change any two connections between L1(R), L(S) and L3(T). Switch No. Specifications VAC A minimum (Inductive Load) Note Switched Simultaneously PE: Protective Earth R and C indicate CR circuit for surge suppression. [R = Ω, C =.1. μf, WV ( WV)] EPCR11- (CR circuit) is available as an accessory. Page A-3 How to connect a capacitor Page A-313 Gearhead, Accessories and Peripheral Equipment Space-Saving Gearheads Page A-39 Instantaneous Stop Pack Page A-77 Accessories Page A-7 A-1 ORIENTAL MOTOR GENERAL CATALOG 9/1 Features A-11 / System Configuration A-113 / Specifications A-13

35 Induction BH Series Power Off Activated W (1/ HP) Frame Size: 1 mm (.9 in.) Features High Power W (1/ HP) Smallest frame size among W (1/ HP) motors Hypoid Gear-Employed Gearheads Right-angle gearheads employ hypoid gears. Hollow shafts and solid shafts are available to enable space-saving. RoHS-Compliant The BH Series conforms to the RoHS Directive that prohibits the use of six chemical substances including lead and cadmium. Details of RoHS Directive Page G-3 Specifications Continuous Rating Combination Type BHI6FMT- RH BHI6FMT- RA BHI6FMT- BHI6EMT- RH BHI6EMT- RA BHI6EMT- BHI6SMT- RH BHI6SMT- RA BHI6SMT- Round Shaft Type BHI6FMT-A BHI6EMT-A BHI6SMT-A Output Power Voltage Frequency Current W HP VAC Hz A 1/ 1/ 1/ Single-Phase 11 Single-Phase 11 "Combination Type" for Easy Installation The combination type comes with the motor and gearhead pre-assembled. This enables easy installation in equipment. Combination Type: The combination type comes with the motor and its dedicated gearhead pre-assembled, which simplifies installation in equipment. and gearheads are also available separately to facilitate changes or repairs. 6 3 Single-Phase 6 1. Single-Phase 3 Three-Phase 6 6 Three-Phase 6 Three-Phase Starting N m oz-in The values for each specification applies to the motor only. Details of safety standards Page G- List of safety standard approved products (, Standards, Standards File No., Certification Body) Page G-11 : Contains a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. (The power supply to the electromagnetic brake is kept and the brake is released.) When the motor temperature drops, the thermal protector closes and the motor restarts. Be sure to turn the motor power off before inspecting. (Power Off Activated Type) Voltage Frequency Current Input Holding Motor N m VAC Hz A W oz-in BHI6FMT- RH, BHI6FMT- RA Single-Phase BHI6FMT-, BHI6FMT-A Single-Phase 11 1 BHI6EMT- RH, BHI6EMT- RA BHI6EMT-, BHI6EMT-A BHI6SMT- RH, BHI6SMT- RA BHI6SMT-, BHI6SMT-A Single-Phase Single-Phase 3 6 Single-Phase 6 Single-Phase 6 Single-Phase Hollow Shaft Rated Rated Speed Capacitor N m oz-in r/min μf Parallel Shaft Standard AC Introduction Induction Reversible V Series Clutch & Synchronous Low-Speed Watertight, Synchronous Dust-Resistant Gearheads Linear Heads Pack Accessories Installation Characteristics A-1 / Dimensions A-16 / Connection Diagrams A-1 / Motor and Gearhead Combinations A-11 A-13